In 2005 the author of commit daa579632d "PS2 mouse and keyboard
separation (Paul Brook)" and 0e43e99c04 "PS2 mouse and keyboard
separation (Paul Brook)" separated the PS/2 controller code and
the PS/2 keyboard and mouse code. It seems he forgot to remove
a few defines. Remove them now.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-11-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently the PS/2 controller command KBD_CCMD_MOUSE_DISABLE
doesn't disable the PS/2 mouse communication at all, and the
PS/2 controller commands KBD_CCMD_KBD_DISABLE and
KBD_CCMD_KBD_ENABLE only disable and enable the keyboard
interrupt, which is very different from what a real PS/2
controller does. A guest may notice the difference.
Mask out pending data on disabled queues to correctly disable
the PS/2 controller communication.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-10-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace reads of the variable s->pending with a call to a new
function kbd_pending() to ease the review of the next patch.
There is no functional change.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-9-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a separate queue for PS/2 controller responses. The
responses no longer get queued in the keyboard or mouse queues.
The advantage of this can be seen after the next two patches,
where the guest can disable the PS/2 communication with keyboard
and mouse and still talk to the PS/2 controller.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-8-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently there is only one flag to distinguish between two
interrupt sources and there are no available flags for more
sources. Add an internal state variable to store the interrupt
source. The next patch will introduce an additional interrupt
source. There is no functional change.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-7-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Limit the keyboard data rate to the serial link speed. Some old
DOS software relies on being able to read an incoming scan-code
more than once. After reading keyboard data from the i8042
controller, the guest software has 1ms to read the same data
again.
Use -global i8042.kbd-throttle=on to enable this feature.
To see how this patch works, start a FreeDOS 1.2 guest with the
qemu option -global i8042.kbd-throttle=on and open a text file
with the vim 7.3 32 bit for DOS executable. Then use the cursor
keys (not the cursor keys on the numeric keypad) to move through
the text. Without the kbd-throttle option enabled each keystroke
will move the cursor two positions.
Buglink: https://bugs.launchpad.net/bugs/1895363
Buglink: https://bugs.launchpad.net/bugs/1897568
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-6-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Split out the interrupt line changing code from kbd_update_irq().
This is a preparation for the next patch. There is no functional
change.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-4-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Don't deassert the irq twice if the queue is empty. While the
second deassertion doesn't do any harm, it's unnecessary.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-3-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
ps2_queue() behaves differently than the very similar functions
ps2_queue_2() to ps2_queue_4(). The first one calls update_irq()
even if the queue is full, the others don't. Change ps2_queue()
to be consistent with the others.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-2-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 7abe7eb294 "ps2: Fix mouse stream corruption due to lost data"
added code to avoid mouse stream corruptions but the calculation of
the needed free queue size was wrong. Fix this.
To reproduce, open a text file with the vim 7.3 32 bit for DOS exe-
cutable in a FreeDOS client started with -display sdl and move the
mouse around for a few seconds. You will quickly see erratic mouse
movements and unexpected mouse clicks. CuteMouse (ctmouse.exe) in
FreeDOS doesn't try to re-sync the mouse stream.
Fixes: 7abe7eb294 ("ps2: Fix mouse stream corruption due to lost data")
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210525181441.27768-1-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It is interesting to know if the PS2 keyboard is in translated mode, and
which of the three scancode sets are in use.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210309155804.306051-1-berrange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The SSE-300 has an ITCM at 0x0000_0000 and a DTCM at 0x2000_0000.
Currently we model these in the AN547 board, but this is conceptually
wrong, because they are a part of the SSE-300 itself. Move the
modelling of the TCMs out of mps2-tz.c into sse300.c.
This has no guest-visible effects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-7-peter.maydell@linaro.org
Currently we model the ITCM in the AN547's RAMInfo list. This is incorrect
because this RAM is really a part of the SSE-300. We can't just delete
it from the RAMInfo list, though, because this would make boot_ram_size()
assert because it wouldn't be able to find an entry in the list covering
guest address 0.
Allow a board to specify a boot RAM size manually if it doesn't have
any RAM itself at address 0 and is relying on the SSE for that, and
set the correct value for the AN547. The other boards can continue
to use the "look it up from the RAMInfo list" logic.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-6-peter.maydell@linaro.org
Convert armsse_realize() to use ERRP_GUARD(), following
the rules in include/qapi/error.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-5-peter.maydell@linaro.org
The SSE-300 was not correctly modelling its internal SRAMs:
* the SRAM address width default is 18
* the SRAM is mapped at 0x2100_0000, not 0x2000_0000 like
the SSE-200 and IoTKit
The default address width is no longer guest-visible since
our only SSE-300 board sets it explicitly to a non-default
value, but following the hardware's default will help for
any future boards we need to model.
Reported-by: Devaraj Ranganna <devaraj.ranganna@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-4-peter.maydell@linaro.org
The AN547 sets the SRAM_ADDR_WIDTH for the SSE-300 to 21;
since this is not the default value for the SSE-300, model this
in mps2-tz.c as a per-board value.
Reported-by: Devaraj Ranganna <devaraj.ranganna@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-3-peter.maydell@linaro.org
The SRAM at 0x2000_0000 is part of the SSE-200 itself, and we model
it that way in hw/arm/armsse.c (along with the associated MPCs). We
incorrectly also added an entry to the RAMInfo array for the AN524 in
hw/arm/mps2-tz.c, which was pointless because the CPU would never see
it. Delete it.
The bug had no guest-visible effect because devices in the SSE-200
take priority over those in the board model (armsse.c maps
s->board_memory at priority -2).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-2-peter.maydell@linaro.org
In icc_eoir_write() we assume that we can identify the group of the
IRQ being completed based purely on which register is being written
to and the current CPU state, and that "CPU state matches group
indicated by register" is the only necessary access check.
This isn't correct: if the CPU is not in Secure state then EOIR1 will
only complete Group 1 NS IRQs, but if the CPU is in EL3 it can
complete both Group 1 S and Group 1 NS IRQs. (The pseudocode
ICC_EOIR1_EL1 makes this clear.) We were also missing the logic to
prevent EOIR0 writes completing G0 IRQs when they should not.
Rearrange the logic to first identify the group of the current
highest priority interrupt and then look at whether we should
complete it or ignore the access based on which register was accessed
and the state of the CPU. The resulting behavioural change is:
* EL3 can now complete G1NS interrupts
* G0 interrupt completion is now ignored if the GIC
and the CPU have the security extension enabled and
the CPU is not secure
Reported-by: Chan Kim <ckim@etri.re.kr>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510150016.24910-1-peter.maydell@linaro.org
6d9cd115b9 ("hw/arm/smmuv3: Enforce invalidation on a power of two range")
failed to completely fix misalignment issues with range
invalidation. For instance invalidations patterns like "invalidate 32
4kB pages starting from 0xff395000 are not correctly handled" due
to the fact the previous fix only made sure the number of invalidated
pages were a power of 2 but did not properly handle the start
address was not aligned with the range. This can be noticed when
boothing a fedora 33 with protected virtio-blk-pci.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Fixes: 6d9cd115b9 ("hw/arm/smmuv3: Enforce invalidation on a power of two range")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Quote docs/devel/style.rst (section "Automatic memory deallocation"):
* Variables declared with g_auto* MUST always be initialized,
otherwise the cleanup function will use uninitialized stack memory
Initialize @name properly to get rid of the compilation error (using
gcc-7.3.0 on CentOS):
../hw/remote/proxy.c: In function 'pci_proxy_dev_realize':
/usr/include/glib-2.0/glib/glib-autocleanups.h:28:3: error: 'name' may be used uninitialized in this function [-Werror=maybe-uninitialized]
g_free (*pp);
^~~~~~~~~~~~
../hw/remote/proxy.c:350:30: note: 'name' was declared here
g_autofree char *name;
^~~~
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Message-id: 20210312112143.1369-1-yuzenghui@huawei.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The vfio_ccw_unrealize() routine makes an unconditional attempt to
unregister every IRQ notifier, though they may not have been registered
in the first place (when running on an older kernel, for example).
Let's mirror this behavior in the error cleanups in vfio_ccw_realize()
so that if/when new IRQs are added, it is less confusing to recognize
the necessary procedures. The worst case scenario would be some extra
messages about an undefined IRQ, but since this is an error exit that
won't be the only thing to worry about.
And regarding those messages, let's change it to a warning instead of
an error, to better reflect their severity. The existing code in both
paths handles everything anyway.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Acked-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20210428143652.1571487-1-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Instead of having all TYPE_CCW_DEVICE children set the bus type to
TYPE_VIRTUAL_CSS_BUS, do it once in the abstract parent.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20210424145313.3287400-1-f4bug@amsat.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 690e29b911 ("vfio-ccw: Refactor ccw irq handler") changed
one of the checks for the IRQ notifier registration from saying
"the host needs to recognize the only IRQ that exists" to saying
"the host needs to recognize ANY IRQ that exists."
And this worked fine, because the subsequent change to support the
CRW IRQ notifier doesn't get into this code when running on an older
kernel, thanks to a guard by a capability region. The later addition
of the REQ(uest) IRQ by commit b2f96f9e4f ("vfio-ccw: Connect the
device request notifier") broke this assumption because there is no
matching capability region. Thus, running new QEMU on an older
kernel fails with:
vfio: unexpected number of irqs 2
Let's adapt the message here so that there's a better clue of what
IRQ is missing.
Furthermore, let's make the REQ(uest) IRQ not fail when attempting
to register it, to permit running vfio-ccw on a newer QEMU with an
older kernel.
Fixes: b2f96f9e4f ("vfio-ccw: Connect the device request notifier")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20210421152053.2379873-1-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
- various fixes for binfmt_misc docker images
- add hexagon check-tcg support docker image
- add tricore check-tcg support
- refactor ppc docker images
- add missing ppc64le tests
- don't use host_cc for test fallback
- check-tcg configure.sh tweaks for cross compile/clang
- fix some memory leaks in plugins
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmCjfMEACgkQ+9DbCVqe
KkQ+aQf/QX5prjX9IW64GzwmZLdgufrc9fwdbrhyNTglcS0gN/hti6is3gBhe9dU
KynWvmjvnosDT1EI53ciVkSRrwDLptpyq3bz140RjmSmPFQvUP16yF3KTThBxXuO
1BZk7iq5jzv3jVHD4j4zQPyMRatyBBToKtIboSZntljq6WTomv8gWu8+vdlWGzeG
0ubW1k9YHZNnQ0Et5xjqQBgBbjoOQvbkLYwNyyDjkOem8p4oKFIyTcRP9PYSJ9t3
cq314LuFJVjW1TMywvgHOlZEwzqRqOtdzW1RC1EbVqYR+lifAgYRI/kTEwL3Ab7j
Z+hybdzlfJdUPNiJ5Q4rjDpuKI+1Nw==
=FYwg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-plugin-updates-180521-2' into staging
testing and plugin updates:
- various fixes for binfmt_misc docker images
- add hexagon check-tcg support docker image
- add tricore check-tcg support
- refactor ppc docker images
- add missing ppc64le tests
- don't use host_cc for test fallback
- check-tcg configure.sh tweaks for cross compile/clang
- fix some memory leaks in plugins
# gpg: Signature made Tue 18 May 2021 09:37:21 BST
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-plugin-updates-180521-2: (29 commits)
configure: use cc, not host_cc to set cross_cc for build arch
tests/tcg: don't allow clang as a cross compiler
tests/tcg: fix missing return
tests/tcg/ppc64le: tests for brh/brw/brd
tests/docker: gcc-10 based images for ppc64{,le} tests
tests/tcg/tricore: Add muls test
tests/tcg/tricore: Add msub test
tests/tcg/tricore: Add madd test
tests/tcg/tricore: Add ftoi test
tests/tcg/tricore: Add fmul test
tests/tcg/tricore: Add fadd test
tests/tcg/tricore: Add dvstep test
tests/tcg/tricore: Add clz test
tests/tcg/tricore: Add bmerge test
tests/tcg/tricore: Add macros to create tests and first test 'abs'
configure: Emit HOST_CC to config-host.mak
tests/tcg/tricore: Add build infrastructure
hw/tricore: Add testdevice for tests in tests/tcg/
tests/tcg: Run timeout cmds using --foreground
tests/tcg: Add docker_as and docker_ld cmds
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Next set of ppc related patches for qemu-6.1. Highlights are:
* Start of a significant softmmu cleanup from Richard Henderson
* Further work towards allowing builds without CONFIG_TCG
-----BEGIN PGP SIGNATURE-----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=FI4M
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.1-20210519' into staging
ppc patch queue 2021-05-19
Next set of ppc related patches for qemu-6.1. Highlights are:
* Start of a significant softmmu cleanup from Richard Henderson
* Further work towards allowing builds without CONFIG_TCG
# gpg: Signature made Wed 19 May 2021 13:36:45 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210519: (48 commits)
target/ppc: Remove type argument for mmubooke206_get_physical_address
target/ppc: Remove type argument from mmubooke206_check_tlb
target/ppc: Remove type argument from mmubooke_get_physical_address
target/ppc: Remove type argument from mmubooke_check_tlb
target/ppc: Remove type argument from mmu40x_get_physical_address
target/ppc: Remove type argument from get_bat_6xx_tlb
target/ppc: Remove type argument from ppc6xx_tlb_check
target/ppc: Remove type argument from ppc6xx_tlb_pte_check
target/ppc: Remove type argument from check_prot
target/ppc: Use MMUAccessType in mmu_helper.c
target/ppc: Rename access_type to type in mmu_helper.c
target/ppc: Use MMUAccessType in mmu-hash32.c
target/ppc: Use MMUAccessType in mmu-hash64.c
target/ppc: Use MMUAccessType in mmu-radix64.c
target/ppc: Introduce prot_for_access_type
target/ppc: Fix load endianness for lxvwsx/lxvdsx
target/ppc: Use translator_loop_temp_check
target/ppc: Mark helper_raise_exception* as noreturn
target/ppc: Tidy exception vs exit_tb
target/ppc: Move single-step check to ppc_tr_tb_stop
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- vhost-user-blk: Fix error handling during initialisation
- Add test cases for the vhost-user-blk export
- Fix leaked Transaction objects
- qcow2: Expose dirty bit in 'qemu-img info'
-----BEGIN PGP SIGNATURE-----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=Xe4O
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
- vhost-user-blk: Fix error handling during initialisation
- Add test cases for the vhost-user-blk export
- Fix leaked Transaction objects
- qcow2: Expose dirty bit in 'qemu-img info'
# gpg: Signature made Tue 18 May 2021 11:57:46 BST
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
vhost-user-blk: Check that num-queues is supported by backend
virtio: Fail if iommu_platform is requested, but unsupported
vhost-user-blk: Get more feature flags from vhost device
vhost-user-blk: Improve error reporting in realize
vhost-user-blk: Don't reconnect during initialisation
vhost-user-blk: Make sure to set Error on realize failure
vhost-user-blk-test: test discard/write zeroes invalid inputs
tests/qtest: add multi-queue test case to vhost-user-blk-test
test: new qTest case to test the vhost-user-blk-server
block/export: improve vu_blk_sect_range_ok()
block: Fix Transaction leak in bdrv_reopen_multiple()
block: Fix Transaction leak in bdrv_root_attach_child()
qcow2: set bdi->is_dirty
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Moved has_spr to cpu.h as ppc_has_spr and turned it into an inline function.
Change spr verification in pnv.c and spapr.c to a version that can
compile in a !TCG environment.
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Message-Id: <20210507164146.67086-1-lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The function ppc_hash64_filter_pagesizes has been moved from a function
with prototype in mmu-hash64.h and implemented in mmu-hash64.c to
a static function in hw/ppc/spapr_caps.c as it's only used in that file.
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Message-Id: <20210506163941.106984-3-lucas.araujo@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The hypercalls h_enter, h_remove, h_bulk_remove, h_protect, and h_read,
have been moved to spapr_softmmu.c with the functions they depend on. The
functions is_ram_address and push_sregs_to_kvm_pr are not static anymore
as functions on both spapr_hcall.c and spapr_softmmu.c depend on them.
The hypercalls h_resize_hpt_prepare and h_resize_hpt_commit have been
divided, the KVM part stayed in spapr_hcall.c while the softmmu part
was moved to spapr_softmmu.c
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Message-Id: <20210506163941.106984-2-lucas.araujo@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Starting with Linux kernel v5.12 we dropped support[1] in KVM for
hosts that can't have their threads running in different MMU modes
(POWER9 < DD2.2). In these hosts, KVM will no longer report the
KVM_CAP_PPC_MMU_HASH_V3 capability[2] when the host is running Radix.
For guests that support both MMU modes, the negotiation during CAS
will make sure it selects the correct one.
For guests that only support Hash, such as P8 compat mode guests, the
following error is currently thrown:
$ ~/qemu-system-ppc64 -machine pseries,accel=kvm,max-cpu-compat=power8 ...
error: kvm run failed Invalid argument
NIP 0000000000000100 LR 0000000000000000 CTR 0000000000000000 XER 0000000000000000 CPU#0
MSR 8000000000001000 HID0 0000000000000000 HF 8000000000000000 iidx 3 didx 3
TB 00000000 00000000 DECR 0
GPR00 0000000000000000 0000000000000000 0000000000000000 000000007ff00000
GPR04 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR08 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR12 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR16 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR28 0000000000000000 0000000000000000 0000000000000000 0000000000000000
CR 00000000 [ - - - - - - - - ] RES ffffffffffffffff
SRR0 0000000000000000 SRR1 0000000000000000 PVR 00000000004e1201 VRSAVE 0000000000000000
SPRG0 0000000000000000 SPRG1 0000000000000000 SPRG2 0000000000000000 SPRG3 0000000000000000
SPRG4 0000000000000000 SPRG5 0000000000000000 SPRG6 0000000000000000 SPRG7 0000000000000000
HSRR0 0000000000000000 HSRR1 0000000000000000
CFAR 0000000000000000
LPCR 000000000004f01f
PTCR 0000000000000000 DAR 0000000000000000 DSISR 0000000000000000
This patch adds a verification during the writing of the platform
support vector so that we error out as soon as we determine this guest
only supports Hash and the host doesn't.
~/qemu-system-ppc64 -machine pseries,accel=kvm,max-cpu-compat=power8 ...
qemu-system-ppc64: Guest requested unavailable MMU mode (hash).
1- https://git.kernel.org/torvalds/p/b1b1697ae0cc8
2- https://git.kernel.org/torvalds/p/a722076e94702
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20210505001130.3999968-3-farosas@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A following patch will make use of it.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20210505001130.3999968-2-farosas@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Creating a device with a number of queues that isn't supported by the
backend is pointless, the device won't work properly and the error
messages are rather confusing.
Just fail to create the device if num-queues is higher than what the
backend supports.
Since the relationship between num-queues and the number of virtqueues
depends on the specific device, this is an additional value that needs
to be initialised by the device. For convenience, allow leaving it 0 if
the check should be skipped. This makes sense for vhost-user-net where
separate vhost devices are used for the queues and custom initialisation
code is needed to perform the check.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1935031
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20210429171316.162022-7-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 2943b53f6 (' virtio: force VIRTIO_F_IOMMU_PLATFORM') made sure
that vhost can't just reject VIRTIO_F_IOMMU_PLATFORM when it was
requested. However, just adding it back to the negotiated flags isn't
right either because it promises support to the guest that the device
actually doesn't support. One example of a vhost-user device that
doesn't have support for the flag is the vhost-user-blk export of QEMU.
Instead of successfully creating a device that doesn't work, just fail
to plug the device when it doesn't support the feature, but it was
requested. This results in much clearer error messages.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1935019
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20210429171316.162022-6-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
VIRTIO_F_RING_PACKED and VIRTIO_F_IOMMU_PLATFORM need to be supported by
the vhost device, otherwise advertising it to the guest doesn't result
in a working configuration. They are currently not supported by the
vhost-user-blk export in QEMU.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1935020
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20210429171316.162022-5-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that vhost_user_blk_connect() is not called from an event handler
any more, but directly from vhost_user_blk_device_realize(), we can
actually make use of Error again instead of calling error_report() in
the inner function and setting a more generic and therefore less useful
error message in realize() itself.
With Error, the callers are responsible for adding context if necessary
(such as the "-device" option the error refers to). Additional prefixes
are redundant and better omitted.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20210429171316.162022-4-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is a partial revert of commits 77542d4314 and bc79c87bcd.
Usually, an error during initialisation means that the configuration was
wrong. Reconnecting won't make the error go away, but just turn the
error condition into an endless loop. Avoid this and return errors
again.
Additionally, calling vhost_user_blk_disconnect() from the chardev event
handler could result in use-after-free because none of the
initialisation code expects that the device could just go away in the
middle. So removing the call fixes crashes in several places.
For example, using a num-queues setting that is incompatible with the
backend would result in a crash like this (dereferencing dev->opaque,
which is already NULL):
#0 0x0000555555d0a4bd in vhost_user_read_cb (source=0x5555568f4690, condition=(G_IO_IN | G_IO_HUP), opaque=0x7fffffffcbf0) at ../hw/virtio/vhost-user.c:313
#1 0x0000555555d950d3 in qio_channel_fd_source_dispatch (source=0x555557c3f750, callback=0x555555d0a478 <vhost_user_read_cb>, user_data=0x7fffffffcbf0) at ../io/channel-watch.c:84
#2 0x00007ffff7b32a9f in g_main_context_dispatch () at /lib64/libglib-2.0.so.0
#3 0x00007ffff7b84a98 in g_main_context_iterate.constprop () at /lib64/libglib-2.0.so.0
#4 0x00007ffff7b32163 in g_main_loop_run () at /lib64/libglib-2.0.so.0
#5 0x0000555555d0a724 in vhost_user_read (dev=0x555557bc62f8, msg=0x7fffffffcc50) at ../hw/virtio/vhost-user.c:402
#6 0x0000555555d0ee6b in vhost_user_get_config (dev=0x555557bc62f8, config=0x555557bc62ac "", config_len=60) at ../hw/virtio/vhost-user.c:2133
#7 0x0000555555d56d46 in vhost_dev_get_config (hdev=0x555557bc62f8, config=0x555557bc62ac "", config_len=60) at ../hw/virtio/vhost.c:1566
#8 0x0000555555cdd150 in vhost_user_blk_device_realize (dev=0x555557bc60b0, errp=0x7fffffffcf90) at ../hw/block/vhost-user-blk.c:510
#9 0x0000555555d08f6d in virtio_device_realize (dev=0x555557bc60b0, errp=0x7fffffffcff0) at ../hw/virtio/virtio.c:3660
Note that this removes the ability to reconnect during initialisation
(but not during operation) when there is no permanent error, but the
backend restarts, as the implementation was buggy. This feature can be
added back in a follow-up series after changing error paths to
distinguish cases where retrying could help from cases with permanent
errors.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210429171316.162022-3-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We have to set errp before jumping to virtio_err, otherwise the caller
(virtio_device_realize()) will take this as success and crash when it
later tries to access things that we've already freed in the error path.
Fixes: 77542d4314
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210429171316.162022-2-kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
this device is used to verify the correctness of regression tests by
allowing guests to write their exit status to this device. This is then
used by qemu to exit using the written status.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210305170045.869437-4-kbastian@mail.uni-paderborn.de>
Message-Id: <20210512102051.12134-14-alex.bennee@linaro.org>
With the introduction of the nvme-subsystem device we are really
cluttering up the hw/block directory.
As suggested by Philippe previously, move the nvme emulation to hw/nvme.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Validation of the max_active and max_open zoned parameters are
independent of any other state, so move them to the early
nvme_ns_check_constraints parameter checks.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
It is not an error to report more active/open zones supported than the
number of zones in the namespace.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The NvmeCtrl num_namespaces member is just an indirection for the
NVME_MAX_NAMESPACES constant.
Remove the indirection.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Streamline namespace array indexing such that both the subsystem and
controller namespaces arrays are 1-indexed.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
There is no need to look up the lba size and metadata size in the LBA
Format structure everytime we want to use it. And we use it a lot.
Cache the values in the NvmeNamespace and update them if the namespace
is formatted.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The inline nvme_ns_status() helper only has a single call site. Remove
it from the header file and inline it for real.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
In preparation for moving the nvme device into its own subtree, merge
the header files into one.
Also add missing copyright notice and add list of authors with
substantial contributions.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Get rid of the (reserved) double underscore use.
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Get rid of the (reserved) double underscore use.
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Get rid of the (reserved) double underscore use. Rename the "generic"
zone open function to nvme_zrm_open_flags() and add a generic `int
flags` argument instead which allows more flags to be easily added in
the future. There is at least one TP under standardization that would
add an additional flag.
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
While QEMU coding style prefers lowercase hexadecimals in constants, the
NVMe subsystem uses the format from the NVMe specifications in comments,
i.e. 'h' suffix instead of '0x' prefix.
Fix this up across the code base.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: updated message; added conversion in a couple of missing comments]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_map_addr_pmr function arguments not aligned, fix that.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Currently IO Command Set Profile feature is supported, but the feature
support flag not set. Further, this feature is changable. Fix that.
Additionally, remove filling default value of the CQE result with zero,
since it will fall back to the default case anyway.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: fix up commit message]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Currently in compare command metadata aio read blk_aio_preadv return
value ignored. Consider it and complete the block accounting.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Fixes: 0a384f923f ("hw/block/nvme: add compare command")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Currently pci_nvme_err_invalid_lba_range trace is called individually at
each nvme_check_bounds() call site.
Move the trace event to nvme_check_bounds() and remove the redundant
events.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[k.jensen: commit message fixup]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmCeiMEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpqsIH/A49Av5Bv8huL75lf9GzCx3E1a/z2W9Fphik
OcQ1ahR+7CRDARub+vTG40MBmZBVefIWjLAj3BwBWzFGPX0DZq0zeI102VzlEVKY
OeUx8ixuiKOSLcS+QxE7ZXIBL2Pn7l+MFUi4nLMYKti7c/kola7zlB57qsmXh+VD
AOQ7Utj6NWoi6QocWJsMSCyHCh3Fk9QzcStLlr6/MkSJa1zqv8l22+8oWH07Fk2M
wZfhrm9k094on28iSejsFYL5e4ROeXUajbOdfyMIxWvAB7boC9Jxk/e0oAbuSB4y
2f71Gfk3mU6irS7PvrxcKbk6BVD2zxM2WumOchZJgxFAujDO6yg=
=fvkT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,virtio: bugfixes, improvements
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 14 May 2021 15:27:13 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
Fix build with 64 bits time_t
vhost-vdpa: Make vhost_vdpa_get_device_id() static
hw/virtio: enable ioeventfd configuring for mmio
hw/smbios: support for type 41 (onboard devices extended information)
checkpatch: Fix use of uninitialized value
virtio-scsi: Configure all host notifiers in a single MR transaction
virtio-scsi: Set host notifiers and callbacks separately
virtio-blk: Configure all host notifiers in a single MR transaction
virtio-blk: Fix rollback path in virtio_blk_data_plane_start()
pc-dimm: remove unnecessary get_vmstate_memory_region() method
amd_iommu: fix wrong MMIO operations
virtio-net: Constify VirtIOFeature feature_sizes[]
virtio-blk: Constify VirtIOFeature feature_sizes[]
hw/virtio: Pass virtio_feature_get_config_size() a const argument
x86: acpi: use offset instead of pointer when using build_header()
amd_iommu: Fix pte_override_page_mask()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/arm/virt.c
As it's only used inside hw/virtio/vhost-vdpa.c.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-Id: <20210413133737.1574-1-yuzenghui@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds ioeventfd flag for virtio-mmio configuration.
It allows switching ioeventfd on and off.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Message-Id: <161700379211.1135943.8859209566937991305.stgit@pasha-ThinkPad-X280>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Type 41 defines the attributes of devices that are onboard. The
original intent was to imply the BIOS had some level of control over
the enablement of the associated devices.
If network devices are present in this table, by default, udev will
name the corresponding interfaces enoX, X being the instance number.
Without such information, udev will fallback to using the PCI ID and
this usually gives ens3 or ens4. This can be a bit annoying as the
name of the network card may depend on the order of options and may
change if a new PCI device is added earlier on the commande line.
Being able to provide SMBIOS type 41 entry ensure the name of the
interface won't change and helps the user guess the right name without
booting a first time.
This can be invoked with:
$QEMU -netdev user,id=internet
-device virtio-net-pci,mac=50:54:00:00:00:42,netdev=internet,id=internet-dev \
-smbios type=41,designation='Onboard LAN',instance=1,kind=ethernet,pcidev=internet-dev
The PCI segment is assumed to be 0. This should hold true for most
cases.
