Both functions are called by MemoryRegionOps.[read/write] handlers
with unsigned 'size' argument. Both functions call
pci_host_config_[read/write]_common() which expect a uint32_t 'len'
parameter (also unsigned).
Since it is pointless (and confuse) to use a signed value, use a
unsigned type.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191216002134.18279-3-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtqueue notifications are not necessary during polling, so we disable
them. This allows the guest driver to avoid MMIO vmexits.
Unfortunately the virtio-blk and virtio-scsi handler functions re-enable
notifications, defeating this optimization.
Fix virtio-blk and virtio-scsi emulation so they leave notifications
disabled. The key thing to remember for correctness is that polling
always checks one last time after ending its loop, therefore it's safe
to lose the race when re-enabling notifications at the end of polling.
There is a measurable performance improvement of 5-10% with the null-co
block driver. Real-life storage configurations will see a smaller
improvement because the MMIO vmexit overhead contributes less to
latency.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191209210957.65087-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the SLOF firmware for pseries guests will disable/re-enable
a PCI device multiple times via IO/MEM/MASTER bits of PCI_COMMAND
register after the initial probe/feature negotiation, as it tends to
work with a single device at a time at various stages like probing
and running block/network bootloaders without doing a full reset
in-between.
In QEMU, when PCI_COMMAND_MASTER is disabled we disable the
corresponding IOMMU memory region, so DMA accesses (including to vring
fields like idx/flags) will no longer undergo the necessary
translation. Normally we wouldn't expect this to happen since it would
be misbehavior on the driver side to continue driving DMA requests.
However, in the case of pseries, with iommu_platform=on, we trigger the
following sequence when tearing down the virtio-blk dataplane ioeventfd
in response to the guest unsetting PCI_COMMAND_MASTER:
#2 0x0000555555922651 in virtqueue_map_desc (vdev=vdev@entry=0x555556dbcfb0, p_num_sg=p_num_sg@entry=0x7fffe657e1a8, addr=addr@entry=0x7fffe657e240, iov=iov@entry=0x7fffe6580240, max_num_sg=max_num_sg@entry=1024, is_write=is_write@entry=false, pa=0, sz=0)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:757
#3 0x0000555555922a89 in virtqueue_pop (vq=vq@entry=0x555556dc8660, sz=sz@entry=184)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:950
#4 0x00005555558d3eca in virtio_blk_get_request (vq=0x555556dc8660, s=0x555556dbcfb0)
at /home/mdroth/w/qemu.git/hw/block/virtio-blk.c:255
#5 0x00005555558d3eca in virtio_blk_handle_vq (s=0x555556dbcfb0, vq=0x555556dc8660)
at /home/mdroth/w/qemu.git/hw/block/virtio-blk.c:776
#6 0x000055555591dd66 in virtio_queue_notify_aio_vq (vq=vq@entry=0x555556dc8660)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:1550
#7 0x000055555591ecef in virtio_queue_notify_aio_vq (vq=0x555556dc8660)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:1546
#8 0x000055555591ecef in virtio_queue_host_notifier_aio_poll (opaque=0x555556dc86c8)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:2527
#9 0x0000555555d02164 in run_poll_handlers_once (ctx=ctx@entry=0x55555688bfc0, timeout=timeout@entry=0x7fffe65844a8)
at /home/mdroth/w/qemu.git/util/aio-posix.c:520
#10 0x0000555555d02d1b in try_poll_mode (timeout=0x7fffe65844a8, ctx=0x55555688bfc0)
at /home/mdroth/w/qemu.git/util/aio-posix.c:607
#11 0x0000555555d02d1b in aio_poll (ctx=ctx@entry=0x55555688bfc0, blocking=blocking@entry=true)
at /home/mdroth/w/qemu.git/util/aio-posix.c:639
#12 0x0000555555d0004d in aio_wait_bh_oneshot (ctx=0x55555688bfc0, cb=cb@entry=0x5555558d5130 <virtio_blk_data_plane_stop_bh>, opaque=opaque@entry=0x555556de86f0)
at /home/mdroth/w/qemu.git/util/aio-wait.c:71
#13 0x00005555558d59bf in virtio_blk_data_plane_stop (vdev=<optimized out>)
at /home/mdroth/w/qemu.git/hw/block/dataplane/virtio-blk.c:288
#14 0x0000555555b906a1 in virtio_bus_stop_ioeventfd (bus=bus@entry=0x555556dbcf38)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-bus.c:245
#15 0x0000555555b90dbb in virtio_bus_stop_ioeventfd (bus=bus@entry=0x555556dbcf38)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-bus.c:237
#16 0x0000555555b92a8e in virtio_pci_stop_ioeventfd (proxy=0x555556db4e40)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-pci.c:292
#17 0x0000555555b92a8e in virtio_write_config (pci_dev=0x555556db4e40, address=<optimized out>, val=1048832, len=<optimized out>)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-pci.c:613
I.e. the calling code is only scheduling a one-shot BH for
virtio_blk_data_plane_stop_bh, but somehow we end up trying to process
an additional virtqueue entry before we get there. This is likely due
to the following check in virtio_queue_host_notifier_aio_poll:
static bool virtio_queue_host_notifier_aio_poll(void *opaque)
{
EventNotifier *n = opaque;
VirtQueue *vq = container_of(n, VirtQueue, host_notifier);
bool progress;
if (!vq->vring.desc || virtio_queue_empty(vq)) {
return false;
}
progress = virtio_queue_notify_aio_vq(vq);
namely the call to virtio_queue_empty(). In this case, since no new
requests have actually been issued, shadow_avail_idx == last_avail_idx,
so we actually try to access the vring via vring_avail_idx() to get
the latest non-shadowed idx:
int virtio_queue_empty(VirtQueue *vq)
{
bool empty;
...
if (vq->shadow_avail_idx != vq->last_avail_idx) {
return 0;
}
rcu_read_lock();
empty = vring_avail_idx(vq) == vq->last_avail_idx;
rcu_read_unlock();
return empty;
but since the IOMMU region has been disabled we get a bogus value (0
usually), which causes virtio_queue_empty() to falsely report that
there are entries to be processed, which causes errors such as:
"virtio: zero sized buffers are not allowed"
or
"virtio-blk missing headers"
and puts the device in an error state.
This patch works around the issue by introducing virtio_set_disabled(),
which sets a 'disabled' flag to bypass checks like virtio_queue_empty()
when bus-mastering is disabled. Since we'd check this flag at all the
same sites as vdev->broken, we replace those checks with an inline
function which checks for either vdev->broken or vdev->disabled.
The 'disabled' flag is only migrated when set, which should be fairly
rare, but to maintain migration compatibility we disable it's use for
older machine types. Users requiring the use of the flag in conjunction
with older machine types can set it explicitly as a virtio-device
option.
NOTES:
- This leaves some other oddities in play, like the fact that
DRIVER_OK also gets unset in response to bus-mastering being
disabled, but not restored (however the device seems to continue
working)
- Similarly, we disable the host notifier via
virtio_bus_stop_ioeventfd(), which seems to move the handling out
of virtio-blk dataplane and back into the main IO thread, and it
ends up staying there till a reset (but otherwise continues working
normally)
Cc: David Gibson <david@gibson.dropbear.id.au>,
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Message-Id: <20191120005003.27035-1-mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Devices tend to maintain vq pointers, allow deleting them trough a vq pointer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Now that the old pc-0.x machine types have been removed, this config
knob is not required anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209125248.5849-4-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the PCII440FXState structure public, so it can be used out of
this source file. This will allow us to extract the IGD Passthrough
Host Bridge, which is a children of the TYPE_I440FX_PCI_DEVICE.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209095002.32194-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This device is only used by the PC machines. The pc.c file is
already big enough, with 2255 lines. By removing 113 lines of
it, we reduced it by 5%. It is now a bit easier to navigate
the file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The irq number is unsigned; we reject negative values. But -1
is used for the isairq array, which is declared unsigned! And
since we have a definition for the number of ISA IRQs, use it.
Based on a patch by Philippe Mathieu-Daudé.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are needed by microvm too, so move them outside of PC-specific files.
With this patch, microvm.c need not include pc.h anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add it to microvm as well, it is a generic property of the x86
architecture.
Suggested-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the need to include i386/pc.h to get to the i8259 functions.
This is enough to remove the inclusion of hw/i386/pc.h from all non-x86
files.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The first machine property to fall is Xen's Intel integrated graphics
passthrough. The "-machine igd-passthru" option does not set anymore
a property on the machine object, but desugars to a GlobalProperty on
accelerator objects.
The setter is very simple, since the value ends up in a
global variable, so this patch also provides an example before the more
complicated cases that follow it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the "accel" property from MachineState, and instead desugar
"-machine accel=" to a list of "-accel" options.
This has a semantic change due to removing merge_lists from -accel.
For example:
- "-accel kvm -accel tcg" all but ignored "-accel kvm". This is a bugfix.
- "-accel kvm -accel thread=single" ignored "thread=single", since it
applied the option to KVM. Now it fails due to not specifying the
accelerator on "-accel thread=single".
- "-accel tcg -accel thread=single" chose single-threaded TCG, while now
it will fail due to not specifying the accelerator on "-accel
thread=single".
Also, "-machine accel" and "-accel" become incompatible.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's been deprecated since QEMU v3.1. We've explicitly asked in the
deprecation message that people should speak up on qemu-devel in case
they are still actively using the bluetooth part of QEMU, but nobody
ever replied that they are really still using it.
I've tried it on my own to use this bluetooth subsystem for one of my
guests, but I was also not able to get it running anymore: When I was
trying to pass-through a real bluetooth device, either the guest did
not see the device at all, or the guest crashed.
Even worse for the emulated device: When running
qemu-system-x86_64 -bt device:keyboard
QEMU crashes once you hit a key.
So it seems like the bluetooth stack is not only neglected, it is
completely bitrotten, as far as I can tell. The only attention that
this code got during the past years were some CVEs that have been
spotted there. So this code is a burden for the developers, without
any real benefit anymore. Time to remove it.
Note: hw/bt/Kconfig only gets cleared but not removed here yet.
Otherwise there is a problem with the *-softmmu/config-devices.mak.d
dependency files - they still contain a reference to this file which
gets evaluated first on some build hosts, before the file gets
properly recreated. To avoid breaking these builders, we still need
the file around for some time. It will get removed in a couple of
weeks instead.
Message-Id: <20191120091014.16883-4-thuth@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It isn't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623844102.360005.12070225703151669294.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XSCOM bus is implemented with a QOM interface, which is mostly
generic from a CPU type standpoint, except for the computation of
addresses on the Pervasive Connect Bus (PCB) network. This is handled
by the pnv_xscom_pcba() function with a switch statement based on
the chip_type class level attribute of the CPU chip.
This can be achieved using QOM. Also the address argument is masked with
PNV_XSCOM_SIZE - 1, which is for POWER8 only. Addresses may have different
sizes with other CPU types. Have each CPU chip type handle the appropriate
computation with a QOM xscom_pcba() method.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623843543.360005.13996472463887521794.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
They aren't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623842986.360005.1787401623906380181.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since pnv_dt_xscom() is called from chip specific dt_populate() hooks,
it shouldn't have to guess the chip type in order to populate the
"compatible" property. Just pass the compat string and its size as
arguments.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623842430.360005.9513965612524265862.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since pnv_dt_xscom() is called from chip specific dt_populate() hooks,
it shouldn't have to guess the chip type in order to populate the "reg"
property. Just pass the base address and address size as arguments.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623841868.360005.17577624823547136435.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_chip_core_realize() function configures the XSCOM MMIO subregion
for each core of a single chip. The base address of the subregion depends
on the CPU type. Its computation is currently open-code using the
pnv_chip_is_powerXX() helpers. This can be achieved with QOM. Introduce
a method for this in the base chip class and implement it in child classes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623841311.360005.4705705734873339545.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_pic_print_info() callback checks the type of the chip in order
to forward to the request appropriate interrupt controller. This can
be achieved with QOM. Introduce a method for this in the base chip class
and implement it in child classes.
This also prepares ground for the upcoming interrupt controller of POWER10
chips.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623840755.360005.5002022339473369934.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
They aren't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623840200.360005.1300941274565357363.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We add an extra node to advertise power management on some machines,
namely powernv9 and powernv10. This is achieved by using the
pnv_is_power9() and pnv_is_power10() helpers.
This can be achieved with QOM. Add a method to the base class for
powernv machines and have it implemented by machine types that
support power management instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623839642.360005.9243510140436689941.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_dt_create() function generates different contents for the
"compatible" property of the root node in the DT, depending on the
CPU type. This is open coded with multiple ifs using pnv_is_powerXX()
helpers.
It seems cleaner to achieve with QOM. Introduce a base class for the
powernv machine and a compat attribute that each child class can use
to provide the value for the "compatible" property.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623839085.360005.4046508784077843216.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in small fix Greg spotted after posting]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It isn't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623838530.360005.15470128760871845396.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Service Interface (PSI) model has a chip_type class level
attribute, which is used to generate the content of the "compatible" DT
property according to the CPU type.
Since the PSI model already has specialized classes for each supported
CPU type, it seems cleaner to achieve this with QOM. Provide the content
of the "compatible" property with a new class level attribute.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623837974.360005.14706607446188964477.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <157623837421.360005.412120366652768311.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC common area is mapped at a unique address on the system and
each OCC is assigned a segment to expose its sensor data :
-------------------------------------------------------------------------
| Start (Offset from | End | Size |Description |
| BAR2 base address) | | | |
-------------------------------------------------------------------------
| 0x00580000 | 0x005A57FF |150kB |OCC 0 Sensor Data Block|
| 0x005A5800 | 0x005CAFFF |150kB |OCC 1 Sensor Data Block|
| : | : | : | : |
| 0x00686800 | 0x006ABFFF |150kB |OCC 7 Sensor Data Block|
| 0x006AC000 | 0x006FFFFF |336kB |Reserved |
-------------------------------------------------------------------------
Maximum size is 1.5MB.
We could define a "OCC common area" memory region at the machine level
and sub regions for each OCC. But it adds some extra complexity to the
models. Fix the current layout with a simpler model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191211082912.2625-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PBA bridge unit (Power Bus Access) connects the OCC (On Chip
Controller) to the Power bus and System Memory. The PBA is used to
gather sensor data, for power management, for sleep states, for
initial boot, among other things.
The PBA logic provides a set of four registers PowerBus Access Base
Address Registers (PBABAR0..3) which map the OCC address space to the
PowerBus space. These registers are setup by the initial FW and define
the PowerBus Range of system memory that can be accessed by PBA.
The current modeling of the PBABAR registers is done under the common
XSCOM handlers. We introduce a specific XSCOM regions for these
registers and fix :
- BAR sizes and BAR masks
- The mapping of the OCC common area. It is common to all chips and
should be mapped once. We will address per-OCC area in the next
change.
- OCC common area is in BAR 3 on P8
Inspired by previous work of Balamuruhan S <bala24@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191211082912.2625-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PnvXScomInterface is an interface instance. It should never be
dereferenced. Drop the dummy type definition for extra safety,
which is the common practice with QOM interfaces.
While here also convert the bogus OBJECT_CHECK() to INTERFACE_CHECK().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157608025541.186670.1577861507610404326.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Utilisation of Resources Register (PURR) and Scaled
Processor Utilisation of Resources Register (SPURR) provide an estimate
of the resources used by the thread, present on POWER7 and later
processors.
Currently the [S]PURR registers simply count at the rate of the
timebase.
Preserve this behaviour but rework the implementation to store an offset
like the timebase rather than doing the calculation manually. Also allow
hypervisor write access to the register along with the currently
available read access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The virtual timebase register (VTB) is a 64-bit register which
increments at the same rate as the timebase register, present on POWER8
and later processors.
The register is able to be read/written by the hypervisor and read by
the supervisor. All other accesses are illegal.
Currently the VTB is just an alias for the timebase (TB) register.
Implement the VTB so that is can be read/written independent of the TB.
Make use of the existing method for accessing timebase facilities where
by the compensation is stored and used to compute the value on reads/is
updated on writes.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Same a POWER9, only the MMIO window changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER10 PSIHB controller is very similar to the one on POWER9. We
should probably introduce a common PnvPsiXive object.
The ESB page size should be changed to 64k when P10 support is ready.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is an empty shell with the XSCOM bus and cores. The chip controllers
will come later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU is reset, QEMU makes sure no interrupt is pending by clearing
CPUPPCstate::pending_interrupts in ppc_cpu_reset(). In the case of a
complete machine emulation, eg. a sPAPR machine, an external interrupt
request could still be pending in KVM though, eg. an IPI. It will be
eventually presented to the guest, which is supposed to acknowledge it at
the interrupt controller. If the interrupt controller is emulated in QEMU,
either XICS or XIVE, ppc_set_irq() won't deassert the external interrupt
pin in KVM since it isn't pending anymore for QEMU. When the vCPU re-enters
the guest, the interrupt request is still pending and the vCPU will try
again to acknowledge it. This causes an infinite loop and eventually hangs
the guest.
The code has been broken since the beginning. The issue wasn't hit before
because accel=kvm,kernel-irqchip=off is an awkward setup that never got
used until recently with the LC92x IBM systems (aka, Boston).
Add a ppc_irq_reset() function to do the necessary cleanup, ie. deassert
the IRQ pins of the CPU in QEMU and most importantly the external interrupt
pin for this vCPU in KVM.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157548861740.3650476.16879693165328764758.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_ovec_diff(ov, old, new) has somewhat complex semantics. ov is set
to those bits which are in new but not old, and it returns as a boolean
whether or not there are any bits in old but not new.
It turns out that both callers only care about the second, not the first.
This is basically equivalent to a bitmap subset operation, which is easier
to understand and implement. So replace spapr_ovec_diff() with
spapr_ovec_subset().
Cc: Mike Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cedric Le Goater <clg@fr.ibm.com>
spapr_h_cas_compose_response() handles the last piece of the PAPR feature
negotiation process invoked via the ibm,client-architecture-support OF
call. Its only caller is h_client_architecture_support() which handles
most of the rest of that process.
I believe it was placed in a separate file originally to handle some
fiddly dependencies between functions, but mostly it's just confusing
to have the CAS process split into two pieces like this. Now that
compose response is simplified (by just generating the whole device
tree anew), it's cleaner to just fold it into
h_client_architecture_support().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cedric Le Goater <clg@fr.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
This is useful to dump the saved contexts of the vCPUs : configuration
of the base END index of the vCPU and the Interrupt Pending Buffer
register, which is updated when an interrupt can not be presented.
When dumping the NVT table, we skip empty indirect pages which are not
necessarily allocated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-21-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When doing CAM line compares, fetch the block id from the interrupt
controller which can have set the PC_TCTXT_CHIPID field.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-20-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When PC_TCTXT_CHIPID_OVERRIDE is configured, the PC_TCTXT_CHIPID field
overrides the hardwired chip ID in the Powerbus operations and for CAM
compares. This is typically used in the one block-per-chip configuration
to associate a unique block id number to each IC of the system.
Simplify the model with a pnv_xive_block_id() helper and remove
'tctx_chipid' which becomes useless.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-19-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to resend missed interrupts when a vCPU context is
pushed on a HW thread.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-17-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is now unused.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-16-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the P9 Processor, the thread interrupt context registers of a CPU
can be accessed "directly" when by load/store from the CPU or
"indirectly" by the IC through an indirect TIMA page. This requires to
configure first the PC_TCTXT_INDIRx registers.
Today, we rely on the get_tctx() handler to deduce from the CPU PIR
the chip from which the TIMA access is being done. By handling the
TIMA memory ops under the interrupt controller model of each machine,
we can uniformize the TIMA direct and indirect ops under PowerNV. We
can also check that the CPUs have been enabled in the XIVE controller.
This prepares ground for the future versions of XIVE.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA region gives access to the thread interrupt context registers
of a CPU. It is mapped at the same address on all chips and can be
accessed by any CPU of the system. To identify the chip from which the
access is being done, the PowerBUS uses a 'chip' field in the
load/store messages. QEMU does not model these messages, instead, we
extract the chip id from the CPU PIR and do a lookup at the machine
level to fetch the targeted interrupt controller.
Introduce pnv_get_chip() and pnv_xive_tm_get_xive() helpers to clarify
this process in pnv_xive_get_tctx(). The latter will be removed in the
subsequent patches but the same principle will be kept.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE and XICS-on-XIVE KVM devices on POWER9 hosts can greatly reduce
their consumption of some scarce HW resources, namely Virtual Presenter
identifiers, if they know the maximum number of vCPUs that may run in the
VM.
Prepare ground for this by passing the value down to xics_kvm_connect()
and kvmppc_xive_connect(). This is purely mechanical, no functional
change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678301.67101.2717368060417156338.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA operations are performed on behalf of the XIVE IVPE sub-engine
(Presenter) on the thread interrupt context registers. The current
operations supported by the model are simple and do not require access
to the controller but more complex operations will need access to the
controller NVT table and to its configuration.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveFabric QOM interface acts as the PowerBUS interface between
the interrupt controller and the system and should be implemented by
the QEMU machine. On HW, the XIVE sub-engine is responsible for the
communication with the other chip is the Common Queue (CQ) bridge
unit.
This interface offers a 'match_nvt' handler to perform the CAM line
matching when looking for a XIVE Presenter with a dispatched NVT.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the TIMA of a CPU needs to be accessed from the indirect page,
the thread id of the target CPU is first stored in the PC_TCTXT_INDIR0
register. This thread id is relative to the chip and not to the system.
Introduce a helper routine to look for a CPU of a given PIR and fix
pnv_xive_get_indirect_tctx() to scan only the threads of the local
chip and not the whole machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
and use this helper to exclude CPUs which are not enabled in the XIVE
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Allocating a big void * array to store multiple objects isn't a
recommended practice for various reasons:
- no compile time type checking
- potential dangling pointers if a reference on an individual is
taken and the array is freed later on
- duplicate boiler plate everywhere the array is browsed through
Allocate an array of pointers and populate it instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the XIVE IVRE sub-engine (XiveRouter) looks for a Notification
Virtual Target (NVT) to notify, it broadcasts a message on the
PowerBUS to find an XIVE IVPE sub-engine (Presenter) with the NVT
dispatched on one of its HW threads, and then forwards the
notification if any response was received.
The current XIVE presenter model is sufficient for the pseries machine
because it has a single interrupt controller device, but the PowerNV
machine can have multiple chips each having its own interrupt
controller. In this case, the XIVE presenter model is too simple and
the CAM line matching should scan all chips of the system.
To start fixing this issue, we first extend the XIVE Router model with
a new XivePresenter QOM interface representing the XIVE IVPE
sub-engine. This interface exposes a 'match_nvt' handler which the
sPAPR and PowerNV XIVE Router models will need to implement to perform
the CAM line matching.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The BMC of the OpenPOWER systems monitors the machine state using
sensors, controls the power and controls the access to the PNOR flash
device containing the firmware image required to boot the host.
QEMU models the power cycle process, access to the sensors and access
to the PNOR device. But, for these features to be available, the QEMU
PowerNV machine needs two extras devices on the command line, an IPMI
BT device for communication and a BMC backend device:
-device ipmi-bmc-sim,id=bmc0 -device isa-ipmi-bt,bmc=bmc0,irq=10
The BMC properties are then defined accordingly in the device tree and
OPAL self adapts. If a BMC device and an IPMI BT device are not
available, OPAL does not try to communicate with the BMC in any
manner. This is not how real systems behave.
To be closer to the default behavior, create an IPMI BMC simulator
device and an IPMI BT device at machine initialization time. We loose
the ability to define an external BMC device but there are benefits:
- a better match with real systems,
- a better test coverage of the OPAL code,
- system powerdown and reset commands that work,
- a QEMU device tree compliant with the specifications (*).
(*) Still needs a MBOX device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191121162340.11049-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This activates HIOMAP support on the QEMU PowerNV machine. The PnvPnor
model is used to access the flash contents. The model simply maps the
contents at a fix offset and enables or disables the mapping.
HIOMAP Protocol description :
https://github.com/openbmc/hiomapd/blob/master/Documentation/protocol.md
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191028070027.22752-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each vCPU in the system is identified with an NVT identifier which is
pushed in the OS CAM line (QW1W2) of the HW thread interrupt context
register when the vCPU is dispatched on a HW thread. This identifier
is used by the presenter subengine to find a matching target to notify
of an event. It is also used to fetch the associate NVT structure
which may contain pending interrupts that need a resend.
Add a couple of helpers for the NVT ids. The NVT space is 19 bits
wide, giving a maximum of 512K per chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When an interrupt can not be presented to a vCPU, because it is not
running on any of the HW treads, the XIVE presenter updates the
Interrupt Pending Buffer register of the associated XIVE NVT
structure. This is only done if backlog is activated in the END but
this is generally the case.
The current code assumes that the fields of the NVT structure is
architected with the same layout of the thread interrupt context
registers. Fix this assumption and define an offset for the IPB
register backup value in the NVT.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On a POWERPC PowerNV system, the host firmware is stored in a PNOR
flash chip which contents is mapped on the LPC bus. This model adds a
simple dummy device to map the contents of a block device in the host
address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191021131215.3693-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* Add support for Cortex-M7 CPU
* exynos4210_gic: Suppress gcc9 format-truncation warnings
* aspeed: Various minor bug fixes and improvements
* aspeed: Add support for the tacoma-bmc board
* Honour HCR_EL32.TID1 and .TID2 trapping requirements
* Handle trapping to EL2 of AArch32 VMRS instructions
* Handle AArch32 CP15 trapping via HSTR_EL2
* Add support for missing Jazelle system registers
* arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on
* Add support for DC CVAP & DC CVADP instructions
* Fix assertion when SCR.NS is changed in Secure-SVC &c
* enable SHPC native hot plug in arm ACPI
-----BEGIN PGP SIGNATURE-----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=V+AK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20191216-1' into staging
target-arm queue:
* Add support for Cortex-M7 CPU
* exynos4210_gic: Suppress gcc9 format-truncation warnings
* aspeed: Various minor bug fixes and improvements
* aspeed: Add support for the tacoma-bmc board
* Honour HCR_EL32.TID1 and .TID2 trapping requirements
* Handle trapping to EL2 of AArch32 VMRS instructions
* Handle AArch32 CP15 trapping via HSTR_EL2
* Add support for missing Jazelle system registers
* arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on
* Add support for DC CVAP & DC CVADP instructions
* Fix assertion when SCR.NS is changed in Secure-SVC &c
* enable SHPC native hot plug in arm ACPI
# gpg: Signature made Mon 16 Dec 2019 11:08:07 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20191216-1: (34 commits)
target/arm: ensure we use current exception state after SCR update
hw/arm/virt: Simplify by moving the gic in the machine state
hw/arm/acpi: enable SHPC native hot plug
hw/arm/acpi: simplify AML bit and/or statement
hw/arm/sbsa-ref: Simplify by moving the gic in the machine state
target/arm: Add support for DC CVAP & DC CVADP ins
migration: ram: Switch to ram block writeback
Memory: Enable writeback for given memory region
tcg: cputlb: Add probe_read
arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on()
target/arm: Add support for missing Jazelle system registers
target/arm: Handle AArch32 CP15 trapping via HSTR_EL2
target/arm: Handle trapping to EL2 of AArch32 VMRS instructions
target/arm: Honor HCR_EL2.TID1 trapping requirements
target/arm: Honor HCR_EL2.TID2 trapping requirements
aspeed: Change the "nic" property definition
aspeed: Change the "scu" property definition
gpio: fix memory leak in aspeed_gpio_init()
aspeed: Add support for the tacoma-bmc board
aspeed: Remove AspeedBoardConfig array and use AspeedMachineClass
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the gic a field in the machine state, and instead of filling
an array of qemu_irq and passing it around, directly call
qdev_get_gpio_in() on the gic field.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191209090306.20433-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AspeedBoardConfig is a redundant way to define class attributes and it
complexifies the machine definition and initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Each CS has its own Read Timing Compensation Register on newer SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 control register sneakily changed the meaning of bit 4
without anyone noticing. It no longer controls the 1MHz vs APB clock
select, and instead always runs at 1MHz.
The AST2500 was always 1MHz too, but it retained bit 4, making it read
only. We can model both using the same fixed 1MHz calculation.
Fixes: 6b2b2a703c ("hw: wdt_aspeed: Add AST2600 support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, we link the DRAM memory region to the FMC model (for DMAs)
through a property alias at the SoC level. The I2C model will need a
similar region for DMA support, add a DRAM region property at the SoC
level for both model to use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRAM must be enabled before using the Buffer Pool mode or the DMA
mode. This is not required on other SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 5.0 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1; I'll leave changing this (if desired) to the respective
maintainers.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191112104811.30323-1-cohuck@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Virtio spec 1.1 (and earlier), 5.2.5.2 Driver Requirements: Device
Initialization:
"Devices SHOULD always offer VIRTIO_BLK_F_FLUSH, and MUST offer it if
they offer VIRTIO_BLK_F_CONFIG_WCE"
Currently F_CONFIG_WCE and F_WCE are not connected to each other.
Qemu will advertise F_CONFIG_WCE if config-wce argument is
set for virtio-blk device. And F_WCE is advertised only if
underlying block backend actually has it's caching enabled.
Fix this by advertising F_WCE if F_CONFIG_WCE is also advertised.
To preserve backwards compatibility with newer machine types make this
behaviour governed by "x-enable-wce-if-config-wce" virtio-blk-device
property and introduce hw_compat_4_2 with new property being off by
default for all machine types <= 4.2 (but don't introduce 4.3
machine type itself yet).
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1572978137-189218-1-git-send-email-wrfsh@yandex-team.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The property doesn't make much sense for a vhost-user device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191116112016.14872-1-marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add the CRP as unimplemented thus avoiding bus errors when
guests access these registers.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191115154734.26449-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds an optional function pointer, "sym_cb", to
riscv_load_kernel() which provides the possibility to access the symbol
table during kernel loading.
The pointer is ignored, if supplied with Image or uImage file.
The Spike board requires the access to locate the HTIF symbols.
Fixes: 0ac24d56c5 ("hw/riscv: Split out the boot functions")
Buglink: https://bugs.launchpad.net/qemu/+bug/1835827
Signed-off-by: Siwei Zhuang <siwei.zhuang@data61.csiro.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Attempting to migrate a VM using the microvm machine class results in the source
QEMU aborting with the following message/backtrace:
target/i386/machine.c:955:tsc_khz_needed: Object 0x555556608fa0 is not an
instance of type generic-pc-machine
abort()
object_class_dynamic_cast_assert()
vmstate_save_state_v()
vmstate_save_state()
vmstate_save()
qemu_savevm_state_complete_precopy()
migration_thread()
migration_thread()
migration_thread()
qemu_thread_start()
start_thread()
clone()
The access to the machine class returned by MACHINE_GET_CLASS() in
tsc_khz_needed() is crashing as it is trying to dereference a different
type of machine class object (TYPE_PC_MACHINE) to that of this microVM.
This can be resolved by extending the changes in the following commit
f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
and moving the save_tsc_khz field in PCMachineClass to X86MachineClass.
Fixes: f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <1574075605-25215-1-git-send-email-liam.merwick@oracle.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SpaprInterruptControllerClass and PnvChipClass have an intc_create() method
that calls the appropriate routine, ie. icp_create() or xive_tctx_create(),
to establish the link between the VCPU and the presenter component of the
interrupt controller during realize.
There aren't any symmetrical call to be called when the VCPU gets unrealized
though. It is assumed that object_unparent() is the only thing to do.
This is questionable because the parenting logic around the CPU and
presenter objects is really an implementation detail of the interrupt
controller. It shouldn't be open-coded in the machine code.
Fix this by adding an intc_destroy() method that undoes what was done in
intc_create(). Also NULLify the presenter pointers to avoid having
stale pointers around. This will allow to reliably check if a vCPU has
a valid presenter.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192724208.3146912.7254684777515287626.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
The boot.c code usually puts the CPU into NS mode directly when it is
booting a kernel. Since fc1120a7f5 this has included a
requirement to set NSACR to give NS state access to the FPU; we fixed
that for the usual code path in ece628fcf6. However, it is also
possible for a board model to request an alternative mode of booting,
where its 'board_setup' code hook runs in Secure state and is
responsible for doing the S->NS transition after it has done whatever
work it must do in Secure state. In this situation the board_setup
code now also needs to update NSACR.
This affects all boards which set info->secure_board_setup, which is
currently the 'raspi' and 'highbank' families. They both use the
common arm_write_secure_board_setup_dummy_smc().
Set the NSACR CP11 and CP10 bits in the code written by that
function, to allow FPU access in Non-Secure state when using dummy
SMC setup routine. Otherwise an AArch32 kernel booted on the
highbank or raspi boards will UNDEF as soon as it tries to use the
FPU.
Update the comment describing secure_board_setup to note the new
requirements on users of it.
This fixes a kernel panic when booting raspbian on raspi2.
Successfully tested with:
2017-01-11-raspbian-jessie-lite.img
2018-11-13-raspbian-stretch-lite.img
2019-07-10-raspbian-buster-lite.img
Fixes: fc1120a7f5
Signed-off-by: Clement Deschamps <clement.deschamps@greensocs.com>
Tested-by: Laurent Bonnans <laurent.bonnans@here.com>
Message-id: 20191104151137.81931-1-clement.deschamps@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: updated comment to boot.h to note new requirement on
users of secure_board_setup; edited/rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All targets have now migrated away from the old unassigned_access
hook to the new do_transaction_failed hook. This means we can remove
the core-code infrastructure for that hook and the code that calls it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191108173732.11816-1-peter.maydell@linaro.org
Now all the users of ptimers have converted to the transaction-based
API, we can remove ptimer_init_with_bh() and all the code paths
that are used only by bottom-half based ptimers, and tidy up the
documentation comments to consider the transaction-based API the
only possibility.
The code changes result from:
* s->bh no longer exists
* s->callback is now always non-NULL
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191025142411.17085-1-peter.maydell@linaro.org
'the' has a tendency to double up; squash them back down.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191104185202.102504-1-dgilbert@redhat.com>
[lv: removed disas/libvixl/vixl/invalset.h change]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Host notifiers are used in several cases:
1. Traditional ioeventfd where virtqueue notifications are handled in
the main loop thread.
2. IOThreads (aio_handle_output) where virtqueue notifications are
handled in an IOThread AioContext.
3. vhost where virtqueue notifications are handled by kernel vhost or
a vhost-user device backend.
Most virtqueue notifications from the guest use the ioeventfd mechanism,
but there are corner cases where QEMU code calls virtio_queue_notify().
This currently honors the host notifier for the IOThreads
aio_handle_output case, but not for the vhost case. The result is that
vhost does not receive virtqueue notifications from QEMU when
virtio_queue_notify() is called.
This patch extends virtio_queue_notify() to set the host notifier
whenever it is enabled instead of calling the vq->(aio_)handle_output()
function directly. We track the host notifier state for each virtqueue
separately since some devices may use it only for certain virtqueues.
This fixes the vhost case although it does add a trip through the
eventfd for the traditional ioeventfd case. I don't think it's worth
adding a fast path for the traditional ioeventfd case because calling
virtio_queue_notify() is rare when ioeventfd is enabled.
Reported-by: Felipe Franciosi <felipe@nutanix.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191105140946.165584-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PIIX3 is not tied to the i440FX and can even be used without it.
Move its creation to the machine code (pc_piix.c).
We have now removed the last trace of southbridge code in the i440FX
northbridge.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Move all the PIIX3 functions to a new file: hw/isa/piix3.c.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The hw/pci-host/piix.c contains a mix of PIIX3 and i440FX chipsets
functions. To be able to split it, we need to export some
declarations first.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The IRQ Route Control registers definitions belong to the PIIX
chipset. We were only defining the 'A' register. Define the other
B, C and D registers, and use them.
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The RCR_IOPORT register belongs to the PIIX chipset.
Move the definition to "piix.h", and prepend the PIIX prefix.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Now that we properly refactored the piix4_create() function, let's
move it to hw/isa/piix4.c where it belongs, so it can be reused
on other places.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Remove mc146818rtc instanciated in malta board, to not have it twice.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-13-hpoussin@reactos.org>
[PMD: rebased, set RTC base_year to 2000]
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Other piix4 parts are already named piix4-ide and piix4-usb-uhci.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-15-hpoussin@reactos.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Esteban Bosse <estebanbosse@gmail.com>
[PMD: rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This function isn't used anymore.
This reverts commit 22ec3283ef.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Esteban Bosse <estebanbosse@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add ISA irqs as piix4 gpio in, and CPU interrupt request as piix4 gpio out.
Remove i8259 instanciated in malta board, to not have it twice.
We can also remove the now unused piix4_init() function.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-8-hpoussin@reactos.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
[PMD: rebased, updated includes, use ISA_NUM_IRQS in for loop]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We will need to add LCHS removal logic to scsi-hd's unrealize() in the
next commit.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Add logical geometry variables to BlockConf.
A user can now supply "lcyls", "lheads" & "lsecs" for any HD device
that supports CHS ("cyls", "heads", "secs").
These devices include:
* ide-hd
* scsi-hd
* virtio-blk-pci
In future commits we will use the provided LCHS and pass it to the BIOS
through fw_cfg to be supplied using INT13 routines.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Fixing tabbing in block related macros.
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl23BZMACgkQ+9DbCVqe
KkRPegf/QHygZ4ER2jOaWEookxiOEcik+dzQKVGNqLNXeMLvo5fGjGVpFoFxSgfv
ZvCAL4xbW44zsYlVfh59tfn4Tu9qK7s7/qM3WXpHsmuvEuhoWef0Lt2jSe+D46Rs
KeG/aX+rHLUR8rr9eCgE+1/MQmxPUj3VUonkUpNkk2ebBbSNoLSOudB4DD9Vcyl7
Pya1kPvA6W9bwI20ZSWihE7flg13o62Pp+LgAFLrsfxXOxOMkPrU8Pp+B0Dvr+hL
5Oh0clZLhiRi75x+KVGZ90TVsoftdjYoOWGMOudS/+NNmqKT1NTLm0K1WJYyRMQ1
V0ne4/OcGNq7x8gcOx/xs09ADu5/VA==
=UXR/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tcg-plugins-281019-4' into staging
TCG Plugins initial implementation
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
# gpg: Signature made Mon 28 Oct 2019 15:13:23 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-plugins-281019-4: (57 commits)
travis.yml: enable linux-gcc-debug-tcg cache
MAINTAINERS: add me for the TCG plugins code
scripts/checkpatch.pl: don't complain about (foo, /* empty */)
.travis.yml: add --enable-plugins tests
include/exec: wrap cpu_ldst.h in CONFIG_TCG
accel/stubs: reduce headers from tcg-stub
tests/plugin: add hotpages to analyse memory access patterns
tests/plugin: add instruction execution breakdown
tests/plugin: add a hotblocks plugin
tests/tcg: enable plugin testing
tests/tcg: drop test-i386-fprem from TESTS when not SLOW
tests/tcg: move "virtual" tests to EXTRA_TESTS
tests/tcg: set QEMU_OPTS for all cris runs
tests/tcg/Makefile.target: fix path to config-host.mak
tests/plugin: add sample plugins
linux-user: support -plugin option
vl: support -plugin option
plugin: add qemu_plugin_outs helper
plugin: add qemu_plugin_insn_disas helper
plugin: expand the plugin_init function to include an info block
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support to handle failover device pairs of a virtio-net
device and a (vfio-)pci device, where the virtio-net acts as the standby
device and the (vfio-)pci device as the primary.
The general idea is that we have a pair of devices, a (vfio-)pci and a
emulated (virtio-net) device. Before migration the vfio device is
unplugged and data flows to the emulated device, on the target side
another (vfio-)pci device is plugged in to take over the data-path. In the
guest the net_failover module will pair net devices with the same MAC
address.
To achieve this we need:
1. Provide a callback function for the should_be_hidden DeviceListener.
It is called when the primary device is plugged in. Evaluate the QOpt
passed in to check if it is the matching primary device. It returns
if the device should be hidden or not.
When it should be hidden it stores the device options in the VirtioNet
struct and the device is added once the VIRTIO_NET_F_STANDBY feature is
negotiated during virtio feature negotiation.
If the virtio-net devices are not realized at the time the (vfio-)pci
devices are realized, we need to connect the devices later. This way
we make sure primary and standby devices can be specified in any
order.
2. Register a callback for migration status notifier. When called it
will unplug its primary device before the migration happens.
3. Register a callback for the migration code that checks if a device
needs to be unplugged from the guest.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-11-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In "b06424de62 migration: Disable hotplug/unplug during migration" we
added a check to disable unplug for all devices until we have figured
out what works. For failover primary devices qdev_unplug() is called
from the migration handler, i.e. during migration.
This patch adds a flag to DeviceState which is set to false for all
devices and makes an exception for PCI devices that are also
primary devices in a failover pair.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-8-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only the guest unplug request was triggered. This is needed for
the failover feature. In case of a failed migration we need to
plug the device back to the guest.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-4-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a failover_pair_id property to PCIDev which is
used to link the primary device in a failover pair (the PCI dev) to
a standby (a virtio-net-pci) device.
It only supports ethernet devices. Also currently it only supports
PCIe devices. The requirement for PCIe is because it doesn't support
other hotplug controllers at the moment. The failover functionality can
be added to other hotplug controllers like ACPI, SHCP,... later on.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-3-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds support for hiding a device to the qbus and qdev APIs. The
first user of this will be the virtio-net failover feature but the API
introduced with this patch could be used to implement other features as
well, for example hiding pci devices when a pci bus is powered off.
qdev_device_add() is modified to check for a failover_pair_id
argument in the option string. A DeviceListener callback
should_be_hidden() is added. It can be used by a standby device to
inform qdev that this device should not be added now. The standby device
handler can store the device options to plug the device in at a later
point in time.
One reason for hiding the device is that we don't want to expose both
devices to the guest kernel until the respective virtio feature bit
VIRTIO_NET_F_STANDBY was negotiated and we know that the devices will be
handled correctly by the guest.
More information on the kernel feature this is using:
https://www.kernel.org/doc/html/latest/networking/net_failover.html
An example where the primary device is a vfio-pci device and the standby
device is a virtio-net device:
A device is hidden when it has an "failover_pair_id" option, e.g.
-device virtio-net-pci,...,failover=on,...
-device vfio-pci,...,failover_pair_id=net1,...
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-2-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJdt6UAAAoJEO8Ells5jWIRdaAH/3+dufJuFijZY44VYbob92ud
lZR1dYah1fBL1bq0F2siFUb+/wgF1IXHJl9tuUJe8Kp0+hnsXji2s4Iuq5lNQoJj
wwMGziL1TPkhxwgy4jObIC+/bqZVrzAO4Cd+PARrSGAAbAqjxLPizOaf72/t4kdn
C2n87ZlR5k0EOPmUY6Y2DtHtrJ20usSS6EThGhdW7iPSzfQSGiOdRzfZrSiEV2XT
cuKbSzQxk7pbPcz4jIgLzaoA7FIXwm99dBosUkjPszNNFbO4+OPDNdUBanYuqmn/
0ZPe/9YZpEMV64ps/Ab7lx7YB04wZ+A9Etln2JULhBWXg/oyri9gsqgOc6bfCXg=
=uE5S
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Tue 29 Oct 2019 02:33:36 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
COLO-compare: Fix incorrect `if` logic
virtio-net: prevent offloads reset on migration
virtio: new post_load hook
net: add tulip (dec21143) driver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently offloads disabled by guest via the VIRTIO_NET_CTRL_GUEST_OFFLOADS_SET
command are not preserved on VM migration.
Instead all offloads reported by guest features (via VIRTIO_PCI_GUEST_FEATURES)
get enabled.
What happens is: first the VirtIONet::curr_guest_offloads gets restored and offloads
are getting set correctly:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=0, tso6=0, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_post_load_device (opaque=0x555557701ca0, version_id=11) at hw/net/virtio-net.c:2334
#3 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577c80 <vmstate_virtio_net_device>, opaque=0x555557701ca0, version_id=11)
at migration/vmstate.c:168
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2197
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
However later on the features are getting restored, and offloads get reset to
everything supported by features:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=1, tso6=1, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_set_features (vdev=0x555557701ca0, features=5104441767) at hw/net/virtio-net.c:773
#3 virtio_set_features_nocheck (vdev=0x555557701ca0, val=5104441767) at hw/virtio/virtio.c:2052
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2220
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
Fix this by preserving the state in saved_guest_offloads field and
pushing out offload initialization to the new post load hook.
Cc: qemu-stable@nongnu.org
Signed-off-by: Mikhail Sennikovsky <mikhail.sennikovskii@cloud.ionos.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Post load hook in virtio vmsd is called early while device is processed,
and when VirtIODevice core isn't fully initialized. Most device
specific code isn't ready to deal with a device in such state, and
behaves weirdly.
Add a new post_load hook in a device class instead. Devices should use
this unless they specifically want to verify the migration stream as
it's processed, e.g. for bounds checking.
Cc: qemu-stable@nongnu.org
Suggested-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mikhail Sennikovsky <mikhail.sennikovskii@cloud.ionos.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds the basic functionality to emulate a Tulip NIC.
Implemented are:
- RX and TX functionality
- Perfect Frame Filtering
- Big/Little Endian descriptor support
- 93C46 EEPROM support
- LXT970 PHY
Not implemented, mostly because i had no OS using these functions:
- Imperfect frame filtering
- General Purpose Timer
- Transmit automatic polling
- Boot ROM support
- SIA interface
- Big/Little Endian data buffer conversion
Successfully tested with the following Operating Systems:
- MSDOS with Microsoft Network Client 3.0 and DEC ODI drivers
- HPPA Linux
- Windows XP
- HP-UX
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191022155413.4619-1-svens@stackframe.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch set contains a handful of small fixes for RISC-V targets that
I'd like to target for the 4.2 soft freeze. They include:
* A fix to allow the debugger to access the state of all privilege
modes, as opposed to just the currently executing one.
* A pair of cleanups to implement cpu_do_transaction_failed.
* Fixes to the device tree.
* The addition of various memory regions to make the sifive_u machine
more closely match the HiFive Unleashed board.
* Fixes to our GDB interface to allow CSRs to be accessed.
* A fix to a memory leak pointed out by coverity.
* A fix that prevents PMP checks from firing incorrectly.
This passes "make chcek" and boots Open Embedded for me.
-----BEGIN PGP SIGNATURE-----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=e4jZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.2-sf2' into staging
RISC-V Patches for the 4.2 Soft Freeze, Part 2
This patch set contains a handful of small fixes for RISC-V targets that
I'd like to target for the 4.2 soft freeze. They include:
* A fix to allow the debugger to access the state of all privilege
modes, as opposed to just the currently executing one.
* A pair of cleanups to implement cpu_do_transaction_failed.
* Fixes to the device tree.
* The addition of various memory regions to make the sifive_u machine
more closely match the HiFive Unleashed board.
* Fixes to our GDB interface to allow CSRs to be accessed.
* A fix to a memory leak pointed out by coverity.
* A fix that prevents PMP checks from firing incorrectly.
This passes "make chcek" and boots Open Embedded for me.
# gpg: Signature made Mon 28 Oct 2019 15:47:52 GMT
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.2-sf2:
target/riscv: PMP violation due to wrong size parameter
riscv/boot: Fix possible memory leak
target/riscv: Make the priv register writable by GDB
target/riscv: Expose "priv" register for GDB for reads
target/riscv: Tell gdbstub the correct number of CSRs
riscv/virt: Jump to pflash if specified
riscv/virt: Add the PFlash CFI01 device
riscv/virt: Manually define the machine
riscv/sifive_u: Add the start-in-flash property
riscv/sifive_u: Manually define the machine
riscv/sifive_u: Add QSPI memory region
riscv/sifive_u: Add L2-LIM cache memory
linux-user/riscv: Propagate fault address
riscv: sifive_u: Add ethernet0 to the aliases node
riscv: hw: Drop "clock-frequency" property of cpu nodes
RISC-V: Implement cpu_do_transaction_failed
RISC-V: Handle bus errors in the page table walker
riscv: Skip checking CSR privilege level in debugger mode
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SWIM (Sander-Wozniak Integrated Machine) is the floppy controller of
the 680x0 Macintosh.
This patch introduces only the basic support: it allows to switch from
IWM (Integrated WOZ Machine) mode to the SWIM mode and makes the linux
driver happy.
It cannot read any floppy image.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-10-laurent@vivier.eu>
This patch adds support for a graphic framebuffer device.
This device can be added as a sysbus device or as a NuBus device.
It is accessed as a framebuffer but the color palette can be set.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-9-laurent@vivier.eu>
This patch adds basic support for the NuBus bus. This is used by 680x0
Macintosh.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-8-laurent@vivier.eu>
VIA needs to be able to poll the ADB interface and to read/write data
from/to the bus.
This patch adds functions allowing that.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-7-laurent@vivier.eu>
Inside the 680x0 Macintosh, VIA (Versatile Interface Adapter) is used
to interface the keyboard, Mouse, and real-time clock. It also provides
control line for the floppy disk driver, video interface, sound circuitry
and serial interface.
This implementation is based on the MOS6522 object.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-6-laurent@vivier.eu>
There is no DMA in Quadra 800, so the CPU reads/writes the data from the
PDMA register (offset 0x100, ESP_PDMA in hw/m68k/q800.c) and copies them
to/from the memory.
There is a nice assembly loop in the kernel to do that, see
linux/drivers/scsi/mac_esp.c:MAC_ESP_PDMA_LOOP().
The start of the transfer is triggered by the DREQ interrupt (see linux
mac_esp_send_pdma_cmd()), the CPU polls on the IRQ flag to start the
transfer after a SCSI command has been sent (in Quadra 800 it goes
through the VIA2, the via2-irq line and the vIFR register)
The Macintosh hardware includes hardware handshaking to prevent the CPU
from reading invalid data or writing data faster than the peripheral
device can accept it.
This is the "blind mode", and from the doc:
"Approximate maximum SCSI transfer rates within a blocks are 1.4 MB per
second for blind transfers in the Macintosh II"
Some references can be found in:
Apple Macintosh Family Hardware Reference, ISBN 0-201-19255-1
Guide to the Macintosh Family Hardware, ISBN-0-201-52405-8
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-4-laurent@vivier.eu>
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: moved directory and merged various fixes]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: moved inside start/end_exclusive fns + cleanup]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add the CFI01 PFlash to the RISC-V virt board. This is the same PFlash
from the ARM Virt board and the implementation is based on the ARM Virt
board. This allows users to specify flash files from the command line.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Instead of using the DEFINE_MACHINE() macro to define the machine let's
do it manually. This allows us to use the machine object to create
RISCVVirtState. This is required to add children and aliases to the
machine.
This patch is no functional change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a property that when set to true QEMU will jump from the ROM code to
the start of flash memory instead of DRAM which is the default
behaviour.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Instead of using the DEFINE_MACHINE() macro to define the machine let's
do it manually. This allows us to specify machine properties.
This patch is no functional change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The HiFive Unleashed uses is25wp256 SPI NOR flash. There is currently no
model of this in QEMU, so to allow boot firmware developers to use QEMU
to target the Unleashed let's add a chunk of memory to represent the QSPI0
memory mapped flash. This can be targeted using QEMU's -device loader
command line option.
In the future we can look at adding a model for the is25wp256 flash.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
On reset only a single L2 cache way is enabled, the others are exposed
as memory that can be used by early boot firmware. This L2 region is
generally disabled using the WayEnable register at a later stage in the
boot process. To allow firmware to target QEMU and the HiFive Unleashed
let's add the L2 LIM (LooselyIntegrated Memory).
Ideally we would want to adjust the size of this chunk of memory as the
L2 Cache Controller WayEnable register is incremented. Unfortunately I
don't see a nice way to handle reducing or blocking out the L2 LIM while
still allowing it be re returned to all enabled from a reset.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The "clock-frequency" property of cpu nodes isn't required. Drop it.
This is to keep in sync with Linux kernel commit below:
https://patchwork.kernel.org/patch/11133031/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEkb62CjDbPohX0Rgp9AfbAGHVz0AFAl2224ESHG1yZWl0ekBy
ZWRoYXQuY29tAAoJEPQH2wBh1c9AeXMH/RXKEX4BZYMRKCe41P18tJC9Bl2x0T20
YeOsZVvpARlr7o/36BF2kGFF4MnL0OQ+9ELuyROX865rk/VL2rWqnHDE5oQM889a
dFwMs+0zvNbig3iLNcw0H5OkE2mrdM+a1EUdn/lBe/39Z8dPqPxRGqIYHq38Ugdu
emwSy1nWen7o0f71HRJfyVtI3KcrzXx71FrA/FY2yL/eHz+zRYGZj2SpAdFPkXP/
lgaz+m0tWhnSW1QzEOXB0Gh69ULt/DczCinYmv5qUY1noW5TPPtiDNCQTts5O4ba
oJsR3AJv5/l9m65JTmiyQSqnQfPcstrQ5FqOcSnP637cfqUFyWsvdks=
=L7v1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-2019-10-28' into staging
Block patches for softfreeze:
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
# gpg: Signature made Mon 28 Oct 2019 12:13:53 GMT
# gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40
# gpg: issuer "mreitz@redhat.com"
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2019-10-28: (69 commits)
qemu-iotests: restrict 264 to qcow2 only
Revert "qemu-img: Check post-truncation size"
block: Pass truncate exact=true where reasonable
block: Let format drivers pass @exact
block: Evaluate @exact in protocol drivers
block: Add @exact parameter to bdrv_co_truncate()
block: Do not truncate file node when formatting
block/cor: Drop cor_co_truncate()
block: Handle filter truncation like native impl.
iotests: Test qcow2's snapshot table handling
iotests: Add peek_file* functions
qcow2: Fix v3 snapshot table entry compliancy
qcow2: Repair snapshot table with too many entries
qcow2: Fix overly long snapshot tables
qcow2: Keep track of the snapshot table length
qcow2: Fix broken snapshot table entries
qcow2: Add qcow2_check_fix_snapshot_table()
qcow2: Separate qcow2_check_read_snapshot_table()
qcow2: Write v3-compliant snapshot list on upgrade
qcow2: Put qcow2_upgrade() into its own function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
libqos update with support for virtio 1.
Packed ring support for virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdsuDvAAoJECgfDbjSjVRpIP8H/3rHSvZ5+MQGCFLI5GU8m3za
JSOaBSmtcj9KwrpibBfptSCJZNrG8EUVHyo+Z+pvGohXqDB8h9RyBfb6vID8jqzC
5wIzlNBP27F668MUBt2t7xSwK0PWO1QOpEKk6S4SJMpl51ea8ePlTH0jnLVfkaAN
hFKU1wqwc2gMyF9rDjOZ6I+OO1iQbMcrsazFrCXECXCkxDcJM0ey7MheKxVntTjt
0sxFHM2I1A+vXtAzlLo6rS3I9vJ0ATfLfOlZLqrq5uSAL5FKrqsbmGh4sAsFTQAA
eerR6zDz3X+YqfQaVgVk2wixPHQz2w8Rv68j6SiGrdZ29/JT6nVWHT8cGtPsX4c=
=iJuG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio: features, tests
libqos update with support for virtio 1.
Packed ring support for virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 25 Oct 2019 12:47:59 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (25 commits)
virtio: drop unused virtio_device_stop_ioeventfd() function
libqos: add VIRTIO PCI 1.0 support
libqos: extract Legacy virtio-pci.c code
libqos: make the virtio-pci BAR index configurable
libqos: expose common virtqueue setup/cleanup functions
libqos: add MSI-X callbacks to QVirtioPCIDevice
libqos: pass full QVirtQueue to set_queue_address()
libqos: add iteration support to qpci_find_capability()
libqos: access VIRTIO 1.0 vring in little-endian
libqos: implement VIRTIO 1.0 FEATURES_OK step
libqos: enforce Device Initialization order
libqos: add missing virtio-9p feature negotiation
tests/virtio-blk-test: set up virtqueue after feature negotiation
virtio-scsi-test: add missing feature negotiation
libqos: extend feature bits to 64-bit
libqos: read QVIRTIO_MMIO_VERSION register
tests/virtio-blk-test: read config space after feature negotiation
virtio: add property to enable packed virtqueue
vhost_net: enable packed ring support
virtio: event suppression support for packed ring
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
endof() is a useful macro, we can make use of it outside of virtio.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Move it out of pc.c since it is strictly tied to TCG. This is
almost exclusively code movement, the next patch will implement
IGNNE.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As we are going to add more core-specific fields, add a 'cpu'
structure and move the ARMCPU field there as 'core'.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191019234715.25750-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the recently added SYS_timer.
Now U-Boot does not hang anymore polling a free running counter
stuck at 0.
This timer is also used by the Linux kernel thermal subsystem.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191019234715.25750-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Map the thermal sensor in the BCM2835 block.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191019234715.25750-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We will soon implement the SYS_timer. This timer is used by Linux
in the thermal subsystem, so once available, the subsystem will be
enabled and poll the temperature sensors. We need to provide the
minimum required to keep Linux booting.
Add a dummy thermal sensor returning ~25°C based on:
https://github.com/raspberrypi/linux/blob/rpi-5.3.y/drivers/thermal/broadcom/bcm2835_thermal.c
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191019234715.25750-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio_device_stop_ioeventfd() has not been used since commit
310837de6c ("virtio: introduce
grab/release_ioeventfd to fix vhost") in 2016.
Nowadays ioeventfd is stopped implicitly by the virtio transport when
lifecycle events such as the VM pausing or device unplug occur.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191021150343.30742-1-stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191025083527.30803-9-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements basic support for the packed virtqueue. Compare
the split virtqueue which has three rings, packed virtqueue only have
one which is supposed to have better cache utilization and more
hardware friendly.
Please refer virtio specification for more information.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20191025083527.30803-6-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The system <stdint.h> include is already provided by "osdep.h"
(the scripts/clean-includes file clean such headers).
Commit 64552b6be4 suggests we don't need to include "hw/irq.h":
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-15-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Only 2 source files require the "mc146818rtc_regs.h" header.
Instead of having it processed 12 times, by all objects
using "mc146818rtc.h", include it directly where used.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-13-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move RTC devices under the hw/rtc/ subdirectory.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-12-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The M48T59 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MC146818 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Use copyright statement from 80cabfad16 for "hw/rtc/mc146818rtc.h".
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PL031 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20191023130455.1347-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Devices/boards wanting to use the MC146818 RTC don't need
the knowledge its internal registers. Move the "mc146818rtc_regs.h"
inclusion to mc146818rtc.c where it is required.
We can not move this file from include/hw/timer/ to hw/timer/ for
local inclusion because the ACPI FADT table use the RTC_CENTURY
register address.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191018133547.10936-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The ISA default number for the RTC devices is not related to its
registers neither. Move this definition to "hw/timer/mc146818rtc.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191018133547.10936-3-philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We are now able to embed a timer in another object.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-4-hpoussin@reactos.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191018133547.10936-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The i8259 creation code is common to all PC machines, extract the
common code.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191018135910.24286-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GSI creation code is common to all PC machines, extract the
common code.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191018135910.24286-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a Virtual Processor is scheduled to run on a HW thread, the
hypervisor pushes its identifier in the OS CAM line. When running with
kernel_irqchip=off, QEMU needs to emulate the same behavior.
Set the OS CAM line when the interrupt presenter of the sPAPR core is
reset. This will also cover the case of hot-plugged CPUs.
This change also has the benefit to remove the use of CPU_FOREACH()
which can be unsafe.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the sPAPR machine and PowerNV machine, the interrupt presenters are
created by a machine handler at the core level and are reset
independently. This is not consistent and it raises issues when it
comes to handle hot-plugged CPUs. In that case, the presenters are not
reset. This is less of an issue in XICS, although a zero MFFR could
be a concern, but in XIVE, the OS CAM line is not set and this breaks
the presenting algorithm. The current code has workarounds which need
a global cleanup.
Extend the sPAPR IRQ backend and the PowerNV Chip class with a new
cpu_intc_reset() handler called by the CPU reset handler and remove
the XiveTCTX reset handler which is now redundant.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191022163812.330-6-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to reset the interrupt presenter from the CPU reset
handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-5-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the benefit of peripheral device allocation, the number of available
irqs really wants to be the same on a given machine type version,
regardless of what irq backends we are using. That's the case now, but
only because we make sure the different SpaprIrq instances have the same
value except for the special legacy one.
Since this really only depends on machine type version, move the value to
SpaprMachineClass instead of SpaprIrq. This also puts the code to set it
to the lower value on old machine types right next to setting
legacy_irq_allocation, which needs to go hand in hand.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The nr_msis value we use here has to line up with whether we're using
legacy or modern irq allocation. Therefore it's safer to derive it based
on legacy_irq_allocation rather than having SpaprIrq contain a canned
value.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The remaining logic in the post_load hook really belongs to the interrupt
controller backends, and just needs to be called on the active controller
(after the active controller is set to the right thing based on the
incoming migration in the generic spapr_irq_post_load() logic).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It turns out that all the logic in the SpaprIrq::reset hooks (and some in
the SpaprIrq::post_load hooks) isn't really related to resetting the irq
backend (that's handled by the backends' own reset routines). Rather its
about getting the backend ready to be the active interrupt controller or
stopping being the active interrupt controller - reset (and post_load) is
just the only time that changes at present.
To make this flow clearer, move the logic into the explicit backend
activate and deactivate hooks.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This hook is a bit odd. The only caller is spapr_irq_init_kvm(), but
it explicitly takes an SpaprIrq *, so it's never really called through the
current SpaprIrq. Essentially this is just a way of passing through a
function pointer so that spapr_irq_init_kvm() can handle some
configuration and error handling logic without duplicating it between the
xics and xive reset paths.
So, make it just take that function pointer. Because of earlier reworks
to the KVM connect/disconnect code in the xics and xive backends we can
also eliminate some wrapper functions and streamline error handling a bit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Both XICS and XIVE have routines to connect and disconnect KVM with
similar but not identical signatures. This adjusts them to match
exactly, which will be useful for further cleanups later.
While we're there, we add an explicit return value to the connect path
to streamline error reporting in the callers. We remove error
reporting the disconnect path. In the XICS case this wasn't used at
all. In the XIVE case the only error case was if the KVM device was
set up, but KVM didn't have the capability to do so which is pretty
obviously impossible.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly through
that, rather than dispatching via SpaprIrq with the dual version having
to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
spapr now has the mechanism of constructing both XICS and XIVE instances of
the SpaprInterruptController interface. However, only one of the interrupt
controllers will actually be active at any given time, depending on feature
negotiation with the guest. This is handled in the current code via
spapr_irq_current() which checks the OV5 vector from feature negotiation to
determine the current backend.
Determining the active controller at the point we need it like this
can be pretty confusing, because it makes it very non obvious at what
points the active controller can change. This can make it difficult
to reason about the code and where a change of active controller could
appear in sequence with other events.
Make this mechanism more explicit by adding an 'active_intc' pointer
and an explicit spapr_irq_update_active_intc() function to update it
from the CAS state. We also add hooks on the intc backend which will
get called when it is activated or deactivated.
For now we just introduce the switch and hooks, later patches will
actually start using them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
These methods, like cpu_intc_create, really belong to the interrupt
controller, but need to be called on all possible intcs.
Like cpu_intc_create, therefore, make them methods on the intc and
always call it for all existing intcs.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method essentially represents code which belongs to the interrupt
controller, but needs to be called on all possible intcs, rather than
just the currently active one. The "dual" version therefore calls
into the xics and xive versions confusingly.
Handle this more directly, by making it instead a method on the intc
backend, and always calling it on every backend that exists.
While we're there, streamline the error reporting a bit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The SpaprIrq structure is used to represent ths spapr machine's irq
backend. Except that it kind of conflates two concepts: one is the
backend proper - a specific interrupt controller that we might or
might not be using, the other is the irq configuration which covers
the layout of irq space and which interrupt controllers are allowed.
This leads to some pretty confusing code paths for the "dual"
configuration where its hooks redirect to other SpaprIrq structures
depending on the currently active irq controller.
