Code was completey bitrotten
Code was a partial test (and yet 500 lines already)
Shader is more and more complex and multithreading support greatly
reduce the cost of shader switch
Nvidia allows to get the ASM of the shader of the compiled shader. It is useful
to check the performance.
It also allow me to compile most of shader code path for QA
Dump is enabled in linux replayer + debug_glsl_shader = 2
Code is not yet enabled because it requires extensive test
The idea is to replace point by a 1 pixels sprite with the help of
a geometry shader. In 4x, point will be replaced by a 4x4 sprite.
Partially invalidate RT when there is a write in the middle of it (actually 2 pages below)
Code is not yet enabled because
1/ I want to stabilize latest update
2/ not sure of the impact of the code
3/ maybe it need a more generic version
Frame is always 32 bits but game can reuse it later as a 16 bits RT.
Fix half screen issue with Ricky Ponting Cricket
Unfortunately it triggers texture shuffle wrongly. I hope there is no
regression.
Fix depth issue.
First issue: RT and Depth are located at the same address.
=> solution, just lookup the depth (done for any games)
Second issue: Instead to draw a X,Y rectangle, they draw a 32 pix, 4096 pix
rectangle with a FBW of 1.
=> solution, don't bother just write the depth directly
Please someone add some CRC to enable the code
// GL42 interact very badly with sw blending. GL42 uses the primitiveID to find the primitive
// that write the bad alpha value. Sw blending will force the draw to run primitive by primitive
// (therefore primitiveID will be constant to 1)
It is mostly the texture shuffle effect which is now emulated correctly on openGL
They remain in the Dx level as speedhack in particular for
* Castlevania;
* GodOfWar;
* StarOcean3;
* ValkyrieProfile2;
* RadiataStories;
Remove old commented hack: Drakengard2, ArctheLad, ReZ
Separate hacks that are only enabled in aggressive mode
It might save a couple of fps
Add a define to test the perf if we keep only the blue channel. It brokes
the code in Prince Of Persia that use the Red/Green channel... Maybe the
speed hack :( Or find a way to replace all if with a lookup table
Note: it is only supported on OpenGL currently
Code unscale the texture to ease the conversion. Quality is awful (same as before)
but I'm not sure we can support an upscaled texture
Maybe the quality loss is due to the reduction without mipmap
Maybe the best solution will be to add an hack to extract the blue channel
(with texture swizzle), and uses a "full page/screen" spirte instead.
(it would be faster too)
Note: won't be compatible with MSAA (but gl doesn't support it anyway)
// In theory new textures contain invalidated data. Still in theory a new target
// must contains the content of the GS memory.
// In practice, TC will wrongly invalidate some RT. For example due to write on the alpha
// channel but colors is still valid. Unfortunately TC doesn't support the upload of data
// in target.
//
// Cleaning the code here will likely break several games. However it might reduce
// the noise in draw call debugging. It is the main reason to enable it on debug build.
//
// From a performance point of view, it might cost a little on big upscaling
// but normally few RT are miss so it must remain reasonable.
Game can directly uploads a background or the full image in
"CTRC" buffer. Previous code was a full black screen.
It will also avoid various black screen issue in gs dump.
hidden option: preload_frame_with_gs_data
Note: impact on upscaling was not tested and it's likely broken
Improve the rendering in MGS3 (even if the game is still broken
due to others TC issues)
// Typical bug (MGS3 blue cloud):
// 1/ RT used as 32 bits => alpha channel written
// 2/ RT used as 24 bits => no update of alpha channel
// 3/ Lookup of texture that used alpha channel as index, HasSharedBits will return false
// because of the previous draw call format
//
// Solution: consider the RT as 32 bits if the alpha was used in the past
"Regression" introduced in 8 bits RT support
The case appears when
1/ address of RT is the same as input texture
2/ input format is 8 bits
3/ previous lookup of RT was miss
It avoid various upscaling glitches on GS post-processing effect
// 1/ Palette is used to interpret the alpha channel of the RT as an index.
// Star Ocean 3 uses it to emulate a stencil buffer.
// 2/ Z formats are a bad idea to interpolate (discontinuties).
// 3/ 16 bits buffer is used to move data from a channel to another.
//
// I keep linear filtering for standard color even if I'm not sure that it is
// working correctly.