$ dmidecode -t 41
# dmidecode 3.3
Getting SMBIOS data from sysfs.
SMBIOS 2.8 present.
Handle 0x2900, DMI type 41, 11 bytes
Onboard Device
Reference Designation: Onboard LAN
Type: Ethernet
Status: Enabled
Type Instance: 1
Bus Address: 0000:00:09.0
$ ip -brief a
lo UNKNOWN 127.0.0.1/8 ::1/128
eno1 UP 10.0.2.14/24 fec0::5254:ff:fe00:42/64 fe80::5254:ff:fe00:42/64
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Message-Id: <20210401171138.62970-1-vincent@bernat.ch>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows the virtio-scsi-pci device to batch the setup of all its
host notifiers. This significantly improves boot time of VMs with a
high number of vCPUs, e.g. from 6m5.563s down to 1m2.884s for a
pseries machine with 384 vCPUs.
Note that memory_region_transaction_commit() must be called before
virtio_bus_cleanup_host_notifier() because the latter might close
ioeventfds that the transaction still assumes to be around when it
commits.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210407143501.244343-5-groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Host notifiers are guaranteed to be idle until the callbacks are
hooked up with virtio_queue_aio_set_host_notifier_handler(). They
thus don't need to be set or unset with the AioContext lock held.
Do this outside the critical section, like virtio-blk already
does : basically downgrading virtio_scsi_vring_init() to only
setup the host notifier and set the callback in the caller.
This will allow to batch addition/deletion of ioeventds in
a single memory transaction, which is expected to greatly
improve initialization time.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210407143501.244343-4-groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows the virtio-blk-pci device to batch the setup of all its
host notifiers. This significantly improves boot time of VMs with a
high number of vCPUs, e.g. from 3m26.186s down to 0m58.023s for a
pseries machine with 384 vCPUs.
Note that memory_region_transaction_commit() must be called before
virtio_bus_cleanup_host_notifier() because the latter might close
ioeventfds that the transaction still assumes to be around when it
commits.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210407143501.244343-3-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When dataplane multiqueue support was added in QEMU 2.7, the path
that would rollback guest notifiers assignment in case of error
simply got dropped.
Later on, when Error was added to blk_set_aio_context() in QEMU 4.1,
another error path was introduced, but it ommits to rollback both
host and guest notifiers.
It seems cleaner to fix the rollback path in one go. The patch is
simple enough that it can be adjusted if backported to a pre-4.1
QEMU.
Fixes: 51b04ac5c6 ("virtio-blk: dataplane multiqueue support")
Cc: stefanha@redhat.com
Fixes: 97896a4887 ("block: Add Error to blk_set_aio_context()")
Cc: kwolf@redhat.com
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210407143501.244343-2-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The get_vmstate_memory_region() method from PCDIMMDeviceClass is only
ever called from this class and is never overridden, so it can be converted
into an ordinary function.
This saves us from having to do an indirect call in order to reach it.
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <f42da25471dc4b967796642388294e61e6587047.1619303649.git.maciej.szmigiero@oracle.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Address was swapped with value when writing MMIO registers, so the user
saw garbage in lot of cases. The interrupt status was not correctly set.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Message-Id: <20210427110504.10878-1-rka@sysgo.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch set adds a bus multiplexer and the necessary infrastructure
in the I2C code to allow it to work.
These are common on systems with lots of I2C devices, like an IPMI BMC.
-----BEGIN PGP SIGNATURE-----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=IamZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-v1' into staging
Add a bus multiplexer device
This patch set adds a bus multiplexer and the necessary infrastructure
in the I2C code to allow it to work.
These are common on systems with lots of I2C devices, like an IPMI BMC.
# gpg: Signature made Thu 13 May 2021 22:48:07 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-v1:
hw/i2c: add pca954x i2c-mux switch
hw/i2c: move search to i2c_scan_bus method
hw/i2c: add match method for device search
hw/i2c: name I2CNode list in I2CBus
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The VirtIOFeature structure isn't modified, mark it const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210511104157.2880306-2-philmd@redhat.com>
Fix of the 2021-05-11 version, with a fix to build on the armhf
cross.
The largest change in this set is David's changes for ram block size
changing; then there's a pile of other cleanups and fixes.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=RJvy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20210513a' into staging
Migration pull 2021-05-13
Fix of the 2021-05-11 version, with a fix to build on the armhf
cross.
The largest change in this set is David's changes for ram block size
changing; then there's a pile of other cleanups and fixes.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Thu 13 May 2021 18:36:06 BST
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20210513a:
tests/migration: introduce multifd into guestperf
tests/qtest/migration-test: Use g_autofree to avoid leaks on error paths
tests/migration-test: Fix "true" vs true
migration/ram: Use offset_in_ramblock() in range checks
migration/multifd: Print used_length of memory block
migration/ram: Handle RAM block resizes during postcopy
migration/ram: Simplify host page handling in ram_load_postcopy()
migration/ram: Discard RAM when growing RAM blocks after ram_postcopy_incoming_init()
exec: Relax range check in ram_block_discard_range()
migration/ram: Handle RAM block resizes during precopy
numa: Make all callbacks of ram block notifiers optional
numa: Teach ram block notifiers about resizeable ram blocks
util: vfio-helpers: Factor out and fix processing of existing ram blocks
migration: Drop redundant query-migrate result @blocked
migration/ram: Optimize ram_save_host_page()
migration/ram: Reduce unnecessary rate limiting
migrate/ram: remove "ram_bulk_stage" and "fpo_enabled"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make add/remove optional. We want to introduce a RAM block
notifier for RAM migration that is only interested in resize events.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210429112708.12291-4-david@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Ram block notifiers are currently not aware of resizes. To properly
handle resizes during migration, we want to teach ram block notifiers about
resizeable ram.
Introduce the basic infrastructure but keep using max_size in the
existing notifiers. Supply the max_size when adding and removing ram
blocks. Also, notify on resizes.
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: xen-devel@lists.xenproject.org
Cc: haxm-team@intel.com
Cc: Paul Durrant <paul@xen.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Wenchao Wang <wenchao.wang@intel.com>
Cc: Colin Xu <colin.xu@intel.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210429112708.12291-3-david@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Factor it out into common code when a new notifier is registered, just
as done with the memory region notifier. This keeps logic about how to
process existing ram blocks at a central place.
Just like when adding a new ram block, we have to register the max_length.
Ram blocks are only "fake resized". All memory (max_length) is mapped.
Print the warning from inside qemu_vfio_ram_block_added().
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210429112708.12291-2-david@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The bulk stage is kind of weird: migration_bitmap_find_dirty() will
indicate a dirty page, however, ram_save_host_page() will never save it, as
migration_bitmap_clear_dirty() detects that it is not dirty.
We already fill the bitmap in ram_list_init_bitmaps() with ones, marking
everything dirty - it didn't used to be that way, which is why we needed
an explicit first bulk stage.
Let's simplify: make the bitmap the single source of thuth. Explicitly
handle the "xbzrle_enabled after first round" case.
Regarding XBZRLE (implicitly handled via "ram_bulk_stage = false" right
now), there is now a slight change in behavior:
- Colo: When starting, it will be disabled (was implicitly enabled)
until the first round actually finishes.
- Free page hinting: When starting, XBZRLE will be disabled (was implicitly
enabled) until the first round actually finished.
- Snapshots: When starting, XBZRLE will be disabled. We essentially only
do a single run, so I guess it will never actually get disabled.
Postcopy seems to indirectly disable it in ram_save_page(), so there
shouldn't be really any change.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210216105039.40680-1-david@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
According to the as documentation:
(https://sourceware.org/binutils/docs-2.36/as/AVR-Options.html)
"Instruction set avr51 is for the enhanced AVR core with exactly 128K
program memory space (MCU types: atmega128, atmega128a, atmega1280,
atmega1281, atmega1284, atmega1284p, atmega128rfa1, atmega128rfr2,
atmega1284rfr2, at90can128, at90usb1286, at90usb1287, m3000)."
But when compiling a program for atmega1280 or avr51 and trying to execute
it:
$ cat > test.S << EOF
> loop:
> rjmp loop
> EOF
$ avr-gcc -nostdlib -nostartfiles -mmcu=atmega1280 test.S -o test.elf
$ qemu-system-avr -serial mon:stdio -nographic -no-reboot -M mega \
-bios test.elf
qemu-system-avr: Current machine: Arduino Mega (ATmega1280) with 'avr6' CPU
qemu-system-avr: ELF image 'test.elf' is for 'avr51' CPU
So this fixes the atmega1280 class to use an avr51 CPU.
Signed-off-by: Frederic Konrad <frederic.konrad@adacore.com>
Reviewed-by: Joaquin de Andres <me@xcancerberox.com.ar>
Message-Id: <1619637319-22299-1-git-send-email-frederic.konrad@adacore.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Fixes an if statement that performs a logical AND of mutually exclusive
tests
Buglink: https://bugs.launchpad.net/qemu/+bug/1926995
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <1620402803-9237-1-git-send-email-jag.raman@oracle.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since its introduction in commit 5b85eabe68 ("acpi: add
acpi_dsdt_add_gpex") we build gpex-acpi.c if ACPI is selected,
even if the GPEX_HOST device isn't build. Add the missing
Kconfig dependency.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210425182124.3735214-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
sparse-mem.c is added to the 'mem_ss' source set, which itself
is conditionally added to softmmu_ss if CONFIG_MEM_DEVICE is
selected.
But if CONFIG_MEM_DEVICE isn't selected, we get a link failure
even if CONFIG_FUZZ is selected:
/usr/bin/ld: tests_qtest_fuzz_generic_fuzz.c.o: in function `generic_pre_fuzz':
tests/qtest/fuzz/generic_fuzz.c:826: undefined reference to `sparse_mem_init'
clang-10: error: linker command failed with exit code 1 (use -v to see invocation)
Fix by adding sparse-mem.c directly to the softmmu_ss set.
Fixes: 230376d285 ("memory: add a sparse memory device for fuzzing")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210406133944.4193691-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
TYPE_MC146818_RTC is an ISA device, so its DeviceClass::reset()
handler is called automatically when its qbus parent is reset
(we don't need to register it manually).
We have 2 reset() methods: a generic one and the qdev one.
Merge them into a reset_enter handler (keeping the IRQ lowering
to a reset_hold one), and remove the qemu_register_reset() call.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20210502163931.552675-3-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
TYPE_ETRAX_FS_TIMER is a sysbus device, so its DeviceClass::reset()
handler is called automatically when its qbus parent is reset
(we don't need to register it manually).
Convert the generic reset to a enter/hold resettable ones, and
remove the qemu_register_reset() call.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20210502163931.552675-2-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The VirtIOFeature structure isn't modified, mark it const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210511104157.2880306-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
- Clenaup some left over v1.9 code
- Documentation improvements
- Support for the shakti_c machine
- Internal cleanup of the CSR accesses
- Updates to the OpenTitan platform
- Support for the virtio-vga
- Fix for the saturate subtract in vector extensions
- Experimental support for the ePMP spec
- A range of other internal code cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmCaWaYACgkQIeENKd+X
cFS97Af/c+Zh5KddhY0qYm6/deabhzn2fPrensOX+UlQbThpbKLHPZ+ceh1GRYBl
tqfiQa6ByhLhHk4UihIjJvLL9UW+UUxR3zsUfHcFHGAmy22ms9oiGB+se37gj/YB
2WySYQhHlwW1iz+55mMh+c1wjckFFVjX4dQgh7pl60AJWxNdzNOBUr/BwMZUh0zM
UFsYDGS2MF3JId8VkW4Ui4fKTw0HBexK4gKXOsRIpF6R3+PQa3m4ppr/YZfyUy5W
o8lZhztoO5TgyGyNpCo6UdG9JlJP5iNnPRTn+ordqJhpNKFTLQeuLBW9gMpB9BiG
L1fvPePKz7GWxI/Xrl9uwNyWSYwetA==
=6TPt
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210511' into staging
A large collection of RISC-V fixes, improvements and features
- Clenaup some left over v1.9 code
- Documentation improvements
- Support for the shakti_c machine
- Internal cleanup of the CSR accesses
- Updates to the OpenTitan platform
- Support for the virtio-vga
- Fix for the saturate subtract in vector extensions
- Experimental support for the ePMP spec
- A range of other internal code cleanups and bug fixes
# gpg: Signature made Tue 11 May 2021 11:17:10 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210511: (42 commits)
target/riscv: Fix the RV64H decode comment
target/riscv: Consolidate RV32/64 16-bit instructions
target/riscv: Consolidate RV32/64 32-bit instructions
target/riscv: Remove an unused CASE_OP_32_64 macro
target/riscv: Remove the unused HSTATUS_WPRI macro
target/riscv: Remove the hardcoded SATP_MODE macro
target/riscv: Remove the hardcoded MSTATUS_SD macro
target/riscv: Remove the hardcoded HGATP_MODE macro
target/riscv: Remove the hardcoded SSTATUS_SD macro
target/riscv: Remove the hardcoded RVXLEN macro
target/riscv: fix a typo with interrupt names
fpu/softfloat: set invalid excp flag for RISC-V muladd instructions
hw/riscv: Fix OT IBEX reset vector
target/riscv: fix exception index on instruction access fault
target/riscv: fix vrgather macro index variable type bug
target/riscv: Add ePMP support for the Ibex CPU
target/riscv/pmp: Remove outdated comment
target/riscv: Add a config option for ePMP
target/riscv: Implementation of enhanced PMP (ePMP)
target/riscv: Add ePMP CSR access functions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Target unicore32 was deprecated in commit 8e4ff4a8d2, v5.2.0. See
there for rationale.
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-3-armbru@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
There are no known users of this CPU anymore, and there are no
binaries available online which could be used for regression tests,
so the code has likely completely bit-rotten already. It's been
marked as deprecated since two releases now and nobody spoke up
that there is still a need to keep it, thus let's remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210430160355.698194-1-thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Commit message typos fixed, trivial conflicts resolved]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
* i386 page walk unification
* Fix detection of gdbus-codegen
* Misc refactoring
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCblEEUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroObnQgAj10pRDODY9hIiUiYj2sTcEQTly3p
DC+ZWDaup67z3WV2C/vAS/x31RGIus+7bzji3fgtUcnGOr7sbuOCcs7CPY8mam5Y
GMPNrsUk2sZ5z9SVTq2vjEa61tjxtMpYXx9pnhgJzJAO4NJzNuX74ZdpA+oV5aTC
CvZDk8lC7BLU16MfeLcbw44xE4Oy05wWwaoP2pvhdOg47y85t/S9Il1yBCYi3y8C
pTOBBCYmHGPj/r7i4MhUGrAjIyGQu1w7av8nZXouRegoeVl28RKR8+pl7TfFpt+E
cp95yE8dPuNFJnCiZ3Kv01eBcSUcyp4gVb5H2Oa/nkkYRLpnONbUzYFtIA==
=zR5U
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging
* AccelCPUClass and sysemu/user split for i386 (Claudio)
* i386 page walk unification
* Fix detection of gdbus-codegen
* Misc refactoring
# gpg: Signature made Wed 12 May 2021 09:39:29 BST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini-gitlab/tags/for-upstream: (32 commits)
coverity-scan: list components, move model to scripts/coverity-scan
configure: fix detection of gdbus-codegen
qemu-option: support accept-any QemuOptsList in qemu_opts_absorb_qdict
main-loop: remove dead code
target/i386: use mmu_translate for NPT walk
target/i386: allow customizing the next phase of the translation
target/i386: extend pg_mode to more CR0 and CR4 bits
target/i386: pass cr3 to mmu_translate
target/i386: extract mmu_translate
target/i386: move paging mode constants from SVM to cpu.h
target/i386: merge SVM_NPTEXIT_* with PF_ERROR_* constants
accel: add init_accel_cpu for adapting accel behavior to CPU type
accel: move call to accel_init_interfaces
i386: make cpu_load_efer sysemu-only
target/i386: gdbstub: only write CR0/CR2/CR3/EFER for sysemu
target/i386: gdbstub: introduce aux functions to read/write CS64 regs
i386: split off sysemu part of cpu.c
i386: split seg_helper into user-only and sysemu parts
i386: split svm_helper into sysemu and stub-only user
i386: separate fpu_helper sysemu-only parts
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Avoid mmap race involving Xen's mapcache
- Fix xenforeignmemory_resource leak at exit
- Fix xen-block to choose a driver for the disk image when created via
xenstore.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE+AwAYwjiLP2KkueYDPVXL9f7Va8FAmCZK+QACgkQDPVXL9f7
Va+yrggA8vdfm2uRPZPKMrQ9asakyXabox9LGML7GeU5k8xVDuy38kEqWqCW4A78
L7ubiamj91KR6viHaKNPi+tlpHgJAJNXqUIqqpZoU78J0MJm1dMD4lgAHC9b/FAH
PVVHGLR5bSSon6qq+LECLlgvokLp7rCru3d/Fi3ISw8jckOPF5xhAEuX4Q8aqDsV
bk2Sic5CAn2ocHjb2gYHsOH7QZXrJwLamFGpHZjwViJTdTmmNTnZze/dPlq+24hB
QoVe1fIQOr+BUvzN1N8+1nEGMMTrY9ZVxAxuFMNejyuwyrQ5rvR+9oGiNnP1LNq/
0tm4XsNOAVTa7TUXWCAm+n0ynZWp7A==
=aOnW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/aperard/tags/pull-xen-20210510' into staging
Xen patches
- Avoid mmap race involving Xen's mapcache
- Fix xenforeignmemory_resource leak at exit
- Fix xen-block to choose a driver for the disk image when created via
xenstore.
# gpg: Signature made Mon 10 May 2021 13:49:40 BST
# gpg: using RSA key F80C006308E22CFD8A92E7980CF5572FD7FB55AF
# gpg: Good signature from "Anthony PERARD <anthony.perard@gmail.com>" [unknown]
# gpg: aka "Anthony PERARD <anthony.perard@citrix.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 5379 2F71 024C 600F 778A 7161 D8D5 7199 DF83 42C8
# Subkey fingerprint: F80C 0063 08E2 2CFD 8A92 E798 0CF5 572F D7FB 55AF
* remotes/aperard/tags/pull-xen-20210510:
xen-block: Use specific blockdev driver
xen: Free xenforeignmemory_resource at exit
xen-mapcache: avoid a race on memory map while using MAP_FIXED
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When no mapping is requested, it is pointless to create
alias regions.
Only create them when multiple mappings are requested to
simplify the memory layout. The flatview is not changed.
For example using 'qemu-system-sh4 -M r2d -S -monitor stdio',
* before:
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-0000000000ffffff (prio 0, i/o): pflash
0000000000000000-0000000000ffffff (prio 0, romd): alias pflash-alias @r2d.flash 0000000000000000-0000000000ffffff
0000000004000000-000000000400003f (prio 0, i/o): r2d-fpga
000000000c000000-000000000fffffff (prio 0, ram): r2d.sdram
(qemu) info mtree -f
FlatView #0
AS "memory", root: system
AS "cpu-memory-0", root: system
Root memory region: system
0000000000000000-0000000000ffffff (prio 0, romd): r2d.flash
0000000004000000-000000000400003f (prio 0, i/o): r2d-fpga
000000000c000000-000000000fffffff (prio 0, ram): r2d.sdram
* after:
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-0000000000ffffff (prio 0, romd): r2d.flash
0000000004000000-000000000400003f (prio 0, i/o): r2d-fpga
000000000c000000-000000000fffffff (prio 0, ram): r2d.sdram
(qemu) info mtree -f
FlatView #0
AS "memory", root: system
AS "cpu-memory-0", root: system
Root memory region: system
0000000000000000-0000000000ffffff (prio 0, romd): r2d.flash
0000000004000000-000000000400003f (prio 0, i/o): r2d-fpga
000000000c000000-000000000fffffff (prio 0, ram): r2d.sdram
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210325120921.858993-3-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The ROMD mode isn't related to mapping setup.
Ideally we'd set this mode when the state machine resets,
but for now simply move it to pflash_cfi02_realize() to
not introduce logical change.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210325120921.858993-2-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
imply VIRTIO_VGA for the virt machine, this fixes the following error
when specifying `-vga virtio` as a command line argument:
qemu-system-riscv64: Virtio VGA not available
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 7ac26fafee8bd59d2a0640f3233f8ad1ab270e1e.1617367317.git.alistair.francis@wdc.com
Update the OpenTitan interrupt layout to match the latest OpenTitan
bitstreams. This involves changing the Ibex PLIC memory layout and the
UART interrupts.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: e92b696f1809c9fa4410da2e9f23c414db5a6960.1617202791.git.alistair.francis@wdc.com
Connect one shakti uart to the shakti_c machine.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210401181457.73039-5-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is the initial implementation of Shakti UART.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210401181457.73039-4-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was accidentally dropped before. Add it back.
Fixes: 732612856a ("hw/riscv: Drop 'struct MemmapEntry'")
Reported-by: Emmanuel Blot <eblot.ml@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210331103612.654261-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
move the call for sysemu specifically in machine_run_board_init,
mirror the calling sequence for user mode too.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210322132800.7470-23-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
i386 is the first user of AccelCPUClass, allowing to split
cpu.c into:
cpu.c cpuid and common x86 cpu functionality
host-cpu.c host x86 cpu functions and "host" cpu type
kvm/kvm-cpu.c KVM x86 AccelCPUClass
hvf/hvf-cpu.c HVF x86 AccelCPUClass
tcg/tcg-cpu.c TCG x86 AccelCPUClass
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[claudio]:
Rebased on commit b8184135 ("target/i386: allow modifying TCG phys-addr-bits")
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210322132800.7470-5-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* docs: fix link in sbsa description
* linux-user/aarch64: Enable hwcap for RND, BTI, and MTE
* target/arm: Fix tlbbits calculation in tlbi_aa64_vae2is_write()
* target/arm: Split neon and vfp translation to their own
compilation units
* target/arm: Make WFI a NOP for userspace emulators
* hw/sd/omap_mmc: Use device_cold_reset() instead of
device_legacy_reset()
* include: More fixes for 'extern "C"' block use
* hw/arm/imx25_pdk: Fix error message for invalid RAM size
* hw/arm/mps2-tz: Implement AN524 memory remapping via machine property
* hw/arm/xlnx: Fix PHY address for xilinx-zynq-a9
-----BEGIN PGP SIGNATURE-----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=E7yJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210510-1' into staging
target-arm queue:
* docs: fix link in sbsa description
* linux-user/aarch64: Enable hwcap for RND, BTI, and MTE
* target/arm: Fix tlbbits calculation in tlbi_aa64_vae2is_write()
* target/arm: Split neon and vfp translation to their own
compilation units
* target/arm: Make WFI a NOP for userspace emulators
* hw/sd/omap_mmc: Use device_cold_reset() instead of
device_legacy_reset()
* include: More fixes for 'extern "C"' block use
* hw/arm/imx25_pdk: Fix error message for invalid RAM size
* hw/arm/mps2-tz: Implement AN524 memory remapping via machine property
* hw/arm/xlnx: Fix PHY address for xilinx-zynq-a9
# gpg: Signature made Mon 10 May 2021 17:26:55 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210510-1: (26 commits)
hw/arm/xlnx: Fix PHY address for xilinx-zynq-a9
hw/arm/mps2-tz: Implement AN524 memory remapping via machine property
hw/misc/mps2-scc: Support using CFG0 bit 0 for remapping
hw/misc/mps2-scc: Add "QEMU interface" comment
hw/arm/imx25_pdk: Fix error message for invalid RAM size
include/disas/dis-asm.h: Handle being included outside 'extern "C"'
include/qemu/bswap.h: Handle being included outside extern "C" block
osdep: Make os-win32.h and os-posix.h handle 'extern "C"' themselves
hw/sd/omap_mmc: Use device_cold_reset() instead of device_legacy_reset()
target/arm: Make WFI a NOP for userspace emulators
target/arm: Make translate-neon.c.inc its own compilation unit
target/arm: Make functions used by translate-neon global
target/arm: Move NeonGenThreeOpEnvFn typedef to translate.h
target/arm: Delete unused typedef
target/arm: Move vfp_reg_ptr() to translate-neon.c.inc
target/arm: Make translate-vfp.c.inc its own compilation unit
target/arm: Make functions used by translate-vfp global
target/arm: Move vfp_{load, store}_reg{32, 64} to translate-vfp.c.inc
target/arm: Move gen_aa32 functions to translate-a32.h
target/arm: Split m-nocp trans functions into their own file
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit dfc388797c ("hw/arm: xlnx: Set all boards' GEM 'phy-addr'
property value to 23") configured the PHY address for xilinx-zynq-a9
to 23. When trying to boot xilinx-zynq-a9 with zynq-zc702.dtb or
zynq-zc706.dtb, this results in the following error message when
trying to use the Ethernet interface.
macb e000b000.ethernet eth0: Could not attach PHY (-19)
The devicetree files for ZC702 and ZC706 configure PHY address 7. The
documentation for the ZC702 and ZC706 evaluation boards suggest that the
PHY address is 7, not 23. Other boards use PHY address 0, 1, 3, or 7.
I was unable to find a documentation or a devicetree file suggesting
or using PHY address 23. The Ethernet interface starts working with
zynq-zc702.dtb and zynq-zc706.dtb when setting the PHY address to 7,
so let's use it.
Cc: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210504124140.1100346-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AN524 FPGA image supports two memory maps, which differ in where
the QSPI and BRAM are. In the default map, the BRAM is at
0x0000_0000, and the QSPI at 0x2800_0000. In the second map, they
are the other way around.
In hardware, the initial mapping can be selected by the user by
writing either "REMAP: BRAM" (the default) or "REMAP: QSPI" in the
board configuration file. The board config file is acted on by the
"Motherboard Configuration Controller", which is an entirely separate
microcontroller on the dev board but outside the FPGA.
The guest can also dynamically change the mapping via the SCC
CFG_REG0 register.
Implement this functionality for QEMU, using a machine property
"remap" with valid values "BRAM" and "QSPI" to allow the user to set
the initial mapping, in the same way they can on the FPGA, and
wiring up the bit from the SCC register to also switch the mapping.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210504120912.23094-4-peter.maydell@linaro.org
On some boards, SCC config register CFG0 bit 0 controls whether
parts of the board memory map are remapped. Support this with:
* a device property scc-cfg0 so the board can specify the
initial value of the CFG0 register
* an outbound GPIO line which tracks bit 0 and which the board
can wire up to provide the remapping
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210504120912.23094-3-peter.maydell@linaro.org
The i.MX25 PDK board has 2 banks for SDRAM, each can
address up to 256 MiB. So the total RAM usable for this
board is 512M. When we ask for more we get a misleading
error message:
$ qemu-system-arm -M imx25-pdk -m 513M
qemu-system-arm: Invalid RAM size, should be 128 MiB
Update the error message to better match the reality:
$ qemu-system-arm -M imx25-pdk -m 513M
qemu-system-arm: RAM size more than 512 MiB is not supported
Fixes: bf350daae0 ("arm/imx25_pdk: drop RAM size fixup")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20210407225608.1882855-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The omap_mmc_reset() function resets its SD card via
device_legacy_reset(). We know that the SD card does not have a qbus
of its own, so the new device_cold_reset() function (which resets
both the device and its child buses) is equivalent here to
device_legacy_reset() and we can just switch to the new API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210430222348.8514-1-peter.maydell@linaro.org
... when a xen-block backend instance is created via xenstore.
Following 8d17adf34f ("block: remove support for using "file" driver
with block/char devices"), using the "file" blockdev driver for
everything doesn't work anymore, we need to use the "host_device"
driver when the disk image is a block device and "file" driver when it
is a regular file.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20210430163432.468894-1-anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Because Coverity complains about it and this is one leak that Valgrind
reports.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20210430163742.469739-1-anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
When we're replacing the existing mapping there is possibility of a race
on memory map with other threads doing mmap operations - the address being
unmapped/re-mapped could be occupied by another thread in between.
Linux mmap man page recommends keeping the existing mappings in place to
reserve the place and instead utilize the fact that the next mmap operation
with MAP_FIXED flag passed will implicitly destroy the existing mappings
behind the chosen address. This behavior is guaranteed by POSIX / BSD and
therefore is portable.
Note that it wouldn't make the replacement atomic for parallel accesses to
the replaced region - those might still fail with SIGBUS due to
xenforeignmemory_map not being atomic. So we're still not expecting those.