To clean this up, we start by introducing a new
SpaprInterruptController QOM interface to represent strictly an
interrupt controller backend, not counting anything configuration
related. We implement this interface in the XICs and XIVE interrupt
controllers, and in future we'll move relevant methods from SpaprIrq
into it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Support for setting VSMT is available in KVM since linux-4.13. Most distros
that support KVM on POWER already have it. It thus seem reasonable enough
to have the default machine to set VSMT to smp_threads.
This brings contiguous VCPU ids and thus brings their upper bound down to
the machine's max_cpus. This is especially useful for XIVE KVM devices,
which may thus allocate only one VP descriptor per VCPU.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157010411885.246126.12610015369068227139.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The trigger data is used for both triggers of a HW source interrupts,
PHB, PSI, and triggers for rerouting interrupts between interrupt
controllers.
When an interrupt is rerouted, the trigger data follows an "END
trigger" format. In that case, the remote IC needs EAS containing an
END index to perform a lookup of an END.
An END trigger, bit0 of word0 set to '1', is defined as :
|0123|4567|0123|4567|0123|4567|0123|4567|
W0 E=1 |1P--|BLOC| END IDX |
W1 E=1 |M | END DATA |
An EAS is defined as :
|0123|4567|0123|4567|0123|4567|0123|4567|
W0 |V---|BLOC| END IDX |
W1 |M | END DATA |
The END trigger adds an extra 'PQ' bit, bit1 of word0 set to '1',
signaling that the PQ bits have been checked. That bit is unused in
the initial EAS definition.
When a HW device performs the trigger, the trigger data follows an
"EAS trigger" format because the trigger data in that case contains an
EAS index which the IC needs to look for.
An EAS trigger, bit0 of word0 set to '0', is defined as :
|0123|4567|0123|4567|0123|4567|0123|4567|
W0 E=0 |0P--|---- ---- ---- ---- ---- ---- ----|
W1 E=0 |BLOC| EAS INDEX |
There is also a 'PQ' bit, bit1 of word0 to '1', signaling that the
PQ bits have been checked.
Introduce these new trigger bits and rename the XIVE_SRCNO macros in
XIVE_EAS to reflect better the nature of the data.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191007084102.29776-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The SDRAM is incorrectly created in the OMAP310 SoC.
Move its creation in the board code, this will later allow the
board to have the QOM ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-6-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDRAM is incorrectly created in the OMAP2420 SoC.
Move its creation in the board code, this will later allow the
board to have the QOM ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
microvm is a machine type inspired by Firecracker and constructed
after its machine model.
It's a minimalist machine type without PCI nor ACPI support, designed
for short-lived guests. microvm also establishes a baseline for
benchmarking and optimizing both QEMU and guest operating systems,
since it is optimized for both boot time and footprint.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This allows to alter the contents of an already added item.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
As a last step into splitting PCMachineState and deriving
X86MachineState from it, make the functions previously extracted from
pc.c to x86.c independent from PCMachineState, using X86MachineState
instead.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Split up PCMachineState and PCMachineClass and derive X86MachineState
and X86MachineClass from them. This allows sharing code with non-PC
x86 machine types.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Move x86 functions that will be shared between PC and non-PC machine
types to x86.c, along with their helpers.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
The following functions are named *pc* but are not PC-machine specific
but generic to the X86 architecture, rename them:
load_linux -> x86_load_linux
pc_new_cpu -> x86_new_cpu
pc_cpus_init -> x86_cpus_init
pc_cpu_index_to_props -> x86_cpu_index_to_props
pc_get_default_cpu_node_id -> x86_get_default_cpu_node_id
pc_possible_cpu_arch_ids -> x86_possible_cpu_arch_ids
old_pc_system_rom_init -> x86_system_rom_init
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Put QOM and main struct definition in a separate header file, so it
can be accessed from other components.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
ARM ACPI memory hotplug support +
tests for new arm/virt ACPI tables.
Virtio fs support (no migration).
A vhost-user reconnect bugfix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdpjPbAAoJECgfDbjSjVRpQqUH/2xyT++y8K17mCI1IILLZd3d
eOqElEHz78qlEfR2euv63YksZoeHpMO5HiAdwOGGF8CjcaCT4Hl+pPDffTYVXtt+
VZ88vSSXL49wpMcpvRGR5Isy0eXJzWilTBMu2eu8phN9tX82dlu08Oi4XGAosrBJ
uZg61DyiGDnSOpoofHhjvXJEaiL0pzkTjf8qAoW3TaVcB9NQKnunMEIDD646JS5z
AAj4+XBJfUG9cp7/MG+djjVmJDdUpjL5e5uWNWakbgUVqSbHog78RIrBoD6SH7pt
/6hHHoSM9VX1wWgdTdVdNAQAZVnWs31w4v31d8UfaT15KJEoG47U0gDgmLzXDyo=
=+xdg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, acpi: features, fixes, tests
ARM ACPI memory hotplug support +
tests for new arm/virt ACPI tables.
Virtio fs support (no migration).
A vhost-user reconnect bugfix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2019 22:02:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio: add vhost-user-fs-pci device
virtio: add vhost-user-fs base device
virtio: Add virtio_fs linux headers
tests/acpi: add expected tables for arm/virt
tests: document how to update acpi tables
tests: Add bios tests to arm/virt
tests: allow empty expected files
tests/acpi: add empty files
tests: Update ACPI tables list for upcoming arm/virt tests
docs/specs: Add ACPI GED documentation
hw/arm: Use GED for system_powerdown event
hw/arm: Factor out powerdown notifier from GPIO
hw/arm/virt-acpi-build: Add PC-DIMM in SRAT
hw/arm/virt: Enable device memory cold/hot plug with ACPI boot
hw/arm/virt: Add memory hotplug framework
hw/acpi: Add ACPI Generic Event Device Support
hw/acpi: Do not create memory hotplug method when handler is not defined
hw/acpi: Make ACPI IO address space configurable
vhost-user: save features if the char dev is closed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add MachineClass::auto_enable_numa field. When it is true, a NUMA node
is expected to be created implicitly.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190905083238.1799-1-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Base addresses and sizes taken from the "BCM2835 ARM Peripherals"
datasheet from February 06 2012:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190926173428.10713-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The UART1 is part of the AUX peripheral,
the PCM_CLOCK (yet unimplemented) is part of the CPRMAN.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190926173428.10713-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-24-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 SoC has an extra controller to set the PHY registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-23-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To support the ast2600's four MACs allow SoCs to specify the number
they have, and create that many.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-22-clg@kaod.org
[clg: - included a check on sc->macs_num when realizing the macs
- included interrupt definitions for the AST2600 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initial definitions for a simple machine using an AST2600 SoC (Cortex
CPU).
The Cortex CPU and its interrupt controller are too complex to handle
in the common Aspeed SoC framework. We introduce a new Aspeed SoC
class with instance_init and realize handlers to handle the differences
with the AST2400 and the AST2500 SoCs. This will add extra work to
keep in sync both models with future extensions but it makes the code
clearer.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-19-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for the AST2600.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-18-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the AST2400 and AST2500 SoCs have one IRQ shared
by all I2C busses. The AST2600 SoC I2C controller has one IRQ per bus
and 16 busses.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for register differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-16-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AST2600 will use a different encoding for the addresses defined in the
Segment Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 has four watchdogs, and they each have a 0x40 of registers.
When running as part of an ast2600 system we must check a different
offset for the system reset control register in the SCU.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-12-clg@kaod.org
[clg: - reworked model integration into new object class ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It cleanups the current models for the Aspeed AST2400 and AST2500 SoCs
and prepares ground for future SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-11-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 SDMC controller is slightly different from its predecessor
(DRAM training). Max memory is now 2G on the AST2600.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-10-clg@kaod.org
[clg: - improved commit log
- reworked model integration into new object class ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use class handlers and class constants to differentiate the
characteristics of the memory controller and remove the 'silicon_rev'
property.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 timer replaces control register 2 with a interrupt status
register. It is set by hardware when an IRQ occurs and cleared by
software.
Modify the vmstate version to take into account the new fields.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
On the AST2600, it is not configurable via 0x38 (control register 3)
as it is on the AST2500.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
This models the behaviour expected by the AST2500 while maintaining
the same behaviour for the AST2400.
The vmstate version is not increased yet because the structure is
modified again in the following patches.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The most important changes will be on the register range 0x34 - 0x3C
memops. Introduce class read/write operations to handle the
differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SCU controller on the AST2600 SoC has extra registers. Increase
the number of regs of the model and introduce a new field in the class
to customize the MemoryRegion operations depending on the SoC model.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-4-clg@kaod.org
[clg: - improved commit log
- changed vmstate version
- reworked model integration into new object class
- included AST2600_HPLL_PARAM value ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SOCs have two SD/MMC controllers. Add a device that
encapsulates both of these controllers and models the Aspeed-specific
registers and behavior.
Tested by reading from mmcblk0 in Linux:
qemu-system-arm -machine romulus-bmc -nographic \
-drive file=flash-romulus,format=raw,if=mtd \
-device sd-card,drive=sd0 -drive file=_tmp/kernel,format=raw,if=sd,id=sd0
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-3-clg@kaod.org
[clg: - changed the controller MMIO window size to 0x1000
- moved the MMIO mapping of the SDHCI slots at the SoC level
- merged code to add SD drives on the SD buses at the machine level ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the mss-timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-20-peter.maydell@linaro.org
Provide the new transaction-based API. If a ptimer is created
using ptimer_init() rather than ptimer_init_with_bh(), then
instead of providing a QEMUBH, it provides a pointer to the
callback function directly, and has opted into the transaction
API. All calls to functions which modify ptimer state:
- ptimer_set_period()
- ptimer_set_freq()
- ptimer_set_limit()
- ptimer_set_count()
- ptimer_run()
- ptimer_stop()
must be between matched calls to ptimer_transaction_begin()
and ptimer_transaction_commit(). When ptimer_transaction_commit()
is called it will evaluate the state of the timer after all the
changes in the transaction, and call the callback if necessary.
In the old API the individual update functions generally would
call ptimer_trigger() immediately, which would schedule the QEMUBH.
In the new API the update functions will instead defer the
"set s->next_event and call ptimer_reload()" work to
ptimer_transaction_commit().
Because ptimer_trigger() can now immediately call into the
device code which may then call other ptimer functions that
update ptimer_state fields, we must be more careful in
ptimer_reload() not to cache fields from ptimer_state across
the ptimer_trigger() call. (This was harmless with the QEMUBH
mechanism as the BH would not be invoked until much later.)
We use assertions to check that:
* the functions modifying ptimer state are not called outside
a transaction block
* ptimer_transaction_begin() and _commit() calls are paired
* the transaction API is not used with a QEMUBH ptimer
There is some slight repetition of code:
* most of the set functions have similar looking "if s->bh
call ptimer_reload, otherwise set s->need_reload" code
* ptimer_init() and ptimer_init_with_bh() have similar code
We deliberately don't try to avoid this repetition, because
it will all be deleted when the QEMUBH version of the API
is removed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-3-peter.maydell@linaro.org
Currently the ptimer design uses a QEMU bottom-half as its
mechanism for calling back into the device model using the
ptimer when the timer has expired. Unfortunately this design
is fatally flawed, because it means that there is a lag
between the ptimer updating its own state and the device
callback function updating device state, and guest accesses
to device registers between the two can return inconsistent
device state.
We want to replace the bottom-half design with one where
the guest device's callback is called either immediately
(when the ptimer triggers by timeout) or when the device
model code closes a transaction-begin/end section (when the
ptimer triggers because the device model changed the
ptimer's count value or other state). As the first step,
rename ptimer_init() to ptimer_init_with_bh(), to free up
the ptimer_init() name for the new API. We can then convert
all the ptimer users away from ptimer_init_with_bh() before
removing it entirely.
(Commit created with
git grep -l ptimer_init | xargs sed -i -e 's/ptimer_init/ptimer_init_with_bh/'
and three overlong lines folded by hand.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-2-peter.maydell@linaro.org
Here's the next batch of ppc and spapr patches. Includes:
* Fist part of a large cleanup to irq infrastructure
* Recreate the full FDT at CAS time, instead of making a difficult
to follow set of updates. This will help us move towards
eliminating CAS reboots altogether
* No longer provide RTAS blob to SLOF - SLOF can include it just as
well itself, since guests will generally need to relocate it with
a call to instantiate-rtas
* A number of DFP fixes and cleanups from Mark Cave-Ayland
* Assorted bugfixes
* Several new small devices for powernv
-----BEGIN PGP SIGNATURE-----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=PXXe
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191004' into staging
ppc patch queue 2019-10-04
Here's the next batch of ppc and spapr patches. Includes:
* Fist part of a large cleanup to irq infrastructure
* Recreate the full FDT at CAS time, instead of making a difficult
to follow set of updates. This will help us move towards
eliminating CAS reboots altogether
* No longer provide RTAS blob to SLOF - SLOF can include it just as
well itself, since guests will generally need to relocate it with
a call to instantiate-rtas
* A number of DFP fixes and cleanups from Mark Cave-Ayland
* Assorted bugfixes
* Several new small devices for powernv
# gpg: Signature made Fri 04 Oct 2019 10:35:57 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191004: (53 commits)
ppc/pnv: Remove the XICSFabric Interface from the POWER9 machine
spapr: Eliminate SpaprIrq::init hook
spapr: Add return value to spapr_irq_check()
spapr: Use less cryptic representation of which irq backends are supported
xive: Improve irq claim/free path
spapr, xics, xive: Better use of assert()s on irq claim/free paths
spapr: Handle freeing of multiple irqs in frontend only
spapr: Remove unhelpful tracepoints from spapr_irq_free_xics()
spapr: Eliminate SpaprIrq:get_nodename method
spapr: Simplify spapr_qirq() handling
spapr: Fix indexing of XICS irqs
spapr: Eliminate nr_irqs parameter to SpaprIrq::init
spapr: Clarify and fix handling of nr_irqs
spapr: Replace spapr_vio_qirq() helper with spapr_vio_irq_pulse() helper
spapr: Fold spapr_phb_lsi_qirq() into its single caller
xics: Create sPAPR specific ICS subtype
xics: Merge TYPE_ICS_BASE and TYPE_ICS_SIMPLE classes
xics: Eliminate reset hook
xics: Rename misleading ics_simple_*() functions
xics: Eliminate 'reject', 'resend' and 'eoi' class hooks
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virtio-fs virtio device provides shared file system access using
the FUSE protocol carried over virtio.
The actual file server is implemented in an external vhost-user-fs device
backend process.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190930105135.27244-3-dgilbert@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For machines 4.2 or higher with ACPI boot use GED for system_powerdown
event instead of GPIO. Guest boot with DT still uses GPIO.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-9-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is in preparation of using GED device for
system_powerdown event. Make the powerdown notifier
registration independent of create_gpio() fn.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-8-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This initializes the GED device with base memory and irq, configures
ged memory hotplug event and builds the corresponding aml code. With
this, both hot and cold plug of device memory is enabled now for Guest
with ACPI boot. Memory cold plug support with Guest DT boot is not yet
supported.
As DSDT table gets changed by this, update bios-tables-test-allowed-diff.h
to avoid "make check" failure.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Message-Id: <20190918130633.4872-6-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The ACPI Generic Event Device (GED) is a hardware-reduced specific
device[ACPI v6.1 Section 5.6.9] that handles all platform events,
including the hotplug ones. This patch generates the AML code that
defines GEDs.
Platforms need to specify their own GED Event bitmap to describe
what kind of events they want to support through GED. Also this
uses a a single interrupt for the GED device, relying on IO
memory region to communicate the type of device affected by the
interrupt. This way, we can support up to 32 events with a unique
interrupt.
This supports only memory hotplug for now.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20190918130633.4872-4-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
This is in preparation for adding support for ARM64 platforms
where it doesn't use port mapped IO for ACPI IO space. We are
making changes so that MMIO region can be accommodated
and board can pass the base address into the aml build function.
Also move few MEMORY_* definitions to header so that other memory
hotplug event signalling mechanisms (eg. Generic Event Device on
HW-reduced acpi platforms) can use the same from their respective
event handler code.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-2-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The container error integer field is currently used to store
the first error potentially encountered during any
vfio_listener_region_add() call. However this fails to propagate
detailed error messages up to the vfio_connect_container caller.
Instead of using an integer, let's use an Error handle.
Messages are slightly reworded to accomodate the propagation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This method is used to set up the interrupt backends for the current
configuration. However, this means some confusing redirection between
the "dual" mode init and the init hooks for xics only and xive only modes.
Since we now have simple flags indicating whether XICS and/or XIVE are
supported, it's easier to just open code each initialization directly in
spapr_irq_init(). This will also make some future cleanups simpler.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
SpaprIrq::ov5 stores the value for a particular byte in PAPR option vector
5 which indicates whether XICS, XIVE or both interrupt controllers are
available. As usual for PAPR, the encoding is kind of overly complicated
and confusing (though to be fair there are some backwards compat things it
has to handle).
But to make our internal code clearer, have SpaprIrq encode more directly
which backends are available as two booleans, and derive the OV5 value from
that at the point we need it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
spapr_xive_irq_claim() returns a bool to indicate if it succeeded.
But most of the callers and one callee use int return values and/or an
Error * with more information instead. In any case, ints are a more
common idiom for success/failure states than bools (one never knows
what sense they'll be in).
So instead change to an int return value to indicate presence of error
+ an Error * to describe the details through that call chain.
It also didn't actually check if the irq was already claimed, which is
one of the primary purposes of the claim path, so do that.
spapr_xive_irq_free() also returned a bool... which no callers checked
and was always true, so just drop it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
spapr_irq_free() can be used to free multiple irqs at once. That's useful
for its callers, but there's no need to make the individual backend hooks
handle this. We can loop across the irqs in spapr_irq_free() itself and
have the hooks just do one at time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method is used to determine the name of the irq backend's node in the
device tree, so that we can find its phandle (after SLOF may have modified
it from the phandle we initially gave it).
But, in the two cases the only difference between the node name is the
presence of a unit address. Searching for a node name without considering
unit address is standard practice for the device tree, and
fdt_subnode_offset() will do exactly that, making this method unecessary.
While we're there, remove the XICS_NODENAME define. The name
"interrupt-controller" is required by PAPR (and IEEE1275), and a bunch of
places assume it already.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently spapr_qirq(), whic is used to find the qemu_irq for an spapr
global irq number, redirects through the SpaprIrq::qirq method. But
the array of qemu_irqs is allocated in the PAPR layer, not the
backends, and so the method implementations all return the same thing,
just differing in the preliminary checks they make.
So, we can remove the method, and just implement spapr_qirq() directly,
including all the relevant checks in one place. We change all those
checks into assert()s as well, since a failure here indicates an error in
the calling code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The only reason this parameter was needed was to work around the
inconsistent meaning of nr_irqs between xics and xive. Now that we've
fixed that, we can consistently use the number directly in the SpaprIrq
configuration.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Both the XICS and XIVE interrupt backends have a "nr-irqs" property, but
it means slightly different things. For XICS (or, strictly, the ICS) it
indicates the number of "real" external IRQs. Those start at XICS_IRQ_BASE
(0x1000) and don't include the special IPI vector. For XIVE, however, it
includes the whole IRQ space, including XIVE's many IPI vectors.
The spapr code currently doesn't handle this sensibly, with the
nr_irqs value in SpaprIrq having different meanings depending on the
backend. We fix this by renaming nr_irqs to nr_xirqs and making it
always indicate just the number of external irqs, adjusting the value
we pass to XIVE accordingly. We also move to using common constants
in most of the irq configurations, to make it clearer that the IRQ
space looks the same to the guest (and emulated devices), even if the
backend is different.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Every caller of spapr_vio_qirq() immediately calls qemu_irq_pulse() with
the result, so we might as well just fold that into the helper.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
No point having a two-line helper that's used exactly once, and not likely
to be used anywhere else in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We create a subtype of TYPE_ICS specifically for sPAPR. For now all this
does is move the setup of the PAPR specific hcalls and RTAS calls to
the realize() function for this, rather than requiring the PAPR code to
explicitly call xics_spapr_init(). In future it will have some more
function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
TYPE_ICS_SIMPLE is the only subtype of TYPE_ICS_BASE that's ever
instantiated. The existence of different classes is mostly a hang
over from when we (misguidedly) had separate subtypes for the KVM and
non-KVM version of the device.
There could be some call for an abstract base type for ICS variants
that use a different representation of their state (PowerNV PHB3 might
want this). The current split isn't really in the right place for
that though. If we need this in future, we can re-implement it more
in line with what we actually need.
So, collapse the two classes together into just TYPE_ICS.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently TYPE_XICS_BASE and TYPE_XICS_SIMPLE have their own reset methods,
using the standard technique for having the subtype call the supertype's
methods before doing its own thing.
But TYPE_XICS_SIMPLE is the only subtype of TYPE_XICS_BASE ever
instantiated, so there's no point having the split here. Merge them
together into just an ics_reset() function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
There are a number of ics_simple_*() functions that aren't actually
specific to TYPE_XICS_SIMPLE at all, and are equally valid on
TYPE_XICS_BASE. Rename them to ics_*() accordingly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently ics_reject(), ics_resend() and ics_eoi() indirect through
class methods. But there's only one implementation of each method,
the one in TYPE_ICS_SIMPLE. TYPE_ICS_BASE has no implementation, but
it's never instantiated, and has no other subtypes.
So clean up by eliminating the method and just having ics_reject(),
ics_resend() and ics_eoi() contain the logic directly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Interface instances should never be directly dereferenced. So, the common
practice is to make them incomplete types to make sure no-one does that.
XICSFrabric, however, had a dummy type which is less safe.
We were also using OBJECT_CHECK() where we should have been using
INTERFACE_CHECK().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
SLOF implements one itself so let's remove it from QEMU. It is one less
image and simpler setup as the RTAS blob never stays in its initial place
anyway as the guest OS always decides where to put it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Certain old guest versions don't understand the radix MMU introduced with
POWER ISA 3.0, but incorrectly select it if presented with the option at
CAS time. We workaround this in qemu by explicitly excluding the radix
(and other ISA 3.0 linked) options if the guest doesn't explicitly note
support for ISA 3.0.
This is handled by the 'cas_legacy_guest_workaround' flag, which is pretty
vague. Rename it to 'cas_pre_isa3_guest' to be clearer about what it's for.
In addition, we unnecessarily call spapr_populate_pa_features() with
different options when initially constructing the device tree and when
adjusting it at CAS time. At the initial construct time cas_pre_isa3_guest
is already false, so we can still use the flag, rather than explicitly
overriding it to be false at the callsite.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
It will help us to discard interrupt numbers which have not been
claimed in the next patch.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190911133937.2716-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
add PnvHomer device model to emulate homer memory access
for pstate table, occ-sensors, slw, occ static and dynamic
values for Power8 and Power9 chips.
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Message-Id: <20190912093056.4516-4-bala24@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
emulate occ common area region with occ sram device model which
occ and skiboot uses it to communicate regarding sensors, slw
and HWMON in PowerNV emulated host.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Message-Id: <20190912093056.4516-3-bala24@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
During PowerNV boot skiboot populates the device tree by
retrieving base address of homer/occ common area from
PBA BARs and prd ipoll mask by accessing xscom read/write
accesses.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Balamuruhan S <bala24@linux.ibm.com>
Message-Id: <20190912093056.4516-2-bala24@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
With the merge of notdirty handling into store_helper,
the last user of cpu->mem_io_vaddr was removed.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleaning up offline XenDevice objects directly in
xen_device_backend_changed() is dangerous as xen_device_unrealize() will
modify the watch list that is being walked. Even the QLIST_FOREACH_SAFE()
used in notifier_list_notify() is insufficient as *two* notifiers (for
the frontend and backend watches) are removed, thus potentially rendering
the 'next' pointer unsafe.
The solution is to use the XenBus backend_watch handler to do the clean-up
instead, as it is invoked whilst walking a separate watch list.
This patch therefore adds a new 'inactive_devices' list to XenBus, to which
offline devices are added by xen_device_backend_changed(). The XenBus
backend_watch registration is also changed to not only invoke
xen_bus_enumerate() but also a new xen_bus_cleanup() function, which will
walk 'inactive_devices' and perform the necessary actions.
For safety an extra 'online' check is also added to xen_bus_type_enumerate()
to make sure that no attempt is made to create a new XenDevice object for a
backend that is offline.
NOTE: This patch also includes some cosmetic changes:
- substitute the local variable name 'backend_state'
in xen_bus_type_enumerate() with 'state', since there
is no ambiguity with any other state in that context.
- change xen_device_state_is_active() to
xen_device_frontend_is_active() (and pass a XenDevice directly)
since the state tests contained therein only apply to a frontend.
- use 'state' rather then 'xendev->backend_state' in
xen_device_backend_changed() to shorten the code.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190913082159.31338-4-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch uses the XenWatchList abstraction to add a separate watch list
for each device. This is more scalable than walking a single notifier
list for all watches and is also necessary to implement a bug-fix in a
subsequent patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Message-Id: <20190913082159.31338-3-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Xenstore watch call-backs are already abstracted away from XenBus using
the XenWatch data structure but the associated NotifierList manipulation
and file handle registration is still open coded in various xen_bus_...()
functions.
This patch creates a new XenWatchList data structure to allow these
interactions to be abstracted away from XenBus as well. This is in
preparation for a subsequent patch which will introduce separate watch lists
for XenBus and XenDevice objects.
NOTE: This patch also introduces a new notifier_list_empty() helper function
for the purposes of adding an assertion that a XenWatchList is not
freed whilst its associated NotifierList is still occupied.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Message-Id: <20190913082159.31338-2-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is so I2C devices can be found in the ACPI namespace. Currently
that's only IPMI, but devices can be easily added now.
Adding the devices required some PCI information, and the bus itself
to be added to the PCMachineState structure.
Note that this only works on Q35, the ACPI for PIIX4 is not capable
of handling an SMBus device.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Pass in the CRS so that it can be set to the SMBus for IPMI later.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This will be required for getting IPMI SSIF (SMBus interface) into
the ACPI tables.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Pretty straightforward, just hook the current KCS and BT code into
the PCI system with the proper configuration.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: M: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
PCI device I/O must be >= 8 bytes in length or they don't work.
Allow the size to be passed in, the default size of 2 or 3
won't work.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Get ready for PCI and other BT interfaces.
No functional changes, just split the code into generic BT code
and ISA-specific BT code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Get ready for PCI and other KCS interfaces.
No functional changes, just split the code into the generic KCS code
and the ISA-specific code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This is for IPMI, which will behave differently if the UUID is
not set.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Fam Zheng <famz@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
This contains quite a few patches that I'd like to target for 4.2.
They're mostly emulation fixes for the sifive_u board, which now much
more closely matches the hardware and can therefor run the same fireware
as what gets loaded onto the board. Additional user-visible
improvements include:
* support for loading initrd files from the command line into Linux, via
/chosen/linux,initrd-{start,end} device tree nodes.
* The conversion of LOG_TRACE to trace events.
* The addition of clock DT nodes for our uart and ethernet.
This also includes some preliminary work for the H extension patches,
but does not include the H extension patches as I haven't had time to
review them yet.
This passes my OE boot test on 32-bit and 64-bit virt machines, as well
as a 64-bit upstream Linux boot on the sifive_u machine. It has been
fixed to actually pass "make check" this time.
Changes since v2 (never made it to the list):
* Sets the sifive_u machine default core count to 2 instead of 5.
Changes since v1 <20190910190513.21160-1-palmer@sifive.com>:
* Sets the sifive_u machine default core count to 5 instead of 1, as
it's impossible to have a single core sifive_u machine.
-----BEGIN PGP SIGNATURE-----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=yDSj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.2-sf1-v3' into staging
RISC-V Patches for the 4.2 Soft Freeze, Part 1, v3
This contains quite a few patches that I'd like to target for 4.2.
They're mostly emulation fixes for the sifive_u board, which now much
more closely matches the hardware and can therefor run the same fireware
as what gets loaded onto the board. Additional user-visible
improvements include:
* support for loading initrd files from the command line into Linux, via
/chosen/linux,initrd-{start,end} device tree nodes.
* The conversion of LOG_TRACE to trace events.
* The addition of clock DT nodes for our uart and ethernet.
This also includes some preliminary work for the H extension patches,
but does not include the H extension patches as I haven't had time to
review them yet.
This passes my OE boot test on 32-bit and 64-bit virt machines, as well
as a 64-bit upstream Linux boot on the sifive_u machine. It has been
fixed to actually pass "make check" this time.
Changes since v2 (never made it to the list):
* Sets the sifive_u machine default core count to 2 instead of 5.
Changes since v1 <20190910190513.21160-1-palmer@sifive.com>:
* Sets the sifive_u machine default core count to 5 instead of 1, as
it's impossible to have a single core sifive_u machine.
# gpg: Signature made Tue 17 Sep 2019 16:43:30 BST
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.2-sf1-v3: (48 commits)
gdbstub: riscv: fix the fflags registers
target/riscv: Use TB_FLAGS_MSTATUS_FS for floating point
target/riscv: Fix mstatus dirty mask
target/riscv: Use both register name and ABI name
riscv: sifive_u: Update model and compatible strings in device tree
riscv: sifive_u: Remove handcrafted clock nodes for UART and ethernet
riscv: sifive_u: Fix broken GEM support
riscv: sifive_u: Instantiate OTP memory with a serial number
riscv: sifive: Implement a model for SiFive FU540 OTP
riscv: roms: Update default bios for sifive_u machine
riscv: sifive_u: Change UART node name in device tree
riscv: sifive_u: Update UART base addresses and IRQs
riscv: sifive_u: Reference PRCI clocks in UART and ethernet nodes
riscv: sifive_u: Add PRCI block to the SoC
riscv: sifive_u: Generate hfclk and rtcclk nodes
riscv: sifive: Implement PRCI model for FU540
riscv: sifive_u: Update PLIC hart topology configuration string
riscv: sifive_u: Update hart configuration to reflect the real FU540 SoC
riscv: sifive_u: Set the minimum number of cpus to 2
riscv: hart: Add a "hartid-base" property to RISC-V hart array
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the past we did not have a model for PRCI, hence two handcrafted
clock nodes ("/soc/ethclk" and "/soc/uartclk") were created for the
purpose of supplying hard-coded clock frequencies. But now since we
have added the PRCI support in QEMU, we don't need them any more.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the GEM support in sifive_u machine is seriously broken.
The GEM block register base was set to a weird number (0x100900FC),
which for no way could work with the cadence_gem model in QEMU.
Not like other GEM variants, the FU540-specific GEM has a management
block to control 10/100/1000Mbps link speed changes, that is mapped
to 0x100a0000. We can simply map it into MMIO space without special
handling using create_unimplemented_device().
Update the GEM node compatible string to use the official name used
by the upstream Linux kernel, and add the management block reg base
& size to the <reg> property encoding.
Tested with upstream U-Boot and Linux kernel MACB drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds an OTP memory with a given serial number to the sifive_u
machine. With such support, the upstream U-Boot for sifive_fu540
boots out of the box on the sifive_u machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This implements a simple model for SiFive FU540 OTP (One-Time
Programmable) Memory interface, primarily for reading out the
stored serial number from the first 1 KiB of the 16 KiB OTP
memory reserved by SiFive for internal use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This updates the UART base address and IRQs to match the hardware.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jonathan Behrens <fintelia@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Now that we have added a PRCI node, update existing UART and ethernet
nodes to reference PRCI as their clock sources, to keep in sync with
the Linux kernel device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add PRCI mmio base address and size mappings to sifive_u machine,
and generate the corresponding device tree node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
To keep in sync with Linux kernel device tree, generate hfclk and
rtcclk nodes in the device tree, to be referenced by PRCI node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a simple PRCI model for FU540 (sifive_u). It has different
register layout from the existing PRCI model for FE310 (sifive_e).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The FU540-C000 includes a 64-bit E51 RISC-V core and four 64-bit U54
RISC-V cores. Currently the sifive_u machine only populates 4 U54
cores. Update the max cpu number to 5 to reflect the real hardware,
by creating 2 CPU clusters as containers for RISC-V hart arrays to
populate heterogeneous harts.
The cpu nodes in the generated DTS have been updated as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It is not useful if we only have one management CPU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
[Palmer: Set default CPUs to 2]
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present each hart's hartid in a RISC-V hart array is assigned
the same value of its index in the hart array. But for a system
that has multiple hart arrays, this is not the case any more.
Add a new "hartid-base" property so that hartid number can be
assigned based on the property value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Group SiFive E and U cpu type defines into one header file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently the PRCI register block size is set to 0x8000, but in fact
0x1000 is enough, which is also what the manual says.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Current SiFive PRCI model only works with sifive_e machine, as it
only emulates registers or PRCI block in the FE310 SoC.
Rename the file name to make it clear that it is for sifive_e.
This also prefix "sifive_e"/"SIFIVE_E" for all macros, variables
and functions.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a reset opcode for sifive_test device to trigger a system
reset for testing purpose.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a helper routine for finding firmware. It is currently
used only for "-bios default" case.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce this new per-machine hook to give any machine class a chance
to do a sanity check on the to-be-hotplugged device as a sanity test.
This will be used for x86 to try to detect some illegal configuration
of devices, e.g., possible conflictions between vfio-pci and x86
vIOMMU.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190916080718.3299-3-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch fixes a possible integer overflow when we calculate
the total size of ELF segments loaded.
Reported-by: Coverity (CID 1405299)
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190910124828.39794-1-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The APB frequency can be calculated directly when needed from the
HPLL_PARAM and CLK_SEL register values. This removes useless state in
the model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-11-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
and use a class AspeedSCUClass to define each SoC characteristics.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-10-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Emulate read errors in the DMA Checksum Register for high frequencies
and optimistic settings of the Read Timing Compensation Register. This
will help in tuning the SPI timing calibration algorithm. Errors are
only injected when the property "inject_failure" is set to true as
suggested by Philippe.
The values below are those to expect from the first flash device of
the FMC controller of a palmetto-bmc machine.
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The FMC controller on the Aspeed SoCs support DMA to access the flash
modules. It can operate in a normal mode, to copy to or from the flash
module mapping window, or in a checksum calculation mode, to evaluate
the best clock settings for reads.
The model introduces two custom address spaces for DMAs: one for the
AHB window of the FMC flash devices and one for the DRAM. The latter
is populated using a "dram" link set from the machine with the RAM
container region.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Improve the naming of the different controller models to ease their
generation when initializing the SoC. The rename of the SMC types is
breaking migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-5-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GPIO pins are arranged in groups of 8 pins labeled A,B,..,Y,Z,AA,AB,AC.
(Note that the ast2400 controller only goes up to group AB).
A set has four groups (except set AC which only has one) and is
referred to by the groups it is composed of (eg ABCD,EFGH,...,YZAAAB).
Each set is accessed and controlled by a bank of 14 registers.
These registers operate on a per pin level where each bit in the register
corresponds to a pin, except for the command source registers. The command
source registers operate on a per group level where bits 24, 16, 8 and 0
correspond to each group in the set.
eg. registers for set ABCD:
|D7...D0|C7...C0|B7...B0|A7...A0| <- GPIOs
|31...24|23...16|15....8|7.....0| <- bit position
Note that there are a couple of groups that only have 4 pins.
There are two ways that this model deviates from the behaviour of the
actual controller:
(1) The only control source driving the GPIO pins in the model is the ARM
model (as there currently aren't models for the LPC or Coprocessor).
(2) None of the registers in the model are reset tolerant (needs
integration with the watchdog).
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-2-clg@kaod.org
[clg: fixed missing header files
made use of HWADDR_PRIx to fix compilation on windows ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On Sparc and PowerMac, the bit 0 of the address selects the register
type (control or data) and bit 1 selects the channel (B or A).
On m68k Macintosh and NeXTcube, the bit 0 selects the channel and
bit 1 the register type.
This patch introduces a new parameter (bit_swap) to the device interface
to indicate bits usage must be swapped between registers and channels.
For the moment all the machines use the bit 0, but this change will be
needed to emulate the Quadra 800 or NeXTcube machine.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
[thh: added NeXTcube to the patch description]
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-5-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
It is still quite incomplete (no SCSI, no floppy emulation, no network,
etc.), but the firmware already shows up the debug monitor prompt in the
framebuffer display, so at least the very basics are already working.
This code has been taken from Bryce Lanham's GSoC 2011 NeXT branch at
https://github.com/blanham/qemu-NeXT/blob/next-cube/hw/next-cube.c
and altered quite a bit to fit the latest interface and coding conventions
of the current QEMU.
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-4-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
It is likely still quite incomplete (e.g. mouse and interrupts are not
implemented yet), but it is good enough for keyboard input at the firmware
monitor.
This code has been taken from Bryce Lanham's GSoC 2011 NeXT branch at
https://github.com/blanham/qemu-NeXT/blob/next-cube/hw/next-kbd.c
and altered to fit the latest interface of the current QEMU (e.g. to use
memory_region_init_io() instead of cpu_register_physical_memory()).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-3-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The NeXTcube uses a linear framebuffer with 4 greyscale colors and
a fixed resolution of 1120 * 832.
This code has been taken from Bryce Lanham's GSoC 2011 NeXT branch at
https://github.com/blanham/qemu-NeXT/blob/next-cube/hw/next-fb.c
and altered to fit the latest interface of the current QEMU (e.g.
the device has been "qdev"-ified etc.).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-2-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Reorganize watchpoints out of i/o path.
Return host address from probe_write / probe_access.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAl1uiyYdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV8AuwgAnYLQQbL8kjSqzp7q
gRlj0M2SX41ZW3fMkI794RwsljD9Z0QS7YGnpzHolig9XUYrGnip7STrMvlCr/1L
CIMWNHlgitgBMszLqg42/TB+6RxXn+DMX/ShUzTagC6xQhinCIpdEjoLaTKSgeP+
foIyJ2uoJLKOBP8cPTQp8evongtoQIljpsZZ0K8a4sreO1d6ytH+olkuoGiROft+
VoJkA+kNHd9cE+LPCva8UFGu1QE6uCySvhepzOpnvOtK+SXKUm2yLOFGu7RWP1pT
RkE0oRyRnImtg+cViHfUUFogIffFROdL5tuYMQVuqbINeROPUgJPav+R1Nz1P60a
xM2HEw==
=bLLU
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/pull-tcg-20190903' into staging
Allow page table bit to swap endianness.
Reorganize watchpoints out of i/o path.
Return host address from probe_write / probe_access.
# gpg: Signature made Tue 03 Sep 2019 16:47:50 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-tcg-20190903: (36 commits)
tcg: Factor out probe_write() logic into probe_access()
tcg: Make probe_write() return a pointer to the host page
s390x/tcg: Pass a size to probe_write() in do_csst()
hppa/tcg: Call probe_write() also for CONFIG_USER_ONLY
mips/tcg: Call probe_write() for CONFIG_USER_ONLY as well
tcg: Enforce single page access in probe_write()
tcg: Factor out CONFIG_USER_ONLY probe_write() from s390x code
s390x/tcg: Fix length calculation in probe_write_access()
s390x/tcg: Use guest_addr_valid() instead of h2g_valid() in probe_write_access()
tcg: Check for watchpoints in probe_write()
cputlb: Handle watchpoints via TLB_WATCHPOINT
cputlb: Remove double-alignment in store_helper
cputlb: Fix size operand for tlb_fill on unaligned store
exec: Factor out cpu_watchpoint_address_matches
cputlb: Fold TLB_RECHECK into TLB_INVALID_MASK
exec: Factor out core logic of check_watchpoint()
exec: Move user-only watchpoint stubs inline
target/sparc: sun4u Invert Endian TTE bit
target/sparc: Add TLB entry with attributes
cputlb: Byte swap memory transaction attribute
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
-----BEGIN PGP SIGNATURE-----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=u5HZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine + x86 queue, 2019-09-03
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
# gpg: Signature made Tue 03 Sep 2019 21:57:37 BST
# gpg: using RSA key 5A322FD5ABC4D3DBACCFD1AA2807936F984DC5A6
# gpg: issuer "ehabkost@redhat.com"
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
migration: Do not re-read the clock on pre_save in case of paused guest
x86: do not advertise die-id in query-hotpluggbale-cpus if '-smp dies' is not set
i386/vmmouse: Properly reset state
hostmem-file: fix pmem file size check
qapi: report the default CPU type for each machine
pc: Don't make die-id mandatory unless necessary
pc: Improve error message when die-id is omitted
pc: Fix error message on die-id validation
numa: move numa global variable numa_info into MachineState
numa: move numa global variable have_numa_distance into MachineState
numa: move numa global variable nb_numa_nodes into MachineState
hw/arm: simplify arm_load_dtb
includes: remove stale [smp|max]_cpus externs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The default backend is only used within virtio_rng_device_realize().
Replace VirtIORNGConf member default_backend by a local variable.
Adjust its type to reduce conversions.
While there, pass &error_abort instead of NULL when failure would be a
programming error.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20190820160615.14616-3-lvivier@redhat.com>
We want to move the check for watchpoints from
memory_region_section_get_iotlb to tlb_set_page_with_attrs.
Isolate the loop over watchpoints to an exported function.
Rename the existing cpu_watchpoint_address_matches to
watchpoint_address_matches, since it doesn't actually
have a cpu argument.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We want to perform the same checks in probe_write() to trigger a cpu
exit before doing any modifications. We'll have to pass a PC.
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190823100741.9621-9-david@redhat.com>
[rth: Use vaddr for len, like other watchpoint functions;
Move user-only stub to static inline.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Let the user-only watchpoint stubs resolve to empty inline functions.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add struct NumaState in MachineState and move existing numa global
nb_numa_nodes(renamed as "num_nodes") into NumaState. And add variable
numa_support into MachineClass to decide which submachines support NUMA.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-3-tao3.xu@intel.com>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In struct arm_boot_info, kernel_filename, initrd_filename and
kernel_cmdline are copied from from MachineState. This patch add
MachineState as a parameter into arm_load_dtb() and move the copy chunk
of kernel_filename, initrd_filename and kernel_cmdline into
arm_load_kernel().
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-2-tao3.xu@intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Cédric Le Goater <clg@kaod.org>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The QEMU coding style requires:
- to typedef structured types (HACKING)
- to use CamelCase for types and structure names (CODING_STYLE)
Do that for PCI and Nvlink2 code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156701644465.505236.2850655823182656869.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries guests do not normally allocate PCI resources and rely on
the system firmware doing so. Furthermore at least at some point in
the past the pseries guests won't even allowed to change BARs, probably
it is still the case for phyp. So since the initial commit we have [1]
which prevents resource reallocation.
This is not a problem until we want specific BAR alignments, for example,
PAGE_SIZE==64k to make sure we can still map MMIO BARs directly. For
the boot time devices we handle this in SLOF [2] but since QEMU's RTAS
does not allocate BARs, the guest does this instead and does not align
BARs even if Linux is given pci=resource_alignment=16@pci:0:0 as
PCI_PROBE_ONLY makes Linux ignore alignment requests.
ARM folks added a dial to control PCI_PROBE_ONLY via the device tree [3].
This makes use of the dial to advertise to the guest that we can handle
BAR reassignments. This limits the change to the latest pseries machine
to avoid old guests explosion.
We do not remove the flag from [1] as pseries guests are still supported
under phyp so having that removed may cause problems.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/powerpc/platforms/pseries/setup.c?h=v5.1#n773
[2] https://git.qemu.org/?p=SLOF.git;a=blob;f=board-qemu/slof/pci-phb.fs;h=06729bcf77a0d4e900c527adcd9befe2a269f65d;hb=HEAD#l338
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f81c11af
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190719043734.108462-1-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The xen_[rw]?mb() macros defined in ring.h can't be used and the fact
that there are gated behind __XEN_INTERFACE_VERSION__ means that it
needs to be defined somewhere. QEMU doesn't implement interfaces with
the Xen hypervisor so defining __XEN_INTERFACE_VERSION__ is pointless.
This leads to:
include/hw/xen/io/ring.h:47:5: error: "__XEN_INTERFACE_VERSION__"
is not defined, evaluates to 0 [-Werror=undef]
Cleanup ring.h. The xen_*mb() macros are already defined in xenctrl.h
which is included in xen_common.h.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190704153605.4140-1-anthony.perard@citrix.com>
[aperard: Adding the comment proposed upstream]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KtI3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kraxel/tags/audio-20190821-pull-request' into staging
audio: second batch of -audiodev support, adding support for multiple backends.
# gpg: Signature made Wed 21 Aug 2019 09:40:37 BST
# gpg: using RSA key 4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>" [full]
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>" [full]
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>" [full]
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/kraxel/tags/audio-20190821-pull-request:
audio: fix memory leak reported by ASAN
audio: use size_t where makes sense
audio: remove read and write pcm_ops
paaudio: fix playback glitches
audio: do not run each backend in audio_run
audio: remove audio_MIN, audio_MAX
paaudio: properly disconnect streams in fini_*
paaudio: do not move stream when sink/source name is specified
audio: audiodev= parameters no longer optional when -audiodev present
paaudio: prepare for multiple audiodev
audio: add audiodev properties to frontends
audio: add audiodev property to vnc and wav_capture
audio: basic support for multi backend audio
audio: reduce glob_audio_state usage
audio: Add missing fall through comments
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
First ppc and spapr pull request for qemu-4.2. Includes:
* Some TCG emulation fixes and performance improvements
* Support for the mffsl instruction in TCG
* Added missing DPDES SPR
* Some enhancements to the emulation of the XIVE interrupt
controller
* Cleanups to spapr MSI management
* Some new suspend/resume infrastructure and a draft suspend
implementation for spapr
* New spapr hypercall for TPM communication (will be needed for
secure guests under an Ultravisor)
* Fix several memory leaks
And a few other assorted fixes.
-----BEGIN PGP SIGNATURE-----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=E+7d
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20190821' into staging
ppc patch queue for 2019-08-21
First ppc and spapr pull request for qemu-4.2. Includes:
* Some TCG emulation fixes and performance improvements
* Support for the mffsl instruction in TCG
* Added missing DPDES SPR
* Some enhancements to the emulation of the XIVE interrupt
controller
* Cleanups to spapr MSI management
* Some new suspend/resume infrastructure and a draft suspend
implementation for spapr
* New spapr hypercall for TPM communication (will be needed for
secure guests under an Ultravisor)
* Fix several memory leaks
And a few other assorted fixes.
# gpg: Signature made Wed 21 Aug 2019 08:24:44 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20190821: (42 commits)
ppc: Fix emulated single to double denormalized conversions
ppc: Fix emulated INFINITY and NAN conversions
ppc: conform to processor User's Manual for xscvdpspn
ppc: Add support for 'mffsl' instruction
target/ppc: Add Directed Privileged Door-bell Exception State (DPDES) SPR
spapr/xive: Mask the EAS when allocating an IRQ
spapr: Implement better workaround in spapr-vty device
spapr/irq: Drop spapr_irq_msi_reset()
spapr/pci: Free MSIs during reset
spapr/pci: Consolidate de-allocation of MSIs
ppc: remove idle_timer logic
spapr: Implement ibm,suspend-me
i386: use machine class ->wakeup method
machine: Add wakeup method to MachineClass
ppc/xive: Improve 'info pic' support
ppc/xive: Provide silent escalation support
ppc/xive: Provide unconditional escalation support
ppc/xive: Provide escalation support
ppc/xive: Provide backlog support
ppc/xive: Implement TM_PULL_OS_CTX special command
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
PHBs already take care of clearing the MSIs from the bitmap during reset
or unplug. No need to do this globally from the machine code. Rather add
an assert to ensure that PHBs have acted as expected.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156415228966.1064338.190189424190233355.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix crash in qtest case where spapr->irq_map can be NULL at the
new assert()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This has been useful to modify and test the Linux pseries suspend
code but it requires modification to the guest to call it (due to
being gated by other unimplemented features). It is not otherwise
used by Linux yet, but work is slowly progressing there.
This allows a (lightly modified) guest kernel to suspend with
`echo mem > /sys/power/state` and be resumed with system_wakeup
monitor command.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190722061752.22114-2-npiggin@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Waking from suspend is not logically a machine reset on all machines,
particularly in the paravirtualized case rather than hardware
emulated. The ppc spapr machine for example just invokes hypervisor
to suspend, and expects that call to return with the machine in the
same state (modulo some possible migration and reconfiguration
details).
Implement a machine ->wakeup method and use that if it exists.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190722053215.20808-2-npiggin@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a better output of the XIVE END structures including the
escalation information and extend the PowerNV machine 'info pic'
command with a dump of the END EAS table used for escalations.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the 's' bit is set the escalation is said to be 'silent' or
'silent/gather'. In such configuration, the notification sequence is
skipped and only the escalation sequence is performed. This is used to
configure all the EQs of a vCPU to escalate on a single EQ which will
then target the hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the 'u' bit is set the escalation is said to be 'unconditional'
which means that the ESe PQ bits are not used. Introduce a
xive_router_end_es_notify() routine to share code with the ESn
notification.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This implements the H_TPM_COMM hypercall, which is used by an
Ultravisor to pass TPM commands directly to the host's TPM device, or
a TPM Resource Manager associated with the device.
This also introduces a new virtual device, spapr-tpm-proxy, which
is used to configure the host TPM path to be used to service
requests sent by H_TPM_COMM hcalls, for example:
-device spapr-tpm-proxy,id=tpmp0,host-path=/dev/tpmrm0
By default, no spapr-tpm-proxy will be created, and hcalls will return
H_FUNCTION.
The full specification for this hypercall can be found in
docs/specs/ppc-spapr-uv-hcalls.txt
Since SVM-related hcalls like H_TPM_COMM use a reserved range of
0xEF00-0xEF80, we introduce a separate hcall table here to handle
them.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com
Message-Id: <20190717205842.17827-3-mdroth@linux.vnet.ibm.com>
[dwg: Corrected #include for upstream change]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
H_PROD is added, and H_CEDE is modified to test the prod bit
according to PAPR.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-3-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement cpu_exec_enter/exit on ppc which calls into new methods of
the same name in PPCVirtualHypervisorClass. These are used by spapr
to implement the splpar VPA dispatch counter initially.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-2-npiggin@gmail.com>
[dwg: Removed unnecessary CONFIG_USER_ONLY checks as suggested by gkurz]
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Finally add audiodev= options to audio frontends so users can specify
which backend to use when multiple backends exist. Not specifying an
audiodev= option currently causes the first audiodev to be used, this is
fixed in the next commit.
Example usage: -audiodev pa,id=foo -device AC97,audiodev=foo
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: d64db52dda2d0e9d97bc5ab1dd9adf724280fea1.1566168923.git.DirtY.iCE.hu@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add 4.2 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1, as 0788a56bd1 ("i386: Make unversioned CPU models be
aliases") states this should only transition to the latest cpu
model version in 4.3 (or later).
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190724103524.20916-1-cohuck@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to reduce the memory footprint we map into memory
the initrd using g_mapped_file_new() instead of reading it.
In this way we can share the initrd pages between multiple
instances of QEMU.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190724143105.307042-4-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to reduce the memory footprint we map into memory
the ELF to load using g_mapped_file_new_from_fd() instead of
reading each sections. In this way we can share the ELF pages
between multiple instances of QEMU.
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190724143105.307042-3-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch allows handling an ELF memory-mapped, taking care
the reference count of the GMappedFile* passed through
rom_add_elf_program().
In this case, the 'data' pointer is not heap-allocated, so
we cannot free it.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190724143105.307042-2-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 1800 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h, down from 5400 due to the
previous commit).
Several headers include sysemu/sysemu.h just to get typedef
VMChangeStateEntry. Move it from sysemu/sysemu.h to qemu/typedefs.h.
Spell its structure tag the same while there. Drop the now
superfluous includes of sysemu/sysemu.h from headers.
Touching sysemu/sysemu.h now recompiles some 1100 objects.
qemu/uuid.h also drops from 1800 to 1100, and
qapi/qapi-types-run-state.h from 5000 to 4400.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-29-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Move the HostMemoryBackend typedef from sysemu/hostmem.h to
qemu/typedefs.h. This renders a few inclusions of sysemu/hostmem.h
superfluous; drop them.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-25-armbru@redhat.com>
sysemu/numa.h includes hw/boards.h just for the CPUArchId typedef, at
the cost of pulling in more than two dozen extra headers indirectly.
I could move the typedef from hw/boards.h to qemu/typedefs.h. But
it's used in just two headers: boards.h and numa.h.
I could move it to another header both its users include.
exec/cpu-common.h seems to be the least bad fit.
But I'm keeping this simple & stupid: declare the struct tag in
numa.h.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-24-armbru@redhat.com>
hw/boards.h pulls in almost 60 headers. The less we include it into
headers, the better. As a first step, drop superfluous inclusions,
and downgrade some more to what's actually needed. Gets rid of just
one inclusion into a header.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-20-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
hw/hw.h used to include headers hardware emulation "usually" needs.
The previous commits removed all but one of them, to good effect.
Only qom/object.h is left. Remove that one, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-18-armbru@redhat.com>
Drop unnecessary inclusions from headers. Downgrade a few more to
exec/hwaddr.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-17-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We declare incomplete struct VMStateDescription in a couple of places
so we don't have to include migration/vmstate.h for the typedef.
That's fine with me. However, the next commit will drop
migration/vmstate.h from a massive number of compiles. Move the
typedef to qemu/typedefs.h now, so I don't have to insert struct in
front of VMStateDescription all over the place then.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-15-armbru@redhat.com>
migration/qemu-file.h neglects to include it even though it needs
ram_addr_t. Fix that. Drop a few superfluous inclusions elsewhere.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-14-armbru@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
According to hw/ide/internal's file comment, only files in hw/ide/ are
supposed to include it. Drag reality slightly closer to supposition.
Three includes outside hw/ide remain: hw/arm/sbsa-ref.c,
include/hw/ide/pci.h, and include/hw/misc/macio/macio.h. Turns out
board code needs ide-internal.h to wire up IDE stuff. More cleanup is
needed. Left for another day.
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-11-armbru@redhat.com>
In my "build everything" tree, changing migration/qemu-file-types.h
triggers a recompile of some 2600 out of 6600 objects (not counting
tests and objects that don't depend on qemu/osdep.h).
The culprit is again hw/hw.h, which supposedly includes it for
convenience.
Include migration/qemu-file-types.h only where it's needed. Touching
it now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
Some of the generated qapi-types-MODULE.h are included all over the
place. Changing a QAPI type can trigger massive recompiling. Top
scorers recompile more than 1000 out of some 6600 objects (not
counting tests and objects that don't depend on qemu/osdep.h):
6300 qapi/qapi-builtin-types.h
5700 qapi/qapi-types-run-state.h
3900 qapi/qapi-types-common.h
3300 qapi/qapi-types-sockets.h
3000 qapi/qapi-types-misc.h
3000 qapi/qapi-types-crypto.h
3000 qapi/qapi-types-job.h
3000 qapi/qapi-types-block-core.h
2800 qapi/qapi-types-block.h
1300 qapi/qapi-types-net.h
Clean up headers to include generated QAPI headers only where needed.
Impact is negligible except for hw/qdev-properties.h.
This header includes qapi/qapi-types-block.h and
qapi/qapi-types-misc.h. They are used only in expansions of property
definition macros such as DEFINE_PROP_BLOCKDEV_ON_ERROR() and
DEFINE_PROP_OFF_AUTO(). Moving their inclusion from
hw/qdev-properties.h to the users of these macros avoids pointless
recompiles. This is how other property definition macros, such as
DEFINE_PROP_NETDEV(), already work.
Improves things for some of the top scorers:
3600 qapi/qapi-types-common.h
2800 qapi/qapi-types-sockets.h
900 qapi/qapi-types-misc.h
2200 qapi/qapi-types-crypto.h
2100 qapi/qapi-types-job.h
2100 qapi/qapi-types-block-core.h
270 qapi/qapi-types-block.h
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-3-armbru@redhat.com>
Back in 2016, we discussed[1] rules for headers, and these were
generally liked:
1. Have a carefully curated header that's included everywhere first. We
got that already thanks to Peter: osdep.h.
2. Headers should normally include everything they need beyond osdep.h.
If exceptions are needed for some reason, they must be documented in
the header. If all that's needed from a header is typedefs, put
those into qemu/typedefs.h instead of including the header.
3. Cyclic inclusion is forbidden.
This patch gets include/ closer to obeying 2.
It's actually extracted from my "[RFC] Baby steps towards saner
headers" series[2], which demonstrates a possible path towards
checking 2 automatically. It passes the RFC test there.
[1] Message-ID: <87h9g8j57d.fsf@blackfin.pond.sub.org>
https://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg03345.html
[2] Message-Id: <20190711122827.18970-1-armbru@redhat.com>
https://lists.nongnu.org/archive/html/qemu-devel/2019-07/msg02715.html
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-2-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The migration sequence of a guest using the XIVE exploitation mode
relies on the fact that the states of all devices are restored before
the machine is. This is not true for hot-plug devices such as CPUs
which state come after the machine. This breaks migration because the
thread interrupt context registers are not correctly set.
Fix migration of hotplugged CPUs by restoring their context in the
'post_load' handler of the XiveTCTX model.
Fixes: 277dd3d771 ("spapr/xive: add migration support for KVM")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190813064853.29310-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ACS was added in 4.0 unconditionally, this breaks migration
compatibility.
Allow ACS to be disabled by adding a property that's
checked by pcie_root_port.
Unfortunately pcie-root-port doesn't have any instance data,
so there's no where for that flag to live, so stuff it into
PCIESlot.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190730093719.12958-2-dgilbert@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit 8fa70dbd8b.
Because we're about to revert it's neighbour and thus uses an optional
again.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190729162903.4489-2-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
We still have multiple issues in the current code
- The PBP is not freed during unrealize()
- The PBP is not reset on device resets: After a reset, the PBP is stale.
- We are not indicating VIRTIO_BALLOON_F_MUST_TELL_HOST, therefore
guests (esp. legacy guests) will reuse pages without deflating,
turning the PBP stale. Adding that would require compat handling.
Instead, let's use the PBP only temporarily, when processing one bulk of
inflation requests. This will keep guest_page_size > 4k working (with
Linux guests). There is nothing to do for deflation requests anymore.
The pbp is only used for a limited amount of time.
Fixes: ed48c59875 ("virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size")
Cc: qemu-stable@nongnu.org #v4.0.0
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190722134108.22151-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The i.MX6UL always has a single Cortex-A7 CPU (we set FSL_IMX6UL_NUM_CPUS
to 1 in line with this). This means that all the code in fsl-imx6ul.c to
handle multiple CPUs is dead code, and Coverity is now complaining that
it is unreachable (CID 1403008, 1403011).
Remove the unreachable code and the only-executes-once loops,
and replace the single-entry cpu[] array in the FSLIMX6ULState
with a simple cpu member.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190712115030.26895-1-peter.maydell@linaro.org
The argument is not used and passing it clutters error propagation in the
callers. So, get rid of it.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the user hasn't specified a firmware to load (with -bios) or
specified no bios (with -bios none) then load OpenSBI by default. This
allows users to boot a RISC-V kernel with just -kernel.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The PL031 RTC tracks the difference between the guest RTC
and the host RTC using a tick_offset field. For migration,
however, we currently always migrate the offset between
the guest and the vm_clock, even if the RTC clock is not
the same as the vm_clock; this was an attempt to retain
migration backwards compatibility.
Unfortunately this results in the RTC behaving oddly across
a VM state save and restore -- since the VM clock stands still
across save-then-restore, regardless of how much real world
time has elapsed, the guest RTC ends up out of sync with the
host RTC in the restored VM.
Fix this by migrating the raw tick_offset. To retain migration
compatibility as far as possible, we have a new property
migrate-tick-offset; by default this is 'true' and we will
migrate the true tick offset in a new subsection; if the
incoming data has no subsection we fall back to the old
vm_clock-based offset information, so old->new migration
compatibility is preserved. For complete new->old migration
compatibility, the property is set to 'false' for 4.0 and
earlier machine types (this will only affect 'virt-4.0'
and below, as none of the other pl031-using machines are
versioned).
Reported-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20190709143912.28905-1-peter.maydell@linaro.org
The virtio-balloon config size changed in QEMU 4.0 even for existing
machine types. Migration from QEMU 3.1 to 4.0 can fail in some
circumstances with the following error:
qemu-system-x86_64: get_pci_config_device: Bad config data: i=0x10 read: a1 device: 1 cmask: ff wmask: c0 w1cmask:0
This happens because the virtio-balloon config size affects the VIRTIO
Legacy I/O Memory PCI BAR size.
Introduce a qdev property called "qemu-4-0-config-size" and enable it
only for the QEMU 4.0 machine types. This way <4.0 machine types use
the old size, 4.0 uses the larger size, and >4.0 machine types use the
appropriate size depending on enabled virtio-balloon features.
Live migration to and from old QEMUs to QEMU 4.1 works again as long as
a versioned machine type is specified (do not use just "pc"!).
Originally-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190710141440.27635-1-stefanha@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The function declarations for pci_cap_slot_get and
pci_cap_slot_write_config call the argument "slot_ctl", but the function
definitions and all the call sites drop the 'o' and call it "slt_ctl".
Let's be consistent.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Children sometimes depend on their parent's vm change state handler
having completed. Add a vm change state handler API for devices that
guarantees tree depth ordering.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This will make unversioned CPU models behavior depend on the
machine type:
* "pc-*-4.0" and older will not report them as aliases.
This is done to keep compatibility with older QEMU versions
after management software starts translating aliases.
* "pc-*-4.1" will translate unversioned CPU models to -v1.
This is done to keep compatibility with existing management
software, that still relies on CPU model runnability promises.
* "none" will translate unversioned CPU models to their latest
version. This is planned become the default in future machine
types (probably in pc-*-4.3).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-8-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To make smp_parse() more flexible and expansive, a smp_parse function
pointer is added to MachineClass that machine types could override.
The generic smp_parse() code in vl.c is moved to hw/core/machine.c, and
become the default implementation of MachineClass::smp_parse. A PC-specific
function called pc_smp_parse() has been added to hw/i386/pc.c, which in
this patch changes nothing against the default one .
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190620054525.37188-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Legacy '-numa node,mem' option has a number of issues and mgmt often
defaults to it. Unfortunately it's no possible to replace it with
an alternative '-numa memdev' without breaking migration compatibility.
What's possible though is to deprecate it, keeping option working with
old machine types only.
In order to help users to find out if being deprecated CLI option
'-numa node,mem' is still supported by particular machine type, add new
"numa-mem-supported" property to output of query-machines.
"numa-mem-supported" is set to 'true' for machines that currently support
NUMA, but it will be flipped to 'false' later on, once deprecation period
expires and kept 'true' only for old machine types that used to support
the legacy option so it won't break existing configuration that are using
it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1560172207-378962-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In new sockets/dies/cores/threads model, the apicid of logical cpu could
imply die level info of guest cpu topology thus x86_apicid_from_cpu_idx()
need to be refactored with #dies value, so does apicid_*_offset().
To keep semantic compatibility, the legacy pkg_offset which helps to
generate CPUIDs such as 0x3 for L3 cache should be mapping to die_offset.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-5-like.xu@linux.intel.com>
[ehabkost: squash unit test patch]
Message-Id: <20190612084104.34984-6-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The field die_id (default as 0) and has_die_id are introduced to X86CPU.
Following the legacy smp check rules, the die_id validity is added to
the same contexts as leagcy smp variables such as hmp_hotpluggable_cpus(),
machine_set_cpu_numa_node(), cpu_slot_to_string() and pc_cpu_pre_plug().
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-4-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The die-level as the first PC-specific cpu topology is added to the leagcy
cpu topology model, which has one die per package implicitly and only the
numbers of sockets/cores/threads are configurable.
In the new model with die-level support, the total number of logical
processors (including offline) on board will be calculated as:
#cpus = #sockets * #dies * #cores * #threads
and considering compatibility, the default value for #dies would be
initialized to one in x86_cpu_initfn() and pc_machine_initfn().
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-2-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To get rid of the global smp_* variables we're currently using, it's recommended
to pass MachineState in the list of incoming parameters for functions that use
global smp variables, thus some redundant parameters are dropped. It's applied
for legacy smbios_*(), *_machine_reset(), hot_add_cpu() and mips *_create_cpu().