// Indeed, texture is reduced so you need to read all covered pixels (9 in 3x)
// to correctly interpolate the value. Linear interpolation is likely acceptable
// only in 2x scaling
//
// Src texture will still be bilinear interpolated so I'm really not sure
// that we need to do it here too.
//
// Future note: instead to do
// RT 2048x2048 -> T 1024x1024 -> RT 2048x2048
// We can maybe sample directly a bigger texture
// RT 2048x2048 -> T 2048x2048 -> RT 2048x2048
// Pro: better quality. Copy instead of StretchRect (must be faster)
// Cons: consume more memory
//
// In distant future: investigate to reuse the RT directly without any
// copy. Likely a speed boost and memory usage reduction.
It might help to fix a bit the color on a couple of games
accurate_fbmask = 1
Code uses GL4.5 extensions. So far it seems the effect is ony used a couple
of time and often in non-overlapping primitive. Speed impact will likely remain small
It seems to impacts lots of games that still have issue (VP2, MTG3, PoP)
The PSMT32 format is read a PSMT8. I think we need to convert it as PSMT8H (i.e.
unpack it to have only an alpha channel)
To clear a (W, H) RT/Depth, GS can only send a (W , H/2) primitive with
a Z (or RT) pointer in the middle of the buffer
Top-half will be cleared by the color (or the depth).
Bottom-half will be cleared by the depth (or the color).
Code isn't enabled yet but it was tested with success on GoW2.
GS doesn't supports texture shuffle/swizzle so it is emulated in a
complex way.
The idea is to read/write the 32 bits color format as a 16 bit format.
This way, RG (16 lsb bits) or BA (16 msb bits) can be read or written with
square texture that targets pixels 1-8 or pixels 8-16.
However shuffle is limited. For example you can copy the green channel
to either the alpha channel or another green channel.
Note: Partial masking of channel is not yet implemented
V2: improve logging
V3: better support of green channel in shader
V4: improve detection of destination (issue due to rounding)
Gow uses 24 bits buffer, so only color is updated but blending is configured as Cd
so it is a NOP
In this case, we don't lookup the target in the texture cache. It reduces the complexity
to handle depth which can be located at same address as RT
Note: please test DX renderer
Rework the renderer selection logic to reload the saved renderer after
it's been changed in the config panel and to properly detect whether a
renderer toggle has been requested.
Changed the name of the Direct3D renderers so they would match the way
they are named in GSdx's Plugin Settings window. Also changed a printf
to say OpenCL instead of opencl.
Just use 1 in skip draw if you want to use it
openGL code will soon be fixed to support depth correctly (and I hope dx in the future)
Conflicts:
plugins/GSdx/GSState.cpp
plugins/GSdx/GSState.h
Old way various check boxes to configure the plugin
New way an unified drop down list
* Level 0 (dev only) => disable (mostly) all hacks and auto skip depth.
* Level 1 (dev only ) => enable oi/oo/cu hacks, others remains disabled
* Level 2 (GL) => enable most hacks except a couple of one that were fixed on openGL (speed impact)
* Level 3 (DX) => enable all hacks
* Level 4 => enable also aggresive CRC
Note: windows gui must be updated, and it will be nice to create a global tooltip
Gregory: Get all changes but keep C11 code path which will be the future
(if someone can find info on Visual Studio support)
* Keep the old posix api to use address sanitizer on gcc 4.9
Conflicts:
common/build/Utilities/utilities.vcxproj.filters
common/build/Utilities/utilities_vs2012.vcxproj.filters
common/build/Utilities/utilities_vs2013.vcxproj.filters
common/include/Utilities/MemcpyFast.h
common/include/Utilities/StringHelpers.h
common/src/Utilities/AlignedMalloc.cpp
common/src/Utilities/vssprintf.cpp
plugins/GSdx/stdafx.cpp
-Last commit broke Snowblind games again
-Width now based on output circuit
-Try to use the smallest possible while being at least the size of the screen
The idea is to easily extract bad frame from gs dump and to compare them
with the sw renderer.
Here the summary of the options:
savet => dump all input textures
save => dump the render target
savez => dump the depth buffer
savef => dump the frame
The idea will be to replace StretchRect for standard case with a framebuffer
blit. Potentially it toggles less gl state.
Worth a test on Star Ocean 3 that uses a lots this function for stencil emulation
Gregory Hainaut