Tested-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <1618889702-13104-1-git-send-email-igor.druzhinin@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Introduce a symbol which can be used to prevent display modules which
need vga support being loaded into system emulators with CONFIG_VGA=n.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-16-kraxel@redhat.com>
Now that we have separated the gl and non-gl code flows to two different
devices there is little reason turn on and off virglrenderer usage at
runtime. The gl code can simply use virglrenderer unconditionally.
So drop use_virgl_renderer field and just do that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-13-kraxel@redhat.com>
Move device init (realize) and properties.
Drop the virgl property, the virtio-gpu-gl-device has virgl enabled no
matter what. Just use virtio-gpu-device instead if you don't want
enable virgl and opengl. This simplifies the logic and reduces the test
matrix.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-4-kraxel@redhat.com>
Just a skeleton for starters, following patches will add more code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-3-kraxel@redhat.com>
"3d" -> "virgl" as 3d is a rather broad term.
Hopefully a bit less confusing.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-2-kraxel@redhat.com>
dma_memory_map() may map only a part of the request. Happens if the
request can't be mapped in one go, for example due to a iommu creating
a linear dma mapping for scattered physical pages. Should that be the
case virtio-gpu must call dma_memory_map() again with the remaining
range instead of simply throwing an error.
Note that this change implies the number of iov entries may differ from
the number of mapping entries sent by the guest. Therefore the iov_len
bookkeeping needs some updates too, we have to explicitly pass around
the iov length now.
Reported-by: Auger Eric <eric.auger@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210506091001.1301250-1-kraxel@redhat.com
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210506091001.1301250-1-kraxel@redhat.com>
The Detailed Timing Descriptor has only 12 bits to store the
resolution. This limits the guest to 4095 pixels.
This patch adds support for the DisplayID extension, that has 2 full
bytes for that purpose, thus allowing 5k resolutions and above.
Based-on: <20210303152948.59943-2-akihiko.odaki@gmail.com>
Signed-off-by: Konstantin Nazarov <mail@knazarov.com>
Message-Id: <20210315114639.91953-3-mail@knazarov.com>
[ kraxel: minor workflow tweaks ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-9-kraxel@redhat.com>
Some of the EDID extensions like DisplayID do checksums of their
subsections. Currently checksums can be only applied to the whole
extension blocks which are 128 bytes.
This patch allows to checksum arbitrary parts of EDID, and not only
whole extension blocks.
Based-on: <20210303152948.59943-2-akihiko.odaki@gmail.com>
Signed-off-by: Konstantin Nazarov <mail@knazarov.com>
Message-Id: <20210315114639.91953-2-mail@knazarov.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-8-kraxel@redhat.com>
The timing generation is currently performed inside the function that
fills in the DTD. The DisplayID generation needs it as well, so moving
it out to a separate function.
Based-on: <20210303152948.59943-2-akihiko.odaki@gmail.com>
Signed-off-by: Konstantin Nazarov <mail@knazarov.com>
Message-Id: <20210315114639.91953-1-mail@knazarov.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-7-kraxel@redhat.com>
When the 4 descriptors in the base edid block are filled, jump to the
dta extension block. This allows for more than four descriptors.
Happens for example when generating an edid blob with a serial number
(qemu-edid -s $serial).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-5-kraxel@redhat.com>
Initialize the "Established timings III" block earlier. Also move up
edid_fill_modes(). That'll make sure the offset for the additional
descriptors in the dta block don't move any more, which in turn makes it
easier to actually use them.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-4-kraxel@redhat.com>
Add helper function to find the next free desc block.
Needed when we start to use the dta descriptor entries.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-3-kraxel@redhat.com>
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=N0qr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.1-20210504' into staging
ppc patch queue 2021-05-04
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
# gpg: Signature made Tue 04 May 2021 06:52:39 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210504: (46 commits)
hw/ppc/pnv_psi: Use device_cold_reset() instead of device_legacy_reset()
hw/ppc/spapr_vio: Reset TCE table object with device_cold_reset()
hw/intc/spapr_xive: Use device_cold_reset() instead of device_legacy_reset()
target/ppc: removed VSCR from SPR registration
target/ppc: Reduce the size of ppc_spr_t
target/ppc: Clean up _spr_register et al
target/ppc: Add POWER10 exception model
target/ppc: rework AIL logic in interrupt delivery
target/ppc: move opcode table logic to translate.c
target/ppc: code motion from translate_init.c.inc to gdbstub.c
spapr_drc.c: handle hotunplug errors in drc_unisolate_logical()
spapr.h: increase FDT_MAX_SIZE
spapr.c: do not use MachineClass::max_cpus to limit CPUs
ppc: Rename current DAWR macros and variables
target/ppc: POWER10 supports scv
target/ppc: Fix POWER9 radix guest HV interrupt AIL behaviour
docs/system: ppc: Add documentation for ppce500 machine
roms/u-boot: Bump ppce500 u-boot to v2021.04 to fix broken pci support
roms/Makefile: Update ppce500 u-boot build directory name
ppc/spapr: Add support for implement support for H_SCM_HEALTH
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
usb-host and usb-redirect try to batch bulk transfers by combining many
small usb packets into a single, large transfer request, to reduce the
overhead and improve performance.
This patch adds a size limit of 1 MiB for those combined packets to
restrict the host resources the guest can bind that way.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210503132915.2335822-6-kraxel@redhat.com>
-----BEGIN PGP SIGNATURE-----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=aCeG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging
Trivial patches pull request 20210503
# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
hw/rx/rx-gdbsim: Do not accept invalid memory size
docs: More precisely describe memory-backend-*::id's user
scripts: fix generation update-binfmts templates
docs/system: Document the removal of "compat" property for POWER CPUs
mc146818rtc: put it into the 'misc' category
Do not include exec/address-spaces.h if it's not really necessary
Do not include cpu.h if it's not really necessary
Do not include hw/boards.h if it's not really necessary
Do not include sysemu/sysemu.h if it's not really necessary
hw: Do not include qemu/log.h if it is not necessary
hw: Do not include hw/irq.h if it is not necessary
hw: Do not include hw/sysbus.h if it is not necessary
hw: Remove superfluous includes of hw/hw.h
ui: Fix memory leak in qemu_xkeymap_mapping_table()
hw/usb: Constify VMStateDescription
hw/display/qxl: Constify VMStateDescription
hw/arm: Constify VMStateDescription
vmstate: Constify some VMStateDescriptions
Fix typo in CFI build documentation
hw/pcmcia: Do not register PCMCIA type if not required
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since cpu_check_irqs() doesn't reference to anything outside
of CPUSPARCState, it better belongs to the architectural code
in target/, rather than the hardware specific code in hw/.
Note: while we moved the trace events, we don't rename them.
Remark: this allows us to build the leon3 machine stand alone,
fixing this link failure (because cpu_check_irqs is defined in
hw/sparc/sun4m.c which is only built when CONFIG_SUN4M is selected):
/usr/bin/ld: target_sparc_win_helper.c.o: in function `cpu_put_psr':
target/sparc/win_helper.c:91: undefined reference to `cpu_check_irqs'
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210428141655.387430-5-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
We are going to move this code, fix its style first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210428141655.387430-4-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210428141655.387430-3-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
When building without the leon3 machine, we get this link failure:
/usr/bin/ld: target_sparc_int32_helper.c.o: in function `leon3_irq_manager':
target/sparc/int32_helper.c:172: undefined reference to `leon3_irq_ack'
This is because the leon3_irq_ack() is declared in hw/sparc/leon3.c,
which is only build when CONFIG_LEON3 is selected.
Fix by moving the leon3_cache_control_int() / leon3_irq_manager()
(which are specific to the leon3 machine) to hw/sparc/leon3.c.
Move the trace events along (but don't rename them).
leon3_irq_ack() is now locally used, declare it static to reduce
its scope.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Tested-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210428141655.387430-2-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Remove the sun4m_hwdefs[] array by moving assigning the
structure fields directly in each machine class_init()
function.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210503171303.822501-7-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
We are going to move this code, fix its style first.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210503171303.822501-6-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210503171303.822501-5-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Factor out the class_init code common to all machines
to sun4m_machine_class_init().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210503171303.822501-4-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of passing the sun4m_hwdef structure via
machine_init(), store it into the MachineClass.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210503171303.822501-3-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Introduce the TYPE_SUN4M_MACHINE and have all sun4m
machines inherit it.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210503171303.822501-2-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
-----BEGIN PGP SIGNATURE-----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=N5Us
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210503' into staging
Aspeed patches :
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
# gpg: Signature made Mon 03 May 2021 06:23:36 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210503:
aspeed: Add support for the quanta-q7l1-bmc board
hw/block: m25p80: Add support for mt25ql02g and mt25qu02g
aspeed: Add support for the rainier-bmc board
aspeed: Deprecate the swift-bmc machine
tests/qtest: Rename m25p80 test in aspeed_smc test
aspeed/smc: Add extra controls to request DMA
aspeed/smc: Add a 'features' attribute to the object class
hw/misc/aspeed_xdma: Add AST2600 support
tests/acceptance: Test ast2600 machine
tests/acceptance: Test ast2400 and ast2500 machines
tests/qtest: Add test for Aspeed HACE
aspeed: Integrate HACE
hw: Model ASPEED's Hash and Crypto Engine
hw/arm/aspeed: Do not sysbus-map mmio flash region directly, use alias
aspeed/i2c: Rename DMA address space
aspeed/i2c: Fix DMA address mask
aspeed/smc: Remove unused "sdram-base" property
aspeed/smc: Use the RAM memory region for DMAs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do the same as in commit
(4d027afeb3 Virt: ACPI: fix qemu assert due to re-assigned table data address)
for remaining tables that happen to use saved at
the beginning pointer to build header to avoid assert
when table_data is relocated due to implicit re-size.
In this case user is trying to start Windows 10 and getting assert at
hw/acpi/bios-linker-loader.c:239:
bios_linker_loader_add_checksum: Assertion `start_offset < file->blob->len' failed.
Fixes: https://bugs.launchpad.net/bugs/1923497
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210414084356.3792113-1-imammedo@redhat.com>
Cc: mst@redhat.com, qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
AMD IOMMU PTEs have a special mode allowing to specify an arbitrary page
size. Quoting the AMD IOMMU specification: "When the Next Level bits [of
a pte] are 7h, the size of the page is determined by the first zero bit
in the page address, starting from bit 12."
So if the lowest bits of the page address is 0, the page is 8kB. If the
lowest bits are 011, the page is 32kB. Currently pte_override_page_mask()
doesn't compute the right value for this page size and amdvi_translate()
can return the wrong guest-physical address. With a Linux guest, DMA
from SATA devices accesses the wrong memory and causes probe failure:
qemu-system-x86_64 ... -device amd-iommu -drive id=hd1,file=foo.bin,if=none \
-device ahci,id=ahci -device ide-hd,drive=hd1,bus=ahci.0
[ 6.613093] ata1.00: qc timeout (cmd 0xec)
[ 6.615062] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
Fix the page mask.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20210421084007.1190546-1-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the Kconfig 'USB' value is not selected, it is pointless to
build the USB core components. Add a stub for the HMP commands
and usbdevice_create() which is called by usb_device_add in
softmmu/vl.c.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424224110.3442424-3-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The pnv_psi.c code uses device_legacy_reset() for two purposes:
* to reset itself from its qemu_register_reset() handler
* to reset a XiveSource object it has
Neither it nor the XiveSource have any qbuses, so the new
device_cold_reset() function (which resets both the device and its
child buses) is equivalent here to device_legacy_reset() and we can
just switch to the new API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210503151849.8766-4-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_vio_quiesce_one() function resets the TCE table object
(TYPE_SPAPR_TCE_TABLE) via device_legacy_reset(). We know that
objects of that type do not have a qbus of their own, so the new
device_cold_reset() function (which resets both the device and its
child buses) is equivalent here to device_legacy_reset() and we can
just switch to the new API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210503151849.8766-3-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The h_int_reset() function resets the XIVE interrupt controller via
device_legacy_reset(). We know that the interrupt controller does
not have a qbus of its own, so the new device_cold_reset() function
(which resets both the device and its child buses) is equivalent here
to device_legacy_reset() and we can just switch to the new API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210503151849.8766-2-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
POWER10 adds a new bit that modifies interrupt behaviour, LPCR[HAIL],
and it removes support for the LPCR[AIL]=0b10 mode.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20210501072436.145444-3-npiggin@gmail.com>
[dwg: Corrected tab indenting]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The AIL logic is becoming unmanageable spread all over powerpc_excp(),
and it is slated to get even worse with POWER10 support.
Move it all to a new helper function.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20210501072436.145444-2-npiggin@gmail.com>
[dwg: Corrected tab indenting]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At this moment, PAPR does not provide a way to report errors during a
device removal operation. This led the pSeries machine to implement
extra mechanisms to try to fallback and recover from an error that might
have happened during the hotunplug in the guest side. This started to
change a bit with commit fe1831eff8 ("spapr_drc.c: use DRC
reconfiguration to cleanup DIMM unplug state"), where one way to
fallback from a memory removal error was introduced.
Around the same time, in [1], the idea of using RTAS set-indicator for
this role was first introduced. The RTAS set-indicator call, when
attempting to UNISOLATE a DRC that is already UNISOLATED or CONFIGURED,
returns RTAS_OK and does nothing else for both QEMU and phyp. This gives
us an opportunity to use this behavior to signal the hypervisor layer
when a device removal errir happens, allowing QEMU/phyp to do a proper
error handling. Using set-indicator to report HP errors isn't strange to
PAPR, as per R1-13.5.3.4-4. of table 13.7 of current PAPR [2]:
"For all DR options: If this is a DR operation that involves the user
insert- ing a DR entity, then if the firmware can determine that the
inserted entity would cause a system disturbance, then the set-indicator
RTAS call must not unisolate the entity and must return an error status
which is unique to the particular error."
A change was proposed to the pSeries Linux kernel to call set-indicator
to move a DRC to 'unisolate' in the case of a hotunplug error in the
guest side [3]. Setting a DRC that is already unisolated or configured to
'unisolate' is a no-op (returns RTAS_OK) for QEMU and also for phyp.
Being a benign change for hypervisors that doesn't care about handling
such errors, we expect the kernel to accept this change at some point.
This patch prepares the pSeries machine for this new kernel feature by
changing drc_unisolate_logical() to handle guest side hotunplug errors.
For CPUs it's a simple matter of setting drc->unplug_requested to 'false',
while for LMBs the process is similar to the rollback that is done in
rtas_ibm_configure_connector().
[1] https://lists.gnu.org/archive/html/qemu-devel/2021-02/msg06395.html
[2] https://openpowerfoundation.org/wp-content/uploads/2020/07/LoPAR-20200611.pdf
[3] https://patchwork.ozlabs.org/project/linuxppc-dev/patch/20210416210216.380291-3-danielhb413@gmail.com/
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210420165100.108368-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Up to this patch, 'max_cpus' value is hardcoded to 1024 (commit
6244bb7e58). In theory this patch would simply bump it to 2048, since
it's the default NR_CPUS kernel setting for ppc64 servers nowadays, but
the whole mechanic of MachineClass:max_cpus is flawed for the pSeries
machine. The two supported accelerators, KVM and TCG, can live without
it.
TCG guests don't have a theoretical limit. The user must be free to
emulate as many CPUs as the hardware is capable of. And even if there
were a limit, max_cpus is not the proper way to report it since it's a
common value checked by SMP code in machine_smp_parse() for KVM as well.
For KVM guests, the proper way to limit KVM CPUs is by host
configuration via NR_CPUS, not a QEMU hardcoded value. There is no
technical reason for a pSeries QEMU guest to forcefully stay below
NR_CPUS.
This hardcoded value also disregard hosts that might have a lower
NR_CPUS limit, say 512. In this case, machine.c:machine_smp_parse() will
allow a 1024 value to pass, but then kvm_init() will complain about it
because it will exceed NR_CPUS:
Number of SMP cpus requested (1024) exceeds the maximum cpus supported
by KVM (512)
A better 'max_cpus' value would consider host settings, but
MachineClass::max_cpus is defined well before machine_init() and
kvm_init(). We can't check for KVM limits because it's too soon, so we
end up making a guess.
This patch makes MachineClass:max_cpus settings innocuous by setting it
to INT32_MAX. machine.c:machine_smp_parse() will not fail the
verification based on max_cpus, letting kvm_init() do the checking with
actual host settings. And TCG guests get to do whatever the hardware is
capable of emulating.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210408204049.221802-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add support for H_SCM_HEALTH hcall described at [1] for spapr
nvdimms. This enables guest to detect the 'unarmed' status of a
specific spapr nvdimm identified by its DRC and if its unarmed, mark
the region backed by the nvdimm as read-only.
The patch adds h_scm_health() to handle the H_SCM_HEALTH hcall which
returns two 64-bit bitmaps (health bitmap, health bitmap mask) derived
from 'struct nvdimm->unarmed' member.
Linux kernel side changes to enable handling of 'unarmed' nvdimms for
ppc64 are proposed at [2].
References:
[1] "Hypercall Op-codes (hcalls)"
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/powerpc/papr_hcalls.rst#n220
[2] "powerpc/papr_scm: Mark nvdimm as unarmed if needed during probe"
https://lore.kernel.org/linux-nvdimm/20210329113103.476760-1-vaibhav@linux.ibm.com/
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Message-Id: <20210402102128.213943-1-vaibhav@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SLOF instantiates RTAS since
744a928cce ("spapr: Stop providing RTAS blob")
so the max address applies to the FDT only.
This renames the macro and fixes up the comment.
This should not cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210331025123.29310-1-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add new machine called pegasos2 emulating the Genesi/bPlan Pegasos II,
a PowerPC board based on the Marvell MV64361 system controller and the
VIA VT8231 integrated south bridge/superio chips. It can run Linux,
AmigaOS and a wide range of MorphOS versions. Currently a firmware ROM
image is needed to boot and only MorphOS has a video driver to produce
graphics output. Linux could work too but distros that supported this
machine don't include usual video drivers so those only run with
serial console for now.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <30cbfb9cbe6f46a1e15a69a75fac45ac39340122.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Marvell Discovery II aka. MV64361 is a PowerPC system controller
chip that is used on the pegasos2 PPC board. This adds emulation of it
that models the device enough to boot guests on this board. The
mv643xx.h header with register definitions is taken from Linux 4.15.10
only fixing white space errors, removing not needed parts and changing
formatting for QEMU coding style.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <79545ebd03bfe0665b73d2d7cbc74fdf3d62629e.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add emulation of VT8231 south bridge ISA part based on the similar
VT82C686B but implemented in a separate subclass that holds the
differences while reusing parts that can be shared.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <10abc9f89854e7c980b9731c33d25a2e307e9c4f.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To allow reusing ISA bridge emulation for vt8231_isa move the device
state of vt82c686b_isa emulation in an abstract via_isa class. This
change breaks migration back compatibility but this is not an issue
for Fuloong2E machine which is not versioned or migration supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <0cb8fc69c7aaa555589181931b881335fecd2ef3.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The VT8231 south bridge is very similar to VT82C686B but there are
some differences in register addresses and functionality, e.g. the
VT8231 only has one serial port. This commit adds VT8231_SUPERIO
subclass based on the abstract VIA_SUPERIO class to emulate the
superio part of VT8231.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <8108809321f9ecf3fb1aea22ddaeccc7c3a57c8e.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Collect superio functionality and its controlling config registers
handling in an abstract VIA_SUPERIO class that is a subclass of
ISA_SUPERIO and put vt82c686b specific parts in a subclass of this
abstract class.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <fbcc8cc8baf83f327612a1ef1c14bcbcdb0e7edb.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210315184615.1985590-16-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210315184615.1985590-15-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On Mac99 and newer machines, the Uninorth PCI host bridge maps
the PCI hole region at 2GiB, so the RAM area beside 2GiB is not
accessible by the CPU. Restrict the memory to 2GiB to avoid
problems such the one reported in the buglink.
Buglink: https://bugs.launchpad.net/qemu/+bug/1922391
Reported-by: Håvard Eidnes <he@NetBSD.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210406084842.2859664-1-f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We check the amount of RAM is enough, warn when it is
not, but if so we neglect to bail out. Fix that by
adding the missing exit() call.
Fixes: bda19d7bb5 ("hw/rx: Add RX GDB simulator")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Message-Id: <20210407223056.1870497-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the mc146818rtc device is not set, put it into the 'misc'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-6-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including sysemu/sysemu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-2-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/irq.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210327050236.2232347-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/sysbus.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210327082804.2259480-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
If the Kconfig 'PCMCIA' value is not selected, it is pointless
to build the PCMCIA core components.
(Currently only one machine of the ARM targets requires this).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424222057.3434459-4-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Microdrive Compact Flash can be plugged on a PCMCIA bus.
Express the dependency using the 'depends on' Kconfig expression.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424222057.3434459-3-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Intel XScale PXA chipsets provide a PCMCIA controller,
which expose a PCMCIA bus. Express this dependency using
the Kconfig 'select' expression.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424222057.3434459-2-f4bug@amsat.org>
[lv: remove "(IDE)"]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Only the malta and loongson3-virt machines support KVM.
Restrict the other machines to TCG:
- mipssim
- magnum
- pica61
- fuloong2e
- boston
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210428170410.479308-30-f4bug@amsat.org>
Since commit 078778c5a5 ("piix4: Add an i8259 Interrupt Controller")
the TYPE_PIIX4_PCI_DEVICE exposes the ISA input IRQs as "isa" alias.
Use this alias to get IRQ for the power management PCI function.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210324182902.692419-1-f4bug@amsat.org>
The Quanta-Q71l BMC board is a board supported by OpenBMC.
Tested: Booted quanta-q71l firmware.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210416162426.3217033-1-venture@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Micron mt25ql02g is a 3V 2Gb serial NOR flash memory supporting
dual I/O and quad I/O, 4KB, 32KB, 64KB sector erase. It also supports
4B opcodes. The mt25qu02g operates at 1.8V.
https://4donline.ihs.com/images/VipMasterIC/IC/MICT/MICT-S-A0008500026/MICT-S-A0008511423-1.pdf?hkey=52A5661711E402568146F3353EA87419
Cc: Alistair Francis <alistair.francis@wdc.com>
Cc: Francisco Iglesias <francisco.iglesias@xilinx.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Rainier BMC board is a board for the middle range POWER10 IBM systems.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-19-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The SWIFT machine never came out of the lab and we already have enough
AST2500 based OpenPower machines.
Cc: Adriana Kobylak <anoo@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2600 SPI controllers have a set of bits to request/grant DMA
access. Add a new SMC feature for these controllers and use it to
check access to the DMA registers.
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-16-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It will simplify extensions of the SMC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When we introduced support for the AST2600 SoC, the XDMA controller
was forgotten. It went unnoticed because it's not used under emulation.
But the register layout being different, the reset procedure is bogus
and this breaks kexec.
Add a AspeedXDMAClass to take into account the register differences.
Cc: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Message-Id: <20210407171637.777743-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the hash and crypto engine model to the Aspeed socs.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210409000253.1475587-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The HACE (Hash and Crypto Engine) is a device that offloads MD5, SHA1,
SHA2, RSA and other cryptographic algorithms.
This initial model implements a subset of the device's functionality;
currently only MD5/SHA hashing, and on the ast2600's scatter gather
engine.
Co-developed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
[ clg: - fixes for 32-bit and OSX builds ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210409000253.1475587-2-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The flash mmio region is exposed as an AddressSpace.
AddressSpaces must not be sysbus-mapped, therefore map
the region using an alias.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[ clg : Fix DMA_FLASH_ADDR() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210312182851.1922972-3-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The RAM memory region is now used for DMAs accesses instead of the
memory address space region. Mask off the top bits of the DMA address
to reflect this change.
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407171637.777743-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Instead of passing the memory address space region, simply use the RAM
memory region instead. This simplifies RAM accesses.
This patch breaks migration compatibility.
Fixes: c4e1f0b483 ("aspeed/smc: Add support for DMAs")
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
virtio_add_queue() aborts when queue_size > VIRTQUEUE_MAX_SIZE, so
vhost_user_blk_device_realize() should check this before calling it.
Simple reproducer:
qemu-system-x86_64 \
-chardev null,id=foo \
-device vhost-user-blk-pci,queue-size=4096,chardev=foo
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1935014
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210413165654.50810-1-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently the gpex PCI controller implements no special behaviour for
guest accesses to areas of the PIO and MMIO where it has not mapped
any PCI devices, which means that for Arm you end up with a CPU
exception due to a data abort.
Most host OSes expect "like an x86 PC" behaviour, where bad accesses
like this return -1 for reads and ignore writes. In the interests of
not being surprising, make host CPU accesses to these windows behave
as -1/discard where there's no mapped PCI device.
The old behaviour generally didn't cause any problems, because
almost always the guest OS will map the PCI devices and then only
access where it has mapped them. One corner case where you will see
this kind of access is if Linux attempts to probe legacy ISA
devices via a PIO window access. So far the only case where we've
seen this has been via the syzkaller fuzzer.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210325163315.27724-1-peter.maydell@linaro.org
Fixes: https://bugs.launchpad.net/qemu/+bug/1918917
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The driver can query some bits in SMMUv3 IDR5 to learn which
translation granules are supported. Arm recommends that SMMUv3
implementations support at least 4K and 64K granules. But in
the vSMMUv3, there seems to be no reason not to support 16K
translation granule. In addition, if 16K is not supported,
vSVA will failed to be enabled in the future for 16K guest
kernel. So it'd better to support it.
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 1901b4967c changed the nvme device from using a bar exclusive
for MSI-x to sharing it on bar0.
Unfortunately, the msix_uninit_exclusive_bar() call remains in
nvme_exit() which causes havoc when the device is removed with, say,
device_del. Fix this.
Additionally, a subregion is added but it is not removed on exit which
causes a reference to linger and the drive to never be unlocked.
Fixes: 1901b4967c ("hw/block/nvme: move msix table and pba to BAR 0")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While processing SCSI i/o requests in mptsas_process_scsi_io_request(),
the Megaraid emulator appends new MPTSASRequest object 'req' to
the 's->pending' queue. In case of an error, this same object gets
dequeued in mptsas_free_request() only if SCSIRequest object
'req->sreq' is initialised. This may lead to a use-after-free issue.
Since s->pending is actually not used, simply remove it from
MPTSASState.
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reported-by: Cheolwoo Myung <cwmyung@snu.ac.kr>
Message-id: 20210419134247.1467982-1-f4bug@amsat.org
Message-Id: <20210416102243.1293871-1-mjt@msgid.tls.msk.ru>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Cheolwoo Myung <cwmyung@snu.ac.kr>
BugLink: https://bugs.launchpad.net/qemu/+bug/1914236 (CVE-2021-3392)
Fixes: e351b82611 ("hw: Add support for LSI SAS1068 (mptsas) device")
[PMD: Reworded description, added more tags]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SSE-300 has a Cortex-M55 (which was the whole reason for us
modelling it), but we forgot to actually update the code to let it
have a different CPU type from the IoTKit and SSE-200. Add CPU type
as a field for ARMSSEInfo instead of hardcoding it to always use a
Cortex-M33.
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210416104010.13228-1-peter.maydell@linaro.org
SSE-300 currently shares the SSE-200 Property array. This is
bad principally because the default values of the CPU0_FPU
and CPU0_DSP properties disable the FPU and DSP on the CPU.
That is correct for the SSE-200 but not the SSE-300.
Give the SSE-300 its own Property array with the correct
SSE-300 specific settings:
* SSE-300 has only one CPU, so no CPU1* properties
* SSE-300 CPU has FPU and DSP
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210415182353.8173-1-peter.maydell@linaro.org
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.
This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Moves the search for matching devices on an i2c bus into a separate
method. This allows for an object that owns an I2CBus can avoid
duplicating this method.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast). Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Make virtio-fs take into account server capabilities.
Just returning requested features assumes they all of then are implemented
by server and results in setting unsupported configuration if some of them
are absent.
Signed-off-by: Anton Kuchin <antonkuchin@yandex-team.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
With changes suggested by Stefan
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Here's what I hope is the last ppc related pull request for qemu-6.0.
The 2 patches here revert a behavioural change that after further
discussion we concluded was a bad idea (adding a timeout for
possibly-failed hot unplug requests). Instead it implements a
different approach to the original problem: we again let unplug
requests the guest doesn't respond to remain pending indefinitely, but
no longer allow those to block attempts to retry the same unplug
again.
The change is a bit more complex than I'd like for this late in the
freeze. Nonetheless, I think it's important to merge this for 6.0, so
we don't allow a release which has the probably-a-bad-idea timeout
behaviour.
-----BEGIN PGP SIGNATURE-----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=fIJT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210412' into staging
ppc patch queue for 2021-04-21
Here's what I hope is the last ppc related pull request for qemu-6.0.
The 2 patches here revert a behavioural change that after further
discussion we concluded was a bad idea (adding a timeout for
possibly-failed hot unplug requests). Instead it implements a
different approach to the original problem: we again let unplug
requests the guest doesn't respond to remain pending indefinitely, but
no longer allow those to block attempts to retry the same unplug
again.
The change is a bit more complex than I'd like for this late in the
freeze. Nonetheless, I think it's important to merge this for 6.0, so
we don't allow a release which has the probably-a-bad-idea timeout
behaviour.
# gpg: Signature made Mon 12 Apr 2021 06:25:58 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210412:
spapr.c: always pulse guest IRQ in spapr_core_unplug_request()
spapr: rollback 'unplug timeout' for CPU hotunplugs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When adding the Reset register in commit 5790b757cf we
forgot to migrate it.
While it is possible a VM using the PIIX4 is migrated just
after requesting a system shutdown, it is very unlikely.
However when restoring a migrated VM, we might have the
RCR bit #4 set on the stack and when the VM resume it
directly shutdowns.
Add a post_load() migration handler and set the default
RCR value to 0 for earlier versions, assuming the VM was
not going to shutdown before migration.
Fixes: 5790b757cf ("piix4: Add the Reset Control Register")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210324200334.729899-1-f4bug@amsat.org>
TYPE_VIA_PM calls apm_init() in via_pm_realize(), so
requires APM to be selected.
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Fixes: dd0ff8191a ("isa: express SuperIO dependencies with Kconfig")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210302080531.913802-1-f4bug@amsat.org>
When a CDB has been received and is about to be submitted to the SCSI layer
via one of the ESP select commands, ensure that do_cmd is set to zero before
executing the command.
Otherwise a guest executing 2 valid CDBs in quick sequence can invoke the SCSI
.transfer_data callback again before do_cmd is set to zero by the callback
function triggering an assert at the start of esp_transfer_data().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407195801.685-12-mark.cave-ayland@ilande.co.uk>
Instead let the SCSI layer invoke the .cancel callback itself to cancel and
reset the request state.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407195801.685-11-mark.cave-ayland@ilande.co.uk>
If a guest transfers the message out/command phase data using DMA with a TC
that is larger than the cmdfifo size then the cmdfifo overflows triggering
an assert. Limit the size of the transfer to the free space available in
cmdfifo.
Buglink: https://bugs.launchpad.net/qemu/+bug/1919036
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-10-mark.cave-ayland@ilande.co.uk>
If the guest tries to read a CDB using DMA and cmdfifo is not empty then it is
possible to overflow cmdfifo.
Since this can only occur by issuing deliberately incorrect instruction
sequences, ensure that the maximum length of the CDB transferred to cmdfifo is
limited to the available free space within cmdfifo.
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-9-mark.cave-ayland@ilande.co.uk>
If the guest tries to execute a CDB when cmdfifo is not empty before the start
of the message out phase then clearing the message out phase data will cause
cmdfifo to underflow due to cmdfifo_cdb_offset being larger than the amount of
data within.
Since this can only occur by issuing deliberately incorrect instruction
sequences, ensure that the maximum length of esp_fifo_pop_buf() is limited to
the size of the data within cmdfifo.
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-8-mark.cave-ayland@ilande.co.uk>
When about to execute a SCSI command, ensure that cmdfifo is not empty and
current_dev is non-NULL. This can happen if the guest tries to execute a TI
(Transfer Information) command without issuing one of the select commands
first.
Buglink: https://bugs.launchpad.net/qemu/+bug/1910723
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-7-mark.cave-ayland@ilande.co.uk>
The const pointer returned by fifo8_pop_buf() lies directly within the array used
to model the FIFO. Building with address sanitizers enabled shows that if the
caller expects a minimum number of bytes present then if the FIFO is nearly full,
the caller may unexpectedly access past the end of the array.
Introduce esp_fifo_pop_buf() which takes a destination buffer and performs a
memcpy() in it to guarantee that the caller cannot overwrite the FIFO array and
update all callers to use it. Similarly add underflow protection similar to
esp_fifo_push() and esp_fifo_pop() so that instead of triggering an assert()
the operation becomes a no-op.
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210407195801.685-6-mark.cave-ayland@ilande.co.uk>
Each FIFO currently has its own pop functions with the only difference being
the capacity check. The original reason for this was that the fifo8
implementation doesn't have a formal API for retrieving the FIFO capacity,
however there are multiple examples within QEMU where the capacity field is
accessed directly.
Change esp_fifo_pop() to access the FIFO capacity directly and then consolidate
esp_cmdfifo_pop() into esp_fifo_pop().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-5-mark.cave-ayland@ilande.co.uk>
Each FIFO currently has its own push functions with the only difference being
the capacity check. The original reason for this was that the fifo8
implementation doesn't have a formal API for retrieving the FIFO capacity,
however there are multiple examples within QEMU where the capacity field is
accessed directly.
Change esp_fifo_push() to access the FIFO capacity directly and then consolidate
esp_cmdfifo_push() into esp_fifo_push().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-4-mark.cave-ayland@ilande.co.uk>
The code for write_response() has always used the FIFO to store the data for
the status/message in phases, even for DMA transactions. Switch to using a
separate buffer that can be used directly for DMA transactions and restrict
the FIFO use to the non-DMA case.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407195801.685-3-mark.cave-ayland@ilande.co.uk>
After issuing a SCSI command the SCSI layer can call the SCSIBusInfo .cancel
callback which resets both current_req and current_dev to NULL. If any data
is left in the transfer buffer (async_len != 0) then the next TI (Transfer
Information) command will attempt to reference the NULL pointer causing a
segfault.
Buglink: https://bugs.launchpad.net/qemu/+bug/1910723
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-2-mark.cave-ayland@ilande.co.uk>
If QEMU is launched with the -S option then the ESPState mig_version_id property
is left unset due to the ordering of the VMState fields in the VMStateDescription
for sysbusespscsi and pciespscsi. If the VM is migrated and restored in this
stopped state, the version tests in the vmstate_esp VMStateDescription and
esp_post_load() become confused causing the migration to fail.
Fix the ordering problem by moving the setting of mig_version_id to a common
esp_pre_save() function which is invoked first by both sysbusespscsi and
pciespscsi rather than at the point where ESPState is itself serialised into the
migration stream.
Buglink: https://bugs.launchpad.net/qemu/+bug/1922611
Fixes: 0bd005be78 ("esp: add vmstate_esp version to embedded ESPState")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210407124842.32695-1-mark.cave-ayland@ilande.co.uk>
Each board in mps2-tz.c specifies a RAMInfo[] array providing
information about each RAM in the board. The .mpc field of the
RAMInfo struct specifies which MPC, if any, the RAM is attached to.
We already assert if the array doesn't have any entry for an MPC, but
we don't diagnose the error of using the same MPC number twice (which
is quite easy to do by accident if copy-and-pasting structure
entries).
Enhance find_raminfo_for_mpc() so that it detects multiple entries
for the MPC as well as missing entries.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-3-peter.maydell@linaro.org
The AN524 has three MPCs: one for the BRAM, one for the QSPI flash,
and one for the DDR. We incorrectly set the .mpc field in the
RAMInfo struct for the SRAM block to 1, giving it the same MPC we are
using for the QSPI. The effect of this was that the QSPI didn't get
mapped into the system address space at all, via an MPC or otherwise,
and guest programs which tried to read from the QSPI would get a bus
error. Correct the SRAM RAMInfo to indicate that it does not have an
associated MPC.
Fixes: 25ff112a8c ("hw/arm/mps2-tz: Add new mps3-an524 board")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-2-peter.maydell@linaro.org
In emulation of the CFGI_STE_RANGE command, we now take StreamID as the
start of the invalidation range, regardless of whatever the Range is,
whilst the spec clearly states that
- "Invalidation is performed for an *aligned* range of 2^(Range+1)
StreamIDs."
- "The bottom Range+1 bits of the StreamID parameter are IGNORED,
aligning the range to its size."
Take CFGI_ALL (where Range == 31) as an example, if there are some random
bits in the StreamID field, we'll fail to perform the full invalidation but
get a strange range (e.g., SMMUSIDRange={.start=1, .end=0}) instead. Rework
the emulation a bit to get rid of the discrepancy with the spec.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402100449.528-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GSIV values in SMMUv3 IORT node are not correct as they don't match
the SMMUIrq enumeration, which describes the IRQ<->PIN mapping used by
our emulated vSMMU.
Fixes: a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402084731.93-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For most commands, when issuing an AIO, the BlockAIOCB is stored in the
NvmeRequest aiocb pointer when the AIO is issued. The main use of this
is cancelling AIOs when deleting submission queues (it is currently not
used for Abort).
However, some commands like Dataset Management Zone Management Send
(zone reset) may involve more than one AIO and here the AIOs are issued
without saving a reference to the BlockAIOCB. This is a problem since
nvme_del_sq() will attempt to cancel outstanding AIOs, potentially with
an invalid BlockAIOCB since the aiocb pointer is not NULL'ed when the
request structure is recycled.
Fix this by
1. making sure the aiocb pointer is NULL'ed when requests are recycled
2. only attempt to cancel the AIO if the aiocb is non-NULL
3. if any AIOs could not be cancelled, drain all aio as a last resort.
Fixes: dc04d25e2f ("hw/block/nvme: add support for the format nvm command")
Fixes: c94973288c ("hw/block/nvme: add broadcast nsid support flush command")
Fixes: e4e430b3d6 ("hw/block/nvme: add simple copy command")
Fixes: 5f5dc4c6a9 ("hw/block/nvme: zero out zones on reset")
Fixes: 2605257a26 ("hw/block/nvme: add the dataset management command")
Cc: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Cc: Minwoo Im <minwoo.im@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
nvme_compare() fails to store the aiocb from the blk_aio_preadv() call.
Fix this.
Fixes: 0a384f923f ("hw/block/nvme: add compare command")
Cc: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
nvme_map_prp needs to calculate the number of list entries based on the
offset value. For the subsequent PRP2 list, need to ensure the number of
entries is within the MAX number of PRP entries for a page.
Signed-off-by: Padmakar Kalghatgi <p.kalghatgi@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 47c8c915b1 fixed a problem where multiple spapr_drc_detach()
requests were breaking QEMU. The solution was to just spapr_drc_detach()
once, and use spapr_drc_unplug_requested() to filter whether we already
detached it or not. The commit also tied the hotplug request to the
guest in the same condition.
Turns out that there is a reliable way for a CPU hotunplug to fail. If a
guest with one CPU hotplugs a CPU1, then offline CPU0s via 'echo 0 >
/sys/devices/system/cpu/cpu0/online', then attempts to hotunplug CPU1,
the kernel will refuse it because it's the last online CPU of the
system. Given that we're pulsing the IRQ only in the first try, in a
failed attempt, all other CPU1 hotunplug attempts will fail, regardless
of the online state of CPU1 in the kernel, because we're simply not
letting the guest know that we want to hotunplug the device.
Let's move spapr_hotplug_req_remove_by_index() back out of the "if
(!spapr_drc_unplug_requested(drc))" conditional, allowing for multiple
'device_del' requests to the same CPU core to reach the guest, in case
the CPU core didn't fully hotunplugged previously.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210401000437.131140-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries machines introduced the concept of 'unplug timeout' for CPU
hotunplugs. The idea was to circunvent a deficiency in the pSeries
specification (PAPR), that currently does not define a proper way for
the hotunplug to fail. If the guest refuses to release the CPU (see [1]
for an example) there is no way for QEMU to detect the failure.
Further discussions about how to send a QAPI event to inform about the
hotunplug timeout [2] exposed problems that weren't predicted back when
the idea was developed. Other QEMU machines don't have any type of
hotunplug timeout mechanism for any device, e.g. ACPI based machines
have a way to make hotunplug errors visible to the hypervisor. This
would make this timeout mechanism exclusive to pSeries, which is not
ideal.
The real problem is that a QAPI event that reports hotunplug timeouts
puts the management layer (namely Libvirt) in a weird spot. We're not
telling that the hotunplug failed, because we can't be 100% sure of
that, and yet we're resetting the unplug state back, preventing any
DEVICE_DEL events to reach out in case the guest decides to release the
device. Libvirt would need to inspect the guest itself to see if the
device was released or not, otherwise the internal domain states will be
inconsistent. Moreover, Libvirt already has an 'unplug timeout'
concept, and a QEMU side timeout would need to be juggled together with
the existing Libvirt timeout.
All this considered, this solution ended up creating more trouble than
it solved. This patch reverts the 3 commits that introduced the timeout
mechanism for CPU hotplugs in pSeries machines.
This reverts commit 4515a5f786
"qemu_timer.c: add timer_deadline_ms() helper"
This reverts commit d1c2e3ce3d
"spapr_drc.c: add hotunplug timeout for CPUs"
This reverts commit 51254ffb32
"spapr_drc.c: introduce unplug_timeout_timer"
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1911414
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-03/msg04682.html
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210401000437.131140-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Calling qdev_get_machine() from a QOM instance_init function is
fragile because we can't be sure the machine object actually
exists. And this happens to break when passing ",help" on the
command line to get the list of properties for a CPU core
device types :
$ ./qemu-system-ppc64 -device power8_v2.0-spapr-cpu-core,help
qemu-system-ppc64: ../../hw/core/machine.c:1290:
qdev_get_machine: Assertion `machine != NULL' failed.
Aborted (core dumped)
This used to work before QEMU 5.0, but commit 3df261b667
unwillingly introduced a subtle regression : the above command
line needs to create an instance but the instance_init function
of the base class calls qdev_get_machine() before
qemu_create_machine() has been called, which is a programming bug.
Use current_machine instead. It is okay to skip the setting of
nr_thread in this case since only its type is displayed.
Fixes: 3df261b667 ("softmmu/vl.c: Handle '-cpu help' and '-device help' before 'no default machine'")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Cc: peter.maydell@linaro.org
Message-Id: <20210409160339.500167-3-groug@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Setting the 'fallback' property corrupts the QOM instance state
(FDCtrlSysBus) because it accesses an incorrect offset (it uses
the offset of the FDCtrlISABus state).
Cc: qemu-stable@nongnu.org
Fixes: a73275dd6f ("fdc: Add fallback option")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407133742.1680424-1-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ccw_dstream_read/write functions returned values are sometime
not taking into account and reported back to the upper level
of interpretation of CCW instructions.
It follows that accessing an invalid address does not trigger
a subchannel status program check to the guest as it should.
Let's test the return values of ccw_dstream_write[_buf] and
ccw_dstream_read[_buf] and report it to the caller.
Cc: qemu-stable@nongnu.org
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <1617899529-9329-2-git-send-email-pmorel@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJgbs4gAAoJEO8Ells5jWIRvgAIAJjpj9ptxEfEAisTeU7IMNPk
vFyf9aBj/QBPv8VmcC90Mz/x38bMn0zE6V9E53camA7s1YtLxWj5ZG9wvj0ExJB9
jgk4kEm5gpj8LY7/GwECNffaITQtLZgE4HVP98dVG9o1+5iCkZf8RnXAQH2ckzTs
WoYuM0Glgj0XXdBauvpEkidQ+q23cOw7ipxNseI5wxZBAZt0RGdXoO6Dh+S219ro
kFoDwzZS9tnuwpzzZJefQJuRWkUm1LsZ6rwC7Yd+gpk2Yt+fLGihF4dc0se2+SE1
jeq7fV1E62PvEs2GJx4hs3rqakcBDE4Bf83sZnbFKMVpuvFUh+mXcKaIfXABDi8=
=3d/N
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 08 Apr 2021 10:34:24 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tap-win32: correctly recycle buffers
Revert "qapi: net: Add query-netdev command"
Revert "tests: Add tests for query-netdev command"
Revert "net: Move NetClientState.info_str to dynamic allocations"
Revert "hmp: Use QAPI NetdevInfo in hmp_info_network"
Revert "net: Do not fill legacy info_str for backends"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A seg fix in virtiofsd, a bunch of fixes for background snapshots, and
a migration test fix.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
v2
Fix for !linux build
-----BEGIN PGP SIGNATURE-----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=FKJ4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20210407b' into staging
V2 migration+virtiofs fixes pull 2021-04-07
A seg fix in virtiofsd, a bunch of fixes for background snapshots, and
a migration test fix.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
v2
Fix for !linux build
# gpg: Signature made Wed 07 Apr 2021 18:53:13 BST
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20210407b:
tests/migration: fix parameter of auto-converge migration
migration: Rename 'bs' to 'block' in background snapshot code
migration: Pre-fault memory before starting background snasphot
migration: Inhibit virtio-balloon for the duration of background snapshot
migration: Fix missing qemu_fflush() on buffer file in bg_migration_thread
virtiofsd: Fix security.capability comparison
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several issues has been reported for query-netdev info
series. Consider it's late in the rc, this reverts commit
commit 59b5437eb7.
Signed-off-by: Jason Wang <jasowang@redhat.com>
nvme_subsys_ctrl() is used in contexts where the given controller
identifier is from an untrusted source. Like its friends nvme_ns() and
nvme_subsys_ns(), nvme_subsys_ctrl() should just return NULL if an
invalid identifier is given.
Fixes: 645ce1a70c ("hw/block/nvme: support namespace attachment command")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
nvme_subsys_ns() is used in contexts where the namespace identifier is
taken from an untrusted source. Commit 3921756dee ("hw/block/nvme:
assert namespaces array indices") tried to guard against this by
introducing an assert on the namespace identifier.
This is wrong since it is perfectly valid to call the function with an
invalid namespace identifier and like nvme_ns(), nvme_subsys_ns() should
simply return NULL.
Fixes: 3921756dee ("hw/block/nvme: assert namespaces array indices")
Fixes: 94d8d6d167 ("hw/block/nvme: support allocated namespace type")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
nvme_ns_attachment() does not verify the contents of the host-supplied
16 bit "Number of Identifiers" field in the command payload.
Make sure the value is capped at 2047 and fix the out-of-bounds read.
Fixes: 645ce1a70c ("hw/block/nvme: support namespace attachment command")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add missing license/copyright headers to the nvme-dif.{c,h} files.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Prior to this patch, if a private nvme-ns device (that is, a namespace
that is not linked to a subsystem) is wired up to an nvme-subsys linked
nvme controller device, the device fails to verify that the namespace id
is unique within the subsystem. NVM Express v1.4b, Section 6.1.6 ("NSID
and Namespace Usage") states that because the device supports Namespace
Management, "NSIDs *shall* be unique within the NVM subsystem".
Additionally, prior to this patch, private namespaces are not known to
the subsystem and the namespace is considered exclusive to the
controller with which it is initially wired up to. However, this is not
the definition of a private namespace; per Section 1.6.33 ("private
namespace"), a private namespace is just a namespace that does not
support multipath I/O or namespace sharing, which means "that it is only
able to be attached to one controller at a time".
Fix this by always allocating namespaces in the subsystem (if one is
linked to the controller), regardless of the shared/private status of
the namespace. Whether or not the namespace is shareable is controlled
by a new `shared` nvme-ns parameter.
Finally, this fix allows the nvme-ns `subsys` parameter to be removed,
since the `shared` parameter now serves the purpose of attaching the
namespace to all controllers in the subsystem upon device realization.
It is invalid to have an nvme-ns namespace device with a linked
subsystem without the parent nvme controller device also being linked to
one and since the nvme-ns devices will unconditionally be "attached" (in
QEMU terms that is) to an nvme controller device through an NvmeBus, the
nvme-ns namespace device can always get a reference to the subsystem of
the controller it is explicitly (using 'bus=' parameter) or implicitly
attaching to.
Fixes: e570768566 ("hw/block/nvme: support for shared namespace in subsystem")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
The Non-MDTS DMSRL limit must be recomputed when namespaces are
detached.
Fixes: 645ce1a70c ("hw/block/nvme: support namespace attachment command")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Remove the unused BlockConf from the controller structure and remove the
noop constraint checking.
Device works just fine with both legacy drive parameter namespace and
nvme-ns namespace definitions.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
The `nvme_nsid()` function returns '-1' (FFFFFFFFh) when the given
namespace is NULL. Since FFFFFFFFh is actually a valid namespace
identifier (the "broadcast" value), change this to be '0' since that
actually *is* the invalid value.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add the missing nvme_adm_opc_str entry for the Namespace Attachment
command.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Protection Information can only be enabled if there is at least 8 bytes
of metadata.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The same thing as for incoming postcopy - we cannot deal with concurrent
RAM discards when using background snapshot feature in outgoing migration.
Fixes: 8518278a6a (migration: implementation
of background snapshot thread)
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Reported-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210401092226.102804-3-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
-----BEGIN PGP SIGNATURE-----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=f0Ad
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210406' into staging
target-arm queue:
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
# gpg: Signature made Tue 06 Apr 2021 13:25:54 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210406:
Remove myself as i.mx31 maintainer
Revert "target/arm: Make number of counters in PMCR follow the CPU"
hw/ppc/e500plat: Only try to add valid dynamic sysbus devices to platform bus
hw/arm/virt: Only try to add valid dynamic sysbus devices to platform bus
machine: Provide a function to check the dynamic sysbus allowlist
include/hw/boards.h: Document machine_class_allow_dynamic_sysbus_dev()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Two last minute bugfixes. They are both designed to prevent
compatibility headaches down the road.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmBsQkMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpUvUH/RPU/bvWjwcfjt0PSySslxleLLZX2ixZRWTl
Ij1+Ibl47Lxa5lI0ZMibac3Q4CC0+20pwGITX6165AXwMUxtHcUij+d6SW//ZrAv
rFOtAgpHGtL82ShwpWt73Qa/iZKAnl0GRaqs/gZJcFViUGPBZsDT1abG+OgI5EDh
l3+j+3CbwrZWqGygaVYNHbx/ZaO6+rq/RVxsQl6bNbP7XItanMj43NyhSngHtt7S
/UNSq9xAVSlVpCbkGqfNhms9ET4FwKoJgBK+FE2OFG5TqJoBYXKmUJx/9GML9R1d
2qwSAT9NCTniSX47mIHbcMgQZTXDkkWmvUhaSREASmlAjzoqAlQ=
=GXh7
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,virtio: last minute bugfixes
Two last minute bugfixes. They are both designed to prevent
compatibility headaches down the road.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 06 Apr 2021 12:13:07 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio-pci: compat page aligned ATS
x86: rename oem-id and oem-table-id properties
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 4c70875372 ("pci: advertise a page aligned ATS") advertises
the page aligned via ATS capability (RO) to unbrek recent Linux IOMMU
drivers since 5.2. But it forgot the compat the capability which
breaks the migration from old machine type:
(qemu) qemu-kvm: get_pci_config_device: Bad config data: i=0x104 read:
0 device: 20 cmask: ff wmask: 0 w1cmask:0
This patch introduces a new parameter "x-ats-page-aligned" for
virtio-pci device and turns it on for machine type which is newer than
5.1.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable@nongnu.org
Fixes: 4c70875372 ("pci: advertise a page aligned ATS")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210406040330.11306-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The e500plat machine device plug callback currently calls
platform_bus_link_device() for any sysbus device. This is overly
broad, because platform_bus_link_device() will unconditionally grab
the IRQs and MMIOs of the device it is passed, whether it was
intended for the platform bus or not. Restrict hotpluggability of
sysbus devices to only those devices on the dynamic sysbus allowlist.
We were mostly getting away with this because the board creates the
platform bus as the last device it creates, and so the hotplug
callback did not do anything for all the sysbus devices created by
the board itself. However if the user plugged in a device which
itself uses a sysbus device internally we would have mishandled this
and probably asserted. An example of this is:
qemu-system-ppc64 -M ppce500 -device macio-oldworld
This isn't a sensible command because the macio-oldworld device
is really specific to the 'g3beige' machine, but we now fail
with a reasonable error message rather than asserting:
qemu-system-ppc64: Device heathrow is not supported by this machine yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 20210325153310.9131-5-peter.maydell@linaro.org
The virt machine device plug callback currently calls
platform_bus_link_device() for any sysbus device. This is overly
broad, because platform_bus_link_device() will unconditionally grab
the IRQs and MMIOs of the device it is passed, whether it was
intended for the platform bus or not. Restrict hotpluggability of
sysbus devices to only those devices on the dynamic sysbus
allowlist.
We were mostly getting away with this because the board creates the
platform bus as the last device it creates, and so the hotplug
callback did not do anything for all the sysbus devices created by
the board itself. However if the user plugged in a device which
itself uses a sysbus device internally we would have mishandled this
and probably asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-4-peter.maydell@linaro.org
Provide a new function dynamic_sysbus_dev_allowed() which checks the
per-machine list of permitted dynamic sysbus devices and returns a
boolean result indicating whether the device is allowed. We can use
this in the implementation of validate_sysbus_device(), but we will
also need it so that machine hotplug callbacks can validate devices
rather than assuming that any sysbus device might be hotpluggable
into the platform bus.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-3-peter.maydell@linaro.org
The check for `n->namespace.blkconf.blk` always fails because
this is in the initialization function.
Signed-off-by: Joelle van Dyne <j@getutm.app>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The description was originally removed in commit 578d914b26
("hw/block/nvme: align zoned.zasl with mdts") together with the removal
of the zoned.append_size_limit parameter itself.
However, it was (most likely accidentally), re-added in commit
f7dcd31885 ("hw/block/nvme: add non-mdts command size limit for verify").
Remove the description again, since the parameter it describes,
zoned.append_size_limit, no longer exists.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If a device model
(a) doesn't set the value to a correct interrupt number and then
(b) triggers an interrupt for itself,
it's device model bug. Add assert on interrupt pin number to catch
this kind of bug more obviously.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <9cf8ac3b17e162daac0971d7be32deb6a33ae6ec.1616532563.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 6be8cf56bc made sure that SCI is enabled in PM1.CNT
on reset in acpi_only mode by modifying acpi_pm1_cnt_reset() and
that worked for q35 as expected.
This patch adds reset ACPI PM related registers on vt82c686 reset time
and de-assert sci.
via_pm_realize() initializes acpi pm tmr, evt, cnt and gpe.
Reset them on device reset.
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <0a3fe998525552860919a690ce83dab8f663ab99.1616532563.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 6be8cf56bc made sure that SCI is enabled in PM1.CNT
on reset in acpi_only mode by modifying acpi_pm1_cnt_reset() and
that worked for q35 as expected.
The function was introduced by commit
eaba51c573 (acpi, acpi_piix, vt82c686: factor out PM1_CNT logic)
that forgot to actually call it at piix4 reset time and as result
SCI_EN wasn't set as was expected by 6be8cf56bc in acpi_only mode.
So Windows crashes when it notices that SCI_EN is not set and FADT is
not providing information about how to enable it anymore.
Reproducer:
qemu-system-x86_64 -enable-kvm -M pc-i440fx-6.0,smm=off -cdrom any_windows_10x64.iso
Fix it by calling acpi_pm1_cnt_reset() at piix4 reset time.
Occasionally this patch adds reset acpi PM related registers on
piix4 reset time and de-assert sci.
piix4_pm_realize() initializes acpi pm tmr, evt, cnt and gpe.
Reset them on device reset. pm_reset() in ich9.c correctly calls
corresponding reset functions.
Fixes: 6be8cf56bc (acpi/core: always set SCI_EN when SMM isn't supported)
Reported-by: Reinoud Zandijk <reinoud@NetBSD.org>
Co-developed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <8a5bbd19727045ec863523830078dd4ca63f6a9a.1616532563.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The value is assigned later in this procedure.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-Id: <20210315115937.14286-3-yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1743098
This commit completes the solution of segfault in hot unplug flow
(by commit ccec7e9603).
Added missing check for vdev in virtio_pci_isr_read.
Typical stack of crash:
virtio_pci_isr_read ../hw/virtio/virtio-pci.c:1365 with proxy-vdev = 0
memory_region_read_accessor at ../softmmu/memory.c:442
access_with_adjusted_size at ../softmmu/memory.c:552
memory_region_dispatch_read1 at ../softmmu/memory.c:1420
memory_region_dispatch_read at ../softmmu/memory.c:1449
flatview_read_continue at ../softmmu/physmem.c:2822
flatview_read at ../softmmu/physmem.c:2862
address_space_read_full at ../softmmu/physmem.c:2875
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-Id: <20210315115937.14286-2-yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Qemu crashes on shutdown if the chardev used by vhost-user-blk has been
finalized before the vhost-user-blk.
This happens with char-socket chardev operating in the listening mode (server).
The char-socket chardev emits "close" event at the end of finalizing when
its internal data is destroyed. This calls vhost-user-blk event handler
which in turn tries to manipulate with destroyed chardev by setting an empty
event handler for vhost-user-blk cleanup postponing.
This patch separates the shutdown case from the cleanup postponing removing
the need to set an event handler.
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Message-Id: <20210325151217.262793-4-den-plotnikov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 4bcad76f4c ("vhost-user-blk: delay vhost_user_blk_disconnect")
introduced postponing vhost_dev cleanup aiming to eliminate qemu aborts
because of connection problems with vhost-blk daemon.
However, it introdues a new problem. Now, any communication errors
during execution of vhost_dev_init() called by vhost_user_blk_device_realize()
lead to qemu abort on assert in vhost_dev_get_config().
This happens because vhost_user_blk_disconnect() is postponed but
it should have dropped s->connected flag by the time
vhost_user_blk_device_realize() performs a new connection opening.
On the connection opening, vhost_dev initialization in
vhost_user_blk_connect() relies on s->connection flag and
if it's not dropped, it skips vhost_dev initialization and returns
with success. Then, vhost_user_blk_device_realize()'s execution flow
goes to vhost_dev_get_config() where it's aborted on the assert.
To fix the problem this patch adds immediate cleanup on device
initialization(in vhost_user_blk_device_realize()) using different
event handlers for initialization and operation introduced in the
previous patch.
On initialization (in vhost_user_blk_device_realize()) we fully
control the initialization process. At that point, nobody can use the
device since it isn't initialized and we don't need to postpone any
cleanups, so we can do cleaup right away when there is a communication
problem with the vhost-blk daemon.
On operation we leave it as is, since the disconnect may happen when
the device is in use, so the device users may want to use vhost_dev's data
to do rollback before vhost_dev is re-initialized (e.g. in vhost_dev_set_log()).
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20210325151217.262793-3-den-plotnikov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It is useful to use different connect/disconnect event handlers
on device initialization and operation as seen from the further
commit fixing a bug on device initialization.
This patch refactors the code to make use of them: we don't rely any
more on the VM state for choosing how to cleanup the device, instead
we explicitly use the proper event handler depending on whether
the device has been initialized.
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20210325151217.262793-2-den-plotnikov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the comment of tx_padding_and_crc() says: "Never add CRC in QEMU",
min_frame_len should excluce CRC, so it should be 60 instead of 64.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210316081505.72898-1-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_memory_unplug() is the last step of the hot unplug sequence.
It is indirectly called by:
spapr_lmb_release()
hotplug_handler_unplug()
and spapr_lmb_release() already buys us that DIMM unplug state is
present : it gets restored with spapr_recover_pending_dimm_state()
if missing.
g_assert() that spapr_pending_dimm_unplugs_find() cannot return NULL
in spapr_memory_unplug() to make this clear and silence Coverity.
Fixes: Coverity CID 1450767
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <161562021166.948373.15092876234470478331.stgit@bahia.lan>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Per devicetree spec v0.3 [1] chapter 2.3.5:
The #address-cells and #size-cells properties are not inherited
from ancestors in the devicetree. They shall be explicitly defined.
If missing, a client program should assume a default value of 2
for #address-cells, and a value of 1 for #size-cells.
These properties are currently missing, causing the <reg> property
of the queue-group subnode to be incorrectly parsed using default
values.
[1] https://github.com/devicetree-org/devicetree-specification/releases/download/v0.3/devicetree-specification-v0.3.pdf
Fixes: fdfb7f2cdb ("e500: Add support for eTSEC in device tree")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210311081608.66891-1-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In commit 81b3ddaf87 we fixed a use of uninitialized data
in read_tcnt(). However this change wasn't enough to placate
Coverity, which is not smart enough to see that if we read a
2 bit field and then handle cases 0, 1, 2 and 3 then there cannot
be a flow of execution through the switch default. Add explicit
default cases which assert that they can't be reached, which
should help silence Coverity.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210319162458.13760-1-peter.maydell@linaro.org
They were introduced in commit 9bde7f0674 ("hw/arm/smmuv3: Implement
translate callback") but never actually used. Drop them.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325142702.790-1-yuzenghui@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When building with --enable-sanitizers we get:
Direct leak of 16 byte(s) in 1 object(s) allocated from:
#0 0x5618479ec7cf in malloc (qemu-system-aarch64+0x233b7cf)
#1 0x7f675745f958 in g_malloc (/lib64/libglib-2.0.so.0+0x58958)
#2 0x561847c2dcc9 in xlnx_dp_init hw/display/xlnx_dp.c:1259:5
#3 0x56184a5bdab8 in object_init_with_type qom/object.c:375:9
#4 0x56184a5a2bda in object_initialize_with_type qom/object.c:517:5
#5 0x56184a5a24d5 in object_initialize qom/object.c:536:5
#6 0x56184a5a2f6c in object_initialize_child_with_propsv qom/object.c:566:5
#7 0x56184a5a2e60 in object_initialize_child_with_props qom/object.c:549:10
#8 0x56184a5a3a1e in object_initialize_child_internal qom/object.c:603:5
#9 0x5618495aa431 in xlnx_zynqmp_init hw/arm/xlnx-zynqmp.c:273:5
The RX/TX FIFOs are created in xlnx_dp_init(), add xlnx_dp_finalize()
to destroy them.
Fixes: 58ac482a66 ("introduce xlnx-dp")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210323182958.277654-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Max noticed that since blk_aio_pwrite_zeroes() may invoke the callback
before returning, the callbacks will never see *count == 0 and thus
never free the count variable or decrement num_formats causing a CQE to
never be posted.
Coverity (CID 1451082) also picked up on the fact that count would not
be free'ed if the namespace was of zero size.
Fix both of these issues by explicitly checking *count and finalize for
the given namespace if --(*count) is zero. Enqueing a CQE if there are
no AIOs outstanding after this case is already handled by nvme_format()
by inspecting *num_formats.
Reported-by: Max Reitz <mreitz@redhat.com>
Reported-by: Coverity (CID 1451082)
Fixes: dc04d25e2f ("hw/block/nvme: add support for the format nvm command")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
If nvme_map_dptr() fails, nvme_dif_rw() will leak the bounce context.
Fix this by using the same error handling as everywhere else in the
function.
Reported-by: Coverity (CID 1451080)
Fixes: 146f720c55 ("hw/block/nvme: end-to-end data protection")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
QEMU crashes with certain targets when trying to show the help
output of EHCI devices:
$ ./qemu-system-aarch64 -device ich9-usb-ehci1,help
qemu-system-aarch64: ../../devel/qemu/softmmu/physmem.c:1154: phys_section_add:
Assertion `map->sections_nb < TARGET_PAGE_SIZE' failed.
Aborted (core dumped)
This happens because the device is doing things at "instance_init" time
that should be done at "realize" time instead. So move the related code
to the realize() function instead. (NB: This now also matches the
memory_region_del_subregion() calls which are done in usb_ehci_unrealize(),
and not during finalize()).
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210326095155.1994604-1-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since the virtio-gpu-ccw device depends on the hw-display-virtio-gpu
module, which provides the type virtio-gpu-device, packaging the
hw-display-virtio-gpu module as a separate package that may or may not
be installed along with the qemu package leads to problems. Namely if
the hw-display-virtio-gpu is absent, qemu continues to advertise
virtio-gpu-ccw, but it aborts not only when one attempts using
virtio-gpu-ccw, but also when libvirtd's capability probing tries
to instantiate the type to introspect it.
Let us thus introduce a module named hw-s390x-virtio-gpu-ccw that
is going to provide the virtio-gpu-ccw device. The hw-s390x prefix
was chosen because it is not a portable device.
With virtio-gpu-ccw built as a module, the correct way to package a
modularized qemu is to require that hw-display-virtio-gpu must be
installed whenever the module hw-s390x-virtio-gpu-ccw.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210317095622.2839895-4-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Introduce a symbol which can be used to prevent ccw modules
being loaded into system emulators without ccw support.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210317095622.2839895-3-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When building with --enable-sanitizers we get:
Direct leak of 32 byte(s) in 2 object(s) allocated from:
#0 0x5618479ec7cf in malloc (qemu-system-aarch64+0x233b7cf)
#1 0x7f675745f958 in g_malloc (/lib64/libglib-2.0.so.0+0x58958)
#2 0x561847f02ca2 in usb_packet_init hw/usb/core.c:531:5
#3 0x561848df4df4 in usb_ehci_init hw/usb/hcd-ehci.c:2575:5
#4 0x561847c119ac in ehci_sysbus_init hw/usb/hcd-ehci-sysbus.c:73:5
#5 0x56184a5bdab8 in object_init_with_type qom/object.c:375:9
#6 0x56184a5bd955 in object_init_with_type qom/object.c:371:9
#7 0x56184a5a2bda in object_initialize_with_type qom/object.c:517:5
#8 0x56184a5a24d5 in object_initialize qom/object.c:536:5
#9 0x56184a5a2f6c in object_initialize_child_with_propsv qom/object.c:566:5
#10 0x56184a5a2e60 in object_initialize_child_with_props qom/object.c:549:10
#11 0x56184a5a3a1e in object_initialize_child_internal qom/object.c:603:5
#12 0x561849542d18 in npcm7xx_init hw/arm/npcm7xx.c:427:5
Similarly to commit d710e1e7bd ("usb: ehci: fix memory leak in
ehci"), fix by calling usb_ehci_finalize() to free the USBPacket.
Fixes: 7341ea075c
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210323183701.281152-1-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
"-usbdevice ccid" was not documented and -usbdevice itself was marked
as deprecated before QEMU v6.0. And searching for "-usbdevice ccid"
in the internet does not show any useful results, so likely nobody
was using the ccid device via the -usbdevice option. Remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210311092829.1479051-1-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This PR includes:
- Fix for vector CSR access
- Improvements to the Ibex UART device
- PMP improvements and bug fixes
- Hypervisor extension bug fixes
- ramfb support for the virt machine
- Fast read support for SST flash
- Improvements to the microchip_pfsoc machine
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmBZSuUACgkQIeENKd+X
cFQfqggAqiTI/KYe5GW9WBrPpGdctuEgUVBbxUhq5zY52mVGTfqEn4LbCfvdaTOp
O1MA+kfi4JN87VVWCfHPH0S725qmaPV7wfpWKi8KcPQ9uR+4RvjX/RDptkZhVjC9
Ok9p6dg2cUbz9Jm/q2V1Z69fRNMrz6pJWPxfZeTpy9bcmFNyYBR9+xiSXaW2fuAM
HsyZbsP8zHmHxfGcZwI6vpSZh3P4Ytd6nL/8v98i1DwWUsf51TsEwaS87gRQSjTz
SHqHZ9xsVM0k3glFi+El39iHzpujlONkYPvZaFP8kRhzXtaWVP1cu+CaKNUPEteq
jWNHLwFQk9VcN8uDG5o0unGEXnLJPA==
=dKa4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210322-2' into staging
RISC-V PR for 6.0
This PR includes:
- Fix for vector CSR access
- Improvements to the Ibex UART device
- PMP improvements and bug fixes
- Hypervisor extension bug fixes
- ramfb support for the virt machine
- Fast read support for SST flash
- Improvements to the microchip_pfsoc machine
# gpg: Signature made Tue 23 Mar 2021 01:56:53 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210322-2:
target/riscv: Prevent lost illegal instruction exceptions
docs/system: riscv: Add documentation for 'microchip-icicle-kit' machine
hw/riscv: microchip_pfsoc: Map EMMC/SD mux register
hw/block: m25p80: Support fast read for SST flashes
target/riscv: Add proper two-stage lookup exception detection
target/riscv: Fix read and write accesses to vsip and vsie
hw/riscv: allow ramfb on virt
hw/riscv: Add fw_cfg support to virt
target/riscv: Use background registers also for MSTATUS_MPV
target/riscv: Make VSTIP and VSEIP read-only in hip
target/riscv: Adjust privilege level for HLV(X)/HSV instructions
target/riscv: flush TLB pages if PMP permission has been changed
target/riscv: add log of PMP permission checking
target/riscv: propagate PMP permission to TLB page
hw/char: disable ibex uart receive if the buffer is full
target/riscv: fix vs() to return proper error code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For accesses to rom blob data before or during reset, we have a
function rom_ptr() which looks for a rom blob that would be loaded to
the specified address, and returns a pointer into the rom blob data
corresponding to that address. This allows board or CPU code to say
"what is the data that is going to be loaded to this address?".
However, this function does not take account of memory region
aliases. If for instance a machine model has RAM at address
0x0000_0000 which is aliased to also appear at 0x1000_0000, a
rom_ptr() query for address 0x0000_0000 will only return a match if
the guest image provided by the user was loaded at 0x0000_0000 and
not if it was loaded at 0x1000_0000, even though they are the same
RAM and a run-time guest CPU read of 0x0000_0000 will read the data
loaded to 0x1000_0000.
Provide a new function rom_ptr_for_as() which takes an AddressSpace
argument, so that it can check whether the MemoryRegion corresponding
to the address is also mapped anywhere else in the AddressSpace and
look for rom blobs that loaded to that alias.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210318174823.18066-5-peter.maydell@linaro.org
A clock is added by commit aac63e0e6e ("hw/char/pl011: add a clock
input") since v5.2.0 which corresponds to virt-5.2 machine type. It
causes backwards migration failure from upstream to downstream (v5.1.0)
when the machine type is specified with virt-5.1.
This fixes the issue by following instructions from section "Connecting
subsections to properties" in docs/devel/migration.rst. With this applied,
the PL011 clock is migrated based on the machine type.
virt-5.2 or newer: migration
virt-5.1 or older: non-migration
Cc: qemu-stable@nongnu.org # v5.2.0+
Fixes: aac63e0e6e ("hw/char/pl011: add a clock input")
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20210318023801.18287-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Windows guests using the "Basic Display Adapter" don't parse the
"Established timings III" block. They also don't parse any edid
extension.
So prefer the "Standard Timings" block to store the display resolutions
in edid_fill_modes(). Also reorder the mode list, so more exotic
resolutions (specifically the ones which are not supported by vgabios)
are moved down and the remaining ones have a better chance to get one of
the eight slots in the "Standard Timings" block.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210316143812.2363588-6-kraxel@redhat.com>
Whenever a Xen block device is detach via xenstore, the image
associated with it remained open by the backend QEMU and an error is
logged:
qemu-system-i386: failed to destroy drive: Node xvdz-qcow2 is in use
This happened since object_unparent() doesn't immediately frees the
object and thus keep a reference to the node we are trying to free.
The reference is hold by the "drive" property and the call
xen_block_drive_destroy() fails.
In order to fix that, we call drain_call_rcu() to run the callback
setup by bus_remove_child() via object_unparent().
Fixes: 2d24a64661 ("device-core: use RCU for list of children of a bus")
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20210308143232.83388-1-anthony.perard@citrix.com>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per SST25VF016B datasheet [1], SST flash requires a dummy byte after
the address bytes. Note only SPI mode is supported by SST flashes.
[1] http://ww1.microchip.com/downloads/en/devicedoc/s71271_04.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210306060152.7250-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Not disabling the UART leads to QEMU overwriting the UART receive buffer with
the newest received byte. The rx_level variable is added to allow the use of
the existing OpenTitan driver libraries.
Signed-off-by: Alexander Wagner <alexander.wagner@ulal.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210309152130.13038-1-alexander.wagner@ulal.de
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The code that sets/gets oem fields is duplicated in both PC and MICROVM
variants. This commit moves it to X86MachineState so that all x86
variants can use it and duplication is removed.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210221001737.24499-2-posteuca@mutex.one>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's also set a maximum size for "etc/acpi/rsdp", so the maximum
size doesn't get implicitly set based on the initial table size. In my
experiments, the table size was in the range of 22 bytes, so a single
page (== what we used until now) seems to be good enough.
Now that we have defined maximum sizes for all currently used table types,
let's assert that we catch usage with new tables that need a proper maximum
size definition.
Also assert that our initial size does not exceed the maximum size; while
qemu_ram_alloc_internal() properly asserts that the initial RAMBlock size
is <= its maximum size, the result might differ when the host page size
is bigger than 4k.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-5-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We want to have safety margins for all tables based on the table type.
Let's move the maximum size logic into acpi_add_rom_blob() and make it
dependent on the table name, so we don't have to replicate for each and
every instance that creates such tables.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-4-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's just reuse ACPI_BUILD_LOADER_FILE.
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-3-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resizeable memory region / RAMBlock that is created for the cmd blob
has a maximum size of whole host pages (e.g., 4k), because RAMBlocks
work on full host pages. In addition, in i386 ACPI code:
acpi_align_size(tables->linker->cmd_blob, ACPI_BUILD_ALIGN_SIZE);
makes sure to align to multiples of 4k, padding with 0.
For example, if our cmd_blob is created with a size of 2k, the maximum
size is 4k - we cannot grow beyond that. Growing might be required
due to guest action when rebuilding the tables, but also on incoming
migration.
This automatic generation of the maximum size used to be sufficient,
however, there are cases where we cross host pages now when growing at
runtime: we exceed the maximum size of the RAMBlock and can crash QEMU when
trying to resize the resizeable memory region / RAMBlock:
$ build/qemu-system-x86_64 --enable-kvm \
-machine q35,nvdimm=on \
-smp 1 \
-cpu host \
-m size=2G,slots=8,maxmem=4G \
-object memory-backend-file,id=mem0,mem-path=/tmp/nvdimm,size=256M \
-device nvdimm,label-size=131072,memdev=mem0,id=nvdimm0,slot=1 \
-nodefaults \
-device vmgenid \
-device intel-iommu
Results in:
Unexpected error in qemu_ram_resize() at ../softmmu/physmem.c:1850:
qemu-system-x86_64: Size too large: /rom@etc/table-loader:
0x2000 > 0x1000: Invalid argument
In this configuration, we consume exactly 4k (32 entries, 128 bytes each)
when creating the VM. However, once the guest boots up and maps the MCFG,
we also create the MCFG table and end up consuming 2 additional entries
(pointer + checksum) -- which is where we try resizing the memory region
/ RAMBlock, however, the maximum size does not allow for it.
Currently, we get the following maximum sizes for our different
mutable tables based on behavior of resizeable RAMBlock:
hw table max_size
------- ---------------------------------------------------------
virt "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
virt "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
virt "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
i386 "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
microvm "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
Let's set the maximum table size for "etc/table-loader" to 64k, so we
can properly grow at runtime, which should be good enough for the future.
Migration is not concerned with the maximum size of a RAMBlock, only
with the used size - so existing setups are not affected. Of course, we
cannot migrate a VM that would have crash when started on older QEMU from
new QEMU to older QEMU without failing early on the destination when
synchronizing the RAM state:
qemu-system-x86_64: Size too large: /rom@etc/table-loader: 0x2000 > 0x1000: Invalid argument
qemu-system-x86_64: error while loading state for instance 0x0 of device 'ram'
qemu-system-x86_64: load of migration failed: Invalid argument
We'll refactor the code next, to make sure we get rid of this implicit
behavior for "etc/acpi/rsdp" as well and to make the code easier to
grasp.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-2-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement _DSM according to:
PCI Firmware Specification 3.1
4.6.7. DSM for Naming a PCI or PCI Express Device Under
Operating Systems
and wire it up to cold and hot-plugged PCI devices.
Feature depends on ACPI hotplug being enabled (as that provides
PCI devices descriptions in ACPI and MMIO registers that are
reused to fetch acpi-index).
acpi-index should work for
- cold plugged NICs:
$QEMU -device e1000,acpi-index=100
=> 'eno100'
- hot-plugged
(monitor) device_add e1000,acpi-index=200,id=remove_me
=> 'eno200'
- re-plugged
(monitor) device_del remove_me
(monitor) device_add e1000,acpi-index=1
=> 'eno1'
Windows also sees index under "PCI Label Id" field in properties
dialog but otherwise it doesn't seem to have any effect.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be used by follow up patches
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it helps to avoid device naming conflicts when guest OS is
configured to use acpi-index for naming.
Spec ialso says so:
PCI Firmware Specification Revision 3.2
4.6.7. _DSM for Naming a PCI or PCI Express Device Under Operating Systems
"
Instance number must be unique under \_SB scope. This instance number does not have to
be sequential in a given system configuration.
"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In x86/ACPI world, linux distros are using predictable
network interface naming since systemd v197. Which on
QEMU based VMs results into path based naming scheme,
that names network interfaces based on PCI topology.
With itm on has to plug NIC in exactly the same bus/slot,
which was used when disk image was first provisioned/configured
or one risks to loose network configuration due to NIC being
renamed to actually used topology.
That also restricts freedom to reshape PCI configuration of
VM without need to reconfigure used guest image.
systemd also offers "onboard" naming scheme which is
preferred over PCI slot/topology one, provided that
firmware implements:
"
PCI Firmware Specification 3.1
4.6.7. DSM for Naming a PCI or PCI Express Device Under
Operating Systems
"
that allows to assign user defined index to PCI device,
which systemd will use to name NIC. For example, using
-device e1000,acpi-index=100
guest will rename NIC to 'eno100', where 'eno' is default
prefix for "onboard" naming scheme. This doesn't require
any advance configuration on guest side to com in effect
at 'onboard' scheme takes priority over path based naming.
Hope is that 'acpi-index' it will be easier to consume by
management layer, compared to forcing specific PCI topology
and/or having several disk image templates for different
topologies and will help to simplify process of spawning
VM from the same template without need to reconfigure
guest NIC.
This patch adds, 'acpi-index'* property and wires up
a 32bit register on top of pci hotplug register block
to pass index value to AML code at runtime.
Following patch will add corresponding _DSM code and
wire it up to PCI devices described in ACPI.
*) name comes from linux kernel terminology
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the block size is programmed to a different value from the
previous one, reset the data pointer of s->fifo_buffer[] so that
s->fifo_buffer[] can be filled in using the new block size in
the next transfer.
With this fix, the following reproducer:
outl 0xcf8 0x80001010
outl 0xcfc 0xe0000000
outl 0xcf8 0x80001001
outl 0xcfc 0x06000000
write 0xe000002c 0x1 0x05
write 0xe0000005 0x1 0x02
write 0xe0000007 0x1 0x01
write 0xe0000028 0x1 0x10
write 0x0 0x1 0x23
write 0x2 0x1 0x08
write 0xe000000c 0x1 0x01
write 0xe000000e 0x1 0x20
write 0xe000000f 0x1 0x00
write 0xe000000c 0x1 0x32
write 0xe0000004 0x2 0x0200
write 0xe0000028 0x1 0x00
write 0xe0000003 0x1 0x40
cannot be reproduced with the following QEMU command line:
$ qemu-system-x86_64 -nographic -machine accel=qtest -m 512M \
-nodefaults -device sdhci-pci,sd-spec-version=3 \
-drive if=sd,index=0,file=null-co://,format=raw,id=mydrive \
-device sd-card,drive=mydrive -qtest stdio
Cc: qemu-stable@nongnu.org
Fixes: CVE-2020-17380
Fixes: CVE-2020-25085
Fixes: CVE-2021-3409
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cornelius Aschermann (Ruhr-Universität Bochum)
Reported-by: Sergej Schumilo (Ruhr-Universität Bochum)
Reported-by: Simon Wörner (Ruhr-Universität Bochum)
Buglink: https://bugs.launchpad.net/qemu/+bug/1892960
Buglink: https://bugs.launchpad.net/qemu/+bug/1909418
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1928146
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The codes to limit the maximum block size is only necessary when
SDHC_BLKSIZE register is writable.
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When an ADMA transfer is started, the codes forget to set the
controller status to indicate a transfer is in progress.
With this fix, the following 2 reproducers:
https://paste.debian.net/plain/1185136https://paste.debian.net/plain/1185141
cannot be reproduced with the following QEMU command line:
$ qemu-system-x86_64 -nographic -machine accel=qtest -m 512M \
-nodefaults -device sdhci-pci,sd-spec-version=3 \
-drive if=sd,index=0,file=null-co://,format=raw,id=mydrive \
-device sd-card,drive=mydrive -qtest stdio
Cc: qemu-stable@nongnu.org
Fixes: CVE-2020-17380
Fixes: CVE-2020-25085
Fixes: CVE-2021-3409
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cornelius Aschermann (Ruhr-Universität Bochum)
Reported-by: Sergej Schumilo (Ruhr-Universität Bochum)
Reported-by: Simon Wörner (Ruhr-Universität Bochum)
Buglink: https://bugs.launchpad.net/qemu/+bug/1892960
Buglink: https://bugs.launchpad.net/qemu/+bug/1909418
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1928146
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At the end of sdhci_send_command(), it starts a data transfer if the
command register indicates data is associated. But the data transfer
should only be initiated when the command execution has succeeded.
With this fix, the following reproducer:
outl 0xcf8 0x80001810
outl 0xcfc 0xe1068000
outl 0xcf8 0x80001804
outw 0xcfc 0x7
write 0xe106802c 0x1 0x0f
write 0xe1068004 0xc 0x2801d10101fffffbff28a384
write 0xe106800c 0x1f 0x9dacbbcad9e8f7061524334251606f7e8d9cabbac9d8e7f60514233241505f
write 0xe1068003 0x28 0x80d000251480d000252280d000253080d000253e80d000254c80d000255a80d000256880d0002576
write 0xe1068003 0x1 0xfe
cannot be reproduced with the following QEMU command line:
$ qemu-system-x86_64 -nographic -M pc-q35-5.0 \
-device sdhci-pci,sd-spec-version=3 \
-drive if=sd,index=0,file=null-co://,format=raw,id=mydrive \
-device sd-card,drive=mydrive \
-monitor none -serial none -qtest stdio
Cc: qemu-stable@nongnu.org
Fixes: CVE-2020-17380
Fixes: CVE-2020-25085
Fixes: CVE-2021-3409
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cornelius Aschermann (Ruhr-Universität Bochum)
Reported-by: Sergej Schumilo (Ruhr-Universität Bochum)
Reported-by: Simon Wörner (Ruhr-Universität Bochum)
Buglink: https://bugs.launchpad.net/qemu/+bug/1892960
Buglink: https://bugs.launchpad.net/qemu/+bug/1909418
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1928146
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210303122639.20004-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the sd_erase() does not erase the requested range of card
data to 0xFFs. Let's make the erase operation actually happen.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <1613811493-58815-1-git-send-email-bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
"qemu-common.h" should be included to provide the forward declaration
of qemu_hexdump() when DEBUG_SD is on.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210228050609.24779-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
ret in virtio_pmem_resp is a uint32_t variable, which should be assigned
using virtio_stl_p.
The kernel side driver does not guarantee virtio_pmem_resp to be initialized
to zero in advance, So sometimes the flush operation will fail.
Signed-off-by: Wang Liang <wangliangzz@inspur.com>
Message-Id: <20210317024145.271212-1-wangliangzz@126.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that everything is in place, have the nested event loop to monitor
the slave channel. The source in the main event loop is destroyed and
recreated to ensure any pending even for the slave channel that was
previously detected is purged. This guarantees that the main loop
wont invoke slave_read() based on an event that was already handled
by the nested loop.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210312092212.782255-7-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
A deadlock condition potentially exists if a vhost-user process needs
to request something to QEMU on the slave channel while processing a
vhost-user message.
This doesn't seem to affect any vhost-user implementation so far, but
this is currently biting the upcoming enablement of DAX with virtio-fs.
The issue is being observed when the guest does an emergency reboot while
a mapping still exits in the DAX window, which is very easy to get with
a busy enough workload (e.g. as simulated by blogbench [1]) :
- QEMU sends VHOST_USER_GET_VRING_BASE to virtiofsd.
- In order to complete the request, virtiofsd then asks QEMU to remove
the mapping on the slave channel.
All these dialogs are synchronous, hence the deadlock.
As pointed out by Stefan Hajnoczi:
When QEMU's vhost-user master implementation sends a vhost-user protocol
message, vhost_user_read() does a "blocking" read during which slave_fd
is not monitored by QEMU.
The natural solution for this issue is an event loop. The main event
loop cannot be nested though since we have no guarantees that its
fd handlers are prepared for re-entrancy.
Introduce a new event loop that only monitors the chardev I/O for now
in vhost_user_read() and push the actual reading to a one-shot handler.
A subsequent patch will teach the loop to monitor and process messages
from the slave channel as well.
[1] https://github.com/jedisct1/Blogbench
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210312092212.782255-6-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The slave channel is implemented with socketpair() : QEMU creates
the pair, passes one of the socket to virtiofsd and monitors the
other one with the main event loop using qemu_set_fd_handler().
In order to fix a potential deadlock between QEMU and a vhost-user
external process (e.g. virtiofsd with DAX), we want to be able to
monitor and service the slave channel while handling vhost-user
requests.
Prepare ground for this by converting the slave channel to be a
QIOChannelSocket. This will make monitoring of the slave channel
as simple as calling qio_channel_add_watch_source(). Since the
connection is already established between the two sockets, only
incoming I/O (G_IO_IN) and disconnect (G_IO_HUP) need to be
serviced.
This also allows to get rid of the ancillary data parsing since
QIOChannelSocket can do this for us. Note that the MSG_CTRUNC
check is dropped on the way because QIOChannelSocket ignores this
case. This isn't a problem since slave_read() provisions space for
8 file descriptors, but affected vhost-user slave protocol messages
generally only convey one. If for some reason a buggy implementation
passes more file descriptors, no need to break the connection, just
like we don't break it if some other type of ancillary data is
received : this isn't explicitely violating the protocol per-se so
it seems better to ignore it.
The current code errors out on short reads and writes. Use the
qio_channel_*_all() variants to address this on the way.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210312092212.782255-5-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210312092212.782255-4-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Some message types, e.g. VHOST_USER_SLAVE_VRING_HOST_NOTIFIER_MSG,
can convey file descriptors. These must be closed before returning
from slave_read() to avoid being leaked. This can currently be done
in two different places:
[1] just after the request has been processed
[2] on the error path, under the goto label err:
These path are supposed to be mutually exclusive but they are not
actually. If the VHOST_USER_NEED_REPLY_MASK flag was passed and the
sending of the reply fails, both [1] and [2] are performed with the
same descriptor values. This can potentially cause subtle bugs if one
of the descriptor was recycled by some other thread in the meantime.
This code duplication complicates rollback for no real good benefit.
Do the closing in a unique place, under a new fdcleanup: goto label
at the end of the function.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210312092212.782255-3-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
slave_read() checks EAGAIN when reading or writing to the socket
fails. This gives the impression that the slave channel is in
non-blocking mode, which is certainly not the case with the current
code base. And the rest of the code isn't actually ready to cope
with non-blocking I/O.
Just drop the checks everywhere in this function for the sake of
clarity.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210312092212.782255-2-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Both functions don't check the personality of the interface (legacy or
modern) before accessing the configuration memory and always use
virtio_config_readX()/virtio_config_writeX().
With this patch, they now check the personality and in legacy mode
call virtio_config_readX()/virtio_config_writeX(), otherwise call
virtio_config_modern_readX()/virtio_config_modern_writeX().
This change has been tested with virtio-mmio guests (virt stretch/armhf and
virt sid/m68k) and virtio-pci guests (pseries RHEL-7.3/ppc64 and /ppc64le).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210314200300.3259170-1-laurent@vivier.eu>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For virtio-net, there is no need to pad the Ethernet frame size to
60 bytes before sending to it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
The previous commit rendered the name fdctrl_connect_drives() somewhat
misleading. Get rid of it by inlining the (now pretty simple)
function into its only caller.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20210309161214.1402527-4-armbru@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Drop the crap deprecated in commit 4a27a638e7 "fdc: Deprecate
configuring floppies with -global isa-fdc" (v5.1.0).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20210309161214.1402527-3-armbru@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Some compiler versions are smart enough to detect a potentially
uninitialized variable, but are not smart enough to detect that this
cannot happen due to the code flow:
../hw/intc/i8259.c: In function ‘pic_read_irq’:
../hw/intc/i8259.c:203:13: error: ‘irq2’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
203 | irq = irq2 + 8;
| ~~~~^~~~~~~~~~
Restrict irq2 variable use to the inner statement.
Fixes: 78ef2b6989 ("i8259: Reorder intack in pic_read_irq")
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210318163059.3686596-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- QAPIfy object-add and --object
- stream: Fail gracefully if permission is denied
- storage-daemon: Fix crash on quit when job is still running
- curl: Fix use after free
- char: Deprecate backend aliases, fix QMP query-chardev-backends
- Fix image creation option defaults that exist in both the format and
the protocol layer (e.g. 'cluster_size' in qcow2 and rbd; the qcow2
default was incorrectly applied to the rbd layer)
-----BEGIN PGP SIGNATURE-----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=zZCm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches and object-add QAPIfication
- QAPIfy object-add and --object
- stream: Fail gracefully if permission is denied
- storage-daemon: Fix crash on quit when job is still running
- curl: Fix use after free
- char: Deprecate backend aliases, fix QMP query-chardev-backends
- Fix image creation option defaults that exist in both the format and
the protocol layer (e.g. 'cluster_size' in qcow2 and rbd; the qcow2
default was incorrectly applied to the rbd layer)
# gpg: Signature made Fri 19 Mar 2021 09:18:22 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (42 commits)
vl: allow passing JSON to -object
qom: move user_creatable_add_opts logic to vl.c and QAPIfy it
tests: convert check-qom-proplist to keyval
qom: Support JSON in HMP object_add and tools --object
char: Simplify chardev_name_foreach()
char: Deprecate backend aliases 'tty' and 'parport'
char: Skip CLI aliases in query-chardev-backends
qom: Add user_creatable_parse_str()
hmp: QAPIfy object_add
qemu-img: Use user_creatable_process_cmdline() for --object
qom: Add user_creatable_add_from_str()
qemu-nbd: Use user_creatable_process_cmdline() for --object
qemu-io: Use user_creatable_process_cmdline() for --object
qom: Factor out user_creatable_process_cmdline()
qom: Remove user_creatable_add_dict()
qemu-storage-daemon: Implement --object with qmp_object_add()
qom: Make "object" QemuOptsList optional
qapi/qom: QAPIfy object-add
qapi/qom: Add ObjectOptions for x-remote-object
qapi/qom: Add ObjectOptions for input-*
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This converts object-add from 'gen': false to the ObjectOptions QAPI
type. As an immediate benefit, clients can now use QAPI schema
introspection for user creatable QOM objects.
It is also the first step towards making the QAPI schema the only
external interface for the creation of user creatable objects. Once all
other places (HMP and command lines of the system emulator and all
tools) go through QAPI, too, some object implementations can be
simplified because some checks (e.g. that mandatory options are set) are
already performed by QAPI, and in another step, QOM boilerplate code
could be generated from the schema.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
* fixes for Coverity CID 1450756, 1450757 and 1450758 (me)
* fix for a bug in zone management receive (me)
* metadata and end-to-end data protection support (me & Gollu Appalanaidu)
* verify support (Gollu Appalanaidu)
* multiple lba formats and format nvm support (Minwoo Im)
and a couple of misc refactorings from me.
v2:
- remove an unintended submodule update. Argh.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmBTP0wACgkQTeGvMW1P
DelZvAf+Ijw77YLz2t0P97CiwoOAG4FADwo61WQJo2AHyS3JMYPVdgNUXF7UGt/S
cNhU1JjdEylgZPKi5t9o/qgy7+vtSL0KKqoXIS0z9ZWZkdFsgObNetGULhaqXgaX
4KcAt7PyJS/33uFqYGSVZxJTO4GtCy34hGw6XrVs388tQD1S+eI+oS5EYBN57rl9
MrV5Z72iMCBx8Y074u81SD/u7n34b5WWbUOJADVI1rAKhilDhnkAhBQ/gK/UBodB
trUUQY/KU+eCnXEqfBeMD6fL75UOAFOjnm7Kfk/Q/g3di3H2fu0RGLrJuSS1dG0n
zmwgE7pQ1jT1UcB3QwAJLR3tGtd6sA==
=HwqP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/nvme/tags/nvme-next-pull-request' into staging
emulated nvme updates and fixes
* fixes for Coverity CID 1450756, 1450757 and 1450758 (me)
* fix for a bug in zone management receive (me)
* metadata and end-to-end data protection support (me & Gollu Appalanaidu)
* verify support (Gollu Appalanaidu)
* multiple lba formats and format nvm support (Minwoo Im)
and a couple of misc refactorings from me.
v2:
- remove an unintended submodule update. Argh.
# gpg: Signature made Thu 18 Mar 2021 11:53:48 GMT
# gpg: using RSA key 522833AA75E2DCE6A24766C04DE1AF316D4F0DE9
# gpg: Good signature from "Klaus Jensen <its@irrelevant.dk>" [unknown]
# gpg: aka "Klaus Jensen <k.jensen@samsung.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DDCA 4D9C 9EF9 31CC 3468 4272 63D5 6FC5 E55D A838
# Subkey fingerprint: 5228 33AA 75E2 DCE6 A247 66C0 4DE1 AF31 6D4F 0DE9
* remotes/nvme/tags/nvme-next-pull-request:
hw/block/nvme: add support for the format nvm command
hw/block/nvme: pull lba format initialization
hw/block/nvme: prefer runtime helpers instead of device parameters
hw/block/nvme: support multiple lba formats
hw/block/nvme: add non-mdts command size limit for verify
hw/block/nvme: add verify command
hw/block/nvme: end-to-end data protection
hw/block/nvme: add metadata support
hw/block/nvme: fix zone management receive reporting too many zones
hw/block/nvme: assert namespaces array indices
hw/block/nvme: fix potential overflow
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Format NVM admin command can make a namespace or namespaces to be
with different LBA size and metadata size with protection information
types.
This patch introduces Format NVM command with LBA format, Metadata, and
Protection Information for the device. The secure erase operation things
and support for formatting zoned namespaces are yet to be added.
The parameter checks inside of this patch has been referred from
Keith's old branch.
Signed-off-by: Minwoo Im <minwoo.im@samsung.com>
[anaidu.gollu: rebased on e2e]
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: rebased for reworked aio tracking]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Pull lba format initialization code into separate function in
preparation for Format NVM support.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
In preparation for Format NVM support, use runtime helpers instead of
the constant device parameters when getting lba size information etc.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
This patch introduces multiple LBA formats supported with the typical
logical block sizes of 512 bytes and 4096 bytes as well as metadata
sizes of 0, 8, 16 and 64 bytes. The format will be chosed based on the
lbads and ms parameters of the nvme-ns device.
Signed-off-by: Minwoo Im <minwoo.im@samsung.com>
[k.jensen: resurrected and rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Verify is not subject to MDTS, so a single Verify command may result in
excessive amounts of allocated memory. Impose a limit on the data size
by adding support for TP 4040 ("Non-MDTS Command Size Limits").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for namespaces formatted with protection information. The
type of end-to-end data protection (i.e. Type 1, Type 2 or Type 3) is
selected with the `pi` nvme-ns device parameter. If the number of
metadata bytes is larger than 8, the `pil` nvme-ns device parameter may
be used to control the location of the 8-byte DIF tuple. The default
`pil` value of '0', causes the DIF tuple to be transferred as the last
8 bytes of the metadata. Set to 1 to store this in the first eight bytes
instead.
Co-authored-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for metadata in the form of extended logical blocks as well
as a separate buffer of data. The new `ms` nvme-ns device parameter
specifies the size of metadata per logical block in bytes. The `mset`
nvme-ns device parameter controls whether metadata is transfered as part
of an extended lba (set to '1') or in a separate buffer (set to '0',
the default).
Regardsless of the scheme chosen with `mset`, metadata is stored at the
end of the namespace backing block device. This requires the user
provided PRP/SGLs to be walked and "split" into data and metadata
scatter/gather lists if the extended logical block scheme is used, but
has the advantage of not breaking the deallocated blocks support.
Co-authored-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
nvme_zone_mgmt_recv uses nvme_ns_nlbas() to get the number of LBAs in
the namespace and then calculates the number of zones to report by
incrementing slba with ZSZE until exceeding the number of LBAs as
returned by nvme_ns_nlbas().
This is bad because the namespace might be of such as size that some
LBAs are valid, but are not part of any zone, causing zone management
receive to report one additional (but non-existing) zone.
Fix this with a conventional loop on i < ns->num_zones instead.
Fixes: a479335bfa ("hw/block/nvme: Support Zoned Namespace Command Set")
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Coverity complains about a possible memory corruption in the
nvme_ns_attach and _detach functions. While we should not (famous last
words) be able to reach this function without nsid having previously
been validated, this is still an open door for future misuse.
Make Coverity and maintainers happy by asserting that the index into the
array is valid. Also, while not detected by Coverity (yet), add an
assert in nvme_subsys_ns and nvme_subsys_register_ns as well since a
similar issue is exists there.
Fixes: 037953b5b2 ("hw/block/nvme: support namespace detach")
Fixes: CID 1450757
Fixes: CID 1450758
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
page_size is a uint32_t, and zasl is a uint8_t, so the expression
`page_size << zasl` is done using 32-bit arithmetic and might overflow.
Since we then compare this against a 64 bit data_size value, Coverity
complains that we might overflow unintentionally. An MDTS/ZASL value in
excess of 4GiB is probably impractical, but it is not entirely
unrealistic, so add a cast such that we handle that case properly.
Fixes: 578d914b26 ("hw/block/nvme: align zoned.zasl with mdts")
Fixes: CID 1450756
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Rather than having a device specific debug implementation in
pflash_cfi01.c and pflash_cfi02.c, use the standard tracing facility.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210216142721.1985543-2-david.edmondson@oracle.com>
[PMD: Rebased, fixed pflash_write_block_erase trace event format]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
PFlashCFI01.ro is a bool, declare it as such.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210216142721.1985543-3-david.edmondson@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the 'mode_read_array' event when we set the device in such
mode, and use the 'reset' event in DeviceReset handler.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210310170528.1184868-10-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210310170528.1184868-9-philmd@redhat.com>
There is multiple places resetting the internal state machine.
Factor the code out in a new pflash_reset_state_machine() method.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210310170528.1184868-8-philmd@redhat.com>
The same pattern is used when setting the flash in READ_ARRAY mode:
- Set the state machine command to READ_ARRAY
- Reset the write_cycle counter
- Reset the memory region in ROMD
Refactor the current code by extracting this pattern.
It is used three times:
- When the timer expires and not in bypass mode
- On a read access (on invalid command).
- When the device is initialized. Here the ROMD mode is hidden
by the memory_region_init_rom_device() call.
pflash_register_memory(rom_mode=true) already sets the ROM device
in "read array" mode (from I/O device to ROM one). Explicit that
by renaming the function as pflash_mode_read_array(), adding
a trace event and resetting wcycle.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210310170528.1184868-7-philmd@redhat.com>
There is only one call to pflash_register_memory() with
rom_mode == false. As we want to modify pflash_register_memory()
in the next patch, open-code this trivial function in place for
the 'rom_mode == false' case.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20210310170528.1184868-6-philmd@redhat.com>
There is only one call to pflash_setup_mappings(). Convert 'rom_mode'
to boolean and set it to true directly within pflash_setup_mappings().
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20210310170528.1184868-5-philmd@redhat.com>
Fill the CFI table in out of DeviceRealize() in a new function:
pflash_cfi02_fill_cfi_table().
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210310170528.1184868-4-philmd@redhat.com>
Fill the CFI table in out of DeviceRealize() in a new function:
pflash_cfi01_fill_cfi_table().
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210310170528.1184868-3-philmd@redhat.com>
We are going to move this code, fix its style first.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210310170528.1184868-2-philmd@redhat.com>
The 'scsi-hd' and 'scsi-cd' devices provide suitable alternatives.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The 'ide-hd' and 'ide-cd' devices provide suitable alternatives.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The newer 'query-cpus-fast' command avoids side effects on the guest
execution. Note that some of the field names are different in the
'query-cpus-fast' command.
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Tested-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
- get rid of legacy_s390_alloc() and phys_mem_set_alloc()
- tcg: implement the MVPG condition-code-option bit
- fix g_autofree variable handing in the pci vfio code
- use official z15 names in the cpu model definitions
-----BEGIN PGP SIGNATURE-----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=8eNE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck-gitlab/tags/s390x-20210316' into staging
s390x updates:
- get rid of legacy_s390_alloc() and phys_mem_set_alloc()
- tcg: implement the MVPG condition-code-option bit
- fix g_autofree variable handing in the pci vfio code
- use official z15 names in the cpu model definitions
# gpg: Signature made Tue 16 Mar 2021 10:04:21 GMT
# gpg: using RSA key C3D0D66DC3624FF6A8C018CEDECF6B93C6F02FAF
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck-gitlab/tags/s390x-20210316:
s390x/pci: Add missing initialization for g_autofree variables
target/s390x: Store r1/r2 for page-translation exceptions during MVPG
target/s390x: Implement the MVPG condition-code-option bit
s390x/cpu_model: use official name for 8562
exec: Get rid of phys_mem_set_alloc()
s390x/kvm: Get rid of legacy_s390_alloc()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a Kconfig entry for guest-loader so we can optionally deselect
it (default is built in), and add a Meson dependency on libfdt.
This fixes when building with --disable-fdt:
/usr/bin/ld: libcommon.fa.p/hw_core_guest-loader.c.o: in function `loader_insert_platform_data':
hw/core/guest-loader.c:56: undefined reference to `qemu_fdt_add_subnode'
/usr/bin/ld: hw/core/guest-loader.c:57: undefined reference to `qemu_fdt_setprop'
/usr/bin/ld: hw/core/guest-loader.c:61: undefined reference to `qemu_fdt_setprop_string_array'
/usr/bin/ld: hw/core/guest-loader.c:68: undefined reference to `qemu_fdt_setprop_string'
/usr/bin/ld: hw/core/guest-loader.c:74: undefined reference to `qemu_fdt_setprop_string_array'
collect2: error: ld returned 1 exit status
Fixes: a33ff6d2c6 ("hw/core: implement a guest-loader to support static hypervisor guests")
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210315170439.2868903-1-philmd@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The original implementation of the Macintosh VIA devices in commit 6dca62a000
"hw/m68k: add VIA support" used timer optimisations to reduce high CPU usage on
the host when booting Linux. These optimisations worked by waiting until VIA1
port B was accessed before re-arming the timers.
The MacOS toolbox ROM constantly writes to VIA1 port B which calls
via1_one_second_update() and via1_sixty_hz_update() to calculate the new expiry
time, causing the timers to constantly reset and never fire. The effect of this
is that the Ticks (0x16a) global variable holding the number of 60Hz timer ticks
since reset is never incremented by the interrupt causing time to stand still.
Whilst the code was introduced as a performance optimisation, it is likely that
the high CPU usage was actually caused by the incorrect 60Hz timer interval
fixed in the previous patch. Remove the optimisation to keep everything simple
and enable the MacOS toolbox ROM to start keeping time.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The 60Hz timer is initialised using timer_new_ns() meaning that the timer
interval should be measured in ns, and therefore its period is a thousand
times too short.
Use a define for the 60Hz timer period taking the more precise value as
documented in the Guide To The Macintosh Family Hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210311100505.22596-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to the "Guide To The Macintosh Family Hardware", the 60Hz VIA1 timer
on newer Macs such as the Quadra only exists for compatibility with old software
and is no longer synced to the VBL interval.
Rename the VBL timer to 60Hz timer to emphasise this and to prevent confusion
when the real VBL interrupt (now handled as a NuBus slot interrupt) is added in
future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210311100505.22596-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The current workaround for the Linux ADB state machine in kernels < 5.6 switching
the VIA back to IDLE state between send and receive modes is to re-inject the
first byte of the response in the IDLE state, and then force the state machine
into generating an autopoll reply.
In fact what is happening is much simpler: analysis of traces from a real Quadra
suggest that the existing data is returned as the first autopoll response rather
than generating an immediate response starting whilst still in IDLE state.
Update the ADB receive code to work in the same way, which allows the re-injection
code to be completely removed from adb_via_receive() and for adb_via_poll() to
be simplified accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210311100505.22596-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS SCSI driver uses a long access to read the VIA registers rather than
just a single byte during the message out phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The use of the post-increment operator on adb_data_in_index meant that the
trace-event was accidentally displaying the next byte in the incoming ADB
data buffer rather than the current byte.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since all the documentation uses the hex offsets, this makes it much easier
to see what is going on.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210311100505.22596-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
QEMU timer of channel 0 in i8254 is used to raise irq
at the specified moment of time. This irq can be disabled
with irq_disabled flag. But when vmstate of the pit is
loaded, timer may be rearmed despite the disabled interrupts.
This patch adds irq_disabled flag check to fix that.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Message-Id: <161537170060.6654.9430112746749476215.stgit@pasha-ThinkPad-X280>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For testing, it can be useful to simulate an enormous amount of memory
(e.g. 2^64 RAM). This adds an MMIO device that acts as sparse memory.
When something writes a nonzero value to a sparse-mem address, we
allocate a block of memory. For now, since the only user of this device
is the fuzzer, we do not track and free zeroed blocks. The device has a
very low priority (so it can be mapped beneath actual RAM, and virtual
device MMIO regions).
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For now the switch of vfio dirty page tracking is integrated into
@vfio_save_handler. The reason is that some PCI vendor driver may
start to track dirty base on _SAVING state of device, so if dirty
tracking is started before setting device state, vfio will report
full-dirty to QEMU.
However, the dirty bmap of all ramblocks are fully set when setup
ram saving, so it's not matter whether the device is in _SAVING
state when start vfio dirty tracking.
Moreover, this logic causes some problems [1]. The object of dirty
tracking is guest memory, but the object of @vfio_save_handler is
device state, which produces unnecessary coupling and conflicts:
1. Coupling: Their saving granule is different (perVM vs perDevice).
vfio will enable dirty_page_tracking for each devices, actually
once is enough.
2. Conflicts: The ram_save_setup() traverses all memory_listeners
to execute their log_start() and log_sync() hooks to get the
first round dirty bitmap, which is used by the bulk stage of
ram saving. However, as vfio dirty tracking is not yet started,
it can't get dirty bitmap from vfio. Then we give up the chance
to handle vfio dirty page at bulk stage.
Move the switch of vfio dirty_page_tracking into vfio_memory_listener
can solve above problems. Besides, Do not require devices in SAVING
state for vfio_sync_dirty_bitmap().
[1] https://www.spinics.net/lists/kvm/msg229967.html
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210309031913.11508-1-zhukeqian1@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The cpu_physical_memory_set_dirty_lebitmap() can quickly deal with
the dirty pages of memory by bitmap-traveling, regardless of whether
the bitmap is aligned correctly or not.
cpu_physical_memory_set_dirty_lebitmap() supports pages in bitmap of
host page size. So it'd better to set bitmap_pgsize to host page size
to support more translation granule sizes.
[aw: The Fixes commit below introduced code to restrict migration
support to configurations where the target page size intersects the
host dirty page support. For example, a 4K guest on a 4K host.
Due to the above flexibility in bitmap handling, this restriction
unnecessarily prevents mixed target/host pages size that could
otherwise be supported. Use host page size for dirty bitmap.]
Fixes: 87ea529c50 ("vfio: Get migration capability flags for container")
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Message-Id: <20210304133446.1521-1-jiangkunkun@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In VFIO migration resume phase and some guest startups, there are
already unmasked vectors in the vector table when calling
vfio_msix_enable(). So in order to avoid inefficiently disabling
and enabling vectors repeatedly, let's allocate all needed vectors
first and then enable these unmasked vectors one by one without
disabling.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Message-Id: <20210310030233.1133-4-lushenming@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In the VFIO VM state change handler when stopping the VM, the _RUNNING
bit in device_state is cleared which makes the VFIO device stop, including
no longer generating interrupts. Then we can save the pending states of
all interrupts in the GIC VM state change handler (on ARM).
So we have to set the priority of the VFIO VM state change handler
explicitly (like virtio devices) to ensure it is called before the
GIC's in saving.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20210310030233.1133-3-lushenming@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
On ARM64 the VFIO SET_IRQS ioctl is dependent on the VM interrupt
setup, if the restoring of the VFIO PCI device config space is
before the VGIC, an error might occur in the kernel.
So we move the saving of the config space to the non-iterable
process, thus it will be called after the VGIC according to
their priorities.
As for the possible dependence of the device specific migration
data on it's config space, we can let the vendor driver to
include any config info it needs in its own data stream.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Message-Id: <20210310030233.1133-2-lushenming@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Previous work on dev-iotlb message broke spapr_iommu/vhost integration
as it did for SMMU and virtio-iommu. The spapr_iommu currently
only sends IOMMU_NOTIFIER_UNMAP notifications. Since commit
958ec334bc ("vhost: Unbreak SMMU and virtio-iommu on dev-iotlb support"),
VHOST first tries to register IOMMU_NOTIFIER_DEVIOTLB_UNMAP notifier
and if it fails, falls back to legacy IOMMU_NOTIFIER_UNMAP. So
spapr_iommu must fail on the IOMMU_NOTIFIER_DEVIOTLB_UNMAP
registration.
Reported-by: Peter Xu <peterx@redhat.com>
Fixes: b68ba1ca57 ("memory: Add IOMMU_NOTIFIER_DEVIOTLB_UNMAP IOMMUTLBNotificationType")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210209213233.40985-3-eric.auger@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In an attempt to fix smmu/virtio-iommu - vhost regression, commit
958ec334bc ("vhost: Unbreak SMMU and virtio-iommu on dev-iotlb support")
broke virtio-iommu integration. This is due to the fact VFIO registers
IOMMU_NOTIFIER_ALL notifiers, which includes IOMMU_NOTIFIER_DEVIOTLB_UNMAP
and this latter now is rejected by the virtio-iommu. As a consequence,
the registration fails. VHOST behaves like a device with an ATC cache. The
VFIO device does not support this scheme yet.
Let's register only legacy MAP and UNMAP notifiers.
Fixes: 958ec334bc ("vhost: Unbreak SMMU and virtio-iommu on dev-iotlb support")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210209213233.40985-2-eric.auger@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Follow the inclusive terminology from the "Conscious Language in your
Open Source Projects" guidelines [*] and replace the word "blacklist"
appropriately.
[*] https://github.com/conscious-lang/conscious-lang-docs/blob/main/faq.md
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210205171817.2108907-9-philmd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is an obvious typo in the function name of the .log_sync() callback.
Spell it correctly.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-Id: <20201204014240.772-1-yuzenghui@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJgTx3xAAoJEO8Ells5jWIRtBsH/2MCZJKg4wTB4a7qAYTyuUmZ
qz1Z8d5J1JSyAQiiUN+lFo1Gtpuqpyci4CT5gHz4ru2UV9DBJy9cDGApug66QOM8
stbztOeRIfcLLeWCepQIoSESteesiyMM6h1Q/x9lF87eN7JXrNmACp+jAhTDHq1B
QFwYVGLwkaFkvE9G04yzCZSo37+j2nPAauIuoJs1B01on6a5hj7Isdumn2P1TGyz
6nJTkyWLsPzEM+lGMfxYdMpnELibJ935CX78DGcnZK9qhI7rw4xLFuZtyTW+N+B8
h5OX9aCqrIF5AX7xNTvQeQwclnEe+KzBUwkbDJARViEUDOoKfb6t1Yv+3Xghdqo=
=57xH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 15 Mar 2021 08:42:25 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: Do not fill legacy info_str for backends
hmp: Use QAPI NetdevInfo in hmp_info_network
net: Move NetClientState.info_str to dynamic allocations
tests: Add tests for query-netdev command
qapi: net: Add query-netdev command
pvrdma: wean code off pvrdma_ring.h kernel header
lan9118: switch to use qemu_receive_packet() for loopback
cadence_gem: switch to use qemu_receive_packet() for loopback
pcnet: switch to use qemu_receive_packet() for loopback
rtl8139: switch to use qemu_receive_packet() for loopback
tx_pkt: switch to use qemu_receive_packet_iov() for loopback
sungem: switch to use qemu_receive_packet() for loopback
msf2-mac: switch to use qemu_receive_packet() for loopback
dp8393x: switch to use qemu_receive_packet() for loopback packet
e1000: switch to use qemu_receive_packet() for loopback
net: introduce qemu_receive_packet()
e1000: fail early for evil descriptor
net: validate that ids are well formed
net: Fix build error when DEBUG_NET is on
virtio-net: calculating proper msix vectors on init
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/core/machine.c
Replaced a call to qemu_mutex_lock and its respective call to
qemu_mutex_unlock and used QEMU_LOCK_GUARD macro in their place.
This simplifies the code by removing the call required to unlock
and also eliminates goto paths.
Signed-off-by: Mahmoud Mandour <ma.mandourr@gmail.com>
Acked-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <20210311031538.5325-9-ma.mandourr@gmail.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
The machine is based on Goldfish interfaces defined by Google
for Android simulator. It uses Goldfish-rtc (timer and RTC),
Goldfish-pic (PIC) and Goldfish-tty (for serial port and early tty).