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The cpu topology property CpuTopology is added to the MachineState
and its members are initialized with the leagcy global smp variables.
From this commit, the code in the system emulation mode is supposed to
use cpu topology variables from MachineState instead of the global ones
defined in vl.c and there is no semantic change.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-2-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
virtio-pmem support.
libvhost user mq support.
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEbBAABAgAGBQJdHmkBAAoJECgfDbjSjVRpEAIH+Kmy8n5Et9NzsnmNqHAiC/pg
3V5wGyp9M4ZJVPXC0z/Q1sYJ3YYP6dBd4tjj2/7LzYZSlqlQIs83UlQCo0XTiliH
/jZD/IaAZABnfB7vAeZW67WNT2a20xG2Jr83083lSaDUI/pfIdvbMelIbBLmo/kd
tWdAAWT0kcGYjyz4xQQgtAH6zAQUleKE7ECUJ2TpJQbSMLxdI/YTaoYqek471YdP
ju5OLBO3WbNkSE9JYz4MJqTudYK0sKu568UqBVF8JdpFd5Cv+X/OI+bCsc4QK8KN
DTtFVVvbm1KGPSceqc9rwsDjO4Wd8ThvuZxrB029AahD6vT82F13IHpi/S29Fw==
=WAFb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pc, pci: features, fixes, cleanups
virtio-pmem support.
libvhost user mq support.
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 04 Jul 2019 22:00:49 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
docs: avoid vhost-user-net specifics in multiqueue section
libvhost-user: implement VHOST_USER_PROTOCOL_F_MQ
libvhost-user: support many virtqueues
libvhost-user: add vmsg_set_reply_u64() helper
pc: Move compat_apic_id_mode variable to PCMachineClass
virtio: Don't change "started" flag on virtio_vmstate_change()
virtio: Make sure we get correct state of device on handle_aio_output()
virtio: Set "start_on_kick" on virtio_set_features()
virtio: Set "start_on_kick" for legacy devices
virtio: add "use-started" property
virtio-pci: fix missing device properties
pc: Support for virtio-pmem-pci
numa: Handle virtio-pmem in NUMA stats
hmp: Handle virtio-pmem when printing memory device infos
virtio-pci: Proxy for virtio-pmem
virtio-pmem: sync linux headers
virtio-pci: Allow to specify additional interfaces for the base type
virtio-pmem: add virtio device
pcie: minor cleanups for slot control/status
pcie: work around for racy guest init
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace the static variable with a PCMachineClass field. This
will help us eventually get rid of the pc_compat_*() init
functions.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628200227.1053-1-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Besides virtio 1.0 transitional devices, we should also
set "start_on_kick" flag for legacy devices (virtio 0.9).
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190626023130.31315-3-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to avoid migration issues, we introduce a "use-started"
property to the base virtio device to indicate whether use
"started" flag or not. This property will be true by default and
set to false when machine type <= 4.0.
Suggested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Message-Id: <20190626023130.31315-2-xieyongji@baidu.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We need a proxy device for virtio-pmem, and this device has to be the
actual memory device so we can cleanly hotplug it.
Forward memory device class functions either to the actual device or use
properties of the virtio-pmem device to implement these in the proxy.
virtio-pmem will only be compiled for selected, supported architectures
(that can deal with virtio/pci devices being memory devices). An
architecture that is prepared for that can simply enable
CONFIG_VIRTIO_PMEM to make it work.
As not all architectures support memory devices (and CONFIG_VIRTIO_PMEM
will be enabled per supported architecture), we have to move the PCI proxy
to a separate file.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
[ split up patches, memory-device changes, move pci proxy]
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190619094907.10131-5-pagupta@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This pull request contains a handful of patches that I'd like to target
for the 4.1 soft freeze. There are a handful of new features:
* Support for the 1.11.0, the latest privileged specification.
* Support for reading and writing the PRCI registers.
* Better control over the ISA of the target machine.
* Support for the cpu-topology device tree node.
Additionally, there are a handful of bug fixes including:
* Load reservations are now broken by both store conditional and by
scheduling, which fixes issues with parallel applications.
* Various fixes to the PMP implementation.
* Fixes to the 32-bit linux-user syscall ABI.
* Various fixes for instruction decodeing.
* A fix to the PCI device tree "bus-range" property.
This boots 32-bit and 64-bit OpenEmbedded.
Changes since v2 [riscv-for-master-4.1-sf1-v2]:
* Dropped OpenSBI.
Changes since v1 [riscv-for-master-4.1-sf1]:
* Contains a fix to the sifive_u OpenSBI integration.
-----BEGIN PGP SIGNATURE-----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=lliO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.1-sf1-v3' into staging
RISC-V Patches for the 4.1 Soft Freeze, Part 2 v3
This pull request contains a handful of patches that I'd like to target
for the 4.1 soft freeze. There are a handful of new features:
* Support for the 1.11.0, the latest privileged specification.
* Support for reading and writing the PRCI registers.
* Better control over the ISA of the target machine.
* Support for the cpu-topology device tree node.
Additionally, there are a handful of bug fixes including:
* Load reservations are now broken by both store conditional and by
scheduling, which fixes issues with parallel applications.
* Various fixes to the PMP implementation.
* Fixes to the 32-bit linux-user syscall ABI.
* Various fixes for instruction decodeing.
* A fix to the PCI device tree "bus-range" property.
This boots 32-bit and 64-bit OpenEmbedded.
Changes since v2 [riscv-for-master-4.1-sf1-v2]:
* Dropped OpenSBI.
Changes since v1 [riscv-for-master-4.1-sf1]:
* Contains a fix to the sifive_u OpenSBI integration.
# gpg: Signature made Wed 03 Jul 2019 09:39:09 BST
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.1-sf1-v3: (32 commits)
hw/riscv: Extend the kernel loading support
hw/riscv: Add support for loading a firmware
hw/riscv: Split out the boot functions
riscv: sifive_u: Update the plic hart config to support multicore
riscv: sifive_u: Do not create hard-coded phandles in DT
disas/riscv: Fix `rdinstreth` constraint
disas/riscv: Disassemble reserved compressed encodings as illegal
riscv: virt: Add cpu-topology DT node.
RISC-V: Update syscall list for 32-bit support.
RISC-V: Clear load reservations on context switch and SC
RISC-V: Add support for the Zicsr extension
RISC-V: Add support for the Zifencei extension
target/riscv: Add support for disabling/enabling Counters
target/riscv: Remove user version information
target/riscv: Require either I or E base extension
qemu-deprecated.texi: Deprecate the RISC-V privledge spec 1.09.1
target/riscv: Set privledge spec 1.11.0 as default
target/riscv: Add the mcountinhibit CSR
target/riscv: Add the privledge spec version 1.11.0
target/riscv: Restructure deprecatd CPUs
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the bitbang_i2c_init() function allocates a
bitbang_i2c_interface struct which it returns. This is unfortunate
because it means that if the function is used from a DeviceState
init method then the memory will be leaked by an "init then delete"
cycle, as used by the qmp/hmp commands that list device properties.
Since three out of four of the uses of this function are in
device init methods, switch the function to do an in-place
initialization of a struct that can be embedded in the
device state struct of the caller.
This fixes LeakSanitizer leak warnings that have appeared in the
patchew configuration (which only tries to run the sanitizers
for the x86_64-softmmu target) now that we use the bitbang-i2c
code in an x86-64 config.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190702163844.20458-1-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is a left-over from "f4ec5e26ed vfio: Add host side DMA window
capabilities", which added support to more than one DMA window.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Here's my next pull request for qemu-4.1. I'm not sure if this will
squeak in just before the soft freeze, or just after. I don't think
it really matters - most of this is bugfixes anyway. There's some
cleanups which aren't stictly bugfixes, but which I think are safe
enough improvements to go in the soft freeze. There's no true feature
work.
Unfortunately, I wasn't able to complete a few of my standard battery
of pre-pull tests, due to some failures that appear to also be in
master. I'm hoping that hasn't missed anything important in here.
Highlights are:
* A number of fixe and cleanups for the XIVE implementation
* Cleanups to the XICS interrupt controller to fit better with the new
XIVE code
* Numerous fixes and improvements to TCG handling of ppc vector
instructions
* Remove a number of unnnecessary #ifdef CONFIG_KVM guards
* Fix some errors in the PCI hotplug paths
* Assorted other fixes
-----BEGIN PGP SIGNATURE-----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=QAyU
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190702' into staging
ppc patch queue 2019-07-2
Here's my next pull request for qemu-4.1. I'm not sure if this will
squeak in just before the soft freeze, or just after. I don't think
it really matters - most of this is bugfixes anyway. There's some
cleanups which aren't stictly bugfixes, but which I think are safe
enough improvements to go in the soft freeze. There's no true feature
work.
Unfortunately, I wasn't able to complete a few of my standard battery
of pre-pull tests, due to some failures that appear to also be in
master. I'm hoping that hasn't missed anything important in here.
Highlights are:
* A number of fixe and cleanups for the XIVE implementation
* Cleanups to the XICS interrupt controller to fit better with the new
XIVE code
* Numerous fixes and improvements to TCG handling of ppc vector
instructions
* Remove a number of unnnecessary #ifdef CONFIG_KVM guards
* Fix some errors in the PCI hotplug paths
* Assorted other fixes
# gpg: Signature made Tue 02 Jul 2019 07:07:15 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190702: (49 commits)
spapr/xive: Add proper rollback to kvmppc_xive_connect()
ppc/xive: Fix TM_PULL_POOL_CTX special operation
ppc/pnv: Rework cache watch model of PnvXIVE
ppc/xive: Make the PIPR register readonly
ppc/xive: Force the Physical CAM line value to group mode
spapr/xive: simplify spapr_irq_init_device() to remove the emulated init
spapr/xive: rework the mapping the KVM memory regions
spapr_pci: Unregister listeners before destroying the IOMMU address space
target/ppc: improve VSX_FMADD with new GEN_VSX_HELPER_VSX_MADD macro
target/ppc: decode target register in VSX_EXTRACT_INSERT at translation time
target/ppc: decode target register in VSX_VECTOR_LOAD_STORE_LENGTH at translation time
target/ppc: introduce GEN_VSX_HELPER_R2_AB macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_R2 macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_R3 macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_X1 macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_X2_AB macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_X2 macro to fpu_helper.c
target/ppc: introduce separate generator and helper for xscvqpdp
target/ppc: introduce GEN_VSX_HELPER_X3 macro to fpu_helper.c
target/ppc: introduce separate VSX_CMP macro for xvcmp* instructions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the implementation of virtio-pmem device. Support will require
machine changes for the architectures that will support it, so it will
not yet be compiled. It can be unlocked with VIRTIO_PMEM_SUPPORTED per
machine and disabled globally via VIRTIO_PMEM.
We cannot use the "addr" property as that is already used e.g. for
virtio-pci/pci devices. And we will have e.g. virtio-pmem-pci as a proxy.
So we have to choose a different one (unfortunately). "memaddr" it is.
That name should ideally be used by all other virtio-* based memory
devices in the future.
-device virtio-pmem-pci,id=p0,bus=bux0,addr=0x01,memaddr=0x1000000...
Acked-by: Markus Armbruster <armbru@redhat.com>
[ QAPI bits ]
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
[ MemoryDevice/MemoryRegion changes, cleanups, addr property "memaddr",
split up patches, unplug handler ]
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190619094907.10131-2-pagupta@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Move commands cpu-add, query-cpus, query-cpus-fast,
query-current-machine, query-hotpluggable-cpus, query-machines,
query-memdev, and set-numa-node with their types from misc.json to new
machine.json. Also move types X86CPURegister32 and
X86CPUFeatureWordInfo. Add machine.json to MAINTAINERS section
"Machine core".
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-9-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
- fix for a tcg test case
- halt/clear support for vfio-ccw, and use a new helper
-----BEGIN PGP SIGNATURE-----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=0dnG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20190701' into staging
- cleanup/refactoring in the cpu feature code
- fix for a tcg test case
- halt/clear support for vfio-ccw, and use a new helper
# gpg: Signature made Mon 01 Jul 2019 12:08:41 BST
# gpg: using RSA key C3D0D66DC3624FF6A8C018CEDECF6B93C6F02FAF
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20190701:
s390x: add cpu feature/model files to KVM section
vfio-ccw: support async command subregion
vfio-ccw: use vfio_set_irq_signaling
s390x/cpumodel: Prepend KDSA features with "KDSA"
s390x/cpumodel: Rework CPU feature definition
tests/tcg/s390x: Fix alignment of csst parameter list
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The init_emu() handles are now empty. Remove them and rename
spapr_irq_init_device() to spapr_irq_init_kvm().
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190614165920.12670-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the interrupt device is fully initialized at reset when the CAS
negotiation process has completed. Depending on the KVM capabilities,
the SpaprXive memory regions (ESB, TIMA) are initialized with a host
MMIO backend or a QEMU emulated backend. This results in a complex
initialization sequence partially done at realize and later at reset,
and some memory region leaks.
To simplify this sequence and to remove of the late initialization of
the emulated device which is required to be done only once, we
introduce new memory regions specific for KVM. These regions are
mapped as overlaps on top of the emulated device to make use of the
host MMIOs. Also provide proper cleanups of these regions when the
XIVE KVM device is destroyed to fix the leaks.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190614165920.12670-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows errors happening there to be propagated up to spapr_irq,
just like XIVE already does.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077921763.433243.4614327010172954196.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch to using the connect/disconnect terminology like we already do for
XIVE.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077920102.433243.6605099291134598170.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 9fb6eb7ca50c added the declaration of xics_spapr_connect(), which
has no implementation and no users.
This is a leftover from a previous iteration of this patch. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077919546.433243.8748677531446035746.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Older KVMs on POWER9 don't support destroying/recreating a KVM XICS
device, which is required by 'dual' interrupt controller mode. This
causes QEMU to emit a warning when the guest is rebooted and to fall
back on XICS emulation:
qemu-system-ppc64: warning: kernel_irqchip allowed but unavailable:
Error on KVM_CREATE_DEVICE for XICS: File exists
If kernel irqchip is required, QEMU will thus exit when the guest is
first rebooted. Failing QEMU this late may be a painful experience
for the user.
Detect that and exit at machine init instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044430517.125694.6207865998817342638.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU may crash when running a spapr machine in 'dual' interrupt controller
mode on some older (but not that old, eg. ubuntu 18.04.2) KVMs with partial
XIVE support:
qemu-system-ppc64: hw/ppc/spapr_rtas.c:411: spapr_rtas_register:
Assertion `!name || !rtas_table[token].name' failed.
XICS is controlled by the guest thanks to a set of RTAS calls. Depending
on whether KVM XICS is used or not, the RTAS calls are handled by KVM or
QEMU. In both cases, QEMU needs to expose the RTAS calls to the guest
through the "rtas" node of the device tree.
The spapr_rtas_register() helper takes care of all of that: it adds the
RTAS call token to the "rtas" node and registers a QEMU callback to be
invoked when the guest issues the RTAS call. In the KVM XICS case, QEMU
registers a dummy callback that just prints an error since it isn't
supposed to be invoked, ever.
Historically, the XICS controller was setup during machine init and
released during final teardown. This changed when the 'dual' interrupt
controller mode was added to the spapr machine: in this case we need
to tear the XICS down and set it up again during machine reset. The
crash happens because we indeed have an incompatibility with older
KVMs that forces QEMU to fallback on emulated XICS, which tries to
re-registers the same RTAS calls.
This could be fixed by adding proper rollback that would unregister
RTAS calls on error. But since the emulated RTAS calls in QEMU can
now detect when they are mistakenly called while KVM XICS is in
use, it seems simpler to register them once and for all at machine
init. This fixes the crash and allows to remove some now useless
lines of code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044429963.125694.13710679451927268758.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It has now became useless with the previous patch.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190612174345.9799-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PNV_XSCOM_BASE and PNV_XSCOM_SIZE macros are specific to POWER8
and they are used when the device tree is populated and the MMIO
region created, even for POWER9 chips. This is not too much of a
problem today because we don't have important devices on the second
chip, but we might have oneday (PHBs).
Fix by using the appropriate macros in case of P9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190612174345.9799-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ast2500 uses the watchdog to reset the SDRAM controller. This
operation is usually performed by u-boot's memory training procedure,
and it is enabled by setting a bit in the SCU and then causing the
watchdog to expire. Therefore, we need the watchdog to be able to
access the SCU's register space.
This causes the watchdog to not perform a system reset when the bit is
set. In the future it could perform a reset of the SDMC model.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190621065242.32535-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The XDMA engine embedded in the Aspeed SOCs performs PCI DMA operations
between the SOC (acting as a BMC) and a host processor in a server.
The XDMA engine exists on the AST2400, AST2500, and AST2600 SOCs, so
enable it for all of those. Add trace events on the important register
writes in the XDMA engine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-21-clg@kaod.org
[clg: - changed title ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DRAM address of a DMA transaction depends on the DRAM base address
of the SoC. Inform the SMC controller model with this value.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190618165311.27066-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoCs have two MACs. Extend the Aspeed model to support a
second NIC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current models of the Aspeed SoCs only have one CPU but future
ones will support SMP. Introduce a new num_cpus field at the SoC class
level to define the number of available CPUs per SoC and also
introduce a 'num-cpus' property to activate the CPUs configured for
the machine.
The max_cpus limit of the machine should depend on the SoC definition
but, unfortunately, these values are not available when the machine
class is initialized. This is the reason why we add a check on
num_cpus in the AspeedSoC realize handler.
SMP support will be activated when models for such SoCs are implemented.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All systems have an RTC.
The IRQ is hooked up but the model does not use it at this stage. There
is no guest code that uses it, so this limitation is acceptable.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RTC is modeled to provide time and date functionality. It is
initialised at zero to match the hardware.
There is no modelling of the alarm functionality, which includes the IRQ
line. As there is no guest code to exercise this function that is
acceptable for now.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a slightly different address space and have a different set
of controllers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a different CPU and a different IRQ number layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Datasheet for i.MX7 is incorrect and i.MX7's PCI IRQ mapping matches
that of i.MX6:
* INTD/MSI 122
* INTC 123
* INTB 124
* INTA 125
Fix all of the relevant code to reflect that fact. Needed by latest
Linux kernels.
(Reference: Linux kernel commit 538d6e9d597584e80 from an
NXP employee confirming that the datasheet is incorrect and
with a report of a test against hardware.)
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added ref to kernel commit confirming the datasheet error]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add no-op/unimplemented PCIE PHY IP block. Needed by new kernels to
use PCIE.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename function arguments to make intent clearer.
Better documentation for slot control logic.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
During boot, linux would sometimes overwrites control of a powered off
slot before powering it on. Unfortunately QEMU interprets that as a
power off request and ejects the device.
For example:
/x86_64-softmmu/qemu-system-x86_64 -enable-kvm -S -machine q35 \
-device pcie-root-port,id=pcie_root_port_0,slot=2,chassis=2,addr=0x2,bus=pcie.0 \
-monitor stdio disk.qcow2
(qemu)device_add virtio-balloon-pci,id=balloon,bus=pcie_root_port_0
(qemu)cont
Balloon is deleted during guest boot.
To fix, save control beforehand and check that power
or led state actually change before ejecting.
Note: this is more a hack than a solution, ideally we'd
find a better way to detect ejects, or move away
from ejects completely and instead monitor whether
it's safe to delete device due to e.g. its power state.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
The bitbang i2c implementation is also useful for other device models
such as DDC in display controllers. Move the header to include/hw/i2c/
to allow it to be used from other device models and adjust users of
this include. This also reverts commit 2b4c1125ac which is no longer
needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 5d1fe4db846ab9be4b77ddb0d43cc74cd200a003.1561028123.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add support for loading a firmware file for the virt machine and the
SiFive U. This can be run with the following command:
qemu-system-riscv64 -machine virt -bios fw_jump.bin -kernel vmlinux
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Split the common RISC-V boot functions into a seperate file. This allows
us to share the common code.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
A vfio-ccw device may provide an async command subregion for
issuing halt/clear subchannel requests. If it is present, use
it for sending halt/clear request to the device; if not, fall
back to emulation (as done today).
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <20190613092542.2834-1-cohuck@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
A Xen public header have been imported into QEMU (by
f65eadb639 "xen: import ring.h from xen"), but there are other header
that depends on ring.h which come from the system when building QEMU.
This patch resolves the issue of having headers from the system
importing a different copie of ring.h.
This patch is prompt by the build issue described in the previous
patch: 'Revert xen/io/ring.h of "Clean up a few header guard symbols"'
ring.h and the new imported headers are moved to
"include/hw/xen/interface" as those describe interfaces with a guest.
The imported headers are cleaned up a bit while importing them: some
part of the file that QEMU doesn't use are removed (description
of how to make hypercall in grant_table.h have been removed).
Other cleanup:
- xen-mapcache.c and xen-legacy-backend.c don't need grant_table.h.
- xenfb.c doesn't need event_channel.h.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190621105441.3025-3-anthony.perard@citrix.com>
This reverts changes to include/hw/xen/io/ring.h from commit
37677d7db3.
Following 37677d7db3 "Clean up a few header guard symbols", QEMU start
to fail to build:
In file included from ~/xen/tools/../tools/include/xen/io/blkif.h:31:0,
from ~/xen/tools/qemu-xen-dir/hw/block/xen_blkif.h:5,
from ~/xen/tools/qemu-xen-dir/hw/block/xen-block.c:22:
~/xen/tools/../tools/include/xen/io/ring.h:68:0: error: "__CONST_RING_SIZE" redefined [-Werror]
#define __CONST_RING_SIZE(_s, _sz) \
In file included from ~/xen/tools/qemu-xen-dir/hw/block/xen_blkif.h:4:0,
from ~/xen/tools/qemu-xen-dir/hw/block/xen-block.c:22:
~/xen/tools/qemu-xen-dir/include/hw/xen/io/ring.h:66:0: note: this is the location of the previous definition
#define __CONST_RING_SIZE(_s, _sz) \
The issue is that some public xen headers have been imported (by
f65eadb639 "xen: import ring.h from xen") but not all. With the change
in the guards symbole, the ring.h header start to be imported twice.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190621105441.3025-2-anthony.perard@citrix.com>
This patch introduces a poll callback for event channel fd-s and uses
this to invoke the channel callback function.
To properly support polling, it is necessary for the event channel callback
function to return a boolean saying whether it has done any useful work or
not. Thus xen_block_dataplane_event() is modified to directly invoke
xen_block_handle_requests() and the latter only returns true if it actually
processes any requests. This also means that the call to qemu_bh_schedule()
is moved into xen_block_complete_aio(), which is more intuitive since the
only reason for doing a deferred poll of the shared ring should be because
there were previously insufficient resources to fully complete a previous
poll.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-4-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds an AioContext parameter to xen_device_bind_event_channel()
and then uses aio_set_fd_handler() to set the callback rather than
qemu_set_fd_handler().
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-3-paul.durrant@citrix.com>
[Call aio_set_fd_handler() with is_external=true]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
To better support use of IOThread-s it will be necessary to be able to set
the AioContext for each XenEventChannel and hence it is necessary to open a
separate handle to libxenevtchan for each channel.
This patch stops using NotifierList for event channel callbacks, replacing
that construct by a list of complete XenEventChannel structures. Each of
these now has a xenevtchn_handle pointer in place of the single pointer
previously held in the XenDevice structure. The individual handles are
opened/closed in xen_device_bind/unbind_event_channel(), replacing the
single open/close in xen_device_realize/unrealize().
NOTE: This patch does not add an AioContext parameter to
xen_device_bind_event_channel(). That will be done in a subsequent
patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-2-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity pointed out a memory leak in riscv_sifive_e_soc_realize(),
where a pair of recently added MemoryRegion instances would not be freed
if there were errors elsewhere in the function. The fix here is to
simply not use dynamic allocation for these instances: there's always
one of each in SiFiveESoCState, so instead we just include them within
the struct.
Fixes: 30efbf330a ("SiFive RISC-V GPIO Device")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Writes to the SiFive PRCI registers are preserved while leaving the
ready bits set for the HFX/HFR oscillators and the lock bit set for the
PLL.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Commit c87759ce87 fixed a regression affecting pc-q35 machines by
introducing a new pc-q35-4.0.1 machine version to be used instead
of pc-q35-4.0. The only purpose was to revert the default behaviour
of not using split irqchip, but the change also introduced the usual
hw_compat and pc_compat bits, and wired them for pc-q35 only.
This raises questions when it comes to add new compat properties for
4.0* machine versions of any architecture. Where to add them ? In
4.0, 4.0.1 or both ? Error prone. Another possibility would be to teach
all other architectures about 4.0.1. This solution isn't satisfying,
especially since this is a pc-q35 specific issue.
It turns out that the split irqchip default is handled in the machine
option function and doesn't involve compat lists at all.
Drop all the 4.0.1 compat lists and use the 4.0 ones instead in the 4.0.1
machine option function.
Move the compat props that were added to the 4.0.1 since c87759ce87 to
4.0.
Even if only hw_compat_4_0_1 had an impact on other architectures,
drop pc_compat_4_0_1 as well for consistency.
Fixes: c87759ce87 "q35: Revert to kernel irqchip"
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <156051774276.244890.8660277280145466396.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SSE-200 hardware has configurable integration settings which
determine whether its two CPUs have the FPU and DSP:
* CPU0_FPU (default 0)
* CPU0_DSP (default 0)
* CPU1_FPU (default 1)
* CPU1_DSP (default 1)
Similarly, the IoTKit has settings for its single CPU:
* CPU0_FPU (default 1)
* CPU0_DSP (default 1)
Of our four boards that use either the IoTKit or the SSE-200:
* mps2-an505, mps2-an521 and musca-a use the default settings
* musca-b1 enables FPU and DSP on both CPUs
Currently QEMU models all these boards using CPUs with
both FPU and DSP enabled. This means that we are incorrect
for mps2-an521 and musca-a, which should not have FPU or DSP
on CPU0.
Create QOM properties on the ARMSSE devices corresponding to the
default h/w integration settings, and make the Musca-B1 board
enable FPU and DSP on both CPUs. This fixes the mps2-an521
and musca-a behaviour, and leaves the musca-b1 and mps2-an505
behaviour unchanged.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-5-peter.maydell@linaro.org
Create "vfp" and "dsp" properties on the armv7m container object
which will be forwarded to its CPU object, so that SoCs can
configure whether the CPU has these features.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-4-peter.maydell@linaro.org
arm and i386 has almost the same function acpi_add_rom_blob(), except
giving different FWCfgCallback function.
This patch moves acpi_add_rom_blob() to utils.c by passing
FWCfgCallback to it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v7:
* rebase on top of current master because of conflict
v6:
* change author from Igor to Michael
v5:
* remove unnecessary header glib/gprintf.h
* rearrange include header to make it more suitable
v4:
* extract -> moves
* adjust comment in source to make checkpatch happy
v3:
* put acpi_add_rom_blob() to hw/acpi/utils.c
v2:
* remove unused header in original source file
Message-Id: <20190610011830.28398-1-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The code used to assign an interrupt index/subindex to an
eventfd is duplicated many times. Let's introduce an helper that
allows to set/unset the signaling for an ACTION_TRIGGER,
ACTION_MASK or ACTION_UNMASK action.
In the error message, we now use errno in case of any
VFIO_DEVICE_SET_IRQS ioctl failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add new properties to allow setting the maximum display resolution.
Resolutions larger than that will not be included in the mode list.
In linux guests xrandr can be used to list modes.
Note: The existing xres and yres properties set the preferred display
resolution, i.e. the mode should be first in the mode list and guests
should use it by default.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190607083429.31943-1-kraxel@redhat.com
This is ostensibly to avoid the weirdness of len looking like it might
come from a guest and sometimes being used. While we are at it fix up
the error checking for the arm-linux-user implementation of the API
which got flagged up by Coverity (CID 1401700).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
-----BEGIN PGP SIGNATURE-----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=ERgu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190612' into staging
ppc patch queue 2019-06-12
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
# gpg: Signature made Wed 12 Jun 2019 06:47:56 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190612:
ppc/xive: Make XIVE generate the proper interrupt types
ppc/pnv: activate the "dumpdtb" option on the powernv machine
target/ppc: Use tcg_gen_gvec_bitsel
spapr: Allow hot plug/unplug of PCI bridges and devices under PCI bridges
spapr: Direct all PCI hotplug to host bridge, rather than P2P bridge
spapr: Don't use bus number for building DRC ids
spapr: Clean up DRC index construction
spapr: Clean up spapr_drc_populate_dt()
spapr: Clean up dt creation for PCI buses
spapr: Clean up device tree construction for PCI devices
spapr: Clean up device node name generation for PCI devices
target/ppc: Fix lxvw4x, lxvh8x and lxvb16x
spapr_pci: Improve error message
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 58ea30f514 "Clean up header guards that don't match their file
name" messed up contrib/elf2dmp/qemu_elf.h and
tests/migration/migration-test.h.
It missed target/cris/opcode-cris.h and
tests/uefi-test-tools/UefiTestToolsPkg/Include/Guid/BiosTablesTest.h
due to the scripts/clean-header-guards.pl bug fixed in the previous
commit.
Commit a8b991b52d "Clean up ill-advised or unusual header guards"
missed include/hw/xen/io/ring.h for the same reason.
Commit 3979fca4b6 "disas: Rename include/disas/bfd.h back to
include/disas/dis-asm.h" neglected to update the guard symbol for the
rename.
Commit a331c6d774 "semihosting: implement a semihosting console"
created include/hw/semihosting/console.h with an ill-advised guard
symbol.
Clean them up.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190604181618.19980-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This is the common header guard idiom:
/*
* File comment
*/
#ifndef GUARD_SYMBOL_H
#define GUARD_SYMBOL_H
... actual contents ...
#endif
A few of our headers have some #include before the guard.
target/tilegx/spr_def_64.h has #ifndef __DOXYGEN__ outside the guard.
A few more have the #define elsewhere.
Change them to match the common idiom. For spr_def_64.h, that means
dropping #ifndef __DOXYGEN__. While there, rename guard symbols to
make scripts/clean-header-guards.pl happy.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190604181618.19980-2-armbru@redhat.com>
[Rebased with conflicts resolved automatically]
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
It should be generic Hypervisor Virtualization interrupts for HV
directed rings and traditional External Interrupts for the OS directed
ring.
Don't generate anything for the user ring as it isn't actually
supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190606174409.12502-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes some minor cleanups to spapr_drc_populate_dt(), renaming it to
the shorter and more idiomatic spapr_dt_drc() along the way.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Device nodes for PCI bridges (both host and P2P) describe both the bridge
device itself and the bus hanging off it, handling of this is a bit of a
mess.
spapr_dt_pci_device() has a few things it only adds for non-bridges, but
always adds #address-cells and #size-cells which should only appear for
bridges. But the walking down the subordinate PCI bus is done in one of
its callers spapr_populate_pci_devices_dt(). The PHB dt creation in
spapr_populate_pci_dt() open codes some similar logic to the bridge case.
This patch consolidates things in a bunch of ways:
* Bus specific dt info is now created in spapr_dt_pci_bus() used for both
P2P bridges and the host bridge. This includes walking subordinate
devices
* spapr_dt_pci_device() now calls spapr_dt_pci_bus() when called on a
P2P bridge
* We do detection of bridges with the is_bridge field of the device class,
rather than checking PCI config space directly, for consistency with
qemu's core PCI code.
* Several things are renamed for brevity and clarity
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJc+B4YAAoJECgfDbjSjVRpq1EIAJR7tCxcpu9GggVlinmUA8G4
tmSAe06IryH7+nF3RsnINuGu7ius9qC2/E2y0uJUHhTqiU/RWOfWZ7PPM0EcYZaA
TLPaCe2NUF6/8afeqmvE9Usk7VspI5TDZRms+bonmZz2xP1lHIMN0qW4s7HHLWr8
sZKDtCJ+9cYII93VQwtlR0qiHgv5f0kzcuZeJaZHsAHH6XZGqRuQjI6txcFa4o53
lkdLCEwTnRuwu2wyL84eL5p+E8SzOgR/x1QI+nffrJfsvnmiT7lnOrkjnQlWAp5G
xqwqsUrUxUCuQ+zitwJqmv+H6nx79MwAM7fTHAETCWX703N5o9tZxAnHHqLoa8I=
=cQNg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci, pc: cleanups, features
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 05 Jun 2019 20:55:04 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
bios-tables-test: ignore identical binaries
tests: acpi: add simple arm/virt testcase
tests: add expected ACPI tables for arm/virt board
bios-tables-test: list all tables that differ
vhost-scsi: Allow user to enable migration
vhost-scsi: Add VMState descriptor
vhost-scsi: The vhost backend should be stopped when the VM is not running
bios-tables-test: add diff allowed list
vhost: fix memory leak in vhost_user_scsi_realize
vhost: fix incorrect print type
vhost: remove the dead code
docs: smbios: remove family=x from type2 entry description
pci: Fold pci_get_bus_devfn() into its sole caller
pci: Make is_bridge a bool
pcie: Simplify pci_adjust_config_limit()
acpi: pci: use build_append_foo() API to construct MCFG
hw/acpi: Consolidate build_mcfg to pci.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This makes use of qdev_prop_drive_iothread for scsi-disk so that the
disk can be attached to a node that is already in the target AioContext.
We need to check that the HBA actually supports iothreads, otherwise
scsi-disk must make sure that the node is already in the main
AioContext.
This changes the error message for conflicting iothread settings.
Previously, virtio-scsi produced the error message, now it comes from
blk_set_aio_context(). Update a test case accordingly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some qdev block devices have support for iothreads and take care of the
AioContext they are running in, but most devices don't know about any of
this. For the latter category, the qdev drive property must make sure
that their BlockBackend is in the main AioContext.
Unfortunately, while the current code just does the same thing for
devices that do support iothreads, this is not correct and it would show
as soon as we actually try to keep a consistent AioContext assignment
across all nodes and users of a block graph subtree: If a node is
already in a non-default AioContext because of one of its users,
attaching a new device should still be possible if that device can work
in the same AioContext. Switching the node back to the main context
first and only then into the device AioContext causes failure (because
the existing user wouldn't allow the switch to the main context).
So devices that support iothreads need a different kind of drive
property that leaves the node in its current AioContext, but by using
this type, the device promises to check later that it can work with this
context.
This patch adds the qdev infrastructure that allows devices to signal
that they handle iothreads and qdev should leave the AioContext alone.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit b2fc91db84 ("q35: set split kernel irqchip as default") changed
the default for the pc-q35-4.0 machine type to use split irqchip, which
turned out to have disasterous effects on vfio-pci INTx support. KVM
resampling irqfds are registered for handling these interrupts, but
these are non-functional in split irqchip mode. We can't simply test
for split irqchip in QEMU as userspace handling of this interrupt is a
significant performance regression versus KVM handling (GeForce GPUs
assigned to Windows VMs are non-functional without forcing MSI mode or
re-enabling kernel irqchip).
The resolution is to revert the change in default irqchip mode in the
pc-q35-4.1 machine and create a pc-q35-4.0.1 machine for the 4.0-stable
branch. The qemu-q35-4.0 machine type should not be used in vfio-pci
configurations for devices requiring legacy INTx support without
explicitly modifying the VM configuration to use kernel irqchip.
Link: https://bugs.launchpad.net/qemu/+bug/1826422
Fixes: b2fc91db84 ("q35: set split kernel irqchip as default")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <155786484688.13873.6037015630912983760.stgit@gimli.home>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to perform a valid migration of a vhost-scsi device,
the following requirements must be met:
(1) The virtio-scsi device state needs to be saved & loaded.
(2) The vhost backend must be stopped before virtio-scsi device state
is saved:
(2.1) Sync vhost backend state to virtio-scsi device state.
(2.2) No further I/O requests are made by vhost backend to target
SCSI device.
(2.3) No further guest memory access takes place after VM is stopped.
(3) Requests in-flight to target SCSI device are completed before
migration handover.
(4) Target SCSI device state needs to be saved & loaded into the
destination host target SCSI device.
Previous commit ("vhost-scsi: Add VMState descriptor")
add support to save & load the device state using VMState.
This meets requirement (1).
When VM is stopped by migration thread (On Pre-Copy complete), the
following code path is executed:
migration_completion() -> vm_stop_force_state() -> vm_stop() ->
do_vm_stop().
do_vm_stop() calls first pause_all_vcpus() which pause all guest
vCPUs and then call vm_state_notify().
In case of vhost-scsi device, this will lead to the following code path
to be executed:
vm_state_notify() -> virtio_vmstate_change() ->
virtio_set_status() -> vhost_scsi_set_status() -> vhost_scsi_stop().
vhost_scsi_stop() then calls vhost_scsi_clear_endpoint() and
vhost_scsi_common_stop().
vhost_scsi_clear_endpoint() sends VHOST_SCSI_CLEAR_ENDPOINT ioctl to
vhost backend which will reach kernel's vhost_scsi_clear_endpoint()
which process all pending I/O requests and wait for them to complete
(vhost_scsi_flush()). This meets requirement (3).
vhost_scsi_common_stop() will stop the vhost backend.
As part of this stop, dirty-bitmap is synced and vhost backend state is
synced with virtio-scsi device state. As at this point guest vCPUs are
already paused, this meets requirement (2).
At this point we are left with requirement (4) which is target SCSI
device specific and therefore cannot be done by QEMU. Which is the main
reason why vhost-scsi adds a migration blocker.
However, as this can be handled either by an external orchestrator or
by using shared-storage (i.e. iSCSI), there is no reason to limit the
orchestrator from being able to explictly specify it wish to enable
migration even when VM have a vhost-scsi device.
Considering all the above, this commit allows orchestrator to explictly
specify that it is responsbile for taking care of requirement (4) and
therefore vhost-scsi should not add a migration blocker.
Reviewed-by: Nir Weiner <nir.weiner@oracle.com>
Reviewed-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190416125912.44001-4-liran.alon@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
-----BEGIN PGP SIGNATURE-----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=2q3B
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190529' into staging
ppc patch queue 2019-05-29
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
# gpg: Signature made Wed 29 May 2019 07:49:04 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190529: (44 commits)
ppc/pnv: add dummy XSCOM registers for PRD initialization
ppc/pnv: introduce new skiboot platform properties
spapr: Don't migrate the hpt_maxpagesize cap to older machine types
spapr: change default interrupt mode to 'dual'
spapr/xive: fix multiple resets when using the 'dual' interrupt mode
docs: provide documentation on the POWER9 XIVE interrupt controller
spapr/irq: add KVM support to the 'dual' machine
ppc/xics: fix irq priority in ics_set_irq_type()
spapr/irq: initialize the IRQ device only once
spapr/irq: introduce a spapr_irq_init_device() helper
spapr: check for the activation of the KVM IRQ device
spapr: introduce routines to delete the KVM IRQ device
sysbus: add a sysbus_mmio_unmap() helper
spapr/xive: activate KVM support
spapr/xive: add migration support for KVM
spapr/xive: introduce a VM state change handler
spapr/xive: add state synchronization with KVM
spapr/xive: add hcall support when under KVM
spapr/xive: add KVM support
spapr: Print out extra hints when CAS negotiation of interrupt mode fails
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The is_bridge field in PCIDevice acts as a bool, but is declared as an int.
Declare it as a bool for clarity, and change everything that writes it to
use true/false instead of 0/1 to match.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190513061939.3464-5-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since c2077e2c "pci: Adjust PCI config limit based on bus topology",
pci_adjust_config_limit() has been used in the config space read and write
paths to only permit access to extended config space on buses which permit
it. Specifically it prevents access on devices below a vanilla-PCI bus via
some combination of bridges, even if both the host bridge and the device
itself are PCI-E.
It accomplishes this with a somewhat complex call up the chain of bridges
to see if any of them prohibit extended config space access. This is
overly complex, since we can always know if the bus will support such
access at the point it is constructed.
This patch simplifies the test by using a flag in the PCIBus instance
indicating whether extended configuration space is accessible. It is
false for vanilla PCI buses. For PCI-E buses, it is true for root
buses and equal to the parent bus's's capability otherwise.
For the special case of sPAPR's paravirtualized PCI root bus, which
acts mostly like vanilla PCI, but does allow extended config space
access, we override the default value of the flag from the host bridge
code.
This should cause no behavioural change.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190513061939.3464-4-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
build_append_foo() API doesn't need explicit endianness conversions
which eliminates a source of errors and it makes build_mcfg() look like
declarative definition of MCFG table in ACPI spec, which makes it easy
to review.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v3:
* add some comment on the Configuration Space base address allocation
structure
v2:
* miss the reserved[8] of MCFG in last version, add it back
* drop SOBs and make sure bios-tables-test all OK
Message-Id: <20190521062836.6541-3-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we have two identical build_mcfg functions.
Consolidate them in acpi/pci.c.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
v4:
* ACPI_PCI depends on both ACPI and PCI
* rebase on latest master, adjust arm Kconfig
v3:
* adjust changelog based on Igor's suggestion
Message-Id: <20190521062836.6541-2-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add new virtio-gpu devices with a "vhost-user" property. The
associated vhost-user backend is used to handle the virtio rings and
provide rendering results thanks to the vhost-user-gpu protocol.
Example usage:
-object vhost-user-backend,id=vug,cmd="./vhost-user-gpu"
-device vhost-user-vga,vhost-user=vug
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-10-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a base class that is common to virtio-gpu and vhost-user-gpu
devices.
The VirtIOGPUBase base class provides common functionalities necessary
for both virtio-gpu and vhost-user-gpu:
- common configuration (max-outputs, initial resolution, flags)
- virtio device initialization, including queue setup
- device pre-conditions checks (iommu)
- migration blocker
- virtio device callbacks
- hooking up to qemu display subsystem
- a few common helper functions to reset the device, retrieve display
informations
- a class callback to unblock the rendering (for GL updates)
What is left to the virtio-gpu subdevice to take care of, in short,
are all the virtio queues handling, command processing and migration.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-8-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This will allow to share the format conversion function with
vhost-user-gpu.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The helper functions are useful to build the vhost-user-gpu backend.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a new vhost-user message to give a unix socket to a vhost-user
backend for GPU display updates.
Back when I started that work, I added a new GPU channel because the
vhost-user protocol wasn't bidirectional. Since then, there is a
vhost-user-slave channel for the slave to send requests to the master.
We could extend it with GPU messages. However, the GPU protocol is
quite orthogonal to vhost-user, thus I chose to have a new dedicated
channel.
See vhost-user-gpu.rst for the protocol details.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-2-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 0b8c89be7f7b added the hpt_maxpagesize capability to the migration
stream. This is okay for new machine types but it breaks backward migration
to older QEMUs, which don't expect the extra subsection.
Add a compatibility boolean flag to the sPAPR machine class and use it to
skip migration of the capability for machine types 4.0 and older. This
fixes migration to an older QEMU. Note that the destination will emit a
warning:
qemu-system-ppc64: warning: cap-hpt-max-page-size lower level (16) in incoming stream than on destination (24)
This is expected and harmless though. It is okay to migrate from a lower
HPT maximum page size (64k) to a greater one (16M).
Fixes: 0b8c89be7f7b "spapr: Add forgotten capability to migration stream"
Based-on: <20190522074016.10521-3-clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155853262675.1158324.17301777846476373459.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt mode is chosen by the CAS negotiation process and
activated after a reset to take into account the required changes in
the machine. This brings new constraints on how the associated KVM IRQ
device is initialized.
Currently, each model takes care of the initialization of the KVM
device in their realize method but this is not possible anymore as the
initialization needs to be done globaly when the interrupt mode is
known, i.e. when machine is reseted. It also means that we need a way
to delete a KVM device when another mode is chosen.
Also, to support migration, the QEMU objects holding the state to
transfer should always be available but not necessarily activated.
The overall approach of this proposal is to initialize both interrupt
mode at the QEMU level to keep the IRQ number space in sync and to
allow switching from one mode to another. For the KVM side of things,
the whole initialization of the KVM device, sources and presenters, is
grouped in a single routine. The XICS and XIVE sPAPR IRQ reset
handlers are modified accordingly to handle the init and the delete
sequences of the KVM device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a check to make sure that the routine initializing the emulated
IRQ device is called once. We don't have much to test on the XICS
side, so we introduce a 'init' boolean under ICSState.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The way the XICS and the XIVE devices are initialized follows the same
pattern. First, try to connect to the KVM device and if not possible
fallback on the emulated device, unless a kernel_irqchip is required.
The spapr_irq_init_device() routine implements this sequence in
generic way using new sPAPR IRQ handlers ->init_emu() and ->init_kvm().
The XIVE init sequence is moved under the associated sPAPR IRQ
->init() handler. This will change again when KVM support is added for
the dual interrupt mode.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If a new interrupt mode is chosen by CAS, the machine generates a
reset to reconfigure. At this point, the connection with the previous
KVM device needs to be closed and a new connection needs to opened
with the KVM device operating the chosen interrupt mode.
New routines are introduced to destroy the XICS and the XIVE KVM
devices. They make use of a new KVM device ioctl which destroys the
device and also disconnects the IRQ presenters from the vCPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used to remove the MMIO regions of the POWER9 XIVE
interrupt controller when the sPAPR machine is reseted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the VM is stopped, the VM state handler stabilizes the XIVE IC
and marks the EQ pages dirty. These are then transferred to destination
before the transfer of the device vmstates starts.
The SpaprXive interrupt controller model captures the XIVE internal
tables, EAT and ENDT and the XiveTCTX model does the same for the
thread interrupt context registers.
At restart, the SpaprXive 'post_load' method restores all the XIVE
states. It is called by the sPAPR machine 'post_load' method, when all
XIVE states have been transferred and loaded.
Finally, the source states are restored in the VM change state handler
when the machine reaches the running state.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This handler is in charge of stabilizing the flow of event notifications
in the XIVE controller before migrating a guest. This is a requirement
before transferring the guest EQ pages to a destination.
When the VM is stopped, the handler sets the source PQs to PENDING to
stop the flow of events and to possibly catch a triggered interrupt
occuring while the VM is stopped. Their previous state is saved. The
XIVE controller is then synced through KVM to flush any in-flight
event notification and to stabilize the EQs. At this stage, the EQ
pages are marked dirty to make sure the EQ pages are transferred if a
migration sequence is in progress.
The previous configuration of the sources is restored when the VM
resumes, after a migration or a stop. If an interrupt was queued while
the VM was stopped, the handler simply generates the missing trigger.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This extends the KVM XIVE device backend with 'synchronize_state'
methods used to retrieve the state from KVM. The HW state of the
sources, the KVM device and the thread interrupt contexts are
collected for the monitor usage and also migration.
These get operations rely on their KVM counterpart in the host kernel
which acts as a proxy for OPAL, the host firmware. The set operations
will be added for migration support later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
XIVE hcalls are all redirected to QEMU as none are on a fast path.
When necessary, QEMU invokes KVM through specific ioctls to perform
host operations. QEMU should have done the necessary checks before
calling KVM and, in case of failure, H_HARDWARE is simply returned.
H_INT_ESB is a special case that could have been handled under KVM
but the impact on performance was low when under QEMU. Here are some
figures :
kernel irqchip OFF ON
H_INT_ESB KVM QEMU
rtl8139 (LSI ) 1.19 1.24 1.23 Gbits/sec
virtio 31.80 42.30 -- Gbits/sec
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This introduces a set of helpers when KVM is in use, which create the
KVM XIVE device, initialize the interrupt sources at a KVM level and
connect the interrupt presenters to the vCPU.
They also handle the initialization of the TIMA and the source ESB
memory regions of the controller. These have a different type under
KVM. They are 'ram device' memory mappings, similarly to VFIO, exposed
to the guest and the associated VMAs on the host are populated
dynamically with the appropriate pages using a fault handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr machine capabilities are supposed to be sent in the migration stream
so that we can sanity check the source and destination have compatible
configuration. Unfortunately, when we added the hpt-max-page-size
capability, we forgot to add it to the migration state. This means that we
can generate spurious warnings when both ends are configured for large
pages, or potentially fail to warn if the source is configured for huge
pages, but the destination is not.
Fixes: 2309832afd "spapr: Maximum (HPT) pagesize property"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The high order bits of the address of the OS event queue is stored in
bits [4-31] of word2 of the XIVE END internal structures and the low
order bits in word3. This structure is using Big Endian ordering and
computing the value requires some simple arithmetic which happens to
be wrong. The mask removing bits [0-3] of word2 is applied to the
wrong value and the resulting address is bogus when above 64GB.
Guests with more than 64GB of RAM will allocate pages for the OS event
queues which will reside above the 64GB limit. In this case, the XIVE
device model will wake up the CPUs in case of a notification, such as
IPIs, but the update of the event queue will be written at the wrong
place in memory. The result is uncertain as the guest memory is
trashed and IPI are not delivered.
Introduce a helper xive_end_qaddr() to compute this value correctly in
all places where it is used.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190508171946.657-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- semihosting re-factor (used in system tests)
- aarch64 and alpha system tests
- editorconfig tweak for .S
- some docker image updates
- iotests clean-up (without make check inclusion)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAlztYToACgkQ+9DbCVqe
KkQU9wf/Uv5qBgDn9MwcCt8tzHTX/i21QHwFLBbCmFoUwZjSridZ2KV6Ma3ig4mF
xY+8Cr5oZT186V+aD39K6KCZKqZRulIpRVNkOKXEfAAklUoAyQs95Wa8F8LtO1eG
vOtOYEdkXQQiAnlnQ+eaGiZQ2mpbCbREa10JrBhxp6iXh0PYcvtD7iAlOldqIvd2
hDRwOgTtYoiiKh6UdediAgQsRvv6oNPHFUOjWgrGxfhPWKbjCVKl7VS4furg9zux
j/S0E0xYKhj+JNq3arjiMUMl19TauCBQLrbQpphd1jOl1s7bELRjAuaKM60TVIbW
Hd2/PYbGnkpyUcJQh0Pr1cb4RMcznw==
=lvtu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-next-280519-2' into staging
Various testing updates
- semihosting re-factor (used in system tests)
- aarch64 and alpha system tests
- editorconfig tweak for .S
- some docker image updates
- iotests clean-up (without make check inclusion)
# gpg: Signature made Tue 28 May 2019 17:26:34 BST
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-next-280519-2: (27 commits)
tests/qemu-iotests: re-format output to for make check-block
tests/qemu-iotests/group: Re-use the "auto" group for tests that can always run
Makefile.target: support per-target coverage reports
Makefile: include per-target build directories in coverage report
Makefile: fix coverage-report reference to BUILD_DIR
.travis.yml: enable aarch64-softmmu and alpha-softmmu tcg tests
tests/tcg/alpha: add system boot.S
tests/tcg/multiarch: expand system memory test to cover more
tests/tcg/minilib: support %c format char
tests/tcg/multiarch: move the system memory test
tests/tcg/aarch64: add system boot.S
editorconfig: add settings for .s/.S files
tests/tcg/multiarch: add hello world system test
tests/tcg/multiarch: add support for multiarch system tests
tests/docker: Test more components on the Fedora default image
tests/docker: add ubuntu 18.04
MAINTAINERS: update for semihostings new home
target/mips: convert UHI_plog to use common semihosting code
target/mips: only build mips-semi for softmmu
target/arm: correct return values for WRITE/READ in arm-semi
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This tag contains a handful of patches that I'd like to target for 4.1:
* An emulation for SiFive's GPIO device.
* A fix to disallow sfence.vma from userspace.
* Additional decodetree cleanups that should have no functional impact.
* C extension emulation fidelity fixes that were noticed as part of that
cleanup process.
* A new "spike" target, along with the deprecation of a handful of old
targets and CPUs.
* Some initial infastructure related to the hypervisor extension.
* An emulation fidelity fix that prevents prevents arbitrary bits in the
SIP CSR from being set.
* A small performance improvement that avoids excessive TLB flushing
when the ASID does not change.
This time I've used a new testing workflow: I've tested on both 32-bit
and 64-bit builds of OpenEmbedded, via the default OpenSBI-based boot
flow.
-----BEGIN PGP SIGNATURE-----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=7LvI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.1-sf0' into staging
RISC-V Patches for the 4.1 Soft Freeze, Part 1
This tag contains a handful of patches that I'd like to target for 4.1:
* An emulation for SiFive's GPIO device.
* A fix to disallow sfence.vma from userspace.
* Additional decodetree cleanups that should have no functional impact.
* C extension emulation fidelity fixes that were noticed as part of that
cleanup process.
* A new "spike" target, along with the deprecation of a handful of old
targets and CPUs.
* Some initial infastructure related to the hypervisor extension.
* An emulation fidelity fix that prevents prevents arbitrary bits in the
SIP CSR from being set.
* A small performance improvement that avoids excessive TLB flushing
when the ASID does not change.
This time I've used a new testing workflow: I've tested on both 32-bit
and 64-bit builds of OpenEmbedded, via the default OpenSBI-based boot
flow.
# gpg: Signature made Sat 25 May 2019 01:05:57 BST
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.1-sf0: (29 commits)
target/riscv: Only flush TLB if SATP.ASID changes
target/riscv: More accurate handling of `sip` CSR
target/riscv: Add checks for several RVC reserved operands
target/riscv: Add the HGATP register masks
target/riscv: Add the HSTATUS register masks
target/riscv: Add Hypervisor CSR macros
target/riscv: Allow setting mstatus virtulisation bits
target/riscv: Add the MPV and MTL mstatus bits
target/riscv: Improve the scause logic
target/riscv: Trigger interrupt on MIP update asynchronously
target/riscv: Mark privilege level 2 as reserved
riscv: spike: Add a generic spike machine
target/riscv: Deprecate the generic no MMU CPUs
target/riscv: Add a base 32 and 64 bit CPU
target/riscv: Create settable CPU properties
riscv: virt: Allow specifying a CPU via commandline
linux-user/riscv: Add the CPU type as a comment
target/riscv: Remove unused include of riscv_htif.h for virt board riscv
target/riscv: Remove spaces from register names
target/riscv: Split gen_arith_imm into functional and temp
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It will be useful for a number of use-cases to be able to re-direct
output to a file like we do with serial output. This does the wiring
to allow us to treat then semihosting console like just another
character output device.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This provides two functions for handling console output that handle
the common backend behaviour for semihosting.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
In preparation for having some more common semihosting code let's
excise the current config magic from vl.c into its own file. We shall
later add more conditionals to the build configurations so we can
avoid building this if we don't need it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
At the same time deprecate the ISA string CPUs.
It is dobtful anyone specifies the CPUs, but we are keeping them for the
Spike machine (which is about to be depreated) so we may as well just
mark them as deprecated.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
QEMU model of the GPIO device on the SiFive E300 series SOCs.
The pins are not used by a board definition yet, however this
implementation can already be used to trigger GPIO interrupts from the
software by configuring a pin as both output and input.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
To be coherent with the other peripherals contained in the
BCM2835PeripheralState structure, directly allocate the PL011State
(instead of using the pl011 uart as a pointer to a SysBusDevice).
Initialize the PL011State with object_initialize() instead of
object_new().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-6-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
If xres / yres were specified in QEMU command line, write them as an initial
resolution to the fw-config space on guest reset, which a later BIOS / OVMF
patch can take advantage of.
Signed-off-by: HOU Qiming <hqm03ster@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-id: 20190513115731.17588-4-marcel.apfelbaum@gmail.com
[fixed malformed patch]
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190520214342.13709-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The header file hw/arm/arm.h now includes only declarations
relating to hw/arm/boot.c functionality. Rename it accordingly,
and adjust its header comment.
The bulk of this commit was created via
perl -pi -e 's|hw/arm/arm.h|hw/arm/boot.h|' hw/arm/*.c include/hw/arm/*.h
In a few cases we can just delete the #include:
hw/arm/msf2-soc.c, include/hw/arm/aspeed_soc.h and
include/hw/arm/bcm2836.h did not require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-4-peter.maydell@linaro.org
The system_clock_scale global is used only by the armv7m systick
device; move the extern declaration to the armv7m_systick.h header,
and expand the comment to explain what it is and that it should
ideally be replaced with a different approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-2-peter.maydell@linaro.org
Add fw_cfg_arch_key_name() which returns the name of
an architecture-specific key.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190422195020.1494-3-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
'MSIX_CAP_LENGTH' is defined in two .c file. Move it
to hw/pci/msix.h file to reduce duplicated code.
CC: qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190521151543.92274-5-liq3ea@163.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
- have the bios tolerate bootmap signature entries
- next chunk of vector instruction support in tcg
- a headers update against Linux 5.2-rc1
- add more facilities and gen15 machines to the cpu model
-----BEGIN PGP SIGNATURE-----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=+HXM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20190521-3' into staging
s390x update:
- have the bios tolerate bootmap signature entries
- next chunk of vector instruction support in tcg
- a headers update against Linux 5.2-rc1
- add more facilities and gen15 machines to the cpu model
# gpg: Signature made Tue 21 May 2019 16:09:35 BST
# gpg: using RSA key C3D0D66DC3624FF6A8C018CEDECF6B93C6F02FAF
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20190521-3: (55 commits)
s390x/cpumodel: wire up 8561 and 8562 as gen15 machines
s390x/cpumodel: add gen15 defintions
s390x/cpumodel: add Deflate-conversion facility
s390x/cpumodel: enhanced sort facility
s390x/cpumodel: vector enhancements
s390x/cpumodel: msa9 facility
s390x/cpumodel: Miscellaneous-Instruction-Extensions Facility 3
s390x/cpumodel: ignore csske for expansion
linux headers: update against Linux 5.2-rc1
update-linux-headers: handle new header file
s390x/tcg: Implement VECTOR TEST UNDER MASK
s390x/tcg: Implement VECTOR SUM ACROSS WORD
s390x/tcg: Implement VECTOR SUM ACROSS QUADWORD
s390x/tcg: Implement VECTOR SUM ACROSS DOUBLEWORD
s390x/tcg: Implement VECTOR SUBTRACT WITH BORROW COMPUTE BORROW INDICATION
s390x/tcg: Implement VECTOR SUBTRACT WITH BORROW INDICATION
s390x/tcg: Implement VECTOR SUBTRACT COMPUTE BORROW INDICATION
s390x/tcg: Implement VECTOR SUBTRACT
s390x/tcg: Implement VECTOR SHIFT RIGHT LOGICAL *
s390x/tcg: Implement VECTOR SHIFT RIGHT ARITHMETIC
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pci_bus_is_root() currently relies on a method in the PCIBusClass.
But it's always known if a PCI bus is a root bus when we create it, so
using a dynamic method is overkill.
This replaces it with an IS_ROOT bit in a new flags field, which is set on
root buses and otherwise clear. As a bonus this removes the special
is_root logic from pci_expander_bridge, since it already creates its bus
as a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190424041959.4087-3-david@gibson.dropbear.id.au>
To build MCFG, two information is necessary:
* bus number
* base address
Abstract these two information to AcpiMcfgInfo so that build_mcfg and
build_mcfg_q35 will have the same declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190419003053.8260-5-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since we now support the message VHOST_USER_GET_INFLIGHT_FD
and VHOST_USER_SET_INFLIGHT_FD. The backend is able to restart
safely because it can track inflight I/O in shared memory.
This patch allows qemu to reconnect the backend after
connection closed.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Ni Xun <nixun@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190320112646.3712-7-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio 1.0 transitional devices support driver uses the device
before setting the DRIVER_OK status bit. So we introduce a started
flag to indicate whether driver has started the device or not.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190320112646.3712-2-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit d7741743f4.
Relying on setting properties on parents types which may not
be relevant to certain sub-classes had unexpected side-effects
causing bugs in device config defaults. It is preferrable to
be explicit about which devices get which properties, even if
this needs repetition.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190215103239.28640-3-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3rY3AAoJEL/70l94x66D91kH/21LLnL+sKmyueSM/Sek4id2
r06tHdGMdl5Od3I5uMD9gnr4AriiCZc9ybQDQ1N879wKMmQPZwcnf2GJ5DZ0wa3L
jHoQO07Bg0KZGWALjXiN5PWB0DlJtXsTm0C4q4tnt6V/ueasjxouBk9/fRLRc09n
QTS379X9QvPElFTv3WPfGz6kmkLq8VMmdRnSlXneB9xTyXXJbFj3zlvDCElNSgWh
fZ7gnfYWB1LOC19HJxp1mJSkAUD5AgImYEK1Hmnr+BMs2sg6gypYNtp3LtE5FzmZ
HSdXYFyPkQV9UyTiV1XBs3bXJbGYj5OApfXCtwo/I2JtP+LhHBA2eq1Gs3QgP98=
=zSSj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Mostly bugfixes and cleanups, the most important being
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
# gpg: Signature made Fri 17 May 2019 14:25:11 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (21 commits)
hw/net/ne2000: Extract the PCI device from the chipset common code
hw/char: Move multi-serial devices into separate file
ioapic: allow buggy guests mishandling level-triggered interrupts to make progress
build: don't build hardware objects with linux-user
build: chardev is only needed for softmmu targets
configure: qemu-ga is only needed with softmmu targets
build: replace GENERATED_FILES by generated-files-y
trace: only include trace-event-subdirs when they are needed
sun4m: obey -vga none
mips-fulong2e: obey -vga none
hw/i386/acpi: Assert a pointer is not null BEFORE using it
hw/i386/acpi: Add object_resolve_type_unambiguous to improve modularity
hw/acpi/piix4: Move TYPE_PIIX4_PM to a public header
memory: correct the comment to DIRTY_MEMORY_MIGRATION
vl: fix -sandbox parsing crash when seccomp support is disabled
hvf: Add missing break statement
megasas: fix mapped frame size
vl: Add missing descriptions to the VGA adapters list
Declare -realtime as deprecated
roms: assert if max rom size is less than the used size
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAlzef04eHG1hcmsuY2F2
ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIfsIcIAJYsAv59etzYmqCA
rGvoma0FypA3SO2+zeqqH8r0b/gaO7b56aXxTIAVhPvf3mskwQ+ffVsxRZ+zIflj
CCo/PM4OBhqiOvK0qbbOxB0MmrrfGxMKrkUq0tuUubRH3T9fE5TSN3m3ObAHxgvq
wZFYmeOmlAOhqyqAWARP0xVPNRNcWTVdThSA6viW1FedWsxtMV/Om4bXmidTY7nm
CKAMdndqqYAgE9oVgFzfd46db4AGWKKIcTS+mrm8Y61hB1YuG7r+Bgu9qFcnjgcV
AHeGbRDZ0LY0jsAXZkAbRpYyCOsuYW6+yaDKt9h6meLJ7jpzonw4lARFFJtb9a/4
Kt6RBm0=
=UzYZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mcayland/tags/qemu-sparc-20190517' into staging
qemu-sparc queue
# gpg: Signature made Fri 17 May 2019 10:30:54 BST
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* remotes/mcayland/tags/qemu-sparc-20190517:
MAINTAINERS: add myself for leon3
leon3: introduce the plug and play mechanism
leon3: add a little bootloader
grlib, apbuart: get rid of the old-style create function
grlib, gptimer: get rid of the old-style create function
grlib, irqmp: get rid of the old-style create function
leon3: fix the error message when no bios are provided
hw/char/escc: Lower irq when transmit buffer is filled
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It was found that Hyper-V 2016 on KVM in some configurations (q35 machine +
piix4-usb-uhci) hangs on boot. Root-cause was that one of Hyper-V
level-triggered interrupt handler performs EOI before fixing the cause of
the interrupt. This results in IOAPIC keep re-raising the level-triggered
interrupt after EOI because irq-line remains asserted.
Gory details: https://www.spinics.net/lists/kvm/msg184484.html
(the whole thread).
Turns out we were dealing with similar issues before; in-kernel IOAPIC
implementation has commit 184564efae4d ("kvm: ioapic: conditionally delay
irq delivery duringeoi broadcast") which describes a very similar issue.
Steal the idea from the above mentioned commit for IOAPIC implementation in
QEMU. SUCCESSIVE_IRQ_MAX_COUNT, delay and the comment are borrowed as well.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190402080215.10747-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When building with CONFIG_Q35=n, we get:
LINK x86_64-softmmu/qemu-system-x86_64
/usr/bin/ld: hw/i386/acpi-build.o: in function `acpi_get_misc_info':
/source/qemu/hw/i386/acpi-build.c:243: undefined reference to `ich9_lpc_find'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:204: qemu-system-x86_64] Error 1
This is due to a dependency in acpi-build.c on the ICH9_LPC
(via ich9_lpc_find) and PIIX4_PM (via piix4_pm_find) devices.
To allow better modularity (compile acpi-build.c with only
Q35/ICH9 or ISAPC/PIIX4), refactor the similar helper as
object_resolve_type_unambiguous(). This way we relax the
linker dependencies and can build the x86 targets with a
selection of machines (instead of all of them).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190427144025.22880-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the TYPE_PIIX4_PM definition to the corresponding header,
so other files can use it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190427144025.22880-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We used to set backend unconditionally, this won't work for some
guests (e.g windows driver) who may not initialize all virtqueues. For
kernel backend, this will fail since it may try to validate the rings
during setting backend.
Fixing this by simply skipping the backend set when we find desc is
not ready.
Reviewed-by: Michael S. Tsirkin<mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds the AHB and APB plug and play devices.
They are scanned during the linux boot to discover the various peripheral.
Reviewed-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
If a ccw has CCW_FLAG_SKIP set, and the command is of type
read, read backwards, or sense, no data should be written
to the guest for that command.
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20190516133327.11430-1-cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Cleaned up with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-9-armbru@redhat.com>
We commonly define the header guard symbol without an explicit value.
Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-8-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Changes to slirp/ dropped, as we're about to spin it off]
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
slirp/src/*
target/s390x/gen-features.c
tests/fp/platform.h
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
tests/uefi-test-tools/UefiTestToolsPkg/BiosTablesTest/BiosTablesTest.c
We're in the process of spinning out slirp/. tests/fp/platform.h is
has to include qemu/osdep.h because tests/fp/berkeley-softfloat-3/ and
tests/fp/berkeley-testfloat-3/ don't. tests/uefi-test-tools/ is guest
software. The remaining reverts are the same as in commit
b7d89466dd.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190313162812.8885-1-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Revert change to tests/fp/platform.h, adjust commit message]
Add a new virtio-input device, which connects to a vhost-user
backend.
Instead of reading configuration directly from an input device /
evdev (like virtio-input-host), it reads it over vhost-user protocol
with {SET,GET}_CONFIG messages. The vhost-user-backend handles the
queues & events setup.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190503130034.24916-5-marcandre.lureau@redhat.com
[ kraxel: drop -{non-,}transitional variants ]
[ kraxel: fix "make check" on !linux ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* Stop using variable length array in dc_zva
* Implement M-profile XPSR GE bits
* Don't enable ARMV7M_EXCP_DEBUG from reset
* armv7m_nvic: NS BFAR and BFSR are RAZ/WI if BFHFNMINS == 0
* armv7m_nvic: Check subpriority in nvic_recompute_state_secure()
* fix various minor issues to allow building for Windows-on-ARM64
* aspeed: Set SDRAM size
* Allow system registers for KVM guests to be changed by QEMU code
* raspi: Diagnose requests for too much RAM
* virt: Support firmware configuration with -blockdev
-----BEGIN PGP SIGNATURE-----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=hcal
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190507' into staging
target-arm queue:
* Stop using variable length array in dc_zva
* Implement M-profile XPSR GE bits
* Don't enable ARMV7M_EXCP_DEBUG from reset
* armv7m_nvic: NS BFAR and BFSR are RAZ/WI if BFHFNMINS == 0
* armv7m_nvic: Check subpriority in nvic_recompute_state_secure()
* fix various minor issues to allow building for Windows-on-ARM64
* aspeed: Set SDRAM size
* Allow system registers for KVM guests to be changed by QEMU code
* raspi: Diagnose requests for too much RAM
* virt: Support firmware configuration with -blockdev
# gpg: Signature made Tue 07 May 2019 12:59:30 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190507:
target/arm: Stop using variable length array in dc_zva
target/arm: Implement XPSR GE bits
hw/intc/armv7m_nvic: Don't enable ARMV7M_EXCP_DEBUG from reset
hw/intc/armv7m_nvic: NS BFAR and BFSR are RAZ/WI if BFHFNMINS == 0
hw/arm/armv7m_nvic: Check subpriority in nvic_recompute_state_secure()
osdep: Fix mingw compilation regarding stdio formats
util/cacheinfo: Use uint64_t on LLP64 model to satisfy Windows ARM64
qga: Fix mingw compilation warnings on enum conversion
QEMU_PACKED: Remove gcc_struct attribute in Windows non x86 targets
arm: aspeed: Set SDRAM size
arm: Allow system registers for KVM guests to be changed by QEMU code
hw/arm/raspi: Diagnose requests for too much RAM
hw/arm/virt: Support firmware configuration with -blockdev
pflash_cfi01: New pflash_cfi01_legacy_drive()
pc: Rearrange pc_system_firmware_init()'s legacy -drive loop
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently use Qemu's default of 128MB. As we know how much ram each
machine ships with, make it easier on users by setting a default.
It can still be overridden with -m on the command line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190503022958.1394-1-joel@jms.id.au
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM virt machines put firmware in flash memory. To configure it,
you use -drive if=pflash,unit=0,... and optionally -drive
if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, we get two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
We recently solved this problem for x86 PC machines, in commit
ebc29e1bea. See the commit message for design rationale.
This commit solves it for ARM virt basically the same way: new machine
properties pflash0, pflash1 forward to the onboard flash devices'
properties. Requires creating the onboard devices in the
.instance_init() method virt_instance_init(). The existing code to
pick up drives defined with -drive if=pflash is replaced by code to
desugar into the machine properties.
There are a few behavioral differences, though:
* The flash devices are always present (x86: only present if
configured)
* Flash base addresses and sizes are fixed (x86: sizes depend on
images, mapped back to back below a fixed address)
* -bios configures contents of first pflash (x86: -bios configures ROM
contents)
* -bios is rejected when first pflash is also configured with -machine
pflash0=... (x86: bios is silently ignored then)
* -machine pflash1=... does not require -machine pflash0=... (x86: it
does).
The actual code is a bit simpler than for x86 mostly due to the first
two differences.
Before the patch, all the action is in create_flash(), called from the
machine's .init() method machvirt_init():
main()
machine_run_board_init()
machvirt_init()
create_flash()
create_one_flash() for flash[0]
create
configure
includes obeying -drive if=pflash,unit=0
realize
map
fall back to -bios
create_one_flash() for flash[1]
create
configure
includes obeying -drive if=pflash,unit=1
realize
map
update FDT
To make the machine properties work, we need to move device creation
to its .instance_init() method virt_instance_init().
Another complication is machvirt_init()'s computation of
@firmware_loaded: it predicts what create_flash() will do. Instead of
predicting what create_flash()'s replacement virt_firmware_init() will
do, I decided to have virt_firmware_init() return what it did.
Requires calling it a bit earlier.
Resulting call tree:
main()
current_machine = object_new()
...
virt_instance_init()
virt_flash_create()
virt_flash_create1() for flash[0]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash0 as alias for drive [NEW]
virt_flash_create1() for flash[1]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash1 as alias for drive [NEW]
for all machine props from the command line: machine_set_property()
...
property_set_alias() for machine props pflash0, pflash1
...
set_drive() for cfi.pflash01 prop drive
this is how -machine pflash0=... etc set
machine_run_board_init(current_machine);
virt_firmware_init()
pflash_cfi01_legacy_drive()
legacy -drive if=pflash,unit=0 and =1 [NEW]
virt_flash_map()
virt_flash_map1() for flash[0]
configure: num-blocks
realize
map
virt_flash_map1() for flash[1]
configure: num-blocks
realize
map
fall back to -bios
virt_flash_fdt()
update FDT
You have László to thank for making me explain this in detail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20190416091348.26075-4-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Factored out of pc_system_firmware_init() so the next commit can reuse
it in hw/arm/virt.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190416091348.26075-3-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move it together with the other EDID code. hw/i2c should only
include the core and the adapters, not the slaves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190325155923.30987-1-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This commit finally deletes "hw/devices.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-13-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-12-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-11-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-10-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since uWireSlave is only used in this new header, there is no
need to expose it via "qemu/typedefs.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-9-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-8-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-7-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an entries the Blizzard device in MAINTAINERS.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-6-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No code used the tc6393xb_gpio_in_get() and tc6393xb_gpio_out_set()
functions since their introduction in commit 88d2c950b0. Time to
remove them.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-4-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMMUNotifierNode struct is not necessary and brings extra
complexity so let's remove it. We now directly track the SMMUDevices
which have registered IOMMU MR notifiers.
This is inspired from the same transformation on intel-iommu
done in commit b4a4ba0d68
("intel-iommu: remove IntelIOMMUNotifierNode")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20190409160219.19026-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
-----BEGIN PGP SIGNATURE-----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=RpAK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190426' into staging
ppc patch queue 2019-04-26
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
# gpg: Signature made Fri 26 Apr 2019 07:02:19 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190426: (36 commits)
target/ppc: improve performance of large BAT invalidations
ppc/hash32: Rework R and C bit updates
ppc/hash64: Rework R and C bit updates
ppc/spapr: Use proper HPTE accessors for H_READ
target/ppc: Don't check UPRT in radix mode when in HV real mode
target/ppc/kvm: Convert DPRINTF to traces
target/ppc/trace-events: Fix trivial typo
spapr: Drop duplicate PCI swizzle code
spapr_pci: Get rid of duplicate code for node name creation
target/ppc: Style fixes for translate/spe-impl.inc.c
target/ppc: Style fixes for translate/vmx-impl.inc.c
target/ppc: Style fixes for translate/vsx-impl.inc.c
target/ppc: Style fixes for translate/fp-impl.inc.c
target/ppc: Style fixes for translate.c
target/ppc: Style fixes for translate_init.inc.c
target/ppc: Style fixes for monitor.c
target/ppc: Style fixes for mmu_helper.c
target/ppc: Style fixes for mmu-hash64.[ch]
target/ppc: Style fixes for mmu-hash32.[ch]
target/ppc: Style fixes for misc_helper.c
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With MT-TCG, we are now running translation in a racy way, thus
we need to mimic hardware when it comes to updating the R and
C bits, by doing byte stores.
The current "store_hpte" abstraction is ill suited for this, we
replace it with two separate callbacks for setting R and C.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190411080004.8690-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
LSI mapping in spapr currently open-codes standard PCI swizzling. It thus
duplicates the code of pci_swizzle_map_irq_fn().
Expose the swizzling formula so that it can be used with a slot number
when building the device tree. Simply drop pci_spapr_map_irq() and call
pci_swizzle_map_irq_fn() instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155448184841.8446.13959787238854054119.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Removing RTAS handlers will become necessary when the new pseries
machine supporting multiple interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190321144914.19934-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
NVIDIA V100 GPUs have on-board RAM which is mapped into the host memory
space and accessible as normal RAM via an NVLink bus. The VFIO-PCI driver
implements special regions for such GPUs and emulates an NVLink bridge.
NVLink2-enabled POWER9 CPUs also provide address translation services
which includes an ATS shootdown (ATSD) register exported via the NVLink
bridge device.
This adds a quirk to VFIO to map the GPU memory and create an MR;
the new MR is stored in a PCI device as a QOM link. The sPAPR PCI uses
this to get the MR and map it to the system address space.
Another quirk does the same for ATSD.
This adds additional steps to sPAPR PHB setup:
1. Search for specific GPUs and NPUs, collect findings in
sPAPRPHBState::nvgpus, manage system address space mappings;
2. Add device-specific properties such as "ibm,npu", "ibm,gpu",
"memory-block", "link-speed" to advertise the NVLink2 function to
the guest;
3. Add "mmio-atsd" to vPHB to advertise the ATSD capability;
4. Add new memory blocks (with extra "linux,memory-usable" to prevent
the guest OS from accessing the new memory until it is onlined) and
npuphb# nodes representing an NPU unit for every vPHB as the GPU driver
uses it for link discovery.
This allocates space for GPU RAM and ATSD like we do for MMIOs by
adding 2 new parameters to the phb_placement() hook. Older machine types
set these to zero.
This puts new memory nodes in a separate NUMA node to as the GPU RAM
needs to be configured equally distant from any other node in the system.
Unlike the host setup which assigns numa ids from 255 downwards, this
adds new NUMA nodes after the user configures nodes or from 1 if none
were configured.
This adds requirement similar to EEH - one IOMMU group per vPHB.
The reason for this is that ATSD registers belong to a physical NPU
so they cannot invalidate translations on GPUs attached to another NPU.
It is guaranteed by the host platform as it does not mix NVLink bridges
or GPUs from different NPU in the same IOMMU group. If more than one
IOMMU group is detected on a vPHB, this disables ATSD support for that
vPHB and prints a warning.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for vfio portions]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190312082103.130561-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Function find_default_machine() is introduced by commit 2c8cffa599
"vl: make find_default_machine externally visible", and it was used
outside of vl.c until commit a904410af5 "pc_sysfw: remove the rom_only
property".
Commit a904410af5 "pc_sysfw: remove the rom_only property" removed the
only user of find_default_machine() outside vl.c, but neglected to make
it static. Do that now.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190405064121.23662-2-richardw.yang@linux.intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add bootindex property and iplb data for vfio-ccw devices. This allows us to
forward boot information into the bios for vfio-ccw devices.
Refactor s390_get_ccw_device() to return device type. This prevents us from
having to use messy casting logic in several places.
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1554388475-18329-2-git-send-email-jjherne@linux.ibm.com>
[thuth: fixed "typedef struct VFIOCCWDevice" build failure with clang]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some PHB implementations, eg. PAPR used on pseries machine, act like
a regular PCI bus rather than a PCIe bus, but allow access to the
PCIe extended config space anyway.
Introduce a new PCI bus class method to modelize this behaviour and
use it when adjusting the config space size limit during accesses.
No behaviour change for existing PCI bus types.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155414130271.574858.4253514266378127489.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch fixes four different things, to maintain bisectability they
have been merged into a single patch. The following fixes are below:
sifive_plic: Fix incorrect irq calculation
The irq is incorrectly calculated to be off by one. It has worked in the
past as the priority_base offset has also been set incorrectly. We are
about to fix the priority_base offset so first first the irq
calculation.
sifive_u: Fix PLIC priority base offset and numbering
According to the FU540 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00. The same manual also specifies that the
PLIC only has 53 source priorities. Fix these two incorrect header
files.
We also need to over extend the plic_gpios[] array as the PLIC sources
count from 1 and not 0.
riscv: sifive_e: Fix PLIC priority base offset
According to the FE31 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00.
riscv: virt: Fix PLIC priority base offset
Update the virt offsets based on the newly updated SiFive U and SiFive E
offsets.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
VTD_RTADDR_RTT is dropped even by the VT-d spec, so QEMU should
probably do the same thing (after all we never really implemented it).
Since we've had a field for that in the migration stream, to keep
compatibility we need to fill the hole up.
Please refer to VT-d spec 10.4.6.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190329061422.7926-3-peterx@redhat.com>
Reviewed-by: Liu, Yi L <yi.l.liu@intel.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
27461d69a0 "ppc: add host-serial and host-model machine attributes
(CVE-2019-8934)" introduced 'host-serial' and 'host-model' machine
properties for spapr to explicitly control the values advertised to the
guest in device tree properties with the same names.
The previous behaviour on KVM was to unconditionally populate the device
tree with the real host serial number and model, which leaks possibly
sensitive information about the host to the guest.
To maintain compatibility for old machine types, we allowed those props
to be set to "passthrough" to take the value from the host as before. Or
they could be set to "none" to explicitly omit the device tree items.
Special casing specific values on what's otherwise a user supplied string
is very ugly. So, this patch simplifies things by implementing the
backwards compatibility in a different way: we have a machine class flag
set for the older machines, and we only load the host values into the
device tree if A) they're not set by the user and B) we have that flag set.
This does mean that the "passthrough" functionality is no longer available
with the current machine type. That's ok though: if a user or management
layer really wants the information passed through they can read it
themselves (OpenStack Nova already does something similar for x86).
It also means the user can't explicitly ask for the values to be omitted
on the old machine types. I think that's an acceptable trade-off: if you
care enough about not leaking the host information you can either move to
the new machine type, or use a dummy value for the properties.
For the new machine type, this also removes an odd inconsistency
between running on a POWER and non-POWER (or non-Linux) hosts: if the
host information couldn't be read from where we expect (in the host's
device tree as exposed by Linux), we'd fallback to omitting the guest
device tree items.
While we're there, improve some poorly worded comments, and the help text
for the properties.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
We reject undersized backends with a rather enigmatic "failed to read
the initial flash content" error. For instance:
$ qemu-system-ppc64 -S -display none -M sam460ex -drive if=pflash,format=raw,file=eins.img
qemu-system-ppc64: Initialization of device cfi.pflash02 failed: failed to read the initial flash content
We happily accept oversized images, ignoring their tail. Throwing
away parts of firmware that way is pretty much certain to end in an
even more enigmatic failure to boot.
Require the backend's size to match the device's size exactly. Report
mismatch like this:
qemu-system-ppc64: Initialization of device cfi.pflash01 failed: device requires 1048576 bytes, block backend provides 512 bytes
Improve the error for actual read failures to "can't read block
backend".
To avoid duplicating even more code between the two pflash device
models, do all that in new helper blk_check_size_and_read_all().
The error reporting can still be confusing. For instance:
qemu-system-ppc64 -S -display none -M taihu -drive if=pflash,format=raw,file=eins.img -drive if=pflash,unit=1,format=raw,file=zwei.img
qemu-system-ppc64: Initialization of device cfi.pflash02 failed: device requires 2097152 bytes, block backend provides 512 bytes
Leaves the user guessing which of the two -drive is wrong. Mention
the issue in a TODO comment.
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190319163551.32499-2-armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Previously we have per-device system memory aliases when DMAR is
disabled by the system. It will slow the system down if there are
lots of devices especially when DMAR is disabled, because each of the
aliased system address space will contain O(N) slots, and rendering
such N address spaces will be O(N^2) complexity.
This patch introduces a shared nodmar memory region and for each
device we only create an alias to the shared memory region. With the
aliasing, QEMU memory core API will be able to detect when devices are
sharing the same address space (which is the nodmar address space)
when rendering the FlatViews and the total number of FlatViews can be
dramatically reduced when there are a lot of devices.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190313094323.18263-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If renderer_blocked is set do not call virtio_gpu_virgl_reset().
Instead set a flag indicating that virglrenderer needs a reset.
When renderer_blocked gets cleared do the actual reset call.
Without this we can trigger an assert in spice due to calling
spice_qxl_gl_scanout() while another operation is still running:
spice_qxl_gl_scanout: condition `qxl_state->gl_draw_cookie == GL_DRAW_COOKIE_INVALID' failed
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190314115358.26678-2-kraxel@redhat.com
Allow interrogating device internals through HMP interface.
The exposed indicators can be used for troubleshooting by developers or
sysadmin.
There is no need to expose these attributes to a management system (e.x.
libvirt) because (1) most of them are not "device-management' related
info and (2) there is no guarantee the interface is stable.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1552300155-25216-6-git-send-email-yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
The BCM2836 control logic module includes a simple
"local timer" which is a programmable down-counter that
can generates an interrupt. Implement this functionality.
Signed-off-by: Zoltán Baldaszti <bztemail@gmail.com>
[PMM: wrote commit message; wrapped long line; tweaked
some comments to match the final version of the code]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently we do device realization like below:
hotplug_handler_pre_plug()
dc->realize()
hotplug_handler_plug()
Before we do device realization and plug, we should allocate necessary
resources and check if memory-hotplug-support property is enabled.
At the piix4 and ich9, the memory-hotplug-support property is checked at
plug stage. This means that device has been realized and mapped into guest
address space 'pc_dimm_plug()' by the time acpi plug handler is called,
where it might fail and crash QEMU due to reaching g_assert_not_reached()
(piix4) or error_abort (ich9).
Fix it by checking if memory hotplug is enabled at pre_plug stage
where we can gracefully abort hotplug request.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
CC: Igor Mammedov <imammedo@redhat.com>
CC: Eric Blake <eblake@redhat.com>
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190301033548.6691-1-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Claim ACS support in the generic PCIe root port to allow
passthrough of individual functions of a device to different
guests (in a nested virt.setting) with VFIO.
Without this patch, all functions of a device, such as all VFs of
an SR/IOV device, will end up in the same IOMMU group.
A similar situation occurs on Windows with Hyper-V.
In the single function device case, it also has a small cosmetic
benefit in that the root port itself is not grouped with
the device. VFIO handles that situation in that binding rules
only apply to endpoints, so it does not limit passthrough in
those cases.
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-Id: <319460b483f566dd57487eb3dd340ed4c10aa53c.1550768238.git-series.knut.omang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Implementing an ACS capability on downstream ports and multifunction
endpoints indicates isolation and IOMMU visibility to a finer
granularity. This creates smaller IOMMU groups in the guest and thus
more flexibility in assigning endpoints to guest userspace or an L2
guest.
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Message-Id: <07489975121696f5573b0a92baaf3486ef51e35d.1550768238.git-series.knut.omang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds support for vhost-user-blk device to get/set
inflight buffer from/to backend.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190228085355.9614-6-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces two new messages VHOST_USER_GET_INFLIGHT_FD
and VHOST_USER_SET_INFLIGHT_FD to support transferring a shared
buffer between qemu and backend.
Firstly, qemu uses VHOST_USER_GET_INFLIGHT_FD to get the
shared buffer from backend. Then qemu should send it back
through VHOST_USER_SET_INFLIGHT_FD each time we start vhost-user.
This shared buffer is used to track inflight I/O by backend.
Qemu should retrieve a new one when vm reset.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Chai Wen <chaiwen@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190228085355.9614-2-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds an option to provide flexibility for user to expose
Scalable Mode to guest. User could expose Scalable Mode to guest by
the config as below:
"-device intel-iommu,caching-mode=on,scalable-mode=on"
The Linux iommu driver has supported scalable mode. Please refer below
patch set:
https://www.spinics.net/lists/kernel/msg2985279.html
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <1551753295-30167-4-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per Intel(R) VT-d 3.0, the qi_desc is 256 bits in Scalable
Mode. This patch adds emulation of 256bits qi_desc.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
[Yi Sun is co-developer to rebase and refine the patch.]
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <1551753295-30167-3-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Intel(R) VT-d 3.0 spec introduces scalable mode address translation to
replace extended context mode. This patch extends current emulator to
support Scalable Mode which includes root table, context table and new
pasid table format change. Now intel_iommu emulates both legacy mode
and scalable mode (with legacy-equivalent capability set).
The key points are below:
1. Extend root table operations to support both legacy mode and scalable
mode.
2. Extend context table operations to support both legacy mode and
scalable mode.
3. Add pasid tabled operations to support scalable mode.
Signed-off-by: Liu, Yi L <yi.l.liu@intel.com>
[Yi Sun is co-developer to contribute much to refine the whole commit.]
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <1551753295-30167-2-git-send-email-yi.y.sun@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Take a VhostUserState* that can be pre-allocated, and initialize it
with the associated chardev.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
Message-Id: <20190308140454.32437-4-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This makes vfio_get_region_info_cap() to be used in quirks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190307050518.64968-3-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu coding standard is to use CamelCase for type and structure names,
and the pseries code follows that... sort of. There are quite a lot of
places where we bend the rules in order to preserve the capitalization of
internal acronyms like "PHB", "TCE", "DIMM" and most commonly "sPAPR".
That was a bad idea - it frequently leads to names ending up with hard to
read clusters of capital letters, and means they don't catch the eye as
type identifiers, which is kind of the point of the CamelCase convention in
the first place.
In short, keeping type identifiers look like CamelCase is more important
than preserving standard capitalization of internal "words". So, this
patch renames a heap of spapr internal type names to a more standard
CamelCase.
In addition to case changes, we also make some other identifier renames:
VIOsPAPR* -> SpaprVio*
The reverse word ordering was only ever used to mitigate the capital
cluster, so revert to the natural ordering.
VIOsPAPRVTYDevice -> SpaprVioVty
VIOsPAPRVLANDevice -> SpaprVioVlan
Brevity, since the "Device" didn't add useful information
sPAPRDRConnector -> SpaprDrc
sPAPRDRConnectorClass -> SpaprDrcClass
Brevity, and makes it clearer this is the same thing as a "DRC"
mentioned in many other places in the code
This is 100% a mechanical search-and-replace patch. It will, however,
conflict with essentially any and all outstanding patches touching the
spapr code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 processor does not support per-core frequency control. The
cores are arranged in groups of four, along with their respective L2
and L3 caches, into a structure known as a Quad. The frequency must be
managed at the Quad level.
Provide a basic Quad model to fake the settings done by the firmware
on the Non-Cacheable Unit (NCU). Each core pair (EX) needs a special
BAR setting for the TIMA area of XIVE because it resides on the same
address on all chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a new class attribute to define XSCOM operations per CPU
family and add a couple of XSCOM addresses controlling the power
management states of the core on POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC on POWER9 is very similar to the one found on POWER8. Provide
the same routines with P9 values for the registers and IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the OCC model for POWER9, provide a new
class attributes to define XSCOM operations per CPU family and a PSI
IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is just a simple reminder that SerIRQ routing should be
addressed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC Controller on POWER9 is very similar to the one found on
POWER8 but accesses are now done via on MMIOs, without the XSCOM and
ECCB logic. The device tree is populated differently so we add a
specific POWER9 routine for the purpose.
SerIRQ routing is yet to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ISA bus has a different DT nodename on POWER9. Compute the name
when the PnvChip is realized, that is before it is used by the machine
to populate the device tree with the ISA devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will ease the introduction of the LPC Controller model for POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PSI bridge on POWER9 is very similar to POWER8. The BAR is still
set through XSCOM but the controls are now entirely done with MMIOs.
More interrupts are defined and the interrupt controller interface has
changed to XIVE. The POWER9 model is a first example of the usage of
the notify() handler of the XiveNotifier interface, linking the PSI
XiveSource to its owning device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the PSI bridge model for POWER9, abstract
the POWER chip differences in a PnvPsi class model and introduce a
specific Pnv8Psi type for POWER8. POWER8 interface to the interrupt
controller is still XICS whereas POWER9 uses the new XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On sPAPR vfio_listener_region_add() is called in 2 situations:
1. a new listener is registered from vfio_connect_container();
2. a new IOMMU Memory Region is added from rtas_ibm_create_pe_dma_window().
In both cases vfio_listener_region_add() calls
memory_region_iommu_replay() to notify newly registered IOMMU notifiers
about existing mappings which is totally desirable for case 1.
However for case 2 it is nothing but noop as the window has just been
created and has no valid mappings so replaying those does not do anything.
It is barely noticeable with usual guests but if the window happens to be
really big, such no-op replay might take minutes and trigger RCU stall
warnings in the guest.
For example, a upcoming GPU RAM memory region mapped at 64TiB (right
after SPAPR_PCI_LIMIT) causes a 64bit DMA window to be at least 128TiB
which is (128<<40)/0x10000=2.147.483.648 TCEs to replay.
This mitigates the problem by adding an "skipping_replay" flag to
sPAPRTCETable and defining sPAPR own IOMMU MR replay() hook which does
exactly the same thing as the generic one except it returns early if
@skipping_replay==true.
Another way of fixing this would be delaying replay till the very first
H_PUT_TCE but this does not work if in-kernel H_PUT_TCE handler is
enabled (a likely case).
When "ibm,create-pe-dma-window" is complete, the guest will map only
required regions of the huge DMA window.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190307050518.64968-2-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have different interrupt controllers,
and reporting their state requires calling different helper routines.
However, the interrupt presenters are still handled in the higher
level pic_print_info() routine because they are not related to the
chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have a different set of devices and a
different device tree layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple model of the POWER9 XIVE interrupt controller for the
PowerNV machine which only addresses the needs of the skiboot
firmware. The PowerNV model reuses the common XIVE framework developed
for sPAPR as the fundamentals aspects are quite the same. The
difference are outlined below.
The controller initial BAR configuration is performed using the XSCOM
bus from there, MMIO are used for further configuration.
The MMIO regions exposed are :
- Interrupt controller registers
- ESB pages for IPIs and ENDs
- Presenter MMIO (Not used)
- Thread Interrupt Management Area MMIO, direct and indirect
The virtualization controller MMIO region containing the IPI ESB pages
and END ESB pages is sub-divided into "sets" which map portions of the
VC region to the different ESB pages. These are modeled with custom
address spaces and the XiveSource and XiveENDSource objects are sized
to the maximum allowed by HW. The memory regions are resized at
run-time using the configuration of EDT set translation table provided
by the firmware.
The XIVE virtualization structure tables (EAT, ENDT, NVTT) are now in
the machine RAM and not in the hypervisor anymore. The firmware
(skiboot) configures these tables using Virtual Structure Descriptor
defining the characteristics of each table : SBE, EAS, END and
NVT. These are later used to access the virtual interrupt entries. The
internal cache of these tables in the interrupt controller is updated
and invalidated using a set of registers.
Still to address to complete the model but not fully required is the
support for block grouping. Escalation support will be necessary for
KVM guests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 PowerNV machine will use a XIVE interrupt presenter type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine with need to encode the block id in the source
interrupt number before forwarding the source event notification to
the Router.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine can perform indirect loads and stores on the TIMA
on behalf of another CPU. Give the controller the possibility to call
the TIMA memory accessors with a XiveTCTX of its choice.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to get the CPU interrupt presenter in XIVE when the
TIMA is accessed from the indirect page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SPAPR_MEMORY_BLOCK_SIZE is logically a difference in memory addresses, and
hence of type hwaddr which is 64-bit. Previously it wasn't marked as such
which means that it could be treated as 32-bit. That will work in some
circumstances but if multiplied by another 32-bit value it could lead to
a 32-bit overflow and an incorrect result.
One specific instance of this in spapr_lmb_dt_populate() was spotted by
Coverity (CID 1399145).
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new spapr_cap SPAPR_CAP_CCF_ASSIST to be used to indicate
the requirement for a hw-assisted version of the count cache flush
workaround.
The count cache flush workaround is a software workaround which can be
used to flush the count cache on context switch. Some revisions of
hardware may have a hardware accelerated flush, in which case the
software flush can be shortened. This cap is used to set the
availability of such hardware acceleration for the count cache flush
routine.
The availability of such hardware acceleration is indicated by the
H_CPU_CHAR_BCCTR_FLUSH_ASSIST flag being set in the characteristics
returned from the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_cap SPAPR_CAP_IBS is used to indicate the level of capability
for mitigations for indirect branch speculation. Currently the available
values are broken (default), fixed-ibs (fixed by serialising indirect
branches) and fixed-ccd (fixed by diabling the count cache).
Introduce a new value for this capability denoted workaround, meaning that
software can work around the issue by flushing the count cache on
context switch. This option is available if the hypervisor sets the
H_CPU_BEHAV_FLUSH_COUNT_CACHE flag in the cpu behaviours returned from
the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add spapr_cap SPAPR_CAP_LARGE_DECREMENTER to be used to control the
availability of the large decrementer for a guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-1-sjitindarsingh@gmail.com>
[dwg: Trivial style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PC machines put firmware in ROM by default. To get it put into
flash memory (required by OVMF), you have to use -drive
if=pflash,unit=0,... and optionally -drive if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, it creates two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
Mapping -drive if=none,... to -blockdev is a solved problem. With
if=T other than if=none, -drive additionally configures a block device
frontend. For non-onboard devices, that part maps to -device. Also a
solved problem. For onboard devices such as PC flash memory, we have
an unsolved problem.
This is actually an instance of a wider problem: our general device
configuration interface doesn't cover onboard devices. Instead, we have
a zoo of ad hoc interfaces that are much more limited. One of them is
-drive, which we'd rather deprecate, but can't until we have suitable
replacements for all its uses.
Sadly, I can't attack the wider problem today. So back to the narrow
problem.
My first idea was to reduce it to its solved buddy by using pluggable
instead of onboard devices for the flash memory. Workable, but it
requires some extra smarts in firmware descriptors and libvirt. Paolo
had an idea that is simpler for libvirt: keep the devices onboard, and
add machine properties for their block backends.
The implementation is less than straightforward, I'm afraid.
First, block backend properties are *qdev* properties. Machines can't
have those, as they're not devices. I could duplicate these qdev
properties as QOM properties, but I hate that.
More seriously, the properties do not belong to the machine, they
belong to the onboard flash devices. Adding them to the machine would
then require bad magic to somehow transfer them to the flash devices.
Fortunately, QOM provides the means to handle exactly this case: add
alias properties to the machine that forward to the onboard devices'
properties.
Properties need to be created in .instance_init() methods. For PC
machines, that's pc_machine_initfn(). To make alias properties work,
we need to create the onboard flash devices there, too. Requires
several bug fixes, in the previous commits. We also have to realize
the devices. More on that below.
If the user sets pflash0, firmware resides in flash memory.
pc_system_firmware_init() maps and realizes the flash devices.
Else, firmware resides in ROM. The onboard flash devices aren't used
then. pc_system_firmware_init() destroys them unrealized, along with
the alias properties.
The existing code to pick up drives defined with -drive if=pflash is
replaced by code to desugar into the machine properties.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <87ftrtux81.fsf@dusky.pond.sub.org>
pc_system_firmware_init() parameter @isapc_ram_fw is PCMachineState
member pci_enabled negated. The next commit will need more of
PCMachineState. To prepare for that, pass a PCMachineState *, and
drop the now redundant parameter @isapc_ram_fw.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-11-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Add an helper to access the opaque struct PFlashCFI01.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190308131445.17502-9-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
See the previous commit for rationale.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308131445.17502-3-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Compatibility properties started life as a qdev property thing: we
supported them only for qdev properties, and implemented them with the
machinery backing command line option -global.
Recent commit fa0cb34d22 put them to use (tacitly) with memory
backend objects (subtypes of TYPE_MEMORY_BACKEND). To make that
possible, we first moved the work of applying them from the -global
machinery into TYPE_DEVICE's .instance_post_init() method
device_post_init(), in commits ea9ce8934c and b66bbee39f, then made
it available to TYPE_MEMORY_BACKEND's .instance_post_init() method
host_memory_backend_post_init() as object_apply_compat_props(), in
commit 1c3994f6d2.
Note the code smell: we now have function name starting with object_
in hw/core/qdev.c. It has to be there rather than in qom/, because it
calls qdev_get_machine() to find the current accelerator's and
machine's compat_props.
Turns out calling qdev_get_machine() there is problematic. If we
qdev_create() from a machine's .instance_init() method, we call
device_post_init() and thus qdev_get_machine() before main() can
create "/machine" in QOM. qdev_get_machine() tries to get it with
container_get(), which "helpfully" creates it as "container" object,
and returns that. object_apply_compat_props() tries to paper over the
problem by doing nothing when the value of qdev_get_machine() isn't a
TYPE_MACHINE. But the damage is done already: when main() later
attempts to create the real "/machine", it fails with "attempt to add
duplicate property 'machine' to object (type 'container')", and
aborts.
Since no machine .instance_init() calls qdev_create() so far, the bug
is latent. But since I want to do that, I get to fix the bug first.
Observe that object_apply_compat_props() doesn't actually need the
MachineState, only its the compat_props member of its MachineClass and
AccelClass. This permits a simple fix: register MachineClass and
AccelClass compat_props with the object_apply_compat_props() machinery
right after these classes get selected.
This is actually similar to how things worked before commits
ea9ce8934c and b66bbee39f, except we now register much earlier. The
old code registered them only after the machine's .instance_init()
ran, which would've broken compatibility properties for any devices
created there.
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190308131445.17502-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
We have two open-coded copies of macro PFLASH_CFI01(). Move the macro
to the header, so we can ditch the copies. Move PFLASH_CFI02() to the
header for symmetry.
We define macros TYPE_PFLASH_CFI01 and TYPE_PFLASH_CFI02 for type name
strings, then mostly use the strings. If the macros are worth
defining, they are worth using. Replace the strings by the macros.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-6-armbru@redhat.com>
pflash_cfi01.c and pflash_cfi02.c start their identifiers with
pflash_cfi01_ and pflash_cfi02_ respectively, except for
CFI_PFLASH01(), TYPE_CFI_PFLASH01, CFI_PFLASH02(), TYPE_CFI_PFLASH02.
Rename for consistency.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-5-armbru@redhat.com>
flash.h's incomplete struct pflash_t is completed both in
pflash_cfi01.c and in pflash_cfi02.c. The complete types are
incompatible. This can hide type errors, such as passing a pflash_t
created with pflash_cfi02_register() to pflash_cfi01_get_memory().
Furthermore, POSIX reserves typedef names ending with _t.
Rename the two structs to PFlashCFI01 and PFlashCFI02.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-2-armbru@redhat.com>
Kick the display link up event with a 0.1 sec delay,
so the guest has a chance to notice the link down first.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[update for redefined macro]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds EDID support to the vfio display (aka vgpu) code.
When supported by the mdev driver qemu will generate a EDID blob
and pass it on using the new vfio edid region. The EDID blob will
be updated on UI changes (i.e. window resize), so the guest can
adapt.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
[remove control flow via macro, use unsigned format specifier]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
As NVDIMM support is looming for ARM and SPAPR, let's
move the acpi_nvdimm_state to the generic machine struct
instead of duplicating the same code in several machines.
It is also renamed into nvdimms_state and becomes a pointer.
nvdimm and nvdimm-persistence become generic machine options.
They become guarded by a nvdimm_supported machine class member.
We also add a description for those options.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190308182053.5487-3-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As we intend to migrate the acpi_nvdimm_state into
the base machine with a new dimms_state name, let's
also rename the datatype.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308182053.5487-2-eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20190307080244.9011-4-kraxel@redhat.com
Introduced in 64b40bc54a, this definition is no more used since
a0b753dfd3. Remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Let's use a wrapper instead of looking it up manually. This function can
than be reused when we explicitly want to have the bus hotplug handler
(e.g. when the bus hotplug handler was overwritten by the machine
hotplug handler).
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-4-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will allow to return another hotplug handler than the default
one for a specific bus based device type. Which is needed to handle
non trivial plug/unplug sequences that need the access to resources
configured outside of bus where device is attached.
That will allow for returned hotplug handler to orchestrate wiring
in arbitrary order, by chaining other hotplug handlers when
it's needed.
PS:
It could be used for hybrid virtio-mem and virtio-pmem devices
where it will return machine as hotplug handler which will do
necessary wiring at machine level and then pass control down
the chain to bus specific hotplug handler.
Example of top level hotplug handler override and custom plug sequence:
some_machine_get_hotplug_handler(machine){
if (object_dynamic_cast(OBJECT(dev), TYPE_SOME_BUS_DEVICE)) {
return HOTPLUG_HANDLER(machine);
}
return NULL;
}
some_machine_device_plug(hotplug_dev, dev) {
if (object_dynamic_cast(OBJECT(dev), TYPE_SOME_BUS_DEVICE)) {
/* do machine specific initialization */
some_machine_init_special_device(dev)
/* pass control to bus specific handler */
hotplug_handler_plug(dev->parent_bus->hotplug_handler, dev)
}
}
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-3-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The qbus_is_full(BusState *bus) function (qdev_monitor.c) compares the max_index
value of the BusState structure with the max_dev value of the BusClass structure
to determine whether the maximum number of children has been reached for the
bus. The problem is, the max_index field of the BusState structure does not
necessarily reflect the number of devices that have been plugged into
the bus.
Whenever a child device is plugged into the bus, the bus's max_index value is
assigned to the child device and then incremented. If the child is subsequently
unplugged, the value of the max_index does not change and no longer reflects the
number of children.
When the bus's max_index value reaches the maximum number of devices
allowed for the bus (i.e., the max_dev field in the BusClass structure),
attempts to plug another device will be rejected claiming that the bus is
full -- even if the bus is actually empty.
To resolve the problem, a new 'num_children' field is being added to the
BusState structure to keep track of the number of children plugged into the
bus. It will be incremented when a child is plugged, and decremented when a
child is unplugged.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Pierre Morel<pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <1545062250-7573-1-git-send-email-akrowiak@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
(This replaces the pull sent yesterday)
a) 4 small fixes including the cancel problem
that caused the ahci migration test to fail
intermittently
b) Yury's ignore-shared feature
c) Juan's extra tests
d) Wei Wang's free page hinting
e) Some Colo fixes from Zhang Chen
Diff from yesterdays pull:
1) A missing fix of mine (cleanup during exit)
2) Changes from Eric/Markus on 'Create socket-address parameter'
-----BEGIN PGP SIGNATURE-----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=dk89
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20190306a' into staging
Migation pull 2019-03-06
(This replaces the pull sent yesterday)
a) 4 small fixes including the cancel problem
that caused the ahci migration test to fail
intermittently
b) Yury's ignore-shared feature
c) Juan's extra tests
d) Wei Wang's free page hinting
e) Some Colo fixes from Zhang Chen
Diff from yesterdays pull:
1) A missing fix of mine (cleanup during exit)
2) Changes from Eric/Markus on 'Create socket-address parameter'
# gpg: Signature made Wed 06 Mar 2019 11:39:53 GMT
# gpg: using RSA key 0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20190306a: (22 commits)
qapi/migration.json: Remove a variable that doesn't exist in example
Migration/colo.c: Make COLO node running after failover
Migration/colo.c: Fix double close bug when occur COLO failover
virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT
migration/ram.c: add the free page optimization enable flag
migration/ram.c: add a notifier chain for precopy
migration: API to clear bits of guest free pages from the dirty bitmap
migration: use bitmap_mutex in migration_bitmap_clear_dirty
bitmap: bitmap_count_one_with_offset
bitmap: fix bitmap_count_one
tests: Add basic migration precopy tcp test
migration: Create socket-address parameter
tests: Add migration xbzrle test
migration: Add capabilities validation
tests/migration-test: Add a test for ignore-shared capability
migration: Add an ability to ignore shared RAM blocks
migration: Introduce ignore-shared capability
exec: Change RAMBlockIterFunc definition
migration/rdma: clang compilation fix
migration: Cleanup during exit
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new feature enables the virtio-balloon device to receive hints of
guest free pages from the free page vq.
A notifier is registered to the migration precopy notifier chain. The
notifier calls free_page_start after the migration thread syncs the dirty
bitmap, so that the free page optimization starts to clear bits of free
pages from the bitmap. It calls the free_page_stop before the migration
thread syncs the bitmap, which is the end of the current round of ram
save. The free_page_stop is also called to stop the optimization in the
case when there is an error occurred in the process of ram saving.
Note: balloon will report pages which were free at the time of this call.
As the reporting happens asynchronously, dirty bit logging must be
enabled before this free_page_start call is made. Guest reporting must be
disabled before the migration dirty bitmap is synchronized.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Dr. David Alan Gilbert <dgilbert@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: Peter Xu <peterx@redhat.com>
Message-Id: <1544516693-5395-8-git-send-email-wei.w.wang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Dropped kernel header update, fixed up CMD_ID_* name change
Function acpi_table_add_builtin() is not used anymore.
Remove the definition and declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190214084939.20640-3-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Function pc_acpi_init() is not used anymore.
Remove the definition and declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190214084939.20640-2-richardw.yang@linux.intel.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Implement the watchdog timer for the stellaris boards.
This device is a close variant of the CMSDK APB watchdog
device, so we can model it by subclassing that device and
tweaking the behaviour of some of its registers.
Signed-off-by: Michel Heily <michelheily@gmail.com>
Reviewed-by: Peter Maydell <petser.maydell@linaro.org>
[PMM: rewrote commit message, fixed a few checkpatch nits,
added comment giving the URL of the spec for the Stellaris
variant of the watchdog device]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now the memory map has been static and the high IO region
base has always been 256GiB.
This patch modifies the virt_set_memmap() function, which freezes
the memory map, so that the high IO range base becomes floating,
located after the initial RAM and the device memory.
The function computes
- the base of the device memory,
- the size of the device memory,
- the high IO region base
- the highest GPA used in the memory map.
Entries of the high IO region are assigned a base address. The
device memory is initialized.
The highest GPA used in the memory map will be used at VM creation
to choose the requested IPA size.
Setting all the existing highmem IO regions beyond the RAM
allows to have a single contiguous RAM region (initial RAM and
possible hotpluggable device memory). That way we do not need
to do invasive changes in the EDK2 FW to support a dynamic
RAM base.
Still the user cannot request an initial RAM size greater than 255GB.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On ARM, the kvm_type will be resolved by querying the KVMState.
Let's add the MachineState handle to the callback so that we
can retrieve the KVMState handle. in kvm_init, when the callback
is called, the kvm_state variable is not yet set.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-5-eric.auger@redhat.com
[ppc parts]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the prospect to introduce an extended memory map supporting more
RAM, let's split the memory map array into two parts:
- the former a15memmap, renamed base_memmap, contains regions below
and including the RAM. MemMapEntries initialized in this array
have a static size and base address.
- extended_memmap, only initialized with entries located after the
RAM. MemMapEntries initialized in this array only get their size
initialized. Their base address is dynamically computed depending
on the the top of the RAM, with same alignment as their size.
Eventually base_memmap entries are copied into the extended_memmap
array. Using two separate arrays however clarifies which entries
are statically allocated and those which are dynamically allocated.
This new split will allow to grow the RAM size without changing the
description of the high IO entries.
We introduce a new virt_set_memmap() helper function which
"freezes" the memory map. We call it in machvirt_init as
memory attributes of the machine are not yet set when
virt_instance_init() gets called.
The memory map is unchanged (the top of the initial RAM still is
256GiB). Then come the high IO regions with same layout as before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a split of the memory map into a static
part and a dynamic part floating after the RAM, let's rename the
regions located after the RAM
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch virtio's self announcement to use the AnnounceTimer.
It keeps it's own AnnounceTimer (per device), and starts running it
using a migration post-load and a virtual clock; that way the
announce happens once the guest is actually running.
The timer uses the migration parameters to set the timing of
the repeats.
Based on earlier patches by myself and
Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccBqMAAoJECgfDbjSjVRpvSEIAKYPRNdCBX/SSS/L/tmJS5Zt
8IyU/HW1YJ249vO+aT6z4Q3QPgqNC3KjXC3brx/WRoPZnRroen4rv2Kqnk6SayPa
a52d2ubXKWxb3swdG1CAVzFRhq/ABpgAPx0dr1JW+RXgo2lxpJ4GNYxKMosQTaPE
hRNeXl1XlcIK525kJhFH3Hlij9mTRuY6T7ydpPQd8dUq2dBRaL9RrzZRrkZxCy6l
gQPUqNzPhG0XXyOiJmwYyVX0zGzbYrMLrMQAor2SBIYmU+zv2eZGPJUYxoMTUMzt
YR0WCpvkvPITlAryaBoozAIDYVz8PxBRT1KRwpDal+2rzlm6o+veKDiF8R46gn0=
=GzUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, tests
Lots of work on tests: BiosTablesTest UEFI app,
vhost-user testing for non-Linux hosts.
Misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 22 Feb 2019 15:51:40 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (26 commits)
pci: Sanity test minimum downstream LNKSTA
hw/smbios: fix offset of type 3 sku field
pci: Move NVIDIA vendor id to the rest of ids
virtio-balloon: Safely handle BALLOON_PAGE_SIZE < host page size
virtio-balloon: Use ram_block_discard_range() instead of raw madvise()
virtio-balloon: Rework ballon_page() interface
virtio-balloon: Corrections to address verification
virtio-balloon: Remove unnecessary MADV_WILLNEED on deflate
i386/kvm: ignore masked irqs when update msi routes
contrib/vhost-user-blk: fix the compilation issue
Revert "contrib/vhost-user-blk: fix the compilation issue"
pc-dimm: use same mechanism for [get|set]_addr
tests/data: introduce "uefi-boot-images" with the "bios-tables-test" ISOs
tests/uefi-test-tools: add build scripts
tests: introduce "uefi-test-tools" with the BiosTablesTest UEFI app
roms: build the EfiRom utility from the roms/edk2 submodule
roms: add the edk2 project as a git submodule
vhost-user-test: create a temporary directory per TestServer
vhost-user-test: small changes to init_hugepagefs
vhost-user-test: create a main loop per TestServer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
-----BEGIN PGP SIGNATURE-----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=XTkI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/i2c-for-release-20190228' into staging
This has been out there long enough, I need to get this in.
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
# gpg: Signature made Thu 28 Feb 2019 18:05:49 GMT
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/i2c-for-release-20190228:
i2c: Verify that the count passed in to smbus_eeprom_init() is valid
i2c:smbus_eeprom: Add a reset function to smbus_eeprom
i2c:smbus_eeprom: Add vmstate handling to the smbus eeprom
i2c:smbus_eeprom: Add a size constant for the smbus_eeprom size
i2c:smbus_eeprom: Add normal type name and cast to smbus_eeprom.c
i2c:smbus_slave: Add an SMBus vmstate structure
i2c:pm_smbus: Fix state transfer
migration: Add a VMSTATE_BOOL_TEST() macro
i2c:pm_smbus: Fix pm_smbus handling of I2C block read
boards.h: Ignore migration for SMBus devices on older machines
i2c:smbus: Make white space in switch statements consistent
i2c:smbus_eeprom: Get rid of the quick command
i2c:smbus: Simplify read handling
i2c:smbus: Simplify write operation
i2c:smbus: Correct the working of quick commands
i2c: Don't check return value from i2c_recv()
arm:i2c: Don't mask return from i2c_recv()
i2c: have I2C receive operation return uint8_t
i2c: Split smbus into parts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* add MHU and dual-core support to Musca boards
* refactor some VFP insns to be gated by ID registers
* Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
* Implement ARMv8.2-FHM extension
* Advertise JSCVT via HWCAP for linux-user
-----BEGIN PGP SIGNATURE-----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=7MnB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190228-1' into staging
target-arm queue:
* add MHU and dual-core support to Musca boards
* refactor some VFP insns to be gated by ID registers
* Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
* Implement ARMv8.2-FHM extension
* Advertise JSCVT via HWCAP for linux-user
# gpg: Signature made Thu 28 Feb 2019 11:06:55 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190228-1:
linux-user: Enable HWCAP_ASIMDFHM, HWCAP_JSCVT
target/arm: Enable ARMv8.2-FHM for -cpu max
target/arm: Implement VFMAL and VFMSL for aarch32
target/arm: Implement FMLAL and FMLSL for aarch64
target/arm: Add helpers for FMLAL
Revert "arm: Allow system registers for KVM guests to be changed by QEMU code"
target/arm: Gate "miscellaneous FP" insns by ID register field
target/arm: Use MVFR1 feature bits to gate A32/T32 FP16 instructions
hw/arm/armsse: Unify init-svtor and cpuwait handling
hw/arm/iotkit-sysctl: Implement CPUWAIT and INITSVTOR*
hw/arm/iotkit-sysctl: Add SSE-200 registers
hw/misc/iotkit-sysctl: Correct typo in INITSVTOR0 register name
target/arm/arm-powerctl: Add new arm_set_cpu_on_and_reset()
target/arm/cpu: Allow init-svtor property to be set after realize
hw/arm/armsse: Wire up the MHUs
hw/misc/armsse-mhu.c: Model the SSE-200 Message Handling Unit
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the handling of init-svtor and cpuwait initial
values is split between armsse.c and iotkit-sysctl.c:
the code in armsse.c sets the initial state of the CPU
object by setting the init-svtor and start-powered-off
properties, but the iotkit-sysctl.c code has its own
code setting the reset values of its registers (which are
then used when updating the CPU when the guest makes
runtime changes).
Clean this up by making the armsse.c code set properties on the
iotkit-sysctl object to define the initial values of the
registers, so they always match the initial CPU state,
and update the comments in armsse.c accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-9-peter.maydell@linaro.org
The SYSCTL block in the SSE-200 has some extra registers that
are not present in the IoTKit version. Add these registers
(as reads-as-written stubs), enabled by a new QOM property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-7-peter.maydell@linaro.org
The iotkit-sysctl device has a register it names INITSVRTOR0.
This is actually a typo present in the IoTKit documentation
and also in part of the SSE-200 documentation: it should be
INITSVTOR0 because it is specifying the initial value of the
Secure VTOR register in the CPU. Correct the typo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-6-peter.maydell@linaro.org
Create and connect the MHUs in the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-3-peter.maydell@linaro.org
Implement a model of the Message Handling Unit (MHU) found in
the Arm SSE-200. This is a simple device which just contains
some registers which allow the two cores of the SSE-200
to raise interrupts on each other.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-2-peter.maydell@linaro.org
Next set of patches for ppc and spapr. There's a lot in this one:
* Support "STOP light" states on POWER9
* Add support for HVI interrupts on POWER9 (powernv machine)
* CVE-2019-8934: Don't leak host model and serial information to the guest
* Tests and cleanups for various hot unplug options
* Hash and radix MMU implementation on POWER9 for powernv machine
* PCI Host Bridge hotplug support for pseries machine
* Allow larger kernels and initrds for powernv machine
Plus a handful of miscellaneous fixes and cleanups.
The cpu hotplug tests and cleanups from David Hildenbrand aren't
solely power related. However the consensus amongst Michael Tsirkin,
David Hildenbrand, Cornelia Huck and myself was that it made most
sense to come in via my tree.
-----BEGIN PGP SIGNATURE-----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=Z4Z6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20190226' into staging
ppc patch queue 2019-02-26
Next set of patches for ppc and spapr. There's a lot in this one:
* Support "STOP light" states on POWER9
* Add support for HVI interrupts on POWER9 (powernv machine)
* CVE-2019-8934: Don't leak host model and serial information to the guest
* Tests and cleanups for various hot unplug options
* Hash and radix MMU implementation on POWER9 for powernv machine
* PCI Host Bridge hotplug support for pseries machine
* Allow larger kernels and initrds for powernv machine
Plus a handful of miscellaneous fixes and cleanups.
The cpu hotplug tests and cleanups from David Hildenbrand aren't
solely power related. However the consensus amongst Michael Tsirkin,
David Hildenbrand, Cornelia Huck and myself was that it made most
sense to come in via my tree.
# gpg: Signature made Tue 26 Feb 2019 03:37:46 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20190226: (50 commits)
ppc/pnv: use IEC binary prefixes to represent sizes
ppc/pnv: add INITRD_MAX_SIZE constant
ppc/pnv: increase kernel size limit to 256MiB
hw/ppc: Use object_initialize_child for correct reference counting
ppc/xive: xive does not have a POWER7 interrupt model
tests/device-plug: Add PHB unplug request test for spapr
spapr: enable PHB hotplug for default pseries machine type
spapr: add hotplug hooks for PHB hotplug
spapr_pci: add ibm, my-drc-index property for PHB hotplug
spapr_pci: provide node start offset via spapr_populate_pci_dt()
spapr_events: add support for phb hotplug events
spapr: populate PHB DRC entries for root DT node
spapr: create DR connectors for PHBs
spapr_pci: add PHB unrealize
spapr_irq: Expose the phandle of the interrupt controller
spapr: Expose the name of the interrupt controller node
xics: Write source state to KVM at claim time
spapr/drc: Drop spapr_drc_attach() fdt argument
spapr/pci: Generate FDT fragment at configure connector time
spapr: Generate FDT fragment for CPUs at configure connector time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no vmstate handling for SMBus, so no device sitting on SMBus
can have a state transfer that works reliably. So add it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Transfer the state information for the SMBus registers and
internal data so it will work on a VM transfer.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The I2C block read function of pm_smbus was completely broken. It
required doing some direct I2C handling because it didn't have a
defined size, the OS code just reads bytes until it marks the
transaction finished.
This also required adjusting how the AMIBIOS workaround code worked,
the I2C block mode was setting STS_HOST_BUSY during a transaction,
so that bit could no longer be used to inform the host status read
code to start the transaction. Create a explicit bool for that
operation.
Also, don't read the next byte from the device in byte-by-byte
mode unless the OS is actually clearing the byte done bit. Just
assuming that's what the OS is doing is a bad idea.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Migration capability is being added for pm_smbus and SMBus devices.
This change will allow backwards compatibility to be kept when
migrating back to an old qemu version. Add a bool to the machine
class tho keep smbus migration from happening. Future changes
will use this.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
There were two different read functions, and with the removal of
the command passed in there is no functional difference. So remove
one of them. With that you don't need one of the states, so that
can be removed, too.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There were two different write functions and the SMBus code kept
track of the command.
Keeping track of the command wasn't useful, in fact it wasn't quite
correct for the eeprom_smbus code. And there is no need for two write
functions. Just have one write function and the first byte in the
buffer is the command.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The logic of handling quick SMBus commands was wrong. If you get a
finish event with no data, that's a quick command.
Document the quick command while we are at it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Hotplugging PHBs is a machine-level operation, but PHBs reside on the
main system bus, so we register spapr machine as the handler for the
main system bus.
Provide the usual pre-plug, plug and unplug-request handlers.
Move the checking of the PHB index to the pre-plug handler. It is okay
to do that and assert in the realize function because the pre-plug
handler is always called, even for the oldest machine types we support.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
(Fixed interrupt controller phandle in "interrupt-map" and
TCE table size in "ibm,dma-window" FDT fragment, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059672926.1466090.13612804072190051439.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PHB hotplug re-uses PHB device tree generation code and passes
it to a guest via RTAS. Doing this requires knowledge of where
exactly in the device tree the node describing the PHB begins.
Provide this via a new optional pointer that can be used to
store the PHB node's start offset.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059671912.1466090.10891589403973703473.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059670389.1466090.10015601248906623076.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support PHB hotplug we need to clean up lingering references,
memory, child properties, etc. prior to the PHB object being
finalized. Generally this will be called as a result of calling
object_unparent() on the PHB object, which in turn would normally
be called as the result of an unplug() operation.
When the PHB is finalized, child objects will be unparented in
turn, and finalized if the PHB was the only reference holder. so
we don't bother to explicitly unparent child objects of the PHB,
with the notable exception of DRCs. This is needed to avoid a QEMU
crash when unplugging a PHB and resetting the machine before the
guest could handle the event. The DRCs are removed from the QOM tree
by pci_unregister_root_bus() and we must make sure we're not leaving
stale aliases under the global /dr-connector path.
The formula that gives the number of DMA windows is moved to an
inline function in the hw/pci-host/spapr.h header because it
will have other users.
The unrealize function is able to cope with partially realized PHBs.
It is hence used to implement proper rollback on the realize error
path.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <155059669881.1466090.13515030705986041517.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used by PHB hotplug in order to create the "interrupt-map"
property of the PHB node.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059669374.1466090.12943228478046223856.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be needed by PHB hotplug in order to access the "phandle"
property of the interrupt controller node.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <155059668867.1466090.6339199751719123386.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries machine only uses LSIs to support legacy PCI devices. Every
PHB claims 4 LSIs at realize time. When using in-kernel XICS (or upcoming
in-kernel XIVE), QEMU synchronizes the state of all irqs, including these
LSIs, later on at machine reset.
In order to support PHB hotplug, we need a way to tell KVM about the LSIs
that doesn't require a machine reset. An easy way to do that is to always
inform KVM when an interrupt is claimed, which really isn't a performance
path.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059668360.1466090.5969630516627776426.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All DRC subtypes have been converted to generate the FDT fragment at
configure connector time instead of attach time. The fdt and fdt_offset
arguments of spapr_drc_attach() aren't needed anymore. Drop them and
make the implementation of the dt_populate() method mandatory.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059667853.1466090.16527852453054217565.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059667346.1466090.326696113231137772.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059666839.1466090.3833376527523126752.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059666331.1466090.6766540766297333313.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current logic is to provide the FDT fragment when attaching a device
to a DRC. This works perfectly fine for our current hotplug support, but
soon we will add support for PHB hotplug which has some constraints, that
CPU, PCI and LMB devices don't seem to have.
The first constraint is that the "ibm,dma-window" property of the PHB
node requires the IOMMU to be configured, ie, spapr_tce_table_enable()
has been called, which happens during PHB reset. It is okay in the case
of hotplug since the device is reset before the hotplug handler is
called. On the contrary with coldplug, the hotplug handler is called
first and device is only reset during the initial system reset. Trying
to create the FDT fragment on the hotplug path in this case, would
result in somthing like this:
ibm,dma-window = < 0x80000000 0x00 0x00 0x00 0x00 >;
This will cause linux in the guest to panic, by simply removing and
re-adding the PHB using the drmgr command:
page = alloc_pages_node(nid, GFP_KERNEL, get_order(sz));
if (!page)
panic("iommu_init_table: Can't allocate %ld bytes\n", sz);
The second and maybe more problematic constraint is that the
"interrupt-map" property needs to reference the interrupt controller
node using the very same phandle that SLOF has already exposed to the
guest. QEMU requires SLOF to call the private KVMPPC_H_UPDATE_DT hcall
at some point to know about this phandle. With the latest QEMU and SLOF,
this happens when SLOF gets quiesced. This means that if the PHB gets
hotplugged after CAS but before SLOF quiesce, then we're sure that the
phandle is not known when the hotplug handler is called.
The FDT is only needed when the guest first invokes RTAS to configure
the connector actually, long after SLOF quiesce. Let's postpone the
creation of FDT fragments for PHBs to rtas_ibm_configure_connector().
Since we only need this for PHBs, introduce a new method in the base
DRC class for that. DRC subtypes will be converted to use it in
subsequent patches.
Allow spapr_drc_attach() to be passed a NULL fdt argument if the method
is available. When all DRC subtypes have been converted, the fdt argument
will eventually disappear.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059665823.1466090.18358845122627355537.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The HW relies on LPCR:HR along with the PATE to determine whether
to use Radix or Hash mode. In fact it uses LPCR:HR more commonly
than the PATE.
For us, it's also more efficient to do so, especially since unlike
the HW we do not maintain a cache of the current PATE and HV PATE
in a generic place.
Prepare the grounds for that by ensuring that LPCR:HR is set
properly on SPAPR machines.
Another option would have been to use a callback to get the PATE
but this gets messy when implementing bare metal support, it's
much simpler (and faster) to use LPCR.
Since existing migration streams may not have it, fix it up in
spapr_post_load() as well based on the pseudo-PATE entry that
we keep.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215170029.15641-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On ppc hosts, hypervisor shares following system attributes
- /proc/device-tree/system-id
- /proc/device-tree/model
with a guest. This could lead to information leakage and misuse.[*]
Add machine attributes to control such system information exposure
to a guest.
[*] https://wiki.openstack.org/wiki/OSSN/OSSN-0028
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Fix-suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20190218181349.23885-1-ppandit@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Adds support for the Hypervisor directed interrupts in addition to the
OS ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - modified the icp_realize() and xive_tctx_realize() to take
into account explicitely the POWER9 interrupt model
- introduced a specific power9_set_irq for POWER9 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215161648.9600-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccAIFAAoJEJykq7OBq3PImM0IAMcC92GYwSL6MgQ4NrfbVfDQ
P+qgIoxlXcYNwa12kGY6rE4tgSDab9Mc5ACpmuFdr8Xj7/JOp97AccmKZ+RzYQSj
IFlkvd8GngQR1YnFGV6PIWSt7hRhKuUZMqSIDrWro/MTdiJFEMI8/e7QLGxmaEX1
gWCNSopxJUeACSJiRyfZvBGNCs23R9ptFKBFhIXS98KPtEtF8LQV0JnQXoRUDiBL
G9C/xggdGDvct3Id4yOBCh43ErssyOrlYwjzIRWB2AFfIwHGytJcL6JBjAqy4Z7M
ClMNXaQSbfSCXrc3osF9nO6KaFduhfpUH44lL5JBHxUgH6pN2xGradRANZwysQM=
=DSBn
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
Pull request
# gpg: Signature made Fri 22 Feb 2019 14:07:01 GMT
# gpg: using RSA key 9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request: (27 commits)
tests/virtio-blk: add test for DISCARD command
tests/virtio-blk: add test for WRITE_ZEROES command
tests/virtio-blk: add virtio_blk_fix_dwz_hdr() function
tests/virtio-blk: change assert on data_size in virtio_blk_request()
virtio-blk: add DISCARD and WRITE_ZEROES features
virtio-blk: set config size depending on the features enabled
virtio-net: make VirtIOFeature usable for other virtio devices
virtio-blk: add "discard" and "write-zeroes" properties
virtio-blk: add host_features field in VirtIOBlock
virtio-blk: add acct_failed param to virtio_blk_handle_rw_error()
hw/ide: drop iov field from IDEDMA
hw/ide: drop iov field from IDEBufferedRequest
hw/ide: drop iov field from IDEState
tests/test-bdrv-drain: use QEMU_IOVEC_INIT_BUF
migration/block: use qemu_iovec_init_buf
qemu-img: use qemu_iovec_init_buf
block/vmdk: use qemu_iovec_init_buf
block/qed: use qemu_iovec_init_buf
block/qcow2: use qemu_iovec_init_buf
block/qcow: use qemu_iovec_init_buf
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The type 3 SMBIOS structure[1] ends with fields
...
