The current semihost exception number (16) is a reserved number (range
[16-17]). The upcoming double trap specification uses that number for
the double trap exception. Since the privileged spec (Table 22) defines
ranges for custom uses change the semihosting exception number to 63
which belongs to the range [48-63] in order to avoid any future
collisions with reserved exception.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240422135840.1959967-1-cleger@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use qemu_fdt_setprop_u64() instead of qemu_fdt_setprop_cell()
to set the address of initrd in FDT to support 64-bit address.
Signed-off-by: Cheng Yang <yangcheng.work@foxmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <tencent_A4482251DD0890F312758FA6B33F60815609@qq.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SBI defines a Debug Console extension "DBCN" that will, in time, replace
the legacy console putchar and getchar SBI extensions.
The appeal of the DBCN extension is that it allows multiple bytes to be
read/written in the SBI console in a single SBI call.
As far as KVM goes, the DBCN calls are forwarded by an in-kernel KVM
module to userspace. But this will only happens if the KVM module
actually supports this SBI extension and we activate it.
We'll check for DBCN support during init time, checking if get-reg-list
is advertising KVM_RISCV_SBI_EXT_DBCN. In that case, we'll enable it via
kvm_set_one_reg() during kvm_arch_init_vcpu().
Finally, change kvm_riscv_handle_sbi() to handle the incoming calls for
SBI_EXT_DBCN, reading and writing as required.
A simple KVM guest with 'earlycon=sbi', running in an emulated RISC-V
host, takes around 20 seconds to boot without using DBCN. With this
patch we're taking around 14 seconds to boot due to the speed-up in the
terminal output. There's no change in boot time if the guest isn't
using earlycon.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240425155012.581366-1-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Implementing wrs.nto to always just return is consistent with the
specification, as the instruction is permitted to terminate the
stall for any reason, but it's not useful for virtualization, where
we'd like the guest to trap to the hypervisor in order to allow
scheduling of the lock holding VCPU. Change to always immediately
raise exceptions when the appropriate conditions are present,
otherwise continue to just return. Note, immediately raising
exceptions is also consistent with the specification since the
time limit that should expire prior to the exception is
implementation-specific.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Christoph Müllner <christoph.muellner@vrull.eu>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240424142808.62936-2-ajones@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Zkr extension may only be exposed to KVM guests if the VMM
implements the SEED CSR. Use the same implementation as TCG.
Without this patch, running with a KVM which does not forward the
SEED CSR access to QEMU will result in an ILL exception being
injected into the guest (this results in Linux guests crashing on
boot). And, when running with a KVM which does forward the access,
QEMU will crash, since QEMU doesn't know what to do with the exit.
Fixes: 3108e2f1c6 ("target/riscv/kvm: update KVM exts to Linux 6.8")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Cc: qemu-stable <qemu-stable@nongnu.org>
Message-ID: <20240422134605.534207-2-ajones@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since only root APLICs can have hw IRQ lines, aplic->parent should
be initialized first.
Fixes: e8f79343cf ("hw/intc: Add RISC-V AIA APLIC device emulation")
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: yang.zhang <yang.zhang@hexintek.com>
Cc: qemu-stable <qemu-stable@nongnu.org>
