Allow both user-only and system mode to run pa2.0 cpus.
Avoid creating a separate qemu-system-hppa64 binary;
force the qemu-hppa binary to use TARGET_ABI32.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Hoist the resolution of d up one level above do_unit_cond.
All computations are logical, and are simplified by using a mask of the
correct width, after which the result may be compared with zero.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Hoist the resolution of d up one level above do_sed_cond.
The MOVB comparison and the existing shift/extract/deposit
are all 32-bit.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The sar shift amount register is limited to 5 bits when running
a 32-bit CPU. Strip off the remaining bits.
The interesting part is, that this register allows to detect at runtime
if a physical CPU is capable to execute PA2.0 (64-bit) instructions.
Signed-off-by: Helge Deller <deller@gmx.de>
We need to make sure the link is masked properly along the
use_nullify_skip path. The other three settings of a link
register already use this.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This will be how we ensure that the IAOQ is always
valid per PSW.W, therefore all stores to these two
variables must be done with this function.
Use third argument -1 if the destination is always dynamic,
and fourth argument NULL if the destination is always static.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In form_gva and cpu_get_tb_cpu_state, we must truncate when PSW_W == 0.
In space_select, the bits that choose the space depend on PSW_W.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Prepare for the qemu binary supporting both pa10 and pa20
at the same time.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Select the proper carry bit for input to the arithmetic
and for output for the condition.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This instruction always uses the input carry from bit 32,
but produces all 16 output carry bits.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The destination is TCGv_i32, so use tcg_gen_qemu_ld_i32
not tcg_gen_qemu_ld_reg.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace with tcg_temp_new_tl without recording into ctx.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace with tcg_temp_new without recording into ctx.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use a separate mmu index for PSW_P enabled vs disabled.
This means we can elide the tlb flush in cpu_hppa_put_psw
when PSW_P changes. This turns out to be the majority
of all tlb flushes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow the name 'cpu_env' to be used for something else.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the hppa diag instruction to support Block-TLBs
when called with the 0x100 value.
The diag_btlb() helper function does all necessary steps
to emulate the PDC BTLB firmware function, which includes
providing BTLB info, adding a new BTLB, deleting a BTLB
and removing all BTLBs.
Signed-off-by: Helge Deller <deller@gmx.de>
All these files only access the translator_ld/st API declared
in "exec/translator.h". The CPU ld/st API from declared in
"exec/cpu_ldst.h" is not used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-5-philmd@linaro.org>
Add two macros which convert privilege level to/from MMU index:
- PRIV_TO_MMU_IDX(priv)
returns the MMU index for the given privilege level
- MMU_IDX_TO_PRIV(mmu_idx)
returns the corresponding privilege level for this MMU index
The introduction of those macros make the code easier to read and
will help to improve performance in follow-up patch.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
New wrapper around gen_io_start which takes care of the USE_ICOUNT
check, as well as marking the DisasContext to end the TB.
Remove exec/gen-icount.h.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In preparation for compiling tcg/ only once, eliminate
the all_helpers array. Instantiate the info structs for
the generic helpers in accel/tcg/, and the structs for
the target-specific helpers in each translate.c.
Since we don't see all of the info structs at startup,
initialize at first use, using g_once_init_* to make
sure we don't race while doing so.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All uses were read-write, so replace with a new
allocation and initialization.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use a C test instead of a pre-processor test for the id.
Use tcg_constant_i64 instead of tcg_const_i64.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Translators are no longer required to free tcg temporaries.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This wasn't actually used at all, just some unused
macro re-definitions.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In preparation for returning the number of insns generated
via the same pointer. Adjust only the prototypes so far.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The fid instruction (Floating-Point Identify) puts the FPU model and
revision into the Status Register. Since those values shouldn't be 0,
store values there which a PCX-L2 (for 32-bit) or a PCX-W2 (for 64-bit)
would return. Noticed while trying to install MPE/iX.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Qemu currently emulates a 32-bit CPU only, and crashes with this error
when it faces a 64-bit load (e.g. "ldd 0(r26),r0") or a 64-bit store
(e.g. "std r26,0(r26)") instruction in the guest:
ERROR:../qemu/tcg/tcg-op.c:2822:tcg_canonicalize_memop: code should not be reached
Add checks for 64-bit sizes and generate an illegal instruction
exception if necessary.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Pass these along to translator_loop -- pc may be used instead
of tb->pc, and host_pc is currently unused. Adjust all targets
at one time.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have fetched and locked the logfile in translator_loop.
Pass the filepointer down to the disas_log hook so that it
need not be fetched and locked again.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-13-richard.henderson@linaro.org>
Replace a config-time define with a compile time condition
define (compatible with clang and gcc) that must be declared prior to
its usage. This avoids having a global configure time define, but also
prevents from bad usage, if the config header wasn't included before.
This can help to make some code independent from qemu too.
gcc supports __BYTE_ORDER__ from about 4.6 and clang from 3.2.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[ For the s390x parts I'm involved in ]
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Almost all PA-RISC machines have either a button that is labeled with 'TOC' or
a BMC/GSP function to trigger a TOC. TOC is a non-maskable interrupt that is
sent to the processor. This can be used for diagnostic purposes like obtaining
a stack trace/register dump or to enter KDB/KGDB in Linux.
This patch adds support for such an emulated TOC button.
It wires up the qemu monitor "nmi" command to trigger a TOC. For that it
provides the hppa_nmi function which is assigned to the nmi_monitor_handler
function pointer. When called it raises the EXCP_TOC hardware interrupt in the
hppa_cpu_do_interrupt() function. The interrupt function then calls the
architecturally defined TOC function in SeaBIOS-hppa firmware (at fixed address
0xf0000000).
According to the PA-RISC PDC specification, the SeaBIOS firmware then writes
the CPU registers into PIM (processor internal memmory) for later analysis. In
order to write all registers it needs to know the contents of the CPU "shadow
registers" and the IASQ- and IAOQ-back values. The IAOQ/IASQ values are
provided by qemu in shadow registers when entering the SeaBIOS TOC function.
This patch adds a new aritificial opcode "getshadowregs" (0xfffdead2) which
restores the original values of the shadow registers. With this opcode SeaBIOS
can store those registers as well into PIM before calling an OS-provided TOC
handler.
To trigger a TOC, switch to the qemu monitor with Ctrl-A C, and type in the
command "nmi". After the TOC started the OS-debugger, exit the qemu monitor
with Ctrl-A C.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson