This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-3-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-2-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All other peripherals' IRQs are in the format of decimal value.
Change SIFIVE_U_GEM_IRQ to be consistent.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the SiFive SPI controller model for the FU540 SoC.
The direct memory-mapped SPI flash mode is unsupported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmA+SYcPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpUAAIALa9WkjdxjZhb4FzP1OLBSTEISLEfrPE4Zk/
s5yY1wEDvH83D6fxTHv1B8tISwJ3RJn8ZhsP0c0Mb6stT7D33m7YfMFtNXBEfENX
gMgwdC2QxGMZXKGR+dIpxtYghjvuzAVN+e9w27C+s855JJ8y+chghtLuDJIbqpAk
QopftjiZix2bPYmrxlVw/A7inXL2jseJyYsgGAzIACmsGC70jK4Rk1vxrAF+2n15
D4qKOG3QLJXrfIVa8iDz/ojlVUmLWl8jnoE+oY+rjtckQHJKqodlJi5yeJxGEa3/
G7db+AIzEBge78dq7LBSJOTjoUFoQ+6Hv1QtKk2GcMKdEnsj0ng=
=NGys
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,virtio,pci: bug fixes
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 02 Mar 2021 14:19:51 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
vhost: simplify vhost_dev_init() fail_busyloop label
hw/pci: Have safer pcie_bus_realize() by checking error path
virtio-net: handle zero mac for a vdpa peer
i386/acpi: restore device paths for pre-5.1 vms
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmA3tzQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMsngf+OkbgTDouxq3qnn1K89n6j2wKlAj0
qPP+57o1sv5u5MjX0BkawXCMJfvTKJaOt/Cs8S0FaPTehfR5H0T2tL76KZBEdlEP
/+V3EC0Qmd1S47LKIOuDkV15szvnccyjpgwaL7Osjb0Eh0SxeXd4pBTc3yYtkacu
zb/srZ63U2iJZr93QwGmEJjuW57WNym6QWXF3Mrg9PFXybkXFTGumB2vZMlQc+MN
RWPTUKZKAiIr/HfdvpIETXY+HzJhylvIQ8OVWtM3XDorl48OWcOat/jyeNEVYgG3
o+gxIRnfvIL+42GkmUFbOKLzT5SV6p9EYYGLTuE1kU7nc6HWoD0CdPxA3A==
=UBVO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging
* fix --enable-fuzzing linker failures (Alexander)
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
# gpg: Signature made Thu 25 Feb 2021 14:41:56 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini-gitlab/tags/for-upstream: (29 commits)
tcg/i386: rdpmc: fix the the condtions
chardev: do not use short form boolean options in non-QemuOpts character device descriptions
vl: deprecate -writeconfig
target/i386: Add bus lock debug exception support
qom/object.c: Fix typo
target/i386: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -vnc
docs: update to show preferred boolean syntax for -chardev
qemu-options: update to show preferred boolean syntax for -vnc
qemu-options: update to show preferred boolean syntax for -incoming
qemu-options: update to show preferred boolean syntax for -netdev
qemu-options: update to show preferred boolean syntax for -spice
qemu-options: update to show preferred boolean syntax for -chardev
gdbstub: use preferred boolean option syntax
char: don't fail when client is not connected
scsi: drop 'result' argument from command_complete callback
scsi-disk: pass guest recoverable errors through even for rerror=stop
scsi-disk: pass SCSI status to scsi_handle_rw_error
scsi: introduce scsi_sense_from_errno()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After fixing the _UID value for the primary PCI root bridge in
af1b80ae it was discovered that this change updates Windows
configuration in an incompatible way causing network configuration
failure unless DHCP is used. More details provided on the list:
https://lists.gnu.org/archive/html/qemu-devel/2021-02/msg08484.html
This change reverts the _UID update from 1 to 0 for q35 and i440fx
VMs before version 5.2 to maintain the original behaviour when
upgrading.
Cc: qemu-stable@nongnu.org
Cc: qemu-devel@nongnu.org
Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Message-Id: <20210301195919.9333-1-cheptsov@ispras.ru>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: af1b80ae56 ("i386/acpi: fix inconsistent QEMU/OVMF device paths")
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current code sets an infinite timeout on SG_IO requests,
causing the guest to stall if the host experiences a frame
loss.
This patch adds an 'io_timeout' parameter for SCSIDevice to
make the SG_IO timeout configurable, and also shortens the
default timeout to 30 seconds to avoid infinite stalls.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If SMM is not supported, ACPI fixed hardware doesn't support
legacy-mode. ACPI-only platform. Where SCI_EN in PM1_CNT register is
always set.
The bit tells OS legacy mode(SCI_EN cleared) or ACPI mode(SCI_EN set).
With the next patch (setting fadt.smi_cmd = 0 when smm isn't enabled),
guest Linux tries to switch to ACPI mode, finds smi_cmd = 0, and then
fails to initialize acpi subsystem. This patch proactively fixes it.
This patch changes guest ABI. To keep compatibility, use
"smm-compat" introduced by earlier patch. If the property is true,
disable new behavior.
ACPI spec 4.8.10.1 PM1 Event Grouping
PM1 Eanble Registers
> For ACPI-only platforms (where SCI_EN is always set)
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <500f62081626997e46f96377393d3662211763a8.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following patch will introduce incompatible behavior of SMM.
Introduce a property to keep the old behavior for compatibility.
To enable smm compat, use "-global ICH9-LPC.smm-compat=on" or
"-global PIIX4_PM.smm-compat=on"
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <47254ae0b8c6cc6945422978b6b2af2d213ef891.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
- Drop redundant struct MemmapEntry (Bin)
- Fix for Coverity CID 1438965 and 1438967 (Jiaxun)
- Add MIPS bootloader API (Jiaxun)
- Use MIPS bootloader API on fuloong2e and boston machines (Jiaxun)
- Add PMON test for Loongson-3A1000 CPU (Jiaxun)
- Convert to translator API (Philippe)
- MMU cleanups (Philippe)
- Promote 128-bit multimedia registers as global ones (Philippe)
- Various cleanups/fixes on the VT82C686B southbridge (Zoltan)
-----BEGIN PGP SIGNATURE-----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=g7Kx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-20210221' into staging
MIPS patches queue
- Drop redundant struct MemmapEntry (Bin)
- Fix for Coverity CID 1438965 and 1438967 (Jiaxun)
- Add MIPS bootloader API (Jiaxun)
- Use MIPS bootloader API on fuloong2e and boston machines (Jiaxun)
- Add PMON test for Loongson-3A1000 CPU (Jiaxun)
- Convert to translator API (Philippe)
- MMU cleanups (Philippe)
- Promote 128-bit multimedia registers as global ones (Philippe)
- Various cleanups/fixes on the VT82C686B southbridge (Zoltan)
# gpg: Signature made Sun 21 Feb 2021 18:43:57 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-20210221: (43 commits)
vt82c686: Fix superio_cfg_{read,write}() functions
vt82c686: Log superio_cfg unimplemented accesses
vt82c686: Simplify by returning earlier
vt82c686: Reduce indentation by returning early
vt82c686: Remove index field of SuperIOConfig
vt82c686: Move creation of ISA devices to the ISA bridge
vt82c686: Simplify vt82c686b_realize()
vt82c686: Make vt82c686b-pm an abstract base class and add vt8231-pm based on it
vt82c686: Set user_creatable=false for VT82C686B_PM
vt82c686: Fix up power management io base and config
vt82c686: Correctly reset all registers to default values on reset
vt82c686: Correct vt82c686-pm I/O size
vt82c686: Make vt82c686-pm an I/O tracing region
vt82c686: Fix SMBus IO base and configuration registers
vt82c686: Reorganise code
vt82c686: Move superio memory region to SuperIOConfig struct
target/mips: Use GPR move functions in gen_HILO1_tx79()
target/mips: Introduce gen_load_gpr_hi() / gen_store_gpr_hi() helpers
target/mips: Rename 128-bit upper halve GPR registers
target/mips: Promote 128-bit multimedia registers as global ones
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The vt82c686b-pm model can be shared between VT82C686B and VT8231. The
only difference between the two is the device id in what we emulate so
make an abstract via-pm model by renaming appropriately and add types
for vt82c686b-pm and vt8231-pm based on it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <34969fc7be984fa070479bfb9f748993a0aef31b.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add a bootloader helper to generate simple bootloaders for kernel.
It can help us reduce inline hex hack and also keep MIPS release 6
compatibility easier.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-2-jiaxun.yang@flygoat.com>
[PMD: Restricted bl_reg enum to C source,
inverted bl_gen_write() args,
added license in hw/mips/bootloader.h]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
-----BEGIN PGP SIGNATURE-----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=ipHI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging
Pull request trivial patches 20210220
# gpg: Signature made Sat 20 Feb 2021 12:34:21 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.0-pull-request:
MAINTAINERS: Fix default-configs/ entries
target/avr/cpu: Use device_class_set_parent_realize()
hw/scsi/megasas: Remove pointless parenthesis
u2f-passthru: put it into the 'misc' category
tpm: put some tpm devices into the correct category
nvdimm: put it into the 'storage' category
vmmouse: put it into the 'input' category
virtio-pmem: put it into the 'storage' category
MAINTAINERS: add my github tree URL
Fix SPDX-License-Identifier typos
hw/block/fdc: Remove the check_media_rate property
hw/i386/xen: Remove dead code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several SPDX headers contain "SPDX-License-Identifer" (note the
missing "i" before "er"); fix these typos.
Signed-off-by: Ryan Finnie <ryan@finnie.org>
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210201200147.211914-1-ryan@finnie.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
At present there is a data_ready() callback for the SD data read
path. Let's add a receive_ready() for the SD data write path.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Create a hook in which to split out the mips and
sh4 ifdefs from cpu_io_recompile.
[AJB: s/stoped/stopped/]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210208233906.479571-3-richard.henderson@linaro.org>
Message-Id: <20210213130325.14781-12-alex.bennee@linaro.org>
This also means we don't need an extra declaration of
the structure in hw/core/cpu.h.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210208233906.479571-2-richard.henderson@linaro.org>
Message-Id: <20210213130325.14781-11-alex.bennee@linaro.org>
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector. The table goes
backwards in memory so all entries are of the form
<data>|len|<GUID>
Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.
The foot of the table is of this form and <len> for this case
describes the entire size of the table. The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.
Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents. (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)
This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
Perform device reset in the remote process when QEMU performs
device reset. This is required to reset the internal state
(like registers, etc...) of emulated devices
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7cb220a51f565dc0817bd76e2f540e89c2d2b850.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IOHUB object is added to manage PCI IRQs. It uses KVM_IRQFD
ioctl to create irqfd to injecting PCI interrupts to the guest.
IOHUB object forwards the irqfd to the remote process. Remote process
uses this fd to directly send interrupts to the guest, bypassing QEMU.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 51d5c3d54e28a68b002e3875c59599c9f5a424a1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add ProxyMemoryListener object which is used to keep the view of the RAM
in sync between QEMU and remote process.
A MemoryListener is registered for system-memory AddressSpace. The
listener sends SYNC_SYSMEM message to the remote process when memory
listener commits the changes to memory, the remote process receives
the message and processes it in the handler for SYNC_SYSMEM message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 04fe4e6a9ca90d4f11ab6f59be7652f5b086a071.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Proxy device object implements handler for PCI BAR writes and reads.
The handler uses BAR_WRITE/BAR_READ message to communicate to the
remote process with the BAR address and value to be written/read.
The remote process implements handler for BAR_WRITE/BAR_READ
message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: a8b76714a9688be5552c4c92d089bc9e8a4707ff.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The Proxy Object sends the PCI config space accesses as messages
to the remote process over the communication channel
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d3c94f4618813234655356c60e6f0d0362ff42d6.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d54edb4176361eed86b903e8f27058363b6c83b3.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Defines a PCI Device proxy object as a child of TYPE_PCI_DEVICE.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: b5186ebfedf8e557044d09a768846c59230ad3a7.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
SyncSysMemMsg message format is defined. It is used to send
file descriptors of the RAM regions to remote device.
RAM on the remote device is configured with a set of file descriptors.
Old RAM regions are deleted and new regions, each with an fd, is
added to the RAM.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7d2d1831d812e85f681e7a8ab99e032cf4704689.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Initializes the message handler function in the remote process. It is
called whenever there's an event pending on QIOChannel that registers
this function.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 99d38d8b93753a6409ac2340e858858cda59ab1b.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Defines MPQemuMsg, which is the message that is sent to the remote
process. This message is sent over QIOChannel and is used to
command the remote process to perform various tasks.
Define transmission functions used by proxy and by remote.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 56ca8bcf95195b2b195b08f6b9565b6d7410bce5.1611938319.git.jag.raman@oracle.com
[Replace struct iovec send[2] = {0} with {} to make clang happy as
suggested by Peter Maydell <peter.maydell@linaro.org>.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
x-remote-machine object sets up various subsystems of the remote
device process. Instantiate PCI host bridge object and initialize RAM, IO &
PCI memory regions.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: c537f38d17f90453ca610c6b70cf3480274e0ba1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
PCI host bridge is setup for the remote device process. It is
implemented using remote-pcihost object. It is an extension of the PCI
host bridge setup by QEMU.
Remote-pcihost configures a PCI bus which could be used by the remote
PCI device to latch on to.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 0871ba857abb2eafacde07e7fe66a3f12415bfb2.1611938319.git.jag.raman@oracle.com
[Added PCI_EXPRESS condition in hw/remote/Kconfig since remote-pcihost
needs PCIe. This solves "make check" failure on s390x. Fix suggested by
Philippe Mathieu-Daudé <philmd@redhat.com> and Thomas Huth
<thuth@redhat.com>.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We'll need to check the initial value given to spapr->gpu_numa_id when
building the rtas DT, so put it in a helper for easier access and to
avoid repetition.
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is used only in spapr_numa.c.
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This to map the PNOR from the machine init handler directly and finish
the cleanup of the LPC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-8-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ENDs allocated by OPAL for the HW thread VPs are tagged as owned by FW.
Dump the state in 'info pic'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is currently not possible to perform a strict boot from USB storage:
$ qemu-system-ppc64 -accel kvm -nodefaults -nographic -serial stdio \
-boot strict=on \
-device qemu-xhci \
-device usb-storage,drive=disk,bootindex=0 \
-blockdev driver=file,node-name=disk,filename=fedora-ppc64le.qcow2
SLOF **********************************************************************
QEMU Starting
Build Date = Jul 17 2020 11:15:24
FW Version = git-e18ddad8516ff2cf
Press "s" to enter Open Firmware.
Populating /vdevice methods
Populating /vdevice/vty@71000000
Populating /vdevice/nvram@71000001
Populating /pci@800000020000000
00 0000 (D) : 1b36 000d serial bus [ usb-xhci ]
No NVRAM common partition, re-initializing...
Scanning USB
XHCI: Initializing
USB Storage
SCSI: Looking for devices
101000000000000 DISK : "QEMU QEMU HARDDISK 2.5+"
Using default console: /vdevice/vty@71000000
Welcome to Open Firmware
Copyright (c) 2004, 2017 IBM Corporation All rights reserved.
This program and the accompanying materials are made available
under the terms of the BSD License available at
http://www.opensource.org/licenses/bsd-license.php
Trying to load: from: /pci@800000020000000/usb@0/storage@1/disk@101000000000000 ...
E3405: No such device
E3407: Load failed
Type 'boot' and press return to continue booting the system.
Type 'reset-all' and press return to reboot the system.
Ready!
0 >
The device tree handed over by QEMU to SLOF indeed contains:
qemu,boot-list =
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000 HALT";
but the device node is named usb-xhci@0, not usb@0.
This happens because the firmware names of PCI devices returned
by get_boot_devices_list() come from pcibus_get_fw_dev_path(),
while the sPAPR PHB code uses a different naming scheme for
device nodes. This inconsistency has always been there but it was
hidden for a long time because SLOF used to rename USB device
nodes, until this commit, merged in QEMU 4.2.0 :
commit 85164ad4ed
Author: Alexey Kardashevskiy <aik@ozlabs.ru>
Date: Wed Sep 11 16:24:32 2019 +1000
pseries: Update SLOF firmware image
This fixes USB host bus adapter name in the device tree to match QEMU's
one.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fortunately, sPAPR implements the firmware path provider interface.
This provides a way to override the default firmware paths.
Just factor out the sPAPR PHB naming logic from spapr_dt_pci_device()
to a helper, and use it in the sPAPR firmware path provider hook.
Fixes: 85164ad4ed ("pseries: Update SLOF firmware image")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210122170157.246374-1-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At least some s390 cpu models support "Protected Virtualization" (PV),
a mechanism to protect guests from eavesdropping by a compromised
hypervisor.
This is similar in function to other mechanisms like AMD's SEV and
POWER's PEF, which are controlled by the "confidential-guest-support"
machine option. s390 is a slightly special case, because we already
supported PV, simply by using a CPU model with the required feature
(S390_FEAT_UNPACK).
To integrate this with the option used by other platforms, we
implement the following compromise:
- When the confidential-guest-support option is set, s390 will
recognize it, verify that the CPU can support PV (failing if not)
and set virtio default options necessary for encrypted or protected
guests, as on other platforms. i.e. if confidential-guest-support
is set, we will either create a guest capable of entering PV mode,
or fail outright.
- If confidential-guest-support is not set, guests might still be
able to enter PV mode, if the CPU has the right model. This may be
a little surprising, but shouldn't actually be harmful.
To start a guest supporting Protected Virtualization using the new
option use the command line arguments:
-object s390-pv-guest,id=pv0 -machine confidential-guest-support=pv0
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Some upcoming POWER machines have a system called PEF (Protected
Execution Facility) which uses a small ultravisor to allow guests to
run in a way that they can't be eavesdropped by the hypervisor. The
effect is roughly similar to AMD SEV, although the mechanisms are
quite different.
Most of the work of this is done between the guest, KVM and the
ultravisor, with little need for involvement by qemu. However qemu
does need to tell KVM to allow secure VMs.
Because the availability of secure mode is a guest visible difference
which depends on having the right hardware and firmware, we don't
enable this by default. In order to run a secure guest you need to
create a "pef-guest" object and set the confidential-guest-support
property to point to it.
Note that this just *allows* secure guests, the architecture of PEF is
such that the guest still needs to talk to the ultravisor to enter
secure mode. Qemu has no direct way of knowing if the guest is in
secure mode, and certainly can't know until well after machine
creation time.
To start a PEF-capable guest, use the command line options:
-object pef-guest,id=pef0 -machine confidential-guest-support=pef0
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently the "memory-encryption" property is only looked at once we
get to kvm_init(). Although protection of guest memory from the
hypervisor isn't something that could really ever work with TCG, it's
not conceptually tied to the KVM accelerator.
In addition, the way the string property is resolved to an object is
almost identical to how a QOM link property is handled.
So, create a new "confidential-guest-support" link property which sets
this QOM interface link directly in the machine. For compatibility we
keep the "memory-encryption" property, but now implemented in terms of
the new property.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
add a new optional interface to CPUClass, which allows accelerators
to extend the CPUClass with additional accelerator-specific
initializations.
This will allow to separate the target cpu code that is specific
to each accelerator, and register it automatically with object
hierarchy lookup depending on accelerator code availability,
as part of the accel_init_interfaces() initialization step.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210204163931.7358-19-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
we cannot in principle make the TCG Operations field definitions
conditional on CONFIG_TCG in code that is included by both common_ss
and specific_ss modules.
Therefore, what we can do safely to restrict the TCG fields to TCG-only
builds, is to move all tcg cpu operations into a separate header file,
which is only included by TCG, target-specific code.
This leaves just a NULL pointer in the cpu.h for the non-TCG builds.
This also tidies up the code in all targets a bit, having all TCG cpu
operations neatly contained by a dedicated data struct.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210204163931.7358-16-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
commit 568496c0c0 ("cpu: Add callback to check architectural") and
commit 3826121d92 ("target-arm: Implement checking of fired")
introduced an ARM-specific hack for cpu_check_watchpoint.
Make debug_check_watchpoint optional, and move it to tcg_ops.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210204163931.7358-15-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
commit 4061200059 ("arm: Correctly handle watchpoints for BE32 CPUs")
introduced this ARM-specific, TCG-specific hack to adjust the address,
before checking it with cpu_check_watchpoint.
Make adjust_watchpoint_address optional and move it to tcg_ops.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210204163931.7358-14-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
make it consistently SOFTMMU-only.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[claudio: make the field presence in cpu.h unconditional, removing the ifdefs]
Message-Id: <20210204163931.7358-12-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[claudio: wrap target code around CONFIG_TCG and !CONFIG_USER_ONLY]
avoiding its use in headers used by common_ss code (should be poisoned).
Note: need to be careful with the use of CONFIG_USER_ONLY,
Message-Id: <20210204163931.7358-11-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
move away TCG-only code, make it compile only on TCG.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[claudio: moved the prototypes from hw/core/cpu.h to exec/cpu-all.h]
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210204163931.7358-4-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The TCG-specific CPU methods will be moved to a separate struct,
to make it easier to move accel-specific code outside generic CPU
code in the future. Start by moving tcg_initialize().
The new CPUClass.tcg_opts field may eventually become a pointer,
but keep it an embedded struct for now, to make code conversion
easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
[claudio: move TCGCpuOperations inside include/hw/core/cpu.h]
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210204163931.7358-2-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Qemu's ACPI table generation sets the fields OEM ID and OEM table ID
to "BOCHS " and "BXPCxxxx" where "xxxx" is replaced by the ACPI
table name.
Some games like Red Dead Redemption 2 seem to check the ACPI OEM ID
and OEM table ID for the strings "BOCHS" and "BXPC" and if they are
found, the game crashes(this may be an intentional detection
mechanism to prevent playing the game in a virtualized environment).
This patch allows you to override these default values.
The feature can be used in this manner:
qemu -machine oem-id=ABCDEF,oem-table-id=GHIJKLMN
The oem-id string can be up to 6 bytes in size, and the
oem-table-id string can be up to 8 bytes in size. If the string are
smaller than their respective sizes they will be padded with space.
If either of these parameters is not set, the current default values
will be used for the one missing.
Note that the the OEM Table ID field will not be extended with the
name of the table, but will use either the default name or the user
provided one.
This does not affect the -acpitable option (for user-defined ACPI
tables), which has precedence over -machine option.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210119003216.17637-3-posteuca@mutex.one>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This property can be useful for distros to set up known-good ROM sizes for
migration purposes. The VM will fail to start if the ROM is too large,
and migration compatibility will not be broken if the ROM is too small.
Note that even though romsize is a uint32_t, it has to be between 1
(because empty ROM files are not accepted, and romsize must be greater
than the file) and 2^31 (because values above are not powers of two and
are rejected).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201218182736.1634344-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210203131828.156467-3-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Displaying rendered resources requires blocking qemu GPU to avoid extra
framebuffer copies. For an external display, via Spice currently, there
is a callback to block/unblock the rendering in the same thread.
But with the vhost-user-gpu backend, the qemu process doesn't handle
the rendering itself, and the blocking callback isn't effective.
Instead, the backend must be notified when the display code is done.
Fix this by adding a new GraphicHwOps callback to indicate the GL state
is flushed, and we are done manipulating the shared GL resources. Call
it from gtk and spice display.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-19-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The next patch will notify the GL context got flush, which will resume
the queue processing. However, if this happens within the caller
context, it will end up with a stack overflow flush/update loop.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-18-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Avoid using a magic number (4) everywhere for the number of chip
selects supported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 20210129132323.30946-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now no users are setting the frq properties on the CMSDK timer,
dualtimer, watchdog or ARMSSE SoC devices, we can remove the
properties and the struct fields that back them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-25-peter.maydell@linaro.org
Message-id: 20210121190622.22000-25-peter.maydell@linaro.org
The old-style convenience function cmsdk_apb_timer_create() for
creating CMSDK_APB_TIMER objects is used in only two places in
mps2.c. Most of the rest of the code in that file uses the new
"initialize in place" coding style.
We want to connect up a Clock object which should be done between the
object creation and realization; rather than adding a Clock* argument
to the convenience function, convert the timer creation code in
mps2.c to the same style as is used already for the watchdog,
dualtimer and other devices, and delete the now-unused convenience
function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-13-peter.maydell@linaro.org
Message-id: 20210121190622.22000-13-peter.maydell@linaro.org
Create two input clocks on the ARMSSE devices, one for the normal
MAINCLK, and one for the 32KHz S32KCLK, and wire these up to the
appropriate devices. The old property-based clock frequency setting
will remain in place until conversion is complete.
This is a migration compatibility break for machines mps2-an505,
mps2-an521, musca-a, musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-12-peter.maydell@linaro.org
Message-id: 20210121190622.22000-12-peter.maydell@linaro.org
While we transition the ARMSSE code from integer properties
specifying clock frequencies to Clock objects, we want to have the
device provide both at once. We want the final name of the main
input Clock to be "MAINCLK", following the hardware name.
Unfortunately creating an input Clock with a name X creates an
under-the-hood QOM property X; for "MAINCLK" this clashes with the
existing UINT32 property of that name.
Rename the UINT32 property to MAINCLK_FRQ so it can coexist with the
MAINCLK Clock; once the transition is complete MAINCLK_FRQ will be
deleted.
Commit created with:
perl -p -i -e 's/MAINCLK/MAINCLK_FRQ/g' hw/arm/{armsse,mps2-tz,musca}.c include/hw/arm/armsse.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-11-peter.maydell@linaro.org
Message-id: 20210121190622.22000-11-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_TIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the
wdogclk-frq property to using the Clock once all the users of this
device have been converted to wire up the Clock.
This is a migration compatibility break for machines mps2-an385,
mps2-an386, mps2-an500, mps2-an511, mps2-an505, mps2-an521, musca-a,
musca-b1, lm3s811evb, lm3s6965evb.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-10-peter.maydell@linaro.org
Message-id: 20210121190622.22000-10-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_DUALTIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the pclk-frq
property to using the Clock once all the users of this device have
been converted to wire up the Clock.