0x14 - contained element count
0x15 - contained element record length
0x16 - sku number
The smbios_type_3 struct missed the contained element record
length field, causing sku number to be reported at the wrong
offset.
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0134_3.1.1.pdf
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190215153600.1770727-1-berrange@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Fixes: e41fca3da7
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
sPAPR code will use it too so move it from VFIO to the common code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190214051440.59167-1-aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio-balloon always works in units of 4kiB (BALLOON_PAGE_SIZE), but
we can only actually discard memory in units of the host page size.
Now, we handle this very badly: we silently ignore balloon requests that
aren't host page aligned, and for requests that are host page aligned we
discard the entire host page. The latter can corrupt guest memory if its
page size is smaller than the host's.
The obvious choice would be to disable the balloon if the host page size is
not 4kiB. However, that would break the special case where host and guest
have the same page size, but that's larger than 4kiB. That case currently
works by accident[1] - and is used in practice on many production POWER
systems where 64kiB has long been the Linux default page size on both host
and guest.
To make the balloon safe, without breaking that useful special case, we
need to accumulate 4kiB balloon requests until we have a whole contiguous
host page to discard.
We could in principle do that across all guest memory, but it would require
a large bitmap to track. This patch represents a compromise: we track
ballooned subpages for a single contiguous host page at a time. This means
that if the guest discards all 4kiB chunks of a host page in succession,
we will discard it. This is the expected behaviour in the (host page) ==
(guest page) != 4kiB case we want to support.
If the guest scatters 4kiB requests across different host pages, we don't
discard anything, and issue a warning. Not ideal, but at least we don't
corrupt guest memory as the previous version could.
Warning reporting is kind of a compromise here. Determining whether we're
in a problematic state at realize() time is tricky, because we'd have to
look at the host pagesizes of all memory backends, but we can't really know
if some of those backends could be for special purpose memory that's not
subject to ballooning.
Reporting only when the guest tries to balloon a partial page also isn't
great because if the guest page size happens to line up it won't indicate
that we're in a non ideal situation. It could also cause alarming repeated
warnings whenever a migration is attempted.
So, what we do is warn the first time the guest attempts balloon a partial
host page, whether or not it will end up ballooning the rest of the page
immediately afterwards.
[1] Because when the guest attempts to balloon a page, it will submit
requests for each 4kiB subpage. Most will be ignored, but the one
which happens to be host page aligned will discard the whole lot.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190214043916.22128-6-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds the support of DISCARD and WRITE_ZEROES commands,
that have been introduced in the virtio-blk protocol to have
better performance when using SSD backend.
We support only one segment per request since multiple segments
are not widely used and there are no userspace APIs that allow
applications to submit multiple segments in a single call.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-7-sgarzare@redhat.com
Message-Id: <20190221103314.58500-7-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Starting from DISABLE and WRITE_ZEROES features, we use an array of
VirtIOFeature (as virtio-net) to properly set the config size
depending on the features enabled.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-6-sgarzare@redhat.com
Message-Id: <20190221103314.58500-6-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In order to use VirtIOFeature also in other virtio devices, we move
its declaration and the endof() macro (renamed in virtio_endof())
in virtio.h.
We add virtio_feature_get_config_size() function to iterate the array
of VirtIOFeature and to return the config size depending on the
features enabled. (as virtio_net_set_config_size() did)
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-5-sgarzare@redhat.com
Message-Id: <20190221103314.58500-5-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Since configurable features for virtio-blk are growing, this patch
adds host_features field in the struct VirtIOBlock. (as in virtio-net)
In this way, we can avoid to add new fields for new properties and
we can directly set VIRTIO_BLK_F* flags in the host_features.
We update "config-wce" and "scsi" property definition to use the new
host_features field without change the behaviour.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190221103314.58500-3-sgarzare@redhat.com
Message-Id: <20190221103314.58500-3-sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-18-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-18-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-17-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-17-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-16-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-16-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch adds EDID support to the family of virtio-gpu devices. It is
turned off by default, use the new edid property to enable it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190221081054.13853-1-kraxel@redhat.com
The region 0x40010000 .. 0x4001ffff and its secure-only alias
at 0x50010000... are for per-CPU devices. We implement this by
giving each CPU its own container memory region, where the
per-CPU devices live. Unfortunately, the alias region which
makes devices mapped at 0x4... addresses also appear at 0x5...
is only implemented in the overall "all CPUs" container. The
effect of this bug is that the CPU_IDENTITY register block appears
only at 0x4001f000, but not at the 0x5001f000 alias where it should
also appear. Guests (like very recent Arm Trusted Firmware-M)
which try to access it at 0x5001f000 will crash.
Fix this by moving the handling for this alias from the "all CPUs"
container to the per-CPU container. (We leave the aliases for
0x1... and 0x3... in the overall container, because there are
no per-CPU devices there.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190215180500.6906-1-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The Musca boards have DAPLink firmware that sets the initial
secure VTOR value (the location of the vector table) differently
depending on the boot mode (from flash, from RAM, etc). Export
the init-svtor as a QOM property of the ARMSSE object so that
the board can change it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
In commit 4b635cf7a9 we added a QOM property to the ARMSSE
object, but forgot to add it to the documentation comment in the
header. Correct the omission.
Fixes: 4b635cf7a9 ("hw/arm/armsse: Make SRAM bank size configurable")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL011 UART has six interrupt lines:
* RX (receive data)
* TX (transmit data)
* RT (receive timeout)
* MS (modem status)
* E (errors)
* combined (logical OR of all the above)
So far we have only emulated the combined interrupt line;
add support for the others, so that boards that wire them
up to different interrupt controller inputs can do so.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl011's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl031's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Peripheral Protection Controller's handling of unused ports
is that if there is nothing connected to the port's downstream
then it does not create the sysbus MMIO region for the upstream
end of the port. This results in odd behaviour when there is
an unused port in the middle of the range: since sysbus MMIO
regions are implicitly consecutively allocated, any used ports
above the unused ones end up with sysbus MMIO region numbers
that don't match the port number.
Avoid this numbering mismatch by creating dummy MMIO regions
for the unused ports. This doesn't change anything for our
existing boards, which don't have any gaps in the middle of
the port ranges they use; but it will be needed for the Musca
board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=QQra
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20190219' into staging
ppc patch queue 2019-02-19
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
# gpg: Signature made Mon 18 Feb 2019 13:47:54 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20190219: (43 commits)
target/ppc: convert vmin* and vmax* to vector operations
target/ppc: convert vadd*s and vsub*s to vector operations
target/ppc: Split out VSCR_SAT to a vector field
target/ppc: Add set_vscr_sat
target/ppc: Use mtvscr/mfvscr for vmstate
target/ppc: Add helper_mfvscr
target/ppc: Remove vscr_nj and vscr_sat
target/ppc: Use helper_mtvscr for reset and gdb
target/ppc: Pass integer to helper_mtvscr
target/ppc: convert xxsel to vector operations
target/ppc: convert xxspltw to vector operations
target/ppc: convert xxspltib to vector operations
target/ppc: convert VSX logical operations to vector operations
target/ppc: convert vsplt[bhw] to use vector operations
target/ppc: convert vspltis[bhw] to use vector operations
target/ppc: convert vaddu[b,h,w,d] and vsubu[b,h,w,d] over to use vector operations
target/ppc: convert VMX logical instructions to use vector operations
xics: Drop the KVM ICS class
spapr/irq: Use the "simple" ICS class for KVM
xics: Handle KVM interrupt presentation from "simple" ICS code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We will need these from CONFIG_USER_ONLY as well,
which cannot access include/hw/.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190212053044.29015-2-richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The KVM ICS class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023084177.1011724.14693955932559990358.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We want to use the "simple" ICS type in both KVM and non-KVM setups.
Teach the "simple" ICS how to present interrupts to KVM and adapt
sPAPR accordingly.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082996.1011724.16237920586343905010.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICSStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081817.1011724.14078777320394028836.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081228.1011724.12474992370439652538.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The base ICP class knows how to interact with KVM. Adapt sPAPR to use it
instead of the ICP KVM class.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080638.1011724.792095453419098948.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The realization of KVM ICP currently follows the parent_realize logic,
which is a bit overkill here. Also we want to get rid of the KVM ICP
class. Explicitely call icp_kvm_realize() from the base ICP realize
function.
Note that ICPStateClass::parent_realize is retained because powernv
needs it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080049.1011724.15423463482790260696.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP reset handler simply writes the ICP state to KVM. This
doesn't need the overkill parent_reset logic we have today. Call
icp_set_kvm_state() from the base ICP reset function instead.
Since there are no other users for ICPStateClass::parent_reset, and
it isn't currently expected to change, drop it as well.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023079461.1011724.12644984391500635645.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICPStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023078871.1011724.3083923389814185598.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using the 'dual' interrupt mode, the source numbers of both sPAPR
IRQ backends are aligned to share a common IRQ number space and to use
a similar mapping of the machine qemu_irq array which is indexed by
the source number.
The XICS IRQ number range initially being [ 0x1000 - 0x2000 ], this
requires to change the XICS ICSState offset to 0 and to provision for
an extra 4K of source numbers and qemu_irqs which will never be used
by the machine when running under the XICS interrupt mode. This is not
an optimal solution.
Change the init() method to allocate an IRQ number space of the
expected size for the XICS sPAPR IRQ backend. It breaks the interrupt
signaling when under the 'dual' mode because source numbers have
unexpected values but next patch will fix that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190213210756.27032-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Certain devices types, like memory/CPU, are now being handled using a
hotplug interface provided by a top-level MachineClass. Hotpluggable
host bridges are another such device where it makes sense to use a
machine-level hotplug handler. However, unlike those devices,
host-bridges have a parent bus (the main system bus), and devices with
a parent bus use a different mechanism for registering their hotplug
handlers: qbus_set_hotplug_handler(). This interface currently expects
a handler to be a subclass of DeviceClass, but this is not the case
for MachineClass, which derives directly from ObjectClass.
Internally, the interface only requires an ObjectClass, so expose that
in qbus_set_hotplug_handler().
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <154999589921.690774.3640149277362188566.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MSI is the default and LSI specific code is guarded by the
xive_source_irq_is_lsi() helper. The xive_source_irq_set()
helper is a nop for MSIs.
Simplify the code by turning xive_source_irq_set() into
xive_source_irq_set_lsi() and only call it for LSIs. The
call to xive_source_irq_set(false) in spapr_xive_irq_free()
is also a nop. Just drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <154999584656.690774.18352404495120358613.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All this code is used with both the XICS and XIVE interrupt controllers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
vhost user blk discard/write zeroes features
misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcWbMUAAoJECgfDbjSjVRp2acH+wa8abfyQIpVMji+cdvcw7Wo
yJjCoPxX0y+tm7FGp6YjyyQhSzjUYRS+71NL6xkZVxs8yh4ZCbb/xDRYmrVG2cb6
6tUcqp1zlMp+w+kVKS4m4WTb0Z1bIODOi99tNBXxYjWY9lXF/hjZbhRpt6vL/NaP
hqYtp+wlhyjxsY/GFn5XZLY7F6+QKq/lsMJD80FvbtHBh/ngqmgyoouNwYzg1faW
M3wD5A3IOXLzU+MGK6uCtKK0+t3xzvaVJL7zChimKkn+y+Pg9T+s04zQS739bJRg
dYYrVK3IOt2tvVxBZnnUm9eBIxxElAxRssmERPe2i0mBRSXYKomuVZrXJ6ROhjA=
=TxWc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, cleanups, features
vhost user blk discard/write zeroes features
misc cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 05 Feb 2019 16:00:20 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
contrib/libvhost-user: cleanup casts
r2d: fix build on mingw
mmap-alloc: fix hugetlbfs misaligned length in ppc64
mmap-alloc: unfold qemu_ram_mmap()
i386, acpi: cleanup build_facs by removing second unused argument
fw_cfg: fix the life cycle and the name of "qemu_extra_params_fw"
acpi: Make TPM 2.0 with TIS available as MSFT0101
hw/virtio: Use CONFIG_VIRTIO_PCI switch instead of CONFIG_PCI
vhost-user-blk: add discard/write zeroes features support
contrib/vhost-user-blk: fix the compilation issue
pci/msi: export msi_is_masked()
intel_iommu: reset intr_enabled when system reset
intel_iommu: fix operator in vtd_switch_address_space
hw: virtio-pci: drop DO_UPCAST
include: update Linux headers to 4.21-rc1/5.0-rc1
scripts/update-linux-headers.sh: adjust for Linux 4.21-rc1 (or 5.0-rc1)
contrib/libvhost-user: switch to uint64_t
virtio: add checks for the size of the indirect table
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It is going to be used later on outside MSI code to detect whether one
MSI vector is masked out.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It's been deprecated since QEMU 3.0, and nobody complained so far, so
it is time to remove this option now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1544684731-18828-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to avoid migration issues, we enable PVH only for
machine type >= 4.0
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The x86/HVM direct boot ABI permits Qemu to be able to boot directly
into the uncompressed Linux kernel binary with minimal firmware involvement.
https://xenbits.xen.org/docs/unstable/misc/pvh.html
This commit adds the header file that defines the start_info struct
that needs to be populated in order to use this ABI.
The canonical version of start_info.h is in the Xen codebase.
(like QEMU, the Linux kernel uses a copy as well).
Signed-off-by: Liam Merwick <Liam.Merwick@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <Konrad.Wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a routine which, given a pointer to a range of ELF Notes,
searches through them looking for a note matching the type specified
and returns a pointer to the matching ELF note.
get_elf_note_type() is used by elf_load[32|64]() to find the
specified note type required by the 'elf_note_fn' parameter
added in the previous commit.
Signed-off-by: Liam Merwick <Liam.Merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- fix CPU wakeup on runstall changes; expose runstall as an IRQ line;
- place mini-bootloader at the BSP reset vector;
- expose CPU core frequency in XTFPGA board FPGA register;
- rearrange access to external interrupts of xtensa cores;
- add MX interrupt distributor and use it on SMP XTFPGA boards;
- add test_mmuhifi_c3 xtensa core variant;
- raise number of CPUs that can be instantiated on XTFPGA boards.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEK2eFS5jlMn3N6xfYUfnMkfg/oEQFAlxYi5QTHGpjbXZia2Jj
QGdtYWlsLmNvbQAKCRBR+cyR+D+gRCyJEACR/IQ7LVFYBczo450yLOoAPWU/8/iU
BmmeqM/BKZHBZN5HyS7zdBbDGHe/aQd+hlwG3hnxaJTfqTSOW0QxOmXkI2U5yQrl
SfGErboON0FnDreQuLlsRN0QQYI7pFJiwpUj5sqOYYghfbEfwmefUNzWlJr17AyC
AusLrGe3SBJuv40S78C+S7e4XlaGxPn5OwCvpvH+o8iDj9TCP7+vXV8N4fdackH+
i323F9OdNSmtKXL/lDVG2bf5eFw+koLOGPsqjdT/WIfRVg45VXd7ZFQeMZxuQrh4
8NwlQx9bxM4rbPBrUpsPDulic5udmMJvJ31CFe3YXu48skG90E3NxtOmUBGvTgMl
lpM9RzZfCZTAIfPqw0LHiQ4kaioMlAO40wtCNxqm78R5UL/FseuzNUN+eLz7qCL1
rTBKOQ5CJMFZWDkQjcwIYz54vi8QCt0jMWD4MzzIaU3Nf3Ak5uAaeEQE+b48lBvQ
0EhUzwh1Ea9An2JAyhAqlNqifs+0HsG4M5tqhVj+9IITlzbZe/zLswgYaHd5D75v
ElGoFov9Gi/GM5LxFzNRN1HwFCFWeHTt6sIHIo2oR1+mPrNhS+MJyqrnkKgIYOA/
plSJqO//iyS8wGL7c7UXVV3cixGOv7SSZDtSKFZb+sD7aML/y3DJnFTmABOl4kdt
OBYFg8+jcrma3g==
=8D60
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/xtensa/tags/20190204-xtensa' into staging
target/xtensa: SMP updates and various fixes
- fix CPU wakeup on runstall changes; expose runstall as an IRQ line;
- place mini-bootloader at the BSP reset vector;
- expose CPU core frequency in XTFPGA board FPGA register;
- rearrange access to external interrupts of xtensa cores;
- add MX interrupt distributor and use it on SMP XTFPGA boards;
- add test_mmuhifi_c3 xtensa core variant;
- raise number of CPUs that can be instantiated on XTFPGA boards.
# gpg: Signature made Mon 04 Feb 2019 18:59:32 GMT
# gpg: using RSA key 2B67854B98E5327DCDEB17D851F9CC91F83FA044
# gpg: issuer "jcmvbkbc@gmail.com"
# gpg: Good signature from "Max Filippov <filippov@cadence.com>" [unknown]
# gpg: aka "Max Filippov <max.filippov@cogentembedded.com>" [full]
# gpg: aka "Max Filippov <jcmvbkbc@gmail.com>" [full]
# Primary key fingerprint: 2B67 854B 98E5 327D CDEB 17D8 51F9 CC91 F83F A044
* remotes/xtensa/tags/20190204-xtensa:
hw/xtensa: xtfpga: raise CPU number limit
target/xtensa: add test_mmuhifi_c3 core
hw/xtensa: xtfpga: use MX PIC for SMP
target/xtensa: add MX interrupt controller
target/xtensa: expose core runstall as an IRQ line
target/xtensa: rearrange access to external interrupts
target/xtensa: drop function xtensa_timer_irq
target/xtensa: fix access to the INTERRUPT SR
hw/xtensa: xtfpga: use core frequency
hw/xtensa: xtfpga: fix bootloader placement in SMP
target/xtensa: add qemu_cpu_kick to xtensa_runstall
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Next step is to remove them from under the PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Include the interrupt presenter under the machine_data as we plan to
remove it from under PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It provides a mean to retrieve the XiveTCTX of a CPU. This will become
necessary with future changes which move the interrupt presenter
object pointers under the PowerPCCPU machine_data.
The PowerNV machine has an extra requirement on TIMA accesses that
this new method addresses. The machine can perform indirect loads and
stores on the TIMA on behalf of another CPU. The PIR being defined in
the controller registers, we need a way to peek in the controller
model to find the PIR value.
The XiveTCTX is moved above the XiveRouter definition to avoid forward
typedef declarations.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To avoid overflow if larger values are added later use ram_addr_t for
the sdram_bank_sizes parameter to match ram_size to which it is compared.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are several boards with SPD EEPROMs that are now using
duplicated or slightly different hard coded data. Add a helper to
generate SPD data for a memory module of given type and size that
could be used by these boards (either as is or with further changes if
needed) which should help cleaning this up and avoid further duplication.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The nRF51 contains three regions of non-volatile memory (NVM):
- CODE (R/W): contains code
- FICR (R): Factory information like code size, chip id etc.
- UICR (R/W): Changeable configuration data. Lock bits, Code
protection configuration, Bootloader address, Nordic SoftRadio
configuration, Firmware configuration.
Read and write access to the memories is managed by the
Non-volatile memory controller.
Memory schema:
[ CPU ] -+- [ NVM, either FICR, UICR or CODE ]
| |
\- [ NVMC ]
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190201023357.22596-2-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the SSE-200, now we have put in all
the code that lets us make it different from the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-22-peter.maydell@linaro.org
Instantiate a copy of the CPU_IDENTITY register block for each CPU
in an SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-21-peter.maydell@linaro.org
The SSE-200 has a CPU_IDENTITY register block, which is a set of
read-only registers. As well as the usual PID/CID registers, there
is a single CPUID register which indicates whether the CPU is CPU 0
or CPU 1. Implement a model of this register block.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-20-peter.maydell@linaro.org
The SSE-200 has a "CPU local security control" register bank; add an
unimplemented-device stub for it. (The register bank has only one
interesting register, which allows the guest to lock down changes
to various CPU registers so they cannot be modified further. We
don't support that in our Cortex-M33 model anyway.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-19-peter.maydell@linaro.org
The SSE-200 gives each CPU a register bank to use to control its
L1 instruction cache. Put in an unimplemented-device stub for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-18-peter.maydell@linaro.org
Add unimplemented-device stubs for the various Power Policy Unit
devices that the SSE-200 has.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-17-peter.maydell@linaro.org
The SSE-200 has two Message Handling Units (MHUs), which sit behind
the APB PPC0. Wire up some unimplemented-device stubs for these,
since we don't yet implement a real model of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-16-peter.maydell@linaro.org
The SYS_VERSION and SYS_CONFIG register values differ between the
IoTKit and SSE-200. Make them configurable via QOM properties rather
than hard-coded, and set them appropriately in the ARMSSE code that
instantiates the IOTKIT_SYSINFO device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-15-peter.maydell@linaro.org
Create a cluster object to hold each CPU in the SSE. They are
logically distinct and may be configured differently (for instance
one may not have an FPU where the other does).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-14-peter.maydell@linaro.org
Give each CPU its own container memory region. This is necessary
for two reasons:
* some devices are instantiated one per CPU and the CPU sees only
its own device
* since a memory region can only be put into one container, we must
give each armv7m object a different MemoryRegion as its 'memory'
property, or a dual-CPU configuration will assert on realize when
the second armv7m object tries to put the MR into a container when
it is already in the first armv7m object's container
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-13-peter.maydell@linaro.org
The SSE-200 has two Cortex-M33 CPUs. These see the same view
of memory, with the exception of the "private CPU region" which
has per-CPU devices. Internal device interrupts for SSE-200
devices are mostly wired up to both CPUs, with the exception of
a few per-CPU devices. External GPIO inputs on the SSE-200
device are provided for the second CPU's interrupts above 32,
as is already the case for the first CPU.
Refactor the code to support creation of multiple CPUs.
For the moment we leave all CPUs with the same view of
memory: this will not work in the multiple-CPU case, but
we will fix this in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-12-peter.maydell@linaro.org
For the IoTKit the SRAM bank size is always 32K (15 bits); for the
SSE-200 this is a configurable parameter, which defaults to 32K but
can be changed when it is built into a particular SoC. For instance
the Musca-B1 board sets it to 128K (17 bits).
Make the bank size a QOM property. We follow the SSE-200 hardware in
naming the parameter SRAM_ADDR_WIDTH, which specifies the number of
address bits of a single SRAM bank.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-11-peter.maydell@linaro.org
The SSE-200 has four banks of SRAM, each with its own
Memory Protection Controller, where the IoTKit has only one.
Make the number of SRAM banks a field in ARMSSEInfo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-10-peter.maydell@linaro.org
The SSE-200 has 4 banks of SRAM, each with its own internal
Memory Protection Controller. The interrupt status for these
extra MPCs appears in the same security controller SECMPCINTSTATUS
register as the MPC for the IoTKit's single SRAM bank. Enhance the
iotkit-secctl device to allow 4 MPCs. (If the particular IoTKit/SSE
variant in use does not have all 4 MPCs then the unused inputs will
simply result in the SECMPCINTSTATUS bits being zero as required.)
The hardcoded constant "1"s in armsse.c indicate the actual number
of SRAM MPCs the IoTKit has, and will be replaced in the following
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-9-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
The Arm SSE-200 Subsystem for Embedded is a revised and
extended version of the older IoTKit SoC. Prepare for
adding a model of it by refactoring the IoTKit code into
an abstract base class which contains the functionality,
driven by a class data block specific to each subclass.
(This is the same approach used by the existing bcm283x
SoC family implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-6-peter.maydell@linaro.org
The Arm IoTKit was effectively the forerunner of a series of
subsystems for embedded SoCs, named the SSE-050, SSE-100 and SSE-200:
https://developer.arm.com/products/system-design/subsystems
These are generally quite similar, though later iterations have
extra devices that earlier ones do not.
We want to add a model of the SSE-200, which means refactoring the
IoTKit code into an abstract base class and subclasses (using the
same design that the bcm283x SoC and Aspeed SoC family
implementations do). As a first step, rename the IoTKit struct and
QOM macros to ARMSSE, which is what we're going to name the base
class. We temporarily retain TYPE_IOTKIT to avoid changing the
code that instantiates a TYPE_IOTKIT device here and then changing
it back again when it is re-introduced as a subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-5-peter.maydell@linaro.org
Expose "start-powered-off" as a property of the ARMv7M container,
which we just pass through to the CPU object in the same way that we
do for "init-svtor" and "idau". (We want this for the SSE-200, which
powers up only the first CPU at reset and leaves the second powered
down.)
As with the other CPU properties here, we can't just use alias
properties, because the CPU QOM object is not created until armv7m
realize time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-4-peter.maydell@linaro.org
Move the complexity of milkymist_tmu2_create() into the
source file. Doing so we avoid to include the X11/OpenGL
headers in all LM32 devices, and we also avoid the duplicate
declaration of glx_fbconfig_attr[] (it is already declared
in hw/display/milkymist-tmu2.c).
Since TYPE_MILKYMIST_TMU2 is now accessible, use it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190130120005.23123-5-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some files claim that the code is licensed under the GPL, but then
suddenly suggest that the user should have a look at the LGPL.
That's of course non-sense, replace it with the correct GPL wording
instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1548255083-8190-1-git-send-email-thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
apci_1_compatible should be acpi_1_compatible.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190125094047.22276-1-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
For TCG we want to distinguish which cluster a CPU is in, and
we need to do it quickly. Cache the cluster index in the CPUState
struct, by having the cluster object set cpu->cluster_index for
each CPU child when it is realized.
This means that board/SoC code must add all CPUs to the cluster
before realizing the cluster object. Regrettably QOM provides no
way to prevent adding children to a realized object and no way for
the parent to be notified when a new child is added to it, so
we don't have any way to enforce/assert this constraint; all
we can do is document it in a comment. We can at least put in a
check that the cluster contains at least one CPU, which should
catch the typical cases of "realized cluster too early" or
"forgot to parent the CPUs into it".
The restriction on how many clusters can exist in the system
is imposed by TCG code which will be added in a subsequent commit,
but the check to enforce it in cluster.c fits better in this one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190121152218.9592-3-peter.maydell@linaro.org
The m25p80 models dummy cycles using byte transfers. This works well
when the transfers are initiated by the QEMU model of a SPI controller
but when these are initiated by the OS, it breaks emulation.
Snoop the SPI transfer to catch commands requiring dummy cycles and
replace them with byte transfers compatible with the m25p80 model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20190124140519.13838-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Recent microbit firmwares panic if the TWI magnetometer/accelerometer
devices are not detected during startup. We don't implement TWI (I2C)
so let's stub out these devices just to let the firmware boot.
Signed-off by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190110094020.18354-2-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment style]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MX interrupt controller is a collection of the following devices
accessible through the external registers interface:
- interrupt distributor can route each external IRQ line to the
corresponding external IRQ pin of selected subset of connected xtensa
cores. It has per-CPU and per-IRQ enable signals and per-IRQ software
assert signals;
- IPI controller has 16 per-CPU IPI signals that may be routed to a
combination of 3 designated external IRQ pins of connected xtensa
cores;
- cache coherecy register controls core L1 cache participation in the
SMP cluster cache coherency protocol;
- runstall register lets BSP core stall and unstall AP cores.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The device is called via-ide and the modelled IDE controller is not
specific to 82C686B but is also usable independently. Therefore, change
function name prefixes accordingly to match device name.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 2905ced862c8d2ad509d73152171ce2472d72605.1548160772.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
Now that no CMD646 specific parts are left in CMD646BAR (all remaining
members are really PCI IDE specific) this struct can be deleted moving
the memory regions for PCI IDE BARs to PCIIDEState where they better
belong. The CMD646 PCI IDE model is adjusted accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 4b6cb2ae150dc0d21178209e4beb1e35140a7325.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
The io mem ops callbacks are not specific to CMD646 but really follow
the PCI IDE spec so move these from cmd646.c to pci.c to allow other
PCI IDE implementations to use them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: a2b1b2b74afdc78330b8b75605687f683a249635.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
The cmd646 io mem ops callbacks only need the IDEBus which is
currently passed via a CMD646BAR struct. No need to wrap it up like
that, we can pass it directly to these callbacks which then allows to
drop the IDEBus from the CMD646BAR.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 7a31c155c9899869794499d841d30c7ef32aae47.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
There was a pointer to PCIIDEState in CMD646BAR which was set but
not used afterwards. Get rid of this unused variable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1e352f091aa601fb2e19771aac46529fe278dd91.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
Commit 2974e916df introduced the VirtioNetRscChain structure which
refer to a VirtIONet, declared later, thus required VirtIONet typedef
to use a forward declaration.
However, when compiling with Clang in -std=gnu99 mode, this triggers
the following warning/error:
CC hw/net/virtio-net.o
In file included from qemu/hw/net/virtio-net.c:22:
include/hw/virtio/virtio-net.h:189:3: error: redefinition of typedef 'VirtIONet' is a C11 feature [-Werror,-Wtypedef-redefinition]
} VirtIONet;
^
include/hw/virtio/virtio-net.h:110:26: note: previous definition is here
typedef struct VirtIONet VirtIONet;
^
1 error generated.
make: *** [rules.mak:69: hw/net/virtio-net.o] Error 1
Fix it by removing the duplicate typedef definition.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When compiling the ppc code with clang and -std=gnu99, there are a
couple of warnings/errors like this one:
CC ppc64-softmmu/hw/intc/xics.o
In file included from hw/intc/xics.c:35:
include/hw/ppc/xics.h:43:25: error: redefinition of typedef 'ICPState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct ICPState ICPState;
^
target/ppc/cpu.h:1181:25: note: previous definition is here
typedef struct ICPState ICPState;
^
Work around the problems by including the proper headers in spapr.h
and by using struct forward declarations in cpu.h.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When compiling with Clang in -std=gnu99 mode, there is a warning/error:
CC ppc64-softmmu/hw/intc/xics_spapr.o
In file included from /home/thuth/devel/qemu/hw/intc/xics_spapr.c:34:
/home/thuth/devel/qemu/include/hw/ppc/xics.h:203:34: error: redefinition of typedef 'sPAPRMachineState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct sPAPRMachineState sPAPRMachineState;
^
/home/thuth/devel/qemu/include/hw/ppc/spapr_irq.h:25:34: note: previous definition is here
typedef struct sPAPRMachineState sPAPRMachineState;
^
We have to remove the duplicated typedef here and include "spapr.h" instead.
But "spapr.h" should not be included for the pnv machine files. So move
the spapr-related prototypes into a new file called "xics_spapr.h" instead.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Header files requiring MouseTransformInfo already include "ui/console.h".
To clean "qemu/typedefs.h", move the declaration to "ui/console.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring PCMachineClass already include "hw/i386/pc.h".
To clean "qemu/typedefs.h", move the declaration to "hw/i386/pc.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring SerialState already include "hw/char/serial.h".
To clean "qemu/typedefs.h", move the declaration to "hw/char/serial.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring SMBusDevice already include "hw/i2c/smbus.h".
To clean "qemu/typedefs.h", move the forward declaration
to "hw/i2c/smbus.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring AllwinnerAHCIState already include "hw/ide/ahci.h".
To clean "qemu/typedefs.h", move the declaration to "hw/ide/ahci.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is only one header file requiring this typedef (hw/arm/pxa.h),
let it include "hw/pcmcia.h" directly to simplify "qemu/typedefs.h".
To clean "qemu/typedefs.h", move the declaration to "hw/pcmcia.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[thuth: slightly tweaked commit message]
Signed-off-by: Thomas Huth <thuth@redhat.com>
PS2State is only used in "hw/input/ps2.h", there is no
need to expose it via "qemu/typedefs.h".
To clean "qemu/typedefs.h", move the forward declaration
to "hw/input/ps2.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcQfb3AAoJENSXKoln91plXOkH/Rb+3IUi3ziXLaIo18fvMYcO
PY4cT/+3Lv9a8aa3/L1QFEYjI8Mu5s8MCQbQbOckifnusPao4bCHrVzhnwrchelb
DnkccwJcbyMkPAB2EqsUDNIRLiA6EmaXu4d9ve8HEo4mB3uy/OcOUo6YtotaPuV6
Z9kAyS1lnXOkrlbWU0ZgmEvvw8Mhs/XED3HOtzPpfrOVKnpObPqdMLPsVLqC761k
LZ6vbrjo2ELBwp+3WVaXDmLrNLF/qXd3NyFKPQ+EI8q3o7+7OpBptXOkuwT9CvAy
NzAMBFAIsKo90C1PD5hzlyYeoaEkyGBR0Uquiz+FkxUr9NuKs40qOEEjwd5njPg=
=q6sK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/amarkovic/tags/mips-queue-january-17-2019-v2' into staging
MIPS queue for January 17, 2019 - v2
# gpg: Signature made Fri 18 Jan 2019 15:55:35 GMT
# gpg: using RSA key D4972A8967F75A65
# gpg: Good signature from "Aleksandar Markovic <amarkovic@wavecomp.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8526 FBF1 5DA3 811F 4A01 DD75 D497 2A89 67F7 5A65
* remotes/amarkovic/tags/mips-queue-january-17-2019-v2:
target/mips: Introduce 32 R5900 multimedia registers
target/mips: Rename 'rn' to 'register_name'
target/mips: Add CP0 register MemoryMapID
target/mips: Amend preprocessor constants for CP0 registers
target/mips: Update ITU to handle bus errors
target/mips: Update ITU to utilize SAARI and SAAR CP0 registers
target/mips: Add field and R/W access to ITU control register ICR0
target/mips: Provide R/W access to SAARI and SAAR CP0 registers
target/mips: Add fields for SAARI and SAAR CP0 registers
target/mips: Use preprocessor constants for 32 major CP0 registers
target/mips: Add preprocessor constants for 32 major CP0 registers
target/mips: Move comment containing summary of CP0 registers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's report IO-coherent access is supported for translation
table walks, descriptor fetches and queues by setting the COHACC
override flag. Without that, we observe wrong command opcodes.
The DT description also advertises the dma coherency.
Fixes a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20190107101041.765-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update ITU to utilize SAARI and SAAR CP0 registers.
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Add field and R/W access to ITU control register ICR0.
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
GCC 8 added a -Wstringop-truncation warning:
The -Wstringop-truncation warning added in GCC 8.0 via r254630 for
bug 81117 is specifically intended to highlight likely unintended
uses of the strncpy function that truncate the terminating NUL
character from the source string.
This new warning leads to compilation failures:
CC hw/acpi/core.o
In function 'acpi_table_install', inlined from 'acpi_table_add' at qemu/hw/acpi/core.c:296:5:
qemu/hw/acpi/core.c:184:9: error: 'strncpy' specified bound 4 equals destination size [-Werror=stringop-truncation]
strncpy(ext_hdr->sig, hdrs->sig, sizeof ext_hdr->sig);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
make: *** [qemu/rules.mak:69: hw/acpi/core.o] Error 1
Use the QEMU_NONSTRING attribute, since ACPI tables don't require the
strings to be NUL-terminated.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The TPM Physical Presence interface consists of an ACPI part, a shared
memory part, and code in the firmware. Users can send messages to the
firmware by writing a code into the shared memory through invoking the
ACPI code. When a reboot happens, the firmware looks for the code and
acts on it by sending sequences of commands to the TPM.
This patch adds the ACPI code. It is similar to the one in EDK2 but doesn't
assume that SMIs are necessary to use. It uses a similar datastructure for
the shared memory as EDK2 does so that EDK2 and SeaBIOS could both make use
of it. I extended the shared memory data structure with an array of 256
bytes, one for each code that could be implemented. The array contains
flags describing the individual codes. This decouples the ACPI implementation
from the firmware implementation.
The underlying TCG specification is accessible from the following page.
https://trustedcomputinggroup.org/tcg-physical-presence-interface-specification/
This patch implements version 1.30.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André - ACPI code improvements and windows fixes ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid having to hard code the base address of the PPI virtual
memory device we introduce a fw_cfg file etc/tpm/config that holds the
base address of the PPI device, the version of the PPI interface and
the version of the attached TPM.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André: renamed to etc/tpm/config, made it static, document it ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement a virtual memory device for the TPM Physical Presence interface.
The memory is located at 0xFED45000 and used by ACPI to send messages to the
firmware (BIOS) and by the firmware to provide parameters for each one of
the supported codes.
This interface should be used by all TPM devices on x86 and can be
added by calling tpm_ppi_init_io().
Note: bios_linker cannot be used to allocate the PPI memory region,
since the reserved memory should stay stable across reboots, and might
be needed before the ACPI tables are installed.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Making some global properties optional will let us simplify
compat code when a given property works on most (but not all)
subclasses of a given type.
Device types will be able to opt out from optional compat
properties by simply not registering those properties.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit adds implementation of RX packets
coalescing, compatible with requirements of Windows
Hardware compatibility kit.
The device enables feature VIRTIO_NET_F_RSC_EXT in
host features if it supports extended RSC functionality
as defined in the specification.
This feature requires at least one of VIRTIO_NET_F_GUEST_TSO4,
VIRTIO_NET_F_GUEST_TSO6. Windows guest driver acks
this feature only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
is also present.
If the guest driver acks VIRTIO_NET_F_RSC_EXT feature,
the device coalesces TCPv4 and TCPv6 packets (if
respective VIRTIO_NET_F_GUEST_TSO feature is on,
populates extended RSC information in virtio header
and sets VIRTIO_NET_HDR_F_RSC_INFO bit in header flags.
The device does not recalculate checksums in the coalesced
packet, so they are not valid.
In this case:
All the data packets in a tcp connection are cached
to a single buffer in every receive interval, and will
be sent out via a timer, the 'virtio_net_rsc_timeout'
controls the interval, this value may impact the
performance and response time of tcp connection,
50000(50us) is an experience value to gain a performance
improvement, since the whql test sends packets every 100us,
so '300000(300us)' passes the test case, it is the default
value as well, tune it via the command line parameter
'rsc_interval' within 'virtio-net-pci' device, for example,
to launch a guest with interval set as '500000':
'virtio-net-pci,netdev=hostnet1,bus=pci.0,id=net1,mac=00,
guest_rsc_ext=on,rsc_interval=500000'
The timer will only be triggered if the packets pool is not empty,
and it'll drain off all the cached packets.
'NetRscChain' is used to save the segments of IPv4/6 in a
VirtIONet device.
A new segment becomes a 'Candidate' as well as it passed sanity check,
the main handler of TCP includes TCP window update, duplicated
ACK check and the real data coalescing.
An 'Candidate' segment means:
1. Segment is within current window and the sequence is the expected one.
2. 'ACK' of the segment is in the valid window.
Sanity check includes:
1. Incorrect version in IP header
2. An IP options or IP fragment
3. Not a TCP packet
4. Sanity size check to prevent buffer overflow attack.
5. An ECN packet
Even though, there might more cases should be considered such as
ip identification other flags, while it breaks the test because
windows set it to the same even it's not a fragment.
Normally it includes 2 typical ways to handle a TCP control flag,
'bypass' and 'finalize', 'bypass' means should be sent out directly,
while 'finalize' means the packets should also be bypassed, but this
should be done after search for the same connection packets in the
pool and drain all of them out, this is to avoid out of order fragment.
All the 'SYN' packets will be bypassed since this always begin a new'
connection, other flags such 'URG/FIN/RST/CWR/ECE' will trigger a
finalization, because this normally happens upon a connection is going
to be closed, an 'URG' packet also finalize current coalescing unit.
Statistics can be used to monitor the basic coalescing status, the
'out of order' and 'out of window' means how many retransmitting packets,
thus describe the performance intuitively.
Difference between ip v4 and v6 processing:
Fragment length in ipv4 header includes itself, while it's not
included for ipv6, thus means ipv6 can carry a real 65535 payload.
Note that main goal of implementing this feature in software
is to create reference setup for certification tests. In such
setups guest migration is not required, so the coalesced packets
not yet delivered to the guest will be lost in case of migration.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We better stop right away. For now, errors would be partially ignored
(so the guest might get informed or the device might get unplugged),
although actual plug/unplug will be reported as failed to the user.
While at it, properly move the check to the pre_plug handler for the plug
case, as we can test the slot state before the device will be realized.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
xend have been replaced by libxenlight (libxl) for many Xen releases
now.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
It is broken since Xen 4.9 [1] and it will not build in Xen 4.12. Also,
it is not built by default since QEMU 2.6.
[1] https://lists.xenproject.org/archives/html/xen-devel/2018-09/msg00313.html
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
This patch adds create and destroy function for XenBlockDevice-s so that
they can be created automatically when the Xen toolstack instantiates a new
PV backend via xenstore. When the XenBlockDevice is created this way it is
also necessary to create a 'drive' which matches the configuration that the
Xen toolstack has written into xenstore. This is done by formulating the
parameters necessary for each 'blockdev' layer of the drive and then using
qmp_blockdev_add() to create the layers. Also, for compatibility with the
legacy 'xen_disk' implementation, an iothread is automatically created for
the new XenBlockDevice. This, like the driver layers, will be destroyed
after the XenBlockDevice is unrealized.
The legacy backend scan for 'qdisk' is removed by this patch, which makes
the 'xen_disk' code is redundant. The code will be removed by a subsequent
patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...that maintains compatibility with existing Xen toolstacks.
Xen toolstacks instantiate PV backends by simply writing information into
xenstore and expecting a backend implementation to be watching for this.
This patch adds a new 'xen-backend' module to allow individual XenDevice
implementations to register create and destroy functions. The creator
will be called when a tool-stack instantiates a new backend in this way,
and the destructor will then be called after the resulting XenDevice
object is unrealized.
To support this it is also necessary to add new watchers into the XenBus
implementation to handle enumeration of new backends and also destruction
of XenDevice-s when the toolstack sets the backend 'online' key to 0.
NOTE: This patch only adds the framework. A subsequent patch will add a
creator function for xen-block devices.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and wire in the dataplane.
This patch adds the remaining code to make the xen-block XenDevice
functional. The parameters that a block frontend expects to find are
populated in the backend xenstore area, and the 'ring-ref' and
'event-channel' values specified in the frontend xenstore area are
mapped/bound and used to set up the dataplane.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The legacy PV backend infrastructure provides functions to bind, unbind
and send notifications to event channnels. Similar functionality will be
required by XenDevice implementations so this patch adds the necessary
support.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Patch squashed with:
Patch "xen: add event channel interface for XenDevice-s" makes use of
the type xenevtchn_port_or_error_t, but this isn't avaiable before Xen
4.7. Also the function xen_device_bind_event_channel assign the return
value of xenevtchn_bind_interdomain to channel->local_port but check the
result for error with xendev->local_port.
Fix by:
- removing local_port from struct XenDevice as it isn't use anywere.
- adding a compatibility typedef for xenevtchn_port_or_error_t for Xen
4.6 and earlier.
As extra, replace the type of XenEventChannel->local_port by
evtchn_port_t.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
The legacy PV backend infrastructure provides functions to map, unmap and
copy pages granted by frontends. Similar functionality will be required
by XenDevice implementations so this patch adds the necessary support.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
A Xen PV frontend communicates its state to the PV backend by writing to
the 'state' key in the frontend area in xenstore. It is therefore
necessary for a XenDevice implementation to be notified whenever the
value of this key changes.
This patch adds code to do this as follows:
- an 'fd handler' is registered on the libxenstore handle which will be
triggered whenever a 'watch' event occurs
- primitives are added to xen-bus-helper to add or remove watch events
- a list of Notifier objects is added to XenBus to provide a mechanism
to call the appropriate 'watch handler' when its associated event
occurs
The xen-block implementation is extended with a 'frontend_changed' method,
which calls as-yet stub 'connect' and 'disconnect' functions when the
relevant frontend state transitions occur. A subsequent patch will supply
a full implementation for these functions.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds a new source module, xen-bus-helper.c, which builds on
basic libxenstore primitives to provide functions to create (setting
permissions appropriately) and destroy xenstore areas, and functions to
'printf' and 'scanf' nodes therein. The main xen-bus code then uses
these primitives [1] to initialize and destroy the frontend and backend
areas for a XenDevice during realize and unrealize respectively.
The 'xen-block' implementation is extended with a 'get_name' method that
returns the VBD number. This number is required to 'name' the xenstore
areas.
NOTE: An exit handler is also added to make sure the xenstore areas are
cleaned up if QEMU terminates without devices being unrealized.
[1] The 'scanf' functions are actually not yet needed, but they will be
needed by code delivered in subsequent patches.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds new XenDevice-s: 'xen-disk' and 'xen-cdrom', both derived
from a common 'xen-block' parent type. These will eventually replace the
'xen_disk' (note the underscore rather than hyphen) legacy PV backend but
it is illustrative to build up the implementation incrementally, along with
the XenBus/XenDevice framework. Subsequent patches will therefore add to
these devices' implementation as new features are added to the framework.
After this patch has been applied it is possible to instantiate new
'xen-disk' or 'xen-cdrom' devices with a single 'vdev' parameter, which
accepts values adhering to the Xen VBD naming scheme [1]. For example, a
command-line instantiation of a xen-disk can be done with an argument
similar to the following:
-device xen-disk,vdev=hda
The implementation of the vdev parameter formulates the appropriate VBD
number for use in the PV protocol.
[1] https://xenbits.xen.org/docs/unstable/man/xen-vbd-interface.7.html
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds the basic boilerplate for a 'XenBus' object that will act
as a parent to 'XenDevice' PV backends.
A new 'XenBridge' object is also added to connect XenBus to the system bus.
The XenBus object is instantiated by a new xen_bus_init() function called
from the same sites as the legacy xen_be_init() function.
Subsequent patches will flesh-out the functionality of these objects.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and xen_backend.h to xen-legacy-backend.h
Rather than attempting to convert the existing backend infrastructure to
be QOM compliant (which would be hard to do in an incremental fashion),
subsequent patches will introduce a completely new framework for Xen PV
backends. Hence it is necessary to re-name parts of existing code to avoid
name clashes. The re-named 'legacy' infrastructure will be removed once all
backends have been ported to the new framework.
This patch is purely cosmetic. No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcOKyMAAoJEL/70l94x66DxKEH/1ho2Xl8ezxCecA6q3HqTgMT
NJ/ntdqQwVwekKOWzsywnM3/LkEDLH55MxbTeQ8M/Vb1seS8eROz24/gPTzvFrfR
n/d11rDV1EJfWe0H7nGLLFiRv0MSjxLpG9c3dlOKWhwOYHm25tr48PsdfVFP9Slz
BK3rwrMeDgArfptHAIsAXt2h1S0EzrG9pMwGDpErCDzziXxBhUESE0Iqfw8LsH1K
VjMn6rn7Ts1XKlxxwsm+BzHlTJghbj3tWPIfk+6uK2isP4iM3gFCoav3SG9XVXof
V9+vFyMxdtZKT/0HvajhUS4/1S/uGBNNchZRnCxXlpbueWc5ROtvarhM6Hb0eck=
=i8E5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* HAX support for Linux hosts (Alejandro)
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
# gpg: Signature made Fri 11 Jan 2019 14:47:40 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (34 commits)
avoid TABs in files that only contain a few
remove space-tab sequences
scripts: add script to convert multiline comments into 4-line format
hw/watchdog/wdt_i6300esb: remove a unnecessary comment
checkpatch: warn about qemu/queue.h head structs that are not typedef-ed
qemu/queue.h: simplify reverse access to QTAILQ
qemu/queue.h: reimplement QTAILQ without pointer-to-pointers
qemu/queue.h: remove Q_TAILQ_{HEAD,ENTRY}
qemu/queue.h: typedef QTAILQ heads
qemu/queue.h: leave head structs anonymous unless necessary
vfio: make vfio_address_spaces static
qemu/queue.h: do not access tqe_prev directly
test: replace gtester with a TAP driver
test: execute g_test_run when tests are skipped
qga: drop < Vista compatibility
build-sys: build with Vista API by default
build-sys: move windows defines in osdep.h header
build-sys: don't include windows.h, osdep.h does it
scsi: esp: Defer command completion until previous interrupts have been handled
esp-pci: Fix status register write erase control
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are not many, and they are all simple mistakes that ended up
being committed. Remove them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-2-pbonzini@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be needed when we change the QTAILQ head and elem structs
to unions. However, it is also consistent with the usage elsewhere
in QEMU for other list head structs (see for example FsMountList).
Note that most QTAILQs only need their name in order to do backwards
walks. Those do not break with the struct->union change, and anyway
the change will also remove the need to name heads when doing backwards
walks, so those are not touched here.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is not used outside hw/vfio/common.c, so it does not need to
be extern.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of verbose arrays with 4 lines for each entry, make each
entry take only one line. This makes long arrays that couldn't
fit in the screen become short and readable.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-4-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro is only used in one place, where the purpose of the
value is obvious. Eliminate the macro so we don't need to rely
on stringify().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-2-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make them more QOMConventional.
Cc:qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190105023831.66910-1-liq3ea@163.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Depending on the interrupt mode of the machine, enable or disable the
XIVE MMIOs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'dual' sPAPR IRQ backend supports both interrupt mode, XIVE
exploitation mode and the legacy compatibility mode (XICS). both modes
are not supported at the same time.
The machine starts with the legacy mode and a new interrupt mode can
then be negotiated by the CAS process. In this case, the new mode is
activated after a reset to take into account the required changes in
the machine. These impact the device tree layout, the interrupt
presenter object and the exposed MMIO regions in the case of XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
commit 15ed653fa4 ("ppc/xics: An ICS with offset 0 is assumed to be
uninitialized") introduced an extra check on the ICS offset which is
not strictly necessary.
Revert the change to be able to map the XICS IRQ number space on the
XIVE IRQ number space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu_irq array is now allocated at the machine level using a sPAPR
IRQ set_irq handler depending on the chosen interrupt mode. The use of
this handler is slightly inefficient today but it will become necessary
when the 'dual' interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Future changes of the ICSState object will remove the qemu_irq array
from under the interrupt controller model. Prepare ground for the PSI
interrupt sources and introduce a new one directly under the PSI
device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support the 'dual' interrupt mode, XICS and XIVE, we plan to move
the qemu_irq array of each interrupt controller under the machine and
do the allocation under the sPAPR IRQ init method.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the interrupt presenter is linked to a CPU using the
cpu_intc_create() method of the sPAPR IRQ backend. The resulting
object is assigned to the PowerPCCPU 'intc' pointer whatever the
interrupt mode, XICS or XIVE.
To support the 'dual' interrupt mode, we will need to distinguish
between the two presenter objects and for that, we plan to introduce a
second interrupt presenter object pointer under the PowerPCCPU. The
modifications below move the assignment of the presenter object under
the cpu_intc_create() method to prepare ground for the future changes.
Both sPAPR and PowerNV machines are impacted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qirq routines of the XiveSource and the sPAPRXive model are only
used under the sPAPR IRQ backend. Simplify the overall call stack and
gather all the code under spapr_qirq_xive(). It will ease future
changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PHB hotplug will bring more users for it. Let's define it along with
the PHB defines from which it is derived for simplicity.
While here fix a misleading comment about manual placement, which was
abandoned with 30b3bc5aa9.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This adds cleanup counterparts to pci_register_root_bus(),
pci_root_bus_new(), and pci_bus_irqs().
These cleanup routines are needed in the case of hotpluggable
PCIHostBridge implementations. Currently we can rely on the
object_unparent()'ing of the PCIHostState recursively unparenting
and cleaning up it's child buses, but we need explicit calls
to also:
1) remove the PCIHostState from pci_host_bridges global list.
otherwise, we risk accessing freed memory when we access
the list later
2) clean up memory allocated in pci_bus_irqs()
Both are handled outside the context of any particular bus or
host bridge's init/realize functions, making it difficult to
avoid the need for explicit cleanup functions without remodeling
how PCIHostBridges are created. So keep it simple and just add
them for now.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only used when creating the default PHB. Let's rename
it and move it to the core machine code for clarity.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SLOF receives a device tree and updates it with various properties
before switching to the guest kernel and QEMU is not aware of any changes
made by SLOF. Since there is no real RTAS (QEMU implements it), it makes
sense to pass the SLOF final device tree to QEMU to let it implement
RTAS related tasks better, such as PCI host bus adapter hotplug.
Specifially, now QEMU can find out the actual XICS phandle (for PHB
hotplug) and the RTAS linux,rtas-entry/base properties (for firmware
assisted NMI - FWNMI).
This stores the initial DT blob in the sPAPR machine and replaces it
in the KVMPPC_H_UPDATE_DT (new private hypercall) handler.
This adds an @update_dt_enabled machine property to allow backward
migration.
SLOF already has a hypercall since
https://github.com/aik/SLOF/commit/e6fc84652c9c0073f9183
This makes use of the new fdt_check_full() helper. In order to allow
the configure script to pick the correct DTC version, this adjusts
the DTC presense test.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
H_HOME_NODE_ASSOCIATIVITY H-Call returns the associativity domain
designation associated with the identifier input parameter
This fixes a crash when we try to hotplug a CPU in memory-less and
CPU-less numa node. In this case, the kernel tries to online the
node, but without the information provided by this h-call, the node id,
it cannot and the CPU is started while the node is not onlined.
It also removes the warning message from the kernel:
VPHN is not supported. Disabling polling..
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only needed when Q35 is in use. Moving it to
the same file that uses it lets you disable the entire USB
subsystem in x86_64-softmmu.mak; of course doing that will
cause -usb to break horribly, but one thing at a time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1545064358-4601-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x1jv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190107' into staging
target-arm queue:
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
# gpg: Signature made Mon 07 Jan 2019 16:29:52 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190107: (37 commits)
Support u-boot noload images for arm as used by, NetBSD/evbarm GENERIC kernel.
hw/misc/tz-mpc: Fix value of BLK_MAX register
target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
arm: Add Clock peripheral stub to NRF51 SOC
tests/microbit-test: Add Tests for nRF51 Timer
arm: Instantiate NRF51 Timers
hw/timer/nrf51_timer: Add nRF51 Timer peripheral
tests/microbit-test: Add Tests for nRF51 GPIO
arm: Instantiate NRF51 general purpose I/O
hw/gpio/nrf51_gpio: Add nRF51 GPIO peripheral
arm: Instantiate NRF51 random number generator
hw/misc/nrf51_rng: Add NRF51 random number generator peripheral
arm: Add header to host common definition for nRF51 SOC peripherals
qtest: Add set_irq_in command to set IRQ/GPIO level
hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
cpus.c: Fix race condition in cpu_stop_current()
MAINTAINERS: Add ARM-related files for hw/[misc|input|timer]/
hw/arm: versal: Plug memory leaks
Revert "armv7m: Guard against no -kernel argument"
arm/xlnx-zynqmp: put APUs and RPUs in separate CPU clusters
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
noload kernels are loaded with the u-boot image header and as a result
the header size needs adding to the entry point. Fake up a hdr so the
kernel image is loaded at the right address and the entry point is
adjusted appropriately.
The default location for the uboot file is 32MiB above bottom of DRAM.
This matches the recommendation in Documentation/arm/Booting.
Clarify the load_uimage API to state the passing of a load address when an
image doesn't specify one, or when loading a ramdisk is expected.
Adjust callers of load_uimage, etc.
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Message-id: 11488a08-1fe0-a278-2210-deb64731107f@gmx.co.uk
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This stubs enables the microbit-micropython firmware to run
on the microbit machine.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-12-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds a model of the nRF51 GPIO peripheral.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
The nRF51 series microcontrollers support up to 32 GPIO pins in various configurations.
The pins can be used as input pins with pull-ups or pull-down.
Furthermore, three different output driver modes per level are
available (disconnected, standard, high-current).
The GPIO-Peripheral has a mechanism for detecting level changes which is
not featured in this model.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use RNG in SOC.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-5-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the NRF51 random number generator peripheral.
This is a simple random generator that continuously generates
new random values after startup.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-4-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a header that provides definitions that are used
across nRF51 peripherals
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-3-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "A10 User Manual V1.20" p.29: "3.2. Memory Mapping" and:
7. System Control
7.1. Overview
A10 embeds a high-speed SRAM which has been split into five segments.
See detailed memory mapping in following table:
Area Address Size (Bytes)
A1 0x00000000-0x00003FFF 16K
A2 0x00004000-0x00007FFF 16K
A3 0x00008000-0x0000B3FF 13K
A4 0x0000B400-0x0000BFFF 3K
Since for emulation purpose we don't need the segmentations, we simply define
the 'A' area as a single 48KB SRAM.
We don't implement the following others areas:
- 'B': 'Secure RAM' (64K),
- 'C': Debug/ISP SRAM
- 'D': USB SRAM
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-000000000000bfff (prio 0, ram): sram A
0000000001c00000-0000000001c00fff (prio -1000, i/o): a10-sram-ctrl
0000000001c0b000-0000000001c0bfff (prio 0, i/o): aw_emac
0000000001c18000-0000000001c18fff (prio 0, i/o): ahci
0000000001c18080-0000000001c180ff (prio 0, i/o): allwinner-ahci
0000000001c20400-0000000001c207ff (prio 0, i/o): allwinner-a10-pic
0000000001c20c00-0000000001c20fff (prio 0, i/o): allwinner-A10-timer
0000000001c28000-0000000001c2801f (prio 0, i/o): serial
0000000040000000-0000000047ffffff (prio 0, ram): cubieboard.ram
Reported-by: Charlie Smurthwaite <charlie@atech.media>
Tested-by: Charlie Smurthwaite <charlie@atech.media>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190104142921.878-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two separate CPU clusters for APUs and RPUs.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181207090135.7651-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds the cpu-cluster type. It aims at gathering CPUs from
the same cluster in a machine.
For now it only has a `cluster-id` property.
Documentation in cluster.h written with the help of Peter Maydell.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181207090135.7651-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All qdev_prop_register_global() set &error_fatal for errp, except
'-rtc driftfix=slew', which arguably should also use &error_fatal, as
otherwise failing to apply the property would only report a warning.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
All globals are now either provided via -global or through -cpu
features (CPU features are implemented by registering globals).
If the global isn't being used, it should warn in either case.
We can thus consider that all global_props are "user-provided"
globals. No need to track this per-globals anymore.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
This will allow to apply compat properties on other objects than QDev easily.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_2() function with pc_compat_2_2_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_3() function with pc_compat_2_3_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Similarly to accel properties, move compat properties out of globals
registration, and apply the machine compat properties during
device_post_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of registering compat properties as globals, let's keep them
in their own array, to avoid mixing with user globals.
Introduce object_apply_global_props() function, to apply compatibility
properties from a GPtrArray.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
-----BEGIN PGP SIGNATURE-----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=BAOm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-3.2-part1' into staging
RISC-V Changes for 3.2, Part 1
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
# gpg: Signature made Fri 21 Dec 2018 16:01:29 GMT
# gpg: using RSA key EF4CA1502CCBAB41
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>"
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-3.2-part1:
MAINTAINERS: Mark RISC-V as Supported
riscv/cpu: use device_class_set_parent_realize
target/riscv/pmp.c: Fix pmp_decode_napot()
sifive_uart: Implement interrupt pending register
RISC-V: Enable second UART on sifive_e and sifive_u
RISC-V: Fix PLIC pending bitfield reads
RISC-V: Fix CLINT timecmp low 32-bit writes
RISC-V: Add hartid and \n to interrupt logging
sifive_u: Set 'clock-frequency' DT property for SiFive UART
sifive_u: Add clock DT node for GEM ethernet
riscv: Enable VGA and PCIE_VGA
hw/riscv/virt: Connect the gpex PCIe
hw/riscv/virt: Adjust memory layout spacing
hw/riscv/virt: Increase the number of interrupts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This pull request supersedes the one from 2018-12-13.
This is a revised first ppc pull request for qemu-4.0. Highlights
are:
* Most of the code for the POWER9 "XIVE" interrupt controller
(not complete yet, but we're getting there)
* A number of g_new vs. g_malloc cleanups
* Some IRQ wiring cleanups
* A fix for how we advertise NUMA nodes to the guest for pseries
-----BEGIN PGP SIGNATURE-----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=IN1s
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20181221' into staging
ppc patch queue 2018-12-21
This pull request supersedes the one from 2018-12-13.
This is a revised first ppc pull request for qemu-4.0. Highlights
are:
* Most of the code for the POWER9 "XIVE" interrupt controller
(not complete yet, but we're getting there)
* A number of g_new vs. g_malloc cleanups
* Some IRQ wiring cleanups
* A fix for how we advertise NUMA nodes to the guest for pseries
# gpg: Signature made Fri 21 Dec 2018 05:34:12 GMT
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20181221: (40 commits)
MAINTAINERS: PPC: add a XIVE section
spapr: change default CPU type to POWER9
spapr: introduce an 'ic-mode' machine option
spapr: add an extra OV5 field to the sPAPR IRQ backend
spapr: add a 'reset' method to the sPAPR IRQ backend
spapr: extend the sPAPR IRQ backend for XICS migration
spapr: allocate the interrupt thread context under the CPU core
spapr: add device tree support for the XIVE exploitation mode
spapr: add hcalls support for the XIVE exploitation interrupt mode
spapr: introduce a new machine IRQ backend for XIVE
spapr-iommu: Always advertise the maximum possible DMA window size
spapr/xive: use the VCPU id as a NVT identifier
spapr/xive: introduce a XIVE interrupt controller
ppc/xive: notify the CPU when the interrupt priority is more privileged
ppc/xive: introduce a simplified XIVE presenter
ppc/xive: introduce the XIVE interrupt thread context
ppc/xive: add support for the END Event State Buffers
Changes requirement for "vsubsbs" instruction
spapr: export and rename the xics_max_server_number() routine
spapr: introduce a spapr_irq_init() routine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcG967AAoJECgfDbjSjVRpUlMH/1wy8WW7Br/4JxlWUPsfZTqZ
0Lg2n59wuFzRVS+gLotp6bUaJGR9xn9fKjI1wfD59oVrDTKyauuw82v0OityEs33
ZquFecuJvP6k5N40DkqA9YJjKSw7nUmLrsyrD0t2H43npikP2aD9f6yootrr3oVV
nPwBvyT9ykIBQc7IzsHDiLw3EPdIf+9IR7+l+PLptzV0zK43Jfwi/nzHIQq00UMz
eLM/ejQLIx4BZJnYGS0Cy6v3K7cS3k45LHDY0cGc0id2jHFN2vdQyHCF9I1ps72q
pSlhMaLEwvQSYyre6iFTG5uuvyIPWv3LOkaBEwMSA5B/HXuEb2RKHThYzS9dc68=
=OwW7
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, features
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 20 Dec 2018 18:26:03 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (44 commits)
x86-iommu: turn on IR by default if proper
x86-iommu: switch intr_supported to OnOffAuto type
q35: set split kernel irqchip as default
pci: Adjust PCI config limit based on bus topology
spapr_pci: perform unplug via the hotplug handler
pci/shpc: perform unplug via the hotplug handler
pci: Reuse pci-bridge hotplug handler handlers for pcie-pci-bridge
pci/pcie: perform unplug via the hotplug handler
pci/pcihp: perform unplug via the hotplug handler
pci/pcihp: overwrite hotplug handler recursively from the start
pci/pcihp: perform check for bus capability in pre_plug handler
s390x/pci: rename hotplug handler callbacks
pci/shpc: rename hotplug handler callbacks
pci/pcie: rename hotplug handler callbacks
hw/i386: Remove deprecated machines pc-0.10 and pc-0.11
hw: acpi: Remove AcpiRsdpDescriptor and fix tests
hw: acpi: Export and share the ARM RSDP build
hw: arm: Support both legacy and current RSDP build
hw: arm: Convert the RSDP build to the buid_append_foo() API
hw: arm: Carry RSDP specific data through AcpiRsdpData
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This option is used to select the interrupt controller mode (XICS or
XIVE) with which the machine will operate. XICS being the default
mode for now.
