initialization of IDC_ROUND_SPRITE
set&get config for round offset.
three state checkbox for the hack.
define IDC for round offset.
Linux (GUI) refresh.
typo
Also disabled the gsdx AF options for the OGL renderer (because it's not implemented for that yet).
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5881 96395faa-99c1-11dd-bbfe-3dabce05a288
Adds anisotropic texture filtering (1x-16x) to the hardware settings. Enhances the visual quality of textures that are at oblique viewing angles.
Anisotropic filtering is automatically disabled if: 8-bit textures are enabled.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5878 96395faa-99c1-11dd-bbfe-3dabce05a288
Slight adjustments to positions in the GUI also (OCD'd the spacing a little :P)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5796 96395faa-99c1-11dd-bbfe-3dabce05a288
Added a check box and config code for the fxaa shader.
It's not currently hooked up since the shader setup might get replaced in a day or two.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5777 96395faa-99c1-11dd-bbfe-3dabce05a288
Probably only of interest to testers (and me). Absolutely do NOT select the reference device even out of extreme morbid curiosity. It's not even very good at being a reference despite being slower than you can probably believe.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5358 96395faa-99c1-11dd-bbfe-3dabce05a288
Now, a note about the actual issue. Destination alpha tests can be used on the GS as one of the workarounds for a lack of stencils. If you use a destination alpha test and leave alpha writing on, the GS will only write each pixel until you write an alpha value which would fail the test. This works to a point in gsdx without further hacking, but that point is when within a single batch of primitives the same pixels are written multiple times and the destination alpha test is expected to update. I did experimentally make a tight loop updating the stencil with a draw then drawing for one primitive at a time, but it was prohibitively slow (over 80% fps loss, you really don't want to know).
Destination alpha testing cannot be directly implemented in D3D9 or D3D10, but (probably) can in D3D11 (with a speed hit for sure, but I doubt it'll be 80%). I'll be getting a new graphics card and looking into that.
And before some idiot says it, the answer is no. OpenGL does not help.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5346 96395faa-99c1-11dd-bbfe-3dabce05a288
Also set the auto deinterlace mode in GSdx when the .ini isn't present (instead of "none").
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5270 96395faa-99c1-11dd-bbfe-3dabce05a288
- Added "Aggressive-CRC" checkbox at the HW hacks section of the config dialog.
- The following hacks are now activated only in aggressive mode:
- God of War 2: disable water effect/lines, disable global haze.
- FFX, FFX2, SSX3 (the full crc hack from r5214).
- Shadow of the Colossus: disable (over)bloom.
- Reverted the Valkyrie Profile 2 hack to pre- r5214.
- Some CRC fixes by comments on r5214.
- Regression fix of dynamic crc hack (INITIAL_MODE = 0 didn't compile)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5221 96395faa-99c1-11dd-bbfe-3dabce05a288
Mouse over descriptions for the hacks. Thanks to KrossX again, these are great :)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5123 96395faa-99c1-11dd-bbfe-3dabce05a288
Adding KrossX's Wild Arms text alignment hack to the new dialog box. This hack is actually very interesting for a number of games. It should work well in cases where game designers adjusted everything pixel perfect for the GS, that usually breaks with upscaling.
It should be generalized and renamed later.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5120 96395faa-99c1-11dd-bbfe-3dabce05a288
refraction