Before this change, we simply fail if the device does not expose one
queue family that supports both graphics and present. Currently this is
fine, since devices tend to lay out their queues in this way. NV, for
instance, tends to have one queue family for all graphics operations and
one more for transfer only. However, it's not a hard requirement, and it
is cheap to use a separate queue, so we might as well.
Currently, this is only the logic op bit, but this will be extended to
the framebuffer fetch/blend modes. In the future, when/if we move to
VideoCommon pipelines, this state will be part of the pipeline UID
anyway, and we can mask it out in the backend by using a two-level map,
so the shaders/programs are shared.
Based on hardware tests, masking occurs for the accelerator registers.
This fixes Red Steel and Far Cry Vengeance, which rely on this behavior
when reading back the current playback position from the DSP.
This reverts commit d23fd17e1a.
Dynamic sampler indexing is broken in VK_NV_glsl as of 385.41. The
performance gap doesn't seem to be as wide with the updated driver, so
to save maintaining two code paths, it's easier to just drop the
extension support completely.
ImgTec's driver uses a major.minor@changeID versioning system
This is packed into a double so "1.9@4850625" becomes "109.4850625"
The next release brnach is expected to be 1.10, hence the need for 2
digits for the branch minor.
The changeID should be unique for each build, but is shared over all
branches, so only makes sense to compare withing a branch.
It's likely branch 'major' versions will be used for major hardware
revisions, and the drivers for both maintained in parallel. Thus it
may not make sense to compare versions between different major
verisons - if/when this happens we can hook up a DriverDetails::Family
as needed.
CNTVCT_EL0 is force-enabled on all linux plattforms.
Windows is untested, but as this is the best way to get *any* low
overhead performance counters, they likely use it as well.
Within Cleanup(), it is called at *every* end of the block. This generates bigger code,
but it is the only way to handle blocks with multiple exit nodes.
This optimisation doesn't work on PowerVR's Vulkan implementation. We
(incorrectly) disallow Framebuffer objects to be used with a different
load or store op than that which they were created with, despite the
spec allowing such.
This fixes the windwaker intro "smearing"
Modernizes the arrays and makes future simplifications possible (e.g. usages within the software renderer).
It also makes cases where we use array->pointer decay explicit.
This apparently fixes https://bugs.dolphin-emu.org/issues/10499 somehow.
The first changed line of this commit is just for performance - the
second changed line is where the difference in behavior is.
It would fail on lines line "Value =" - IE a value set to emptystring.
This would cause the app to crash when trying to open the corresponding
settings window.
* IOCTL_WFSI_PREPARE_DEVICE -> IOCTL_WFSI_IMPORT_TITLE_INIT
(equivalent of ES_ImportTitleInit, also the official name)
* IOCTL_WFSI_IMPORT_TITLE -> IOCTL_WFSI_IMPORT_TITLE_CANCEL
(equivalent of ES_ImportTitleCancel)
The class NonCopyable is, like the name says, supposed to disallow
copying. But should it allow moving?
For a long time, NonCopyable used to not allow moving. (It declared
a deleted copy constructor and assigment operator without declaring
a move constructor and assignment operator, making the compiler
implicitly delete the move constructor and assignment operator.)
That's fine if the classes that inherit from NonCopyable don't need
to be movable or if writing the move constructor and assignment
operator by hand is fine, but that's not the case for all classes,
as I discovered when I was working on the DirectoryBlob PR.
Because of that, I decided to make NonCopyable movable in c7602cc,
allowing me to use NonCopyable in DirectoryBlob.h. That was however
an unfortunate decision, because some of the classes that inherit
from NonCopyable have incorrect behavior when moved by default-
generated move constructors and assignment operators, and do not
explicitly delete the move constructors and assignment operators,
relying on NonCopyable being non-movable.
So what can we do about this? There are four solutions that I can
think of:
1. Make NonCopyable non-movable and tell DirectoryBlob to suck it.
2. Keep allowing moving NonCopyable, and expect that classes that
don't support moving will delete the move constructor and
assignment operator manually. Not only is this inconsistent
(having classes disallow copying one way and disallow moving
another way), but deleting the move constructor and assignment
operator manually is too easy to forget compared to how tricky
the resulting problems are.
3. Have one "MovableNonCopyable" and one "NonMovableNonCopyable".
It works, but it feels rather silly...
4. Don't have a NonCopyable class at all. Considering that deleting
the copy constructor and assignment operator only takes two lines
of code, I don't see much of a reason to keep NonCopyable. I
suppose that there was more of a point in having NonCopyable back
in the pre-C++11 days, when it wasn't possible to use "= delete".
I decided to go with the fourth one (like the commit title says).
The implementation of the commit is fairly straight-forward, though
I would like to point out that I skipped adding "= delete" lines
for classes whose only reason for being uncopyable is that they
contain uncopyable classes like File::IOFile and std::unique_ptr,
because the compiler makes such classes uncopyable automatically.
I'm not sure why this hasn't popped up as an error on the buildbots,
but the build fails on my new install of VS2017. The error is C2445:
result type of conditional expression is ambiguous: types 'wxString'
and 'const char [1]' can be converted to multiple common types
to get bigger, breaking an optimization. This forces the emitter to use a
32bit pointer instead of an 8bit one, fixing the issue at the expense of
efficiency.
Seems like I was wrong that ANDI2R doesn't require a temporary register here.
There is *one* case when the mask won't fit in the ARM AND instruction:
mask = 0xFFFFFFFF
But let's just use MOV instead of AND here for this case...
Currently, GameFile returns a generic banner if the file didn't have one
available (either because the file format doesn't support it, or because
it's a Wii file without an associated save).
It makes more sense to handle the lack of banner in the UI layer. The
game list will use the generic missing banner explicitly (no change from before), and the game info window now omits the banner display entirely if the file didn't have one (since it's not useful to display/allow the user to save the "missing banner" banner).
Stenzek