When running a machine with the XIVE interrupt mode backend, the guest
OS is required to have support for the XIVE exploitation mode. In the
case of legacy OS, the mode selected by CAS should be XICS and the OS
should fail to boot. However, QEMU could possibly detect it, terminate
the boot process and reset to stop in the SLOF firmware. This is not
yet handled.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt modes supported by the hypervisor are advertised to the
guest with new bits definitions of the option vector 5 of property
"ibm,arch-vec-5-platform-support. The byte 23 bits 0-1 of the OV5 are
defined as follow :
0b00 PAPR 2.7 and earlier (Legacy systems)
0b01 XIVE Exploitation mode only
0b10 Either available
If the client/guest selects the XIVE interrupt mode, it informs the
hypervisor by returning the value 0b01 in byte 23 bits 0-1. A 0b00
value indicates the use of the XICS interrupt mode (Legacy systems).
The sPAPR IRQ backend is extended with these definitions and the
values are directly used to populate the "ibm,arch-vec-5-platform-support"
property. The interrupt mode is advertised under TCG and under KVM.
Although a KVM XIVE device is not yet available, the machine can still
operate with kernel_irqchip=off. However, we apply a restriction on
the CPU which is required to be a POWER9 when a XIVE interrupt
controller is in use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the time being, the XIVE reset handler updates the OS CAM line of
the vCPU as it is done under a real hypervisor when a vCPU is
scheduled to run on a HW thread. This will let the XIVE presenter
engine find a match among the NVTs dispatched on the HW threads.
This handler will become even more useful when we introduce the
machine supporting both interrupt modes, XIVE and XICS. In this
machine, the interrupt mode is chosen by the CAS negotiation process
and activated after a reset.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new sPAPR IRQ handler to handle resend after migration
when the machine is using a KVM XICS interrupt controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each interrupt mode has its own specific interrupt presenter object,
that we store under the CPU object, one for XICS and one for XIVE.
Extend the sPAPR IRQ backend with a new handler to support them both.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE interface for the guest is described in the device tree under
the "interrupt-controller" node. A couple of new properties are
specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), for the User level and for the Guest OS
level. Only the Guest OS level is taken into account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the IRQ interrupt number ranges assigned to the guest for the IPIs.
and also under the root node :
- "ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use. OPAL uses the priority 7 queue to automatically
escalate interrupts for all other queues (DD2.X POWER9). So only
priorities [0..6] are allowed for the guest.
Extend the sPAPR IRQ backend with a new handler to populate the DT
with the appropriate "interrupt-controller" node.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The different XIVE virtualization structures (sources and event queues)
are configured with a set of Hypervisor calls :
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (ESB) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification configuration associated
with the queue, only unconditional notification is supported for
the moment. Reset is performed with a queue size of 0 and queueing
is disabled in that case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the guest's internal interrupt structures to their
initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure all notifications
have reached their queue.
Calls that still need to be addressed :
H_INT_SET_OS_REPORTING_LINE
H_INT_GET_OS_REPORTING_LINE
See the code for more documentation on each hcall.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Folded in fix for field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE IRQ backend uses the same layout as the new XICS backend but
covers the full range of the IRQ number space. The IRQ numbers for the
CPU IPIs are allocated at the bottom of this space, below 4K, to
preserve compatibility with XICS which does not use that range.
This should be enough given that the maximum number of CPUs is 1024
for the sPAPR machine under QEMU. For the record, the biggest POWER8
or POWER9 system has a maximum of 1536 HW threads (16 sockets, 192
cores, SMT8).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
sPAPRXive models the XIVE interrupt controller of the sPAPR machine.
It inherits from the XiveRouter and provisions storage for the routing
tables :
- Event Assignment Structure (EAS)
- Event Notification Descriptor (END)
The sPAPRXive model incorporates an internal XiveSource for the IPIs
and for the interrupts of the virtual devices of the guest. This model
is consistent with XIVE architecture which also incorporates an
internal IVSE for IPIs and accelerator interrupts in the IVRE
sub-engine.
The sPAPRXive model exports two memory regions, one for the ESB
trigger and management pages used to control the sources and one for
the TIMA pages. They are mapped by default at the addresses found on
chip 0 of a baremetal system. This is also consistent with the XIVE
architecture which defines a Virtualization Controller BAR for the
internal IVSE ESB pages and a Thread Managment BAR for the TIMA.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Fold in field accessor fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last sub-engine of the XIVE architecture is the Interrupt
Virtualization Presentation Engine (IVPE). On HW, the IVRE and the
IVPE share elements, the Power Bus interface (CQ), the routing table
descriptors, and they can be combined in the same HW logic. We do the
same in QEMU and combine both engines in the XiveRouter for
simplicity.
When the IVRE has completed its job of matching an event source with a
Notification Virtual Target (NVT) to notify, it forwards the event
notification to the IVPE sub-engine. The IVPE scans the thread
interrupt contexts of the Notification Virtual Targets (NVT)
dispatched on the HW processor threads and if a match is found, it
signals the thread. If not, the IVPE escalates the notification to
some other targets and records the notification in a backlog queue.
The IVPE maintains the thread interrupt context state for each of its
NVTs not dispatched on HW processor threads in the Notification
Virtual Target table (NVTT).
The model currently only supports single NVT notifications.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in fix for field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each POWER9 processor chip has a XIVE presenter that can generate four
different exceptions to its threads:
- hypervisor exception,
- O/S exception
- Event-Based Branch (EBB)
- msgsnd (doorbell).
Each exception has a state independent from the others called a Thread
Interrupt Management context. This context is a set of registers which
lets the thread handle priority management and interrupt acknowledgment
among other things. The most important ones being :
- Interrupt Priority Register (PIPR)
- Interrupt Pending Buffer (IPB)
- Current Processor Priority (CPPR)
- Notification Source Register (NSR)
These registers are accessible through a specific MMIO region, called
the Thread Interrupt Management Area (TIMA), four aligned pages, each
exposing a different view of the registers. First page (page address
ending in 0b00) gives access to the entire context and is reserved for
the ring 0 view for the physical thread context. The second (page
address ending in 0b01) is for the hypervisor, ring 1 view. The third
(page address ending in 0b10) is for the operating system, ring 2
view. The fourth (page address ending in 0b11) is for user level, ring
3 view.
The thread interrupt context is modeled with a XiveTCTX object
containing the values of the different exception registers. The TIMA
region is mapped at the same address for each CPU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Event Notification Descriptor (END) XIVE structure also contains
two Event State Buffers providing further coalescing of interrupts,
one for the notification event (ESn) and one for the escalation events
(ESe). A MMIO page is assigned for each to control the EOI through
loads only. Stores are not allowed.
The END ESBs are modeled through an object resembling the 'XiveSource'
It is stateless as the END state bits are backed into the XiveEND
structure under the XiveRouter and the MMIO accesses follow the same
rules as for the XiveSource ESBs.
END ESBs are not supported by the Linux drivers neither on OPAL nor on
sPAPR. Nevetherless, it provides a mean to study the question in the
future and validates a bit more the XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fold in a later fix for field access]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE sPAPR IRQ backend will use it to define the number of ENDs of
the IC controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Initialize the MSI bitmap from it as this will be necessary for the
sPAPR IRQ backend for XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To complete the event routing, the IVRE sub-engine uses a second table
containing Event Notification Descriptor (END) structures.
An END specifies on which Event Queue (EQ) the event notification
data, defined in the associated EAS, should be posted when an
exception occurs. It also defines which Notification Virtual Target
(NVT) should be notified.
The Event Queue is a memory page provided by the O/S defining a
circular buffer, one per server and priority couple, containing Event
Queue entries. These are 4 bytes long, the first bit being a
'generation' bit and the 31 following bits the END Data field. They
are pulled by the O/S when the exception occurs.
The END Data field is a way to set an invariant logical event source
number for an IRQ. On sPAPR machines, it is set with the
H_INT_SET_SOURCE_CONFIG hcall when the EISN flag is used.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fold in a later fix from Cédric fixing field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveRouter models the second sub-engine of the XIVE architecture :
the Interrupt Virtualization Routing Engine (IVRE).
The IVRE handles event notifications of the IVSE and performs the
interrupt routing process. For this purpose, it uses a set of tables
stored in system memory, the first of which being the Event Assignment
Structure (EAS) table.
The EAT associates an interrupt source number with an Event Notification
Descriptor (END) which will be used in a second phase of the routing
process to identify a Notification Virtual Target.
The XiveRouter is an abstract class which needs to be inherited from
to define a storage for the EAT, and other upcoming tables.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in parts of a later fix by Cédric fixing field access]
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveNotifier offers a simple interface, between the XiveSource
object and the main interrupt controller of the machine. It will
forward event notifications to the XIVE Interrupt Virtualization
Routing Engine (IVRE).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Adjust type name string for XiveNotifier]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'sent' status of the LSI interrupt source is modeled with the 'P'
bit of the ESB and the assertion status of the source is maintained
with an extra bit under the main XiveSource object. The type of the
source is stored in the same array for practical reasons.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The first sub-engine of the overall XIVE architecture is the Interrupt
Virtualization Source Engine (IVSE). An IVSE can be integrated into
another logic, like in a PCI PHB or in the main interrupt controller
to manage IPIs.
Each IVSE instance is associated with an Event State Buffer (ESB) that
contains a two bit state entry for each possible event source. When an
event is signaled to the IVSE, by MMIO or some other means, the
associated interrupt state bits are fetched from the ESB and
modified. Depending on the resulting ESB state, the event is forwarded
to the IVRE sub-engine of the controller doing the routing.
Each supported ESB entry is associated with either a single or a
even/odd pair of pages which provides commands to manage the source:
to EOI, to turn off the source for instance.
On a sPAPR machine, the O/S will obtain the page address of the ESB
entry associated with a source and its characteristic using the
H_INT_GET_SOURCE_INFO hcall. On PowerNV, a similar OPAL call is used.
The xive_source_notify() routine is in charge forwarding the source
event notification to the routing engine. It will be filled later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OpenPIC have 5 outputs per connected CPU. The machine init code hence
needs a bi-dimensional array (smp_cpu lines, 5 columns) to wire up the irqs
between the PIC and the CPUs.
The current code first allocates an array of smp_cpus pointers to qemu_irq
type, then it allocates another array of smp_cpus * 5 qemu_irq and fills the
first array with pointers to each line of the second array. This is rather
convoluted.
Simplify the logic by introducing a structured type that describes all the
OpenPIC outputs for a single CPU, ie, fixed size of 5 qemu_irq, and only
allocate a smp_cpu sized array of those.
This also allows to use g_new(T, n) instead of g_malloc(sizeof(T) * n)
as recommended in HACKING.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The watermark bits are set in the interrupt pending register according
to the configuration of txcnt and rxcnt in the txctrl and rxctrl
registers.
Since the UART TX does not implement a FIFO, the txwm bit is set as long
as the TX watermark level is greater than zero.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Connect the gpex PCIe device based on the device tree included in the
HiFive Unleashed ROM.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Increase the number of interrupts to match the HiFive Unleashed board.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Switch the intr_supported variable from a boolean to OnOffAuto type so
that we can know whether the user specified it or not. With that
we'll have a chance to help the user to choose more wisely where
possible. Introduce x86_iommu_ir_supported() to mask these changes.
No functional change at all.
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Starting from QEMU 4.0, let's specify "split" as the default value for
kernel-irqchip.
So for QEMU>=4.0 we'll have: allowed=Y,required=N,split=Y
for QEMU<=3.1 we'll have: allowed=Y,required=N,split=N
(omitting all the "kernel_irqchip_" prefix)
Note that this will let the default q35 machine type to depend on
Linux version 4.4 or newer because that's where split irqchip is
introduced in kernel. But it's fine since we're boosting supported
Linux version for QEMU 4.0 to around Linux 4.5. For more information
please refer to the discussion on AMD's RDTSCP:
https://lore.kernel.org/lkml/20181210181328.GA762@zn.tnic/
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These functions are essentially the same, we only have to use
object_get_typename() for reporting errors. So let's share the
implementation of hotplug handler callbacks.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Perform the check in the pre_plug handler. In addition, we need the
capability only if the device is actually hotplugged (and not created
during machine initialization). This is a preparation for coldplugging
pci devices via that hotplug handler.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename shpc_device_hotplug_common() to
shpc_device_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename pcie_cap_slot_hotplug_common() to
pcie_cap_slot_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The only remaining AcpiRsdpDescriptor users are the ACPI utils for the
BIOS table tests.
We remove that dependency and can thus remove the structure itself.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since "s390x/tcg: avoid overflows in time2tod/tod2time", the
time2tod() function tries to deal with the 9 uppermost bits in the
time value, but uses the wrong mask for this: 0xff80000000000000 should
be used instead of 0xff10000000000000 here.
Fixes: 14055ce53c
Cc: qemu-stable@nongnu.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1544792887-14575-1-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[CH: tweaked commit message]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Now that build_rsdp() supports building both legacy and current RSDP
tables, we can move it to a generic folder (hw/acpi) and have the i386
ACPI code reuse it in order to reduce code duplication.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
That will allow us to generalize the ARM build_rsdp() routine to support
both legacy RSDP (The current i386 implementation) and extended RSDP
(The ARM implementation).
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support DMA read/write draining should be easy for existing VT-d
emulation since the emulation itself does not have any request queue
there so we don't need to do anything to flush the un-commited queue.
What we need to do is to declare the support.
These capabilities are required to pass Windows SVVP test program. It
is verified that when with parameters "x-aw-bits=48,caching-mode=off"
we can pass the Windows SVVP test with this patch applied. Otherwise
we'll fail with:
IOMMU[0] - DWD (DMA write draining) not supported
IOMMU[0] - DWD (DMA read draining) not supported
Segment 0 has no DMA remapping capable IOMMU units
However since these bits are not declared support for QEMU<=3.1, we'll
need a compatibility bit for it and we turn this on by default only
for QEMU>=4.0.
Please refer to VT-d spec 6.5.4 for more information.
CC: Yu Wang <wyu@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1654550
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change the default speed and width for new machine types to the
fastest and widest currently supported. This should be compatible to
the PCIe 4.0 spec. Pre-QEMU-4.0 machine types remain at 2.5GT/s, x1
width.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add fields allowing the PCIe link speed and width of a PCIESlot to
be configured, with an instance_post_init callback on the root port
parent class to set defaults. This allows child classes to set these
via properties or via their own instance_init callback, without
requiring all implementions to support arbitrary user selected values.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Create properties to be able to define speeds and widths for PCIe
links. The only tricky bit here is that our get and set callbacks
translate from the fixed QAPI automagic enums to those we define
in PCI code to represent the actual register segment value.
Cc: Eric Blake <eblake@redhat.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCIe link speed and width between a downstream device and its
upstream port is negotiated on real hardware and susceptible to
dynamic changes due to signal issues and power management. In the
emulated device case there is no real hardware link, but we still
might wish to have some consistency between endpoint and downstream
port via a virtual negotiation. There is of course a real link for
assigned devices and this same virtual negotiation allows the
downstream port to match the endpoint, synchronizing on every read
to support underlying physical hardware dynamically adjusting the
link.
This negotiation is intentionally unidirectional for compatibility.
If the endpoint exceeds the capabilities of the downstream port or
there is no endpoint device, the downstream port reports negotiation
to its maximum speed and width, matching the previous case where
negotiation was absent. De-tuning the endpoint to match a virtual
link doesn't seem to benefit anyone and is a condition we've thus
far reported without functional issues.
Note that PCI_EXP_LNKSTA is already ignored for migration
compatibility via pcie_cap_v1_fill().
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In preparation for reporting higher virtual link speeds and widths,
create enums and macros to help us manage them.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SMBIOS is just another firmware interface used by some QEMU models.
We will later introduce more firmware interfaces in this subdirectory.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All the consumers of "hw/smbios/ipmi.h" are located in hw/smbios/.
There is no need to have this include publicly exposed,
reduce the visibility by moving it in hw/smbios/.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Convert various devices from sysbus init to instance_init
* Remove the now unused sysbus init support entirely
* Allow AArch64 processors to boot from a kernel placed over 4GB
* hw: arm: musicpal: drop TYPE_WM8750 in object_property_set_link()
* versal: minor fixes to virtio-mmio instantation
* arm: Implement the ARMv8.1-HPD extension
* arm: Implement the ARMv8.2-AA32HPD extension
* arm: Implement the ARMv8.1-LOR extension (as the trivial
"no limited ordering regions provided" minimum)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fIbS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20181213' into staging
target-arm queue:
* Convert various devices from sysbus init to instance_init
* Remove the now unused sysbus init support entirely
* Allow AArch64 processors to boot from a kernel placed over 4GB
* hw: arm: musicpal: drop TYPE_WM8750 in object_property_set_link()
* versal: minor fixes to virtio-mmio instantation
* arm: Implement the ARMv8.1-HPD extension
* arm: Implement the ARMv8.2-AA32HPD extension
* arm: Implement the ARMv8.1-LOR extension (as the trivial
"no limited ordering regions provided" minimum)
# gpg: Signature made Thu 13 Dec 2018 14:52:25 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20181213: (37 commits)
target/arm: Implement the ARMv8.1-LOR extension
target/arm: Use arm_hcr_el2_eff more places
target/arm: Introduce arm_hcr_el2_eff
target/arm: Implement the ARMv8.2-AA32HPD extension
target/arm: Implement the ARMv8.1-HPD extension
target/arm: Tidy scr_write
target/arm: Fix HCR_EL2.TGE check in arm_phys_excp_target_el
target/arm: Add SCR_EL3 bits up to ARMv8.5
target/arm: Add HCR_EL2 bits up to ARMv8.5
target/arm: Move id_aa64mmfr* to ARMISARegisters
hw/arm: versal: Correct the nr of IRQs to 192
hw/arm: versal: Use IRQs 111 - 118 for virtio-mmio
hw/arm: versal: Reduce number of virtio-mmio instances
hw/arm: versal: Remove bogus virtio-mmio creation
core/sysbus: remove the SysBusDeviceClass::init path
xen_backend: remove xen_sysdev_init() function
usb/tusb6010: Convert sysbus init function to realize function
timer/puv3_ost: Convert sysbus init function to realize function
timer/grlib_gptimer: Convert sysbus init function to realize function
timer/etraxfs_timer: Convert sysbus init function to realize function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a documentation comment for load_image_size().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-11-peter.maydell@linaro.org
The load_image() function is now no longer used anywhere, so
we can remove it completely. (Use load_image_size() or
g_file_get_contents() instead.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-10-peter.maydell@linaro.org
Currently the load_elf function in elf_ops.h uses
cpu_physical_memory_write() to write the ELF file to
memory if it is not handling it as a ROM blob. This
means we ignore the AddressSpace that the function
is passed to define where it should be loaded.
Use address_space_write() instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181122172653.3413-4-peter.maydell@linaro.org
Correct the nr of IRQs to 192.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181129163655.20370-5-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use IRQs 111 - 118 for virtio-mmio. The interrupts we're currently
using 160+ are not available in the Versal GIC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181129163655.20370-4-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like on other architectures, we should stop the clock while the guest
is not running. This is already properly done for TCG. Right now, doing an
offline migration (stop, migrate, cont) can easily trigger stalls in the
guest.
Even doing a
(hmp) stop
... wait 2 minutes ...
(hmp) cont
will already trigger stalls.
So whenever the guest stops, backup the KVM TOD. When continuing to run
the guest, restore the KVM TOD.
One special case is starting a simple VM: Reading the TOD from KVM to
stop it right away until the guest is actually started means that the
time of any simple VM will already differ to the host time. We can
simply leave the TOD running and the guest won't be able to recognize
it.
For migration, we actually want to keep the TOD stopped until really
starting the guest. To be able to catch most errors, we should however
try to set the TOD in addition to simply storing it. So we can still
catch basic migration problems.
If anything goes wrong while backing up/restoring the TOD, we have to
ignore it (but print a warning). This is then basically a fallback to
old behavior (TOD remains running).
I tested this very basically with an initrd:
1. Start a simple VM. Observed that the TOD is kept running. Old
behavior.
2. Ordinary live migration. Observed that the TOD is temporarily
stopped on the destination when setting the new value and
correctly started when finally starting the guest.
3. Offline live migration. (stop, migrate, cont). Observed that the
TOD will be stopped on the source with the "stop" command. On the
destination, the TOD is temporarily stopped when setting the new
value and correctly started when finally starting the guest via
"cont".
4. Simple stop/cont correctly stops/starts the TOD. (multiple stops
or conts in a row have no effect, so works as expected)
In the future, we might want to send the guest a special kind of time sync
interrupt under some conditions, so it can synchronize its tod to the
host tod. This is interesting for migration scenarios but also when we
get time sync interrupts ourselves. This however will most probably have
to be handled in KVM (e.g. when the tods differ too much) and is not
desired e.g. when debugging the guest (single stepping should not
result in permanent time syncs). I consider something like that an add-on
on top of this basic "don't break the guest" handling.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181130094957.4121-1-david@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Clang 3.4 considers duplicate typedef in ppc4xx_i2c.h and
bitbang_i2c.h an error even if they are identical. Move it to a common
place to allow building with this clang version.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
-----BEGIN PGP SIGNATURE-----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=+od8
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-patches-pull-request' into staging
Trivial patches (2018-12-11)
# gpg: Signature made Tue 11 Dec 2018 18:02:20 GMT
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>"
# gpg: aka "Laurent Vivier <laurent@vivier.eu>"
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>"
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-patches-pull-request: (30 commits)
Fixes i386 xchgq test
maint: Grammar fix to mailmap
MAINTAINERS: Update email address for Fam Zheng
cutils: Assert in-range base for string-to-integer conversions
util: vfio-helpers: use ARRAY_SIZE in qemu_vfio_init_pci()
target: hax: fix errors in comment
MAINTAINERS: Use my work email to review Build and test automation patches
MAINTAINERS: Add a missing entry for the NVDIMM device
MAINTAINERS: Add a missing entry to the QMP section
MAINTAINERS: Add a missing entry to SPICE
MAINTAINERS: Add missing entries for the MPS2 machine
MAINTAINERS: Add missing entries for the Canon DIGIC machine
MAINTAINERS: Add missing entries to the vhost section
MAINTAINERS: Add missing entries to the PC Chipset section
MAINTAINERS: Add a missing entry for the sun4m machines
MAINTAINERS: Add a missing entry for the Old World machines
MAINTAINERS: Add a missing entry for the Xilinx S3A-DSP 1800 machine
MAINTAINERS: Add missing entries for the Jazz machine
MAINTAINERS: Add missing entries for the Xilinx ZynqMP machine
MAINTAINERS: Add a missing entry to the SPARC CPU
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function is only used by a test, move it there.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20181204142023.15982-6-marcandre.lureau@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
global_props is only used for Xen xen_compat_props. It's a static
array of GlobalProperty, like machine globals in SET_MACHINE_COMPAT().
Let's register the globals the same way, without extra copy allocation.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20181204142023.15982-5-marcandre.lureau@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Including all machine types that might have a pcie-root-port.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <154394083644.28192.8501647946108201466.stgit@gimli.home>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
[ehabkost: fixed accidental recursion at spapr_machine_3_1_class_options()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This makes their function more clear and prevents conflicts when adding
the actual devices to the machine state, if necessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181107152434.22219-1-minyard@acm.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add the spapr cap SPAPR_CAP_NESTED_KVM_HV to be used to control the
availability of nested kvm-hv to the level 1 (L1) guest.
Assuming a hypervisor with support enabled an L1 guest can be allowed to
use the kvm-hv module (and thus run it's own kvm-hv guests) by setting:
-machine pseries,cap-nested-hv=true
or disabled with:
-machine pseries,cap-nested-hv=false
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr-rng device is suboptimal when compared to virtio-rng, so
users might want to disable it in their builds. Thus let's introduce
a proper CONFIG switch to allow us to compile QEMU without this device.
The function spapr_rng_populate_dt is required for linking, so move it
to a different location.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Emulation of the block limits VPD page called back into scsi-disk.c,
which however expected the request to be for a SCSIDiskState and
accessed a scsi-generic device outside the bounds of its struct
(namely to retrieve s->max_unmap_size and s->max_io_size).
To avoid this, move the emulation code to a separate function that
takes a new SCSIBlockLimits struct and marshals it into the VPD
response format.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 'q35' machine type implements an Intel Series 3 chipset,
of which there are several variants:
https://www.intel.com/Assets/PDF/datasheet/316966.pdf
The key difference between the 82P35 MCH ('p35', PCI device ID 0x29c0)
and 82Q35 GMCH ('q35', PCI device ID 0x29b0) variants is that the latter
has an integrated graphics adapter. QEMU does not implement integrated
graphics, so uses the PCI ID for the 82P35 chipset, despite calling the
machine type 'q35'. Thus we rename the PCI device ID constant to reflect
reality, to avoid confusing future developers. The new name more closely
matches what pci.ids reports it to be:
$ grep P35 /usr/share/hwdata/pci.ids | grep 29
29c0 82G33/G31/P35/P31 Express DRAM Controller
29c1 82G33/G31/P35/P31 Express PCI Express Root Port
29c4 82G33/G31/P35/P31 Express MEI Controller
29c5 82G33/G31/P35/P31 Express MEI Controller
29c6 82G33/G31/P35/P31 Express PT IDER Controller
29c7 82G33/G31/P35/P31 Express Serial KT Controller
$ grep Q35 /usr/share/hwdata/pci.ids | grep 29
29b0 82Q35 Express DRAM Controller
29b1 82Q35 Express PCI Express Root Port
29b2 82Q35 Express Integrated Graphics Controller
29b3 82Q35 Express Integrated Graphics Controller
29b4 82Q35 Express MEI Controller
29b5 82Q35 Express MEI Controller
29b6 82Q35 Express PT IDER Controller
29b7 82Q35 Express Serial KT Controller
Arguably the QEMU machine type should be named 'p35'. At this point in
time, however, it is not worth the churn for management applications &
documentation to worry about renaming it.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20180830105757.10577-1-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Noted while refactoring:
CC mips-softmmu/hw/mips/gt64xxx_pci.o
In file included from include/hw/pci-host/gt64xxx.h:2,
from hw/mips/gt64xxx_pci.c:30:
include/hw/pci/pci_bus.h:23:5: error: unknown type name ‘PCIIOMMUFunc’
PCIIOMMUFunc iommu_fn;
^~~~~~~~~~~~
include/hw/pci/pci_bus.h:27:5: error: unknown type name ‘pci_set_irq_fn’
pci_set_irq_fn set_irq;
^~~~~~~~~~~~~~
include/hw/pci/pci_bus.h:28:5: error: unknown type name ‘pci_map_irq_fn’
pci_map_irq_fn map_irq;
^~~~~~~~~~~~~~
include/hw/pci/pci_bus.h:29:5: error: unknown type name ‘pci_route_irq_fn’
pci_route_irq_fn route_intx_to_irq;
^~~~~~~~~~~~~~~~
include/hw/pci/pci_bus.h:31:24: error: ‘PCI_SLOT_MAX’ undeclared here (not in a function)
PCIDevice *devices[PCI_SLOT_MAX * PCI_FUNC_MAX];
^~~~~~~~~~~~
include/hw/pci/pci_bus.h:31:39: error: ‘PCI_FUNC_MAX’ undeclared here (not in a function)
PCIDevice *devices[PCI_SLOT_MAX * PCI_FUNC_MAX];
^~~~~~~~~~~~
make[1]: *** [rules.mak:69: hw/mips/gt64xxx_pci.o] Error 1
make: *** [Makefile:482: subdir-mips-softmmu] Error 2
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The vtd_generate_msi_message() in intel-iommu is used to construct a MSI
Message from IRQ. A similar function will be needed when we add interrupt
remapping support in amd-iommu. Moving the function in common file to
avoid the code duplication. Rename it to x86_iommu_irq_to_msi_message().
There is no logic changes in the code flow.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Suggested-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a model of Xilinx Versal SoC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181102131913.1535-2-edgar.iglesias@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wire up nRF51 UART in the corresponding SoC.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not implemented: CTS/NCTS, PSEL*.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As the release document ref below link (page 13):
https://software.intel.com/sites/default/files/managed/c5/15/\
architecture-instruction-set-extensions-programming-reference.pdf
PKU is supported in Skylake Server (Only Server) and later, and
on Intel(R) Xeon(R) Processor Scalable Family. So PKU is supposed
to be in Skylake-Server CPU model. And PKU's CPUID has been
exposed to QEMU. But PKU can't be find in Skylake-Server CPU
model in the code. So this patch will fix this issue in
Skylake-Server CPU model.
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <5014b57f834dcfa8fd3781504d98dcf063d54fde.1540801392.git.tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
(Thank you to Thomas Huth)
v2: fix 32bit build with updated patch (v3) from Philippe Mathieu-Daudé
built in a 32bit debian sid chroot
-----BEGIN PGP SIGNATURE-----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=sHPv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/qemu-trivial-for-3.1-pull-request' into staging
QEMU trivial patches collected between June and October 2018
(Thank you to Thomas Huth)
v2: fix 32bit build with updated patch (v3) from Philippe Mathieu-Daudé
built in a 32bit debian sid chroot
# gpg: Signature made Tue 30 Oct 2018 11:23:01 GMT
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>"
# gpg: aka "Laurent Vivier <laurent@vivier.eu>"
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>"
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/qemu-trivial-for-3.1-pull-request:
milkymist-minimac2: Use qemu_log_mask(GUEST_ERROR) instead of error_report
ppc: move at24c to its own CONFIG_ symbol
hw/intc/gicv3: Remove useless parenthesis around DIV_ROUND_UP macro
hw/pci-host: Remove useless parenthesis around DIV_ROUND_UP macro
tests/bios-tables-test: Remove an useless cast
xen: Use the PCI_DEVICE macro
qobject: Catch another straggler for use of qdict_put_str()
configure: Support pkg-config for zlib
tests: Fix typos in comments and help message (found by codespell)
cpu.h: fix a typo in comment
linux-user: fix comment s/atomic_write/atomic_set/
qemu-iotests: make 218 executable
scripts/qemu.py: remove trailing quotes on docstring
scripts/decodetree.py: remove unused imports
docs/devel/testing.rst: add missing newlines after code block
qemu-iotests: fix filename containing checks
tests/tcg/README: fix location for lm32 tests
memory.h: fix typos in comments
vga_int: remove unused function protype
configs/alpha: Remove unused CONFIG_PARALLEL_ISA switch
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the new memory device functions in place, we can factor out
unplugging of memory devices completely.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-16-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
With the new memory device functions in place, we can factor out
plugging of memory devices completely.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-15-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
With all required memory device class functions in place, we can factor
out pre_plug handling of memory devices. Take proper care of errors. We
still have to carry along legacy_align required for pc compatibility
handling.
We will factor out tracing of the address separately in a follow-up
patch.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-14-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To be able to factor out address assignment of memory devices, we will
have to read (get_addr()) and write (set_addr()) the address.
We can't use properties for this purpose, as properties are device
specific. E.g. while the address property for a DIMM is called "addr", it
might be called differently (e.g. "memaddr") for other devices.
Especially virtio based memory devices cannot use "addr" as that is already
reserved and used for the address on the bus (for the proxy device).
Also, it might be possible to have memory devices without address
properties (e.g. internal DIMM-like thingies).
In contrast to get_addr(), we expect that set_addr() can fail.
Keep it simple for now for pc-dimm and simply set the static property, that
will fail once realized.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-13-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
There are no remaining users of get_region_size() except
memory_device_get_region_size() itself. We can make
memory_device_get_region_size() work directly on get_memory_region()
instead and drop get_region_size().
In addition, we can now use memory_device_get_region_size() in pc-dimm
code to implement get_plugged_size()"
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-12-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The memory region is necessary for plugging/unplugging a memory device.
The region size (via get_region_size()) is no longer sufficient, as
besides the alignment, also the region itself is required in order to
add it to the device memory region of the machine via
- memory_region_add_subregion
- memory_region_del_subregion
So, to factor out plugging/unplugging of memory devices from pc-dimm
code, we have to factor out access to the memory region first.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-11-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We will factor out get_memory_region() from pc-dimm to memory device code
soon. Once that is done, get_region_size() can be implemented
generically and essentially be replaced by
memory_device_get_region_size (and work only on get_memory_region()).
We have some users of get_memory_region() (spapr and pc-dimm code) that are
only interested in the size. So let's rework them to use
memory_device_get_region_size() first, then we can factor out
get_memory_region() and eventually remove get_region_size() without
touching the same code multiple times.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-10-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Document the functions. Don't document get_region_size(), as we will be
dropping/replacing that one soon.
Use same documentation style as in include/exec/memory.h, but don't
document the parameters, as they are self-explanatory.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-9-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's properly forward the errors, so errors from get_region_size() /
get_plugged_size() can be handled.
Users right now call both functions after the device has been realized,
which is will never fail, so it is fine to continue using error_abort.
While at it, remove a leftover error check (suggested by Igor).
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-8-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We're plugging/unplugging a PCDIMMDevice, so directly pass this type
instead of a more generic DeviceState.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181005092024.14344-5-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbzcCHAAoJEDhwtADrkYZT3YsP/2qE4HNY/htj3IP6vNJuSaqw
CLPRTz7zWmUBTE6FqSkvLsq3X2BMFFLeaIPA9EFcbyn2km6qPqBYgg9ElXXvPZBm
6hDeRIoC8FdRD0Apozd5MGC94/lE47PheDRV8V+4KrGLaaMXEPxMZ0wP4AfdS5pS
6Pt2xuF7nPu1+OWVxMk0fXadGjGLEuOQQmTh3B21J5RaynQ3gtd6h7XFC/LJyOGG
LC/6GyPc0h7KU83VnvrRjH/EOpu1wENgrsvWsS0sem8op35Z+i9jU5BfCp4qFkDy
gCHHUEyEeyexS+W+Tj87eBtK2gfrqQx9ovo8CIsWcUwpKbdD6AMK4FKGsDNMNHab
Kg5u/M+O8nHCB7DuursF+3mqEbZHb05cfKe6JEtiq49EuORMV5hp4Ap966noSwTw
UEU0NJNA1p8EdmXVudyyyYR7wpoSSmZpoenA+bJ3nthK8K0KcU4RUGk6ZEbxfJy+
7ENl+3R2IxmxzgXv/x0tz0uFisaVW1rltTXtMte+ElQsO0qy74iHdfR7JHsmLxj9
CO/ABMVoYsWq2OJv8pWLrdKpT4v3HQLJdHhknyu0ZcJGDyICqX29ULLEhPrNEZvW
rxVxAkiemlaqxlUjbrM46CDQQm+w03OCnk7aCYcV4oK+u5+o3mCag705gMPErapZ
6uOE3fAjiWw43sA31mek
=kPZX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-error-2018-10-22' into staging
Error reporting patches for 2018-10-22
# gpg: Signature made Mon 22 Oct 2018 13:20:23 BST
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-error-2018-10-22: (40 commits)
error: Drop bogus "use error_setg() instead" admonitions
vpc: Fail open on bad header checksum
block: Clean up bdrv_img_create()'s error reporting
vl: Simplify call of parse_name()
vl: Fix exit status for -drive format=help
blockdev: Convert drive_new() to Error
vl: Assert drive_new() does not fail in default_drive()
fsdev: Clean up error reporting in qemu_fsdev_add()
spice: Clean up error reporting in add_channel()
tpm: Clean up error reporting in tpm_init_tpmdev()
numa: Clean up error reporting in parse_numa()
vnc: Clean up error reporting in vnc_init_func()
ui: Convert vnc_display_init(), init_keyboard_layout() to Error
ui/keymaps: Fix handling of erroneous include files
vl: Clean up error reporting in device_init_func()
vl: Clean up error reporting in parse_fw_cfg()
vl: Clean up error reporting in mon_init_func()
vl: Clean up error reporting in machine_set_property()
vl: Clean up error reporting in chardev_init_func()
qom: Clean up error reporting in user_creatable_add_opts_foreach()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous commit changed vfio's warning messages from
vfio warning: DEV-NAME: Could not frobnicate
to
warning: vfio DEV-NAME: Could not frobnicate
To match this change, change error messages from
vfio error: DEV-NAME: On fire
to
vfio DEV-NAME: On fire
Note the loss of "error". If we think marking error messages that way
is a good idea, we should mark *all* error messages, i.e. make
error_report() print it.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20181017082702.5581-7-armbru@redhat.com>
The vfio code reports warnings like
error_report(WARN_PREFIX "Could not frobnicate", DEV-NAME);
where WARN_PREFIX is defined so the message comes out as
vfio warning: DEV-NAME: Could not frobnicate
This usage predates the introduction of warn_report() & friends in
commit 97f40301f1. It's time to convert to that interface. Since
these functions already prefix the message with "warning: ", replace
WARN_PREFIX by VFIO_MSG_PREFIX, so the messages come out like
warning: vfio DEV-NAME: Could not frobnicate
The next commit will replace ERR_PREFIX.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-6-armbru@redhat.com>
Add handling of POST_MESSAGE hypercall. For that, add an interface to
regsiter a handler for the messages arrived from the guest on a
particular connection id (IOW set up a message connection in Hyper-V
speak).
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-10-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add handling of SIGNAL_EVENT hypercall. For that, provide an interface
to associate an EventNotifier with an event connection number, so that
it's signaled when the SIGNAL_EVENT hypercall with the matching
connection ID is called by the guest.
Support for using KVM functionality for this will be added in a followup
patch.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-8-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add infrastructure to signal SynIC event flags by atomically setting the
corresponding bit in the event flags page and firing a SINT if
necessary.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-7-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add infrastructure to deliver SynIC messages to the SynIC message page.
Note that KVM may also want to deliver (SynIC timer) messages to the
same message slot.
The problem is that the access to a SynIC message slot is controlled by
the value of its .msg_type field which indicates if the slot is being
owned by the hypervisor (zero) or by the guest (non-zero).
This leaves no room for synchronizing multiple concurrent producers.
The simplest way to deal with this for both KVM and QEMU is to only
deliver messages in the vcpu thread. KVM already does this; this patch
makes it for QEMU, too.
Specifically,
- add a function for posting messages, which only copies the message
into the staging buffer if its free, and schedules a work on the
corresponding vcpu to actually deliver it to the guest slot;
- instead of a sint ack callback, set up the sint route with a message
status callback. This function is called in a bh whenever there are
updates to the message slot status: either the vcpu made definitive
progress delivering the message from the staging buffer (succeeded or
failed) or the guest issued EOM; the status is passed as an argument
to the callback.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-6-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Certain configurations do not allow SynIC to be used in QEMU. In
particular,
- when hyperv_vpindex is off, SINT routes can't be used as they refer to
the destination vCPU by vp_index
- older KVM (which doesn't expose KVM_CAP_HYPERV_SYNIC2) zeroes out
SynIC message and event pages on every msr load, breaking migration
OTOH in-KVM users of SynIC -- SynIC timers -- do work in those
configurations, and we shouldn't stop the guest from using them.
To cover both scenarios, introduce an X86CPU property that makes CPU
init code to skip creation of the SynIC object (and thus disables any
SynIC use in QEMU) but keeps the KVM part of the SynIC working.
The property is clear by default but is set via compat logic for older
machine types.
As a result, when hv_synic and a modern machine type are specified, QEMU
will refuse to run unless vp_index is on and the kernel is recent
enough. OTOH with an older machine type QEMU will run fine with
hv_synic=on against an older kernel and/or without vp_index enabled but
will disallow the in-QEMU uses of SynIC (in e.g. VMBus).
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-4-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make Hyper-V SynIC a device which is attached as a child to a CPU. For
now it only makes SynIC visibile in the qom hierarchy, and maintains its
internal fields in sync with the respecitve msrs of the parent cpu (the
fields will be used in followup patches).
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-3-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A significant part of hyperv.c is not actually tied to x86, and can
be moved to hw/.
This will allow to maintain most of Hyper-V and VMBus
target-independent, and to avoid conflicts with inclusion of
arch-specific headers down the road in VMBus implementation.
Also this stuff can now be opt-out with CONFIG_HYPERV.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082041.29380-4-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some parts of the Hyper-V hypervisor-guest interface appear to be
target-independent, so move them into a proper header.
Not that Hyper-V ARM64 emulation is around the corner but it seems more
conveninent to have most of Hyper-V and VMBus target-independent, and
allows to avoid conflicts with inclusion of arch-specific headers down
the road in VMBus implementation.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082041.29380-2-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When [2] was fixed it was agreed that adding and calling post_plug()
callback after device_reset() was low risk approach to hotfix issue
right before release. So it was merged instead of moving already
existing plug() callback after device_reset() is called which would
be more risky and require all plug() callbacks audit.
Looking at the current plug() callbacks, it doesn't seem that moving
plug() callback after device_reset() is breaking anything, so here
goes agreed upon [3] proper fix which essentially reverts [1][2]
and moves plug() callback after device_reset().
This way devices always comes to plug() stage, after it's been fully
initialized (including being reset), which fixes race condition [2]
without need for an extra post_plug() callback.
1. (25e897881 "qdev: add HotplugHandler->post_plug() callback")
2. (8449bcf94 "virtio-scsi: fix hotplug ->reset() vs event race")
3. https://www.mail-archive.com/qemu-devel@nongnu.org/msg549915.html
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1539696820-273275-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Pierre Morel<pmorel@linux.ibm.com>
Acked-by: Pierre Morel<pmorel@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support for selecting the Memory Region that the GEM
will do DMA to.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181011021931.4249-7-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for extended descriptors with optional 64bit
addressing and timestamping. QEMU will not yet provide
timestamps (always leaving the valid timestamp bit as zero).
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181011021931.4249-6-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add macro with max number of DMA descriptor words.
No functional change.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181011021931.4249-5-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use uint32_t instead of unsigned to describe 32bit descriptor words.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181011021931.4249-4-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now the vfio-platform device has been abstract and could not be
instantiated. The integration of a new vfio platform device required
creating a dummy derived device which only set the compatible string.
Following the few vfio-platform device integrations we have seen the
actual requested adaptation happens on device tree node creation
(sysbus-fdt).
Hence remove the abstract setting, and read the list of compatible
values from sysfs if not set by a derived device.
Update the amd-xgbe and calxeda-xgmac drivers to fill in the number of
compatible values, as there can now be more than one.
Note that sysbus-fdt does not support the instantiation of the
vfio-platform device yet.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
[geert: Rebase, set user_creatable=true, use compatible values in sysfs
instead of user-supplied manufacturer/model options, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
So we have a boot display when using a vgpu as primary display.
ramfb depends on a fw_cfg file. fw_cfg files can not be added and
removed at runtime, therefore a ramfb-enabled vfio device can't be
hotplugged.
Add a nohotplug variant of the vfio-pci device (as child class). Add
the ramfb property to the nohotplug variant only. So to enable the vgpu
display with boot support use this:
-device vfio-pci-nohotplug,display=on,ramfb=on,sysfsdev=...
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This also makes the default display resolution configurable,
via xres and yres properties. The default is 1024x768.
The old code had a hard-coded resolution of 1600x1200.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20181005110837.28209-1-kraxel@redhat.com
Introduces a VFIO based AP device. The device is defined via
the QEMU command line by specifying:
-device vfio-ap,sysfsdev=<path-to-mediated-matrix-device>
There may be only one vfio-ap device configured for a guest.
The mediated matrix device is created by the VFIO AP device
driver by writing a UUID to a sysfs attribute file (see
docs/vfio-ap.txt). The mediated matrix device will be named
after the UUID. Symbolic links to the $uuid are created in
many places, so the path to the mediated matrix device $uuid
can be specified in any of the following ways:
/sys/devices/vfio_ap/matrix/$uuid
/sys/devices/vfio_ap/matrix/mdev_supported_types/vfio_ap-passthrough/devices/$uuid
/sys/bus/mdev/devices/$uuid
/sys/bus/mdev/drivers/vfio_mdev/$uuid
When the vfio-ap device is realized, it acquires and opens the
VFIO iommu group to which the mediated matrix device is
bound. This causes a VFIO group notification event to be
signaled. The vfio_ap device driver's group notification
handler will get called at which time the device driver
will configure the the AP devices to which the guest will
be granted access.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20181010170309.12045-6-akrowiak@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[CH: added missing g_free and device category]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Introduces the base object model for virtualizing AP devices.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Tested-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20181010170309.12045-5-akrowiak@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
"EMU" actually is "Emulex Corporation", so not a good idea to use that
by default. Lets use the Red Hat vendor id instead, which is in line
with the pci ids which are allocated from Red Hat vendor ids too.
Vendor list is available from http://www.uefi.org/pnp_id_list
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20181005091934.12143-1-kraxel@redhat.com
As the kernel has no way of disallowing the start of a huge page
backed VM, we can migrate a running huge backed VM to a host that has
no huge page KVM support.
Let's glue huge page support support to the 3.1 machine, so we do not
migrate to a destination host that doesn't have QEMU huge page support
and can stop migration if KVM doesn't indicate support.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20180928093435.198573-1-frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
struct SubchDev embeds several other structures which are marked with
QEMU_PACKED. This causes the compiler to not care for proper alignment
of these structures. When we later pass around pointers to the unaligned
struct members during migration, this causes problems on host architectures
like Sparc that can not do unaligned memory access.
Most of the structs in ioinst.h are naturally aligned, so we can fix
most of the problem by removing the QEMU_PACKED statements (and use
QEMU_BUILD_BUG_MSG() statements instead to make sure that there is no
padding). However, for the struct SCHIB, we have to keep the QEMU_PACKED
since the compiler adds some padding here otherwise. Move this struct
to the beginning of struct SubchDev instead to fix the alignment problem
here, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1538036615-32542-4-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The uint16_t member cu_type of struct SenseId is not naturally aligned,
and since the struct is marked with QEMU_PACKED, this can lead to
unaligned memory accesses - which does not work on architectures like
Sparc. Thus remove the QEMU_PACKED here and rather copy the struct
byte by byte when we do copy_sense_id_to_guest().
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1538036615-32542-3-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Previously, if the size of initrd >=2G, qemu exits with error:
root@haswell-OptiPlex-9020:/home/lizj# /home/lizhijian/lkp/qemu-colo/x86_64-softmmu/qemu-system-x86_64 -kernel ./vmlinuz-4.16.0-rc4 -initrd large.cgz -nographic
qemu: error reading initrd large.cgz: No such file or directory
root@haswell-OptiPlex-9020:/home/lizj# du -sh large.cgz
2.5G large.cgz
this patch changes the caller side that use this function to calculate
size of initrd file as well.
v2: update error message and int64_t printing format
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Message-Id: <1536833233-14121-1-git-send-email-lizhijian@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create a io region for an EDID data block.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180925075646.25114-4-kraxel@redhat.com
Helper function to figure the size of a edid blob, by checking how many
extensions are present. Both the base edid blob and the extensions are
128 bytes in size.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180925075646.25114-3-kraxel@redhat.com
EDID is a metadata format to describe monitors. On physical hardware
the monitor has an eeprom with that data block which can be read over
i2c bus.
On a linux system you can usually find the EDID data block in
/sys/class/drm/$card/$connector/edid. xorg ships a edid-decode utility
which you can use to turn the blob into readable form.
I think it would be a good idea to use EDID for virtual displays too.
Needs changes in both qemu and guest kms drivers. This patch is the
first step, it adds an generator for EDID blobs to qemu. Comes with a
qemu-edid test tool included.
With EDID we can pass more information to the guest. Names and serial
numbers, so the guests display configuration has no boring "Unknown
Monitor". List of video modes. Display resolution, pretty important
in case we want add HiDPI support some day.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180925075646.25114-2-kraxel@redhat.com
The part of the documentation of DeviceClass that talks about instance_init
is partly wrong: instance_init() functions must not abort or exit, since
the function is also called during introspection of the device already.
So if a device calls exit() during its instance_init() function, QEMU
terminates unexpectedly if somebody tries to just have a look at the
interfaces from the device with "device_add xyz,help" or with the
"device-list-properties" QOM command. This should never happen.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The code looks better, it removes duplicated lines and it will ease
the introduction of common properties for the Aspeed machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In file included from /home/thuth/devel/qemu/hw/timer/aspeed_timer.c:16:
/home/thuth/devel/qemu/include/hw/misc/aspeed_scu.h:37:3: error:
redefinition of typedef 'AspeedSCUState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
} AspeedSCUState;
^
/home/thuth/devel/qemu/include/hw/timer/aspeed_timer.h:27:31: note:
previous definition is here
typedef struct AspeedSCUState AspeedSCUState;
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv2's QEMU interface (sysbus MMIO regions, IRQs,
etc) is now quite complicated with the addition of the
virtualization extensions. Add a comment in the header
file which documents it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180823103818.31189-1-peter.maydell@linaro.org
The nRF51 is a Cortex-M0 microcontroller with an on-board radio module,
plus other common ARM SoC peripherals.
http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
This defines a basic model of the CPU and memory, with no peripherals
implemented at this stage.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180831220920.27113-3-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: wrapped a few long lines]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here are the accumulated ppc target patches for the last several
weeks. Highlights are:
* A number of 40p / PReP cleanups
* Preliminary irq rework on the pseries machine towards the new
XIVE interrupt controller
There are a few patches which make small changes to generic device and
arm code as prerequisites to the 40p interrupt routing cleanup. They
have acks from the relevant maintainers.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEdfRlhq5hpmzETofcbDjKyiDZs5IFAlup3PYACgkQbDjKyiDZ
s5IcYQ//fp79LhIXUKfJuGasVg1K8X795s3nD8vZ76z7FV2kNyHvOCcTsLn0Ccrp
WJLdXdZ0ErY87vJPfHckii9pXOX8J38nV5EFCElSLslx6gCndQZdQX2WY3luwIzq
afiKMERwTkCcqFXXPgweijhhuAU+roay8xdO/ZBO52ogzGaZalTFjG4l9a0DZMSm
ZceDrLrKw6GOaxntLptcn2+Ncuwpm0WSpLyL+bGNAzSAbqdn1dhHQ9UBrcSMteWj
df8J7CX63CFL2MwbQE3RyXeKaomdHabG+QgEVMlS4dpXVUx++ciMtrwZTX1mMDlI
DA9+5u6TcRMz34hN8lWk2O05scOVp8965BcfdeRBYAOTDS4ztiZJ9spKkIV0lHfe
rkgo7F1OsqoQhs9QrLYp0zZYn1OIhHWrbhk/DQptCJMRHk8mct4v2FcyGecU0e1Z
7SlJErxHXmar83PCCJXhtYHthDxN+dTHUW0bbrF4IjysfK+poX5hvvFEjyHGPIJL
duytwgEnnrBOFM7f7mdfH1LKeKzm1ji8nu7g2IsPAXC0xuFaq+d0fZWUWjymSPku
k5k5UUPs8KLtP9XY2qhO0vxBWl5d+CTam19FWVqHjRAp5WqjmoLxWnkofupcT0Yv
LcoHH2Ad9K8e0F4nA4UCYdJwfGH3qO+eBzmBR4+HZOuT1gVvRuw=
=A62f
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180925' into staging
ppc patch queue 2018-09-25
Here are the accumulated ppc target patches for the last several
weeks. Highlights are:
* A number of 40p / PReP cleanups
* Preliminary irq rework on the pseries machine towards the new
XIVE interrupt controller
There are a few patches which make small changes to generic device and
arm code as prerequisites to the 40p interrupt routing cleanup. They
have acks from the relevant maintainers.
# gpg: Signature made Tue 25 Sep 2018 08:00:06 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180925:
40p: add fixed IRQ routing for LSI SCSI device
lsi53c895a: add optional external IRQ via qdev
scsi: remove unused lsi53c895a_create() and lsi53c810_create() functions
scsi: move lsi53c8xx_create() callers to lsi53c8xx_handle_legacy_cmdline()
scsi: add lsi53c8xx_handle_legacy_cmdline() function
sm501: Adjust endianness of pixel value in rectangle fill
spapr_pci: add an extra 'nr_msis' argument to spapr_populate_pci_dt
spapr: increase the size of the IRQ number space
spapr: introduce a spapr_irq class 'nr_msis' attribute
40p: use OR gate to wire up raven PCI interrupts
raven: some minor IRQ-related tidy-ups
hw/ppc: on 40p machine, change default firmware to OpenBIOS
target/ppc/cpu-models: Re-group the 970 CPUs together again
Record history of ppcemb target in common.json
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that these functions are no longer required they can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the function that will soon be used to replace lsi53c895a_create() and
lsi53c810_create().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
So that we don't have to call qdev_get_machine() to get the machine
class and the sPAPRIrq backend holding the number of MSIs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The new layout using static IRQ number does not leave much space to
the dynamic MSI range, only 0x100 IRQ numbers. Increase the total
number of IRQS for newer machines and introduce a legacy XICS backend
for pre-3.1 machines to maintain compatibility.
For the old backend, provide a 'nr_msis' value covering the full IRQ
number space as it does not use the bitmap allocator to allocate MSI
interrupt numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The number of MSI interrupts a sPAPR machine can allocate is in direct
relation with the number of interrupts of the sPAPRIrq backend. Define
statically this value at the sPAPRIrq class level and use it for the
"ibm,pe-total-#msi" property of the sPAPR PHB.
According to the PAPR specs, "ibm,pe-total-#msi" defines the maximum
number of MSIs that are available to the PE. We choose to advertise
the maximum number of MSIs that are available to the machine for
simplicity of the model and to avoid segmenting the MSI interrupt pool
which can be easily shared. If the pool limit is reached, it can be
extended dynamically.
Finally, remove XICS_IRQS_SPAPR which is now unused.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
-----BEGIN PGP SIGNATURE-----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=WnE4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180907' into staging
ppc patch queue 2018-09-07
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
# gpg: Signature made Fri 07 Sep 2018 08:30:02 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180907:
target-ppc: Extend HWCAP2 bits for ISA 3.0
target/ppc/kvm: set vcpu as online/offline
Fix a deadlock case in the CPU hotplug flow
spapr: Correct reference count on spapr-cpu-core
mac_newworld: implement custom FWPathProvider
uninorth: add ofw-addr property to allow correct fw path generation
mac_oldworld: implement custom FWPathProvider
grackle: set device fw_name and address for correct fw path generation
macio: add addr property to macio IDE object
macio: add macio bus to help with fw path generation
macio: move MACIOIDEState type declarations to macio.h
spapr_pci: fix potential NULL pointer dereference
spapr: fix leak of rev array
ppc: Remove deprecated ppcemb target
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAluQU38ACgkQIeENKd+X
cFRAXQgAlhNcwby+Jsk8sbLajMWXEtww9FIv+XESldPOJHmJyCkNDVZX8MuMM7+f
8NraD3YGDJvXP/BEcmyE5yPC6mx+OIi8ufzqP0rUML1x4+Tpxp8nZ7sBH197RtGg
eImPA6oKvg4wyfNOrZ+hGa8HF/iMT03TqeKggUPf3dVAs8LV2iUwBIzrRLB4IhIN
yFnhbcw8cW04tWUhYg4+viDY2k0q7fMrJZkASD/RjGMBjubJkwWvSYOdMIEWSpcG
2qLT5SohzUzHyKPONsoBKjSIP+nKgtyYR6IJh40FDd5S5RRMHe/n3q9jChIkHMma
x1eSNvVd41++QlBKqDeAlA+gbdK/uw==
=FJn/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-pullreq-20180905' into staging
A misc collection of RISC-V related patches for 3.1.
# gpg: Signature made Wed 05 Sep 2018 23:06:55 BST
# gpg: using RSA key 21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-pullreq-20180905:
riscv: remove define cpu_init()
hw/riscv/spike: Set the soc device tree node as a simple-bus
hw/riscv/virtio: Set the soc device tree node as a simple-bus
target/riscv: call gen_goto_tb on DISAS_TOO_MANY
target/riscv: optimize indirect branches
target/riscv: optimize cross-page direct jumps in softmmu
RISC-V: Simplify riscv_cpu_local_irqs_pending
RISC-V: Use atomic_cmpxchg to update PLIC bitmaps
RISC-V: Improve page table walker spec compliance
RISC-V: Update address bits to support sv39 and sv48
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Factor "bus_reserve", "io_reserve", "mem_reserve", "pref32_reserve"
and "pref64_reserve" fields of the "GenPCIERootPort" structure out
to "PCIResReserve" structure, so that other PCI bridges can
reuse it to add resource reserve capability.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
No functional change, just preparation for a followup patch
which needs a VirtIOGPU pointer.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180829122101.29852-2-kraxel@redhat.com>
This reverts commit 93f874fe9d.
Now with virtio-vga being resetted properly the
crash workaround is not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-3-kraxel@redhat.com
We must call the reset functions for both virtio-gpu
and vga to properly reset the combo device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-2-kraxel@redhat.com
This contains the offset of the IDE controller within the macio address space
and is required to allow the address to be included within the fw path.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As the in-built IDE controller is attached to the macio bus then we should also
model this the same in QEMU to aid fw path generation.
Note that all existing macio devices are moved onto the new macio bus so that
the qdev tree accurately reflects the real hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Modify load_elf32()/load_elf64() to treat EM_NANOMIPS as legal as
EM_MIPS is.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
-----BEGIN PGP SIGNATURE-----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=2bke
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/check/20180822' into staging
check/next for 20180822
# gpg: Signature made Wed 22 Aug 2018 09:03:40 BST
# gpg: using RSA key F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/check/20180822:
check: Only test tpm devices when they are compiled in
check: Only test usb-ehci when it is compiled in
check: Only test usb-uhci devices when they are compiled in
check: Only test usb-ohci when it is compiled in
check: Only test nvme when it is compiled in
check: Only test pvpanic when it is compiled in
check: Only test wdt_ib700 when it is compiled in
check: Only test sdhci when it is compiled in
check: Only test i82801b11 when it is compiled in
check: Only test ioh3420 when it is compiled in
check: Only test ipack when it is compiled in
check: Only test hda when it is compiled in
check: Only test ac97 when it is compiled in
check: Only test es1370 when it is compiled in
check: Only test rtl8139 when it is compiled in
check: Only test pcnet when it is compiled in
check: Only test eepro100 when it is compiled in
check: Only test ne2000 when it is compiled in
check: Only test vmxnet3 when it is compiled in
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Validate the config settings that the guest tries to set.
The wiki page documentation is not really accurate here:
generally rather than failing requests to set bad parameters,
the hardware will just clip them to something sensible.
Validate the most important parameters: sizes and
the viewport offsets. This prevents the framebuffer
code from trying to read out-of-range memory.
In the property handling code, we validate the new parameters every
time we encounter a tag that sets them. This means we validate the
config multiple times if the request includes multiple config-setting
tags, but the code would require significant restructuring to do a
validation only once but still return the clipped settings for
get-parameter tags and the buffer allocation tag.
Validation of settings made via the older bcm2835_fb_mbox_push()
function will be done in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-8-peter.maydell@linaro.org
The raspi framebuffir in bcm2835_fb supports the definition
of a virtual "viewport", which is smaller than the full
physical framebuffer size and at an adjustable offset within
it. Only the viewport area is sent to the screen. This allows
the guest to do things like double buffering, or scrolling
by adjusting the viewport origin. Currently QEMU doesn't
implement this at all.
Add support for this feature:
* the property mailbox code needs to distinguish the
virtual width/height from the physical width/height
* the framebuffer code needs to do something with the
virtual width/height/origin information
Note that the wiki documentation on the semantics of the
virtual and physical height and width has it the wrong way
around -- the virtual size is the size of the allocated
buffer, and the physical size is the size of the display,
so the virtual size is always the same as or larger than
the physical.
If the viewport size is set smaller than the physical
screen size, we ignore the viewport settings completely
and just display the physical screen area.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-7-peter.maydell@linaro.org
Abstract out the calculation of the pitch and size of the
framebuffer into functions that operate on the BCM2835FBConfig
struct -- these are about to get a little more complicated
when we add support for virtual and physical sizes differing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-6-peter.maydell@linaro.org
The bcm2835_fb's initial resolution and other parameters are set
via QOM properties. We should reset to those initial values on
device reset, which means we need to save the QOM property
values somewhere that they are not overwritten by guest
changes to the framebuffer configuration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-5-peter.maydell@linaro.org
The BCM2835FBState struct has a 'pitch' field which is a
cached copy of xres * (bpp >> 3), and a 'size' field which is
a cached copy of pitch * yres. However we don't actually do
anything with these fields; delete them. We retain the
now-unused slots in the VMState struct for migration
compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-4-peter.maydell@linaro.org
Refactor the fb property setting code so that rather than
using a set of pointers to local variables to track
whether a config value has been updated in the current
mbox and if so what its new value is, we just copy
all the current settings of the fb at the start, and
then update that copy as we go along, before asking
the fb to switch to it at the end.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-3-peter.maydell@linaro.org
The handling of framebuffer properties in the bcm2835_property code
is a bit clumsy, because for each of the many fb related properties
we try to track the value we're about to set and whether we're going
to be setting a value, and then we hand all the new values off
to the framebuffer via a function which takes them all as separate
arguments. It would be simpler if the property code could easily
copy all the framebuffer's current settings, update them with
the new specified values and then ask the framebuffer to switch
to the new set.
As the first part of this refactoring, pull all the fb config
settings fields in BCM2835FBState out into their own struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-2-peter.maydell@linaro.org
Create a new include file for the pl022's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
While we're adding the new file to MAINTAINERS, add
also the .c file, which was missing an entry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-16-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The IoTKit doesn't have any MSCs itself but it does need
some wiring to connect the external signals from MSCs
in the outer board model up to the registers and the
NVIC IRQ line.
We also need to expose a MemoryRegion corresponding to
the AHB bus, so that MSCs in the outer board model can
use that as their downstream port. (In the FPGA this is
the "AHB Slave Expansion" ports shown in the block
diagram in the AN505 documentation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-14-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The IoTKit does not have any Master Security Contollers itself,
but it does provide registers in the secure privilege control
block which allow control of MSCs in the external system.
Add support for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-13-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Implement a model of the TrustZone Master Securtiy Controller,
as documented in the Arm CoreLink SIE-200 System IP for
Embedded TRM (DDI0571G):
https://developer.arm.com/products/architecture/m-profile/docs/ddi0571/g
The MSC is intended to sit in front of a device which can
be a bus master (eg a DMA controller) and programmably gate
its transactions. This allows a bus-mastering device to be
controlled by non-secure code but still restricted from
making accesses to addresses which are secure-only.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-12-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the system control element's register banks
(sysctl and sysinfo).
This is the last of the previously completely unimplemented
components in the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-11-peter.maydell@linaro.org
Implement the IoTKit system control element's system information
block; this is just a pair of read-only version/config registers,
plus the usual PID/CID ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-10-peter.maydell@linaro.org
The Arm IoTKit includes a system control element which
provides a block of read-only ID registers and a block
of read-write control registers. Implement a minimal
version of this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-9-peter.maydell@linaro.org
The IoTKit has a CMSDK timer device that runs on the S32KCLK.
Create this and wire it up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-8-peter.maydell@linaro.org
The IoTKit includes three different instances of the
CMSDK APB watchdog; create and wire them up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-7-peter.maydell@linaro.org
Now we have a model of the CMSDK dual timer, we can wire it
up in the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-5-peter.maydell@linaro.org
The Arm Cortex-M System Design Kit includes a "dual-input timer module"
which combines two programmable down-counters. Implement a model
of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-4-peter.maydell@linaro.org
In the MPS2 FPGAIO, PSCNTR is a free-running downcounter with
a reload value configured via the PRESCALE register, and
COUNTER counts up by 1 every time PSCNTR reaches zero.
Implement these counters.