We take the opportunity to correct the name of the clock input to
match the hardware -- the dual timer names the clock which drives the
timers TIMCLK. (It does also have a 'pclk' input, which is used only
for the register and APB bus logic; on the SSE-200 these clocks are
both connected together.)
This is a migration compatibility break for machines mps2-an385,
mps2-an386, mps2-an500, mps2-an511, mps2-an505, mps2-an521, musca-a,
musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-9-peter.maydell@linaro.org
Message-id: 20210121190622.22000-9-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_TIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the pclk-frq
property to using the Clock once all the users of this device have
been converted to wire up the Clock.
Since the device doesn't already have a doc comment for its "QEMU
interface", we add one including the new Clock.
This is a migration compatibility break for machines mps2-an505,
mps2-an521, musca-a, musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-8-peter.maydell@linaro.org
Message-id: 20210121190622.22000-8-peter.maydell@linaro.org
The state struct for the CMSDK APB timer device doesn't follow our
usual naming convention of camelcase -- "CMSDK" and "APB" are both
acronyms, but "TIMER" is not so should not be all-uppercase.
Globally rename the struct to "CMSDKAPBTimer" (bringing it into line
with CMSDKAPBWatchdog and CMSDKAPBDualTimer; CMSDKAPBUART remains
as-is because "UART" is an acronym).
Commit created with:
perl -p -i -e 's/CMSDKAPBTIMER/CMSDKAPBTimer/g' hw/timer/cmsdk-apb-timer.c include/hw/arm/armsse.h include/hw/timer/cmsdk-apb-timer.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-7-peter.maydell@linaro.org
Message-id: 20210121190622.22000-7-peter.maydell@linaro.org
Add a function for checking whether a clock has a source. This is
useful for devices which have input clocks that must be wired up by
the board as it allows them to fail in realize rather than ploughing
on with a zero-period clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-3-peter.maydell@linaro.org
Message-id: 20210121190622.22000-3-peter.maydell@linaro.org
The ptimer API currently provides two methods for setting the period:
ptimer_set_period(), which takes a period in nanoseconds, and
ptimer_set_freq(), which takes a frequency in Hz. Neither of these
lines up nicely with the Clock API, because although both the Clock
and the ptimer track the frequency using a representation of whole
and fractional nanoseconds, conversion via either period-in-ns or
frequency-in-Hz will introduce a rounding error.
Add a new function ptimer_set_period_from_clock() which takes the
Clock object directly to avoid the rounding issues. This includes a
facility for the user to specify that there is a frequency divider
between the Clock proper and the timer, as some timer devices like
the CMSDK APB dualtimer need this.
To avoid having to drag in clock.h from ptimer.h we add the Clock
type to typedefs.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-2-peter.maydell@linaro.org
Message-id: 20210121190622.22000-2-peter.maydell@linaro.org
Add PCI interface support for PVPANIC device. Create a new file pvpanic-pci.c
where the PCI specific routines reside and update the build system with the new
files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To ease the PCI device addition in next patches, split the code as follows:
- generic code (read/write/setup) is being kept in pvpanic.c
- ISA dependent code moved to pvpanic-isa.c
Also, rename:
- ISA_PVPANIC_DEVICE -> PVPANIC_ISA_DEVICE.
- TYPE_PVPANIC -> TYPE_PVPANIC_ISA.
- MemoryRegion io -> mr.
- pvpanic_ioport_* in pvpanic_*.
Update the build system with the new files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add secure pl061 for reset/power down machine from
the secure world (Arm Trusted Firmware). Connect it
with gpio-pwr driver.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
[PMM: Added mention of the new device to the documentation]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU coding convention prefers spaces over tabs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-15-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Log all traffic of a specific usb device to a pcap file for later
inspection. File format is compatible with linux usb monitor.
Usage:
qemu -device usb-${somedevice},pcap=file.pcap
wireshark file.pcap
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210119194452.2148048-1-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The next-cube.h file is missing the usual copyright-and-license
header; add it (same as the next-cube.c one).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-12-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Make the next_irq function be GPIO inputs to the NEXT_PC
device, rather than a freestanding set of qemu_irq lines.
This fixes a minor Coverity issue where it correctly points
out the trivial memory leak of the memory allocated in the
call to qemu_allocate_irqs().
Fixes: CID 1421962
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-8-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The next_irq() function is global, but isn't actually used anywhere
outside next-cube.c. Make it static.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-2-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The function is called only inside spapr_hcall.c.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210114180628.1675603-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This whitespace was messing with lots of diffs if you happen
to use an editor that eliminates trailing whitespaces on file
save.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210114180628.1675603-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit 1e8b5b1aa1 ("spapr: Allow memory unplug to always succeed")
trying to unplug memory from a guest that doesn't support it (eg. rhel6)
no longer generates an error like it used to. Instead, it leaves the
memory around : only a subsequent reboot or manual use of drmgr within
the guest can complete the hot-unplug sequence. A flag was added to
SpaprMachineClass so that this new behavior only applies to the default
machine type.
We can do better. CAS processes all pending hot-unplug requests. This
means that we don't really care about what the guest supports if
the hot-unplug request happens before CAS.
All guests that we care for, even old ones, set enough bits in OV5
that lead to a non-empty bitmap in spapr->ov5_cas. Use that as a
heuristic to decide if CAS has already occured or not.
Always accept unplug requests that happen before CAS since CAS will
process them. Restore the previous behavior of rejecting them after
CAS when we know that the guest doesn't support memory hot-unplug.
This behavior is suitable for all machine types : this allows to
drop the pre_6_0_memory_unplug flag.
Fixes: 1e8b5b1aa1 ("spapr: Allow memory unplug to always succeed")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <161012708715.801107.11418801796987916516.stgit@bahia.lan>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now we've converted all the callsites to directly create the QOM UIC
device themselves, the ppcuic_init() function is unused and can be
removed. The enum defining PPCUIC symbolic constants can be moved
to the ppc-uic.h header where it more naturally belongs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20210108171212.16500-5-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This PR:
- Fixes some issues with the m25p80
- Improves GDB support for RISC-V
- Fixes some Linux boot issues, specifiaclly 32-bit boot failures
- Enforces PMP exceptions correctly
- Fixes some Coverity issues
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmAEsc8ACgkQIeENKd+X
cFT3cwf+NNPVzjl0T7OEI1XxL6UCEkX6/cgxPv+ChjMCRlfnts9iHMWyeiO8E4mG
qORpLe5YCT+tAVA+rKKVu8ADp5pE9sdRp8gO7TMhZaHi3r1CQpsleZWE9R0IoBIu
eiENTgFHIV3VFcJQpOgorqCJ9qRnx2pPjjwf0H8G/hMYcgaMAzz+rdK+XvP0cCaY
/U78g0pPWx1MwdIFhhhaxAhbthnv6TkWf6oSPeGezDaAp1tnNg/Bd+FL6pT0vAM9
Mhr39TqrOJ/R0npsTngVe5Rl23Gqh3/1AYOnZz1+e9J0pB4YXnxwwiuV0t8lZnsw
OFIGXm7V3dL8BQ4ycZojlIkmML2Siw==
=3q/k
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210117-3' into staging
First RISC-V PR for 6.0
This PR:
- Fixes some issues with the m25p80
- Improves GDB support for RISC-V
- Fixes some Linux boot issues, specifiaclly 32-bit boot failures
- Enforces PMP exceptions correctly
- Fixes some Coverity issues
# gpg: Signature made Sun 17 Jan 2021 21:53:19 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210117-3:
riscv: Pass RISCVHartArrayState by pointer
target/riscv: Remove built-in GDB XML files for CSRs
target/riscv: Generate the GDB XML file for CSR registers dynamically
target/riscv: Add CSR name in the CSR function table
target/riscv: Make csr_ops[CSR_TABLE_SIZE] external
hw/misc/sifive_u_otp: handling the fails of blk_pread and blk_pwrite
hw/riscv: sifive_u: Use SIFIVE_U_CPU for mc->default_cpu_type
target/riscv/pmp: Raise exception if no PMP entry is configured
RISC-V: Place DTB at 3GB boundary instead of 4GB
gdb: riscv: Add target description
hw/block: m25p80: Implement AAI-WP command support for SST flashes
hw/block: m25p80: Don't write to flash if write is disabled
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AML needs Address Translation offset to describe how a bridge translates
addresses accross the bridge when using an address descriptor, and
especially on ARM, the translation offset of pio resource is usually
non zero.
Therefore, it's necessary to pass offset for pio, mmio32, mmio64 and bus
number into build_crs.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20210114100643.10617-4-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We were accidently passing RISCVHartArrayState by value instead of
pointer. The type is 824 bytes long so let's correct that and pass it by
pointer instead.
Fixes: Coverity CID 1438099
Fixes: Coverity CID 1438100
Fixes: Coverity CID 1438101
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Message-id: f3e04424723e0e222769991896cc82308fd23f76.1610751609.git.alistair.francis@wdc.com
virtio-fs qualifies as a bootable device minimally under OVMF, but
currently the necessary "bootindex" property is missing. Add the property.
Expose the property only in the PCI device, for now. There is no boot
support for virtiofs on s390x (ccw) for the time being [1] [2], so leave
the CCW device unchanged. Add the property to the base device still,
because adding the alias to the CCW device later will be easier this way
[3].
[1] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01745.html
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01870.html
[3] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01751.html
Example OpenFirmware device path for the "vhost-user-fs-pci" device in the
"bootorder" fw_cfg file:
/pci@i0cf8/pci-bridge@1,6/pci1af4,105a@0/filesystem@0
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ján Tomko <jtomko@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: virtio-fs@redhat.com
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210112131603.12686-1-lersek@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This both allows the wiring to be done as Ben suggested in his original comment in
gpio.c and also enables the OpenPIC object property link to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201229175619.6051-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The OpenPIC device is located within the macio device on real hardware so make it
a child of the macio-newworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-newworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The heathrow PIC is located within the macio device on real hardware so make it
a child of the macio-oldworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-oldworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The PWM module is part of NPCM7XX module. Each NPCM7XX module has two
identical PWM modules. Each module contains 4 PWM entries. Each PWM has
two outputs: frequency and duty_cycle. Both are computed using inputs
from software side.
This module does not model detail pulse signals since it is expensive.
It also does not model interrupts and watchdogs that are dependant on
the detail models. The interfaces for these are left in the module so
that anyone in need for these functionalities can implement on their
own.
The user can read the duty cycle and frequency using qom-get command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-5-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ADC is part of NPCM7XX Module. Its behavior is controled by the
ADC_CON register. It converts one of the eight analog inputs into a
digital input and stores it in the ADC_DATA register when enabled.
Users can alter input value by using qom-set QMP command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-4-wuhaotsh@google.com
[PMM: Added missing hw/adc/trace.h file]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch makes NPCM7XX Timer to use a the timer clock generated by the
CLK module instead of the magic number TIMER_REF_HZ.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows NPCM7XX CLK module to compute clocks that are used by
other NPCM7XX modules.
Add a new struct NPCM7xxClockConverterState which represents a
single converter. Each clock converter in CLK module represents one
converter in NPCM7XX CLK Module(PLL, SEL or Divider). Each converter
takes one or more input clocks and converts them into one output clock.
They form a clock hierarchy in the CLK module and are responsible for
outputing clocks for various other modules in an NPCM7XX SoC.
Each converter has a function pointer called "convert" which represents
the unique logic for that converter.
The clock contains two initialization information: ConverterInitInfo and
ConverterConnectionInfo. They represent the vertices and edges in the
clock diagram respectively.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210108190945.949196-2-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virt machine's 'smp_cpus' and machine->smp.cpus must always have the
same value. And, anywhere we have virt machine state we have machine
state. So let's remove the redundancy. Also, to make it easier to see
that machine->smp is the true source for "smp_cpus" and "max_cpus",
avoid passing them in function parameters, preferring instead to get
them from the state.
No functional change intended.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Ying Fang <fangying1@huawei.com>
Message-id: 20201215174815.51520-1-drjones@redhat.com
[PMM: minor formatting tweak to smp_cpus variable declaration]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is nothing within the translators that ought to be
changing the TranslationBlock data, so make it const.
This does not actually use the read-only copy of the
data structure that exists within the rx region.
Reviewed-by: Joelle van Dyne <j@getutm.app>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The grlib.h header defines a set_pil_in_fn typedef which is never
used; remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212144134.29594-3-peter.maydell@linaro.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently the GRLIB_IRQMP device is used in one place (the leon3 board),
but instead of the device providing inbound gpio lines for the board
to wire up, the board code itself calls qemu_allocate_irqs() with
the handler function being a set_irq function defined in the code
for the device.
Refactor this into the standard setup of a device having input
gpio lines.
This fixes a trivial Coverity memory leak report (the leon3
board code leaks the IRQ array returned from qemu_allocate_irqs()).
Fixes: Coverity CID 1421922
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212144134.29594-2-peter.maydell@linaro.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
First pull request for 2021, which has a bunch of things accumulated
over the holidays. Includes:
* A number of cleanups to sam460ex and ppc440 code from BALATON Zoltan
* Several fixes for builds with --without-default-devices from Greg Kurz
* Fixes for some DRC reset problems from Greg Kurz
* QOM conversion of the PPC 4xx UIC devices from Peter Maydell
* Some other assorted fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=7Eiy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210106' into staging
ppc patch queue 2021-01-06
First pull request for 2021, which has a bunch of things accumulated
over the holidays. Includes:
* A number of cleanups to sam460ex and ppc440 code from BALATON Zoltan
* Several fixes for builds with --without-default-devices from Greg Kurz
* Fixes for some DRC reset problems from Greg Kurz
* QOM conversion of the PPC 4xx UIC devices from Peter Maydell
* Some other assorted fixes and cleanups
# gpg: Signature made Wed 06 Jan 2021 03:33:19 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210106: (22 commits)
ppc440_pcix: Fix up pci config access
ppc440_pcix: Fix register write trace event
ppc440_pcix: Improve comment for IRQ mapping
sam460ex: Remove FDT_PPC dependency from KConfig
ppc4xx: Move common dependency on serial to common option
pnv: Fix reverse dependency on PCI express root ports
ppc: Simplify reverse dependencies of POWERNV and PSERIES on XICS and XIVE
ppc: Fix build with --without-default-devices
spapr: Add drc_ prefix to the DRC realize and unrealize functions
spapr: Use spapr_drc_reset_all() at machine reset
spapr: Introduce spapr_drc_reset_all()
spapr: Fix reset of transient DR connectors
spapr: Call spapr_drc_reset() for all DRCs at CAS
spapr: Fix buffer overflow in spapr_numa_associativity_init()
spapr: Allow memory unplug to always succeed
spapr: Fix DR properties of the root node
spapr/xive: Make spapr_xive_pic_print_info() static
spapr: DRC lookup cannot fail
hw/ppc/ppc440_bamboo: Drop use of ppcuic_init()
hw/ppc/virtex_ml507: Drop use of ppcuic_init()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No need to expose the way DRCs are traversed outside of spapr_drc.c.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-4-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Documentation of object_property_iter_init() clearly stipulates that
"it is forbidden to modify the property list while iterating". But this
is exactly what we do when resetting transient DR connectors during CAS.
The call to spapr_drc_reset() can finalize the hot-unplug sequence of a
PHB or a PCI bridge, both of which will then in turn destroy their PCI
DRCs. This could potentially invalidate the iterator. It is pure luck
that this haven't caused any issues so far.
Change spapr_drc_reset() to return true if it caused a device to be
removed. Restart from scratch in this case. This can potentially
increase the overall DRC reset time, especially with a high maxmem
which generates a lot of LMB DRCs. But this kind of setup is rare,
and so is the use case of rebooting a guest while doing hot-unplug.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-3-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Non-transient DRCs are either in the empty or the ready state,
which means spapr_drc_reset() doesn't change their state. It
is thus not needed to do any checking. Call spapr_drc_reset()
unconditionally and squash spapr_drc_transient() into its
only user, spapr_drc_needed().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-2-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Running a guest with 128 NUMA nodes crashes QEMU:
../../util/error.c:59: error_setv: Assertion `*errp == NULL' failed.
The crash happens when setting the FWNMI migration blocker:
2861 if (spapr_get_cap(spapr, SPAPR_CAP_FWNMI) == SPAPR_CAP_ON) {
2862 /* Create the error string for live migration blocker */
2863 error_setg(&spapr->fwnmi_migration_blocker,
2864 "A machine check is being handled during migration. The handler"
2865 "may run and log hardware error on the destination");
2866 }
Inspection reveals that papr->fwnmi_migration_blocker isn't NULL:
(gdb) p spapr->fwnmi_migration_blocker
$1 = (Error *) 0x8000000004000000
Since this is the only place where papr->fwnmi_migration_blocker is
set, this means someone wrote there in our back. Further analysis
points to spapr_numa_associativity_init(), especially the part
that initializes the associative arrays for NVLink GPUs:
max_nodes_with_gpus = nb_numa_nodes + NVGPU_MAX_NUM;
ie. max_nodes_with_gpus = 128 + 6, but the array isn't sized to
accommodate the 6 extra nodes:
struct SpaprMachineState {
.
.
.
uint32_t numa_assoc_array[MAX_NODES][NUMA_ASSOC_SIZE];
Error *fwnmi_migration_blocker;
};
and the following loops happily overwrite spapr->fwnmi_migration_blocker,
and probably more:
for (i = nb_numa_nodes; i < max_nodes_with_gpus; i++) {
spapr->numa_assoc_array[i][0] = cpu_to_be32(MAX_DISTANCE_REF_POINTS);
for (j = 1; j < MAX_DISTANCE_REF_POINTS; j++) {
uint32_t gpu_assoc = smc->pre_5_1_assoc_refpoints ?
SPAPR_GPU_NUMA_ID : cpu_to_be32(i);
spapr->numa_assoc_array[i][j] = gpu_assoc;
}
spapr->numa_assoc_array[i][MAX_DISTANCE_REF_POINTS] = cpu_to_be32(i);
}
Fix the size of the array. This requires "hw/ppc/spapr.h" to see
NVGPU_MAX_NUM. Including "hw/pci-host/spapr.h" introduces a
circular dependency that breaks the build, so this moves the
definition of NVGPU_MAX_NUM to "hw/ppc/spapr.h" instead.
Reported-by: Min Deng <mdeng@redhat.com>
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1908693
Fixes: dd7e1d7ae4 ("spapr_numa: move NVLink2 associativity handling to spapr_numa.c")
Cc: danielhb413@gmail.com
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160829960428.734871.12634150161215429514.stgit@bahia.lan>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is currently impossible to hot-unplug a memory device between
machine reset and CAS.
(qemu) device_del dimm1
Error: Memory hot unplug not supported for this guest
This limitation was introduced in order to provide an explicit
error path for older guests that didn't support hot-plug event
sources (and thus memory hot-unplug).
The linux kernel has been supporting these since 4.11. All recent
enough guests are thus capable of handling the removal of a memory
device at all time, including during early boot.
Lift the limitation for the latest machine type. This means that
trying to unplug memory from a guest that doesn't support it will
likely just do nothing and the memory will only get removed at
next reboot. Such older guests can still get the existing behavior
by using an older machine type.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160794035064.23292.17560963281911312439.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently the PPC UIC ("Universal Interrupt Controller") is implemented
as a non-QOM device in ppc4xx_devs.c. Convert it to a proper QOM device
in hw/intc.
The ppcuic_init() function is retained for the moment with its current
interface; in subsequent commits this will be tidied up to avoid the
allocation of an irq array.
This conversion adds VMState support.
It leaves the LOG_UIC() macro as-is to maximise the extent to which
this is simply code-movement rather than a rewrite (in new code it
would be better to use tracepoints).
The default property values for dcr-base and use-vectors are set to
match those use by most of our boards with a UIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212001537.24520-3-peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As suggested by Philippe Mathieu-Daudé, rework Loongson's liointc:
1, Move macro definitions to loongson_liointc.h;
2, Remove magic values and use macros instead;
3, Replace dead D() code by trace events.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201221110538.3186646-2-chenhuacai@kernel.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's common to want to print a human-readable indication of a clock's
frequency. Provide a utility function in the clock API to return a
string which is a displayable representation of the frequency,
and use it in qdev-monitor.c.
Before:
(qemu) info qtree
[...]
dev: xilinx,zynq_slcr, id ""
clock-in "ps_clk" freq_hz=3.333333e+07
mmio 00000000f8000000/0000000000001000
After:
dev: xilinx,zynq_slcr, id ""
clock-in "ps_clk" freq_hz=33.3 MHz
mmio 00000000f8000000/0000000000001000
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215150929.30311-5-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove the now-unused clock_get_ns() API and the CLOCK_PERIOD_TO_NS()
macro that only it was using.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215150929.30311-4-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The clock_get_ns() API claims to return the period of a clock in
nanoseconds. Unfortunately since it returns an integer and a
clock's period is represented in units of 2^-32 nanoseconds,
the result is often an approximation, and calculating a clock
expiry deadline by multiplying clock_get_ns() by a number-of-ticks
is unacceptably inaccurate.
Introduce a new API clock_ticks_to_ns() which returns the number
of nanoseconds it takes the clock to make a given number of ticks.
This function can do the complete calculation internally and
will thus give a more accurate result.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215150929.30311-2-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove legacy vt82c686b_pm_init() function and also rename
VT82C686B_PM type name to match other device names.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a70982b32f11222d335385b90749abb6cf2e2cce.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These are legacy init functions that are just equivalent to directly
calling pci_create_simple so do that instead. Also rename objects to
lower case via-ac97 and via-mc97 matching naming of other devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1c4373c8aeb6c4fb2a8df2c864b0e91a977a3d7b.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The function will be moved to common QOM code, as it is not
specific to TYPE_DEVICE anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the variable declaration close to the macro that uses it.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-29-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Returning ObjectProperty* will be useful for new property
registration code that will add additional callbacks
to ObjectProperty after registering it.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-25-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make it easier to remove the Property.name field in the
future.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-22-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Replace `Property *prop` parameter with `char *name`, to reduce
dependency of getter and setter functions on the Property struct
(which will be changed in following patches).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201211220529.2290218-19-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of duplicating the code that sets name, info, offset,
and does type checking, make DEFINE_PROP accept a variable number
of arguments and reuse it in all DEFINE_PROP_* macros.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-17-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of using string compares to determine if a RISC-V machine is
using 32-bit or 64-bit CPUs we can use the initalised CPUs. This avoids
us having to maintain a list of CPU names to compare against.
This commit also fixes the name of the function to match the
riscv_cpu_is_32bit() function.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 8ab7614e5df93ab5267788b73dcd75f9f5615e82.1608142916.git.alistair.francis@wdc.com
QEMU requires Clang or GCC, that define and support __GNUC__ extensions
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <20201210134752.780923-11-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Generalize the qdev_hotplug variable to the different phases of
machine initialization. We would like to allow different
monitor commands depending on the phase.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qdev_machine_creation_done is only setting a flag now. Extend it to
move more code out of vl.c. Leave only consistency checks and gdbserver
processing in qemu_machine_creation_done.
gdbserver_start can be moved after qdev_machine_creation_done because
it only does listen on the socket and creates some internal data
structures; it does not send any data (e.g. guest state) over the socket.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
-----BEGIN PGP SIGNATURE-----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=lHZA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20201215' into staging
target-arm queue:
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
# gpg: Signature made Tue 15 Dec 2020 13:59:46 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20201215:
hw/block/m25p80: Fix Numonyx fast read dummy cycle count
hw/block/m25p80: Check SPI mode before running some Numonyx commands
hw/block/m25p80: Fix when VCFG XIP bit is set for Numonyx
hw/block/m25p80: Make Numonyx config field names more accurate
hw/misc/zynq_slcr: Avoid #DIV/0! error
arm: xlnx-versal: Connect usb to virt-versal
usb: xlnx-usb-subsystem: Add xilinx usb subsystem
usb: Add DWC3 model
usb: Add versal-usb2-ctrl-regs module
elf_ops.h: Be more verbose with ROM blob names
elf_ops.h: Don't truncate name of the ROM blobs we create
hw/core/loader.c: Improve reporting of ROM overlap errors
hw/core/loader.c: Track last-seen ROM in rom_check_and_register_reset()
target/nios2: Use deposit32() to update ipending register
target/nios2: Move nios2_check_interrupts() into target/nios2
target/nios2: Move IIC code into CPU object proper
target/openrisc: Move pic_cpu code into CPU object proper
hw/openrisc/openrisc_sim: Abstract out "get IRQ x of CPU y"
hw/openrisc/openrisc_sim: Use IRQ splitter when connecting IRQ to multiple CPUs
gdbstub: Correct misparsing of vCont C/S requests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> #s390 parts
Message-Id: <20201211220529.2290218-13-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> #s390 parts
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-10-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-8-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move everything related to Property and PropertyInfo to
qdev-properties.[ch] to make it easier to refactor that code.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
There's no reason to keep the property list separate from the CPU
class code. Move the variable to hw/core/cpu.c and make it
static.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Connect VersalUsb2 subsystem to xlnx-versal SOC, its placed
in iou of lpd domain and configure it as dual port host controller.
Add the respective guest dts nodes for "xlnx-versal-virt" machine.
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1607023357-5096-5-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This model is a top level integration wrapper for hcd-dwc3 and
versal-usb2-ctrl-regs modules, this is used by xilinx versal soc's and
future xilinx usb subsystems would also be part of it.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1607023357-5096-4-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds skeleton model of dwc3 usb controller attached to
xhci-sysbus device. It defines global register space of DWC3 controller,
global registers control the AXI/AHB interfaces properties, external FIFO
support and event count support. All of which are unimplemented at
present,we are only supporting core reset and read of ID register.
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1607023357-5096-3-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This module emulates control registers of versal usb2 controller, this is added
just to make guest happy. In general this module would control the phy-reset
signal from usb controller, data coherency of the transactions, signals
the host system errors received from controller.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1607023357-5096-2-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of making the ROM blob name something like:
phdr #0: /home/petmay01/linaro/qemu-misc-tests/ldmia-fault.axf
make it a little more self-explanatory for people who don't know
ELF format details:
/home/petmay01/linaro/qemu-misc-tests/ldmia-fault.axf ELF program header segment 0
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201129203923.10622-5-peter.maydell@linaro.org
Currently the load_elf code assembles the ROM blob name into a
local 128 byte fixed-size array. Use g_strdup_printf() instead so
that we don't truncate the pathname if it happens to be long.
(This matters mostly for monitor 'info roms' output and for the
error messages if ROM blobs overlap.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201129203923.10622-4-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=aOV/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging
Pull request trivial-patches 20201214
# gpg: Signature made Mon 14 Dec 2020 15:52:07 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.0-pull-request:
configure / meson: Move check for linux/btrfs.h to meson.build
configure / meson: Move check for sys/kcov.h to meson.build
configure / meson: Move check for sys/signal.h to meson.build
configure / meson: Move check for drm.h to meson.build
configure / meson: Move check for pty.h to meson.build
configure: Remove the obsolete check for ifaddrs.h
blockdev: Fix a memleak in drive_backup_prepare()
block/file-posix: fix a possible undefined behavior
elf2dmp/pdb: Plug memleak in pdb_init_from_file
elf2dmp/qemu_elf: Plug memleak in QEMU_Elf_init
configure: Test if $make actually exists
ads7846: moves from the hw/display folder to the hw/input folder.
CODING_STYLE.rst: Be less strict about 80 character limit
fsdev: open brace '{' following struct go on the same line
hw/pci-host/pam: Replace magic number by PAM_REGIONS_COUNT definition
hw/xen: Don't use '#' flag of printf format
MAINTAINERS: update my email address
qemu-options.hx: Fix minor issues in icount documentation
target/i386: tracing: format length values as hex
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows to drop a user of qdev_get_machine().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201209170052.1431440-4-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All users are passing &error_abort already. Document the fact
that spapr_drc_attach() should only be passed a free DRC, which
is supposedly the case if appropriate checking is done earlier.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201201113728.885700-5-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Read documentation in "qapi/error.h" and changelog of commit
e3fe3988d7 ("error: Document Error API usage rules") for
rationale.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120234208.683521-7-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Pre-plug of a memory device, be it an NVDIMM or a PC-DIMM, ensures
that the memory slot is available and that addresses don't overlap
with existing memory regions. The corresponding DRCs in the LMB
and PMEM namespaces are thus necessarily attachable at plug time.
Pass &error_abort to spapr_drc_attach() in spapr_add_lmbs() and
spapr_add_nvdimm(). This allows to greatly simplify error handling
on the plug path.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120234208.683521-3-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Never used from the start.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120174646.619395-6-groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Address translation is an architectural thing (not hardware
related). Move the helpers from hw/ to target/.
As physical address and KVM are specific to system mode
emulation, restrict this file to softmmu, so it doesn't
get compiled for user-mode emulation.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201206233949.3783184-2-f4bug@amsat.org>
While this change helps triskaidekaphobic developers, it
is a good practice to avoid magic values and using constant
definitions instead.
Introduce the PAM_REGIONS_COUNT and use it. No logical change.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Julia Suvorova <jusual@redhat.com>
Message-Id: <20201202132038.1276404-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move more of them into MachineState, in preparation for moving initialization
of the machine out of vl.c.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some very simple initialization routines can be nested in existing
subsystem-level functions, do that to simplify qemu_init.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Once smp_parse is done, the validation operates on the MachineState.
There is no reason for that code to be in vl.c.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-6-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename 'slave stream'
as 'sink stream'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200910070131.435543-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To make the next commit easier to review, clean this code first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-3-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename max_slaves
as max_peripherals.
Patch generated using:
$ sed -i s/slave/peripheral/ \
hw/ssi/aspeed_smc.c include/hw/ssi/aspeed_smc.h
One line in aspeed_smc_read() has been manually tweaked
to pass checkpatch.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201012124955.3409127-2-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
pci_dma_rw() returns a MemTxResult type.
Do not discard it, return it to the caller.
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201023151923.3243652-11-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
pci_dma_rw() returns a MemTxResult type.
Do not discard it, return it to the caller.
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201023151923.3243652-10-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
dma_memory_rw() returns a MemTxResult type.
Do not discard it, return it to the caller.
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201023151923.3243652-9-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
contrib/plugins/hotblocks.c
contrib/plugins/hotpages.c
contrib/plugins/howvec.c
contrib/plugins/lockstep.c
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/fp/platform.h
tests/migration/s390x/a-b-bios.c
tests/plugin/bb.c
tests/plugin/empty.c
tests/plugin/insn.c
tests/plugin/mem.c
tests/test-rcu-simpleq.c
tests/test-rcu-slist.c
tests/test-rcu-tailq.c
tests/uefi-test-tools/UefiTestToolsPkg/BiosTablesTest/BiosTablesTest.c
contrib/plugins/, tests/plugin/, and tests/test-rcu-slist.c appear not
to include osdep.h intentionally. The remaining reverts are the same
as in commit bbfff19688.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201113061216.2483385-1-armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAl/SDVIACgkQUaNDx8/7
7KFF3BAAvYPgi/XJN0caP0qbxZy7GvBA1nmINQq910d1ARz04Vin8K6oj9x02taq
1MMhk9KryNRF1VuT98eya8u9htsg1OxrosqSAwjrtI72oSRWLGSl1Ww0sKIPcBET
OUq8pfAv+gW5lVWRkpnEA4Ly33PMTp5zfT3sy0riuSf+Z7Mg/8Lk28tNSOYu6hBl
LUZddcweMshishrJ46F1SSwWFfdZ2+5Y1eLSDRGwn8Ba5xy6SI3UDQVFze1vFmo3
h1Sd9s2tVJtJn4It2op41XKQX99uoGUy98CYVrbAd/1euZIm/6c4ju9upZiFUU/p
wm8I1njd5ybdPzRmJkJ8zQxsblgvw/Ua0YLmX/4aFsPUlKPyomOr++YMXcyrThEY
cxezJsSmj5f/oVaGRULbRVR8hhaM18RLBgwQAbfNSOTylmFa+URT6FLR4mnysfhz
zv76xt6S8BIS8CAgxqB13tj4tQPXUansQsuVTWwRwE8mHd5Vkhau2oOQR5n9cV+n
FNjvmqUN7ICtekmwMmBdNOI4yiGBY1ckcj/UoCzkuAYK444kzTqFfB4CZABNhs5f
/fjAsWAvYtqsLFUWCUnpHkxyq/8N0hpSZc0DI3FDPsup4/NlRG17p+DcrNqimwIE
SZ1I28YYdmoh1igMQK46x7UvvnceCCXkHAnR+nGix8jOpSCWLKs=
=abAb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20201210' into staging
Aspeed patches :
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
# gpg: Signature made Thu 10 Dec 2020 11:58:10 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20201210:
aspeed: g220a-bmc: Add an FRU
aspeed/smc: Add support for address lane disablement
ast2600: SRAM is 89KB
aspeed: Add support for the g220a-bmc board
hw/misc: add an EMC141{3,4} device model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RAS feature has a block of memory-mapped registers at offset
0x5000 within the PPB. For a "minimal RAS" implementation we provide
no error records and so the only registers that exist in the block
are ERRIIDR and ERRDEVID.
The "RAZ/WI for privileged, BusFault for nonprivileged" behaviour
of the "nvic-default" region is actually valid for minimal-RAS,
so the main benefit of providing an explicit implementation of
the register block is more accurate LOG_UNIMP messages, and a
framework for where we could add a real RAS implementation later
if necessary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-27-peter.maydell@linaro.org
For M-profile CPUs, the range from 0xe0000000 to 0xe00fffff is the
Private Peripheral Bus range, which includes all of the memory mapped
devices and registers that are part of the CPU itself, including the
NVIC, systick timer, and debug and trace components like the Data
Watchpoint and Trace unit (DWT). Within this large region, the range
0xe000e000 to 0xe000efff is the System Control Space (NVIC, system
registers, systick) and 0xe002e000 to 0exe002efff is its Non-secure
alias.
The architecture is clear that within the SCS unimplemented registers
should be RES0 for privileged accesses and generate BusFault for
unprivileged accesses, and we currently implement this.
It is less clear about how to handle accesses to unimplemented
regions of the wider PPB. Unprivileged accesses should definitely
cause BusFaults (R_DQQS), but the behaviour of privileged accesses is
not given as a general rule. However, the register definitions of
individual registers for components like the DWT all state that they
are RES0 if the relevant component is not implemented, so the
simplest way to provide that is to provide RAZ/WI for the whole range
for privileged accesses. (The v7M Arm ARM does say that reserved
registers should be UNK/SBZP.)
Expand the container MemoryRegion that the NVIC exposes so that
it covers the whole PPB space. This means:
* moving the address that the ARMV7M device maps it to down by
0xe000 bytes
* moving the off and the offsets within the container of all the
subregions forward by 0xe000 bytes
* adding a new default MemoryRegion that covers the whole container
at a lower priority than anything else and which provides the
RAZWI/BusFault behaviour
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-2-peter.maydell@linaro.org
Connect CAN0 and CAN1 on the ZynqMP.
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-3-git-send-email-fnu.vikram@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xilinx ZynqMP CAN controller is developed based on SocketCAN, QEMU CAN bus
implementation. Bus connection and socketCAN connection for each CAN module
can be set through command lines.
Example for using single CAN:
-object can-bus,id=canbus0 \
-machine xlnx-zcu102.canbus0=canbus0 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0
Example for connecting both CAN to same virtual CAN on host machine:
-object can-bus,id=canbus0 -object can-bus,id=canbus1 \
-machine xlnx-zcu102.canbus0=canbus0 \
-machine xlnx-zcu102.canbus1=canbus1 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0 \
-object can-host-socketcan,id=socketcan1,if=vcan0,canbus=canbus1
To create virtual CAN on the host machine, please check the QEMU CAN docs:
https://github.com/qemu/qemu/blob/master/docs/can.txt
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-2-git-send-email-fnu.vikram@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Largely inspired by the TMP421 temperature sensor, here is a model for
the EMC1413/EMC1414 temperature sensors.
Specs can be found here :
http://ww1.microchip.com/downloads/en/DeviceDoc/20005274A.pdf
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201122105134.671-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Create second ioapic, route virtio-mmio IRQs to it,
allow more virtio-mmio devices (24 instead of 8).
Needs ACPI, enabled by default, can be turned off
using -machine ioapic2=off
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-8-kraxel@redhat.com
Allows to move them in case we have enough
irq lines available.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-6-kraxel@redhat.com
This will allow to increase the number of transports in
case we have enough irq lines available for them all.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-5-kraxel@redhat.com
Add ioapic_init_secondary to initialize it, wire up
in gsi handling and acpi apic table creation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-4-kraxel@redhat.com
if firmware and QEMU negotiated CPU hotunplug support, generate
_EJ0 method so that it will mark CPU for removal by firmware and
pass control to it by triggering SMI.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Adds bit #4 to status/control field of CPU hotplug MMIO interface.
New bit will be used OSPM to mark CPUs as pending for removal by firmware,
when it calls _EJ0 method on CPU device node. Later on, when firmware
sees this bit set, it will perform CPU eject which will clear bit #4
as well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At Hewlett Packard Inc. we have a need for increased fw size to enable testing of our custom fw.
Rebase v6 patch to d73c46e4
Signed-off-by: Erich McMillan <erich.mcmillan@hp.com>
Message-Id: <20201208155338.14-1-erich.mcmillan@hp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 6.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201109173928.1001764-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only three uses remained, and we can remove them on that case.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-28-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-25-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use pasive.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-17-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We didn't use at all the -1 value, and we don't really care. It was
only used for the cases when this is not the device that we are
searching for. And in that case we should not hide the device.
Once there, simplify virtio-Snet_primary_should_be_hidden.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-16-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was only used once. And we have there opts->id, so no need for it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-13-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate it, and we only use it once anyways.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-12-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was really only used once, in failover_add_primary(). Just search
for it on global opts when it is needed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-11-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use passive naming variables.
And once there, be able to search for them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-9-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Just remove the struct member.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-5-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resources of pxbs are obtained by crs_build and the resources
used by pxbs would be moved from the resources defined for host-bridge.
The resources for pxb are composed of following two parts:
1. The bar space of the pci-bridge/pcie-root-port behined it
2. The config space of devices behind it.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-6-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract crs build form acpi_build.c, the function could also be used
to build the crs for pxbs for arm. The resources are composed by two parts:
1. The bar space of pci-bridge/pcie-root-ports
2. The resources needed by devices behind PXBs.
The base and limit of memory/io are obtained from the config via two APIs:
pci_bridge_get_base and pci_bridge_get_limit
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-5-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add bus property to virt machine for primary PCI root bus and use it to add
extra pci roots behind it.
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Message-Id: <20201119014841.7298-4-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract extra pci roots addition from pc machine, which could be used by
other machines.
In order to make uefi get the extra roots, it is necessary to write extra
roots into fw_cfg. And only if the uefi knows there are extra roots,
the config spaces of devices behind the root could be obtained.
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Message-Id: <20201119014841.7298-3-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By default dirty pages tracking is enabled during iterative phase
(pre-copy phase).
Added per device opt-out option 'x-pre-copy-dirty-page-tracking' to
disable dirty pages tracking during iterative phase. If the option
'x-pre-copy-dirty-page-tracking=off' is set for any VFIO device, dirty
pages tracking during iterative phase will be disabled.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Support for migration of vfio devices is still in flux. Developers
are attempting to add support for new devices and new architectures,
but none are yet readily available for validation. We have concerns
whether we're transferring device resources at the right point in the
migration, whether we're guaranteeing that updates during pre-copy are
migrated, and whether we can provide bit-stream compatibility should
any of this change. Even the question of whether devices should
participate in dirty page tracking during pre-copy seems contentious.
In short, migration support has not had enough soak time and it feels
premature to mark it as supported.
Create an experimental option such that we can continue to develop.
[Retaining previous acks/reviews for a previously identical code
change with different specifics in the commit log.]
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The zPCI group and function structures are big endian. However, we do
not consistently store them as big endian locally, and are missing some
conversions.
Let's just store the structures as host endian instead and convert to
big endian when actually handling the instructions retrieving the data.
Also fix the layout of ClpReqQueryPciGrp: g is actually only 8 bit. This
also fixes accesses on little endian hosts, and makes accesses on big
endian hosts consistent.
Fixes: 28dc86a072 ("s390x/pci: use a PCI Group structure")
Fixes: 9670ee7527 ("s390x/pci: use a PCI Function structure")
Fixes: 1e7552ff5c ("s390x/pci: get zPCI function info from host")
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201118104202.1301363-1-cohuck@redhat.com>
-----BEGIN PGP SIGNATURE-----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=GI5d
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-11-15' into staging
Fix Lesser GPL license versions (should be "2.1" and not "2")
# gpg: Signature made Sun 15 Nov 2020 16:20:10 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-11-15: (26 commits)
nomaintainer: Fix Lesser GPL version number
test: Fix LGPL information in the file headers
tests/acceptance: Fix LGPL information in the file headers
tests/migration: Fix LGPL information in the file headers
sparc tcg cpus: Fix Lesser GPL version number
e1000e: Fix Lesser GPL version number
x86 hvf cpus: Fix Lesser GPL version number
nvdimm: Fix Lesser GPL version number
w32: Fix Lesser GPL version number
tpm: Fix Lesser GPL version number
overall/alpha tcg cpus|hppa: Fix Lesser GPL version number
overall usermode...: Fix Lesser GPL version number
migration: Fix Lesser GPL version number
parallel nor flash: Fix Lesser GPL version number
arm tcg cpus: Fix Lesser GPL version number
x86 tcg cpus: Fix Lesser GPL version number
linux user: Fix Lesser GPL version number
usb: Fix Lesser GPL version number
tricore tcg cpus: Fix Lesser GPL version number
xtensa tcg cpus: Fix Lesser GPL version number
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Chardev is already a typedef'ed struct.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201110192316.26397-5-alex.bennee@linaro.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201016145346.27167-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201016144243.26817-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
If an interrupt occurs between when we claim and complete an interrupt
we currently drop the interrupt in ibex_plic_irqs_set_pending(). This
somewhat matches hardware that also ignore the interrupt between the
claim and complete process.
In the case of hardware though the physical interrupt line will still
be asserted after we have completed the interrupt. This means we will
still act on the interrupt after the complete process. In QEMU we don't
and instead we drop the interrupt as it is never recorded.
This patch changed the behaviour of the Ibex PLIC so that we save all
interrupts that occur while we are between claiming and completing an
interrupt so that we can act on them after the completition process.
This fixes interrupts being dropped when running Tock on OpenTitain in
QEMU.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: e7bcf98c6925b1e6e7828e7c3f85293a09a65b12.1605136387.git.alistair.francis@wdc.com
The system configuration controller (SYSCFG) doesn't have
any output IRQ (and the INTC input #71 belongs to the UART6).
Remove the invalid code.
Fixes: db635521a0 ("stm32f205: Add the stm32f205 SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Lots of fixes all over the place.
virtio-mem and virtio-iommu patches are kind of fixes but
it seems better to just make them behave sanely than
try to educate users about the limitations ...
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl+i9YMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpySQH/Ru/sxB9PncR1HsqSf0HC0tt/EMKgyZTXEwQ
FITcjkCvBDS98a1VUvvZbjzTEDEZNnoUv94MjdLeBoptJ7GtK6nPoI6Ke0p1Zqbe
mlY2BCb0FpN8FE+mthjAI03mhw6o8Qo/OPtyISQzUxCVVqUHL5TRAVAQdeidoK8n
RBQ4WogwM/h7wI0d9GGgSxAON8IRQnBYImtzJieBb6zeScwKVFTWI1tqBdOyFN0/
AhzQiNZuhZ7a1XGJIsxmWB1NK2kcXNJuOF0ANh4coIHR0JzmH3xRy+Jnf5e3dYsw
LI23DUZPSTJJXAwKPucyTG7RTX8F55N9DVHC9KDRD6Ntq1oreJ4=
=pcbN
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,vhost,virtio: fixes
Lots of fixes all over the place.
virtio-mem and virtio-iommu patches are kind of fixes but
it seems better to just make them behave sanely than
try to educate users about the limitations ...
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 04 Nov 2020 18:40:03 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
contrib/vhost-user-blk: fix get_config() information leak
block/export: fix vhost-user-blk get_config() information leak
block/export: make vhost-user-blk config space little-endian
configure: introduce --enable-vhost-user-blk-server
libvhost-user: follow QEMU comment style
vhost-blk: set features before setting inflight feature
Revert "vhost-blk: set features before setting inflight feature"
net: Add vhost-vdpa in show_netdevs()
vhost-vdpa: Add qemu_close in vhost_vdpa_cleanup
vfio: Don't issue full 2^64 unmap
virtio-iommu: Set supported page size mask
vfio: Set IOMMU page size as per host supported page size
memory: Add interface to set iommu page size mask
virtio-iommu: Add notify_flag_changed() memory region callback
virtio-iommu: Add replay() memory region callback
virtio-iommu: Call memory notifiers in attach/detach
virtio-iommu: Add memory notifiers for map/unmap
virtio-iommu: Store memory region in endpoint struct
virtio-iommu: Fix virtio_iommu_mr()
hw/smbios: Fix leaked fd in save_opt_one() error path
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s390-pci-vfio.c calls into the vfio code, so we need it to be
built conditionally on vfio (which implies CONFIG_LINUX).
Fixes: cd7498d07f ("s390x/pci: Add routine to get the vfio dma available count")
Reported-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20201103123237.718242-1-cohuck@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20201103123617.28256-1-jin.yu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit adb29c0273.
The commit broke -device vhost-user-blk-pci because the
vhost_dev_prepare_inflight() function it introduced segfaults in
vhost_dev_set_features() when attempting to access struct vhost_dev's
vdev pointer before it has been assigned.
To reproduce the segfault simply launch a vhost-user-blk device with the
contrib vhost-user-blk device backend:
$ build/contrib/vhost-user-blk/vhost-user-blk -s /tmp/vhost-user-blk.sock -r -b /var/tmp/foo.img
$ build/qemu-system-x86_64 \
-device vhost-user-blk-pci,id=drv0,chardev=char1,addr=4.0 \
-object memory-backend-memfd,id=mem,size=1G,share=on \
-M memory-backend=mem,accel=kvm \
-chardev socket,id=char1,path=/tmp/vhost-user-blk.sock
Segmentation fault (core dumped)
Cc: Jin Yu <jin.yu@intel.com>
Cc: Raphael Norwitz <raphael.norwitz@nutanix.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20201102165709.232180-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201023122633.19466-1-chetan4windows@gmail.com>
[PMD: Added hw/mips/ prefix in subject]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201016143509.26692-1-chetan4windows@gmail.com>
[PMD: Split hw/ vs target/]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The latest SD card image [1] released by Microchip ships a Linux
kernel with built-in PolarFire SoC I2C driver support. The device
tree file includes the description for the I2C1 node hence kernel
tries to probe the I2C1 device during boot.
It is enough to create an unimplemented device for I2C1 to allow
the kernel to continue booting to the shell.
[1] ftp://ftpsoc.microsemi.com/outgoing/core-image-minimal-dev-icicle-kit-es-sd-20201009141623.rootfs.wic.gz
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-11-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When system memory is larger than 1 GiB (high memory), PolarFire SoC
maps it at address 0x10_0000_0000. Address 0xC000_0000 and above is
aliased to the same 1 GiB low memory with different cache attributes.
At present QEMU maps the system memory contiguously from 0x8000_0000.
This corrects the wrong QEMU logic. Note address 0x14_0000_0000 is
the alias to the high memory, and even physical memory is only 1 GiB,
the HSS codes still tries to probe the high memory alias address.
It seems there is no issue on the real hardware, so we will have to
take that into the consideration in our emulation. Due to this, we
we increase the default system memory size to 1537 MiB (the minimum
required high memory size by HSS) so that user gets notified an error
when less than 1537 MiB is specified.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201101170538.3732-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Somehow HSS needs to access address 0 [1] for the DDR calibration data
which is in the chipset's reserved memory. Let's map it.
[1] See the config_copy() calls in various places in ddr_setup() in
the HSS source codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-9-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously SYSREG was created as an unimplemented device. Now that
we have a simple SYSREG module, connect it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-8-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This creates a minimum model for Microchip PolarFire SoC SYSREG
module. It only implements the ENVM_CR register to tell guest
software that eNVM is running at the configured divider rate.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-7-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously IOSCB_CFG was created as an unimplemented device. With
the new IOSCB model, its memory range is already covered by the
IOSCB hence remove the previous unimplemented device creation in
the SoC codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-6-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This creates a model for PolarFire SoC IOSCB [1] module. It actually
contains lots of sub-modules like various PLLs to control different
peripherals. Only the mininum capabilities are emulated to make the
HSS DDR memory initialization codes happy. Lots of sub-modules are
created as an unimplemented devices.
[1] PF_SoC_RegMap_V1_1/MPFS250T/mpfs250t_ioscb_memmap_dri.htm in
https://www.microsemi.com/document-portal/doc_download/1244581-polarfire-soc-register-map
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-5-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect DDR SGMII PHY module and CFG module to the PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-4-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The PolarFire SoC DDR Memory Controller mainly includes 2 modules,
called SGMII PHY module and the CFG module, as documented in the
chipset datasheet.
This creates a single file that groups these 2 modules, providing
the minimum functionalities that make the HSS DDR initialization
codes happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-3-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add sifive_plic vmstate for supporting sifive_plic migration.
Current vmstate framework only supports one structure parameter
as num field to describe variable length arrays, so introduce
num_enables.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Yipeng Yin <yinyipeng1@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201026115530.304-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
libFuzzer triggered the following assertion:
cat << EOF | qemu-system-i386 -M pc-q35-5.0 \
-nographic -monitor none -serial none \
-qtest stdio -d guest_errors -trace pci\*
outl 0xcf8 0x8400f841
outl 0xcfc 0xebed205d
outl 0x5d02 0xedf82049
EOF
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
hw/pci/pci.c:268: int pci_bus_get_irq_level(PCIBus *, int): Assertion `irq_num < bus->nirq' failed.
This is because ich9_lpc_sci_irq() returns -1 for reserved
(illegal) values, but ich9_lpc_pmbase_sci_update() considers
it valid and store it in a 8-bit unsigned type. Then the 255
value is used as GSI IRQ, resulting in a PIRQ value of 247,
more than ICH9_LPC_NB_PIRQS (8).
Fix by simply ignoring the invalid access (and reporting it):
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
ICH9 LPC: SCI IRQ SEL #3 is reserved
pci_cfg_read mch 00:0 @0x0 -> 0x8086
pci_cfg_read mch 00:0 @0x0 -> 0x29c08086
...
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: 8f242cb724 ("ich9: implement SCI_IRQ_SEL register")
BugLink: https://bugs.launchpad.net/qemu/+bug/1878642
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200717151705.18611-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a callback that can be used to express additional alignment
requirements (exceeding the ones from the memory region).
Will be used by virtio-mem to express special alignment requirements due
to manually configured, big block sizes (e.g., 1GB with an ordinary
memory-backend-ram). This avoids failing later when realizing, because
auto-detection wasn't able to assign a properly aligned address.
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201008083029.9504-6-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----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=s4KC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/nvme/tags/pull-nvme-20201102' into staging
nvme pull 2 Nov 2020
# gpg: Signature made Mon 02 Nov 2020 15:20:30 GMT
# gpg: using RSA key DBC11D2D373B4A3755F502EC625156610A4F6CC0
# gpg: Good signature from "Keith Busch <kbusch@kernel.org>" [unknown]
# gpg: aka "Keith Busch <keith.busch@gmail.com>" [unknown]
# gpg: aka "Keith Busch <keith.busch@intel.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DBC1 1D2D 373B 4A37 55F5 02EC 6251 5661 0A4F 6CC0
* remotes/nvme/tags/pull-nvme-20201102: (30 commits)
hw/block/nvme: fix queue identifer validation
hw/block/nvme: fix create IO SQ/CQ status codes
hw/block/nvme: fix prp mapping status codes
hw/block/nvme: report actual LBA data shift in LBAF
hw/block/nvme: add trace event for requests with non-zero status code
hw/block/nvme: add nsid to get/setfeat trace events
hw/block/nvme: reject io commands if only admin command set selected
hw/block/nvme: support for admin-only command set
hw/block/nvme: validate command set selected
hw/block/nvme: support per-namespace smart log
hw/block/nvme: fix log page offset check
hw/block/nvme: remove pointless rw indirection
hw/block/nvme: update nsid when registered
hw/block/nvme: change controller pci id
pci: allocate pci id for nvme
hw/block/nvme: support multiple namespaces
hw/block/nvme: refactor identify active namespace id list
hw/block/nvme: add support for sgl bit bucket descriptor
hw/block/nvme: add support for scatter gather lists
hw/block/nvme: harden cmb access
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In gicv3_init_cpuif() we copy the ARMCPU gicv3_maintenance_interrupt
into the GICv3CPUState struct's maintenance_irq field. This will
only work if the board happens to have already wired up the CPU
maintenance IRQ before the GIC was realized. Unfortunately this is
not the case for the 'virt' board, and so the value that gets copied
is NULL (since a qemu_irq is really a pointer to an IRQState struct
under the hood). The effect is that the CPU interface code never
actually raises the maintenance interrupt line.
Instead, since the GICv3CPUState has a pointer to the CPUState, make
the dereference at the point where we want to raise the interrupt, to
avoid an implicit requirement on board code to wire things up in a
particular order.
Reported-by: Jose Martins <josemartins90@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201009153904.28529-1-peter.maydell@linaro.org
Reviewed-by: Luc Michel <luc@lmichel.fr>
We use the capability chains of the VFIO_DEVICE_GET_INFO ioctl to retrieve
the CLP information that the kernel exports.
To be compatible with previous kernel versions we fall back on previous
predefined values, same as the emulation values, when the ioctl is found
to not support capability chains. If individual CLP capabilities are not
found, we fall back on default values for only those capabilities missing
from the chain.
This patch is based on work previously done by Pierre Morel.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: non-Linux build fixes]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now that VFIO_DEVICE_GET_INFO supports capability chains, add a helper
function to find specific capabilities in the chain.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use a ClpRspQueryPci structure to hold the information related to a
zPCI Function.
This allows us to be ready to support different zPCI functions and to
retrieve the zPCI function information from the host.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use a S390PCIGroup structure to hold the information related to a
zPCI Function group.
This allows us to be ready to support multiple groups and to retrieve
the group information from the host.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
To have a clean separation between s390-pci-bus.h and s390-pci-inst.h
headers we export the PCI CLP instructions in a dedicated header.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When an s390 guest is using lazy unmapping, it can result in a very
large number of oustanding DMA requests, far beyond the default
limit configured for vfio. Let's track DMA usage similar to vfio
in the host, and trigger the guest to flush their DMA mappings
before vfio runs out.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: non-Linux build fixes]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Create new files for separating out vfio-specific work for s390
pci. Add the first such routine, which issues VFIO_IOMMU_GET_INFO
ioctl to collect the current dma available count.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: Fix non-Linux build with CONFIG_LINUX]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The underlying host may be limiting the number of outstanding DMA
requests for type 1 IOMMU. Add helper functions to check for the
DMA available capability and retrieve the current number of DMA
mappings allowed.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: vfio_get_info_dma_avail moved inside CONFIG_LINUX]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Seems a more appropriate location for them.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added amount of bytes transferred to the VM at destination by all VFIO
devices
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added helper functions to get IOMMU info capability chain.
Added function to get migration capability information from that
capability chain for IOMMU container.
Similar change was proposed earlier:
https://lists.gnu.org/archive/html/qemu-devel/2018-05/msg03759.html
Disable migration for devices if IOMMU module doesn't support migration
capability.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added .save_live_pending, .save_live_iterate and .save_live_complete_precopy
functions. These functions handles pre-copy and stop-and-copy phase.
In _SAVING|_RUNNING device state or pre-copy phase:
- read pending_bytes. If pending_bytes > 0, go through below steps.
- read data_offset - indicates kernel driver to write data to staging
buffer.
- read data_size - amount of data in bytes written by vendor driver in
migration region.
- read data_size bytes of data from data_offset in the migration region.
- Write data packet to file stream as below:
{VFIO_MIG_FLAG_DEV_DATA_STATE, data_size, actual data,
VFIO_MIG_FLAG_END_OF_STATE }
In _SAVING device state or stop-and-copy phase
a. read config space of device and save to migration file stream. This
doesn't need to be from vendor driver. Any other special config state
from driver can be saved as data in following iteration.
b. read pending_bytes. If pending_bytes > 0, go through below steps.
c. read data_offset - indicates kernel driver to write data to staging
buffer.
d. read data_size - amount of data in bytes written by vendor driver in
migration region.
e. read data_size bytes of data from data_offset in the migration region.
f. Write data packet as below:
{VFIO_MIG_FLAG_DEV_DATA_STATE, data_size, actual data}
g. iterate through steps b to f while (pending_bytes > 0)
h. Write {VFIO_MIG_FLAG_END_OF_STATE}
When data region is mapped, its user's responsibility to read data from
data_offset of data_size before moving to next steps.
Added fix suggested by Artem Polyakov to reset pending_bytes in
vfio_save_iterate().
Added fix suggested by Zhi Wang to add 0 as data size in migration stream and
add END_OF_STATE delimiter to indicate phase complete.
Suggested-by: Artem Polyakov <artemp@nvidia.com>
Suggested-by: Zhi Wang <zhi.wang.linux@gmail.com>
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added migration state change notifier to get notification on migration state
change. These states are translated to VFIO device state and conveyed to
vendor driver.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VM state change handler is called on change in VM's state. Based on
VM state, VFIO device state should be changed.
Added read/write helper functions for migration region.
Added function to set device_state.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: lx -> HWADDR_PRIx, remove redundant parens]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Whether the VFIO device supports migration or not is decided based of
migration region query. If migration region query is successful and migration
region initialization is successful then migration is supported else
migration is blocked.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added functions to save and restore PCI device specific data,
specifically config space of PCI device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This function will be used for migration region.
Migration region is mmaped when migration starts and will be unmapped when
migration is complete.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Just a bunch of bugfixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl+cCq8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpKWkH/0qq+u2z/q0KYzmodcdW2eFNsvKF2e+Dz3Af
zZGMREH93DsKAQ2k3t84sz2RAaAP45cCqrq+v8kSzmpaC7GqKYA/VceeLwy8e6Eu
YKvu5QixrOVTpNg2QV/w44ywgtA4NbWy5Fr9S4qhzPyyD/gtE609weZ1vQnSFT7B
Gg4vr1lcqskwYTH7sh+bpsDTUeANr7QaknWKnaomroz+IUO8m9ig6RKtegaXhQCj
xswI4458S3nklqnoGMa56j46VYwft8YHO1lBiR1WefTHylknyng9Tdvf9G5mnzVg
wyrMTuT36lMXIa5KcSZeECIt2ZUT6KSSjWzEKZNXL5lS3gfUo7o=
=powp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,vhost,virtio: misc fixes
Just a bunch of bugfixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 30 Oct 2020 12:44:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
intel_iommu: Fix two misuse of "0x%u" prints
virtio: skip guest index check on device load
vhost-blk: set features before setting inflight feature
pci: Disallow improper BAR registration for type 1
pci: Change error_report to assert(3)
pci: advertise a page aligned ATS
pc: Implement -no-hpet as sugar for -machine hpet=on
vhost: Don't special case vq->used_phys in vhost_get_log_size()
pci: Assert irqnum is between 0 and bus->nirqs in pci_bus_change_irq_level
hw/pci: Extract pci_bus_change_irq_level() from pci_change_irq_level()
hw/virtio/vhost-vdpa: Fix Coverity CID 1432864
acpi/crs: Support ranges > 32b for hosts
acpi/crs: Prevent bad ranges for host bridges
vhost-vsock: set vhostfd to non-blocking mode
vhost-vdpa: negotiate VIRTIO_NET_F_STATUS with driver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Message-Id: <20200910134851.7817-1-jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Get rid of yet another global variable.
The default will be hpet=on only if CONFIG_HPET=y.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20201021144716.1536388-1-ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
-----BEGIN PGP SIGNATURE-----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=igPS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.2-20201028' into staging
ppc patch queue 2020-10-28
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
# gpg: Signature made Tue 27 Oct 2020 14:13:21 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.2-20201028:
ppc/: fix some comment spelling errors
spapr: Improve spapr_reallocate_hpt() error reporting
target/ppc: Fix kvmppc_load_htab_chunk() error reporting
spapr: Use error_append_hint() in spapr_reallocate_hpt()
spapr: Simplify error handling in spapr_memory_plug()
spapr: Pass &error_abort when getting some PC DIMM properties
spapr: Use appropriate getter for PC_DIMM_SLOT_PROP
spapr: Use appropriate getter for PC_DIMM_ADDR_PROP
pc-dimm: Drop @errp argument of pc_dimm_plug()
spapr: Simplify spapr_cpu_core_realize() and spapr_cpu_core_unrealize()
spapr: Make spapr_cpu_core_unrealize() idempotent
spapr: Drop spapr_delete_vcpu() unused argument
spapr: Unrealize vCPUs with qdev_unrealize()
spapr: Fix leak of CPU machine specific data
spapr: Move spapr_create_nvdimm_dr_connectors() to core machine code
hw/net: move allocation to the heap due to very large stack frame
ppc/spapr: re-assert IRQs during event-scan if there are pending
spapr: Clarify why DR connectors aren't user creatable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Store the child object directly within the sparc32-espdma object rather than
using link properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Store the child object directly within the sparc32-ledma object rather than
using link properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Store the child objects directly within the sparc32-dma object rather than using
link properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
-----BEGIN PGP SIGNATURE-----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=inaF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/led-api-20201026' into staging
API to model LED.
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
# gpg: Signature made Mon 26 Oct 2020 22:03:59 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/led-api-20201026:
hw/arm/tosa: Replace fprintf() calls by LED devices
hw/misc/mps2-scc: Use the LED device
hw/misc/mps2-fpgaio: Use the LED device
hw/arm/aspeed: Add the 3 front LEDs drived by the PCA9552 #1
hw/misc/led: Emit a trace event when LED intensity has changed
hw/misc/led: Allow connecting from GPIO output
hw/misc/led: Add a LED device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
cpu_remove() got superseded by cpu_remove_sync() in commit dbadee4ff4,
but its prototype wasn't removed. We could possibly keep the shorter
cpu_remove() naming but it seems better to highligth that this blocks
until the CPU thread is joined.
Fixes: dbadee4ff4 ("cpus: join thread when removing a vCPU")
Cc: pbonzini@redhat.com
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <160268285707.1107461.15035929822602623985.stgit@bahia.lan>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
spapr_reallocate_hpt() has three users, two of which pass &error_fatal
and the third one, htab_load(), passes &local_err, uses it to detect
failures and simply propagates -EINVAL up to vmstate_load(), which will
cause QEMU to exit. It is thus confusing that spapr_reallocate_hpt()
doesn't return right away when an error is detected in some cases. Also,
the comment suggesting that the caller is welcome to try to carry on
seems like a remnant in this respect.
This can be improved:
- change spapr_reallocate_hpt() to always report a negative errno on
failure, either as reported by KVM or -ENOSPC if the HPT is smaller
than what was asked,
- use that to detect failures in htab_load() which is preferred over
checking &local_err,
- propagate this negative errno to vmstate_load() because it is more
accurate than propagating -EINVAL for all possible errors.
[dwg: Fix compile error due to omitted prelim patch]
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160371605460.305923.5890143959901241157.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As recommended in "qapi/error.h", add a bool return value to
spapr_add_lmbs() and spapr_add_nvdimm(), and use them instead
of local_err in spapr_memory_plug().
This allows to get rid of the error propagation overhead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309734178.2739814.3488437759887793902.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
pc_dimm_plug() doesn't use it. It only aborts on error.
Drop @errp and adapt the callers accordingly.
[dwg: Removed unused label to fix compile]
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309728447.2739814.12831204841251148202.stgit@bahia.lan>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_create_nvdimm_dr_connectors() function doesn't need to access
any internal details of the sPAPR NVDIMM implementation. Also, pretty
much like for the LMBs, only spapr_machine_init() is responsible for the
creation of DR connectors for NVDIMMs.
Make this clear by making this function static in hw/ppc/spapr.c.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160249772183.757627.7396780936543977766.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The armv7m systick timer is a 24-bit decrementing, wrap-on-zero,
clear-on-write counter. Our current implementation has various
bugs and dubious workarounds in it (for instance see
https://bugs.launchpad.net/qemu/+bug/1872237).
We have an implementation of a simple decrementing counter
and we put a lot of effort into making sure it handles the
interesting corner cases (like "spend a cycle at 0 before
reloading") -- ptimer.
Rewrite the systick timer to use a ptimer rather than
a raw QEMU timer.
Unfortunately this is a migration compatibility break,
which will affect all M-profile boards.
Among other bugs, this fixes
https://bugs.launchpad.net/qemu/+bug/1872237 :
now writes to SYST_CVR when the timer is enabled correctly
do nothing; when the timer is enabled via SYST_CSR.ENABLE,
the ptimer code will (because of POLICY_NO_IMMEDIATE_RELOAD)
arrange that after one timer tick the counter is reloaded
from SYST_RVR and then counts down from there, as the
architecture requires.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201015151829.14656-3-peter.maydell@linaro.org
Generic watchdog device model implementation as per ARM SBSA v6.0
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Message-id: 20201027015927.29495-2-shashi.mallela@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a clock input to the PL011 UART so we can compute the current baud
rate and trace it. This is intended for developers who wish to use QEMU
to e.g. debug their firmware or to figure out the baud rate configured
by an unknown/closed source binary.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Those reset values have been extracted from a Raspberry Pi 3 model B
v1.2, using the 2020-08-20 version of raspios. The dump was done using
the debugfs interface of the CPRMAN driver in Linux (under
'/sys/kernel/debug/clk'). Each exposed clock tree stage (PLLs, channels
and muxes) can be observed by reading the 'regdump' file (e.g.
'plla/regdump').
Those values are set by the Raspberry Pi firmware at boot time (Linux
expects them to be set when it boots up).
Some stages are not exposed by the Linux driver (e.g. the PLL B). For
those, the reset values are unknown and left to 0 which implies a
disabled output.
Once booted in QEMU, the final clock tree is very similar to the one
visible on real hardware. The differences come from some unimplemented
devices for which the driver simply disable the corresponding clock.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This simple mux sits between the PLL channels and the DSI0E and DSI0P
clock muxes. This mux selects between PLLA-DSI0 and PLLD-DSI0 channel
and outputs the selected signal to source number 4 of DSI0E/P clock
muxes. It is controlled by the cm_dsi0hsck register.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The clock multiplexers are the last clock stage in the CPRMAN. Each mux
outputs one clock signal that goes out of the CPRMAN to the SoC
peripherals.
Each mux has at most 10 sources. The sources 0 to 3 are common to all
muxes. They are:
0. ground (no clock signal)
1. the main oscillator (xosc)
2. "test debug 0" clock
3. "test debug 1" clock
Test debug 0 and 1 are actual clock muxes that can be used as sources to
other muxes (for debug purpose).
Sources 4 to 9 are mux specific and can be unpopulated (grounded). Those
sources are fed by the PLL channels outputs.
One corner case exists for DSI0E and DSI0P muxes. They have their source
number 4 connected to an intermediate multiplexer that can select
between PLLA-DSI0 and PLLD-DSI0 channel. This multiplexer is called
DSI0HSCK and is not a clock mux as such. It is really a simple mux from
the hardware point of view (see https://elinux.org/The_Undocumented_Pi).
This mux is not implemented in this commit.
Note that there is some muxes for which sources are unknown (because of
a lack of documentation). For those cases all the sources are connected
to ground in this implementation.
Each clock mux output is exported by the CPRMAN at the qdev level,
adding the suffix '-out' to the mux name to form the output clock name.
(E.g. the 'uart' mux sees its output exported as 'uart-out' at the
CPRMAN level.)
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PLLs are composed of multiple channels. Each channel outputs one clock
signal. They are modeled as one device taking the PLL generated clock as
input, and outputting a new clock.
A channel shares the CM register with its parent PLL, and has its own
A2W_CTRL register. A write to the CM register will trigger an update of
the PLL and all its channels, while a write to an A2W_CTRL channel
register will update the required channel only.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN PLLs generate a clock based on a prescaler, a multiplier and
a divider. The prescaler doubles the parent (xosc) frequency, then the
multiplier/divider are applied. The multiplier has an integer and a
fractional part.
This commit also implements the CPRMAN CM_LOCK register. This register
reports which PLL is currently locked. We consider a PLL has being
locked as soon as it is enabled (on real hardware, there is a delay
after turning a PLL on, for it to stabilize).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are 5 PLLs in the CPRMAN, namely PLL A, C, D, H and B. All of them
take the xosc clock as input and produce a new clock.
This commit adds a skeleton implementation for the PLLs as sub-devices
of the CPRMAN. The PLLs are instantiated and connected internally to the
main oscillator.
Each PLL has 6 registers : CM, A2W_CTRL, A2W_ANA[0,1,2,3], A2W_FRAC. A
write to any of them triggers a call to the (not yet implemented)
pll_update function.
If the main oscillator changes frequency, an update is also triggered.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 CPRMAN is the clock manager of the SoC. It is composed of a
main oscillator, and several sub-components (PLLs, multiplexers, ...) to
generate the BCM2835 clock tree.
This commit adds a skeleton of the CPRMAN, with a dummy register
read/write implementation. It embeds the main oscillator (xosc) from
which all the clocks will be derived.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN (clock controller) was mapped at the watchdog/power manager
address. It was also split into two unimplemented peripherals (CM and
A2W) but this is really the same one, as shown by this extract of the
Raspberry Pi 3 Linux device tree:
watchdog@7e100000 {
compatible = "brcm,bcm2835-pm\0brcm,bcm2835-pm-wdt";
[...]
reg = <0x7e100000 0x114 0x7e00a000 0x24>;
[...]
};
[...]
cprman@7e101000 {
compatible = "brcm,bcm2835-cprman";
[...]
reg = <0x7e101000 0x2000>;
[...]
};
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No code out of bcm2836.c uses (or requires) the BCM283XInfo
declarations. Move it locally to the C source file.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 chips have a single USB host port shared between
a USB 2.0 EHCI host controller and a USB 1.1 OHCI host controller. This
adds support for both of them.
Testing notes:
* With -device usb-kbd, qemu will automatically insert a full-speed
hub, and the keyboard becomes controlled by the OHCI controller.
* With -device usb-kbd,bus=usb-bus.0,port=1, the keyboard is directly
attached to the port without any hubs, and the device becomes
controlled by the EHCI controller since it's high speed capable.
* With -device usb-kbd,bus=usb-bus.0,port=1,usb_version=1, the
keyboard is directly attached to the port, but it only advertises
itself as full-speed capable, so it becomes controlled by the OHCI
controller.
In all cases, the keyboard device enumerates correctly.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The emulated nvme device (hw/block/nvme.c) is currently using an
internal Intel device id.
Prepare to change that by allocating a device id under the 1b36 (Red
Hat, Inc.) vendor id.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Some devices might want to know the return value of dma_memory_rw, so
pass it along instead of ignoring it.
There are no existing users of the return value, so this patch should be
safe.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 8 LEDs connected to the MCC.
This replaces the 'mps2_scc_leds' trace events by the generic
'led_set_intensity' event.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-7-f4bug@amsat.org>
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):
2.1 Overview of the MPS2 and MPS2+ hardware
The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:
* User switches and user LEDs:
- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.
Add the 2 LEDs connected to the FPGA.
This replaces the 'mps2_fpgaio_leds' trace events by the generic
'led_set_intensity' event.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-6-f4bug@amsat.org>
Some devices expose GPIO lines.
Add a GPIO qdev input to our LED device, so we can
connect a GPIO output using qdev_connect_gpio_out().
When used with GPIOs, the intensity can only be either
minium or maximum. This depends of the polarity of the
GPIO (which can be inverted).
Declare the GpioPolarity type to model the polarity.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-3-f4bug@amsat.org>
Add a LED device which can be connected to a GPIO output.
They can also be dimmed with PWM devices. For now we do
not implement the dimmed mode, but in preparation of a
future implementation, we start using the LED intensity.
LEDs are limited to a fixed set of colors.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-2-f4bug@amsat.org>
Add '-drive' support to OTP device. Allow users to assign a raw file
as OTP image.
test commands for 16k otp.img filled with zero:
$ dd if=/dev/zero of=./otp.img bs=1k count=16
$ ./qemu-system-riscv64 -M sifive_u -m 256M -nographic -bios none \
-kernel ../opensbi/build/platform/sifive/fu540/firmware/fw_payload.elf \
-d guest_errors -drive if=none,format=raw,file=otp.img
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201020033732.12921-3-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- Add write operation to update fuse data bit when PWE bit is on.
- Add array, fuse_wo, to store the 'written' status for all bits
of OTP to block the write operation.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20201020033732.12921-2-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of loading the kernel at a hardcoded start address, let's load
the kernel at the next aligned address after the end of the firmware.
This should have no impact for current users of OpenSBI, but will
allow loading a noMMU kernel at the start of memory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 46c00c4f15b42feb792090e3d74359e180a6d954.1602634524.git.alistair.francis@wdc.com
Instead of returning the unused entry address from riscv_load_firmware()
instead return the end address. Also return the end address from
riscv_find_and_load_firmware().
This tells the caller if a firmware was loaded and how big it is. This
can be used to determine the load address of the next image (usually the
kernel).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 558cf67162342d65a23262248b040563716628b2.1602634524.git.alistair.francis@wdc.com
Allow the user to specify the main application CPU for the sifive_u
machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: b8412086c8aea0eff30fb7a17f0acf2943381b6a.1602634524.git.alistair.francis@wdc.com
Since sifive_plic.h is used by hw/intc/sifive_plic.c,
it has to be in the public include directory. Move it.
Fixes: 84fcf3c151 ("hw/riscv: Move sifive_plic model to hw/intc")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1602578033-68384-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The helper generates an acpi dsdt device entry
for the xhci sysbus device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201020074844.5304-4-kraxel@redhat.com
Move a bunch of defines which might be needed outside core xhci
code to that place. Add XHCI_ prefixes to avoid name clashes.
No functional change.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Message-id: 20201020074844.5304-3-kraxel@redhat.com
Add a variable to x86 machine state instead of
hard-coding the PCI interrupts.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-4-kraxel@redhat.com
This peripheral has 1 free-running timer and 4 compare registers.
Only the free-running timer is implemented. Add support the
COMPARE registers (each register is wired to an IRQ).
Reference: "BCM2835 ARM Peripherals" datasheet [*]
chapter 12 "System Timer":
The System Timer peripheral provides four 32-bit timer channels
and a single 64-bit free running counter. Each channel has an
output compare register, which is compared against the 32 least
significant bits of the free running counter values. When the
two values match, the system timer peripheral generates a signal
to indicate a match for the appropriate channel. The match signal
is then fed into the interrupt controller.
This peripheral is used since Linux 3.7, commit ee4af5696720
("ARM: bcm2835: add system timer").
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20201010203709.3116542-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The variable holding the CTRL_STATUS register is misnamed
'status'. Rename it 'ctrl_status' to make it more obvious
this register is also used to control the peripheral.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BCM2835_SYSTIMER_COUNT definition instead of the
magic '4' value.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently a single watch on /local/domain/X/backend is registered by each
QEMU process running in service domain X (where X is usually 0). The purpose
of this watch is to ensure that QEMU is notified when the Xen toolstack
creates a new device backend area.
Such a backend area is specific to a single frontend area created for a
specific guest domain and, since each QEMU process is also created to service
a specfic guest domain, it is unnecessary and inefficient to notify all QEMU
processes.
Only the QEMU process associated with the same guest domain need
receive the notification. This patch re-factors the watch registration code
such that notifications are targetted appropriately.
Reported-by: Jerome Leseinne <jerome.leseinne@gmail.com>
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20201001081500.1026-1-paul@xen.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20200902224311.1321159-58-ehabkost@redhat.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAl+NPIweHG1hcmsuY2F2
ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIf22AH/0e9QXSd2g7YRK2D
3NY/HuHr+lZNkDtNJanIQ9FUbmyzB9fMux4xg7BabpyY89Zwd9viivc6DrkM5fGM
12Yuq1IX/JOvolRvAMszAxUdnlLcB6OHDGrNBDyNFPK4Y87DLm86RJMTviiN/J/G
vsnCDjuxyHYtBruBbB4e6W/0nYJsfFXsopZxfV9Baain3W1uytRUW8WnjHJsvhhe
c7Dl4j5LcmXINtLn577kJIiVgZruk9FqADAnAcUM7+I0QRnhebshAoTpTzYCPAIy
LmUkr5NHtujBsa3m1zI8tjevFhCjvHOYvH6vdrMG6WO8m5DnAnv1iYYuM4xzI0yB
puOyz48=
=ShX6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mcayland/tags/qemu-macppc-20201019' into staging
qemu-macppc updates
# gpg: Signature made Mon 19 Oct 2020 08:13:16 BST
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* remotes/mcayland/tags/qemu-macppc-20201019:
mac_oldworld: Change PCI address of macio to match real hardware
mac_oldworld: Drop some variables
mac_oldworld: Drop a variable, use get_system_memory() directly
mac_newworld: Allow loading binary ROM image
mac_oldworld: Allow loading binary ROM image
m48t59: remove legacy m48t59_init() function
ppc405_boards: use qdev properties instead of legacy m48t59_init() function
sun4u: use qdev properties instead of legacy m48t59_init() function
sun4m: use qdev properties instead of legacy m48t59_init() function
m48t59-isa: remove legacy m48t59_init_isa() function
uninorth: use qdev gpios for PCI IRQs
grackle: use qdev gpios for PCI IRQs
macio: don't reference serial_hd() directly within the device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAl+K+NkACgkQ4+MsLN6t
wN4oPRAArZ5v0fjGrylt9g4xCAygLoSMkH3sZxltB77UVN/dCawSTLK2seKKO5g/
UtGt/j4/OAt8Ms+nF8FT+UZbknkgq+h7coOorHvz6gDEAx9UIg6/S2TRZJEx28+l
LbzkqdxvNSoHRrQDpGo43xoaxjzCxSTSOKpPfje6p2YDxWjkxdr/ahcsbKHSKc+x
uGdVdEAlLiAs/fBhkaJD3yy1VfqJKu8V5JJo1g4gSQOD1worRbZ4Us9QfuYr79Q7
Kce1Z1MQSf/TceZuDubhzZBep5lF1uW4lTywcaDby0LvGNK4K+RnH+i+t7CNhtKs
LH5j6iFQY1ecjb1Vh0IgKNAFaM2sTtO7A6fbBSOkVTO60wEp7i9fpbI5TRIjv7z/
EBkzP3n00hhbFFDci6Lnh/Ko0Xy0ODe3Um5l410sTnJe9+LK0HR5V6WH8PD/wKV2
nnKzSgb1U51KS6+FzLGLbQzDEvCgRKAJ9mwiQ+dlRfFHj+rEM6a9rlQmtsADBhKi
sEx62BKe6mM/+qQL9AOwZ5xBmFAn6wquuLYoA2Bwfg0wPIiAiFTwrz/eVSm9qYsw
O9Fer+1IMmd06T1REUtSDAh8+D2ekknKmFA3AG0818WvluD0Qm3KZp8uLLHJ/XkO
jiRtmeW+hApeh8hP4E0bzmrfJPKseBCYYP1By7XavIOoCxlqhew=
=BOxw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-next-20201017' into staging
MIPS patches queue
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
# gpg: Signature made Sat 17 Oct 2020 14:59:53 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-next-20201017: (44 commits)
target/mips: Increase number of TLB entries on the 34Kf core (16 -> 64)
MAINTAINERS: Remove duplicated Malta test entries
MAINTAINERS: Downgrade MIPS Boston to 'Odd Fixes', fix Paul Burton mail
MAINTAINERS: Put myself forward for MIPS target
MAINTAINERS: Remove myself
docs/system: Update MIPS CPU documentation
tests/acceptance: Add MIPS record/replay tests
hw/mips: Remove exit(1) in case of missing ROM
hw/mips: Rename TYPE_MIPS_BOSTON to TYPE_BOSTON
hw/mips: Simplify code using ROUND_UP(INITRD_PAGE_SIZE)
hw/mips: Simplify loading 64-bit ELF kernels
hw/mips/malta: Use clearer qdev style
hw/mips/malta: Move gt64120 related code together
hw/mips/malta: Fix FPGA I/O region size
target/mips/cpu: Display warning when CPU is used without input clock
hw/mips/cps: Do not allow use without input clock
hw/mips/malta: Set CPU frequency to 320 MHz
hw/mips/boston: Set CPU frequency to 1 GHz
hw/mips/cps: Expose input clock and connect it to CPU cores
hw/mips/jazz: Correct CPU frequencies
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that all of the callers of this function have been switched to use qdev
properties, this legacy init function can now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201016182739.22875-6-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This function is no longer used within the codebase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201016182739.22875-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently an object link property is used to pass a reference to the OpenPIC
into the PCI host bridge so that pci_unin_init_irqs() can connect the PCI
IRQs to the PIC itself.
This can be simplified by defining the PCI IRQs as qdev gpios and then wiring
up the PCI IRQs to the PIC in the New World machine init function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201013114922.2946-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of using a INITRD_PAGE_MASK definition, use the
simpler INITRD_PAGE_SIZE one which allows us to simplify
the code by using directly the self-explicit ROUND_UP()
macro.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200927163943.614604-3-f4bug@amsat.org>
Expose a qdev input clock named 'clk-in', and connect it to each
core to forward-propagate the clock.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-18-f4bug@amsat.org>
This function creates a clock and parents it to another object with a
given name. It calls clock_setup_canonical_path before returning the
new clock.
This function is useful to create clocks in devices when one doesn't
want to expose it at the qdev level (as an input or an output).
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201010135759.437903-4-luc@lmichel.fr>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Implement the ability of marking some versions deprecated. When
that CPU model is chosen, print a warning. The warning message
can be customized, e.g. suggesting an alternative CPU model to be
used instead.
The deprecation message will be printed by x86_cpu_list_entry(),
e.g. '-cpu help'.
QMP command 'query-cpu-definitions' will return a bool value
indicating the deprecation status.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1600758855-80046-1-git-send-email-robert.hu@linux.intel.com>
[ehabkost: reword commit message]
[ehabkost: Handle NULL cpu_type]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add scsi_device_get which finds the scsi device
and takes a reference to it.
Suggested-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200913160259.32145-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-12-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some code might race with placement of new devices on a bus.
We currently first place a (unrealized) device on the bus
and then realize it.
As a workaround, users that scan the child device list, can
check the realized property to see if it is safe to access such a device.
Use an atomic write here too to aid with this.
A separate discussion is what to do with devices that are unrealized:
It looks like for this case we only call the hotplug handler's unplug
callback and its up to it to unrealize the device.
An atomic operation doesn't cause harm for this code path though.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-10-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes the race between device emulation code that tries to find
a child device to dispatch the request to (e.g a scsi disk),
and hotplug of a new device to that bus.
Note that this doesn't convert all the readers of the list
but only these that might go over that list without BQL held.
This is a very small first step to make this code thread safe.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-5-mlevitsk@redhat.com>
[Use RCU_READ_LOCK_GUARD in more places, adjust testcase now that
the delay in DEVICE_DELETED due to RCU is more consistent. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-9-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check if an address is free on the bus before plugging in the
device. This makes it possible to do the check without any
side effects, and to detect the problem early without having
to do it in the realize callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some objects accidentally inherit ObjectClass instead of Object.
They compile silently but may crash after downcasting.
In this patch, we introduce a coccinelle script to find broken
declarations and fix them manually with proper base type.
Signed-off-by: Sergey Nizovtsev <snizovtsev@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The changes to come to NUMA support are all guest visible. In
theory we could just create a new 5_1 class option flag to
avoid the changes to cascade to 5.1 and under. The reality is that
these changes are only relevant if the machine has more than one
NUMA node. There is no need to change guest behavior that has
been around for years needlesly.
This new helper will be used by the next patches to determine
whether we should retain the (soon to be) legacy NUMA behavior
in the pSeries machine. The new behavior will only be exposed
if:
- machine is pseries-5.2 and newer;
- more than one NUMA node is declared in NUMA state.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20201007172849.302240-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As recommended in "qapi/error.h", return true on success and false on
failure. This allows to reduce error propagation overhead in the callers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200914123505.612812-14-groug@kaod.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As recommended in "qapi/error.h", return true on success and false on
failure. This allows to reduce error propagation overhead in the callers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200914123505.612812-13-groug@kaod.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As recommended in "qapi/error.h", return true on success and false on
failure. This allows to reduce error propagation overhead in the callers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200914123505.612812-11-groug@kaod.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As recommended in "qapi/error.h", return true on success and false on
failure. This allows to reduce error propagation overhead in the callers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200914123505.612812-9-groug@kaod.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We add the kvm-steal-time CPU property and implement it for machvirt.
A tiny bit of refactoring was also done to allow pmu and pvtime to
use the same vcpu device helper functions.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-7-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201002080935.1660005-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvm: uses the generic handler
qtest: uses the generic handler
whpx: changed to use the generic handler (identical implementation)
hax: changed to use the generic handler (identical implementation)
hvf: changed to use the generic handler (identical implementation)
tcg: adapt tcg-cpus to point to the tcg-specific handler
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DIAGNOSE 0x318 (diag318) is an s390 instruction that allows the storage
of diagnostic information that is collected by the firmware in the case
of hardware/firmware service events.
QEMU handles the instruction by storing the info in the CPU state. A
subsequent register sync will communicate the data to the hypervisor.
QEMU handles the migration via a VM State Description.
This feature depends on the Extended-Length SCCB (els) feature. If
els is not present, then a warning will be printed and the SCLP bit
that allows the Linux kernel to execute the instruction will not be
set.
Availability of this instruction is determined by byte 134 (aka fac134)
bit 0 of the SCLP Read Info block. This coincidentally expands into the
space used for CPU entries, which means VMs running with the diag318
capability may not be able to read information regarding all CPUs
unless the guest kernel supports an extended-length SCCB.
This feature is not supported in protected virtualization mode.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-9-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As more features and facilities are added to the Read SCP Info (RSCPI)
response, more space is required to store them. The space used to store
these new features intrudes on the space originally used to store CPU
entries. This means as more features and facilities are added to the
RSCPI response, less space can be used to store CPU entries.
With the Extended-Length SCCB (ELS) facility, a KVM guest can execute
the RSCPI command and determine if the SCCB is large enough to store a
complete reponse. If it is not large enough, then the required length
will be set in the SCCB header.
The caller of the SCLP command is responsible for creating a
large-enough SCCB to store a complete response. Proper checking should
be in place, and the caller should execute the command once-more with
the large-enough SCCB.
This facility also enables an extended SCCB for the Read CPU Info
(RCPUI) command.
When this facility is enabled, the boundary violation response cannot
be a result from the RSCPI, RSCPI Forced, or RCPUI commands.
In order to tolerate kernels that do not yet have full support for this
feature, a "fixed" offset to the start of the CPU Entries within the
Read SCP Info struct is set to allow for the original 248 max entries
when this feature is disabled.
Additionally, this is introduced as a CPU feature to protect the guest
from migrating to a machine that does not support storing an extended
SCCB. This could otherwise hinder the VM from being able to read all
available CPU entries after migration (such as during re-ipl).
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-7-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The header contained within the SCCB passed to the SCLP service call
contains the actual length of the SCCB. Instead of allocating a static
4K size for the work sccb, let's allow for a variable size determined
by the value in the header. The proper checks are already in place to
ensure the SCCB length is sufficent to store a full response and that
the length does not cross any explicitly-set boundaries.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20200915194416.107460-4-walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
(In QEMU, we call this the "select" register.)
My memory isn't good enough to memorize what these magic runes
do. Label them to prevent mixups from happening in the future.
Side note: I assume it's safe to always set 0xA0 even though ATA2 claims
these bits are reserved, because ATA3 immediately reinstated that these
bits should be always on. ATA4 and subsequent specs only claim that the
fields are obsolete, so I assume it's safe to leave these set and that
it should work with the widest array of guests.
Signed-off-by: John Snow <jsnow@redhat.com>
I have been staring at this FIXME for years and I never knew what it
meant. I finally stumbled across it!
When writing to the command registers, the old value is shifted into a
HOB copy of the register and the new value is written into the primary
register. When reading registers, the value retrieved is dependent on
the HOB bit in the CONTROL register.
By setting bit 7 (0x80) in CONTROL, any register read will, if it has
one, yield the HOB value for that register instead.
Our code has a problem: We were using bit 7 of the DEVICE register to
model this. We use bus->cmd roughly as the control register already, as
it stores the value from ide_ctrl_write.
Lastly, all command register writes reset the HOB, so fix that, too.
Signed-off-by: John Snow <jsnow@redhat.com>
It's the Control register, part of the Control block -- Command is
misleading here. Rename all related functions and constants.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
* Make isar_feature_aa32_fp16_arith() handle M-profile
* Fix SVE splice
* Fix SVE LDR/STR
* Remove ignore_memory_transaction_failures on the raspi2
* raspi: Various cleanup/refactoring
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAl9169cZHHBldGVyLm1h
eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3l40EACLY1pu2qyCWA2VLNjwI6Xa
XScSzHH2cqq7GDRjloVAqbSp1PGnQc5agZT86im78yo6Xz7AMMg79dxyUTb4pv6d
dm0i3g610avVMphbpl1LCGuMEWq9mqsEkpSwj9KlkavZWCT5Qwp6FQj5YPLhF5Xt
lIH+vclXPUrhgIBHerOHAYMJQEjygBWeF2DQFcmjjEWL3bjD/n32SQ3TaYf8B3kE
Zt/XVB3gMDleitBCrzmfmMEvfXoCC2d5QcPkWM1LsDgZo+/llB99mI1ndHoQJexJ
clAZqggpVHCLhO3MwsRy1Nc2TkT8AdvYHfOk0I44/58VHARmgcOmPkY7VubsKVnz
No9cgdVQEbnfWK/kh4vUKNf1UBTZDnNim0BdNLo1YsxDnSsNLrQRDx3XKg03653p
49Dp9u0/w3iqTNvdil8kBUVIH/ACwuEFJ79YAQaQ5J2XR7hen57GGZGuq/NVAcxp
fx1U0iwE9KBwSfrkhvCmZ0bTedyq1ZuaXp0Rf0Yrh3xWH2COHHr0fVCAZh23Pc7N
n5ovkUCfUozRvrCJsdP0sYk3JikYYfLet8nqAewTCM+Jc1gVAc55l8jmlUn+0O9p
RqNRktGFfNc6sS5H0ToysdIijeMrQqjClZbpON7NLH9/sFeWlf04NkF9CzDyKkQH
EAk6kXmxVkhECpj5KHkLTA==
=vKOh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20201001' into staging
target-arm queue:
* Make isar_feature_aa32_fp16_arith() handle M-profile
* Fix SVE splice
* Fix SVE LDR/STR
* Remove ignore_memory_transaction_failures on the raspi2
* raspi: Various cleanup/refactoring
# gpg: Signature made Thu 01 Oct 2020 15:46:47 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20201001:
hw/arm/raspi: Remove use of the 'version' value in the board code
hw/arm/raspi: Use RaspiProcessorId to set the firmware load address
hw/arm/raspi: Introduce RaspiProcessorId enum
hw/arm/raspi: Use more specific machine names
hw/arm/raspi: Avoid using TypeInfo::class_data pointer
hw/arm/raspi: Move arm_boot_info structure to RaspiMachineState
hw/arm/raspi: Load the firmware on the first core
hw/arm/raspi: Display the board revision in the machine description
hw/arm/raspi: Remove ignore_memory_transaction_failures on the raspi2
hw/arm/bcm2835: Add more unimplemented peripherals
hw/arm/raspi: Define various blocks base addresses
target/arm: Fix SVE splice
target/arm: Fix sve ldr/str
target/arm: Make isar_feature_aa32_fp16_arith() handle M-profile
target/arm: Add ID register values for Cortex-M0
hw/intc/armv7m_nvic: Only show ID register values for Main Extension CPUs
target/arm: Move id_pfr0, id_pfr1 into ARMISARegisters
target/arm: Replace ARM_FEATURE_PXN with ID_MMFR0.VMSA check
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bcm2835-v3d is used since Linux 4.7, see commit
49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree"),
and the bcm2835-txp since Linux 4.19, see commit
b7dd29b401f5 ("ARM: dts: bcm283x: Add Transposer block").
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20200921034729.432931-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Raspberry firmware is closed-source. While running it, it
accesses various I/O registers. Logging these accesses as UNIMP
(unimplemented) help to understand what the firmware is doing
(ideally we want it able to boot a Linux kernel).
Document various blocks we might use later.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20200921034729.432931-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU's kvmclock device is only created when KVM PV feature bits for
kvmclock (KVM_FEATURE_CLOCKSOURCE/KVM_FEATURE_CLOCKSOURCE2) are
exposed to the guest. With 'kvm=off' cpu flag the device is not
created and we don't call KVM_GET_CLOCK/KVM_SET_CLOCK upon migration.
It was reported that without these call at least Hyper-V TSC page
clocksouce (which can be enabled independently) gets broken after
migration.
Switch to creating kvmclock QEMU device unconditionally, it seems
to always make sense to call KVM_GET_CLOCK/KVM_SET_CLOCK on migration.
Use KVM_CAP_ADJUST_CLOCK check instead of CPUID feature bits.
Reported-by: Antoine Damhet <antoine.damhet@blade-group.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200922151934.899555-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PCMachineState type is only used under hw/i386/.
We don't need to forward-declare it for all architectures,
restrict it to the X86 one.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
xen_hvm_init() is restricted to the X86 architecture.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
xen_hvm_init() is only meanful to initialize a X86/PC machine,
rename it as xen_hvm_init_pc().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the "wakeup" property introduced in commit 9826fd597d
("suspend: make serial ports wakeup the guest") a boolean.
As we want to reuse the generic serial properties in the
ISA model (next commit), expose this property.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200907015535.827885-6-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
TYPE_SERIAL_IO is a subset of TYPE_SERIAL_MM, and it is
not used anymore. Remove it.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200907011538.818996-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
it was deprecated since 4.1
commit 4bb4a2732e (numa: deprecate implict memory distribution between nodes)
Users of existing VMs, wishing to preserve the same RAM distribution,
should configure it explicitly using ``-numa node,memdev`` options.
Current RAM distribution can be retrieved using HMP command
`info numa` and if separate memory devices (pc|nv-dimm) are present
use `info memory-device` and subtract device memory from output of
`info numa`.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200911084410.788171-2-imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Qemu will send GET_INFLIGHT_FD and SET_INFLIGH_FD to backend, and
the backend setup the inflight memory to track the io.
Change-Id: I805d6189996f7a1b44c65f0b12ef7473b1789510
Signed-off-by: Li Feng <fengli@smartx.com>
Message-Id: <20200909122021.1055174-1-fengli@smartx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Uses the existing gpex device which is also used as pcie host bridge on
arm/aarch64. For now only a 32bit mmio window and no ioport support.
It is disabled by default, use "-machine microvm,pcie=on" to enable.
ACPI support must be enabled too because the bus is declared in the
DSDT table.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-6-kraxel@redhat.com
Add a comment with a table listing the IRQs,
both legacy pc and microvm side-by-side.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-5-kraxel@redhat.com
Add helper function to generate dsdt aml code for the gpex pci host.
Largely copied from arm/virt. Configuration is handled by passing
a config struct instead of looked up from memory map.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-3-kraxel@redhat.com
It is defined twice already. Move to a common header file to
remove duplication and make it available to everybody.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-2-kraxel@redhat.com
Only qemu-system-FOO and qemu-storage-daemon provide QMP
monitors, therefore such declarations and definitions are
irrelevant for user-mode emulation.
Extracting the ACPI commands to their own schema reduces the size of
the qapi-misc* headers generated, and pulls less QAPI-generated code
into user-mode.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-8-philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Only qemu-system-FOO and qemu-storage-daemon provide QMP
monitors, therefore such declarations and definitions are
irrelevant for user-mode emulation.
Restricting the memory commands to machine.json pulls less
QAPI-generated code into user-mode.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-7-philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Restricting LostTickPolicy to machine.json pulls slightly less
QAPI-generated code into user-mode.
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-2-philmd@redhat.com>
[Add rationale to commit message]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Replace dpi with width_mm/height_mm in qemu_edid_info.
Use it when set (non-zero) to compute the DPI and generate the EDID.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20200927145751.365446-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When CPU hotplug with SMI has been negotiated, describe the SMI
register block in the DSDT. Pass the ACPI name of the SMI control
register to build_cpus_aml(), so that CPU_SCAN_METHOD can access the
register in the next patch.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Expose the "smi_negotiated_features" field of ICH9LPCState as
a QOM property.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will allow firmware to notify QEMU that firmware requires SMI
being triggered on CPU hot[un]plug, so that it would be able to account
for hotplugged CPU and relocate it to new SMM base and/or safely remove
CPU on unplug.
Using negotiated features, follow up patches will insert SMI upcall
into AML code, to make sure that firmware processes hotplug before
guest OS would attempt to use new CPU.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 9b3a35ec82 ("virtio: verify that legacy support is not accidentally
on") added a check that returns an error if legacy support is on, but the
device does not support legacy.
Unfortunately some devices were wrongly declared legacy capable even if
they were not (e.g vhost-vsock).
To avoid migration issues, we add a virtio-device property
(x-disable-legacy-check) to skip the legacy error, printing a warning
instead, for machine types < 5.1.
Cc: qemu-stable@nongnu.org
Fixes: 9b3a35ec82 ("virtio: verify that legacy support is not accidentally on")
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200921122506.82515-2-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These were deprecated since 4.0, remove both HMP and QMP variants.
Users should use device_add command instead. To get list of
possible CPUs and options, use 'info hotpluggable-cpus' HMP
or query-hotpluggable-cpus QMP command.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200915120403.1074579-1-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-user devices can get a disconnect in the middle of the VHOST-USER
handshake on the migration start. If disconnect event happened right
before sending next VHOST-USER command, then the vhost_dev_set_log()
call in the vhost_migration_log() function will return error. This error
will lead to the assert() and close the QEMU migration source process.
For the vhost-user devices the disconnect event should not break the
migration process, because:
- the device will be in the stopped state, so it will not be changed
during migration
- if reconnect will be made the migration log will be reinitialized as
part of reconnect/init process:
#0 vhost_log_global_start (listener=0x563989cf7be0)
at hw/virtio/vhost.c:920
#1 0x000056398603d8bc in listener_add_address_space (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2664
#2 0x000056398603dd30 in memory_listener_register (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2740
#3 0x0000563985fd6956 in vhost_dev_init (hdev=0x563989cf7bd8,
opaque=0x563989cf7e30, backend_type=VHOST_BACKEND_TYPE_USER,
busyloop_timeout=0)
at hw/virtio/vhost.c:1385
#4 0x0000563985f7d0b8 in vhost_user_blk_connect (dev=0x563989cf7990)
at hw/block/vhost-user-blk.c:315
#5 0x0000563985f7d3f6 in vhost_user_blk_event (opaque=0x563989cf7990,
event=CHR_EVENT_OPENED)
at hw/block/vhost-user-blk.c:379
Update the vhost-user-blk device with the internal started_vu field which
will be used for initialization (vhost_user_blk_start) and clean up
(vhost_user_blk_stop). This additional flag in the VhostUserBlk structure
will be used to track whether the device really needs to be stopped and
cleaned up on a vhost-user level.
The disconnect event will set the overall VHOST device (not vhost-user) to
the stopped state, so it can be used by the general vhost_migration_log
routine.
Such approach could be propogated to the other vhost-user devices, but
better idea is just to make the same connect/disconnect code for all the
vhost-user devices.
This migration issue was slightly discussed earlier:
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg01509.html
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg05241.html
Signed-off-by: Dima Stepanov <dimastep@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <9fbfba06791a87813fcee3e2315f0b904cc6789a.1599813294.git.dimastep@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To speed up the memory mapping updating between vhost-vDPA and vDPA
device driver, this patch passes the IOTLB batching flags via IOTLB
API. Two new flags was introduced, VHOST_IOTLB_BATCH_BEGIN is a hint
that a bathced IOTLB updating may be initiated from the
userspace. VHOST_IOTLB_BATCH_END is a hint that userspace has finished
the updating:
VHOST_IOTLB_BATCH_BEGIN
VHOST_IOTLB_UPDATE/VHOST_IOTLB_INVALIDATE
...
VHOST_IOTLB_BATCH_END
Vhost-vDPA can then know that all mappings has been set and can do
optimization like passing all the mappings to the vDPA device driver.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200907104903.31551-4-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch tries to switch to use new kernel IOTLB format V2. Previous
version may have inconsistent ABI between 32bit and 64bit machines
because of the hole after type field. Refer kernel commit
("429711aec282 vhost: switch to use new message format") for more
information.
To enable this feature, qemu need to use a new ioctl
VHOST_SET_BACKEND_FEATURE with VHOST_BACKEND_F_IOTLB_MSG_V2 bit. A new
vhost setting backend features ops was introduced. And when we try to
set features for vhost dev, we will examine the support of new IOTLB
format and enable it. This process is total transparent to guest,
which means we can have different IOTLB message type in src and dst
during migration.
The conversion of IOTLB message is straightforward, just check the
type and behave accordingly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200907104903.31551-3-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
clang's C11 atomic_fetch_*() functions only take a C11 atomic type
pointer argument. QEMU uses direct types (int, etc) and this causes a
compiler error when a QEMU code calls these functions in a source file
that also included <stdatomic.h> via a system header file:
$ CC=clang CXX=clang++ ./configure ... && make
../util/async.c:79:17: error: address argument to atomic operation must be a pointer to _Atomic type ('unsigned int *' invalid)
Avoid using atomic_*() names in QEMU's atomic.h since that namespace is
used by <stdatomic.h>. Prefix QEMU's APIs with 'q' so that atomic.h
and <stdatomic.h> can co-exist. I checked /usr/include on my machine and
searched GitHub for existing "qatomic_" users but there seem to be none.
This patch was generated using:
$ git grep -h -o '\<atomic\(64\)\?_[a-z0-9_]\+' include/qemu/atomic.h | \
sort -u >/tmp/changed_identifiers
$ for identifier in $(</tmp/changed_identifiers); do
sed -i "s%\<$identifier\>%q$identifier%g" \
$(git grep -I -l "\<$identifier\>")
done
I manually fixed line-wrap issues and misaligned rST tables.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200923105646.47864-1-stefanha@redhat.com>
Fuzzing discovered that virtqueue_unmap_sg() is being called on modified
req->in/out_sg iovecs. This means dma_memory_map() and
dma_memory_unmap() calls do not have matching memory addresses.
Fuzzing discovered that non-RAM addresses trigger a bug:
void address_space_unmap(AddressSpace *as, void *buffer, hwaddr len,
bool is_write, hwaddr access_len)
{
if (buffer != bounce.buffer) {
^^^^^^^^^^^^^^^^^^^^^^^
A modified iov->iov_base is no longer recognized as a bounce buffer and
the wrong branch is taken.
There are more potential bugs: dirty memory is not tracked correctly and
MemoryRegion refcounts can be leaked.
Use the new iov_discard_undo() API to restore elem->in/out_sg before
virtqueue_push() is called.
Fixes: 827805a249 ("virtio-blk: Convert VirtIOBlockReq.out to structrue")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Buglink: https://bugs.launchpad.net/qemu/+bug/1890360
Message-Id: <20200917094455.822379-3-stefanha@redhat.com>
Commit a5d7eb6534 ("Add TSC2301 touchscreen & keypad controller")
added the MouseTransformInfo declaration in "ui/console.h",
however it is only used in "hw/input/tsc2xxx.h".
Reduce the structure exposure by moving it to the single include
where it is used.
This should fix a build failure on OpenBSD:
In file included from hw/arm/nseries.c:30:
In file included from include/hw/arm/omap.h:24:
In file included from include/hw/input/tsc2xxx.h:14:
include/ui/console.h:11:11: fatal error: 'epoxy/gl.h' file not found
# include <epoxy/gl.h>
^~~~~~~~~~~~
1 error generated.
gmake: *** [Makefile.ninja:1735:
libqemu-aarch64-softmmu.fa.p/hw_arm_nseries.c.o] Error 1
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200907010155.815131-1-f4bug@amsat.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
One of the goals of having less boilerplate on QOM declarations
is to avoid human error. Requiring an extra argument that is
never used is an opportunity for mistakes.
Remove the unused argument from OBJECT_DECLARE_TYPE and
OBJECT_DECLARE_SIMPLE_TYPE.
Coccinelle patch used to convert all users of the macros:
@@
declarer name OBJECT_DECLARE_TYPE;
identifier InstanceType, ClassType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_TYPE(InstanceType, ClassType,
- lowercase,
UPPERCASE);
@@
declarer name OBJECT_DECLARE_SIMPLE_TYPE;
identifier InstanceType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_SIMPLE_TYPE(InstanceType,
- lowercase,
UPPERCASE);
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200916182519.415636-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Drop superfluous parenthesis around VMPortReadFunc typedef
(added in d67f679d99, missed to remove when moved in e595112985).
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200505142836.16903-1-philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (SIFIVE_U_OTP, SIFIVE_U_PRCI). This needs to be addressed
to allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_U_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with a QOM type check
macro (SIFIVE_E_PRCI). This needs to be addressed to allow us to
transform the QOM type check macros into functions generated by
OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_E_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The cpu hotplug code handles the initialization of coldplugged cpus
too, so it is needed even in case cpu hotplug is not supported.
Move the code from pc to x86, so microvm can use it.
Move both plug and unplug to keep everything in one place, even
though microvm needs plug only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200915120909.20838-16-kraxel@redhat.com
Both pc and microvm machine types have a acpi_dev field.
Move it to the common base type.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200915120909.20838-15-kraxel@redhat.com
$subject says all. Can be controlled using -M microvm,acpi=on/off.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200915120909.20838-9-kraxel@redhat.com
Reference it via ops pointer instead, simliar to the vga one.
Removes hard symbol reference, needed to build virtio-gpu modular.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200914134224.29769-6-kraxel@redhat.com
When booting directly into a kernel, bypassing the boot loader, the CPU and
UART clocks are not set up correctly. This makes the system appear very
slow, and causes the initrd boot test to fail when optimization is off.
The UART clock must run at 24 MHz. The default 25 MHz reference clock
cannot achieve this, so switch to PLL2/2 @ 480 MHz, which works
perfectly with the default /20 divider.
The CPU clock should run at 800 MHz, so switch it to PLL1/2. PLL1 runs
at 800 MHz by default, so we need to double the feedback divider as well
to make it run at 1600 MHz (so PLL1/2 runs at 800 MHz).
We don't bother checking for PLL lock because we know our emulated PLLs
lock instantly.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-13-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements a device model for the NPCM7xx SPI flash controller.
Direct reads and writes, and user-mode transactions have been tested in
various modes. Protection features are not implemented yet.
All the FIU instances are available in the SoC's address space,
regardless of whether or not they're connected to actual flash chips.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-11-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This just implements the bare minimum to cause the boot block to skip
memory initialization.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-10-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This supports reading and writing OTP fuses and keys. Only fuse reading
has been tested. Protection is not implemented.
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-9-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds two new machines, both supported by OpenBMC:
- npcm750-evb: Nuvoton NPCM750 Evaluation Board.
- quanta-gsj: A board with a NPCM730 chip.
They rely on the NPCM7xx SoC device to do the heavy lifting. They are
almost completely identical at the moment, apart from the SoC type,
which currently only changes the reset contents of one register
(GCR.MDLR), but they might grow apart a bit more as more functionality
is added.
Both machines can boot the Linux kernel into /bin/sh.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-6-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Nuvoton NPCM7xx SoC family are used to implement Baseboard
Management Controllers in servers. While the family includes four SoCs,
this patch implements limited support for two of them: NPCM730 (targeted
for Data Center applications) and NPCM750 (targeted for Enterprise
applications).
This patch includes little more than the bare minimum needed to boot a
Linux kernel built with NPCM7xx support in direct-kernel mode:
- Two Cortex-A9 CPU cores with built-in periperhals.
- Global Configuration Registers.
- Clock Management.
- 3 Timer Modules with 5 timers each.
- 4 serial ports.
The chips themselves have a lot more features, some of which will be
added to the model at a later stage.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-5-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 SoCs have three timer modules each holding five
timers and some shared registers (e.g. interrupt status).
Each timer runs at 25 MHz divided by a prescaler, and counts down from a
configurable initial value to zero. When zero is reached, the interrupt
flag for the timer is set, and the timer is disabled (one-shot mode) or
reloaded from its initial value (periodic mode).
This implementation is sufficient to boot a Linux kernel configured for
NPCM750. Note that the kernel does not seem to actually turn on the
interrupts.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-4-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enough functionality to boot the Linux kernel has been implemented. This
includes:
- Correct power-on reset values so the various clock rates can be
accurately calculated.
- Clock enables stick around when written.
In addition, a best effort attempt to implement SECCNT and CNTR25M was
made even though I don't think the kernel needs them.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-3-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a device model for the System Global Control Registers in the
NPCM730 and NPCM750 BMC SoCs.
This is primarily used to enable SMP boot (the boot ROM spins reading
the SCRPAD register) and DDR memory initialization; other registers are
best effort for now.
The reset values of the MDLR and PWRON registers are determined by the
SoC variant (730 vs 750) and board straps respectively.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_test model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_uart model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move riscv_htif model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_otp model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_e_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a platform DMA controller with 4 DMA
channels. This connects the exsiting SiFive PDMA model to the SoC,
and adds its device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-17-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the CLINT timestamp is using a hard-coded timebase
frequency value SIFIVE_CLINT_TIMEBASE_FREQ. This might not be
true for all boards.
Add a new 'timebase-freq' property to the CLINT device, and
update various functions to accept this as a parameter.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-16-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 3 GPIOs controllers. It seems
enough to create unimplemented devices to cover their register
spaces at this point.
With this commit, QEMU can boot to U-Boot (2nd stage bootloader)
all the way to the Linux shell login prompt, with a modified HSS
(1st stage bootloader).
For detailed instructions on how to create images for the Icicle
Kit board, please check QEMU RISC-V WiKi page at:
https://wiki.qemu.org/Documentation/Platforms/RISCV
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-15-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 2 Candence GEMs to provide
IEEE 802.3 standard-compliant 10/100/1000 Mbps ethernet interface.
On the Icicle Kit board, GEM0 connects to a PHY at address 8 while
GEM1 connects to a PHY at address 9.
The 2nd stage bootloader (U-Boot) is using GEM1 by default, so we
must specify 2 '-nic' options from the command line in order to get
a working ethernet.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-14-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the PHY address of the PHY connected to GEM is hard-coded
to either 23 (BOARD_PHY_ADDRESS) or 0. This might not be the case for
all boards. Add a new 'phy-addr' property so that board can specify
the PHY address for each GEM instance.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the Icicle Kit board, the HSS firmware utilizes the on-chip DMA
controller to move the 2nd stage bootloader in the system memory.
Let's connect a DMA controller to Microchip PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates a DMA engine that supports:
* Independent concurrent DMA transfers using 4 DMA channels
* Generation of interrupts on various conditions during execution
which is actually an IP reused from the SiFive FU540 chip.
This creates a model to support both polling and interrupt modes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates one Cadence SDHCI controller.
On the Icicle Kit board, one eMMC chip and an external SD card
connect to this controller depending on different configuration.
As QEMU does not support eMMC yet, we just emulate the SD card
configuration. To test this, the Hart Software Services (HSS)
should choose the SD card configuration:
$ cp boards/icicle-kit-es/def_config.sdcard .config
$ make BOARD=icicle-kit-es
The SD card image can be built from the Yocto BSP at:
https://github.com/polarfire-soc/meta-polarfire-soc-yocto-bsp
Note the generated SD card image should be resized before use:
$ qemu-img resize /path/to/sdcard.img 4G
Launch QEMU with the following command:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit -sd sdcard.img
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cadence SD/SDIO/eMMC Host Controller (SD4HC) is an SDHCI compatible
controller. The SDHCI compatible registers start from offset 0x200,
which are called Slot Register Set (SRS) in its datasheet.
This creates a Cadence SDHCI model built on top of the existing
generic SDHCI model. Cadence specific Host Register Set (HRS) is
implemented to make guest software happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC has 5 MMUARTs, and the Icicle Kit board
wires 4 of them out. Let's connect all 5 MMUARTs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC MMUART is ns16550 compatible, with some
additional registers. Create a simple MMUART model built on top
of the existing ns16550 model.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an initial support for Microchip PolarFire SoC Icicle Kit.
The Icicle Kit board integrates a PolarFire SoC, with one SiFive's
E51 plus four U54 cores and many on-chip peripherals and an FPGA.
For more details about Microchip PolarFire Soc, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga
Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000.
The following perepherals are created as an unimplemented device:
- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
More devices will be added later.
The BIOS image used by this machine is hss.bin, aka Hart Software
Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services
To launch this machine:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit
The memory is set to 1 GiB by default to match the hardware.
A sanity check on ram size is performed in the machine init routine
to prompt user to increase the RAM size to > 1 GiB when less than
1 GiB ram is detected.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V machines do not instantiate RISC-V CPUs directly, instead
they do that via the hart array. Add a new property for the reset
vector address to allow the value to be passed to the CPU, before
CPU is realized.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200902224311.1321159-49-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200902224311.1321159-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This looks like a copy/paste mistake: the instance type checking
macro for TYPE_GPEX_ROOT_DEVICE was named MCH_PCI_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Separate run of the TypeCheckMacro converter using the --force
flag, for the cases where typedefs weren't found in the same
header nor in typedefs.h.
Generated initially using:
$ ./scripts/codeconverter/converter.py --force -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')
Then each case was manually reviewed, and a comment was added
indicating what's unusual about those type checking
macros/functions. Despite not following the usual pattern, the
changes in this patch were found to be safe.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200831210740.126168-15-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The work to be done in h_home_node_associativity() intersects
with what is already done in spapr_numa_fixup_cpu_dt(). This
patch creates a new helper, spapr_numa_get_vcpu_assoc(), to
be used for both spapr_numa_fixup_cpu_dt() and
h_home_node_associativity().
While we're at it, use memcpy() instead of loop assignment
to created the returned array.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200904172422.617460-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In a similar fashion as the previous patch, let's move the
handling of ibm,associativity-lookup-arrays from spapr.c to
spapr_numa.c. A spapr_numa_write_assoc_lookup_arrays() helper was
created, and spapr_dt_dynamic_reconfiguration_memory() can now
use it to advertise the lookup-arrays.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200903220639.563090-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Vcpus have an additional paramenter to be appended, vcpu_id. This
also changes the size of the of property itself, which is being
represented in index 0 of numa_assoc_array[cpu->node_id],
and defaults to MAX_DISTANCE_REF_POINTS for all cases but
vcpus.
All this logic makes more sense in spapr_numa.c, where we handle
everything NUMA and associativity. A new helper spapr_numa_fixup_cpu_dt()
was added, and spapr.c uses it the same way as it was using the former
spapr_fixup_cpu_numa_dt().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200903220639.563090-3-danielhb413@gmail.com>
[dwg: Correct uint to int type, which can break windows builds]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The next step to centralize all NUMA/associativity handling in
the spapr machine is to create a 'one stop place' for all
things ibm,associativity.
This patch introduces numa_assoc_array, a 2 dimensional array
that will store all ibm,associativity arrays of all NUMA nodes.
This array is initialized in a new spapr_numa_associativity_init()
function, called in spapr_machine_init(). It is being initialized
with the same values used in other ibm,associativity properties
around spapr files (i.e. all zeros, last value is node_id).
The idea is to remove all hardcoded definitions and FDT writes
of ibm,associativity arrays, doing instead a call to the new
helper spapr_numa_write_associativity_dt() helper, that will
be able to write the DT with the correct values.
We'll start small, handling the trivial cases first. The
remaining instances of ibm,associativity will be handled
next.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200903220639.563090-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only used inside spapr_nvdimm.c.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200901125645.118026-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We're going to make changes in how spapr handles all
ibm,associativity* related properties to enhance our current NUMA
support.
At this moment we have associativity code scattered all around
spapr_* files, with hardcoded values and array sizes. This
makes it harder to change any NUMA specific parameters in
the future. Having everything in the same place allows not
only for easier tuning, but also easier understanding since all
NUMA related code is on the same file.
This patch introduces a new file to gather all NUMA/associativity
handling code in spapr, spapr_numa.c. To get things started, let's
remove associativity-reference-points and max-associativity-domains
code from spapr_dt_rtas() to a new helper called spapr_numa_write_rtas_dt().
This will decouple spapr_dt_rtas() from the NUMA changes that
are going to happen in those two properties.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200901125645.118026-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are other platforms which also have CPUs that start powered off, so
generalize the start-powered-off property so that it can be used by them.
Note that ARMv7MState also has a property of the same name but this patch
doesn't change it because that class isn't a subclass of CPUState so it
wouldn't be a trivial change.
This change should not cause any change in behavior.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Message-Id: <20200826055535.951207-2-bauerman@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
NVDIMM has different contraints and conditions than the regular
DIMM and we'll need to add at least one more.
Instead of relying on 'if (nvdimm)' conditionals in the body of
spapr_memory_pre_plug(), use the existing spapr_nvdimm_validate_opts()
and put all NVDIMM handling code there. Rename it to
spapr_nvdimm_validate() to reflect that the function is now checking
more than the nvdimm device options. This makes spapr_memory_pre_plug()
a bit easier to follow, and we can tune in NVDIMM parameters
and validation in the same place.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200825215749.213536-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OPAL test suite runs a read-erase-write test on the PNOR :
https://github.com/open-power/op-test/blob/master/testcases/OpTestPNOR.py
which revealed that the IPMI HIOMAP handlers didn't support
HIOMAP_C_ERASE. Implement the sector erase command by writing 0xFF in
the PNOR memory region.
Cc: Corey Minyard <cminyard@mvista.com>
Reported-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200820164638.2515681-1-clg@kaod.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER9, the KVM XIVE device uses priority 7 for the escalation
interrupts. On POWER10, the host can use a reduced set of priorities
and KVM will configure the escalation priority to a lower number. In
any case, the guest is allowed to use priorities in a single range :
[ 0 .. (maxprio - 1) ].
Introduce a 'hv-prio' property to represent the escalation priority
number and use it to compute the "ibm,plat-res-int-priorities"
property defining the priority ranges reserved by the hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200819130843.2230799-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_drc.h includes typechecker macro boilerplate for the many different
DRC subclasses. However, most of these types don't actually have different
data in their class and/or instance, making these unneeded, unused, and in
fact a bad idea. Remove them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
* Two build system fixes to fix some failures the CI
* One m68k QOMification patch
* Some trivial qtest patches
* Some small improvements for the Gitlab CI
-----BEGIN PGP SIGNATURE-----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=kPTJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-09-03' into staging
* Cirrus-CI improvements and fixes (compile with -Werror & fix for 1h problem)
* Two build system fixes to fix some failures the CI
* One m68k QOMification patch
* Some trivial qtest patches
* Some small improvements for the Gitlab CI
# gpg: Signature made Thu 03 Sep 2020 12:04:32 BST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-09-03:
gitlab-ci.yml: Set artifacts expiration time
gitlab-ci.yml: Run check-qtest and check-unit at the end of the fuzzer job
gitlab/travis: Rework the disabled features tests
libqtest: Rename qmp_assert_error_class() to qmp_expect_error_and_unref()
tests/qtest/ipmi-kcs: Fix assert side-effect
tests/qtest/tpm: Declare input buffers const and static
tests/qtest/ahci: Improve error handling (NEGATIVE_RETURNS)
hw/m68k: QOMify the mcf5206 system integration module
configure: Add system = 'linux' for meson when cross-compiling
meson: fix keymaps without qemu-keymap
cirrus.yml: Split FreeBSD job into two parts
cirrus.yml: Update the macOS jobs to Catalina
cirrus.yml: Compile macOS with -Werror
cirrus.yml: Compile FreeBSD with -Werror
configure: Fix atomic64 test for --enable-werror on macOS
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
-----BEGIN PGP SIGNATURE-----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=ZQHA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20200901' into staging
Various fixes of Aspeed machines :
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
# gpg: Signature made Tue 01 Sep 2020 13:39:20 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20200901:
hw: add a number of SPI-flash's of m25p80 family
arm: aspeed: add strap define `25HZ` of AST2500
aspeed/smc: Open AHB window of the second chip of the AST2600 FMC controller
aspeed/sdmc: Simplify calculation of RAM bits
aspeed/sdmc: Allow writes to unprotected registers
aspeed/sdmc: Perform memory training
ftgmac100: Improve software reset
ftgmac100: Fix integer overflow in ftgmac100_do_tx()
ftgmac100: Check for invalid len and address before doing a DMA transfer
ftgmac100: Change interrupt status when a DMA error occurs
ftgmac100: Fix interrupt status "Packet moved to RX FIFO"
ftgmac100: Fix interrupt status "Packet transmitted on ethernet"
ftgmac100: Fix registers that can be read
aspeed/sdhci: Fix reset sequence
aspeed/smc: Fix max_slaves of the legacy SMC device
aspeed/smc: Fix MemoryRegionOps definition
hw/arm/aspeed: Add board model for Supermicro X11 BMC
aspeed/scu: Fix valid access size on AST2400
m25p80: Add support for n25q512ax3
m25p80: Return the JEDEC ID twice for mx25l25635e
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The mcf5206 system integration module should be a proper device.
Let's finally QOMify it.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200819065201.4045-1-huth@tuxfamily.org>
This reverts commit c24a41bb53.
Remove the EPYC specific apicid decoding and use the generic
default decoding.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <159889937478.21294.4192291354416942986.stgit@naples-babu.amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This reverts commit 7568b20555.
Remove the EPYC specific apicid decoding and use the generic
default decoding.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <159889936871.21294.1454526726636639780.stgit@naples-babu.amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This reverts commit 6121c7fbfd.
Remove the EPYC specific apicid decoding and use the generic
default decoding.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <159889935648.21294.8095493980805969544.stgit@naples-babu.amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the macro to be consistent with RDMA_PROVIDER and
RDMA_PROVIDER_GET_CLASS.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-48-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some QOM macros were using a X86_IOMMU_DEVICE prefix, and others
were using a X86_IOMMU prefix. Rename all of them to use the
same X86_IOMMU_DEVICE prefix.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-47-ehabkost@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the MOS6522_DEVICE_CLASS and MOS6522_DEVICE_GET_CLASS
macros to be consistent with the TYPE_MOS6522 and MOS6522 macros.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-46-ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to IMX_CCM_GET_CLASS to be consistent with the existing
IMX_CCM and IXM_CCM_CLASS macro.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-45-ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Provide a definition for the "25Hz reference clock input mode" strap
Signed-off-by: Igor Kononenko <i.kononenko@yadro.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200811203502.20382-1-i.kononenko@yadro.com>
Message-Id: <20200819100956.2216690-21-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This allows qemu to run the "normal" power on reset boot path through
u-boot, where the DDR is trained.
An enhancement would be to have the SCU bit stick across qemu reboots,
but be unset on initial boot.
Proper modelling would be to discard all writes to the phy setting regs
at offset 0x100 - 0x400 and to model the phy status regs at offset
0x400.
The status regs model would only need to account for offets 0x00,
0x50, 0x68 and 0x7c.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: checkpatch fixes ]
Message-Id: <20200819100956.2216690-17-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Group some HID values that are used pretty much everywhere when
dealing with HID devices.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200812094135.20550-2-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
TYPE_ARM_SSE is a TYPE_SYS_BUS_DEVICE subclass, but
ARMSSEClass::parent_class is declared as DeviceClass.
It never caused any problems by pure luck:
We were not setting class_size for TYPE_ARM_SSE, so class_size of
TYPE_SYS_BUS_DEVICE was being used (sizeof(SysBusDeviceClass)).
This made the system allocate enough memory for TYPE_ARM_SSE
devices even though ARMSSEClass was too small for a sysbus
device.
Additionally, the ARMSSEClass::info field ended up at the same
offset as SysBusDeviceClass::explicit_ofw_unit_address. This
would make sysbus_get_fw_dev_path() crash for the device.
Luckily, sysbus_get_fw_dev_path() never gets called for
TYPE_ARM_SSE devices, because qdev_get_fw_dev_path() is only used
by the boot device code, and TYPE_ARM_SSE devices don't appear at
the fw_boot_order list.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20200826181006.4097163-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To have a better idea of how big is the region where the offset
belongs, display the value with the width of the region size
(i.e. a region of 0x1000 bytes uses 0x000 format).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200812190206.31595-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clock canonical name is set in device_set_realized (see the block
added to hw/core/qdev.c in commit 0e6934f264).
If we connect a clock after the device is realized, this code is
not executed. This is currently not a problem as this name is only
used for trace events, however this disrupt tracing.
Add a comment to document qdev_connect_clock_in() must be called
before the device is realized, and assert this condition.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We want to assert the device is not realized. To avoid overloading
this header including "hw/qdev-core.h", uninline the function first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we want to call qdev_connect_clock_in() before the device
is realized, we need to uninline cadence_uart_create() first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The H3 SoC keeps using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814122907.27732-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The A10 and H3 SoC keep using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814110057.307-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Avoid propagating the clock change when the clock does not change.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200806123858.30058-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let clock_set() return a boolean value whether the clock
has been updated or not.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200806123858.30058-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
clock_init*() inlined funtions are simple wrappers around
clock_set*() and are not used. Remove them in favor of clock_set*().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200806123858.30058-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently we have a SWIM typedef and a SWIM type checking macro,
but OBJECT_DECLARE* would transform the SWIM macro into a
function, and the function name would conflict with the SWIM
typedef name.
Rename the struct and typedef to "Swim". This will make future
conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-50-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to be consistent with S390_CCW_MACHINE and
TYPE_S390_CCW_MACHINE.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-49-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the existing class type checking macros to be consistent
with the type name and instance type checking macro. Use a
NUBUS_MACFB prefix instead of MACFB_NUBUS.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-44-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-38-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-37-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-36-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move all declarations related to TYPE_VMBUS to the same place in
vmbus.h.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-35-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the I8042 macro close to the TYPE_I8042 define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-34-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the ALLWINNER_AHCI macro close to the TYPE_ALLWINNER_AHCI
define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the I8257 macro to i8257.h, close to the TYPE_I8257 define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-32-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The TYPE_* constants and the typedefs are defined in ahci.h, so
we can move the type checking macros there too.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the VHOST_USER_GPU type checking macro to virtio-gpu.h,
close to the TYPE_VHOST_USER_GPU #define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-30-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
In sclp.h, use "struct SCLPEventFacility" to avoid introducing
unnecessary header dependencies.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-29-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the typedef from spapr_irq.h to spapr.h, and use "struct
SpaprMachineState" in the spapr_*.h headers (to avoid circular
header dependencies).
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-28-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The typedef was used in the XENBACKEND_DEVICE macro, but it was
never defined. Define the typedef close to the type checking
macro.
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-27-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename TYPE_ARMSSE to TYPE_ARM_SSE, and ARMSSE*() type checking
macros to ARM_SSE*().
This will avoid a future conflict between an ARM_SSE() type
checking macro and the ARMSSE typedef name.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-26-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
PlatformBusDeviceClass doesn't exist. This will break when we
automatically convert the code to use OBJECT_DEFINE_TYPE().
Delete the macros that reference the non-existing typedef.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-25-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro never worked because the NubusBridge typedef doesn't
exist. Delete it.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-24-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-22-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-19-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-18-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro definition had an extra semicolon. This was never
noticed because the macro was only being used where it didn't
make a difference.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (IBEX_PLIC, IBEX_UART). This needs to be addressed to
allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to IBEX_DEV_*, to avoid conflicts.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-8-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros:
ASPEED_GPIO
ASPEED_I2C
ASPEED_RTC
ASPEED_SCU
ASPEED_SDHCI
ASPEED_SDMC
ASPEED_VIC
ASPEED_WDT
ASPEED_XDMA
This needs to be addressed to allow us to transform the QOM type
check macros into functions generated by OBJECT_DECLARE_TYPE().
Rename all the constants to ASPEED_DEV_*, to avoid conflicts.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (AW_H3_CCU, AW_H3_SYSCTRL). This needs to be addressed to
allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to AW_H3_DEV_*, to avoid conflicts.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Automatically size the number of request virtqueues to match the number
of vCPUs. This ensures that completion interrupts are handled on the
same vCPU that submitted the request. No IPI is necessary to complete
an I/O request and performance is improved. The maximum number of MSI-X
vectors and virtqueues limit are respected.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20200818143348.310613-8-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Automatically size the number of virtio-blk-pci request virtqueues to
match the number of vCPUs. Other transports continue to default to 1
request virtqueue.
