Also disabled the gsdx AF options for the OGL renderer (because it's not implemented for that yet).
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5881 96395faa-99c1-11dd-bbfe-3dabce05a288
Adds anisotropic texture filtering (1x-16x) to the hardware settings. Enhances the visual quality of textures that are at oblique viewing angles.
Anisotropic filtering is automatically disabled if: 8-bit textures are enabled.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5878 96395faa-99c1-11dd-bbfe-3dabce05a288
Slight adjustments to positions in the GUI also (OCD'd the spacing a little :P)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5796 96395faa-99c1-11dd-bbfe-3dabce05a288
Added a check box and config code for the fxaa shader.
It's not currently hooked up since the shader setup might get replaced in a day or two.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5777 96395faa-99c1-11dd-bbfe-3dabce05a288
Probably only of interest to testers (and me). Absolutely do NOT select the reference device even out of extreme morbid curiosity. It's not even very good at being a reference despite being slower than you can probably believe.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5358 96395faa-99c1-11dd-bbfe-3dabce05a288
Now, a note about the actual issue. Destination alpha tests can be used on the GS as one of the workarounds for a lack of stencils. If you use a destination alpha test and leave alpha writing on, the GS will only write each pixel until you write an alpha value which would fail the test. This works to a point in gsdx without further hacking, but that point is when within a single batch of primitives the same pixels are written multiple times and the destination alpha test is expected to update. I did experimentally make a tight loop updating the stencil with a draw then drawing for one primitive at a time, but it was prohibitively slow (over 80% fps loss, you really don't want to know).
Destination alpha testing cannot be directly implemented in D3D9 or D3D10, but (probably) can in D3D11 (with a speed hit for sure, but I doubt it'll be 80%). I'll be getting a new graphics card and looking into that.
And before some idiot says it, the answer is no. OpenGL does not help.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5346 96395faa-99c1-11dd-bbfe-3dabce05a288
Also set the auto deinterlace mode in GSdx when the .ini isn't present (instead of "none").
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5270 96395faa-99c1-11dd-bbfe-3dabce05a288
- Added "Aggressive-CRC" checkbox at the HW hacks section of the config dialog.
- The following hacks are now activated only in aggressive mode:
- God of War 2: disable water effect/lines, disable global haze.
- FFX, FFX2, SSX3 (the full crc hack from r5214).
- Shadow of the Colossus: disable (over)bloom.
- Reverted the Valkyrie Profile 2 hack to pre- r5214.
- Some CRC fixes by comments on r5214.
- Regression fix of dynamic crc hack (INITIAL_MODE = 0 didn't compile)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5221 96395faa-99c1-11dd-bbfe-3dabce05a288
Mouse over descriptions for the hacks. Thanks to KrossX again, these are great :)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5123 96395faa-99c1-11dd-bbfe-3dabce05a288
Adding KrossX's Wild Arms text alignment hack to the new dialog box. This hack is actually very interesting for a number of games. It should work well in cases where game designers adjusted everything pixel perfect for the GS, that usually breaks with upscaling.
It should be generalized and renamed later.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5120 96395faa-99c1-11dd-bbfe-3dabce05a288
Team effort of KrossX and myself:
Finally adding that special game fixes / hack dialog I talked about for a while.
Committing this in several steps to clean up any issues easier.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5116 96395faa-99c1-11dd-bbfe-3dabce05a288
Committing a hack KrossX prepared (thanks) ;)
It can be used to fix bad character sprites in Gust games.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5101 96395faa-99c1-11dd-bbfe-3dabce05a288
Let users set software parameters (extra threads and line AA) regardless of currently configured renderer.
Makes testing far easier.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5051 96395faa-99c1-11dd-bbfe-3dabce05a288
- 0: no multi-threading
- 1: gif packet processing and texture uploads run parallel with rendering, the slowest decides the fps, dual-cores can still suffer by the spin loops, I'll check that when I compile pcsx2 on my notebook
- 2: two rendering threads, on a decent cpu packet processing is going to be slower now, this is probably going to increase fps the most on quads
- 3: small fps increase
- 4+: even smaller.
If you have a quad cpu with HT, 6 is the max, 1 + 1 is needed for pcsx2 and gsdx's basic tasks.
Also hacked palette writes to not force a read-back in hw mode (added in previous rev), it hit render targets in a surprising large number of games.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@4998 96395faa-99c1-11dd-bbfe-3dabce05a288
- Allow filtering setting for native resolution hardware rendering, as it's not tied to the resolution.
- Add ST / UV coordinate tweaking defines to more easily debug small rendering glitches.
- Add a define to bypass the hardware renderer texture cache. With this enabled, speed drops to slower than software rendering.
It fixes nearly all hardware rendering issues though and can be used to see how games *would* look if we had a new cache ;)
Thanks for the help, sudonim :)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@4635 96395faa-99c1-11dd-bbfe-3dabce05a288
- GSWnd is not implemented, no config dialogs either
- no output, just the null device
- threading classes were not tested (my first experience with pthread)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@4315 96395faa-99c1-11dd-bbfe-3dabce05a288
Gregory Hainaut