We can just increment the counters migration subsection's
version ID because we only added it in the previous commit,
so no released QEMU versions will be using it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-3-peter.maydell@linaro.org
The MPS2 FPGAIO block includes some simple free-running counters.
Implement these.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-2-peter.maydell@linaro.org
* qumu-guest-agent freeze-hook tweak (Christian)
* pm_smbus improvements (Corey)
* Move validation to pre_plug for pc-dimm (David)
* Fix memory leaks (Eduardo, Marc-André)
* synchronization profiler (Emilio)
* Convert the CPU list to RCU (Emilio)
* LSI support for PPR Extended Message (George)
* vhost-scsi support for protection information (Greg)
* Mark mptsas as a storage device in the help (Guenter)
* checkpatch tweak cherry-picked from Linux (me)
* Typos, cleanups and dead-code removal (Julia, Marc-André)
* qemu-pr-helper support for old libmultipath (Murilo)
* Annotate fallthroughs (me)
* MemoryRegionOps cleanup (me, Peter)
* Make s390 qtests independent from libqos, which doesn't actually support it (me)
* Make cpu_get_ticks independent from BQL (me)
* Introspection fixes (Thomas)
* Support QEMU_MODULE_DIR environment variable (ryang)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAlt+5OYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPtxwf8CQM/F+0L+EKeYfYcVgVZsDhhOkLj
Pm61q0bZsWKLby5jCqIDYw7Z/vodJnSS1DO0slIRoXxvQ9DwlkbBnBy/aG/E9U0q
WF1vbCezibDIt7sGcsu9F5zXU9eqe+E6dZfxFrv8FQSOFVxn34TfeJagWLCtzg0d
LnVTF/e4zJD8IQiM7w6lJQxua3fz13ssPEg2KnMkguDhACMwvZ/K/cA2AJkHRMhY
sroPMwLHlrF1NOoeCIrWxYUmSGCRCAy1DmiPGiiSs0yBq/dL0UkAa5Eu6HMQ7rgI
zUff3JDmzEjixUSIEbpVRN+yPCN0/ACSOpJUrKLDxXbc4nZ+PBQ04YpyPQ==
=UZiV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* x86 TCG fixes for 64-bit call gates (Andrew)
* qumu-guest-agent freeze-hook tweak (Christian)
* pm_smbus improvements (Corey)
* Move validation to pre_plug for pc-dimm (David)
* Fix memory leaks (Eduardo, Marc-André)
* synchronization profiler (Emilio)
* Convert the CPU list to RCU (Emilio)
* LSI support for PPR Extended Message (George)
* vhost-scsi support for protection information (Greg)
* Mark mptsas as a storage device in the help (Guenter)
* checkpatch tweak cherry-picked from Linux (me)
* Typos, cleanups and dead-code removal (Julia, Marc-André)
* qemu-pr-helper support for old libmultipath (Murilo)
* Annotate fallthroughs (me)
* MemoryRegionOps cleanup (me, Peter)
* Make s390 qtests independent from libqos, which doesn't actually support it (me)
* Make cpu_get_ticks independent from BQL (me)
* Introspection fixes (Thomas)
* Support QEMU_MODULE_DIR environment variable (ryang)
# gpg: Signature made Thu 23 Aug 2018 17:46:30 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
KVM: cleanup unnecessary #ifdef KVM_CAP_...
target/i386: update MPX flags when CPL changes
i2c: pm_smbus: Add the ability to force block transfer enable
i2c: pm_smbus: Don't delay host status register busy bit when interrupts are enabled
i2c: pm_smbus: Add interrupt handling
i2c: pm_smbus: Add block transfer capability
i2c: pm_smbus: Make the I2C block read command read-only
i2c: pm_smbus: Fix the semantics of block I2C transfers
i2c: pm_smbus: Clean up some style issues
pc-dimm: assign and verify the "addr" property during pre_plug
pc: drop memory region alignment check for 0
util/oslib-win32: indicate alignment for qemu_anon_ram_alloc()
pc-dimm: assign and verify the "slot" property during pre_plug
ipmi: Use proper struct reference for BT vmstate
vhost-scsi: expose 't10_pi' property for VIRTIO_SCSI_F_T10_PI
vhost-scsi: unify vhost-scsi get_features implementations
vhost-user-scsi: move host_features into VHostSCSICommon
cpus: allow cpu_get_ticks out of BQL
cpus: protect TimerState writes with a spinlock
seqlock: add QemuLockable support
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PIIX4 hardware has block transfer buffer always enabled in
the hardware, but the i801 does not. Add a parameter to pm_smbus_init
to force on the block transfer so the PIIX4 handler can enable this
by default, as it was disabled by default before.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-9-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the necessary code so that interrupts actually work from
the pm_smbus device.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-7-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There was no block transfer code in pm_smbus.c, and it is needed
for some devices. So add it.
This adds both byte-by-byte block transfers and buffered block
transfers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-5-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The I2C block transfer commands was not implemented correctly, it
read a length byte and such like it was an smbus transfer.
So fix the smbus_read_block() and smbus_write_block() functions
so they can properly handle I2C transfers, and normal SMBus
transfers (for upcoming changes). Pass in a transfer size and
a bool to know whether to use the size byte (like SMBus) or use
the length given (like I2C).
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-3-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can assign and verify the address before realizing and trying to plug.
reading/writing the address property should never fail for DIMMs, so let's
reduce error handling a bit by using &error_abort. Getting access to the
memory region now might however fail. So forward errors from
get_memory_region() properly.
As all memory devices should use the alignment of the underlying memory
region for guest physical address asignment, do detection of the
alignment in pc_dimm_pre_plug(), but allow pc.c to overwrite the
alignment for compatibility handling.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-5-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can assign and verify the slot before realizing and trying to plug.
reading/writing the slot property should never fail, so let's reduce
error handling a bit by using &error_abort.
To do this during pre_plug, add and use (x86, ppc) pc_dimm_pre_plug().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-2-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for having vhost-scsi also make use of host_features,
move it from struct VHostUserSCSI into struct VHostSCSICommon.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-2-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was not possible to compile out pvpanic. Use the same trick
than applesmc.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
This proposal moves all the related IRQ routines of the sPAPR machine
behind a sPAPR IRQ backend interface 'spapr_irq' to prepare for future
changes. First of which will be to increase the size of the IRQ number
space, then, will follow a new backend for the POWER9 XIVE IRQ controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This proposal introduces a new IRQ number space layout using static
numbers for all devices, depending on a device index, and a bitmap
allocator for the MSI IRQ numbers which are negotiated by the guest at
runtime.
As the VIO device model does not have a device index but a "reg"
property, we introduce a formula to compute an IRQ number from a "reg"
value. It should minimize most of the collisions.
The previous layout is kept in pre-3.1 machines raising the
'legacy_irq_allocation' machine class flag.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last user of the PowerPCCPU typedef in "hw/ppc/xics.h" vanished with
commit b1fd36c363. It isn't necessary to
include "target/ppc/cpu-qom.h" there anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At the moment the PPC64/pseries guest only supports 4K/64K/16M IOMMU
pages and POWER8 CPU supports the exact same set of page size so
so far things worked fine.
However POWER9 supports different set of sizes - 4K/64K/2M/1G and
the last two - 2M and 1G - are not even allowed in the paravirt interface
(RTAS DDW) so we always end up using 64K IOMMU pages, although we could
back guest's 16MB IOMMU pages with 2MB pages on the host.
This stores the supported host IOMMU page sizes in VFIOContainer and uses
this later when creating a new DMA window. This uses the system page size
(64k normally, 2M/16M/1G if hugepages used) as the upper limit of
the IOMMU pagesize.
This changes the type of @pagesize to uint64_t as this is what
memory_region_iommu_get_min_page_size() returns and clz64() takes.
There should be no behavioral changes on platforms other than pseries.
The guest will keep using the IOMMU page size selected by the PHB pagesize
property as this only changes the underlying hardware TCE table
granularity.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This option has been deprecated for two releases; remove it.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Currently our PL080/PL081 model uses a combination of the CPU's
address space (via cpu_physical_memory_{read,write}()) and the
system address space for performing DMA accesses.
For the PL081s in the MPS FPGA images, their DMA accesses
must go via Master Security Controllers. Switch the
PL080/PL081 model to take a MemoryRegion property which
defines its downstream for making DMA accesses.
Since the PL08x are only used in two board models, we
make provision of the 'downstream' link mandatory and convert
both users at once, rather than having it be optional with
a default to the system address space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The PL080 and PL081 have three outgoing interrupt lines:
* DMACINTERR signals DMA errors
* DMACINTTC is the DMA count interrupt
* DMACINTR is a combined interrupt, the logical OR of the other two
We currently only implement DMACINTR, because that's all the
realview and versatile boards needed, but the instances of the
PL081 in the MPS2 firmware images use all three interrupt lines.
Implement the missing DMACINTERR and DMACINTTC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Create a new include file for the pl081's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Arm Cortex-M System Design Kit includes a simple watchdog module
based on a 32-bit down-counter. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The mmio_interface device was a purely internal artifact
of the implementation of the memory subsystem's request_ptr
APIs. Now that we have removed those APIs, we can remove
the mmio_interface device too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Message-id: 20180817114619.22354-4-peter.maydell@linaro.org
Generate an interrupt if USR2_RDR and UCR4_DREN are both set.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Message-id: 1534341354-11956-1-git-send-email-hans-erik.floryd@rt-labs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If a vfio assigned device makes use of a physical IOMMU, then memory
ballooning is necessarily inhibited due to the page pinning, lack of
page level granularity at the IOMMU, and sufficient notifiers to both
remove the page on balloon inflation and add it back on deflation.
However, not all devices are backed by a physical IOMMU. In the case
of mediated devices, if a vendor driver is well synchronized with the
guest driver, such that only pages actively used by the guest driver
are pinned by the host mdev vendor driver, then there should be no
overlap between pages available for the balloon driver and pages
actively in use by the device. Under these conditions, ballooning
should be safe.
vfio-ccw devices are always mediated devices and always operate under
the constraints above. Therefore we can consider all vfio-ccw devices
as balloon compatible.
The situation is far from straightforward with vfio-pci. These
devices can be physical devices with physical IOMMU backing or
mediated devices where it is unknown whether a physical IOMMU is in
use or whether the vendor driver is well synchronized to the working
set of the guest driver. The safest approach is therefore to assume
all vfio-pci devices are incompatible with ballooning, but allow user
opt-in should they have further insight into mediated devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For the older machines (such as Mac and SPARC) the DT nodes representing
bootdevices for disk nodes are irregular for mainly historical reasons.
Since the majority of bootdevice nodes for these machines either do not have a
separate disk node or require different (custom) names then it is much easier
for processing to just disable all suffixes for a particular machine.
Introduce a new ignore_boot_device_suffixes MachineClass property to control
bootdevice suffix generation, defaulting to false in order to preserve
compatibility.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180810124027.10698-1-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will be used to construct a memory region beyond the RAM region
to let firmwares scan the address space with load/store to guess how
much RAM the SoC has.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-7-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fixes the intended protection of read-only values in the
configuration register. They were being always set to zero by mistake.
The read-only fields depend on the configured memory size of the system,
so they cannot be fixed at compile time. The most straight forward
option was to store them in the state structure.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-3-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDMC on the ast2500 has 170 registers.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-2-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds Intel Hexadecimal Object File format support to the
generic loader device. The file format specification is available here:
http://www.piclist.com/techref/fileext/hex/intel.htm
This file format is often used with microcontrollers such as the
micro:bit, Arduino, STM32, etc. Users expect to be able to run .hex
files directly with without first converting them to ELF. Most
micro:bit code is developed in web-based IDEs without direct user access
to binutils so it is important for QEMU to handle this file format
natively.
Signed-off-by: Su Hang <suhang16@mails.ucas.ac.cn>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180814162739.11814-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Image file loaders may add a series of roms. If an error occurs partway
through loading there is no easy way to drop previously added roms.
This patch adds a transaction mechanism that works like this:
rom_transaction_begin();
...call rom_add_*()...
rom_transaction_end(ok);
If ok is false then roms added in this transaction are dropped.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180814162739.11814-5-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some ARM CPUs have bitbanded IO, a memory region that allows convenient
bit access via 32-bit memory loads/stores. This eliminates the need for
read-modify-update instruction sequences.
This patch makes this optional feature an ARMv7MState qdev property,
allowing boards to choose whether they want bitbanding or not.
Status of boards:
* iotkit (Cortex M33), no bitband
* mps2 (Cortex M3), bitband
* msf2 (Cortex M3), bitband
* stellaris (Cortex M3), bitband
* stm32f205 (Cortex M3), bitband
As a side-effect of this patch, Peter Maydell noted that the Ethernet
controller on mps2 board is now accessible. Previously they were hidden
by the bitband region (which does not exist on the real board).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180814162739.11814-2-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reinstates commit b008326744,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Add support for GICv2 virtualization extensions by mapping the necessary
I/O regions and connecting the maintenance IRQ lines.
Declare those additions in the device tree and in the ACPI tables.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-21-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit improve the way the GIC is realized and connected in the
ZynqMP SoC. The security extensions are enabled only if requested in the
machine state. The same goes for the virtualization extensions.
All the GIC to APU CPU(s) IRQ lines are now connected, including FIQ,
vIRQ and vFIQ. The missing CPU to GIC timers IRQ connections are also
added (HYP and SEC timers).
The GIC maintenance IRQs are back-wired to the correct GIC PPIs.
Finally, the MMIO mappings are reworked to take into account the ZynqMP
specifics. The GIC (v)CPU interface is aliased 16 times:
* for the first 0x1000 bytes from 0xf9010000 to 0xf901f000
* for the second 0x1000 bytes from 0xf9020000 to 0xf902f000
Mappings of the virtual interface and virtual CPU interface are mapped
only when virtualization extensions are requested. The
XlnxZynqMPGICRegion struct has been enhanced to be able to catch all
this information.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180727095421.386-20-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the necessary parts of the virtualization extensions state to the
GIC state. We choose to increase the size of the CPU interfaces state to
add space for the vCPU interfaces (the GIC_NCPU_VCPU macro). This way,
we'll be able to reuse most of the CPU interface code for the vCPUs.
The only exception is the APR value, which is stored in h_apr in the
virtual interface state for vCPUs. This is due to some complications
with the GIC VMState, for which we don't want to break backward
compatibility. APRs being stored in 2D arrays, increasing the second
dimension would lead to some ugly VMState description. To avoid
that, we keep it in h_apr for vCPUs.
The vCPUs are numbered from GIC_NCPU to (GIC_NCPU * 2) - 1. The
`gic_is_vcpu` function help to determine if a given CPU id correspond to
a physical CPU or a virtual one.
For the in-kernel KVM VGIC, since the exposed VGIC does not implement
the virtualization extensions, we report an error if the corresponding
property is set to true.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-6-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The differences from ARMv7-M NVIC are:
* ARMv6-M only supports up to 32 external interrupts
(configurable feature already). The ICTR is reserved.
* Active Bit Register is reserved.
* ARMv6-M supports 4 priority levels against 256 in ARMv7-M.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With vga=775 on the Linux command line a first boot of the VM running
Linux works fine. After a warm reboot it crashes during Linux boot.
Before that, valgrind points out bad memory write to console
surface. The VGA code is not aware that virtio-gpu got a message
surface scanout when the display is disabled. Let's reset VGA graphic
mode when it is the case, so that a new display surface is created
when doing further VGA operations.
https://bugs.launchpad.net/qemu/+bug/1784900/
Reported-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Message-id: 20180803153235.4134-1-marcandre.lureau@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MSR_SMI_COUNT started being migrated in QEMU 2.12. Do not migrate it
on older machine types, or the subsection causes a load failure for
guests that use SMM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
aux_create_slave() calls qdev_init_nofail() which in turn "realizes"
the corresponding object. This is unlike qdev_create(), and it is wrong
because qdev_init_nofail() must not be called from an instance_init
function. Move qdev_init_nofail() and the subsequent aux_map_slave into
the caller's realize function.
There are two more bugs that needs to be fixed here, too, where the
objects are created but not added as children. Therefore when
you call object_unparent on them, nothing happens.
In particular dpcd and edid give you an infinite loop in bus_unparent,
because device_unparent is not called and does not remove them from
the list of devices on the bus.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1531745974-17187-17-git-send-email-thuth@redhat.com
[thuth: Added Paolo's fixup for the dpcd and edid unparenting]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A lot of functions are initializing an object and attach it immediately
afterwards to the system bus. Provide a common function for this, which
also uses object_initialize_child() to make sure that the reference
counter is correctly initialized to 1 afterwards.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1531745974-17187-3-git-send-email-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 SoC family changes the runtime behaviour of the hardware
strapping register (SCU70) to write-1-set/write-1-clear, with
write-1-clear implemented on the "read-only" SoC revision register
(SCU7C). For the the AST2400, the hardware strapping is
runtime-configured with read-modify-write semantics.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180709143524.17480-1-andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ->pre_plug() callback is invoked before the device is realized. The
->plug() callback is invoked when the device is being realized but
before it is reset.
This patch adds a ->post_plug() callback which is invoked after the
device has been reset. This callback is needed by HotplugHandlers that
need to wait until after ->reset().
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180716083732.3347-2-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit b008326744.
Hold off removing this for one more QEMU release (current libvirt
release still uses it.)
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
commit b08199c6fb accidentally added a reference to a doc
comment to a nonexistent memory_region_allocate_aux_memory().
This was a leftover from a previous version of the patchset
which defined memory_region_allocate_aux_memory() for
"allocate RAM MemoryRegion and register it for migration"
and left "memory_region_init_ram()" with its original semantics
of "allocate RAM MR but do not register for migration". In
the end we decided on the approach of "memory_region_init_ram()
registers the MR for migration, and memory_region_init_ram_nomigrate()
is a new function which does not", but this comment change
got left in by mistake. Revert that part of the commit.
Reported-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180702130605.13611-1-peter.maydell@linaro.org
The CMSDK timer behaviour is that an interrupt is triggered when the
counter counts down from 1 to 0; however one is not triggered if the
counter is manually set to 0 by a guest write to the counter register.
Currently ptimer can't handle this; add a policy option to allow
a ptimer user to request this behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-2-peter.maydell@linaro.org
smmu_iommu_mr() aims at returning the IOMMUMemoryRegion corresponding
to a given sid. The function extracts both the PCIe bus number and
the devfn to return this data. Current computation of devfn is wrong
as it only returns the PCIe function instead of slot | function.
Fixes 32cfd7f39e ("hw/arm/smmuv3: Cache/invalidate config data")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1530775623-32399-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the Cadence GEM ethernet device. This also requires us to
expose the plic interrupt lines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Instead of creating the interrupt in lines with qemu_allocate_irq() use
qdev_init_gpio_in() as this gives us the ability to use the qdev*gpio*()
helpers later on.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
Create a SiFive Unleashed U54 SoC and use that in the sifive_u machine.
We leave the SoC, RAM, device tree and reset/fdt loading as part of the
machine. All the other device creation has been moved to the SoC.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Here's a last minue pull request before today's soft freeze. Ideally
I would have sent this earlier, but I was waiting for a couple of
extra fixes I knew were close. And the freeze crept up on me, like
always.
Most of the changes here are bugfixes in any case. There are some
cleanups as well, which have been in my staging tree for a little
while. There are a couple of truly new features (some extensions to
the sam460ex platform), but these are low risk, since they only affect
a new and not really stabilized machine type anyway.
Higlights are:
* Mac platform improvements from Mark Cave-Ayland
* Sam460ex improvements from BALATON Zoltan et al.
* XICS interrupt handler cleanups from Cédric Le Goater
* TCG improvements for atomic loads and stores from Richard
Henderson
* Assorted other bugfixes
-----BEGIN PGP SIGNATURE-----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=AHrx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.0-20180703' into staging
ppc patch queue 2018-07-03
Here's a last minue pull request before today's soft freeze. Ideally
I would have sent this earlier, but I was waiting for a couple of
extra fixes I knew were close. And the freeze crept up on me, like
always.
Most of the changes here are bugfixes in any case. There are some
cleanups as well, which have been in my staging tree for a little
while. There are a couple of truly new features (some extensions to
the sam460ex platform), but these are low risk, since they only affect
a new and not really stabilized machine type anyway.
Higlights are:
* Mac platform improvements from Mark Cave-Ayland
* Sam460ex improvements from BALATON Zoltan et al.
* XICS interrupt handler cleanups from Cédric Le Goater
* TCG improvements for atomic loads and stores from Richard
Henderson
* Assorted other bugfixes
# gpg: Signature made Tue 03 Jul 2018 06:55:22 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.0-20180703: (35 commits)
ppc: Include vga cirrus card into the compiling process
target/ppc: Relax reserved bitmask of indexed store instructions
target/ppc: set is_jmp on ppc_tr_breakpoint_check
spapr: compute default value of "hpt-max-page-size" later
target/ppc/kvm: don't pass cpu to kvm_get_smmu_info()
target/ppc/kvm: get rid of kvm_get_fallback_smmu_info()
ppc440_uc: Basic emulation of PPC440 DMA controller
sam460ex: Add RTC device
hw/timer: Add basic M41T80 emulation
ppc4xx_i2c: Rewrite to model hardware more closely
hw/ppc: Give sam46ex its own config option
fpu_helper.c: fix setting FPSCR[FI] bit
target/ppc: Implement the rest of gen_st_atomic
target/ppc: Implement the rest of gen_ld_atomic
target/ppc: Use atomic min/max helpers
target/ppc: Use MO_ALIGN for EXIWX and ECOWX
target/ppc: Split out gen_st_atomic
target/ppc: Split out gen_ld_atomic
target/ppc: Split out gen_load_locked
target/ppc: Tidy gen_conditional_store
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/ppc/spapr.c
Move global_vmstate from vga_common_init() parameter to VGACommonState
field. Set global_vmstate to true for isa vga devices, so nothing
changes here. virtio-vga and secondary-vga already set global_vmstate
to false so no change here either. All other pci vga devices get a new
global-vmstate property, defaulting to false. A compat property flips
it to true for older machine types.
With this in place you don't get a vmstate section naming conflict any
more when adding multiple pci vga devices to your vm.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180702163345.17892-1-kraxel@redhat.com>
Rewrite to make it closer to how real device works so that guest OS
drivers can access I2C devices. Previously this was only a hack to
allow U-Boot to get past accessing SPD EEPROMs but to support other
I2C devices and allow guests to access them we need to model real
device more properly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Just like for the realize handlers, this makes possible to move the
common ICSState code of the reset handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes possible to move the common ICSState code of the realize
handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This changes the ICP realize and reset handlers in DeviceRealize and
DeviceReset handlers. parent handlers are now called from the
inheriting classes which is a cleaner object pattern.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-39-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <20180625124238.25339-35-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20180625124238.25339-33-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now, each CPU has its own TOD. Especially, the TOD will differ
based on creation time of a CPU - e.g. when hotplugging a CPU the times
will differ quite a lot, resulting in stall warnings in the guest.
Let's use a single TOD by implementing our new TOD device. Prepare it
for TOD-clock epoch extension.
Most importantly, whenever we set the TOD, we have to update the CKC
timer.
Introduce "tcg_s390x.h" just like "kvm_s390x.h" for tcg specific
function declarations that should not go into cpu.h.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180627134410.4901-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's treat this like a separate device. TCG will have to store the
actual state/time later on.
Include cpu-qom.h in kvm_s390x.h (due to S390CPU) to compile tod-kvm.c.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180627134410.4901-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The rom_ptr() function allows direct access to the ROM blobs that we
load during startup. However, there are currently no checks for the
size of the accesses, so it's currently possible to crash QEMU for
example with:
$ echo "Insane in the mainframe" > /tmp/test.txt
$ s390x-softmmu/qemu-system-s390x -kernel /tmp/test.txt -append xyz
Segmentation fault (core dumped)
$ s390x-softmmu/qemu-system-s390x -kernel /tmp/test.txt -initrd /tmp/test.txt
Segmentation fault (core dumped)
$ echo -n HdrS > /tmp/hdr.txt
$ sparc64-softmmu/qemu-system-sparc64 -kernel /tmp/hdr.txt -initrd /tmp/hdr.txt
Segmentation fault (core dumped)
We need a possibility to check the size of the ROM area that we want
to access, thus let's add a size parameter to the rom_ptr() function
to avoid these problems.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1530005740-25254-1-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The error handling policy was traditionally set with -drive, but with
-blockdev it is no longer possible to set frontend options. scsi-disk
(and other block devices) have long supported qdev properties to
configure the error handling policy, so let's add these options to
usb-storage as well and just forward them to the internal scsi-disk
instance.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The VPD Block Limits Inquiry page is optional, allowing SCSI devices
to not implement it. This is the case for devices like the MegaRAID
SAS 9361-8i and Microsemi PM8069.
In case of SCSI passthrough, the response of this request is used by
the QEMU SCSI layer to set the max_io_sectors that the guest
device will support, based on the value of the max_sectors_kb that
the device has set in the host at that time. Without this response,
the guest kernel is free to assume any value of max_io_sectors
for the SCSI device. If this value is greater than the value from
the host, SCSI Sense errors will occur because the guest will send
read/write requests that are larger than the underlying host device
is configured to support. An example of this behavior can be seen
in [1].
A workaround is to set the max_sectors_kb host value back in the guest
kernel (a process that can be automated using rc.local startup scripts
and the like), but this has several drawbacks:
- it can be troublesome if the guest has many passthrough devices that
needs this tuning;
- if a change in max_sectors_kb is made in the host side, manual change
in the guests will also be required;
- during an OS install it is difficult, and sometimes not possible, to
go to a terminal and change the max_sectors_kb prior to the installation.
This means that the disk can't be used during the install process. The
easiest alternative here is to roll back to scsi-hd, install the guest
and then go back to SCSI passthrough when the installation is done and
max_sectors_kb can be set.
An easier way would be to QEMU handle the absence of the Block Limits
VPD device response, setting max_io_sectors accordingly and allowing
the guest to use the device without the hassle.
This patch adds emulation of the Block Limits VPD response for
SCSI passthrough devices of type TYPE_DISK that doesn't support
it. The following changes were made:
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply. In case the device does not
- a new function called scsi_generic_set_vpd_bl_emulation,
that is called during device realize, was created to set a
new flag 'needs_vpd_bl_emulation' of the device. This function
retrieves the Inquiry EVPD response of the device to check for
VPD BL support.
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply in case the device needs
VPD BL emulation, adding the Block Limits page (0xb0) to
the list. This will make the guest kernel aware of the
support that we're now providing by emulation.
- a new function scsi_emulate_block_limits creates the
emulated Block Limits response. This function is called
inside scsi_read_complete in case the device requires
Block Limits VPD emulation and we detected a SCSI Sense
error in the VPD Block Limits reply that was issued
from the guest kernel to the device. This error is
expected: we're reporting support from our side, but
the device isn't aware of it.
With this patch, the guest now queries the Block Limits
page during the device configuration because it is being
advertised in the Supported Pages response. It will either
receive the Block Limits page from the hardware, if it supports
it, or will receive an emulated response from QEMU. At any rate,
the guest now has the information to set the max_sectors_kb
parameter accordingly, sparing the user of SCSI sense errors
that would happen without the emulated response and in the
absence of Block Limits support from the hardware.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-4-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the VPD Block Limits emulation with SCSI passthrough,
we'll issue an Inquiry request with EVPD set to retrieve
the available VPD pages of the device. This would be done in
a way similar of what scsi_generic_read_device_identification
does: create a SCSI command and a reply buffer, fill in the
sg_io_hdr_t structure, call blk_ioctl, check if an error
occurred, process the response.
This same process is done in other 2 functions, get_device_type
and get_stream_blocksize. They differ in the command/reply
buffer and post-processing, everything else is almost a
copy/paste.
Instead of adding a forth copy/pasted-ish code when adding
the passthrough VPD BL emulation, this patch extirpates
this repetition of those 3 functions and put it into
a new one called scsi_SG_IO_FROM_DEV. Any future code that
wants to execute an SG_DXFER_FROM_DEV to the device can
use it, avoiding filling sg_io_hdr_t again and et cetera.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-3-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To add support for the emulation of Block Limits VPD page
for passthrough devices, a few adjustments in the current code
base is required to avoid repetition and improve clarity.
In scsi-generic.c, detach the Inquiry handling from
scsi_read_complete and put it into a new function called
scsi_handle_inquiry_reply. This change aims to avoid
cluttering of scsi_read_complete when we more logic in the
Inquiry response handling is added in the next patches,
centralizing the changes in the new function.
In scsi-disk.c, take the build of all emulated VPD pages
from scsi_disk_emulate_inquiry and make it available to
other files into a non-static function called
scsi_disk_emulate_vpd_page. Making it public will allow
the future VPD BL emulation code for passthrough devices
to use it from scsi-generic.c, avoiding copy/pasting this
code solely for that purpose. It also has the advantage of
providing emulation of all VPD pages in case we need to
emulate other pages in other scenarios. As a bonus,
scsi_disk_emulate_inquiry got tidier.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-2-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's start to use "info pic" just like other platforms. For now we
keep the command for a while so that old users can know what is the new
command to use.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-6-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This include both userspace and in-kernel ioapic. Note that the numbers
can be inaccurate for kvm-ioapic. One reason is the same with
kvm-i8259, that when irqfd is used, irqs can be delivered all inside
kernel without our notice. Meanwhile, kvm-ioapic is specially treated
when irq numbers <ISA_NUM_IRQS, those irqs will be delivered in kernel
too via kvm-i8259 (please refer to kvm_pc_gsi_handler).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Let's try to reduce error handling a bit. In the plug/unplug case, the
device was realized and therefore we can assume that getting access to
the memory region will not fail.
For get_vmstate_memory_region() this is already handled that way.
Document both cases.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-13-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This way we can easily check if the region has already been inititalized
without having to rely on the size of an uninitialized region being 0.
Free the region in nvdimm_finalize() and not in unrealize() as we will
allow to create the region before realization in following patches.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-11-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Importantly, get_vmstate_memory_region() should also fail with a proper
error if called before the device is realized. For a PCDIMM, both functions
are to return the same thing, so share the implementation.
All current users are called after the device has been realized, so we
can expect the calls to succeed.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-9-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Not used outside of pc-dimm.c and there shouldn't be other users. If
other devices (e.g. memory devices) ever have to also use slots, then we
will have to factor this out.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-5-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's rename it to make it look more consistent.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-4-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Determining the size of a field is useful when you don't have a struct
variable handy. Open-coding this is ugly.
This patch adds the sizeof_field() macro, which is similar to
typeof_field(). Existing instances are updated to use the macro.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20180614164431.29305-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* aspeed: set APB clocks correctly (fixes slowdown on palmetto)
* smmuv3: cache config data and TLB entries
* v7m/v8m: support read/write from MPU regions smaller than 1K
* various: clean up logging/debug messages
* xilinx_spips: Make dma transactions as per dma_burst_size
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZiOR
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180626' into staging
target-arm queue:
* aspeed: set APB clocks correctly (fixes slowdown on palmetto)
* smmuv3: cache config data and TLB entries
* v7m/v8m: support read/write from MPU regions smaller than 1K
* various: clean up logging/debug messages
* xilinx_spips: Make dma transactions as per dma_burst_size
# gpg: Signature made Tue 26 Jun 2018 17:55:46 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180626: (32 commits)
aspeed/timer: use the APB frequency from the SCU
aspeed: initialize the SCU controller first
aspeed/scu: introduce clock frequencies
hw/arm/smmuv3: Add notifications on invalidation
hw/arm/smmuv3: IOTLB emulation
hw/arm/smmuv3: Cache/invalidate config data
hw/arm/smmuv3: Fix translate error handling
target/arm: Handle small regions in get_phys_addr_pmsav8()
target/arm: Set page (region) size in get_phys_addr_pmsav7()
tcg: Support MMU protection regions smaller than TARGET_PAGE_SIZE
hw/arm/stellaris: Use HWADDR_PRIx to display register address
hw/arm/stellaris: Fix gptm_write() error message
hw/net/smc91c111: Use qemu_log_mask(UNIMP) instead of fprintf
hw/net/smc91c111: Use qemu_log_mask(GUEST_ERROR) instead of hw_error
hw/net/stellaris_enet: Use qemu_log_mask(GUEST_ERROR) instead of hw_error
hw/net/stellaris_enet: Fix a typo
hw/arm/stellaris: Use qemu_log_mask(UNIMP) instead of fprintf
hw/arm/omap: Use qemu_log_mask(GUEST_ERROR) instead of fprintf
hw/arm/omap1: Use qemu_log_mask(GUEST_ERROR) instead of fprintf
hw/i2c/omap_i2c: Use qemu_log_mask(UNIMP) instead of fprintf
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The timer controller can be driven by either an external 1MHz clock or
by the APB clock. Today, the model makes the assumption that the APB
frequency is always set to 24MHz but this is incorrect.
The AST2400 SoC on the palmetto machines uses a 48MHz input clock
source and the APB can be set to 48MHz. The consequence is a general
system slowdown. The QEMU machines using the AST2500 SoC do not seem
impacted today because the APB frequency is still set to 24MHz.
We fix the timer frequency for all SoCs by linking the Timer model to
the SCU model. The APB frequency driving the timers is now the one
configured for the SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All Aspeed SoC clocks are driven by an input source clock which can
have different frequencies : 24MHz or 25MHz, and also, on the Aspeed
AST2400 SoC, 48MHz. The H-PLL (CPU) clock is defined from a
calculation using parameters in the H-PLL Parameter register or from a
predefined set of frequencies if the setting is strapped by hardware
(Aspeed AST2400 SoC). The other clocks of the SoC are then defined
from the H-PLL using dividers.
We introduce first the APB clock because it should be used to drive
the Aspeed timer model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On TLB invalidation commands, let's call registered
IOMMU notifiers. Those can only be UNMAP notifiers.
SMMUv3 does not support notification on MAP (VFIO).
This patch allows vhost use case where IOTLB API is notified
on each guest IOTLB invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We emulate a TLB cache of size SMMU_IOTLB_MAX_SIZE=256.
It is implemented as a hash table whose key is a combination
of the 16b asid and 48b IOVA (Jenkins hash).
Entries are invalidated on TLB invalidation commands, either
globally, or per asid, or per asid/iova.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1529653501-15358-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's cache config data to avoid fetching and parsing STE/CD
structures on each translation. We invalidate them on data structure
invalidation commands.
We put in place a per-smmu mutex to protect the config cache. This
will be useful too to protect the IOTLB cache. The caches can be
accessed without BQL, ie. in IO dataplane. The same kind of mutex was
put in place in the intel viommu.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TCMI_VERBOSE is no more used, drop the OMAP_8/16/32B_REG macros.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Qspi dma has a burst length of 64 bytes, So limit the transactions w.r.t
dma-burst-size property.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1529660880-30376-1-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit a8bff79e9f we added a definition to hw/virtio/virtio-gpu.h
for VIRTIO_GPU_CAPSET_VIRGL2, as a workaround for it not yet being
in the Linux kernel headers. In commit 77d361b13c we updated our
kernel headers to a version which does define the macro, so we can
now remove our workaround.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180622173249.29963-1-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The oldest machine type which is still used in a still maintained distro
is a pc-0.12 based machine type in RHEL6, so everything that is older
than pc-0.12 should not be used anymore. Thus let's deprecate pc-0.10
and pc-0.11 so that we can finally remove them in a future release.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1529917512-10528-1-git-send-email-thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Also add a compat property to disable it for old machine types,
needed for live migration compatibility.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-6-kraxel@redhat.com
Enable TOPOEXT feature on EPYC CPU. This is required to support
hyperthreading on VM guests. Also extend xlevel to 0x8000001E.
Disable topoext on PC_COMPAT_2_12 and keep xlevel 0x8000000a.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <1529443919-67509-3-git-send-email-babu.moger@amd.com>
[ehabkost: Added EPYC-IBPB.xlevel to PC_COMPAT_2_12]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1T5q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180622' into staging
target-arm queue:
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
# gpg: Signature made Fri 22 Jun 2018 13:56:00 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180622: (28 commits)
xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
vl.c: Don't zero-initialize statics for serial_hds
target/arm: Strict alignment for ARMv6-M and ARMv8-M Baseline
target/arm: Introduce ARM_FEATURE_M_MAIN
hw/arm/mps2-tz.c: Instantiate MPCs
hw/arm/iotkit: Wire up MPC interrupt lines
hw/arm/iotkit: Instantiate MPC
hw/misc/iotkit-secctl.c: Implement SECMPCINTSTATUS
hw/misc/tz_mpc.c: Honour the BLK_LUT settings in translate
hw/misc/tz-mpc.c: Implement correct blocked-access behaviour
hw/misc/tz-mpc.c: Implement registers
hw/misc/tz-mpc.c: Implement the Arm TrustZone Memory Protection Controller
xlnx-zynqmp: Swap Cortex-R5 for Cortex-R5F
target-arm: Add the Cortex-R5F
hw/arm/virt: Increase max_cpus to 512
hw/arm/virt: Use 256MB ECAM region by default
hw/arm/virt: Add virt-3.0 machine type
hw/arm/virt: Add a new 256MB ECAM region
hw/arm/virt: Register two redistributor regions when necessary
hw/arm/virt-acpi-build: Advertise one or two GICR structures
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The interrupt outputs from the MPC in the IoTKit and the expansion
MPCs in the board must be wired up to the security controller, and
also all ORed together to produce a single line to the NVIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-8-peter.maydell@linaro.org
Wire up the one MPC that is part of the IoTKit itself. For the
moment we don't wire up its interrupt line.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-7-peter.maydell@linaro.org
Implement the SECMPCINTSTATUS register. This is the only register
in the security controller that deals with Memory Protection
Controllers, and it simply provides a read-only view of the
interrupt lines from the various MPCs in the system.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180620132032.28865-6-peter.maydell@linaro.org
Implement the missing registers for the TZ MPC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-3-peter.maydell@linaro.org
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
With this patch, virt-3.0 machine uses a new 256MB ECAM region
by default instead of the legacy 16MB one, if highmem is set
(LPAE supported by the guest) and (!firmware_loaded || aarch64).
Indeed aarch32 mode FW may not support this high ECAM region.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-11-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch defines a new ECAM region located after the 256GB limit.
The virt machine state is augmented with a new highmem_ecam field
which guards the usage of this new ECAM region instead of the legacy
16MB one. With the highmem ECAM region, up to 256 PCIe buses can be
used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows the creation of a GICv3 node with 1 or 2
redistributor regions depending on the number of smu_cpus.
The second redistributor region is located just after the
existing RAM region, at 256GB and contains up to up to 512 vcpus.
Please refer to kernel documentation for further node details:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-6-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To prepare for multiple redistributor regions, we introduce
an array of uint32_t properties that stores the redistributor
count of each redistributor region.
Non accelerated VGICv3 only supports a single redistributor region.
The capacity of all redist regions is checked against the number of
vcpus.
Machvirt is updated to set those properties, ie. a single
redistributor region with count set to the number of vcpus
capped by 123.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-4-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The way we used to handle KVM allowable guest pagesizes for PAPR guests
required some convoluted checking of memory attached to the guest.
The allowable pagesizes advertised to the guest cpus depended on the memory
which was attached at boot, but then we needed to ensure that any memory
later hotplugged didn't change which pagesizes were allowed.
Now that we have an explicit machine option to control the allowable
maximum pagesize we can simplify this. We just check all memory backends
against that declared pagesize. We check base and cold-plugged memory at
reset time, and hotplugged memory at pre_plug() time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The way the POWER Hash Page Table (HPT) MMU is virtualized by KVM HV means
that every page that the guest puts in the pagetables must be truly
physically contiguous, not just GPA-contiguous. In effect this means that
an HPT guest can't use any pagesizes greater than the host page size used
to back its memory.
At present we handle this by changing what we advertise to the guest based
on the backing pagesizes. This is pretty bad, because it means the guest
sees a different environment depending on what should be host configuration
details.
As a start on fixing this, we add a new capability parameter to the
pseries machine type which gives the maximum allowed pagesizes for an
HPT guest. For now we just create and validate the parameter without
making it do anything.
For backwards compatibility, on older machine types we set it to the max
available page size for the host. For the 3.0 machine type, we fix it to
16, the intention being to only allow HPT pagesizes up to 64kiB by default
in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't emulate slave mode so related registers are not needed.
[lh]sadr are only retained to avoid too many warnings and simplify
debugging but sdata is not even correct because device has a 4 byte
FIFO instead so just remove this unimplemented register for now.
The intr register is also not implemented correctly, it is for
diagnostics and normally not even visible on device without explicitly
enabling it. As no guests are known to need this remove it as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_irq_alloc_block and spapr_irq_alloc() are now deprecated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, when a device requests for IRQ number in a sPAPR machine, the
spapr_irq_alloc() routine first scans the ICSState status array to
find an empty slot and then performs the assignement of the selected
numbers. Split this sequence in two distinct routines : spapr_irq_find()
for lookups and spapr_irq_claim() for claiming the IRQ numbers.
This will ease the introduction of a static layout of IRQ numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr capabilities have an apply hook to actually activate (or deactivate)
the feature in the system at reset time. However, a number of capabilities
affect the setup of cpus, and need to be applied to each of them -
including hotplugged cpus for extra complication. To make this simpler,
add an optional cpu_apply hook that is called from spapr_cpu_reset().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Previously, the effective values of the various spapr capability flags
were only determined at machine reset time. That was a lazy way of making
sure it was after cpu initialization so it could use the cpu object to
inform the defaults.
But we've now improved the compat checking code so that we don't need to
instantiate the cpus to use it. That lets us move the resolution of the
capability defaults much earlier.
This is going to be necessary for some future capabilities.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It introduces a base PnvChip class from which the specific processor
chip classes, Pnv8Chip and Pnv9Chip, inherit. Each of them needs to
define an init and a realize routine which will create the controllers
of the target processor. For the moment, the base PnvChip class
handles the XSCOM bus and the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A per-CPU machine data pointer was recently added to PowerPCCPU. The
motivation is to to hide platform specific details from the core CPU
code. This per-CPU data can hold state which is relevant to the guest
though, eg, Virtual Processor Areas, and we should migrate this state.
This patch adds the plumbing so that we can migrate the per-CPU data
for PAPR guests. We only do this for newer machine types for the sake
of backward compatibility. No state is migrated for the moment: the
vmstate_spapr_cpu_state structure will be populated by subsequent
patches.
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fix some trivial spelling and spacing errors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On Power9, the thread interrupt presenter has a different type and is
linked to the chip owning the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The boot framebuffer is expected to be configured by the firmware, so it
uses fw_cfg as interface. Initialization goes as follows:
(1) Check whenever etc/ramfb is present.
(2) Allocate framebuffer from RAM.
(3) Fill struct RAMFBCfg, write it to etc/ramfb.
Done. You can write stuff to the framebuffer now, and it should appear
automagically on the screen.
Note that this isn't very efficient because it does a full display
update on each refresh. No dirty tracking. Dirty tracking would have
to be active for the whole ram slot, so that wouldn't be very efficient
either. For a boot display which is active for a short time only this
isn't a big deal. As permanent guest display something better should be
used (if possible).
This is the ramfb core code. Some windup is needed for display devices
which want have a ramfb boot display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20180613122948.18149-2-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
CPUPPCState currently contains a number of fields containing the state of
the VPA. The VPA is a PAPR specific concept covering several guest/host
shared memory areas used to communicate some information with the
hypervisor.
As a PAPR concept this is really machine specific information, although it
is per-cpu, so it doesn't really belong in the core CPU state structure.
There's also other information that's per-cpu, but platform/machine
specific. So create a (void *)machine_data in PowerPCCPU which can be
used by the machine to locate per-cpu data. Intialization, lifetime and
cleanup of machine_data is entirely up to the machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Currently, we allocate space for all the cpu objects within a single core
in one big block. This was copied from an older version of the spapr code
and requires some ugly pointer manipulation to extract the individual
objects.
This design was due to a misunderstanding of qemu lifetime conventions and
has already been changed in spapr (in 94ad93bd "spapr_cpu_core: instantiate
CPUs separately".
Make an equivalent change in pnv_core to get rid of the nasty pointer
arithmetic.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
In the case where we have an interrupt generated externally from inputs to
bits 1 and 2 of port A and/or port B, it is necessary to expose
mos6522_update_irq() so it can be called by the interrupt source.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PMU device supercedes the CUDA device found on older New World Macs and
is supported by a larger number of guest OSs from OS 9 to OS X 10.5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MacOS 9 has a bug in its PMU driver whereby after configuring the ADB bus
devices it sends another write to reg 3 on both devices resetting them
both back to the same address.
Add a new disable_direct_reg3_writes property to ADBDevice to disable these
direct writes which can enabled just for the upcoming pmu-adb support.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PMU-enabled New World Macs expose their GPIOs via a separate memory region
within the macio device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This option allows the VIA configuration to be controlled between 3
different possible setups: cuda, pmu-adb and pmu with USB rather than ADB
keyboard/mouse.
For the moment we don't do anything with the configuration except to pass
it to the macio device (the via-cuda parent) and also to the firmware via
the fw_cfg interface so that it can present the correct device tree.
The default is cuda which is the current default and so will have no
change in behaviour.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
-----BEGIN PGP SIGNATURE-----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=LxgF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
# gpg: Signature made Fri 15 Jun 2018 15:20:03 BST
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (26 commits)
block: Remove dead deprecation warning code
block: Remove deprecated -drive option serial
block: Remove deprecated -drive option addr
block: Remove deprecated -drive geometry options
rbd: New parameter key-secret
rbd: New parameter auth-client-required
block: Fix -blockdev / blockdev-add for empty objects and arrays
check-block-qdict: Cover flattening of empty lists and dictionaries
check-block-qdict: Rename qdict_flatten()'s variables for clarity
block-qdict: Simplify qdict_is_list() some
block-qdict: Clean up qdict_crumple() a bit
block-qdict: Tweak qdict_flatten_qdict(), qdict_flatten_qlist()
block-qdict: Simplify qdict_flatten_qdict()
block: Make remaining uses of qobject input visitor more robust
block: Factor out qobject_input_visitor_new_flat_confused()
block: Clean up a misuse of qobject_to() in .bdrv_co_create_opts()
block: Fix -drive for certain non-string scalars
block: Fix -blockdev for certain non-string scalars
qobject: Move block-specific qdict code to block-qdict.c
block: Add block-specific QDict header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the IoTKit MPC support, we need to wire together the
interrupt outputs of 17 MPCs; this exceeds the current
value of MAX_OR_LINES. Increase MAX_OR_LINES to 32 (which
should be enough for anyone).
The tricky part is retaining the migration compatibility for
existing OR gates; we add a subsection which is only used
for larger OR gates, and define it such that we can freely
increase MAX_OR_LINES in future (or even move to a dynamically
allocated levels[] array without an upper size limit) without
breaking compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-10-peter.maydell@linaro.org
Remove the now-unused armv7m_init() function. This was a legacy from
before we properly QOMified ARMv7M, and it has some flaws:
* it combines work that needs to be done by an SoC object (creating
and initializing the TYPE_ARMV7M object) with work that needs to
be done by the board model (setting the system up to load the ELF
file specified with -kernel)
* TYPE_ARMV7M creation failure is fatal, but an SoC object wants to
arrange to propagate the failure outward
* it uses allocate-and-create via qdev_create() whereas the current
preferred style for SoC objects is to do creation in-place
Board and SoC models can instead do the two jobs this function
was doing themselves, in the right places and with whatever their
preferred style/error handling is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601144328.23817-3-peter.maydell@linaro.org
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
-----BEGIN PGP SIGNATURE-----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=g3bP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.0-20180612' into staging
ppc patch queue 2018-06-12
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
# gpg: Signature made Tue 12 Jun 2018 07:43:21 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.0-20180612: (33 commits)
spapr_pci: Remove unhelpful pagesize warning
xics_kvm: use KVM helpers
ppc/pnv: fix LPC HC firmware address space
spapr: handle cpu core unplug via hotplug handler chain
spapr: handle pc-dimm unplug via hotplug handler chain
spapr: introduce machine unplug handler
spapr: move memory hotplug support check into spapr_memory_pre_plug()
spapr: move lookup of the node into spapr_memory_plug()
spapr: no need to verify the node
target/ppc: Allow PIR read in privileged mode
ppc4xx_i2c: Clean up and improve error logging
target/ppc: extend eieio for POWER9
mos6522: convert VMSTATE_TIMER_PTR_TEST to VMSTATE_TIMER_PTR
mos6522: move timer frequency initialisation to mos6522_reset
cuda: embed mos6522_cuda device directly rather than using QOM object link
mos6522: fix vmstate_mos6522_timer version in vmstate_mos6522
ppc: add missing FW_CFG_PPC_NVRAM_FLAT definition
ppc: remove obsolete macio_init() definition from mac.h
ppc: remove obsolete pci_pmac_init() definitions from mac.h
hw/misc/mos6522: Add trailing '\n' to qemu_log() calls
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A specific MemoryRegion is required for the LPC HC Firmware address
space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 6522 VIA timer frequency cannot be set by altering registers within the
device itself and hence it is a fixed property of the machine.
Move the initialisation of the timer frequency to the mos6522 reset function
and ensure that any subclasses always call the parent reset function so that
it isn't required to store the timer frequency within vmstate_mos6522_timer
itself.
By moving the frequency initialisation to the device reset function then we
find that the realize function for both mos6522 and mos6522_cuda becomes
obsolete and can simply be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Examining the migration stream it can be seen that the mos6522 device state is
being stored separately rather than as part of the CUDA device which is
incorrect (and likely to cause issues if another mos6522 device is added to
the machine).
Resolve this by embedding the mos6522_cuda device directly within the CUDA
device rather than using a QOM object link to reference the device separately.
Note that we also bump the version in vmstate_cuda to reflect this change: this
isn't particularly important for the moment as the Mac machine migration isn't
100% reliable due to issues migrating the timebase under TCG.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is used in OpenBIOS to define the memory layout of the NVRAM device. Whilst
currently left at its default value, add the missing definition to ensure it is
reserved.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
>From observation of various OS sources it can be seen that the token register
introduced in 4e46dcdbd3 "PPC: Newworld: Add uninorth token register" is not
required, since the only register currently implemented is the uninorth hardware
version which is read-only.
Remove the token register implementation and instead return the uninorth
version corresponding to the hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace the "nvdimm-cap" option which took numeric arguments such as "2"
with a more user friendly "nvdimm-persistence" option which takes symbolic
arguments "cpu" or "mem-ctrl".
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For the case where the end_transfer_func is also the caller of
ide_transfer_start, the mutual recursion can lead to unlimited
stack usage. Introduce a new version that can be used to change
tail recursion into a loop, and use it in trace_ide_atapi_cmd_reply_end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-8-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Now that end_transfer_func is a tail call in ahci_start_transfer,
formalize the fact that the callback (of which ahci_start_transfer is
the sole implementation) takes care of the transfer too: rename it to
pio_transfer and, if it is present, call the end_transfer_func as soon
as it returns.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of this commit, the Spec v1 is not working, and all controllers
expect the cards to be conformant to Spec v2.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximum frame size includes the CRC and depends if a VLAN tag is
inserted or not. Adjust the frame size limit in the transmit handler
using on the FTGMAC100State buffer size and in the receive handler use
the packet protocol.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530061711.23673-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Specs are available here :
https://www.nxp.com/docs/en/application-note/AN264.pdf
This is a simple model supporting the basic registers for led and GPIO
mode. The device also supports two blinking rates but not the model
yet.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is an helper routine to add a single EEPROM on an I2C bus. It can
be directly used by smbus_eeprom_init() which adds a certain number of
EEPROMs on mips and x86 machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While we skip the GIC_INTERNAL irqs, we don't change the register offset
accordingly. This will overlap the GICR registers value and leave the
last GIC_INTERNAL irq's registers out of update.
Fix this by skipping the registers banked by GICR.
Also for migration compatibility if the migration source (old version
qemu) doesn't send gicd_no_migration_shift_bug = 1 to destination, then
we shift the data of PPI to get the right data for SPI.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1527816987-16108-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This macro isn't used by any VFIO code. And its name is
too generic. The vfio-common.h (in include/hw/vfio) can
be included by other modules in QEMU. It can introduce
conflicts.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU 3.0 enables strict check for compression & decompression to
make the migration more robust, that depends on the source to fix
the internal design which triggers the unexpected error conditions
To make it work for migrating old version QEMU to 2.13 QEMU, we
introduce this parameter to disable the error check on the
destination which is the default behavior of the machine type
which is older than 2.13, alternately, the strict check can be
enabled explicitly as followings:
-M pc-q35-2.11 -global migration.decompress-error-check=true
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Read only feature shouldn't be negotiable, because if the
backend device reported Read only feature supported, QEMU
host driver shouldn't change backend's RO attribute. While
here, also enable the vhost-user-blk test utility to test
RO feature.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a machine command line option to allow the user to control the Platform
Capabilities Structure in the virtualized NFIT. This Platform Capabilities
Structure was added in ACPI 6.2 Errata A.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since no devices use it, we can safely remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-5-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Removal of DeviceClass::init() moved from previous patch, missing
documentation updates supplied]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-5-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SMBusDeviceClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-2-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-2-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 5643cc94ac ("virtio-gpu-3d: add support for second capability
set (v4)") updated virtio_gpu.h with a define that does not yet(?)
exist upstream resulting in build breakage every time Linux headers
are updated via the standard update script. Conditionally define this
within QEMU code instead to avoid future breakage.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Fixes: 5643cc94ac ("virtio-gpu-3d: add support for second capability set (v4)")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180525132755.21839-2-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-22-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-17-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Xen 4.11 has a new API to directly map guest resources. Among the resources
that can be mapped using this API are ioreq pages.
This patch modifies QEMU to attempt to use the new API should it exist,
falling back to the previous mechanism if it is unavailable.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
No declaration of "hw/vfio/vfio-common.h" directly requires to include
the "exec/address-spaces.h" header. To simplify dependencies and
ease the upcoming cleanup of "exec/address-spaces.h", directly include
it in the source file where the declaration are used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-2-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces VHOST_USER_PROTOCOL_F_HOST_NOTIFIER.
With this feature negotiated, vhost-user backend can register
memory region based host notifiers. And it will allow the guest
driver in the VM to notify the hardware accelerator at the
vhost-user backend directly.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When multi queue is enabled e.g. for a virtio-net device,
each queue pair will have a vhost_dev, and the only thing
shared between vhost devs currently is the chardev. This
patch introduces a vhost-user state structure which will
be shared by all vhost devs of the same virtio device.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces a vhost op for vhost backends to allow
them to filter the memory sections that they can handle.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbBX2cAAoJECgfDbjSjVRpOEYIAIR6KGkwbAJ9SnO9B71DQHl1
yYYgM7i2HwyZ1YPnXOYWnI1lzQ1bARTf2krQJFGmfjlDaueFf9KnXdNByoVCmG8m
UhF/rQp3DcJ4wTABktPtME8gWdQxKPmDxlN5W3f29Zrm3g9S+Hshi+sfPZUkBxL4
gQMFRctb2SxvQXG+lusHVwo1oF6pzGZMmX35906he3m4xS/cfoeCP7Qj6nSvHZq7
lsLoOeYxHtXWA9gTYxpd7zW+hhUxkspoOqcXySHfO7e5enJANaulTxKuC0T+6HL4
O2iUM+1wjUYE0tQcNJ6x7emA82k5OdG2OMD6gbR1oSdquttJo7+4R+goqpb44rc=
=NUoY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio, vhost: fixes, features
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 23 May 2018 15:41:32 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (28 commits)
intel-iommu: rework the page walk logic
util: implement simple iova tree
intel-iommu: trace domain id during page walk
intel-iommu: pass in address space when page walk
intel-iommu: introduce vtd_page_walk_info
intel-iommu: only do page walk for MAP notifiers
intel-iommu: add iommu lock
intel-iommu: remove IntelIOMMUNotifierNode
intel-iommu: send PSI always even if across PDEs
nvdimm: fix typo in label-size definition
contrib/vhost-user-blk: enable protocol feature for vhost-user-blk
hw/virtio: Fix brace Werror with clang 6.0.0
libvhost-user: Send messages with no data
vhost-user+postcopy: Use qemu_set_nonblock
virtio: support setting memory region based host notifier
vhost-user: support receiving file descriptors in slave_read
vhost-user: add Net prefix to internal state structure
linux-headers: add kvm header for mips
linux-headers: add unistd.h on all arches
update-linux-headers.sh: unistd.h, kvm consistency
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJbBGT2AAoJEIlPj0hw4a6Q0BIQAIciEH80ZLPSQPJciRoBCB/s
1BUsbFelfeHcTXAOxiahmaQbzzffosifK0uJAH5Quy5RotnKknguRgfgAl8nWX34
vXBbYKOmdudNwk3wIhcnnLfiRvNcdF4yDVVArsnvEbCWUBV2mpTrhuqmepZMiY7s
GQU42ly09WQePBPFW19RS/kxsaR1lSuGIuSxtc+0QvDQpqMRK3HslHrjD0jgUISh
pitqL3ztPHpJN1d9KI9fNT066magjnAkWV1gSYH9MAFvWV6JVuXqyJPY/x+YcZEU
uPgZdEmONIoFqLD7yEHf/kXtCoRZavnvX3t0OPvUOPrN8eeui/UrtOyElY0NxmS/
RGKggOAjN4VYdAfXHqLIWHkkE8CicFkukr6hk2nyfDKT63ZTR6TfEESrweL3clej
J2dQ1bPvmAhlPU7tFeo8drAFgeIjLl9QAXEtp2+1FXGYBOT4avwtnt4rrGpnSbpL
wV6SObd4d8yJR1JrA42jXuL2qlubainlceg4dSFGf84iUx68Sq+DXM+ssbVxs4Tc
VEJ2nIGK2OF0jafFUV4sqZ7iDQoor0A/SGiOHk8j3kr/kWbidid6opl+MRcr/II3
CYHyR8IH3LLY/CY18ppVbuCNxovPTilwRsleNy6ZxM1uFeWIOGWUy0WutPTi8wq8
Ksa1MVPftDaMOLL2WE5C
=e+YI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/sstabellini-http/tags/xen-20180522-tag' into staging
Xen 2018/05/22
# gpg: Signature made Tue 22 May 2018 19:44:06 BST
# gpg: using RSA key 894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
# gpg: aka "Stefano Stabellini <sstabellini@kernel.org>"
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* remotes/sstabellini-http/tags/xen-20180522-tag:
xen_disk: be consistent with use of xendev and blkdev->xendev
xen_disk: use a single entry iovec
xen_backend: make the xen_feature_grant_copy flag private
xen_disk: remove use of grant map/unmap
xen_backend: add an emulation of grant copy
xen: remove other open-coded use of libxengnttab
xen_disk: remove open-coded use of libxengnttab
xen_backend: add grant table helpers
xen: add a meaningful declaration of grant_copy_segment into xen_common.h
checkpatch: generalize xen handle matching in the list of types
xen-hvm: create separate function for ioreq server initialization
xen_pt: Present the size of 64 bit BARs correctly
configure: Add explanation for --enable-xen-pci-passthrough
xen/pt: use address_space_memory object for memory region hooks
xen-pvdevice: Introduce a simplistic xen-pvdevice save state
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a new header file, move the bochs vbe dispi interface
defines to it, so they can be used outside vga code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180522165058.15404-2-kraxel@redhat.com
This patch fixes a potential small window that the DMA page table might
be incomplete or invalid when the guest sends domain/context
invalidations to a device. This can cause random DMA errors for
assigned devices.
This is a major change to the VT-d shadow page walking logic. It
includes but is not limited to:
- For each VTDAddressSpace, now we maintain what IOVA ranges we have
mapped and what we have not. With that information, now we only send
MAP or UNMAP when necessary. Say, we don't send MAP notifies if we
know we have already mapped the range, meanwhile we don't send UNMAP
notifies if we know we never mapped the range at all.
- Introduce vtd_sync_shadow_page_table[_range] APIs so that we can call
in any places to resync the shadow page table for a device.
- When we receive domain/context invalidation, we should not really run
the replay logic, instead we use the new sync shadow page table API to
resync the whole shadow page table without unmapping the whole
region. After this change, we'll only do the page walk once for each
domain invalidations (before this, it can be multiple, depending on
number of notifiers per address space).
While at it, the page walking logic is also refactored to be simpler.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Tested-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For UNMAP-only IOMMU notifiers, we don't need to walk the page tables.
Fasten that procedure by skipping the page table walk. That should
boost performance for UNMAP-only notifiers like vhost.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SECURITY IMPLICATION: this patch fixes a potential race when multiple
threads access the IOMMU IOTLB cache.
Add a per-iommu big lock to protect IOMMU status. Currently the only
thing to be protected is the IOTLB/context cache, since that can be
accessed even without BQL, e.g., in IO dataplane.
Note that we don't need to protect device page tables since that's fully
controlled by the guest kernel. However there is still possibility that
malicious drivers will program the device to not obey the rule. In that
case QEMU can't really do anything useful, instead the guest itself will
be responsible for all uncertainties.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
That is not really necessary. Removing that node struct and put the
list entry directly into VTDAddressSpace. It simplfies the code a lot.
Since at it, rename the old notifiers_list into vtd_as_with_notifiers.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Fixes: commit da6789c27c ("nvdimm: add a macro for property "label-size"")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces the support for setting memory region
based host notifiers for virtio device. This is helpful when
using a hardware accelerator for a virtio device, because
hardware heavily depends on the notification, this will allow
the guest driver in the VM to notify the hardware directly.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no longer any use of this flag outside of the xen_backend code.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
This patch adds grant table helper functions to the xen_backend code to
localize error reporting and use of xen_domid.
The patch also defers the call to xengnttab_open() until just before the
initialise method in XenDevOps is invoked. This method is responsible for
mapping the shared ring. No prior method requires access to the grant table.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Currently the xen_disk source has to carry #ifdef exclusions to compile
against Xen older then 4.8. This is a bit messy so this patch lifts the
definition of struct xengnttab_grant_copy_segment and adds it into the
pre-4.8 compat area in xen_common.h, which allows xen_disk to be cleaned
up.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
There is no need to include pci.h in these files.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The ZynqMP contains two instances of a generic DMA, the GDMA, located in the
FPD (full power domain), and the ADMA, located in LPD (low power domain). This
patch adds these two DMAs to the ZynqMP board.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180503214201.29082-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the generic DMA found on Xilinx ZynqMP.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180503214201.29082-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The property legacy-cache will be used to control the cache information.
If user passes "-cpu legacy-cache" then older information will
be displayed even if the hardware supports new information. Otherwise
use the statically loaded cache definitions if available.
Renamed the previous cache structures to legacy_*. If there is any change in
the cache information, then it needs to be initialized in builtin_x86_defs.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180514164156.27034-3-babu.moger@amd.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This fixes an issue by adding bounds checking to multi-byte packets
where the PS/2 mouse data stream may become corrupted due to data being
discarded when the PS/2 ringbuffer is full.
Interrupts for Multi-byte responses are postponed until the final byte
has been queued.
These changes fix a bug where windows guests drop the mouse device
entirely requring the guest to be restarted.
Signed-off-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180507150310.2FEA0381924@moya.office.hostfission.com>
[ kraxel: codestyle fixes ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Calling pause_all_vcpus()/resume_all_vcpus() from a VCPU thread might
not be the best idea. As pause_all_vcpus() temporarily drops the qemu
mutex, two parallel calls to pause_all_vcpus() can be active at a time,
resulting in a deadlock. (either by two VCPUs or by the main thread and a
VCPU)
Let's handle it via the main loop instead, as suggested by Paolo. If we
would have two parallel reset requests by two different VCPUs at the
same time, the last one would win.
We use the existing ipl device to handle it. The nice side effect is
that we can get rid of reipl_requested.
This change implies that all reset handling now goes via the common
path, so "no-reboot" handling is now active for all kinds of reboots.