A 1:1 virtqueue:vCPU mapping ensures that completion interrupts are
handled on the same vCPU that submitted the request. No IPI is
necessary to complete an I/O request and performance is improved. The
maximum number of MSI-X vectors and virtqueues limit are respected.
Performance improves from 78k to 104k IOPS on a 32 vCPU guest with 101
virtio-blk-pci devices (ioengine=libaio, iodepth=1, bs=4k, rw=randread
with NVMe storage).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Message-Id: <20200818143348.310613-7-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Automatically size the number of virtio-scsi-pci, vhost-scsi-pci, and
vhost-user-scsi-pci request virtqueues to match the number of vCPUs.
Other transports continue to default to 1 request virtqueue.
A 1:1 virtqueue:vCPU mapping ensures that completion interrupts are
handled on the same vCPU that submitted the request. No IPI is
necessary to complete an I/O request and performance is improved. The
maximum number of MSI-X vectors and virtqueues limit are respected.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200818143348.310613-6-stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The event and control virtqueues are always present, regardless of the
multi-queue configuration. Define a constant so that virtqueue number
calculations are easier to read.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20200818143348.310613-5-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We introduce a new global flag 'acpi-root-pci-hotplug' for i440fx with which
we can turn on or off PCI device hotplug on the root bus. This flag can be
used to prevent all PCI devices from getting hotplugged or unplugged from the
root PCI bus.
This feature is targetted mostly towards Windows VMs. It is useful in cases
where some hypervisor admins want to deploy guest VMs in a way so that the
users of the guest OSes are not able to hot-eject certain PCI devices from
the Windows system tray. Laine has explained the use case here in detail:
https://www.redhat.com/archives/libvir-list/2020-February/msg00110.html
Julia has resolved this issue for PCIE buses with the following commit:
530a096318 ("pcie_root_port: Add hotplug disabling option")
This commit attempts to introduce similar behavior for PCI root buses used in
i440fx machine types (although in this case, we do not have a per-slot
capability to turn hotplug on or off).
Usage:
-global PIIX4_PM.acpi-root-pci-hotplug=off
By default, this option is enabled which means that hotplug is turned on for
the PCI root bus.
The previously existing flag 'acpi-pci-hotplug-with-bridge-support' for PCI-PCI
bridges remain as is and can be used along with this new flag to control PCI
hotplug on PCI bridges.
This change has been tested using a Windows 2012R2 server guest image and also
with a Windows 2019 server guest image on a Ubuntu 18.04 host using the latest
master qemu from upstream.
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20200821165403.26589-1-ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
We extend RISC-V virt machine to allow creating a multi-socket
machine. Each RISC-V virt machine socket is a NUMA node having
a set of HARTs, a memory instance, a CLINT instance, and a PLIC
instance. Other devices are shared between all sockets. We also
update the generated device tree accordingly.
By default, NUMA multi-socket support is disabled for RISC-V virt
machine. To enable it, users can use "-numa" command-line options
of QEMU.
Example1: For two NUMA nodes with 2 CPUs each, append following
to command-line options: "-smp 4 -numa node -numa node"
Example2: For two NUMA nodes with 1 and 3 CPUs, append following
to command-line options:
"-smp 4 -numa node -numa node -numa cpu,node-id=0,core-id=0 \
-numa cpu,node-id=1,core-id=1 -numa cpu,node-id=1,core-id=2 \
-numa cpu,node-id=1,core-id=3"
The maximum number of sockets in a RISC-V virt machine is 8
but this limit can be changed in future.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-6-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend RISC-V spike machine to allow creating a multi-socket
machine. Each RISC-V spike machine socket is a NUMA node having
a set of HARTs, a memory instance, and a CLINT instance. Other
devices are shared between all sockets. We also update the
generated device tree accordingly.
By default, NUMA multi-socket support is disabled for RISC-V spike
machine. To enable it, users can use "-numa" command-line options
of QEMU.
Example1: For two NUMA nodes with 2 CPUs each, append following
to command-line options: "-smp 4 -numa node -numa node"
Example2: For two NUMA nodes with 1 and 3 CPUs, append following
to command-line options:
"-smp 4 -numa node -numa node -numa cpu,node-id=0,core-id=0 \
-numa cpu,node-id=1,core-id=1 -numa cpu,node-id=1,core-id=2 \
-numa cpu,node-id=1,core-id=3"
The maximum number of sockets in a RISC-V spike machine is 8
but this limit can be changed in future.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-5-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We add common helper routines which can be shared by RISC-V
multi-socket NUMA machines.
We have two types of helpers:
1. riscv_socket_xyz() - These helper assist managing multiple
sockets irrespective whether QEMU NUMA is enabled/disabled
2. riscv_numa_xyz() - These helpers assist in providing
necessary QEMU machine callbacks for QEMU NUMA emulation
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-4-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend PLIC emulation to allow multiple instances of PLIC in
a QEMU RISC-V machine. To achieve this, we remove first HART id
zero assumption from PLIC emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200616032229.766089-3-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend CLINT emulation to allow multiple instances of CLINT in
a QEMU RISC-V machine. To achieve this, we remove first HART id
zero assumption from CLINT emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-Id: <20200616032229.766089-2-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
* hw/cpu/a9mpcore: Verify the machine use Cortex-A9 cores
* hw/arm/smmuv3: Implement SMMUv3.2 range-invalidation
* docs/system/arm: Document the Xilinx Versal Virt board
* target/arm: Make M-profile NOCP take precedence over UNDEF
* target/arm: Use correct FPST for VCMLA, VCADD on fp16
* target/arm: Various cleanups preparing for fp16 support
-----BEGIN PGP SIGNATURE-----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=cuKX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20200824' into staging
target-arm queue:
* hw/cpu/a9mpcore: Verify the machine use Cortex-A9 cores
* hw/arm/smmuv3: Implement SMMUv3.2 range-invalidation
* docs/system/arm: Document the Xilinx Versal Virt board
* target/arm: Make M-profile NOCP take precedence over UNDEF
* target/arm: Use correct FPST for VCMLA, VCADD on fp16
* target/arm: Various cleanups preparing for fp16 support
# gpg: Signature made Mon 24 Aug 2020 10:47:14 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20200824: (27 commits)
target/arm: Use correct FPST for VCMLA, VCADD on fp16
target/arm: Implement FPST_STD_F16 fpstatus
target/arm: Make A32/T32 use new fpstatus_ptr() API
target/arm: Replace A64 get_fpstatus_ptr() with generic fpstatus_ptr()
target/arm: Delete unused ARM_FEATURE_CRC
target/arm/translate.c: Delete/amend incorrect comments
target/arm: Delete unused VFP_DREG macros
target/arm: Remove ARCH macro
target/arm: Convert T32 coprocessor insns to decodetree
target/arm: Do M-profile NOCP checks early and via decodetree
target/arm: Tidy up disas_arm_insn()
target/arm: Convert A32 coprocessor insns to decodetree
target/arm: Separate decode from handling of coproc insns
target/arm: Pull handling of XScale insns out of disas_coproc_insn()
docs/system/arm: Document the Xilinx Versal Virt board
hw/arm/smmuv3: Advertise SMMUv3.2 range invalidation
hw/arm/smmuv3: Support HAD and advertise SMMUv3.1 support
hw/arm/smmuv3: Let AIDR advertise SMMUv3.0 support
hw/arm/smmuv3: Fix IIDR offset
hw/arm/smmuv3: Get prepared for range invalidation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
HAD is a mandatory features with SMMUv3.1 if S1P is set, which is
our case. Other 3.1 mandatory features come with S2P which we don't
have.
So let's support HAD and advertise SMMUv3.1 support in AIDR.
HAD support allows the CD to disable hierarchical attributes, ie.
if the HAD0/1 bit is set, the APTable field of table descriptors
walked through TTB0/1 is ignored.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the support for AIDR register. It currently advertises
SMMU V3.0 spec.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enhance the smmu_iotlb_inv_iova() helper with range invalidation.
This uses the new fields passed in the NH_VA and NH_VAA commands:
the size of the range, the level and the granule.
As NH_VA and NH_VAA both use those fields, their decoding and
handling is factorized in a new smmuv3_s1_range_inval() helper.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment each entry in the IOTLB corresponds to a page sized
mapping (4K, 16K or 64K), even if the page belongs to a mapped
block. In case of block mapping this unefficiently consumes IOTLB
entries.
Change the value of the entry so that it reflects the actual
mapping it belongs to (block or page start address and size).
Also the level/tg of the entry is encoded in the key. In subsequent
patches we will enable range invalidation. This latter is able
to provide the level/tg of the entry.
Encoding the level/tg directly in the key will allow to invalidate
using g_hash_table_remove() when num_pages equals to 1.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-6-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a specialized SMMUTLBEntry to store the result of
the PTW and cache in the IOTLB. This structure extends the
generic IOMMUTLBEntry struct with the level of the entry and
the granule size.
Those latter will be useful when implementing range invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-5-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the smmu_get_iotlb_key() helper and the
SMMU_IOTLB_ASID() macro. Also move smmu_get_iotlb_key and
smmu_iotlb_key_hash in the IOTLB related code section.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add two helpers: one to lookup for a given IOTLB entry and
one to insert a new entry. We also move the tracing there.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's my first pull request for qemu-5.2, which has quite a few
accumulated things. Highlights are:
* Preliminary support for POWER10 (Power ISA 3.1) instruction emulation
* Add documentation on the (very confusing) pseries NUMA configuration
* Fix some bugs handling edge cases with XICS, XIVE and kernel_irqchip
* Fix icount for a number of POWER registers
* Many cleanups to error handling in XIVE code
* Validate size of -prom-env data
-----BEGIN PGP SIGNATURE-----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=L9Wi
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.2-20200818' into staging
ppc patch queue 2020-08-18
Here's my first pull request for qemu-5.2, which has quite a few
accumulated things. Highlights are:
* Preliminary support for POWER10 (Power ISA 3.1) instruction emulation
* Add documentation on the (very confusing) pseries NUMA configuration
* Fix some bugs handling edge cases with XICS, XIVE and kernel_irqchip
* Fix icount for a number of POWER registers
* Many cleanups to error handling in XIVE code
* Validate size of -prom-env data
# gpg: Signature made Tue 18 Aug 2020 05:18:36 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.2-20200818: (40 commits)
spapr/xive: Use xive_source_esb_len()
nvram: Exit QEMU if NVRAM cannot contain all -prom-env data
spapr/xive: Simplify error handling of kvmppc_xive_cpu_synchronize_state()
ppc/xive: Simplify error handling in xive_tctx_realize()
spapr/xive: Simplify error handling in kvmppc_xive_connect()
ppc/xive: Fix error handling in vmstate_xive_tctx_*() callbacks
spapr/xive: Fix error handling in kvmppc_xive_post_load()
spapr/kvm: Fix error handling in kvmppc_xive_pre_save()
spapr/xive: Rework error handling of kvmppc_xive_set_source_config()
spapr/xive: Rework error handling in kvmppc_xive_get_queues()
spapr/xive: Rework error handling of kvmppc_xive_[gs]et_queue_config()
spapr/xive: Rework error handling of kvmppc_xive_cpu_[gs]et_state()
spapr/xive: Rework error handling of kvmppc_xive_mmap()
spapr/xive: Rework error handling of kvmppc_xive_source_reset()
spapr/xive: Rework error handling of kvmppc_xive_cpu_connect()
spapr: Simplify error handling in spapr_phb_realize()
spapr/xive: Convert KVM device fd checks to assert()
ppc/xive: Introduce dedicated kvm_irqchip_in_kernel() wrappers
ppc/xive: Rework setup of XiveSource::esb_mmio
target/ppc: Integrate icount to purr, vtb, and tbu40
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Convert legacy SD host controller to the SDBus API
- Move legacy API to a separate "sdcard_legacy.h" header
- Introduce methods to access multiple bytes on SDBus data lines
- Fix 'switch function' group location
- Fix SDSC maximum card size (2GB)
CI jobs result:
https://gitlab.com/philmd/qemu/-/pipelines/180605963
-----BEGIN PGP SIGNATURE-----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=Pefc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/sd-next-20200821' into staging
SD/MMC patches
- Convert legacy SD host controller to the SDBus API
- Move legacy API to a separate "sdcard_legacy.h" header
- Introduce methods to access multiple bytes on SDBus data lines
- Fix 'switch function' group location
- Fix SDSC maximum card size (2GB)
CI jobs result:
https://gitlab.com/philmd/qemu/-/pipelines/180605963
# gpg: Signature made Fri 21 Aug 2020 18:27:50 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/sd-next-20200821: (23 commits)
hw/sd: Correct the maximum size of a Standard Capacity SD Memory Card
hw/sd: Fix incorrect populated function switch status data structure
hw/sd: Use sdbus_read_data() instead of sdbus_read_byte() when possible
hw/sd: Add sdbus_read_data() to read multiples bytes on the data line
hw/sd: Use sdbus_write_data() instead of sdbus_write_byte when possible
hw/sd: Add sdbus_write_data() to write multiples bytes on the data line
hw/sd: Rename sdbus_read_data() as sdbus_read_byte()
hw/sd: Rename sdbus_write_data() as sdbus_write_byte()
hw/sd: Rename read/write_data() as read/write_byte()
hw/sd: Move sdcard legacy API to 'hw/sd/sdcard_legacy.h'
hw/sd/sdcard: Make sd_data_ready() static
hw/sd/pl181: Replace disabled fprintf()s by trace events
hw/sd/pl181: Do not create SD card within the SD host controller
hw/sd/pl181: Expose a SDBus and connect the SDCard to it
hw/sd/pl181: Use named GPIOs
hw/sd/pl181: Add TODO to use Fifo32 API
hw/sd/pl181: Rename pl181_send_command() as pl181_do_command()
hw/sd/pl181: Replace fprintf(stderr, "*\n") with error_report()
hw/sd/milkymist: Do not create SD card within the SD host controller
hw/sd/milkymist: Create the SDBus at init()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Once an interrupt has been claimed, but before it has been compelted we
shouldn't receive any more pending interrupts. This patche keeps track
of this to ensure that we don't see any more interrupts until it is
completed.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <394c3f070615ff2b4fab61a1cf9cb48c122913b7.1595655188.git.alistair.francis@wdc.com>
It is enough to simply map the SiFive FU540 L2 cache controller
into the MMIO space using create_unimplemented_device(), with an
FDT fragment generated, to make the latest upstream U-Boot happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1595227748-24720-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a sdbus_read_data() method to read multiple bytes on the
data line of a SD bus.
We might improve the tracing later, for now keep logging each
byte individually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-7-f4bug@amsat.org>
Add a sdbus_write_data() method to write multiple bytes on the
data line of a SD bus.
We might improve the tracing later, for now keep logging each
byte individually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-5-f4bug@amsat.org>
The sdbus_read_data() method do a single byte access on the data
line of a SD bus. Rename it as sdbus_read_byte() and document it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-4-f4bug@amsat.org>
The sdbus_write_data() method do a single byte access on the data
line of a SD bus. Rename it as sdbus_write_byte() and document it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-3-f4bug@amsat.org>
The read/write_data() methods write do a single byte access
on the data line of a SD card. Rename them as read/write_byte().
Add some documentation (not in "hw/sd/sdcard_legacy.h" which we
are going to remove soon).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-2-f4bug@amsat.org>
omap_mmc.c is the last device left using the legacy sdcard API.
Move the prototype declarations into a separate header, to
make it clear this is a legacy API.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180216022933.10945-8-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
sd_data_ready() belongs to the legacy API. As its last user has
been converted to the SDBus API, make it static.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180216022933.10945-7-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :)
The machine/board object is where the SD cards are created.
Since the PXA2xx is not qdevified, for now create the cards
in pxa270_init() which is the SoC model.
In the future we will move this to the board model.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705213350.24725-2-f4bug@amsat.org>
Add 5.2 machine types for arm/i440fx/q35/s390x/spapr.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200819144016.281156-1-cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Since commit 61f20b9dc5 ("spapr_nvram: Pre-initialize the NVRAM to
support the -prom-env parameter"), pseries machines can pre-initialize
the "system" partition in the NVRAM with the data passed to all -prom-env
parameters on the QEMU command line.
In this case it is assumed that all the data fits in 64 KiB, but the user
can easily pass more and crash QEMU:
$ qemu-system-ppc64 -M pseries $(for ((x=0;x<128;x++)); do \
echo -n " -prom-env " ; printf "%0.sx" {1..1024}; \
done) # this requires ~128 Kib
malloc(): corrupted top size
Aborted (core dumped)
This happens because we don't check if all the prom-env data fits in
the NVRAM and chrp_nvram_set_var() happily memcpy() it passed the
buffer.
This crash affects basically all ppc/ppc64 machine types that use -prom-env:
- pseries (all versions)
- g3beige
- mac99
and also sparc/sparc64 machine types:
- LX
- SPARCClassic
- SPARCbook
- SS-10
- SS-20
- SS-4
- SS-5
- SS-600MP
- Voyager
- sun4u
- sun4v
Add a max_len argument to chrp_nvram_create_system_partition() so that
it can check the available size before writing to memory.
Since NVRAM is populated at machine init, it seems reasonable to consider
this error as fatal. So, instead of reporting an error when we detect that
the NVRAM is too small and adapt all machine types to handle it, we simply
exit QEMU in all cases. This is still better than crashing. If someone
wants another behavior, I guess this can be reworked later.
Tested with:
$ yes q | \
(for arch in ppc ppc64 sparc sparc64; do \
echo == $arch ==; \
qemu=${arch}-softmmu/qemu-system-$arch; \
for mach in $($qemu -M help | awk '! /^Supported/ { print $1 }'); do \
echo $mach; \
$qemu -M $mach -monitor stdio -nodefaults -nographic \
$(for ((x=0;x<128;x++)); do \
echo -n " -prom-env " ; printf "%0.sx" {1..1024}; \
done) >/dev/null; \
done; echo; \
done)
Without the patch, affected machine types cause QEMU to report some
memory corruption and crash:
malloc(): corrupted top size
free(): invalid size
*** stack smashing detected ***: terminated
With the patch, QEMU prints the following message and exits:
NVRAM is too small. Try to pass less data to -prom-env
It seems that the conditions for the crash have always existed, but it
affects pseries, the machine type I care for, since commit 61f20b9dc5
only.
Fixes: 61f20b9dc5 ("spapr_nvram: Pre-initialize the NVRAM to support the -prom-env parameter")
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1867739
Reported-by: John Snow <jsnow@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159736033937.350502.12402444542194031035.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that kvmppc_xive_cpu_get_state() returns negative on error, use that
and get rid of the temporary Error object and error_propagate().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707852916.1489912.8376334685349668124.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since kvm_device_access() returns a negative errno on failure, convert
kvmppc_xive_set_source_config() to use it for error checking. This allows
to get rid of the local_err boilerplate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707848764.1489912.17078842252160674523.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since kvm_device_access() returns a negative errno on failure, convert
kvmppc_xive_get_queue_config() and kvmppc_xive_set_queue_config() to
use it for error checking. This allows to get rid of the local_err
boilerplate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707847357.1489912.2032291280645236480.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvm_set_one_reg() returns a negative errno on failure, use that instead
of errno. Also propagate it to callers so they can use it to check
for failures and hopefully get rid of their local_err boilerplate.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707846665.1489912.14267225652103441921.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Use error_setg_errno() instead of error_setg(strerror()). While here,
use -ret instead of errno since kvm_vcpu_enable_cap() returns a negative
errno on failure.
Use ERRP_GUARD() to ensure that errp can be passed to error_append_hint(),
and get rid of the local_err boilerplate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707844549.1489912.4862921680328017645.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Calls to the KVM XIVE device are guarded by kvm_irqchip_in_kernel(). This
ensures that QEMU won't try to use the device if KVM is disabled or if
an in-kernel irqchip isn't required.
When using ic-mode=dual with the pseries machine, we have two possible
interrupt controllers: XIVE and XICS. The kvm_irqchip_in_kernel() helper
will return true as soon as any of the KVM device is created. It might
lure QEMU to think that the other one is also around, while it is not.
This is exactly what happens with ic-mode=dual at machine init when
claiming IRQ numbers, which must be done on all possible IRQ backends,
eg. RTAS event sources or the PHB0 LSI table : only the KVM XICS device
is active but we end up calling kvmppc_xive_source_reset_one() anyway,
which fails. This doesn't cause any trouble because of another bug :
kvmppc_xive_source_reset_one() lacks an error_setg() and callers don't
see the failure.
Most of the other kvmppc_xive_* functions have similar xive->fd
checks to filter out the case when KVM XIVE isn't active. It
might look safer to have idempotent functions but it doesn't
really help to understand what's going on when debugging.
Since we already have all the kvm_irqchip_in_kernel() in place,
also have the callers to check xive->fd as well before calling
KVM XIVE specific code. This is straight-forward for the spapr
specific XIVE code. Some more care is needed for the platform
agnostic XIVE code since it cannot access xive->fd directly.
Introduce new in_kernel() methods in some base XIVE classes
for this purpose and implement them only in spapr.
In all cases, we still need to call kvm_irqchip_in_kernel() so that
compilers can optimize the kvmppc_xive_* calls away when CONFIG_KVM
isn't defined, thus avoiding the need for stubs.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159679993438.876294.7285654331498605426.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Depending on whether XIVE is emultated or backed with a KVM XIVE device,
the ESB MMIOs of a XIVE source point to an I/O memory region or a mapped
memory region.
This is currently handled by checking kvm_irqchip_in_kernel() returns
false in xive_source_realize(). This is a bit awkward as we usually
need to do extra things when we're using the in-kernel backend, not
less. But most important, we can do better: turn the existing "xive.esb"
memory region into a plain container, introduce an "xive.esb-emulated"
I/O subregion and rename the existing "xive.esb" subregion in the KVM
code to "xive.esb-kvm". Since "xive.esb-kvm" is added with overlap
and a higher priority, it prevails over "xive.esb-emulated" (ie.
a guest using KVM XIVE will interact with "xive.esb-kvm" instead of
the default "xive.esb-emulated" region.
While here, consolidate the computation of the MMIO region size in
a common helper.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159679992680.876294.7520540158586170894.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The NVIC provides an outbound qemu_irq "SYSRESETREQ" which it signals
when the guest sets the SYSRESETREQ bit in the AIRCR register. This
matches the hardware design (where the CPU has a signal of this name
and it is up to the SoC to connect that up to an actual reset
mechanism), but in QEMU it mostly results in duplicated code in SoC
objects and bugs where SoC model implementors forget to wire up the
SYSRESETREQ line.
Provide a default behaviour for the case where SYSRESETREQ is not
actually connected to anything: use qemu_system_reset_request() to
perform a system reset. This will allow us to remove the
implementations of SYSRESETREQ handling from the boards where that's
exactly what it does, and also fixes the bugs in the board models
which forgot to wire up the signal:
* microbit
* mps2-an385
* mps2-an505
* mps2-an511
* mps2-an521
* musca-a
* musca-b1
* netduino
* netduinoplus2
We still allow the board to wire up the signal if it needs to, in case
we need to model more complicated reset controller logic or to model
buggy SoC hardware which forgot to wire up the line itself. But
defaulting to "reset the system" is more often going to be correct
than defaulting to "do nothing".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200728103744.6909-3-peter.maydell@linaro.org
Mostly devices don't need to care whether one of their output
qemu_irq lines is connected, because functions like qemu_set_irq()
silently do nothing if there is nothing on the other end. However
sometimes a device might want to implement default behaviour for the
case where the machine hasn't wired the line up to anywhere.
Provide a function qemu_irq_is_connected() that devices can use for
this purpose. (The test is trivial but encapsulating it in a
function makes it easier to see where we're doing it in case we need
to change the implementation later.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200728103744.6909-2-peter.maydell@linaro.org
In legacy mode, virtio_pci_queue_enabled() falls back to
virtio_queue_enabled() to know if the queue is enabled.
But virtio_queue_enabled() calls again virtio_pci_queue_enabled()
if k->queue_enabled is set. This ends in a crash after a stack
overflow.
The problem can be reproduced with
"-device virtio-net-pci,disable-legacy=off,disable-modern=true
-net tap,vhost=on"
And a look to the backtrace is very explicit:
...
#4 0x000000010029a438 in virtio_queue_enabled ()
#5 0x0000000100497a9c in virtio_pci_queue_enabled ()
...
#130902 0x000000010029a460 in virtio_queue_enabled ()
#130903 0x0000000100497a9c in virtio_pci_queue_enabled ()
#130904 0x000000010029a460 in virtio_queue_enabled ()
#130905 0x0000000100454a20 in vhost_net_start ()
...
This patch fixes the problem by introducing a new function
for the legacy case and calls it from virtio_pci_queue_enabled().
It also calls it from virtio_queue_enabled() to avoid code duplication.
Fixes: f19bcdfedd ("virtio-pci: implement queue_enabled method")
Cc: Jason Wang <jasowang@redhat.com>
Cc: Cindy Lu <lulu@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20200727153319.43716-1-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The pci host config register is used to save PCI address for
read/write config data. If guest writes a value to config register,
and then QEMU pauses the vcpu to migrate, after the migration, the guest
will continue to write pci config data, and the write data will be ignored
because of new qemu process losing the config register state.
To trigger the bug:
1. guest is booting in seabios.
2. guest enables the SMRAM in seabios:piix4_apmc_smm_setup, and then
expects to disable the SMRAM by pci_config_writeb.
3. after guest writes the pci host config register, QEMU pauses vcpu
to finish migration.
4. guest write of config data(0x0A) fails to disable the SMRAM because
the config register state is lost.
5. guest continues to boot and crashes in ipxe option ROM due to SMRAM
in enabled state.