Message-ID: <20240409014445.278-1-gaoshanliukou@163.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
* hw/intc/arm_gic: Fix set pending of PPIs
* hw/intc/arm_gic: Fix writes to GICD_ITARGETSRn
* xilinx_zynq: Add cache controller
* xilinx_zynq: Support up to two CPU cores
* tests/avocado: update sbsa-ref firmware
* sbsa-ref: move to Neoverse-N2 as default
* More decodetree conversion of A64 ASIMD insns
* docs/system/target-arm: Re-alphabetize board list
* Implement FEAT WFxT and enable for '-cpu max'
* hw/usb/hcd-ohci: Fix#1510, #303: pid not IN or OUT
-----BEGIN PGP SIGNATURE-----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=Jy5P
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20240531' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm:
* hw/intc/arm_gic: Fix set pending of PPIs
* hw/intc/arm_gic: Fix writes to GICD_ITARGETSRn
* xilinx_zynq: Add cache controller
* xilinx_zynq: Support up to two CPU cores
* tests/avocado: update sbsa-ref firmware
* sbsa-ref: move to Neoverse-N2 as default
* More decodetree conversion of A64 ASIMD insns
* docs/system/target-arm: Re-alphabetize board list
* Implement FEAT WFxT and enable for '-cpu max'
* hw/usb/hcd-ohci: Fix#1510, #303: pid not IN or OUT
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmZZvHgZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3uArEACZgk0hqKtRcEzwdJi7w7ax
# ta/Iyl7AA+ngmh0qcE8QX8rzZhcGcKhsaQ8dNESMIBqVi1fS0hmNrIUWhXqmvNmZ
# 07WJvQx7Ki9YNX02frjkRZTwWozsbW8uoaXgnngFK93PNh/IoQBRP5T/LIZ5t3d7
# 7I/O/tnS/LZrL6wtP4EbRIEvZ4dfJe3X+uSCHSF8iOYrJLrZCsy/ItJqzY6Y0f96
# iUoOfXjrYH2hM9VkJGHIGy1r9nYRkCxXREQh7ahw/z6mv0nIB1YTS1eR0dH9D1yM
# afdby8iPN7k+f3en+2dHfyPjani4vPd1/k9mgLnQtVLOHrdw2APs1Q59YwYhunhe
# ZC0Fcp6jBSkcI6LHRY0bRtY0U3SBPrfkSD5sJrNH1obnsSvizeSU3uCq1QmKRCRY
# FuARmE77ywY8CURiqfwPSrC/ecSnamueIQNKNPZVQ5ve3dbokp/Gr1eJgcq80ovK
# wIKmNhJq60qBcj2zQ1aw1PP3+zvbZ/rl2j0abGbxBH3Kkp9AvALDiLRMciazVWph
# vbx7e1Y90Zrs3ap1AAUFUyWexYPNvZWmSGOaWv6Wdt+1Yf/YDW9wrwjVd3eRG9rM
# vgNMrccysBUNDpS4s0KSbqLy9AsjqAa41SiKipWFBekUyQFboNpTNfDNCspIPj9m
# dnI4fyXkVmSCYFiW2akmjg==
# =Jy5P
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 31 May 2024 05:03:04 AM PDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
* tag 'pull-target-arm-20240531' of https://git.linaro.org/people/pmaydell/qemu-arm: (43 commits)
hw/usb/hcd-ohci: Fix#1510, #303: pid not IN or OUT
target/arm: Implement FEAT WFxT and enable for '-cpu max'
accel/tcg: Make TCGCPUOps::cpu_exec_halt return bool for whether to halt
docs/system/target-arm: Re-alphabetize board list
target/arm: Disable SVE extensions when SVE is disabled
target/arm: Convert FCSEL to decodetree
target/arm: Convert FMADD, FMSUB, FNMADD, FNMSUB to decodetree
target/arm: Convert SQDMULH, SQRDMULH to decodetree
target/arm: Tidy SQDMULH, SQRDMULH (vector)
target/arm: Convert MLA, MLS to decodetree
target/arm: Convert MUL, PMUL to decodetree
target/arm: Convert SABA, SABD, UABA, UABD to decodetree
target/arm: Convert SMAX, SMIN, UMAX, UMIN to decodetree
target/arm: Convert SRHADD, URHADD to decodetree
target/arm: Convert SRHADD, URHADD to gvec
target/arm: Convert SHSUB, UHSUB to decodetree
target/arm: Convert SHSUB, UHSUB to gvec
target/arm: Convert SHADD, UHADD to decodetree
target/arm: Convert SHADD, UHADD to gvec
target/arm: Use TCG_COND_TSTNE in gen_cmtst_vec
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
FEAT_WFxT introduces new instructions WFIT and WFET, which are like
the existing WFI and WFE but allow the guest to pass a timeout value
in a register. The instructions will wait for an interrupt/event as
usual, but will also stop waiting when the value of CNTVCT_EL0 is
greater than or equal to the specified timeout value.
We implement WFIT by setting up a timer to expire at the right
point; when the timer expires it sets the EXITTB interrupt, which
will cause the CPU to leave the halted state. If we come out of
halt for some other reason, we unset the pending timer.