The machine is created with 128 virtio-mmio bus, and they can
be used to use serial console, GPU, disk, NIC, HID, ...
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-6-laurent@vivier.eu>
Add a system controller for the m68k-virt machine.
This controller allows the kernel to power off or reset the machine.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-5-laurent@vivier.eu>
A (generic) copy of the GLUE device we already have for q800 to use with
the m68k-virt machine.
The q800 one would disappear in the future as q800 uses actually the djMEMC
controller.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-4-laurent@vivier.eu>
Implement the goldfish pic device as defined in
https://android.googlesource.com/platform/external/qemu/+/master/docs/GOLDFISH-VIRTUAL-HARDWARE.TXT
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-3-laurent@vivier.eu>
Stale data in csw (specifically residue) can confuse the state machine
and allows the guest trigger an assert(). So clear csw on reset to
avoid this happening in case the guest resets the device in the middle
of a request.
Buglink: https://bugs.launchpad.net/qemu/+bug/1523811
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210312094954.796799-1-kraxel@redhat.com>
Add new kconfig symbols so usb-storage and usb-bot can
be enabled or disabled individually at build time.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210312090425.772900-5-kraxel@redhat.com>
In preparation for splitting the usb-storage.c file move
declarations to the new usb/msd.h header file.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210312090425.772900-2-kraxel@redhat.com>
Extract the VT82C686 PCI UHCI function into a new unit so
it is only build when the VT82C686 south bridge is selected.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210309190802.830969-4-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Extract generic UHCI prototypes into a new "hcd-uhci.h" local
header so we can reuse them in other units.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210309190802.830969-3-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The VT82C686 south bridge provides a USB UHCI bus via a PCI function.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210309190802.830969-2-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When trying to remove the -usbdevice option, there were complaints that
"-usbdevice braille" is still a very useful shortcut for some people.
Thus we never remove this option. Since it's not such a big burden to
keep it around, and it's also convenient in the sense that you don't
have to worry to enable a host controller explicitly with this option,
we should remove it from he deprecation list again.
However, there is one exception: "-usbdevice audio" should go away, since
audio devices without "audiodev=..." parameter are also on the deprecation
list and you cannot use "-usbdevice audio" with "audiodev".
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210310173323.1422754-4-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
No device needs them anymore and in fact they're undocumented.
Remove the code. The only change in behavior is that "-usbdevice
braille:hello" now reports an error, which is a bugfix.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210310173323.1422754-2-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This property was only required for the pc-1.0 and earlier machine
types. Since these have been removed now, we can delete the property
as well.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210302120152.118042-1-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When declaring g_autofree variable without initialization, compiler
will raise "may be used uninitialized in this function" warning due
to automatic free handling.
This is mentioned in docs/devel/style.rst (quote from section
"Automatic memory deallocation"):
* Variables declared with g_auto* MUST always be initialized,
otherwise the cleanup function will use uninitialized stack memory
Add initialization for these declarations to prevent the warning and
comply with coding style.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Fixes: cd7498d07f ("s390x/pci: Add routine to get the vfio dma available count")
Fixes: 1e7552ff5c ("s390x/pci: get zPCI function info from host")
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20210315101352.152888-1-mrezanin@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Report the configured granularity for discard operation to the
guest. If this is not set use the block size.
Since until now we have ignored the configured discard granularity
and always reported the block size, let's add
'report-discard-granularity' property and disable it for older
machine types to avoid migration issues.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210225001239.47046-1-akihiko.odaki@gmail.com>
The info_str field of the NetClientState structure is static and has a size
of 256 bytes. This amount is often unclaimed, and the field itself is used
exclusively for HMP "info network".
The patch translates info_str to dynamic memory allocation.
This action is also allows us to painlessly discard usage of this field
for backend devices.
Signed-off-by: Alexey Kirillov <lekiravi@yandex-team.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The pvrdma code relies on the pvrdma_ring.h kernel header for some
basic ring buffer handling. The content of that header isn't very
exciting, but contains some (q)atomic_*() invocations that (a)
cause manual massaging when doing a headers update, and (b) are
an indication that we probably should not be importing that header
at all.
Let's reimplement the ring buffer handling directly in the pvrdma
code instead. This arguably also improves readability of the code.
Importing the header can now be dropped.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Tested-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Buglink: https://bugs.launchpad.net/qemu/+bug/1917085
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Buglink: https://bugs.launchpad.net/qemu/+bug/1910826
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_receive_iov() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
During procss_tx_desc(), driver can try to chain data descriptor with
legacy descriptor, when will lead underflow for the following
calculation in process_tx_desc() for bytes:
if (tp->size + bytes > msh)
bytes = msh - tp->size;
This will lead a infinite loop. So check and fail early if tp->size if
greater or equal to msh.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cheolwoo Myung <cwmyung@snu.ac.kr>
Reported-by: Ruhr-University Bochum <bugs-syssec@rub.de>
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Currently, the default msix vectors for virtio-net-pci is 3 which is
obvious not suitable for multiqueue guest, so we depends on the user
or management tools to pass a correct vectors parameter. In fact, we
can simplifying this by calculating the number of vectors on realize.
Consider we have N queues, the number of vectors needed is 2*N + 2
(#queue pairs + plus one config interrupt and control vq). We didn't
check whether or not host support control vq because it was added
unconditionally by qemu to avoid breaking legacy guests such as Minix.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael Rolnik <mrolnik@gmail.com>
Message-Id: <20210313165445.2113938-3-f4bug@amsat.org>
Add the yellow "lime" LED.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael Rolnik <mrolnik@gmail.com>
Message-Id: <20210313165445.2113938-2-f4bug@amsat.org>
The template header is now included only once; just inline its contents
in hw/display/pxa2xx_lcd.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-10-peter.maydell@linaro.org
We're about to move code from the template header into pxa2xx_lcd.c.
Before doing that, make coding style fixes so checkpatch doesn't
complain about the patch which moves the code. This commit is
whitespace changes only:
* avoid hard-coded tabs
* fix ident on function prototypes
* no newline before open brace on array definitions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-9-peter.maydell@linaro.org
We're about to move code from the template header into pxa2xx_lcd.c.
Before doing that, make coding style fixes so checkpatch doesn't
complain about the patch which moves the code. This commit fixes
missing braces in the SKIP_PIXEL() macro definition and in if()
statements.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-8-peter.maydell@linaro.org
Now that BITS is always 32, expand out all its uses in the template
header, including removing now-useless uses of the glue() macro.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-7-peter.maydell@linaro.org
Since the dest_width is now always 4 because the output surface is
32bpp, we can replace the dest_width state field with a constant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-6-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel. Remove the legacy dead code
from the pxa2xx_lcd display device which was handling the possibility
that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-5-peter.maydell@linaro.org
BITS is always 32, so remove all uses of it from the template header,
by dropping the trailing '32' from the draw function names and
not constructing the name of rgb_to_pixel32() via the glue() macro.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-4-peter.maydell@linaro.org
The pl110_template.h header has a doubly-nested multiple-include pattern:
* pl110.c includes it once for each host bit depth (now always 32)
* every time it is included, it includes itself 6 times, to account
for multiple guest device pixel and byte orders
Now we only have to deal with 32-bit host bit depths, we can move the
code corresponding to the outer layer of this double-nesting to be
directly in pl110.c and reduce the template header to a single layer
of nesting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-3-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel. Remove the legacy dead
code from the pl110 display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210211141515.8755-2-peter.maydell@linaro.org
Trace all accesses to Internal Space Decode (ISD) registers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210309142630.728014-6-f4bug@amsat.org>
We want to trace all register accesses. First rename the current
gt64120_read / gt64120_write events with '_intreg' suffix, as they
are restricted to interrupt registers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210309142630.728014-5-f4bug@amsat.org>
Fix the following typos:
- GT_PCI1_CFGDATA is not a timer register but a PCI one,
- zero-padding flag is out of the format
Fixes: 641ca2bfcd ("hw/mips/gt64xxx_pci: Use qemu_log_mask() instead of debug printf()")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210309142630.728014-4-f4bug@amsat.org>
The ISD MemoryRegion is implemented for 32-bit accesses.
Simplify it by setting the MemoryRegionOps::impl min/max
access size fields.
Since the region is registered with a size of 0x1000 bytes,
we can remove the hwaddr mask.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210309142630.728014-3-f4bug@amsat.org>
The ISD I/O region belongs to the TYPE_GT64120_PCI_HOST_BRIDGE,
so initialize it before it is realized, not after.
Rename the region as 'gt64120-isd' so it is clearer to realize
it belongs to the GT64120 in the memory tree view.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210309142630.728014-2-f4bug@amsat.org>
This patch adds fan_splitters (split IRQs) in NPCM7XX boards. Each fan
splitter corresponds to 1 PWM output and can connect to multiple fan
inputs (MFT devices).
In NPCM7XX boards(NPCM750 EVB and Quanta GSJ boards), we initializes
these splitters and connect them to their corresponding modules
according their specific device trees.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements Multi Function Timer (MFT) module for NPCM7XX.
This module is mainly used to configure PWM fans. It has just enough
functionality to make the PWM fan kernel module work.
The module takes two input, the max_rpm of a fan (modifiable via QMP)
and duty cycle (a GPIO from the PWM module.) The actual measured RPM
is equal to max_rpm * duty_cycle / NPCM7XX_PWM_MAX_DUTY. The RPM is
measured as a counter compared to a prescaled input clock. The kernel
driver reads this counter and report to user space.
Refs:
https://github.com/torvalds/linux/blob/master/drivers/hwmon/npcm750-pwm-fan.c
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210311180855.149764-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds GPIOs in NPCM7xx PWM module for its duty values.
The purpose of this is to connect it to the MFT module to provide
an input for measuring a PWM fan's RPM. Each PWM module has
NPCM7XX_PWM_PER_MODULE of GPIOs, each one corresponds to
one PWM instance and can connect to multiple fan instances in MFT.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-2-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine already checks KVM_CAP_ARM_VM_IPA_SIZE to get the
upper bound of the IPA size. If that bound is lower than the highest
possible GPA for the machine, then QEMU will error out. However, the
IPA is set to 40 when the highest GPA is less than or equal to 40,
even when KVM may support an IPA limit as low as 32. This means KVM
may fail the VM creation unnecessarily. Additionally, 40 is selected
with the value 0, which means use the default, and that gets around
a check in some versions of KVM, causing a difficult to debug fail.
Always use the IPA size that corresponds to the highest possible GPA,
unless it's lower than 32, in which case use 32. Also, we must still
use 0 when KVM only supports the legacy fixed 40 bit IPA.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Message-id: 20210310135218.255205-3-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the SSECounter link is absent, we set an error message
in sse_timer_realize() but forgot to propagate this error.
Add the missing 'return'.
Fixes: CID 1450755 (Null pointer dereferences)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210312001845.1562670-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the emulated EMAC for sun8i always traverses the transmit queue
from the head when transferring packets. It searches for a list of consecutive
descriptors whichs are flagged as ready for processing and transmits their payloads
accordingly. The controller stops processing once it finds a descriptor that is not
marked ready.
While the above behaviour works in most situations, it is not the same as the actual
EMAC in hardware. Actual hardware uses the TX_CUR_DESC register value to keep track
of the last position in the transmit queue and continues processing from that position
when software triggers the start of DMA processing. The currently emulated behaviour can
lead to packet loss on transmit when software fills the transmit queue with ready
descriptors that overlap the tail of the circular list.
This commit modifies the emulated EMAC for sun8i such that it processes
the transmit queue using the TX_CUR_DESC register in the same way as hardware.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210310195820.21950-2-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert all sid printouts to sid=0x%x.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210309102742.30442-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the whole SID range (32b) is invalidated (SMMU_CMD_CFGI_ALL),
@end overflows and we fail to handle the command properly.
Once this gets fixed, the current code really is awkward in the
sense it loops over the whole range instead of removing the
currently cached configs through a hash table lookup.
Fix both the overflow and the lookup.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210309102742.30442-7-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of today, the driver can invalidate a number of pages that is
not a power of 2. However IOTLB unmap notifications and internal
IOTLB invalidations work with masks leading to erroneous
invalidations.
In case the range is not a power of 2, split invalidations into
power of 2 invalidations.
When looking for a single page entry in the vSMMU internal IOTLB,
let's make sure that if the entry is not found using a
g_hash_table_remove() we iterate over all the entries to find a
potential range that overlaps it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the asid is not set, do not attempt to locate the key directly
as all inserted keys have a valid asid.
Use g_hash_table_foreach_remove instead.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-5-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Unmap notifiers work with an address mask assuming an
invalidation range of a power of 2. Nothing mandates this
in the VIRTIO-IOMMU spec.
So in case the range is not a power of 2, split it into
several invalidations.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20210309102742.30442-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently get_naturally_aligned_size() is used by the intel iommu
to compute the maximum invalidation range based on @size which is
a power of 2 while being aligned with the @start address and less
than the maximum range defined by @gaw.
This helper is also useful for other iommu devices (virtio-iommu,
SMMUv3) to make sure IOMMU UNMAP notifiers only are called with
power of 2 range sizes.
Let's move this latter into dma-helpers.c and rename it into
dma_aligned_pow2_mask(). Also rewrite the helper so that it
accomodates UINT64_MAX values for the size mask and max mask.
It now returns a mask instead of a size. Change the caller.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20210309102742.30442-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With -Werror=maybe-uninitialized configuration we get
../hw/i386/intel_iommu.c: In function ‘vtd_context_device_invalidate’:
../hw/i386/intel_iommu.c:1888:10: error: ‘mask’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
1888 | mask = ~mask;
| ~~~~~^~~~~~~
Add a g_assert_not_reached() to avoid the error.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210309102742.30442-2-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for the Versal Accelerator RAMs (XRAMs).
Reviewed-by: Luc Michel <luc@lmichel.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the Xilinx Versal Accelerator RAM (XRAM).
This is mainly a stub to make firmware happy. The size of
the RAMs can be probed. The interrupt mask logic is
modelled but none of the interrups will ever be raised
unless injected.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-2-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=/uyx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210310' into staging
ppc patch queue for 2021-03-10
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
# gpg: Signature made Wed 10 Mar 2021 04:08:53 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210310:
spapr.c: send QAPI event when memory hotunplug fails
spapr.c: remove duplicated assert in spapr_memory_unplug_request()
target/ppc: fix icount support on Book-e vms accessing SPRs
qemu_timer.c: add timer_deadline_ms() helper
spapr_pci.c: add 'unplug already in progress' message for PCI unplug
spapr.c: add 'unplug already in progress' message for PHB unplug
hw/ppc: e500: Add missing <ranges> in the eTSEC node
hw/net: fsl_etsec: Fix build error when HEX_DUMP is on
spapr_drc.c: use DRC reconfiguration to cleanup DIMM unplug state
spapr_drc.c: add hotunplug timeout for CPUs
spapr_drc.c: introduce unplug_timeout_timer
target/ppc: Fix bcdsub. emulation when result overflows
docs/system: Extend PPC section
spapr: rename spapr_drc_detach() to spapr_drc_unplug_request()
spapr_drc.c: use spapr_drc_release() in isolate_physical/set_unusable
pseries: Update SLOF firmware image
spapr_drc.c: do not call spapr_drc_detach() in drc_isolate_logical()
hw/display/sm501: Inline template header into C file
hw/display/sm501: Expand out macros in template header
hw/display/sm501: Remove dead code for non-32-bit RGB surfaces
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New model for the Aspeed LPC controller
* Misc cleanups
-----BEGIN PGP SIGNATURE-----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=SWwQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210309' into staging
Aspeed patches :
* New model for the Aspeed LPC controller
* Misc cleanups
# gpg: Signature made Tue 09 Mar 2021 11:54:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210309:
hw/misc: Model KCS devices in the Aspeed LPC controller
hw/misc: Add a basic Aspeed LPC controller model
hw/arm: ast2600: Correct the iBT interrupt ID
hw/arm: ast2600: Set AST2600_MAX_IRQ to value from datasheet
hw/arm: ast2600: Force a multiple of 32 of IRQs for the GIC
hw/arm/aspeed: Fix location of firmware images in documentation
arm/ast2600: Fix SMP booting with -kernel
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the exception of hw/core/, the hw/ directory only contains
device models used in system emulation. Semihosting is also used
by user emulation. As a generic feature, move it out of hw/ directory.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210226131356.3964782-3-f4bug@amsat.org>
Message-Id: <20210305135451.15427-3-alex.bennee@linaro.org>
We want to move the semihosting code out of hw/ in the next patch.
This patch contains the mechanical steps, created using:
$ git mv include/hw/semihosting/ include/
$ sed -i s,hw/semihosting,semihosting, $(git grep -l hw/semihosting)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210226131356.3964782-2-f4bug@amsat.org>
Message-Id: <20210305135451.15427-2-alex.bennee@linaro.org>
Hypervisors, especially type-1 ones, need the firmware/bootcode to put
their initial guest somewhere in memory and pass the information to it
via platform data. The guest-loader is modelled after the generic
loader for exactly this sort of purpose:
$QEMU $ARGS -kernel ~/xen.git/xen/xen \
-append "dom0_mem=1G,max:1G loglvl=all guest_loglvl=all" \
-device guest-loader,addr=0x42000000,kernel=Image,bootargs="root=/dev/sda2 ro console=hvc0 earlyprintk=xen" \
-device guest-loader,addr=0x47000000,initrd=rootfs.cpio
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-5-alex.bennee@linaro.org>
This is a mechanical change to make the fdt available through
MachineState.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-3-alex.bennee@linaro.org>
The use of FDT's is quite common across our various platforms. To
allow the guest loader to tweak it we need to make it available in
the generic state. This creates the field and migrates the initial
user to use the generic field. Other boards will be updated in later
patches.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-2-alex.bennee@linaro.org>
* Add new mps3-an547 board
* target/arm: Restrict v7A TCG cpus to TCG accel
* Implement a Xilinx CSU DMA model
* hw/timer/renesas_tmr: Fix use of uninitialized data in read_tcnt()
-----BEGIN PGP SIGNATURE-----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=Qu2a
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210310' into staging
target-arm queue:
* Add new mps3-an547 board
* target/arm: Restrict v7A TCG cpus to TCG accel
* Implement a Xilinx CSU DMA model
* hw/timer/renesas_tmr: Fix use of uninitialized data in read_tcnt()
# gpg: Signature made Wed 10 Mar 2021 13:56:20 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210310: (54 commits)
hw/timer/renesas_tmr: Fix use of uninitialized data in read_tcnt()
hw/timer/renesas_tmr: Prefix constants for CSS values with CSS_
hw/ssi: xilinx_spips: Remove DMA related dead codes from zynqmp_spips
hw/ssi: xilinx_spips: Clean up coding convention issues
hw/arm: xlnx-zynqmp: Connect a Xilinx CSU DMA module for QSPI
hw/arm: xlnx-zynqmp: Clean up coding convention issues
hw/dma: Implement a Xilinx CSU DMA model
target/arm: Restrict v7A TCG cpus to TCG accel
tests/qtest/sse-timer-test: Test counter scaling changes
tests/qtest/sse-timer-test: Test the system timer
tests/qtest/sse-timer-test: Add simple test of the SSE counter
docs/system/arm/mps2.rst: Document the new mps3-an547 board
hw/arm/mps2-tz: Add new mps3-an547 board
hw/arm/mps2-tz: Make initsvtor0 setting board-specific
hw/arm/mps2-tz: Support running APB peripherals on different clock
hw/misc/mps2-scc: Implement changes for AN547
hw/misc/mps2-fpgaio: Support AN547 DBGCTRL register
hw/misc/mps2-fpgaio: Fold counters subsection into main vmstate
hw/arm/mps2-tz: Make UART overflow IRQ board-specific
hw/arm/armsse: Add SSE-300 support
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The read_tcnt() function calculates the TCNT register values for the
two channels of the timer module; it sets these up in the local
tcnt[] array, and eventually returns either one or both of them,
depending on whether the access is 8 or 16 bits. However, not all of
the code paths through this function set both elements of this array:
if the guest has programmed the TCCR.CSS register fields to values
which are either documented as not to be used or which QEMU does not
implement, then the function will return uninitialized data. (This
was spotted by Coverity.)
Add the missing CSS cases to this code, so that we return a
consistent value instead of uninitialized data, and so the code
structure indicates what's happening.
Fixes: CID 1429976
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219223241.16344-3-peter.maydell@linaro.org
The #defines INTERNAL and CASCADING represent different possible
values for the TCCR.CSS register field; prefix them with CSS_ to make
this more obvious, before we add more defines to represent the
other possible values of the field in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219223241.16344-2-peter.maydell@linaro.org
Now that the Xilinx CSU DMA model is implemented, the existing
DMA related dead codes in the ZynqMP QSPI are useless and should
be removed. The maximum register number is also updated to only
include the QSPI registers.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-6-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xilinx_spips.c,
as reported by:
$ ./scripts/checkpatch.pl hw/ssi/xilinx_spips.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-5-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a Xilinx CSU DMA module to ZynqMP SoC, and connent the stream
link of GQSPI to CSU DMA.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Recent changes allowed the pSeries machine to rollback the hotunplug
process for the DIMM when the guest kernel signals, via a
reconfiguration of the DR connector, that it's not going to release the
LMBs.
Let's also warn QAPI listerners about it. One place to do it would be
right after the unplug state is cleaned up,
spapr_clear_pending_dimm_unplug_state(). This would mean that the
function is now doing more than cleaning up the pending dimm state
though.
This patch does the following changes in spapr.c:
- send a QAPI event to inform that we experienced a failure in the
hotunplug of the DIMM;
- rename spapr_clear_pending_dimm_unplug_state() to
spapr_memory_unplug_rollback(). This is a better fit for what the
function is now doing, and it makes callers care more about what the
function goal is and less about spapr.c internals such as clearing
the pending dimm unplug state.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210302141019.153729-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We are asserting the existence of the first DRC LMB after sending unplug
requests to all LMBs of the DIMM, where every DRC is being asserted
inside the loop. This means that the first DRC is being asserted twice.
Remove the duplicated assert.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210302141019.153729-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pSeries machine is using QEMUTimer internals to return the timeout
in seconds for a timer object, in hw/ppc/spapr.c, function
spapr_drc_unplug_timeout_remaining_sec().
Create a helper in qemu-timer.c to retrieve the deadline for a QEMUTimer
object, in ms, to avoid exposing timer internals to the PPC code.
CC: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210301124133.23800-2-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Hotunplug for all other devices are warning the user when the hotunplug
is already in progress. Do the same for PCI devices in
spapr_pci_unplug_request().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210226163301.419727-5-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Both CPU hotunplug and PC_DIMM unplug reports an user warning,
mentioning that the hotunplug is in progress, if consecutive
'device_del' are issued in quick succession.
Do the same for PHBs in spapr_phb_unplug_request().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210226163301.419727-4-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The eTSEC node should provide an empty <ranges> property in the
eTSEC node, otherwise of_translate_address() in the Linux kernel
fails to get the eTSEC register base, reporting:
OF: ** translation for device /platform@f00000000/ethernet@0/queue-group **
OF: bus is default (na=1, ns=1) on /platform@f00000000/ethernet@0
OF: translating address: 00000000
OF: parent bus is default (na=1, ns=1) on /platform@f00000000
OF: no ranges; cannot translate
Per devicetree spec v0.3 [1] chapter 2.3.8:
If the property is not present in a bus node, it is assumed that
no mapping exists between children of the node and the parent
address space.
This is why of_translate_address() aborts the address translation.
Apparently U-Boot devicetree parser seems to be tolerant with
missing <ranges> as this was not noticed when testing with U-Boot.
The empty <ranges> property is present in all kernel shipped dtsi
files for eTSEC, Let's add it to conform with the spec.
[1] https://github.com/devicetree-org/devicetree-specification/releases/download/v0.3/devicetree-specification-v0.3.pdf
Fixes: fdfb7f2cdb ("e500: Add support for eTSEC in device tree")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <1614158919-9473-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
"qemu-common.h" should be included to provide the forward declaration
of qemu_hexdump() when HEX_DUMP is on.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210228050431.24647-1-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Handling errors in memory hotunplug in the pSeries machine is more
complex than any other device type, because there are all the
complications that other devices has, and more.
For instance, determining a timeout for a DIMM hotunplug must consider
if it's a Hash-MMU or a Radix-MMU guest, because Hash guests takes
longer to hotunplug DIMMs. The size of the DIMM is also a factor, given
that longer DIMMs naturally takes longer to be hotunplugged from the
kernel. And there's also the guest memory usage to be considered: if
there's a process that is consuming memory that would be lost by the
DIMM unplug, the kernel will postpone the unplug process until the
process finishes, and then initiate the regular hotunplug process. The
first two considerations are manageable, but the last one is a deal
breaker.
There is no sane way for the pSeries machine to determine the memory
load in the guest when attempting a DIMM hotunplug - and even if there
was a way, the guest can start using all the RAM in the middle of the
unplug process and invalidate our previous assumptions - and in result
we can't even begin to calculate a timeout for the operation. This means
that we can't implement a viable timeout mechanism for memory unplug in
pSeries.
Going back to why we would consider an unplug timeout, the reason is
that we can't know if the kernel is giving up the unplug. Turns out
that, sometimes, we can. Consider a failed memory hotunplug attempt
where the kernel will error out with the following message:
'pseries-hotplug-mem: Memory indexed-count-remove failed, adding any
removed LMBs'
This happens when there is a LMB that the kernel gave up in removing,
and the LMBs previously marked for removal are now being added back.
This happens in the pseries kernel in [1], dlpar_memory_remove_by_ic()
into dlpar_add_lmb(), and after that update_lmb_associativity_index().
In this function, the kernel is configuring the LMB DRC connector again.
Note that this is a valid usage in LOPAR, as stated in section
"ibm,configure-connector RTAS Call":
'A subsequent sequence of calls to ibm,configure-connector with the same
entry from the “ibm,drc-indexes” or “ibm,drc-info” property will restart
the configuration of devices which were not completely configured.'
We can use this kernel behavior in our favor. If a DRC connector
reconfiguration for a LMB that we marked as unplug pending happens, this
indicates that the kernel changed its mind about the unplug and is
reasserting that it will keep using all the LMBs of the DIMM. In this
case, it's safe to assume that the whole DIMM device unplug was
cancelled.
This patch hops into rtas_ibm_configure_connector() and, in the scenario
described above, clear the unplug state for the DIMM device. This will
not solve all the problems we still have with memory unplug, but it will
cover this case where the kernel reconfigures LMBs after a failed
unplug. We are a bit more resilient, without using an unreliable
timeout, and we didn't make the remaining error cases any worse.
[1] arch/powerpc/platforms/pseries/hotplug-memory.c
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-6-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is a reliable way to make a CPU hotunplug fail in the pseries
machine. Hotplug a CPU A, then offline all other CPUs inside the guest
but A. When trying to hotunplug A the guest kernel will refuse to do it,
because A is now the last online CPU of the guest. PAPR has no 'error
callback' in this situation to report back to the platform, so the guest
kernel will deny the unplug in silent and QEMU will never know what
happened. The unplug pending state of A will remain until the guest is
shutdown or rebooted.
Previous attempts of fixing it (see [1] and [2]) were aimed at trying to
mitigate the effects of the problem. In [1] we were trying to guess
which guest CPUs were online to forbid hotunplug of the last online CPU
in the QEMU layer, avoiding the scenario described above because QEMU is
now failing in behalf of the guest. This is not robust because the last
online CPU of the guest can change while we're in the middle of the
unplug process, and our initial assumptions are now invalid. In [2] we
were accepting that our unplug process is uncertain and the user should
be allowed to spam the IRQ hotunplug queue of the guest in case the CPU
hotunplug fails.
This patch presents another alternative, using the timeout
infrastructure introduced in the previous patch. CPU hotunplugs in the
pSeries machine will now timeout after 15 seconds. This is a long time
for a single CPU unplug to occur, regardless of guest load - although
the user is *strongly* encouraged to *not* hotunplug devices from a
guest under high load - and we can be sure that something went wrong if
it takes longer than that for the guest to release the CPU (the same
can't be said about memory hotunplug - more on that in the next patch).
Timing out the unplug operation will reset the unplug state of the CPU
and allow the user to try it again, regardless of the error situation
that prevented the hotunplug to occur. Of all the not so pretty
fixes/mitigations for CPU hotunplug errors in pSeries, timing out the
operation is an admission that we have no control in the process, and
must assume the worst case if the operation doesn't succeed in a
sensible time frame.