Example Reproducer:
step 1. Make modifications to seabios and qemu for increase reproduction
efficiency, write 0xf0 to 0x402 port notify qemu to stop vcpu after
0x0cf8 port wrote i440 configure register. qemu stop vcpu when catch
0x402 port wrote 0xf0.
seabios:/src/hw/pci.c
@@ -52,6 +52,11 @@ void pci_config_writeb(u16 bdf, u32 addr, u8 val)
writeb(mmconfig_addr(bdf, addr), val);
} else {
outl(ioconfig_cmd(bdf, addr), PORT_PCI_CMD);
+ if (bdf == 0 && addr == 0x72 && val == 0xa) {
+ dprintf(1, "stop vcpu\n");
+ outb(0xf0, 0x402); // notify qemu to stop vcpu
+ dprintf(1, "resume vcpu\n");
+ }
outb(val, PORT_PCI_DATA + (addr & 3));
}
}
qemu:hw/char/debugcon.c
@@ -60,6 +61,9 @@ static void debugcon_ioport_write(void *opaque, hwaddr addr, uint64_t val,
printf(" [debugcon: write addr=0x%04" HWADDR_PRIx " val=0x%02" PRIx64 "]\n", addr, val);
#endif
+ if (ch == 0xf0) {
+ vm_stop(RUN_STATE_PAUSED);
+ }
/* XXX this blocks entire thread. Rewrite to use
* qemu_chr_fe_write and background I/O callbacks */
qemu_chr_fe_write_all(&s->chr, &ch, 1);
step 2. start vm1 by the following command line, and then vm stopped.
$ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\
-netdev tap,ifname=tap-test,id=hostnet0,vhost=on,downscript=no,script=no\
-device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\
-device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\
-chardev file,id=seabios,path=/var/log/test.seabios,append=on\
-device isa-debugcon,iobase=0x402,chardev=seabios\
-monitor stdio
step 3. start vm2 to accept vm1 state.
$ qemu-system-x86_64 -machine pc-i440fx-5.0,accel=kvm\
-netdev tap,ifname=tap-test1,id=hostnet0,vhost=on,downscript=no,script=no\
-device virtio-net-pci,netdev=hostnet0,id=net0,bus=pci.0,addr=0x13,bootindex=3\
-device cirrus-vga,id=video0,vgamem_mb=16,bus=pci.0,addr=0x2\
-chardev file,id=seabios,path=/var/log/test.seabios,append=on\
-device isa-debugcon,iobase=0x402,chardev=seabios\
-monitor stdio \
-incoming tcp:127.0.0.1:8000
step 4. execute the following qmp command in vm1 to migrate.
(qemu) migrate tcp:127.0.0.1:8000
step 5. execute the following qmp command in vm2 to resume vcpu.
(qemu) cont
Before this patch, we get KVM "emulation failure" error on vm2.
This patch fixes it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Hogan Wang <hogan.wang@huawei.com>
Message-Id: <20200727084621.3279-1-hogan.wang@huawei.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The main fix is the correction of the goldfish RTC time. On top of that
some small fixes to the recently added vector extensions have been added
(including an assert that fixed a coverity report). There is a change in
the SiFive E debug memory size to match hardware. Finally there is a fix
for PMP accesses.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl8YbM8ACgkQIeENKd+X
cFRusgf+NpstlmK/+35DimtJ9oYV2H+NSE7D9HDEdgm2PszYNDjEiWRMBCl1B2JS
3vTutR198USdcJtdXFrFooaxZaMNf0FQJ7p82BUnNOlUNy7vyFlsRQX687KWJh3+
F0t9MsaBVY3G1UiY6vke2vPdcHNG0cAPUwEWjKIU7E7nBmbvNnZZyXxYGC7yjCBI
GQ1TKqso9wKtvAyc6cNGPcsUUM8P+LI5H+UzQR8A1LZ5bohKIQW+xrdJe6HqGMs1
3xZ4tQS2AG5XaaKz74/AdTJSTf80plG2jDomI9fBoNjqRnyPRAlwgzO88Hc24Bcm
RLzL51UaQv+EddxspAW9gH9FHJRvfA==
=6MUF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200722-1' into staging
This PR contains a few RISC-V fixes.
The main fix is the correction of the goldfish RTC time. On top of that
some small fixes to the recently added vector extensions have been added
(including an assert that fixed a coverity report). There is a change in
the SiFive E debug memory size to match hardware. Finally there is a fix
for PMP accesses.
# gpg: Signature made Wed 22 Jul 2020 17:43:59 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200722-1:
target/riscv: Fix the range of pmpcfg of CSR funcion table
hw/riscv: sifive_e: Correct debug block size
target/riscv: fix vector index load/store constraints
target/riscv: Quiet Coverity complains about vamo*
goldfish_rtc: Fix non-atomic read behaviour of TIME_LOW/TIME_HIGH
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix bug in ACPI which were tripping up guests.
Fix a use-after-free with hotplug of virtio devices.
Block ability to create legacy devices which shouldn't have been
there in the first place.
Fix migration error handling with balloon.
Drop some dead code in virtio.
vtd emulation fixup.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl8YK/4PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpCE4H/1+15xjUiKD0sxnvPdKezbDhtAW0YPY/cHC0
KJRWFDbK/+cl9ZkJQBqUXASV3KWnjSKjQrVph6vtg8huqhhDsnha1JGgamhOa9tC
7rH8RkMA6nUF/su8xnkNyNBfG2lHk6ETyKvvTtuLHzjbkzWd6OYtaQAQJTYI6TVB
aY+MCIT7xfucsL6JaHA8BTccOOjz7pxc6dL4NsQCR3cZkwTtB9JOE5UwgM3IyNP/
DcbFyVUDkXYtlpKU/xO+ZICbxCNsZmHzpnV8KJ07vyJdAhL1hRAayMkNG4xLzW0n
f/ZMlJna5jDP3fRqgVvu8XbY3TcCx1XOBD9ebH5E6hvhWnp8oHI=
=SJjI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi,virtio,pc: bugfixes
Fix bug in ACPI which were tripping up guests.
Fix a use-after-free with hotplug of virtio devices.
Block ability to create legacy devices which shouldn't have been
there in the first place.
Fix migration error handling with balloon.
Drop some dead code in virtio.
vtd emulation fixup.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 22 Jul 2020 13:07:26 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio-pci: Changed vdev to proxy for VirtIO PCI BAR callbacks.
intel_iommu: Use correct shift for 256 bits qi descriptor
virtio: verify that legacy support is not accidentally on
virtio: list legacy-capable devices
virtio-balloon: Replace free page hinting references to 'report' with 'hint'
virtio-balloon: Add locking to prevent possible race when starting hinting
virtio-balloon: Prevent guest from starting a report when we didn't request one
virtio: Drop broken and superfluous object_property_set_link()
acpi: accept byte and word access to core ACPI registers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The specification says:
0x00 TIME_LOW R: Get current time, then return low-order 32-bits.
0x04 TIME_HIGH R: Return high 32-bits from previous TIME_LOW read.
...
To read the value, the kernel must perform an IO_READ(TIME_LOW),
which returns an unsigned 32-bit value, before an IO_READ(TIME_HIGH),
which returns a signed 32-bit value, corresponding to the higher half
of the full value.
However, we were just returning the current time for both. If the guest
is unlucky enough to read TIME_LOW and TIME_HIGH either side of an
overflow of the lower half, it will see time be in the future, before
jumping backwards on the next read, and Linux currently relies on the
atomicity guaranteed by the spec so is affected by this. Fix this
violation of the spec by caching the correct value for TIME_HIGH
whenever TIME_LOW is read, and returning that value for any TIME_HIGH
read.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200718004934.83174-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Several types of virtio devices had already been around before the
virtio standard was specified. These devices support virtio in legacy
(and transitional) mode.
Devices that have been added in the virtio standard are considered
non-transitional (i.e. with no support for legacy virtio).
Provide a helper function so virtio transports can figure that out
easily.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200707105446.677966-2-cohuck@redhat.com>
Cc: qemu-stable@nongnu.org
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Recently a feature named Free Page Reporting was added to the virtio
balloon. In order to avoid any confusion we should drop the use of the word
'report' when referring to Free Page Hinting. So what this patch does is go
through and replace all instances of 'report' with 'hint" when we are
referring to free page hinting.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Message-Id: <20200720175128.21935.93927.stgit@localhost.localdomain>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commits b6d7e9b66f..a43770df5d simplified the error propagation.
Similarly to commit 6fd5bef10b "qom: Make functions taking Error**
return bool, not void", let fw_cfg_add_from_generator() return a
boolean value, not void.
This allow to simplify parse_fw_cfg() and fixes the error handling
issue reported by Coverity (CID 1430396):
In parse_fw_cfg():
Variable assigned once to a constant guards dead code.
Local variable local_err is assigned only once, to a constant
value, making it effectively constant throughout its scope.
If this is not the intent, examine the logic to see if there
is a missing assignment that would make local_err not remain
constant.
It's the call of fw_cfg_add_from_generator():
Error *local_err = NULL;
fw_cfg_add_from_generator(fw_cfg, name, gen_id, errp);
if (local_err) {
error_propagate(errp, local_err);
return -1;
}
return 0;
If it fails, parse_fw_cfg() sets an error and returns 0, which is
wrong. Harmless, because the only caller passes &error_fatal.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: Coverity CID 1430396: 'Constant' variable guards dead code (DEADCODE)
Fixes: 6552d87c48 ("softmmu/vl: Let -fw_cfg option take a 'gen_id' argument")
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200721131911.27380-3-philmd@redhat.com>
Document FWCfgDataGeneratorClass::get_data() return NULL
on error, and non-NULL on success. This allow us to simplify
fw_cfg_add_from_generator(). Since we don't need a local
variable to propagate the error, we can remove the ERRP_GUARD()
macro.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200721131911.27380-2-philmd@redhat.com>
Add documentation comments for the various qdev functions
related to creating and connecting GPIO lines.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200711142425.16283-4-peter.maydell@linaro.org
Add a doc comment for qdev_unrealize(), to go with the new
documentation for the realize part of the qdev lifecycle.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200711142425.16283-3-peter.maydell@linaro.org
The doc-comments which document the qdev API are split between the
header file and the C source files, because as a project we haven't
been consistent about where we put them.
Move all the doc-comments in qdev.c to the header files, so that
users of the APIs don't have to look at the implementation files for
this information.
In the process, unify them into our doc-comment format and expand on
them in some cases to clarify expected use cases.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200711142425.16283-2-peter.maydell@linaro.org
Control this cpu feature via a machine property, much as we do
with secure=on, since both require specialized support in the
machine setup to be functional.
Default MTE to off, since this feature implies extra overhead.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here are some assorted fixes for qemu-5.1:
* SLOF update with improved TPM handling, and fix for possible stack
overflows on many-vcpu machines
* Fix for NUMA distances on NVLink2 attached GPU memory nodes
* Fixes to fail more gracefully on attempting to plug unsupported PCI bridge types
* Don't allow pnv-psi device to be user created
-----BEGIN PGP SIGNATURE-----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=CYAQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.1-20200720' into staging
ppc patch queue 20200720
Here are some assorted fixes for qemu-5.1:
* SLOF update with improved TPM handling, and fix for possible stack
overflows on many-vcpu machines
* Fix for NUMA distances on NVLink2 attached GPU memory nodes
* Fixes to fail more gracefully on attempting to plug unsupported PCI bridge types
* Don't allow pnv-psi device to be user created
# gpg: Signature made Mon 20 Jul 2020 06:29:21 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.1-20200720:
pseries: Update SLOF firmware image
spapr: Add a new level of NUMA for GPUs
spapr_pci: Robustify support of PCI bridges
ppc/pnv: Make PSI device types not user creatable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
NUMA nodes corresponding to GPU memory currently have the same
affinity/distance as normal memory nodes. Add a third NUMA associativity
reference point enabling us to give GPU nodes more distance.
This is guest visible information, which shouldn't change under a
running guest across migration between different qemu versions, so make
the change effective only in new (pseries > 5.0) machine types.
Before, `numactl -H` output in a guest with 4 GPUs (nodes 2-5):
node distances:
node 0 1 2 3 4 5
0: 10 40 40 40 40 40
1: 40 10 40 40 40 40
2: 40 40 10 40 40 40
3: 40 40 40 10 40 40
4: 40 40 40 40 10 40
5: 40 40 40 40 40 10
After:
node distances:
node 0 1 2 3 4 5
0: 10 40 80 80 80 80
1: 40 10 80 80 80 80
2: 80 80 10 80 80 80
3: 80 80 80 10 80 80
4: 80 80 80 80 10 80
5: 80 80 80 80 80 10
These are the same distances as on the host, mirroring the change made
to host firmware in skiboot commit f845a648b8cb ("numa/associativity:
Add a new level of NUMA for GPU's").
Signed-off-by: Reza Arbab <arbab@linux.ibm.com>
Message-Id: <20200716225655.24289-1-arbab@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In commit d88c42ff2c we added new prototype but neglected to
add their documentation. Fix that.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-6-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "create_simple" names for functions that allocate, initialize,
configure and realize device objects: pci_create_simple(),
isa_create_simple(), usb_create_simple(). For consistency, rename
i2c_create_slave() as i2c_slave_create_simple(). Since we have
to update all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-5-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The other i2c functions are called i2c_slave_FOO(). Rename as
i2c_slave_realize_and_unref() to be consistent.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-4-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "new" names for functions that allocate and initialize
device objects: pci_new(), isa_new(), usb_new().
Let's call this one i2c_slave_new(). Since we have to update
all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-3-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
All the callers of aspeed_i2c_get_bus() have a AspeedI2CState and
cast it to a DeviceState with DEVICE(), then aspeed_i2c_get_bus()
cast the DeviceState to an AspeedI2CState with ASPEED_I2C()...
Simplify aspeed_i2c_get_bus() callers by using AspeedI2CState
argument.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-2-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Any write to a device might cause a re-arrangement of memory
triggering a TLB flush and potential re-size of the TLB invalidating
previous entries. This would cause users of qemu_plugin_get_hwaddr()
to see the warning:
invalid use of qemu_plugin_get_hwaddr
because of the failed tlb_lookup which should always succeed. To
prevent this we save the IOTLB data in case it is later needed by a
plugin doing a lookup.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200713200415.26214-7-alex.bennee@linaro.org>
Conver the Ibex UART to use the recently added qdev-clock functions.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: b0136fad870a29049959ec161c1217b967d7e19d.1594332223.git.alistair.francis@wdc.com
Message-Id: <b0136fad870a29049959ec161c1217b967d7e19d.1594332223.git.alistair.francis@wdc.com>
OpenSBI is the default firmware in Qemu and has various firmware loading
options. Currently, qemu loader uses fw_jump which has a compile time
pre-defined address where fdt & kernel image must reside. This puts a
constraint on image size of the Linux kernel depending on the fdt location
and available memory. However, fw_dynamic allows the loader to specify
the next stage location (i.e. Linux kernel/U-Boot) in memory and other
configurable boot options available in OpenSBI.
Add support for OpenSBI dynamic firmware loading support. This doesn't
break existing setup and fw_jump will continue to work as it is. Any
other firmware will continue to work without any issues as long as it
doesn't expect anything specific from loader in "a2" register.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-4-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, the fdt is copied to the ROM after the reset vector. The firmware
has to copy it to DRAM. Instead of this, directly copy the device tree to a
pre-computed dram address. The device tree load address should be as far as
possible from kernel and initrd images. That's why it is kept at the end of
the DRAM or 4GB whichever is lesser.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-3-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, all riscv machines except sifive_u have identical reset vector
code implementations with memory addresses being different for all machines.
They can be easily combined into a single function in common code.
Move it to common function and let all the machines use the common function.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-2-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 'cpu_type' has been moved from BCM283XState to BCM283XClass
in commit 210f47840d, but we forgot to remove the old variable.
Do it now.
Fixes: 210f47840d ("hw/arm/bcm2836: Hardcode correct CPU type")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200703200459.23294-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Michael started to work on the AVR port few years ago [*] and kept
improving the code over various series.
List of people who help him (in chronological order):
- Richard Henderson
- Sarah Harris and Edward Robbins
- Philippe Mathieu-Daudé and Aleksandar Markovic
- Pavel Dovgalyuk
- Thomas Huth
[*] The oldest contribution I could find on the list is from 2016:
https://lists.nongnu.org/archive/html/qemu-devel/2016-06/msg02985.html
Tests included:
$ avocado --show=app run -t arch:avr tests/acceptance/
Fetching asset from tests/acceptance/machine_avr6.py:AVR6Machine.test_freertos
(1/1) tests/acceptance/machine_avr6.py:AVR6Machine.test_freertos: PASS (2.13 s)
RESULTS : PASS 1 | ERROR 0 | FAIL 0 | SKIP 0 | WARN 0 | INTERRUPT 0 | CANCEL 0
JOB TIME : 2.35 s
$ make check-qtest-avr
TEST check-qtest-avr: tests/qtest/boot-serial-test
TEST check-qtest-avr: tests/qtest/cdrom-test
TEST check-qtest-avr: tests/qtest/device-introspect-test
TEST check-qtest-avr: tests/qtest/machine-none-test
TEST check-qtest-avr: tests/qtest/qmp-test
TEST check-qtest-avr: tests/qtest/qmp-cmd-test
TEST check-qtest-avr: tests/qtest/qom-test
TEST check-qtest-avr: tests/qtest/test-hmp
TEST check-qtest-avr: tests/qtest/qos-test
CI results:
. https://cirrus-ci.com/build/5697049146425344
. https://gitlab.com/philmd/qemu/-/pipelines/165328058
. https://travis-ci.org/github/philmd/qemu/builds/705817933
. https://app.shippable.com/github/philmd/qemu/runs/822/summary/console
-----BEGIN PGP SIGNATURE-----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=gFE5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/avr-port-20200711' into staging
8bit AVR port from Michael Rolnik.
Michael started to work on the AVR port few years ago [*] and kept
improving the code over various series.
List of people who help him (in chronological order):
- Richard Henderson
- Sarah Harris and Edward Robbins
- Philippe Mathieu-Daudé and Aleksandar Markovic
- Pavel Dovgalyuk
- Thomas Huth
[*] The oldest contribution I could find on the list is from 2016:
https://lists.nongnu.org/archive/html/qemu-devel/2016-06/msg02985.html
Tests included:
$ avocado --show=app run -t arch:avr tests/acceptance/
Fetching asset from tests/acceptance/machine_avr6.py:AVR6Machine.test_freertos
(1/1) tests/acceptance/machine_avr6.py:AVR6Machine.test_freertos: PASS (2.13 s)
RESULTS : PASS 1 | ERROR 0 | FAIL 0 | SKIP 0 | WARN 0 | INTERRUPT 0 | CANCEL 0
JOB TIME : 2.35 s
$ make check-qtest-avr
TEST check-qtest-avr: tests/qtest/boot-serial-test
TEST check-qtest-avr: tests/qtest/cdrom-test
TEST check-qtest-avr: tests/qtest/device-introspect-test
TEST check-qtest-avr: tests/qtest/machine-none-test
TEST check-qtest-avr: tests/qtest/qmp-test
TEST check-qtest-avr: tests/qtest/qmp-cmd-test
TEST check-qtest-avr: tests/qtest/qom-test
TEST check-qtest-avr: tests/qtest/test-hmp
TEST check-qtest-avr: tests/qtest/qos-test
CI results:
. https://cirrus-ci.com/build/5697049146425344
. https://gitlab.com/philmd/qemu/-/pipelines/165328058
. https://travis-ci.org/github/philmd/qemu/builds/705817933
. https://app.shippable.com/github/philmd/qemu/runs/822/summary/console
# gpg: Signature made Sat 11 Jul 2020 10:03:11 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/avr-port-20200711: (32 commits)
target/avr/disas: Fix store instructions display order
target/avr/cpu: Fix $PC displayed address
target/avr/cpu: Drop tlb_flush() in avr_cpu_reset()
target/avr: Add section into QEMU documentation
tests/acceptance: Test the Arduino MEGA2560 board
tests/boot-serial: Test some Arduino boards (AVR based)
hw/avr: Add limited support for some Arduino boards
hw/avr: Add some ATmega microcontrollers
hw/avr: Add support for loading ELF/raw binaries
hw/misc: avr: Add limited support for power reduction device
hw/timer: avr: Add limited support for 16-bit timer peripheral
hw/char: avr: Add limited support for USART peripheral
tests/machine-none: Add AVR support
target/avr: Register AVR support with the rest of QEMU
target/avr: Add support for disassembling via option '-d in_asm'
target/avr: Initialize TCG register variables
target/avr: Add instruction translation - CPU main translation function
target/avr: Add instruction translation - MCU Control Instructions
target/avr: Add instruction translation - Bit and Bit-test Instructions
target/avr: Add instruction translation - Data Transfer Instructions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a simple device of just one register, and whenever this
register is written to it calls qemu_set_irq function for each
of 8 bits/IRQs. It is used to implement AVR Power Reduction.
[AM: Remove word 'Atmel' from filenames and all elements of code]
Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[rth: Squash include fix and file rename from f4bug]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200705140315.260514-22-huth@tuxfamily.org>
These were designed to facilitate testing but should provide enough
function to be useful in other contexts. Only a subset of the functions
of each peripheral is implemented, mainly due to the lack of a standard
way to handle electrical connections (like GPIO pins).
[AM: Remove word 'Atmel' from filenames and all elements of code]
Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Sarah Harris <S.E.Harris@kent.ac.uk>
Signed-off-by: Ed Robbins <E.J.C.Robbins@kent.ac.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[rth: Squash info mtree fixes and a file rename from f4bug]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMD: Use qemu_log_mask(LOG_UNIMP), replace goto by return]
Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200705140315.260514-21-huth@tuxfamily.org>
[PMD: Check cpu-frequency-hz property in realize()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These were designed to facilitate testing but should provide enough
function to be useful in other contexts. Only a subset of the functions
of each peripheral is implemented, mainly due to the lack of a standard
way to handle electrical connections (like GPIO pins).
[AM: Remove word 'Atmel' from filenames and all elements of code]
Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Sarah Harris <S.E.Harris@kent.ac.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[rth: Squash I/O size fix and file rename from f4bug]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Reviewed-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200705140315.260514-20-huth@tuxfamily.org>
This is helpful when debugging stuck guest timers.
As we need apic_get_current_count for that, and it is really not
emulation specific, move it to apic_common.c and export it. Fix its
style at this chance as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <e00e2896-ca5b-a929-de7a-8e5762f0c1c2@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
move the vcpu throttling functionality into its own module.
This functionality is not specific to any accelerator,
and it is used currently by migration to slow down guests to try to
have migrations converge, and by the cocoa MacOS UI to throttle speed.
cpu-throttle contains the controls to adjust and inspect throttle
settings, start (set) and stop vcpu throttling, and the throttling
function itself that is run periodically on vcpus to make them take a nap.
Execution of the throttling function on all vcpus is triggered by a timer,
registered at module initialization.
No functionality change.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20200629093504.3228-3-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
See recent commit "error: Document Error API usage rules" for
rationale.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-32-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The generic pc_machine_initfn() calls pc_system_flash_create() which creates
'system.flash0' and 'system.flash1' devices. These devices are then realized
by pc_system_flash_map() which is called from pc_system_firmware_init() which
itself is called via pc_memory_init(). The latter however is not called when
xen_enable() is true and hence the following assertion fails:
qemu-system-i386: hw/core/qdev.c:439: qdev_assert_realized_properly:
Assertion `dev->realized' failed
These flash devices are unneeded when using Xen so this patch avoids the
assertion by simply removing them using pc_system_flash_cleanup_unused().
Reported-by: Jason Andryuk <jandryuk@gmail.com>
Fixes: ebc29e1bea ("pc: Support firmware configuration with -blockdev")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200624121841.17971-3-paul@xen.org>
Fixes: dfe8c79c44 ("qdev: Assert onboard devices all get realized properly")
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
- add the tls-cipher-suites object,
- add the ability to QOM objects to produce data consumable
by the fw_cfg device,
- let the tls-cipher-suites object implement the
FW_CFG_DATA_GENERATOR interface.
This is required by EDK2 'HTTPS Boot' feature of OVMF to tell
the guest which TLS ciphers it can use.
CI jobs results:
https://travis-ci.org/github/philmd/qemu/builds/704724619https://gitlab.com/philmd/qemu/-/pipelines/162938106https://cirrus-ci.com/build/4682977303068672
-----BEGIN PGP SIGNATURE-----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=QArU
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/fw_cfg-20200704' into staging
firmware (and crypto) patches
- add the tls-cipher-suites object,
- add the ability to QOM objects to produce data consumable
by the fw_cfg device,
- let the tls-cipher-suites object implement the
FW_CFG_DATA_GENERATOR interface.
This is required by EDK2 'HTTPS Boot' feature of OVMF to tell
the guest which TLS ciphers it can use.
CI jobs results:
https://travis-ci.org/github/philmd/qemu/builds/704724619https://gitlab.com/philmd/qemu/-/pipelines/162938106https://cirrus-ci.com/build/4682977303068672
# gpg: Signature made Sat 04 Jul 2020 17:37:08 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/fw_cfg-20200704:
crypto/tls-cipher-suites: Produce fw_cfg consumable blob
softmmu/vl: Allow -fw_cfg 'gen_id' option to use the 'etc/' namespace
softmmu/vl: Let -fw_cfg option take a 'gen_id' argument
hw/nvram/fw_cfg: Add the FW_CFG_DATA_GENERATOR interface
crypto: Add tls-cipher-suites object
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently we have 2 types of vhost backends in QEMU: vhost kernel and
vhost-user. The above patch provides a generic device for vDPA purpose,
this vDPA device exposes to user space a non-vendor-specific configuration
interface for setting up a vhost HW accelerator, this patch set introduces
a third vhost backend called vhost-vdpa based on the vDPA interface.
Vhost-vdpa usage:
qemu-system-x86_64 -cpu host -enable-kvm \
......
-netdev type=vhost-vdpa,vhostdev=/dev/vhost-vdpa-id,id=vhost-vdpa0 \
-device virtio-net-pci,netdev=vhost-vdpa0,page-per-vq=on \
Signed-off-by: Lingshan zhu <lingshan.zhu@intel.com>
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Cindy Lu <lulu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200701145538.22333-14-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Doug Evans