We implement WFET as a nop, which is architecturally permitted and
matches the way we currently make WFE a nop.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240430140035.3889879-3-peter.maydell@linaro.org
The TCGCPUOps::cpu_exec_halt method is called from cpu_handle_halt()
when the CPU is halted, so that a target CPU emulation can do
anything target-specific it needs to do. (At the moment we only use
this on i386.)
The current specification of the method doesn't allow the target
specific code to do something different if the CPU is about to come
out of the halt state, because cpu_handle_halt() only determines this
after the method has returned. (If the method called cpu_has_work()
itself this would introduce a potential race if an interrupt arrived
between the target's method implementation checking and
cpu_handle_halt() repeating the check.)
Change the definition of the method so that it returns a bool to
tell cpu_handle_halt() whether to stay in halt or not.
We will want this for the Arm target, where FEAT_WFxT wants to do
some work only for the case where the CPU is in halt but about to
leave it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240430140035.3889879-2-peter.maydell@linaro.org
The board list in target-arm.rst is supposed to be in alphabetical
order by the title text of each file (which is not the same as
alphabetical order by filename). A few items had got out of order;
correct them.
The entry for
"Facebook Yosemite v3.5 Platform and CraterLake Server (fby35)"
remains out-of-order, because this is not its own file
but is currently part of the aspeed.rst file.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240520141421.1895138-1-peter.maydell@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-34-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are the only instructions in the 3 source scalar class.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240528203044.612851-33-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are the last instructions within disas_simd_three_reg_same
and disas_simd_scalar_three_reg_same, so remove them.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240528203044.612851-32-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already have a gvec helper for the operations, but we aren't
using it on the aa32 neon side. Create a unified expander for
use by both aa32 and aa64 translators.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-31-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-30-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-29-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-28-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-27-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-26-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-24-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-23-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-22-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-21-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-20-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-18-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-17-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-16-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-14-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240528203044.612851-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240528203044.612851-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are faux 2-operand instructions, reading from rd.
Sort them next to the other three-operand same insns for clarity.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This eliminates the last uses of these neon helpers.
Incorporate the MO_64 expanders as an option to the vector expander.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This eliminates the last uses of these neon helpers.
Incorporate the MO_64 expanders as an option to the vector expander.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240528203044.612851-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No need for a full comparison; xor produces non-zero bits
for QC just fine.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240528203044.612851-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Moving to Neoverse-N2 gives us several cpu features to use for expanding
our platform:
- branch target identification
- pointer authentication
- RME for confidential computing
- RNG for EFI_PROTOCOL_RNG
- SVE being enabled by default
We do not go for "max" as default to have stable set of features enabled
by default. It is still supported and can be selected with "--cpu"
argument.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20240523165353.6547-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Partial support for NUMA setup:
- cpu nodes
- memory nodes
Used versions:
- Trusted Firmware v2.11.0
- Tianocore EDK2 stable202405
- Tianocore EDK2 Platforms code commit 4bbd0ed
Firmware is built using Debian 'bookworm' cross toolchain (gcc 12.2.0).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Zynq 7000 SoCs contain two Arm Cortex-A9 MPCore (the Zynq 7000S have only
one core). Add support for up to two simulated cores.
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Message-id: 20240524120837.10057-3-sebastian.huber@embedded-brains.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: removed unnecessary double-cast]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Zynq 7000 SoCs contain a CoreLink L2C-310 cache controller. Add the
corresponding Qemu device to the xilinx-zynq-a9 machine.
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Message-id: 20240524120837.10057-2-sebastian.huber@embedded-brains.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to the GICv2 specification section 4.3.12, "Interrupt Processor
Targets Registers, GICD_ITARGETSRn":
"Any change to a CPU targets field value:
[...]
* Has an effect on any pending interrupts. This means:
- adding a CPU interface to the target list of a pending interrupt makes that
interrupt pending on that CPU interface
- removing a CPU interface from the target list of a pending interrupt
removes the pending state of that interrupt on that CPU interface."
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Message-id: 20240524113256.8102-3-sebastian.huber@embedded-brains.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to the GICv2 specification section 4.3.7, "Interrupt Set-Pending
Registers, GICD_ISPENDRn":
"In a multiprocessor implementation, GICD_ISPENDR0 is banked for each connected
processor. This register holds the Set-pending bits for interrupts 0-31."
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Message-id: 20240524113256.8102-2-sebastian.huber@embedded-brains.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clément Léger