[1] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg03353.html
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg04400.html
Reported-by: Xujun Ma <xuma@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1911414
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-5-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LoPAR spec provides no way for the guest kernel to report failure of
hotplug/hotunplug events. This wouldn't be bad if those operations were
granted to always succeed, but that's far for the reality.
What ends up happening is that, in the case of a failed hotunplug,
regardless of whether it was a QEMU error or a guest misbehavior, the
pSeries machine is retaining the unplug state of the device in the
running guest. This state is cleanup in machine reset, where it is
assumed that this state represents a device that is pending unplug, and
the device is hotunpluged from the board. Until the reset occurs, any
hotunplug operation of the same device is forbid because there is a
pending unplug state.
This behavior has at least one undesirable side effect. A long standing
pending unplug state is, more often than not, the result of a hotunplug
error. The user had to dealt with it, since retrying to unplug the
device is noy allowed, and then in the machine reset we're removing the
device from the guest. This means that we're failing the user twice -
failed to hotunplug when asked, then hotunplugged without notice.
Solutions to this problem range between trying to predict when the
hotunplug will fail and forbid the operation from the QEMU layer, from
opening up the IRQ queue to allow for multiple hotunplug attempts, from
telling the users to 'reboot the machine if something goes wrong'. The
first solution is flawed because we can't fully predict guest behavior
from QEMU, the second solution is a trial and error remediation that
counts on a hope that the unplug will eventually succeed, and the third
is ... well.
This patch introduces a crude, but effective solution to hotunplug
errors in the pSeries machine. For each unplug done, we'll timeout after
some time. If a certain amount of time passes, we'll cleanup the
hotunplug state from the machine. During the timeout period, any unplug
operations in the same device will still be blocked. After that, we'll
assume that the guest failed the operation, and allow the user to try
again. If the timeout is too short we'll prevent legitimate hotunplug
situations to occur, so we'll need to overestimate the regular time an
unplug operation takes to succeed to account that.
The true solution for the hotunplug errors in the pSeries machines is a
PAPR change to allow for the guest to warn the platform about it. For
now, the work done in this timeout design can be used for the new PAPR
'abort hcall' in the future, given that for both cases we'll need code
to cleanup the existing unplug states of the DRCs.
At this moment we're adding the basic wiring of the timer into the DRC.
Next patch will use the timer to timeout failed CPU hotunplugs.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_drc_detach() is not the best name for what the function does. The
function does not detach the DRC, it makes an uncommited attempt to do
it. It'll mark the DRC as pending unplug, via the 'unplug_request'
flag, and only if the DRC state is drck->empty_state it will detach the
DRC, via spapr_drc_release().
This is a contrast with its pair spapr_drc_attach(), where the function
is indeed creating the DRC QOM object. If you know what
spapr_drc_attach() does, you can be misled into thinking that
spapr_drc_detach() is removing the DRC from QEMU internal state, which
isn't true.
The current role of this function is better described as a request for
detach, since there's no guarantee that we're going to detach the DRC in
the end. Rename the function to spapr_drc_unplug_request to reflect
what is is doing.
The initial idea was to change the name to spapr_drc_detach_request(),
and later on change the unplug_request flag to detach_request. However,
unplug_request is a migratable boolean for a long time now and renaming
it is not worth the trouble. spapr_drc_unplug_request() setting
drc->unplug_request is more natural than spapr_drc_detach_request
setting drc->unplug_request.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When moving a physical DRC to "Available", drc_isolate_physical() will
move the DRC state to STATE_PHYSICAL_POWERON and, if the DRC is marked
for unplug, call spapr_drc_detach(). For physical DRCs,
drck->empty_state is STATE_PHYSICAL_POWERON, meaning that we're sure
that spapr_drc_detach() will end up calling spapr_drc_release() in the
end.
Likewise, for logical DRCs, drc_set_unusable will move the DRC to
"Unusable" state, setting drc->state to STATE_LOGICAL_UNUSABLE, which is
the drck->empty_state for logical DRCs. spapr_drc_detach() will call
spapr_drc_release() in this case as well.
In both scenarios, spapr_drc_detach() is being used as a
spapr_drc_release(), wrapper, where we also set unplug_requested (which
is already true, otherwise spapr_drc_detach() wouldn't be called in the
first place) and check if drc->state == drck->empty_state, which we also
know it's guaranteed to be true because we just set it.
Just use spapr_drc_release() in these functions to be clear of our
intentions in both these functions.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
drc_isolate_logical() is used to move the DRC from the "Configured" to
the "Available" state, erroring out if the DRC is in the unexpected
"Unisolate" state and doing nothing (with RTAS_OUT_SUCCESS) if the DRC
is already in "Available" or in "Unusable" state.
When moving from "Configured" to "Available", the DRC is moved to the
LOGICAL_AVAILABLE state, a drc->unplug_requested check is done and, if
true, spapr_drc_detach() is called.
What spapr_drc_detach() does then is:
- set drc->unplug_requested to true. In fact, this is the only place
where unplug_request is set to true;
- does nothing else if drc->state != drck->empty_state. If the DRC
state is equal to drck->empty_state, spapr_drc_release() is
called. For logical DRCs, drck->empty_state = LOGICAL_UNUSABLE.
In short, calling spapr_drc_detach() in drc_isolate_logical() does
nothing. It'll set unplug_request to true again ('again' since it was
already true - otherwise the function wouldn't be called), and will
return without calling spapr_drc_release() because the DRC is not in
LOGICAL_UNUSABLE, since drc_isolate_logical() just moved it to
LOGICAL_AVAILABLE. The only place where the logical DRC is released is
when called from drc_set_unusable(), when it is moved to the
"Unusable" state. As it should, according to PAPR.
Even though calling spapr_drc_detach() in drc_isolate_logical() is
benign, removing it will avoid further thought about the matter. So
let's go ahead and do that.
As a note, this logic was introduced in commit bbf5c878ab. Since
then, the DRC handling code was refactored and enhanced, and PAPR
itself went through some changes in the DRC area as well. It is
expected that some assumptions we had back then are now deprecated.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210211225246.17315-2-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We no longer need to include sm501_template.h multiple times, so
we can simply inline its contents into sm501.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-4-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that we only include sm501_template.h for the DEPTH==32 case, we
can expand out the uses of the BPP, PIXEL_TYPE and PIXEL_NAME macros
in that header.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-3-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the sm501 display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-2-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Milkymist board requires more than the PTIMER. Directly
select the LM32_DEVICES. This fixes:
/usr/bin/ld:
libqemu-lm32-softmmu.fa.p/target_lm32_gdbstub.c.o: in function `lm32_cpu_gdb_read_register':
target/lm32/gdbstub.c:46: undefined reference to `lm32_pic_get_im'
target/lm32/gdbstub.c:48: undefined reference to `lm32_pic_get_ip'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_im':
target/lm32/op_helper.c:107: undefined reference to `lm32_pic_set_im'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_ip':
target/lm32/op_helper.c:114: undefined reference to `lm32_pic_set_ip'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_jtx':
target/lm32/op_helper.c:120: undefined reference to `lm32_juart_set_jtx'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_jrx':
target/lm32/op_helper.c:125: undefined reference to `lm32_juart_set_jrx'
libqemu-lm32-softmmu.fa.p/target_lm32_translate.c.o: in function `lm32_cpu_dump_state':
target/lm32/translate.c:1161: undefined reference to `lm32_pic_get_ip'
target/lm32/translate.c:1161: undefined reference to `lm32_pic_get_im'
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210221225626.2589247-4-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We want to be able to use the 'LM32' config for architecture
specific features. As CONFIG_LM32 is only used to select
peripherals, rename it CONFIG_LM32_DEVICES.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210221225626.2589247-3-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We want to be able to use the 'LM32' config for architecture
specific features. Introduce CONFIG_LM32_EVR to select the
lm32-evr / lm32-uclinux boards.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210221225626.2589247-2-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We forward-declare Object typedef in "qemu/typedefs.h" since commit
ca27b5eb7c ("qom/object: Move Object typedef to 'qemu/typedefs.h'").
Use it everywhere to make the code simpler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210225182003.3629342-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
On Fedora 33, gcc 10.2.1 notes that scsi_cdb_length(buf) can set
len==-1, which in turn overflows g_malloc():
[5/5] Linking target qemu-system-x86_64
In function ‘scsi_disk_new_request_dump’,
inlined from ‘scsi_new_request’ at ../hw/scsi/scsi-disk.c:2608:9:
../hw/scsi/scsi-disk.c:2582:19: warning: argument 1 value ‘18446744073709551612’ exceeds maximum object size 9223372036854775807 [-Walloc-size-larger-than=]
2582 | line_buffer = g_malloc(len * 5 + 1);
| ^
Silence it with a decent assertion, since we only convert a buffer to
bytes when we have a valid cdb length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210209152350.207958-1-eblake@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
An assorted set of spelling fixes in various places.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210309111510.79495-1-mjt@msgid.tls.msk.ru>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAmBEwfEeHG1hcmsuY2F2
ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIfYZYH/AwOuqycV9XI1s3K
valsExtSmcj6oTrFTSyak0U7QL9G5pm40qEHwQkwFwYecaQXfFNMN1Mt4gYpsLai
JNhV29tzWrQtNFepCjvvuJihDY5IC/3NWyrWqYXRNZ5IGMvde3HUcg210bFOC3mf
iOtZ40ZjBspTwG4eJCOLBBDeXVAMkVUjdfqtsq66zGteHsJjNEpso0HLdMvlFkud
QLF4g06h8iFMxwahZYEwY+fKUHphqfZn8INr01ODQIy3nBGVgenKz9DKPw/pg/UD
nfxhuYwftDof65JpYEhClOWas3AztFJ1YyyP/cibwosLBQVphj3R05/kF6VuyuyP
gZjux0w=
=RPt3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mcayland/tags/qemu-sparc-20210307' into staging
qemu-sparc queue
# gpg: Signature made Sun 07 Mar 2021 12:07:13 GMT
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* remotes/mcayland/tags/qemu-sparc-20210307: (42 commits)
esp: add support for unaligned accesses
esp: implement non-DMA transfers in PDMA mode
esp: add trivial implementation of the ESP_RFLAGS register
esp: convert cmdbuf from array to Fifo8
esp: convert ti_buf from array to Fifo8
esp: transition to message out phase after SATN and stop command
esp: add maxlen parameter to get_cmd()
esp: raise interrupt after every non-DMA byte transferred to the FIFO
esp: remove old deferred command completion mechanism
esp: defer command completion interrupt on incoming data transfers
esp: latch individual bits in ESP_RINTR register
esp: implement FIFO flush command
esp: add 4 byte PDMA read and write transfers
esp: remove pdma_origin from ESPState
esp: use FIFO for PDMA transfers between initiator and device
esp: fix PDMA target selection
esp: rename get_cmd_cb() to esp_select()
esp: remove CMD pdma_origin
esp: use in-built TC to determine PDMA transfer length
esp: use ti_wptr/ti_rptr to manage the current FIFO position for PDMA
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2600 allocates distinct GIC IRQs for the LPC subdevices such as
the iBT device. Previously on the AST2400 and AST2500 the LPC subdevices
shared a single LPC IRQ.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-4-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The datasheet says we have 197 IRQs allocated, and we need more than 128
to describe IRQs from LPC devices. Raise the value now to allow
modelling of the LPC devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This appears to be a requirement of the GIC model. The AST2600 allocates
197 GIC IRQs, which we will adjust shortly.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ast2600 machines do not have PSCI firmware, so this property should
have never been set. Removing this node fixes SMP booting Linux kernels
that have PSCI enabled, as Linux fails to find PSCI in the device tree
and falls back to the soc-specific method for enabling secondary CPUs.
The comment is out of date as Qemu has supported -kernel booting since
9bb6d14081 ("aspeed: Add boot stub for smp booting"), in v5.1.
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210303010505.635621-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Support Identify command for Namespace attached controller list. This
command handler will traverse the controller instances in the given
subsystem to figure out whether the specified nsid is attached to the
controllers or not.
The 4096bytes Identify data will return with the first entry (16bits)
indicating the number of the controller id entries. So, the data can
hold up to 2047 entries for the controller ids.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
[k.jensen: rebased for dma refactor]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If namespace inventory is changed due to some reasons (e.g., namespace
attachment/detachment), controller can send out event notifier to the
host to manage namespaces.
This patch sends out the AEN to the host after either attach or detach
namespaces from controllers. To support clear of the event from the
controller, this patch also implemented Get Log Page command for Changed
Namespace List log type. To return namespace id list through the
command, when namespace inventory is updated, id is added to the
per-controller list (changed_ns_list).
To indicate the support of this async event, this patch set
OAES(Optional Asynchronous Events Supported) in Identify Controller data
structure.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch supports Namespace Attachment command for the pre-defined
nvme-ns device nodes. Of course, attach/detach namespace should only be
supported in case 'subsys' is given. This is because if we detach a
namespace from a controller, somebody needs to manage the detached, but
allocated namespace in the NVMe subsystem.
As command effect for the namespace attachment command is registered,
the host will be notified that namespace inventory is changed so that
host will rescan the namespace inventory after this command. For
example, kernel driver manages this command effect via passthru IOCTL.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
[k.jensen: rebased for dma refactor]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch has no functional changes. This patch just refactored
nvme_select_ns_iocs() to iterate the attached namespaces of the
controlller and make it invoke __nvme_select_ns_iocs().
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
From NVMe spec 1.4b "6.1.5. NSID and Namespace Relationships" defines
valid namespace types:
- Unallocated: Not exists in the NVMe subsystem
- Allocated: Exists in the NVMe subsystem
- Inactive: Not attached to the controller
- Active: Attached to the controller
This patch added support for allocated, but not attached namespace type:
!nvme_ns(n, nsid) && nvme_subsys_ns(n->subsys, nsid)
nvme_ns() returns attached namespace instance of the given controller
and nvme_subsys_ns() returns allocated namespace instance in the
subsystem.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Expand allocated namespace list (subsys->namespaces) to have 256 entries
which is a value lager than at least NVME_MAX_NAMESPACES which is for
attached namespace list in a controller.
Allocated namespace list should at least larger than attached namespace
list.
n->num_namespaces = NVME_MAX_NAMESPACES;
The above line will set the NN field by id->nn so that the subsystem
should also prepare at least this number of namespace list entries.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
subsys->namespaces array used to be sized to NVME_SUBSYS_MAX_NAMESPACES.
But subsys->namespaces are being accessed with 1-based namespace id
which means the very first array entry will always be empty(NULL).
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Given that now we have nvme-subsys device supported, we can manage
namespace allocated, but not attached: detached. This patch introduced
a parameter for nvme-ns device named 'detached'. This parameter
indicates whether the given namespace device is detached from
a entire NVMe subsystem('subsys' given case, shared namespace) or a
controller('bus' given case, private namespace).
- Allocated namespace
1) Shared ns in the subsystem 'subsys0':
-device nvme-ns,id=ns1,drive=blknvme0,nsid=1,subsys=subsys0,detached=true
2) Private ns for the controller 'nvme0' of the subsystem 'subsys0':
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
-device nvme-ns,id=ns1,drive=blknvme0,nsid=1,bus=nvme0,detached=true
3) (Invalid case) Controller 'nvme0' has no subsystem to manage ns:
-device nvme,serial=foo,id=nvme0
-device nvme-ns,id=ns1,drive=blknvme0,nsid=1,bus=nvme0,detached=true
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The nvme_dma function doesn't just do DMA (QEMUSGList-based) memory transfers;
it also handles QEMUIOVector copies.
Introduce the NvmeTxDirection enum and rename to nvme_tx. Remove mapping
of PRPs/SGLs from nvme_tx and instead assert that they have been mapped
previously. This allows more fine-grained use in subsequent patches.
Add new (better named) helpers, nvme_{c2h,h2c}, that does both PRP/SGL
mapping and transfer.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The PRP and SGL mapping functions does not have any particular need for
the entire NvmeRequest as a parameter. Clean it up.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Introduce NvmeSg and try to deal with that pesky qsg/iov duality that
haunts all the memory-related functions.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
A Write Zeroes commands should not be counted in either the 'Data Units
Written' or in 'Host Write Commands' SMART/Health Information Log page.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The 'len' member of the nvme_compare_ctx struct is redundant since the
same information is available in the 'iov' member.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Dataset Management is not subject to MDTS, but exceeded a certain size
per range causes internal looping. Report this limit (DMRSL) in the NVM
command set specific identify controller data structure.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add a trace event for the offline zone condition when checking zone
read.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: split commit]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
assert may be compiled to a noop and we could end up returning an
uninitialized status.
Fix this by always returning Internal Device Error as a fallback.
Note that, as pointed out by Philippe, per commit 262a69f428 ("osdep.h:
Prohibit disabling assert() in supported builds") this shouldn't be
possible. But clean it up so we don't worry about it again.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: split commit]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add a trace event for the Identify command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Remove an unnecessary le_to_cpu conversion in Identify.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
ZASL (Zone Append Size Limit) is defined exactly like MDTS (Maximum Data
Transfer Size), that is, it is a value in units of the minimum memory
page size (CAP.MPSMIN) and is reported as a power of two.
The 'mdts' nvme device parameter is specified as in the spec, but the
'zoned.append_size_limit' parameter is specified in bytes. This is
suboptimal for a number of reasons:
1. It is just plain confusing wrt. the definition of mdts.
2. There is a lot of complexity involved in validating the value; it
must be a power of two, it should be larger than 4k, if it is zero
we set it internally to mdts, but still report it as zero.
3. While "hw/block/nvme: improve invalid zasl value reporting"
slightly improved the handling of the parameter, the validation is
still wrong; it does not depend on CC.MPS, it depends on
CAP.MPSMIN. And we are not even checking that it is actually less
than or equal to MDTS, which is kinda the *one* condition it must
satisfy.
Fix this by defining zasl exactly like mdts and checking the one thing
that it must satisfy (that it is less than or equal to mdts). Also,
change the default value from 128KiB to 0 (aka, whatever mdts is).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for using the broadcast nsid to issue a flush on all
namespaces through a single command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 6eb7a07129 ("hw/block/nvme: change controller pci id") changed
the controller to use a Red Hat assigned PCI Device and Vendor ID, but
did not change the IEEE OUI away from the Intel IEEE OUI.
Fix that and use the locally assigned QEMU IEEE OUI instead if the
`use-intel-id` parameter is not explicitly set. Also reverse the Intel
IEEE OUI bytes.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The Zone Append Size Limit (ZASL) must be at least 4096 bytes, so
improve the user experience by adding an early parameter check in
nvme_check_constraints.
When ZASL is still too small due to the host configuring the device for
an even larger page size, convert the trace point in nvme_start_ctrl to
an NVME_GUEST_ERR such that this is logged by QEMU instead of only
traced.
Reported-by: Corne <info@dantalion.nl>
Cc: Dmitry Fomichev <Dmitry.Fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Firstly, if zoned.max_active is non-zero, zoned.max_open must be less
than or equal to zoned.max_active.
Secondly, if only zones.max_active is set, we have to explicitly set
zones.max_open or we end up with an invalid MAR/MOR configuration. This
is an artifact of the parameters not being zeroes-based like in the
spec.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reported-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Implicitly and Explicitly Open zones can be closed by Close Zone
management function. This got broken by a recent commit ("hw/block/nvme:
refactor zone resource management") and now such commands fail with
Invalid Zone State Transition status.
Modify nvm_zrm_close() function to make Close Zone work correctly.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for TP 4065a ("Simple Copy Command"), v2020.05.04
("Ratified").
The implementation uses a bounce buffer to first read in the source
logical blocks, then issue a write of that bounce buffer. The default
maximum number of source logical blocks is 128, translating to 512 KiB
for 4k logical blocks which aligns with the default value of MDTS.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
In preparation for Simple Copy, pull write pointer advancement into a
separate function that is independent off an NvmeRequest.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Zone transition handling and resource management is open coded (and
semi-duplicated in the case of open, close and finish).
In preparation for Simple Copy command support (which also needs to open
zones for writing), consolidate into a set of 'nvme_zrm' functions and
in the process fix a bug with the controller not closing an open zone to
allow another zone to be explicitly opened.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Remove the unused NvmeCtrl parameter in nvme_check_zone_write.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
nvme-ns device is registered to a nvme controller device during the
initialization in nvme_register_namespace() in case that 'bus' property
is given which means it's mapped to a single controller.
This patch introduced a new property 'subsys' just like the controller
device instance did to map a namespace to a NVMe subsystem.
If 'subsys' property is given to the nvme-ns device, it will belong to
the specified subsystem and will be attached to all controllers in that
subsystem by enabling shared namespace capability in NMIC(Namespace
Multi-path I/O and Namespace Capabilities) in Identify Namespace.
Usage:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
-device nvme,serial=bar,id=nvme1,subsys=subsys0
-device nvme,serial=baz,id=nvme2,subsys=subsys0
-device nvme-ns,id=ns1,drive=<drv>,nsid=1,subsys=subsys0 # Shared
-device nvme-ns,id=ns2,drive=<drv>,nsid=2,bus=nvme2 # Non-shared
In the above example, 'ns1' will be shared to 'nvme0' and 'nvme1' in
the same subsystem. On the other hand, 'ns2' will be attached to the
'nvme2' only as a private namespace in that subsystem.
All the namespace with 'subsys' parameter will attach all controllers in
the subsystem to the namespace by default.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
We have nvme-subsys and nvme devices mapped together. To support
multi-controller scheme to this setup, controller identifier(id) has to
be managed. Earlier, cntlid(controller id) used to be always 0 because
we didn't have any subsystem scheme that controller id matters.
This patch introduced 'cntlid' attribute to the nvme controller
instance(NvmeCtrl) and make it allocated by the nvme-subsys device
mapped to the controller. If nvme-subsys is not given to the
controller, then it will always be 0 as it was.
Added 'ctrls' array in the nvme-subsys instance to manage attached
controllers to the subsystem with a limit(32). This patch didn't take
list for the controllers to make it seamless with nvme-ns device.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme controller(nvme) can be mapped to a NVMe subsystem(nvme-subsys).
This patch maps a controller to a subsystem by adding a parameter
'subsys' to the nvme device.
To map a controller to a subsystem, we need to put nvme-subsys first and
then maps the subsystem to the controller:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
If 'subsys' property is not given to the nvme controller, then subsystem
NQN will be created with serial (e.g., 'foo' in above example),
Otherwise, it will be based on subsys id (e.g., 'subsys0' in above
example).
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
To support multi-path in QEMU NVMe device model, We need to have NVMe
subsystem hierarchy to map controllers and namespaces to a NVMe
subsystem.
This patch introduced a simple nvme-subsys device model. The subsystem
will be prepared with subsystem NQN with <subsys_id> provided in
nvme-subsys device:
ex) -device nvme-subsys,id=subsys0: nqn.2019-08.org.qemu:subsys0
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
[k.jensen: added 'nqn' device parameter per request]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ZynqMP QSPI supports SPI transfer using DMA mode, but currently this
is unimplemented. When QSPI is programmed to use DMA mode, QEMU will
crash. This is observed when testing VxWorks 7.
This adds a Xilinx CSU DMA model and the implementation is based on
https://github.com/Xilinx/qemu/blob/master/hw/dma/csu_stream_dma.c.
The DST part of the model is verified along with ZynqMP GQSPI model.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
Implement the minor changes required to the SCC block for AN547 images:
* CFG2 and CFG5 exist (like AN524)
* CFG3 is reserved (like AN524)
* CFG0 bit 1 is CPU_WAIT; we don't implement it, but note this
in the TODO comment
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-40-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
We've already broken migration compatibility for all the MPS
boards, so we might as well take advantage of this to simplify
the vmstate for the FPGAIO device by folding the counters
subsection into the main vmstate description.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-38-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
The SSE-200 and SSE-300 have different PID register values from the
IoTKit for the sysctl register block. We incorrectly implemented the
SSE-200 with the same PID values as IoTKit. Fix the SSE-200 bug and
report these register values for SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-19-peter.maydell@linaro.org
The sysctl PDCM_PD_*_SENSE registers control various power domains in
the system and allow the guest to configure which conditions keep a
power domain awake and what power state to use when the domain is in
a low power state. QEMU doesn't model power domains, so for us these
registers are dummy reads-as-written implementations.
The SSE-300 has a different power domain setup, so the set of
registers is slightly different:
Offset SSE-200 SSE-300
---------------------------------------------------
0x200 PDCM_PD_SYS_SENSE PDCM_PD_SYS_SENSE
0x204 reserved PDCM_PD_CPU0_SENSE
0x208 reserved reserved
0x20c PDCM_PD_SRAM0_SENSE reserved
0x210 PDCM_PD_SRAM1_SENSE reserved
0x214 PDCM_PD_SRAM2_SENSE PDCM_PD_VMR0_SENSE
0x218 PDCM_PD_SRAM3_SENSE PDCM_PD_VMR1_SENSE
Offsets 0x200 and 0x208 are the same for both, so handled in a
previous commit; here we deal with 0x204, 0x20c, 0x210, 0x214, 0x218.
(We can safely add new lines to the SSE300 vmstate because no board
uses this device in an SSE300 yet.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-18-peter.maydell@linaro.org
The SSE-300 has a new PWRCTRL register at offset 0x1fc (previously
reserved). This register controls accessibility of some registers
in the Power Policy Units (PPUs). Since QEMU doesn't implement
the PPUs, we don't need to implement any real behaviour for this
register, so we just handle the UNLOCK bit which controls whether
writes to the register itself are permitted and otherwise make it
be reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-17-peter.maydell@linaro.org
The SSE-300 has only one CPU and so no INITSVTOR1. It does
have INITSVTOR0, but unlike the SSE-200 this register now
has a LOCK bit which can be set to 1 to prevent any further
writes to the register. Implement these differences.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-16-peter.maydell@linaro.org
In the SSE-300 the CPU_WAIT and NMI_ENABLE registers have
moved offsets, so they are now where the SSE-200's WICCTRL
and EWCTRL were. The SSE-300 does not have WICCTLR or EWCTRL
at all, and the old offsets are reserved:
Offset SSE-200 SSE-300
-----------------------------------
0x118 CPUWAIT reserved
0x118 NMI_ENABLE reserved
0x120 WICCTRL CPUWAIT
0x124 EWCTRL NMI_ENABLE
Handle this reshuffle, and the fact that SSE-300 has only
one CPU and so only one active bit in CPUWAIT.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-15-peter.maydell@linaro.org
The SSE-300's iokit-sysctl device is similar to the SSE-200, but
some registers have moved address or have different behaviours.
In this commit we add case statements for the registers where
the SSE-300 and SSE-200 have the same behaviour. Some registers
are the same on all SSE versions and so need no code change at all.
Putting both of these categories together covers:
0x0 SECDBGSTAT
0x4 SECDBGSET
0x8 SECDBGCLR
0xc SCSECCTRL
0x10 CLK_CFG0 -- this is like SSE-200 FCLK_DIV but with a
different set of clocks being controlled; our implementation
is a dummy reads-as-written anyway
0x14 CLK_CFG1 -- similar to SSE-200 SYSCLK_DIV; our implementation
is a dummy
0x18 CLK_FORCE -- similar to SSE-200 but different bit allocations;
we have a dummy implementation
0x100 RESET_SYNDROME -- bit allocation differs from SSE-200 but our
implementation is a dummy
0x104 RESET_MASK -- bit allocation differs from SSE-200 but our
implementation is a dummy
0x108 SWRESET
0x10c GRETREG
0x200 PDCM_PD_SYS_SENSE -- some bit allocations differ, but our
implementation is a dummy
We also need to migrate the state of these registers which are shared
between the SSE-200 and SSE-300, so update the vmstate 'needed'
function to do this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-14-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
In the SSE-300, the format of the SYS_CONFIG0 register has changed again;
pass through the correct value to the SYSINFO register block device.
We drop the old SysConfigFormat enum, which was implemented in the
hope that different flavours of SSE would share the same format;
since they all seem to be different and we now have an sse_version
enum to key off, just use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-10-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
Remove the is_sse200 flag in favour of just directly testing the new
sse_version field.
Since some of these registers exist in the SSE-300 but some do not or
have different behaviour, we expand out the if() statements in the
read and write functions into switch()es, so we have an easy place to
put SSE-300 specific behaviour.
(Until we do add the SSE-300 behaviour, the thing preventing us
reaching the "unreachable" default cases is that armsse.c doesn't
yet pass us an ARMSSE_SSE300 version.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-7-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
Use the new clock_ns_to_ticks() function in npcm7xx_timer where
appropriate.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-5-peter.maydell@linaro.org
Volker Rümelin