Let's execute any CPU initialization code on the target CPU using
run_on_cpu.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180424101859.10239-1-david@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJa+UAZAAoJEO8Ells5jWIRTJIIAIcpNROupxHEfcAQKU7lIqys
qx/FxKp+lknzzQMwUfmZwT3PuBD+tWuE7ugXgzjVulvE11F+Z3QBPTDBtOObaMa1
qpgIF3zzrNxtuWMc/72Q8/wEE1wtBUo+WTAGw9Xp1dVomYOOsg1wa7dsKdZhRfz7
nIwDW2ftw3/mx+uTW2/a163v+IDDL9L+HOLibQHWUxOMM39ASchiqAXLF4mfhpwH
xr0OPd7wtcmrDsD/CLbdkGCJ/+vsXnY8pzNmy1RjJuDpWpqlgYpJJPtLBfXBo9VA
91sz5+KryzjpXXzKcQuhiU020O1dIKIe3PWqK6z0x0UjtZ1Yox5adZ3eFomHHwU=
=bIws
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 14 May 2018 08:51:53 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: Get rid of 'vlan' terminology and use 'hub' instead in the doc files
net: Get rid of 'vlan' terminology and use 'hub' instead in the source files
net: Remove the deprecated "vlan" parameter
net: Fix memory leak in net_param_nic()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's been marked as deprecated since QEMU v2.9.0, so that should have
been enough time for everybody to either just drop unnecessary "vlan=0"
parameters, to switch to the modern -device + -netdev syntax for connecting
guest NICs with host network backends, or to switch to the "hubport" netdev
in case hubs are really wanted instead.
Buglink: https://bugs.launchpad.net/qemu/+bug/658904
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
load_dtb() depends on arm_load_kernel() to figure out place
in RAM where it should be loaded, but it's not required for
arm_load_kernel() to work. Sometimes it's neccesary for
devices added with -device/device_add to be enumerated in
DTB as well, which's lead to [1] and surrounding commits to
add 2 more machine_done notifiers with non obvious ordering
to make dynamic sysbus devices initialization happen in
the right order.
However instead of moving whole arm_load_kernel() in to
machine_done, it's sufficient to move only load_dtb() into
virt_machine_done() notifier and remove ArmLoadKernelNotifier/
/PlatformBusFDTNotifierParams notifiers, which saves us ~90LOC
and simplifies code flow quite a bit.
Later would allow to consolidate DTB generation within one
function for 'mach-virt' board and make it reentrant so it
could generate updated DTB in device hotplug secenarios.
While at it rename load_dtb() to arm_load_dtb() since it's
public now.
Add additional field skip_dtb_autoload to struct arm_boot_info
to allow manual DTB load later in mach-virt and to avoid touching
all other boards to explicitly call arm_load_dtb().
1) (ac9d32e hw/arm/boot: arm_load_kernel implemented as a machine init done notifier)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1525691524-32265-4-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
platform-bus were using machine_done notifier to get and map
(assign irq/mmio resources) dynamically added sysbus devices
after all '-device' options had been processed.
That however creates non obvious dependencies on ordering of
machine_done notifiers and requires carefull line juggling
to keep it working. For example see comment above
create_platform_bus() and 'straitforward' arm_load_kernel()
had to converted to machine_done notifier and that lead to
yet another machine_done notifier to keep it working
arm_register_platform_bus_fdt_creator().
Instead of hiding resource assignment in platform-bus-device
to magically initialize sysbus devices, use device plug
callback and assign resources explicitly at board level
at the moment each -device option is being processed.
That adds a bunch of machine declaration boiler plate to
e500plat board, similar to ARM/x86 but gets rid of hidden
machine_done notifier and would allow to remove the dependent
notifiers in ARM code simplifying it and making code flow
easier to follow.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1525691524-32265-3-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By default MachineClass::get_hotplug_handler is NULL and concrete board
should set it to it's own handler.
Considering there isn't any default handler, drop saving empty
MachineClass::get_hotplug_handler in child class and make PC code
consistent with spapr/s390x boards.
We can bring this back when actual usecase surfaces and do it
consistently across boards that use get_hotplug_handler().
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 1525691524-32265-2-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
-----BEGIN PGP SIGNATURE-----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=Hhge
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine queue, 2018-05-07
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
# gpg: Signature made Mon 07 May 2018 18:01:42 BST
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
scripts/device-crash-test: Removed fixed CAN entries
vl: allow 'maxmem' without 'slot'
spapr: rename "hotplug memory" terminology to "device memory"
pc: rename "hotplug memory" terminology to "device memory"
machine: rename MemoryHotplugState to DeviceMemoryState
pc-dimm: move actual plug/unplug of a memory region to MemoryDevice
pc-dimm: factor out capacity and slot checks into MemoryDevice
pc-dimm: factor out address search into MemoryDevice code
pc-dimm: pass in the machine and to the MemoryHotplugState
pc-dimm: no need to pass the memory region
machine: make MemoryHotplugState accessible via the machine
pc-dimm: factor out MemoryDevice interface
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWu496QAKCRBr8dezV+8+
T1ZEAJ4wQRHZtn4suN5yMEHQMA2FkX1iNACgiYWLtcNcgoa88eaTcJJJu4QZryY=
=I2wf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-2.13-pull-20180506' into staging
RISC-V: QEMU 2.13 Privileged ISA emulation updates
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
# gpg: Signature made Sun 06 May 2018 00:27:37 BST
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-2.13-pull-20180506:
RISC-V: Mark ROM read-only after copying in code
RISC-V: No traps on writes to misa,minstret,mcycle
RISC-V: Make mtvec/stvec ignore vectored traps
RISC-V: Add mcycle/minstret support for -icount auto
RISC-V: Use [ms]counteren CSRs when priv ISA >= v1.10
RISC-V: Allow S-mode mxr access when priv ISA >= v1.10
RISC-V: Clear mtval/stval on exceptions without info
RISC-V: Hardwire satp to 0 for no-mmu case
RISC-V: Update E and I extension order
RISC-V: Remove erroneous comment from translate.c
RISC-V: Remove EM_RISCV ELF_MACHINE indirection
RISC-V: Make virt header comment title consistent
RISC-V: Make some header guards more specific
RISC-V: Fix missing break statement in disassembler
RISC-V: Include instruction hex in disassembly
RISC-V: Remove unused class definitions
RISC-V: Remove identity_translate from load_elf
RISC-V: Use ROM base address and size from memmap
RISC-V: Make virt board description match spike
RISC-V: Replace hardcoded constants with enum values
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make it clear at relevant places that we are dealing with device
memory. That it can be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-11-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's make it clear that we are dealing with device memory. That it can
be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-10-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to better match the new terminology.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-9-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Registering the memory region for migration has do be done by the owner.
There could be cases, where we don't want to migrate the memory.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-8-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the checks into memory_device_get_free_addr(). This will check
before doing any calculations if we have KVM/vhost slots left and if
the total region size would be exceeded.
Of course, while at it, make it independent of pc-dimm code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This mainly moves code, but does a handfull of optimizations:
- We pass the machine instead of the address space properties
- We check the hinted address directly and handle fragmented memory
better
- We make the search independent of pc-dimm
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-6-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We use the machine internally either way, so let's just pass it in then.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-5-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We can just query it ourselves. When unplugging, we should always be
able to the region (as it was previously plugged). E.g. PPC already
assumed that and used &error_abort.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's allow to query the MemoryHotplugState directly from the machine.
If the pointer is NULL, the machine does not support memory devices. If
the pointer is !NULL, the machine supports memory devices and the
data structure contains information about the applicable physical
guest address space region.
This allows us to generically detect if a certain machine has support
for memory devices, and to generically manage it (find free address
range, plug/unplug a memory region).
We will rename "MemoryHotplugState" to something more meaningful
("DeviceMemory") after we completed factoring out the pc-dimm code into
MemoryDevice code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
[ehabkost: squashed fix to use g_malloc0()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
On the qmp level, we already have the concept of memory devices:
"query-memory-devices"
Right now, we only support NVDIMM and PCDIMM.
We want to map other devices later into the address space of the guest.
Such device could e.g. be virtio devices. These devices will have a
guest memory range assigned but won't be exposed via e.g. ACPI. We want
to make them look like memory device, but not glued to pc-dimm.
Especially, it will not always be possible to have TYPE_PC_DIMM as a parent
class (e.g. virtio devices). Let's use an interface instead. As a first
part, convert handling of
- qmp_pc_dimm_device_list
- get_plugged_memory_size
to our new model. plug/unplug stuff etc. will follow later.
A memory device will have to provide the following functions:
- get_addr(): Necessary, as the property "addr" can e.g. not be used for
virtio devices (already defined).
- get_plugged_size(): The amount this device offers to the guest as of
now.
- get_region_size(): Because this can later on be bigger than the
plugged size.
- fill_device_info(): Fill MemoryDeviceInfo, e.g. for qmp.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Removes a whole lot of unnecessary boilerplate code. Machines
don't need to be objects. The expansion of the SOC object model
for the RISC-V machines will happen in the future as SiFive
plans to add their FE310 and FU540 SOCs to QEMU. However, it
seems that this present boilerplate is complete unnecessary.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Another case of replacing hard coded constants, this time
referring to the definition in the virt machine's memmap.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V device-tree code has a number of hard-coded
constants and this change moves them into header enums.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
This patch builds the smmuv3 node in the ACPI IORT table.
The RID space of the root complex, which spans 0x0-0x10000
maps to streamid space 0x0-0x10000 in smmuv3, which in turn
maps to deviceid space 0x0-0x10000 in the ITS group.
The guest must feature the IOMMU probe deferral series
(https://lkml.org/lkml/2017/4/10/214) which fixes streamid
multiple lookup. This bug is not related to the SMMU emulation.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1524665762-31355-14-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add code to instantiate an smmuv3 in virt machine. A new iommu
integer member is introduced in VirtMachineState to store the type
of the iommu in use.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-13-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements a skeleton for the smmuv3 device.
Datatypes and register definitions are introduced. The MMIO
region, the interrupts and the queue are initialized.
Only the MMIO read operation is implemented here.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the page table walk for VMSAv8-64.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Message-id: 1524665762-31355-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We set up the infrastructure to enumerate all the PCI devices
attached to the SMMU and create an associated IOMMU memory
region and address space.
Those info are stored in SMMUDevice objects. The devices are
grouped according to the PCIBus they belong to. A hash table
indexed by the PCIBus pointer is used. Also an array indexed by
the bus number allows to find the list of SMMUDevices.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The patch introduces the smmu base device and class for the ARM
smmu. Devices for specific versions will be derived from this
base device.
We also introduce some important datatypes.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- new machine type
- extend SCLP event masks
- support configuration of consoles via -serial
- firmware improvements: non-sequential entries in boot menu, support
for indirect loading via .INS files in s390-netboot
- bugfixes and cleanups
-----BEGIN PGP SIGNATURE-----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=cYvD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180504' into staging
First s390x pull request for 2.13.
- new machine type
- extend SCLP event masks
- support configuration of consoles via -serial
- firmware improvements: non-sequential entries in boot menu, support
for indirect loading via .INS files in s390-netboot
- bugfixes and cleanups
# gpg: Signature made Fri 04 May 2018 08:19:57 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180504:
pc-bios/s390: Update firmware images
s390-ccw: force diag 308 subcode to unsigned long
pc-bios/s390-ccw/net: Add support for .INS config files
pc-bios/s390-ccw/net: Use diag308 to reset machine before jumping to the OS
pc-bios/s390-ccw/net: Split up net_load() into init, load and release parts
pc-bios/s390-ccw: fix non-sequential boot entries (enum)
pc-bios/s390-ccw: fix non-sequential boot entries (eckd)
pc-bios/s390-ccw: fix loadparm initialization and int conversion
pc-bios/s390-ccw: rename MAX_TABLE_ENTRIES to MAX_BOOT_ENTRIES
pc-bios/s390-ccw: size_t should be unsigned
hw/s390x: Allow to configure the consoles with the "-serial" parameter
s390x/kvm: cleanup calls to cpu_synchronize_state()
vfio-ccw: introduce vfio_ccw_get_device()
s390x/sclp: extend SCLP event masks to 64 bits
s390x: introduce 2.13 compat machine
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4e46dcdbd3 "PPC: Newworld: Add uninorth token register" added a TODO
which was to convert the uninorth registers hack to a proper device. Move
these registers to a new uninorth device, removing the old hacks from
mac_newworld.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Under PAPR, only the boot CPU is active when the system starts. Other cpus
must be explicitly activated using an RTAS call. The entry state for the
boot and secondary cpus isn't identical, but it has some things in common.
We're going to add a bit more common setup later, too, so to simplify
make a helper which sets up the common entry state for both boot and
secondary cpu threads.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The consoles ("sclpconsole" and "sclplmconsole") can only be configured
with "-device" and "-chardev" so far. Other machines use the convenience
option "-serial" to configure the default consoles, even for virtual
consoles like spapr-vty on the pseries machine. So let's support this
option on s390x, too. This way we can easily enable the serial console
here again with "-nodefaults", for example:
qemu-system-s390x -no-shutdown -nographic -nodefaults -serial mon:stdio
... which is way shorter than typing:
qemu-system-s390x -no-shutdown -nographic -nodefaults \
-chardev stdio,id=c1,mux=on -device sclpconsole,chardev=c1 \
-mon chardev=c1
The -serial parameter can also be used if you only want to see the QEMU
monitor on stdio without using -nodefaults, but not the console output.
That's something that is pretty impossible with the current code today:
qemu-system-s390x -no-shutdown -nographic -serial none
While we're at it, this patch also maps the second -serial option to the
"sclplmconsole", so that there is now an easy way to configure this second
console on s390x, too, for example:
qemu-system-s390x -no-shutdown -nographic -serial null -serial mon:stdio
Additionally, the new code is also smaller than the old one and we have
less s390x-specific code in vl.c :-)
I've also checked that migration still works as expected by migrating
a guest with console output back and forth between a qemu-system-s390x
that has this patch and an instance without this patch.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1524754794-28005-1-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Extend the SCLP event masks to 64 bits.
Notice that using any of the new bits results in a state that cannot be
migrated to an older version.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Message-Id: <1520507069-22179-1-git-send-email-imbrenda@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The new property ibm,dynamic-memory-v2 allows memory to be represented
in a more compact manner in device tree.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As a rule we prefer to pass PowerPCCPU instead of CPUPPCState, and this
change will make some things simpler later on.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The existing UNINState actually represents the PCI/AGP host bridge stage so
rename it accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Do this for both the uninorth main and uninorth u3 AGP buses, using the main
PCI bus for each machine (this ensures the IO addresses still match those
used by OpenBIOS).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the OpenPIC is wired up via the board, we can now remove our temporary
PIC qdev pointer property and replace it with an object link instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is in preparation for moving the PCI bus wiring inside the uninorth
host bridge devices. In the future it will be possible to remove this once the
PICs have been switched to use qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead wire up heathrow to the CPU and grackle PCI host using qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
[dwg: Added hw/hw.h #include as suggested by Philippe Mathieu-Daudé]
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last user was just removed; remove this function, accordingly.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Xen unstable (to be in 4.11) has two new dmops, relocate_memory and
pin_memory_cacheattr. Use these to set up the VGA memory, replacing the
previous calls to libxc. This allows the VGA console to work properly
when QEMU is running restricted (-xen-domid-restrict).
Wrapper functions are provided to allow QEMU to work with older versions
of Xen.
Tweak the error handling while making this change:
* Report pin_memory_cacheattr errors.
* Report errors even when DEBUG_HVM is not set. This is useful for
trying to understand why VGA is not working, since otherwise it just
fails silently.
* Fix the return values when an error occurs. The functions now
consistently return -1 and set errno.
CC: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
xc_interface_open etc. is not going to work if we have dropped
privilege, but xendevicemodel_shutdown will if everything is new
enough.
xendevicemodel_shutdown is only availabe in Xen 4.10 and later, so
provide a stub for earlier versions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
We are going to want to use the dummy xendevicemodel_handle type in
new stub functions in the CONFIG_XEN_CTRL_INTERFACE_VERSION < 41000
section. So we need to provide that definition, or (as applicable)
include the appropriate header, earlier in the file.
(Ideally the newer compatibility layers would be at the bottom of the
file, so that they can naturally benefit from the compatibility layers
for earlier version. But that's rather too much for this series.)
No functional change.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
And insist that it works.
Drop individual use of xendevicemodel_restrict and
xenforeignmemory_restrict. These are not actually effective in this
version of qemu, because qemu has a large number of fds open onto
various Xen control devices.
The restriction arrangements are still not right, because the
restriction needs to be done very late - after qemu has opened all of
its control fds.
xentoolcore_restrict_all and xentoolcore.h are available in Xen 4.10
and later, only. Provide a compatibility stub. And drop the
compatibility stubs for the old functions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
The superio device has a limit on the number of serial
ports it supports which is really only there because
it has a fixed-size array serial[]. This limit isn't
related particularly to the global MAX_SERIAL_PORTS limit,
so use a different #define for it.
(In practice the users of superio only ever want 2 serial ports.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-12-peter.maydell@linaro.org
The ISA serial port handling in serial-isa.c imposes a limit
of 4 serial ports. This is because we only know of 4 IO port
and IRQ settings for them, and is unrelated to the generic
MAX_SERIAL_PORTS limit, though they happen to both be set at
4 currently.
Use a new MAX_ISA_SERIAL_PORTS wherever that is the correct
limit to be checking against.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-11-peter.maydell@linaro.org
Turn the newly added subsection off for old machine types
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We would like to have different behavior for passthrough devices
depending on the SCSI version they expose. To prepare for that,
allow the user of emulated devices to specify the desired SCSI
level, and adjust the emulation according to the property value.
The next patch will set the level for scsi-block and scsi-generic
devices.
Based on a patch by Daniel Henrique Barboza
<danielhb@linux.vnet.ibm.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of using "1.0" as the system version of SMBIOS, we should use
mc->name for mach-virt machine type to be consistent other architectures.
With this patch, "dmidecode -t 1" (e.g., "-M virt-2.12,accel=kvm") will
show:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: virt-2.12
Serial Number: Not Specified
...
instead of:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: 1.0
Serial Number: Not Specified
...
For backward compatibility, we allow older machine types to keep "1.0"
as the default system version.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180322212318.7182-1-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux does not detect a break from this IMX serial driver as a magic
sysrq. Nor does it note a break in the port error counts.
The former is because the Linux driver uses the BRCD bit in the USR2
register to trigger the RS-232 break handler in the kernel, which is
where sysrq hooks in. The emulated UART was not setting this status
bit.
The latter is because the Linux driver expects, in addition to the BRK
bit, that the ERR bit is set when a break is read in the FIFO. A break
should also count as a frame error, so add that bit too.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Message-id: 20180320013657.25038-1-tpiepho@impinj.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make qmp_pc_dimm_device_list() return sorted by start address
list of devices so that it could be reused in places that
would need sorted list*. Reuse existing pc_dimm_built_list()
to get sorted list.
While at it hide recursive callbacks from callers, so that:
qmp_pc_dimm_device_list(qdev_get_machine(), &list);
could be replaced with simpler:
list = qmp_pc_dimm_device_list();
* follow up patch will use it in build_srat()
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> for ppc part
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All PCI devices are now QOM'ified.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The bcm2837 is pretty similar to the bcm2836, but it does have
some differences. Notably, the MPIDR affinity aff1 values it
sets for the CPUs are 0x0, rather than the 0xf that the bcm2836
uses, and if this is wrong Linux will not boot.
Rather than trying to have one device with properties that
configure it differently for the two cases, create two
separate QOM devices for the two SoCs. We use the same approach
as hw/arm/aspeed_soc.c and share code and have a data table
that might differ per-SoC. For the moment the two types don't
actually have different behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-7-peter.maydell@linaro.org
Our BCM2836 type is really a generic one that can be any of
the bcm283x family. Rename it accordingly. We change only
the names which are visible via the header file to the
rest of the QEMU code, leaving private function names
in bcm2836.c as they are.
This is a preliminary to making bcm283x be an abstract
parent class to specific types for the bcm2836 and bcm2837.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-6-peter.maydell@linaro.org
Add support for "TX complete"/TXDC interrupt generate by real HW since
it is needed to support guests other than Linux.
Based on the patch by Bill Paul as found here:
https://bugs.launchpad.net/qemu/+bug/1753314
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: Bill Paul <wpaul@windriver.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bill Paul <wpaul@windriver.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Message-id: 20180315191141.6789-2-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sabrelite machine model used by qemu-system-arm is based on the
Freescale/NXP i.MX6Q processor. This SoC has an on-board ethernet
controller which is supported in QEMU using the imx_fec.c module
(actually called imx.enet for this model.)
The include/hw/arm/fsm-imx6.h file defines the interrupt vectors for the
imx.enet device like this:
#define FSL_IMX6_ENET_MAC_1588_IRQ 118
#define FSL_IMX6_ENET_MAC_IRQ 119
According to https://www.nxp.com/docs/en/reference-manual/IMX6DQRM.pdf,
page 225, in Table 3-1. ARM Cortex A9 domain interrupt summary,
interrupts are as follows.
150 ENET MAC 0 IRQ
151 ENET MAC 0 1588 Timer interrupt
where
150 - 32 == 118
151 - 32 == 119
In other words, the vector definitions in the fsl-imx6.h file are reversed.
Fixing the interrupts alone causes problems with older Linux kernels:
The Ethernet interface will fail to probe with Linux v4.9 and earlier.
Linux v4.1 and earlier will crash due to a bug in Ethernet driver probe
error handling. This is a Linux kernel problem, not a qemu problem:
the Linux kernel only worked by accident since it requested both interrupts.
For backward compatibility, generate the Ethernet interrupt on both interrupt
lines. This was shown to work from all Linux kernel releases starting with
v3.16.
Link: https://bugs.launchpad.net/qemu/+bug/1753309
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1520723090-22130-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With all targets defining CPU_RESOLVING_TYPE, refactor
cpu_parse_cpu_model(type, cpu_model) to parse_cpu_model(cpu_model)
so that callers won't have to know internal resolving cpu
type. Place it in exec.c so it could be called from both
target independed vl.c and *-user/main.c.
That allows us to stop abusing cpu type from
MachineClass::default_cpu_type
as resolver class in vl.c which were confusing part of
cpu_parse_cpu_model().
Also with new parse_cpu_model(), the last users of cpu_init()
in null-machine.c and bsd/linux-user targets could be switched
to cpu_create() API and cpu_init() API will be removed by
follow up patch.
With no longer users left remove MachineState::cpu_model field,
new code should use MachineState::cpu_type instead and
leave cpu_model parsing to generic code in vl.c.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1518000027-274608-5-git-send-email-imammedo@redhat.com>
[ehabkost: Fix bsd-user build error]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the 40p machine you now get:
$ ppc64-softmmu/qemu-system-ppc64 -M 40p -cdrom x.iso
qemu-system-ppc64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by providing a lsi53c810_create() function that takes care
of calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Wang Xin <wangxinxin.wang@huawei.com>
Message-Id: <1517367668-25048-1-git-send-email-wangxinxin.wang@huawei.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJapqaMAAoJEL/70l94x66DQoUH/Rvg+a8giz/SrEA4P8D3Cb2z
4GNbNUUoy4oU0ltD5IAMskMwpOsvl1batE0D+pKIlfO9NV4+Cj2kpgo0p9TxoYqM
VCby3wRtx27zb5nVytC6M++iIKXmeEMqXmFw61I6umddNPSl4IR3hiHEE0DM+7dV
UPIOvJeEiazyQaw3Iw+ZctNn8dDBKc/+6oxP9xRcYTaZ6hB4G9RZkqGNNSLcJkk7
R0UotdjzIZhyWMOkjIwlpTF4sWv8gsYUV4bPYKMYho5B0Obda2dBM3I1kpA8yDa/
xZ5lheOaAVBZvM5aMIcaQPa65MO9hLyXFmhMOgyfpJhLBBz6Qpa4OLLI6DeTN+0=
=UAgA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Record-replay lockstep execution, log dumper and fixes (Alex, Pavel)
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
# gpg: Signature made Mon 12 Mar 2018 16:10:52 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
tcg: fix cpu_io_recompile
replay: update documentation
replay: save vmstate of the asynchronous events
replay: don't process async events when warping the clock
scripts/replay-dump.py: replay log dumper
replay: avoid recursive call of checkpoints
replay: check return values of fwrite
replay: push replay_mutex_lock up the call tree
replay: don't destroy mutex at exit
replay: make locking visible outside replay code
replay/replay-internal.c: track holding of replay_lock
replay/replay.c: bump REPLAY_VERSION again
replay: save prior value of the host clock
replay: added replay log format description
replay: fix save/load vm for non-empty queue
replay: fixed replay_enable_events
replay: fix processing async events
cpu-exec: fix exception_index handling
hw/i386/pc: Factor out the superio code
hw/alpha/dp264: Use the TYPE_SMC37C669_SUPERIO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# default-configs/i386-softmmu.mak
# default-configs/x86_64-softmmu.mak
there is no point to read fields here but not actually
checking them so drop it and read only header + dsdt/facs
addresses since it's needed later to fetch that tables.
With this cleanup we can get rid of AcpiFadtDescriptorRev3/
ACPI_FADT_COMMON_DEF which have no users left.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extend generic build_fadt() to support rev5.1 FADT
and reuse it for 'virt' board, it would allow to
phase out usage of AcpiFadtDescriptorRev5_1 and
later ACPI_FADT_COMMON_DEF.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be extended and reused by follow up patch for ARM target.
PS:
Since it's generic function now, don't patch FIRMWARE_CTRL, DSDT
fields if they don't point to tables since platform might not
provide them and use X_ variants instead if applicable.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
move FADT data initialization out of fadt_setup() into dedicated
init_fadt_data() that will set common for pc/q35 values in
AcpiFadtData structure and acpi_get_pm_info() will complement
it with pc/q35 specific values initialization.
That will allow to get rid of fadt_setup() and generalize
build_fadt() so it could be easily extended for rev5 and
reused by ARM target.
While at it also move facs/dsdt/xdsdt offsets from build_fadt()
arg list into AcpiFadtData, as they belong to the same dataset.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ACPI_PORT_SMI_CMD is alias for APM_CNT_IOPORT,
so make it really one instead of duplicating its value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will help to add Generic Address Structure to ACPI tables
without using packed C structures and avoid endianness
issues as API doesn't need an explicit conversion.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop duplicate in form of Acpi20GenericAddress and reuse
AcpiGenericAddress.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although linkspeed and duplex can be set in a linux guest via 'ethtool -s',
this requires custom ethtool commands for virtio-net by default.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Linkspeed and duplex settings can be set as:
'-device virtio-net,speed=10000,duplex=full'
where speed is [0...INT_MAX], and duplex is ["half"|"full"].
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtio-dev@lists.oasis-open.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In prepartion for using some of the high order feature bits, make sure that
virtio-net uses 64-bit values everywhere.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtio-dev@lists.oasis-open.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At the moment we unconditionally avoid mapping MSIX data of a BAR and
emulate MSIX table in QEMU. However it is 1) not always necessary as
a platform may provide a paravirt interface for MSIX configuration;
2) can affect the speed of MMIO access by emulating them in QEMU when
frequently accessed registers share same system page with MSIX data,
this is particularly a problem for systems with the page size bigger
than 4KB.
A new capability - VFIO_REGION_INFO_CAP_MSIX_MAPPABLE - has been added
to the kernel [1] which tells the userspace that mapping of the MSIX data
is possible now. This makes use of it so from now on QEMU tries mapping
the entire BAR as a whole and emulate MSIX on top of that.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a32295c612c57990d17fb0f41e7134394b2f35f6
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When CPU supports memory encryption feature, the property can be used to
specify the encryption object to use when launching an encrypted guest.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-23-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-20-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This function only initialize the ISA bus.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-19-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-17-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-15-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the PC87312 inherits this abstract model, we remove the I8042
instance in the PREP machine.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20180308223946.26784-14-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-13-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-12-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-11-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-10-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-9-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This matches the isa_register_ioport() prototype.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-7-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (hw/ppc)
Message-Id: <20180308223946.26784-6-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (hw/ppc)
Message-Id: <20180308223946.26784-4-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Move the header from hw/isa/ to hw/dma/
- Remove the old i386/pc dependency
- use a bool type for the high_page_enable argument
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-3-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Again... (after 07dc788054 and 9157eee1b1).
We now extract the ISA bus specific helpers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-2-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the pica61 machine you now get:
$ mips64-softmmu/qemu-system-mips64 -M pica61 -cdrom x.iso
qemu-system-mips64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520414644-11535-1-git-send-email-thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The e1000 NIC is getting old and is not a very good default for a
PCIe machine type. Change it to e1000e, which should be supported
by a good number of guests.
In particular, drivers for 82574 were added first to Linux 2.6.27 (2008)
and Windows 2008 R2. This does mean that Windows 2008 will not work
anymore with Q35 machine types and a default "-net nic -net xxx" network
configuration; it did work before because it does have an AHCI driver.
However, Windows 2008 has been declared out of main stream support
in 2015. It will get out of extended support in 2020. Windows 2008
R2 has the same end of support dates and, since the two are basically
Vista vs. Windows 7, R2 probably is more popular.
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add code needed to get a functional PCI subsytem when using in
conjunction with upstream Linux guest (4.13+). Tested to work against
"e1000e" (network adapter, using MSI interrupts) as well as
"usb-ehci" (USB controller, using legacy PCI interrupts).
Based on "i.MX6 Applications Processor Reference Manual" (Document
Number: IMX6DQRM Rev. 4) as well as corresponding dirver in Linux
kernel (circa 4.13 - 4.16 found in drivers/pci/dwc/*)
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This release renames the SiFive machines to sifive_e and sifive_u
to represent the SiFive Everywhere and SiFive Unleashed platforms.
SiFive has configurable soft-core IP, so it is intended that these
machines will be extended to enable a variety of SiFive IP blocks.
The CPU definition infrastructure has been improved and there are
now vendor CPU modules including the SiFiVe E31, E51, U34 and U54
cores. The emulation accuracy for the E series has been improved
by disabling the MMU for the E series. S mode has been disabled on
cores that only support M mode and U mode. The two Spike machines
that support two privileged ISA versions have been coalesced into
one file. This series has Signed-off-by from the core contributors.
*** Known Issues ***
* Disassembler has some checkpatch warnings for the sake of code brevity
* scripts/qemu-binfmt-conf.sh has checkpatch warnings due to line length
* PMP (Physical Memory Protection) is as-of-yet unused and needs testing
*** Changelog ***
v8.2
* Rebase
v8.1
* Fix missed case of renaming spike_v1.9 to spike_v1.9.1
v8
* Added linux-user/riscv/target_elf.h during rebase
* Make resetvec configurable and clear mpp and mie on reset
* Use SiFive E31, E51, U34 and U54 cores in SiFive machines
* Define SiFive E31, E51, U34 and U54 cores
* Refactor CPU core definition in preparation for vendor cores
* Prevent S or U mode unless S or U extensions are present
* SiFive E Series cores have no MMU
* SiFive E Series cores have U mode
* Make privileged ISA v1.10 implicit in CPU types
* Remove DRAM_BASE and EXT_IO_BASE as they vary by machine
* Correctly handle mtvec and stvec alignment with respect to RVC
* Print more machine mode state in riscv_cpu_dump_state
* Make riscv_isa_string use compact extension order method
* Fix bug introduced in v6 RISCV_CPU_TYPE_NAME macro change
* Parameterize spike v1.9.1 config string
* Coalesce spike_v1.9.1 and spike_v1.10 machines
* Rename sifive_e300 to sifive_e, and sifive_u500 to sifive_u
v7
* Make spike_v1.10 the default machine
* Rename spike_v1.9 to spike_v1.9.1 to match privileged spec version
* Remove empty target/riscv/trace-events file
* Monitor ROM 32-bit reset code needs to be target endian
* Add TARGET_TIOCGPTPEER to linux-user/riscv/termbits.h
* Add -initrd support to the virt board
* Fix naming in spike machine interface header
* Update copyright notice on RISC-V Spike machines
* Update copyright notice on RISC-V HTIF Console device
* Change CPU Core and translator to GPLv2+
* Change RISC-V Disassembler to GPLv2+
* Change SiFive Test Finisher to GPLv2+
* Change SiFive CLINT to GPLv2+
* Change SiFive PRCI to GPLv2+
* Change SiFive PLIC to GPLv2+
* Change RISC-V spike machines to GPLv2+
* Change RISC-V virt machine to GPLv2+
* Change SiFive E300 machine to GPLv2+
* Change SiFive U500 machine to GPLv2+
* Change RISC-V Hart Array to GPLv2+
* Change RISC-V HTIF device to GPLv2+
* Change SiFiveUART device to GPLv2+
v6
* Drop IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Remove some unnecessary commented debug statements
* Change RISCV_CPU_TYPE_NAME to use riscv-cpu suffix
* Define all CPU variants for linux-user
* qemu_log calls require trailing \n
* Replace PLIC printfs with qemu_log
* Tear out unused HTIF code and eliminate shouting debug messages
* Fix illegal instruction when sfence.vma is passed (rs2) arguments
* Make updates to PTE accessed and dirty bits atomic
* Only require atomic PTE updates on MTTCG enabled guests
* Page fault if accessed or dirty bits can't be updated
* Fix get_physical_address PTE reads and writes on riscv32
* Remove erroneous comments from the PLIC
* Default enable MTTCG
* Make WFI less conservative
* Unify local interrupt handling
* Expunge HTIF interrupts
* Always access mstatus.mip under a lock
* Don't implement rdtime/rdtimeh in system mode (bbl emulates them)
* Implement insreth/cycleh for rv32 and always enable user-mode counters
* Add GDB stub support for reading and writing CSRs
* Rename ENABLE_CHARDEV #ifdef from HTIF code
* Replace bad HTIF ELF code with load_elf symbol callback
* Convert chained if else fault handlers to switch statements
* Use RISCV exception codes for linux-user page faults
v5
* Implement NaN-boxing for flw, set high order bits to 1
* Use float_muladd_negate_* flags to floatXX_muladd
* Use IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Fix TARGET_NR_syscalls
* Update linux-user/riscv/syscall_nr.h
* Fix FENCE.I, needs to terminate translation block
* Adjust unusual convention for interruptno >= 0
v4
* Add @riscv: since 2.12 to CpuInfoArch
* Remove misleading little-endian comment from load_kernel
* Rename cpu-model property to cpu-type
* Drop some unnecessary inline function attributes
* Don't allow GDB to set value of x0 register
* Remove unnecessary empty property lists
* Add Test Finisher device to implement poweroff in virt machine
* Implement priv ISA v1.10 trap and sret/mret xPIE/xIE behavior
* Store fflags data in fp_status
* Purge runtime users of helper_raise_exception
* Fix validate_csr
* Tidy gen_jalr
* Tidy immediate shifts
* Add gen_exception_inst_addr_mis
* Add gen_exception_debug
* Add gen_exception_illegal
* Tidy helper_fclass_*
* Split rounding mode setting to a new function
* Enforce MSTATUS_FS via TB flags
* Implement acquire/release barrier semantics
* Use atomic operations as required
* Fix FENCE and FENCE_I
* Remove commented code from spike machines
* PAGE_WRITE permissions can be set on loads if page is already dirty
* The result of format conversion on an NaN must be a quiet NaN
* Add missing process_queued_cpu_work to riscv linux-user
* Remove float(32|64)_classify from cpu.h
* Removed nonsensical unions aliasing the same type
* Use uintN_t instead of uintN_fast_t in fpu_helper.c
* Use macros for FPU exception values in softfloat_flags_to_riscv
* Move code to set round mode into set_fp_round_mode function
* Convert set_fp_exceptions from a macro to an inline function
* Convert round mode helper into an inline function
* Make fpu_helper ieee_rm array static const
* Include cpu_mmu_index in cpu_get_tb_cpu_state flags
* Eliminate MPRV influence on mmu_index
* Remove unrecoverable do_unassigned_access function
* Only update PTE accessed and dirty bits if necessary
* Remove unnecessary tlb_flush in set_mode as mode is in mmu_idx
* Remove buggy support for misa writes. misa writes are optional
and are not implemented in any known hardware
* Always set PTE read or execute permissions during page walk
* Reorder helper function declarations to match order in helper.c
* Remove redundant variable declaration in get_physical_address
* Remove duplicated code from get_physical_address
* Use mmu_idx instead of mem_idx in riscv_cpu_get_phys_page_debug
v3
* Fix indentation in PMP and HTIF debug macros
* Fix disassembler checkpatch open brace '{' on next line errors
* Fix trailing statements on next line in decode_inst_decompress
* NOTE: the other checkpatch issues have been reviewed previously
v2
* Remove redundant NULL terminators from disassembler register arrays
* Change disassembler register name arrays to const
* Refine disassembler internal function names
* Update dates in disassembler copyright message
* Remove #ifdef CONFIG_USER_ONLY version of cpu_has_work
* Use ULL suffix on 64-bit constants
* Move riscv_cpu_mmu_index from cpu.h to helper.c
* Move riscv_cpu_hw_interrupts_pending from cpu.h to helper.c
* Remove redundant TARGET_HAS_ICE from cpu.h
* Use qemu_irq instead of void* for irq definition in cpu.h
* Remove duplicate typedef from struct CPURISCVState
* Remove redundant g_strdup from cpu_register
* Remove redundant tlb_flush from riscv_cpu_reset
* Remove redundant mode calculation from get_physical_address
* Remove redundant debug mode printf and dcsr comment
* Remove redundant clearing of MSB for bare physical addresses
* Use g_assert_not_reached for invalid mode in get_physical_address
* Use g_assert_not_reached for unreachable checks in get_physical_address
* Use g_assert_not_reached for unreachable type in raise_mmu_exception
* Return exception instead of aborting for misaligned fetches
* Move exception defines from cpu.h to cpu_bits.h
* Remove redundant breakpoint control definitions from cpu_bits.h
* Implement riscv_cpu_unassigned_access exception handling
* Log and raise exceptions for unimplemented CSRs
* Match Spike HTIF exit behavior - don’t print TEST-PASSED
* Make frm,fflags,fcsr writes trap when mstatus.FS is clear
* Use g_assert_not_reached for unreachable invalid mode
* Make hret,uret,dret generate illegal instructions
* Move riscv_cpu_dump_state and int/fpr regnames to cpu.c
* Lift interrupt flag and mask into constants in cpu_bits.h
* Change trap debugging to use qemu_log_mask LOG_TRACE
* Change CSR debugging to use qemu_log_mask LOG_TRACE
* Change PMP debugging to use qemu_log_mask LOG_TRACE
* Remove commented code from pmp.c
* Change CpuInfoRISCV qapi schema docs to Since 2.12
* Change RV feature macro to use target_ulong cast
* Remove riscv_feature and instead use misa extension flags
* Make riscv_flush_icache_syscall a no-op
* Undo checkpatch whitespace fixes in unrelated linux-user code
* Remove redudant constants and tidy up cpu_bits.h
* Make helper_fence_i a no-op
* Move include "exec/cpu-all" to end of cpu.h
* Rename set_privilege to riscv_set_mode
* Move redundant forward declaration for cpu_riscv_translate_address
* Remove TCGV_UNUSED from riscv_translate_init
* Add comment to pmp.c stating the code is untested and currently unused
* Use ctz to simplify decoding of PMP NAPOT address ranges
* Change pmp_is_in_range to use than equal for end addresses
* Fix off by one error in pmp_update_rule
* Rearrange PMP_DEBUG so that formatting is compile-time checked
* Rearrange trap debugging so that formatting is compile-time checked
* Rearrange PLIC debugging so that formatting is compile-time checked
* Use qemu_log/qemu_log_mask for HTIF logging and debugging
* Move exception and interrupt names into cpu.c
* Add Palmer Dabbelt as a RISC-V Maintainer
* Rebase against current qemu master branch
v1
* initial version based on forward port from riscv-qemu repository
*** Background ***
"RISC-V is an open, free ISA enabling a new era of processor innovation
through open standard collaboration. Born in academia and research,
RISC-V ISA delivers a new level of free, extensible software and
hardware freedom on architecture, paving the way for the next 50 years
of computing design and innovation."
The QEMU RISC-V port has been developed and maintained out-of-tree for
several years by Sagar Karandikar and Bastian Koppelmann. The RISC-V
Privileged specification has evolved substantially over this period but
has recently been solidifying. The RISC-V Base ISA has been frozon for
some time and the Privileged ISA, GCC toolchain and Linux ABI are now
quite stable. I have recently joined Sagar and Bastian as a RISC-V QEMU
Maintainer and hope to support upstreaming the port.
There are multiple vendors taping out, preparing to ship, or shipping
silicon that implements the RISC-V Privileged ISA Version 1.10. There
are also several RISC-V Soft-IP cores implementing Privileged ISA
Version 1.10 that run on FPGA such as SiFive's Freedom U500 Platform
and the U54‑MC RISC-V Core IP, among many more implementations from a
variety of vendors. See https://riscv.org/ for more details.
RISC-V support was upstreamed in binutils 2.28 and GCC 7.1 in the first
half of 2016. RISC-V support is now available in LLVM top-of-tree and
the RISC-V Linux port was accepted into Linux 4.15-rc1 late last year
and is available in the Linux 4.15 release. GLIBC 2.27 added support
for the RISC-V ISA running on Linux (requires at least binutils-2.30,
gcc-7.3.0, and linux-4.15). We believe it is timely to submit the
RISC-V QEMU port for upstream review with the goal of incorporating
RISC-V support into the upcoming QEMU 2.12 release.
The RISC-V QEMU port is still under active development, mostly with
respect to device emulation, the addition of Hypervisor support as
specified in the RISC-V Draft Privileged ISA Version 1.11, and Vector
support once the first draft is finalized later this year. We believe
now is the appropriate time for RISC-V QEMU development to be carried
out in the main QEMU repository as the code will benefit from more
rigorous review. The RISC-V QEMU port currently supports all the ISA
extensions that have been finalized and frozen in the Base ISA.
Blog post about recent additions to RISC-V QEMU: https://goo.gl/fJ4zgk
The RISC-V QEMU wiki: https://github.com/riscv/riscv-qemu/wiki
Instructions for building a busybox+dropbear root image, BBL (Berkeley
Boot Loader) and linux kernel image for use with the RISC-V QEMU
'virt' machine: https://github.com/michaeljclark/busybear-linux
*** Overview ***
The RISC-V QEMU port implements the following specifications:
* RISC-V Instruction Set Manual Volume I: User-Level ISA Version 2.2
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.9.1
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.10
The RISC-V QEMU port supports the following instruction set extensions:
* RV32GC with Supervisor-mode and User-mode (RV32IMAFDCSU)
* RV64GC with Supervisor-mode and User-mode (RV64IMAFDCSU)
The RISC-V QEMU port adds the following targets to QEMU:
* riscv32-softmmu
* riscv64-softmmu
* riscv32-linux-user
* riscv64-linux-user
The RISC-V QEMU port supports the following hardware:
* HTIF Console (Host Target Interface)
* SiFive CLINT (Core Local Interruptor) for Timer interrupts and IPIs
* SiFive PLIC (Platform Level Interrupt Controller)
* SiFive Test (Test Finisher) for exiting simulation
* SiFive UART, PRCI, AON, PWM, QSPI support is partially implemented
* VirtIO MMIO (GPEX PCI support will be added in a future patch)
* Generic 16550A UART emulation using 'hw/char/serial.c'
* MTTCG and SMP support (PLIC and CLINT) on the 'virt' machine
The RISC-V QEMU full system emulator supports 5 machines:
* 'spike_v1.9.1', CLINT, PLIC, HTIF console, config-string, Priv v1.9.1
* 'spike_v1.10', CLINT, PLIC, HTIF console, device-tree, Priv v1.10
* 'sifive_e', CLINT, PLIC, SiFive UART, HiFive1 compat, Priv v1.10
* 'sifive_u', CLINT, PLIC, SiFive UART, device-tree, Priv v1.10
* 'virt', CLINT, PLIC, 16550A UART, VirtIO, device-tree, Priv v1.10
This is a list of RISC-V QEMU Port Contributors:
* Alex Suykov
* Andreas Schwab
* Antony Pavlov
* Bastian Koppelmann
* Bruce Hoult
* Chih-Min Chao
* Daire McNamara
* Darius Rad
* David Abdurachmanov
* Hesham Almatary
* Ivan Griffin
* Jim Wilson
* Kito Cheng
* Michael Clark
* Palmer Dabbelt
* Richard Henderson
* Sagar Karandikar
* Shea Levy
* Stefan O'Rear
Notes:
* contributor email addresses available off-list on request.
* checkpatch has been run on all 23 patches.
* checkpatch exceptions are noted in patches that have errors.
* passes "make check" on full build for all targets
* tested riscv-linux-4.6.2 on 'spike_v1.9.1' machine
* tested riscv-linux-4.15 on 'spike_v1.10' and 'virt' machines
* tested SiFive HiFive1 binaries in 'sifive_e' machine
* tested RV64 on 32-bit i386
This patch series includes the following patches:
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWqGRpAAKCRBr8dezV+8+
T2mMAJ9ptK/7Bs3lE+Mki/ymlTPqhXtyxACfZkyfQf1mfhcXnB+oTG1RvEtblY8=
=TJc8
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-upstream-v8.2' into staging
QEMU RISC-V Emulation Support (RV64GC, RV32GC)
This release renames the SiFive machines to sifive_e and sifive_u
to represent the SiFive Everywhere and SiFive Unleashed platforms.
SiFive has configurable soft-core IP, so it is intended that these
machines will be extended to enable a variety of SiFive IP blocks.
The CPU definition infrastructure has been improved and there are
now vendor CPU modules including the SiFiVe E31, E51, U34 and U54
cores. The emulation accuracy for the E series has been improved
by disabling the MMU for the E series. S mode has been disabled on
cores that only support M mode and U mode. The two Spike machines
that support two privileged ISA versions have been coalesced into
one file. This series has Signed-off-by from the core contributors.
*** Known Issues ***
* Disassembler has some checkpatch warnings for the sake of code brevity
* scripts/qemu-binfmt-conf.sh has checkpatch warnings due to line length
* PMP (Physical Memory Protection) is as-of-yet unused and needs testing
*** Changelog ***
v8.2
* Rebase
v8.1
* Fix missed case of renaming spike_v1.9 to spike_v1.9.1
v8
* Added linux-user/riscv/target_elf.h during rebase
* Make resetvec configurable and clear mpp and mie on reset
* Use SiFive E31, E51, U34 and U54 cores in SiFive machines
* Define SiFive E31, E51, U34 and U54 cores
* Refactor CPU core definition in preparation for vendor cores
* Prevent S or U mode unless S or U extensions are present
* SiFive E Series cores have no MMU
* SiFive E Series cores have U mode
* Make privileged ISA v1.10 implicit in CPU types
* Remove DRAM_BASE and EXT_IO_BASE as they vary by machine
* Correctly handle mtvec and stvec alignment with respect to RVC
* Print more machine mode state in riscv_cpu_dump_state
* Make riscv_isa_string use compact extension order method
* Fix bug introduced in v6 RISCV_CPU_TYPE_NAME macro change
* Parameterize spike v1.9.1 config string
* Coalesce spike_v1.9.1 and spike_v1.10 machines
* Rename sifive_e300 to sifive_e, and sifive_u500 to sifive_u
v7
* Make spike_v1.10 the default machine
* Rename spike_v1.9 to spike_v1.9.1 to match privileged spec version
* Remove empty target/riscv/trace-events file
* Monitor ROM 32-bit reset code needs to be target endian
* Add TARGET_TIOCGPTPEER to linux-user/riscv/termbits.h
* Add -initrd support to the virt board
* Fix naming in spike machine interface header
* Update copyright notice on RISC-V Spike machines
* Update copyright notice on RISC-V HTIF Console device
* Change CPU Core and translator to GPLv2+
* Change RISC-V Disassembler to GPLv2+
* Change SiFive Test Finisher to GPLv2+
* Change SiFive CLINT to GPLv2+
* Change SiFive PRCI to GPLv2+
* Change SiFive PLIC to GPLv2+
* Change RISC-V spike machines to GPLv2+
* Change RISC-V virt machine to GPLv2+
* Change SiFive E300 machine to GPLv2+
* Change SiFive U500 machine to GPLv2+
* Change RISC-V Hart Array to GPLv2+
* Change RISC-V HTIF device to GPLv2+
* Change SiFiveUART device to GPLv2+
v6
* Drop IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Remove some unnecessary commented debug statements
* Change RISCV_CPU_TYPE_NAME to use riscv-cpu suffix
* Define all CPU variants for linux-user
* qemu_log calls require trailing \n
* Replace PLIC printfs with qemu_log
* Tear out unused HTIF code and eliminate shouting debug messages
* Fix illegal instruction when sfence.vma is passed (rs2) arguments
* Make updates to PTE accessed and dirty bits atomic
* Only require atomic PTE updates on MTTCG enabled guests
* Page fault if accessed or dirty bits can't be updated
* Fix get_physical_address PTE reads and writes on riscv32
* Remove erroneous comments from the PLIC
* Default enable MTTCG
* Make WFI less conservative
* Unify local interrupt handling
* Expunge HTIF interrupts
* Always access mstatus.mip under a lock
* Don't implement rdtime/rdtimeh in system mode (bbl emulates them)
* Implement insreth/cycleh for rv32 and always enable user-mode counters
* Add GDB stub support for reading and writing CSRs
* Rename ENABLE_CHARDEV #ifdef from HTIF code
* Replace bad HTIF ELF code with load_elf symbol callback
* Convert chained if else fault handlers to switch statements
* Use RISCV exception codes for linux-user page faults
v5
* Implement NaN-boxing for flw, set high order bits to 1
* Use float_muladd_negate_* flags to floatXX_muladd
* Use IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Fix TARGET_NR_syscalls
* Update linux-user/riscv/syscall_nr.h
* Fix FENCE.I, needs to terminate translation block
* Adjust unusual convention for interruptno >= 0
v4
* Add @riscv: since 2.12 to CpuInfoArch
* Remove misleading little-endian comment from load_kernel
* Rename cpu-model property to cpu-type
* Drop some unnecessary inline function attributes
* Don't allow GDB to set value of x0 register
* Remove unnecessary empty property lists
* Add Test Finisher device to implement poweroff in virt machine
* Implement priv ISA v1.10 trap and sret/mret xPIE/xIE behavior
* Store fflags data in fp_status
* Purge runtime users of helper_raise_exception
* Fix validate_csr
* Tidy gen_jalr
* Tidy immediate shifts
* Add gen_exception_inst_addr_mis
* Add gen_exception_debug
* Add gen_exception_illegal
* Tidy helper_fclass_*
* Split rounding mode setting to a new function
* Enforce MSTATUS_FS via TB flags
* Implement acquire/release barrier semantics
* Use atomic operations as required
* Fix FENCE and FENCE_I
* Remove commented code from spike machines
* PAGE_WRITE permissions can be set on loads if page is already dirty
* The result of format conversion on an NaN must be a quiet NaN
* Add missing process_queued_cpu_work to riscv linux-user
* Remove float(32|64)_classify from cpu.h
* Removed nonsensical unions aliasing the same type
* Use uintN_t instead of uintN_fast_t in fpu_helper.c
* Use macros for FPU exception values in softfloat_flags_to_riscv
* Move code to set round mode into set_fp_round_mode function
* Convert set_fp_exceptions from a macro to an inline function
* Convert round mode helper into an inline function
* Make fpu_helper ieee_rm array static const
* Include cpu_mmu_index in cpu_get_tb_cpu_state flags
* Eliminate MPRV influence on mmu_index
* Remove unrecoverable do_unassigned_access function
* Only update PTE accessed and dirty bits if necessary
* Remove unnecessary tlb_flush in set_mode as mode is in mmu_idx
* Remove buggy support for misa writes. misa writes are optional
and are not implemented in any known hardware
* Always set PTE read or execute permissions during page walk
* Reorder helper function declarations to match order in helper.c
* Remove redundant variable declaration in get_physical_address
* Remove duplicated code from get_physical_address
* Use mmu_idx instead of mem_idx in riscv_cpu_get_phys_page_debug
v3
* Fix indentation in PMP and HTIF debug macros
* Fix disassembler checkpatch open brace '{' on next line errors
* Fix trailing statements on next line in decode_inst_decompress
* NOTE: the other checkpatch issues have been reviewed previously
v2
* Remove redundant NULL terminators from disassembler register arrays
* Change disassembler register name arrays to const
* Refine disassembler internal function names
* Update dates in disassembler copyright message
* Remove #ifdef CONFIG_USER_ONLY version of cpu_has_work
* Use ULL suffix on 64-bit constants
* Move riscv_cpu_mmu_index from cpu.h to helper.c
* Move riscv_cpu_hw_interrupts_pending from cpu.h to helper.c
* Remove redundant TARGET_HAS_ICE from cpu.h
* Use qemu_irq instead of void* for irq definition in cpu.h
* Remove duplicate typedef from struct CPURISCVState
* Remove redundant g_strdup from cpu_register
* Remove redundant tlb_flush from riscv_cpu_reset
* Remove redundant mode calculation from get_physical_address
* Remove redundant debug mode printf and dcsr comment
* Remove redundant clearing of MSB for bare physical addresses
* Use g_assert_not_reached for invalid mode in get_physical_address
* Use g_assert_not_reached for unreachable checks in get_physical_address
* Use g_assert_not_reached for unreachable type in raise_mmu_exception
* Return exception instead of aborting for misaligned fetches
* Move exception defines from cpu.h to cpu_bits.h
* Remove redundant breakpoint control definitions from cpu_bits.h
* Implement riscv_cpu_unassigned_access exception handling
* Log and raise exceptions for unimplemented CSRs
* Match Spike HTIF exit behavior - don’t print TEST-PASSED
* Make frm,fflags,fcsr writes trap when mstatus.FS is clear
* Use g_assert_not_reached for unreachable invalid mode
* Make hret,uret,dret generate illegal instructions
* Move riscv_cpu_dump_state and int/fpr regnames to cpu.c
* Lift interrupt flag and mask into constants in cpu_bits.h
* Change trap debugging to use qemu_log_mask LOG_TRACE
* Change CSR debugging to use qemu_log_mask LOG_TRACE
* Change PMP debugging to use qemu_log_mask LOG_TRACE
* Remove commented code from pmp.c
* Change CpuInfoRISCV qapi schema docs to Since 2.12
* Change RV feature macro to use target_ulong cast
* Remove riscv_feature and instead use misa extension flags
* Make riscv_flush_icache_syscall a no-op
* Undo checkpatch whitespace fixes in unrelated linux-user code
* Remove redudant constants and tidy up cpu_bits.h
* Make helper_fence_i a no-op
* Move include "exec/cpu-all" to end of cpu.h
* Rename set_privilege to riscv_set_mode
* Move redundant forward declaration for cpu_riscv_translate_address
* Remove TCGV_UNUSED from riscv_translate_init
* Add comment to pmp.c stating the code is untested and currently unused
* Use ctz to simplify decoding of PMP NAPOT address ranges
* Change pmp_is_in_range to use than equal for end addresses
* Fix off by one error in pmp_update_rule
* Rearrange PMP_DEBUG so that formatting is compile-time checked
* Rearrange trap debugging so that formatting is compile-time checked
* Rearrange PLIC debugging so that formatting is compile-time checked
* Use qemu_log/qemu_log_mask for HTIF logging and debugging
* Move exception and interrupt names into cpu.c
* Add Palmer Dabbelt as a RISC-V Maintainer
* Rebase against current qemu master branch
v1
* initial version based on forward port from riscv-qemu repository
*** Background ***
"RISC-V is an open, free ISA enabling a new era of processor innovation
through open standard collaboration. Born in academia and research,
RISC-V ISA delivers a new level of free, extensible software and
hardware freedom on architecture, paving the way for the next 50 years
of computing design and innovation."
The QEMU RISC-V port has been developed and maintained out-of-tree for
several years by Sagar Karandikar and Bastian Koppelmann. The RISC-V
Privileged specification has evolved substantially over this period but
has recently been solidifying. The RISC-V Base ISA has been frozon for
some time and the Privileged ISA, GCC toolchain and Linux ABI are now
quite stable. I have recently joined Sagar and Bastian as a RISC-V QEMU
Maintainer and hope to support upstreaming the port.
There are multiple vendors taping out, preparing to ship, or shipping
silicon that implements the RISC-V Privileged ISA Version 1.10. There
are also several RISC-V Soft-IP cores implementing Privileged ISA
Version 1.10 that run on FPGA such as SiFive's Freedom U500 Platform
and the U54‑MC RISC-V Core IP, among many more implementations from a
variety of vendors. See https://riscv.org/ for more details.
RISC-V support was upstreamed in binutils 2.28 and GCC 7.1 in the first
half of 2016. RISC-V support is now available in LLVM top-of-tree and
the RISC-V Linux port was accepted into Linux 4.15-rc1 late last year
and is available in the Linux 4.15 release. GLIBC 2.27 added support
for the RISC-V ISA running on Linux (requires at least binutils-2.30,
gcc-7.3.0, and linux-4.15). We believe it is timely to submit the
RISC-V QEMU port for upstream review with the goal of incorporating
RISC-V support into the upcoming QEMU 2.12 release.
The RISC-V QEMU port is still under active development, mostly with
respect to device emulation, the addition of Hypervisor support as
specified in the RISC-V Draft Privileged ISA Version 1.11, and Vector
support once the first draft is finalized later this year. We believe
now is the appropriate time for RISC-V QEMU development to be carried
out in the main QEMU repository as the code will benefit from more
rigorous review. The RISC-V QEMU port currently supports all the ISA
extensions that have been finalized and frozen in the Base ISA.
Blog post about recent additions to RISC-V QEMU: https://goo.gl/fJ4zgk
The RISC-V QEMU wiki: https://github.com/riscv/riscv-qemu/wiki
Instructions for building a busybox+dropbear root image, BBL (Berkeley
Boot Loader) and linux kernel image for use with the RISC-V QEMU
'virt' machine: https://github.com/michaeljclark/busybear-linux
*** Overview ***
The RISC-V QEMU port implements the following specifications:
* RISC-V Instruction Set Manual Volume I: User-Level ISA Version 2.2
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.9.1
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.10
The RISC-V QEMU port supports the following instruction set extensions:
* RV32GC with Supervisor-mode and User-mode (RV32IMAFDCSU)
* RV64GC with Supervisor-mode and User-mode (RV64IMAFDCSU)
The RISC-V QEMU port adds the following targets to QEMU:
* riscv32-softmmu
* riscv64-softmmu
* riscv32-linux-user
* riscv64-linux-user
The RISC-V QEMU port supports the following hardware:
* HTIF Console (Host Target Interface)
* SiFive CLINT (Core Local Interruptor) for Timer interrupts and IPIs
* SiFive PLIC (Platform Level Interrupt Controller)
* SiFive Test (Test Finisher) for exiting simulation
* SiFive UART, PRCI, AON, PWM, QSPI support is partially implemented
* VirtIO MMIO (GPEX PCI support will be added in a future patch)
* Generic 16550A UART emulation using 'hw/char/serial.c'
* MTTCG and SMP support (PLIC and CLINT) on the 'virt' machine
The RISC-V QEMU full system emulator supports 5 machines:
* 'spike_v1.9.1', CLINT, PLIC, HTIF console, config-string, Priv v1.9.1
* 'spike_v1.10', CLINT, PLIC, HTIF console, device-tree, Priv v1.10
* 'sifive_e', CLINT, PLIC, SiFive UART, HiFive1 compat, Priv v1.10
* 'sifive_u', CLINT, PLIC, SiFive UART, device-tree, Priv v1.10
* 'virt', CLINT, PLIC, 16550A UART, VirtIO, device-tree, Priv v1.10
This is a list of RISC-V QEMU Port Contributors:
* Alex Suykov
* Andreas Schwab
* Antony Pavlov
* Bastian Koppelmann
* Bruce Hoult
* Chih-Min Chao
* Daire McNamara
* Darius Rad
* David Abdurachmanov
* Hesham Almatary
* Ivan Griffin
* Jim Wilson
* Kito Cheng
* Michael Clark
* Palmer Dabbelt
* Richard Henderson
* Sagar Karandikar
* Shea Levy
* Stefan O'Rear
Notes:
* contributor email addresses available off-list on request.
* checkpatch has been run on all 23 patches.
* checkpatch exceptions are noted in patches that have errors.
* passes "make check" on full build for all targets
* tested riscv-linux-4.6.2 on 'spike_v1.9.1' machine
* tested riscv-linux-4.15 on 'spike_v1.10' and 'virt' machines
* tested SiFive HiFive1 binaries in 'sifive_e' machine
* tested RV64 on 32-bit i386
This patch series includes the following patches:
# gpg: Signature made Thu 08 Mar 2018 19:40:20 GMT
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-upstream-v8.2: (23 commits)
RISC-V Build Infrastructure
SiFive Freedom U Series RISC-V Machine
SiFive Freedom E Series RISC-V Machine
SiFive RISC-V PRCI Block
SiFive RISC-V UART Device
RISC-V VirtIO Machine
SiFive RISC-V Test Finisher
RISC-V Spike Machines
SiFive RISC-V PLIC Block
SiFive RISC-V CLINT Block
RISC-V HART Array
RISC-V HTIF Console
Add symbol table callback interface to load_elf
RISC-V Linux User Emulation
RISC-V Physical Memory Protection
RISC-V TCG Code Generation
RISC-V GDB Stub
RISC-V FPU Support
RISC-V CPU Helpers
RISC-V Disassembler
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce an sccb_mask_t to be used for SCLP event masks instead of just
unsigned int or uint32_t. This will allow later to extend the mask with
more ease.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Message-Id: <1519407778-23095-3-git-send-email-imbrenda@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The other event handlers (quiesce and cpu) do not define these
handlers, and this one does nothing, so it can be removed.
Signed-off-by: Nia Alarie <nia.alarie@gmail.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20180306100721.19419-1-nia.alarie@gmail.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This provides a RISC-V Board compatible with the the SiFive Freedom U SDK.
The following machine is implemented:
- 'sifive_u'; CLINT, PLIC, UART, device-tree
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
This provides a RISC-V Board compatible with the the SiFive Freedom E SDK.
The following machine is implemented:
- 'sifive_e'; CLINT, PLIC, UART, AON, GPIO, QSPI, PWM
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Simple model of the PRCI (Power, Reset, Clock, Interrupt) to emulate
register reads made by the SDK BSP.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
QEMU model of the UART on the SiFive E300 and U500 series SOCs.
BBL supports the SiFive UART for early console access via the SBI
(Supervisor Binary Interface) and the linux kernel SBI console.
The SiFive UART implements the pre qom legacy interface consistent
with the 16550a UART in 'hw/char/serial.c'.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
RISC-V machine with device-tree, 16550a UART and VirtIO MMIO.
The following machine is implemented:
- 'virt'; CLINT, PLIC, 16550A UART, VirtIO MMIO, device-tree
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Test finisher memory mapped device used to exit simulation.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
RISC-V machines compatble with Spike aka riscv-isa-sim, the RISC-V
Instruction Set Simulator. The following machines are implemented:
- 'spike_v1.9.1'; HTIF console, config-string, Privileged ISA Version 1.9.1
- 'spike_v1.10'; HTIF console, device-tree, Privileged ISA Version 1.10
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
The PLIC (Platform Level Interrupt Controller) device provides a
parameterizable interrupt controller based on SiFive's PLIC specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
The CLINT (Core Local Interruptor) device provides real-time clock, timer
and interprocessor interrupts based on SiFive's CLINT specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Holds the state of a heterogenous array of RISC-V hardware threads.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
HTIF (Host Target Interface) provides console emulation for QEMU. HTIF
allows identical copies of BBL (Berkeley Boot Loader) and linux to run
on both Spike and QEMU. BBL provides HTIF console access via the
SBI (Supervisor Binary Interface) and the linux kernel SBI console.
The HTIT chardev implements the pre qom legacy interface consistent
with the 16550a UART in 'hw/char/serial.c'.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
The RISC-V HTIF (Host Target Interface) console device requires access
to the symbol table to locate the 'tohost' and 'fromhost' symbols.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Clark <mjc@sifive.com>
Philippe Mathieu-Daudé