The H_GUEST_RUN_VCPU hcall is used to start execution of a Guest VCPU.
The Hypervisor will update the state of the Guest VCPU based on the
input buffer, restore the saved Guest VCPU state, and start its
execution.
The Guest VCPU can stop running for numerous reasons including HCALLs,
hypervisor exceptions, or an outstanding Host Partition Interrupt.
The reason that the Guest VCPU stopped running is communicated through
R4 and the output buffer will be filled in with any relevant state.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Currently, nested_ppc_state stores a certain set of registers and works
with nested_[load|save]_state() for state transfer as reqd for nested-hv API.
Extending these with additional registers state as reqd for nested PAPR API.
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
These wrappers call out to handle POWER7 and newer in separate
functions but reduce to the generic case when TARGET_PPC64 is not
defined. It is easy enough to include the switch in the beginning of
the generic functions to branch out to the specific functions and get
rid of these wrappers. This avoids one indirection and entirely
compiles out the switch without TARGET_PPC64.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Concatenate #if blocks that are ending then beginning on the next line
again.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Remove check for !defined(CONFIG_USER_ONLY) as this is already within
an #ifndef CONFIG_USER_ONLY block.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Use #ifdef, #ifndef for brevity and add comments to #endif that are
more than a few lines apart for clarity.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Add gen_exception_err_nip() that does the same as gen_exception_err()
but takes the nip as a parameter to allow specifying it instead of
using the current instruction address then change gen_exception_err()
to use it.
The gen_exception() and gen_exception_nip() functions are similar so
remove code duplication from those too while at it.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Improve readability by shortening some long comments, removing
comments that state the obvious and dropping some empty lines so they
don't distract when reading the code.
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Use the env_cpu function to get the CPUState for cpu_abort. These are
only needed in case of fatal errors so this allows to avoid casting
and storing CPUState in a local variable wnen not needed.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Big (SMT8) cores have a complicated function to map the core, thread ID
to pervasive topology (PIR). Fix this for power8, power9, and power10.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Currently in tcg mode, when reading from power10 pmu spr like MMCR3,
qemu logs this message (when starting qemu with -d guest_errors)
Trying to read invalid spr 754 (0x2f2) at 0000000030056bb0
This is becuase, no read/write call-backs are registered for
these SPRs. Add support to register generic read/write
functions to these power10 pmu sprs to fix it.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This patch moves the below instructions to decodetree specification:
{add, subf}[c,e,me,ze][o][.] : XO-form
addic[.], subfic : D-form
addex : Z23-form
This patch introduces XO form instructions into decode tree
specification, for which all the four variations([o][.]) have been
handled with a single pattern. The changes were verified by validating
that the tcg ops generated by those instructions remain the same, which
were captured with the '-d in_asm,op' flag.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Chinmay Rath <rathc@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER10 hardware implements a degenerate transactional memory facility
in POWER8/9 PCR compatibility modes to permit migration from older
CPUs, but POWER10 / ISA v3.1 mode does not support it so the CPU model
should not support it.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The POWER9 DD1 and POWER10 DD1 chips are not public and are no longer of
any use in QEMU. Remove them.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Prevent guest state modifying the MSR[ME] bit. Per ISA:
An attempt to modify MSR[ME] in privileged but non-hypervisor state
is ignored (i.e., the bit is not changed).
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Fix an off by one bug.
Fixes: 1b53948ff8 ("target/ppc: Use GDBFeature for dynamic XML")
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
query-cpu-model-expansion takes a CpuModelInfo argument. The
loongarch version of the command silently ignores the argument's
member @props. For instance,
{"execute": "query-cpu-model-expansion", "arguments": {"type": "static", "model": {"name": "la464", "props": null}}}
and
{"execute": "query-cpu-model-expansion", "arguments": {"type": "static", "model": {"name": "la464", "props": {"prop": null}}}}
succeed.
Add skeleton code for property processing that recognizes no
properties. Now the two commands fail as they should:
{"error": {"class": "GenericError", "desc": "Invalid parameter type for 'model.props', expected: object"}}
and
{"error": {"class": "GenericError", "desc": "Parameter 'model.props.prop' is unexpected"}}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240305145919.2186971-5-armbru@redhat.com>
[Drop #include now superfluous]
query-cpu-model-comparison, query-cpu-model-baseline, and
query-cpu-model-expansion take CpuModelInfo arguments. Errors in
@props members of these arguments are reported for 'props', without
further context. For instance, s390x rejects
{"execute": "query-cpu-model-comparison", "arguments": {"modela": {"name": "z13", "props": {}}, "modelb": {"name": "z14", "props": []}}}
with
{"error": {"class": "GenericError", "desc": "Invalid parameter type for 'props', expected: object"}}
This is unusual; the common QAPI unmarshaling machinery would complain
about 'modelb.props'. Our hand-written code to visit the @props
member neglects to provide the context.
Tweak it so it provides it. The command above now fails with
{"error": {"class": "GenericError", "desc": "Invalid parameter type for 'modelb.props', expected: dict"}}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240305145919.2186971-4-armbru@redhat.com>
Acked-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
CpuModelInfo member @props is semantically a mapping from name to
value, and syntactically a JSON object on the wire. This translates
to QDict in C. Since the QAPI schema language lacks the means to
express 'object', we use 'any' instead. This is QObject in C.
Commands taking a CpuModelInfo argument need to check the QObject is a
QDict.
The i386 version of qmp_query_cpu_model_expansion() fails to check.
Instead, @props is silently ignored when it's not an object. For
instance,
{"execute": "query-cpu-model-expansion", "arguments": {"type": "full", "model": {"name": "qemu64", "props": null}}}
succeeds.
Fix by refactoring the code to match the other targets. Now the
command fails as it should:
{"error": {"class": "GenericError", "desc": "Invalid parameter type for 'props', expected: object"}}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240305145919.2186971-3-armbru@redhat.com>
CpuModelInfo member @props is semantically a mapping from name to
value, and syntactically a JSON object on the wire. This translates
to QDict in C. Since the QAPI schema language lacks the means to
express 'object', we use 'any' instead. This is QObject in C.
Commands taking a CpuModelInfo argument need to check the QObject is a
QDict.
For arm, riscv, and s390x, the code checks right before passing the
QObject to visit_start_struct(). visit_start_struct() then checks
again.
Delete the first check.
The error message for @props that are not an object changes slightly
to the the message we get for this kind of type error in other
contexts. Minor improvement.
Additionally, error messages about members of @props now refer to
'props.prop-name' instead of just 'prop-name'. Another minor
improvement.
Both changes are visible in tests/qtest/arm-cpu-features.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240305145919.2186971-2-armbru@redhat.com>
Acked-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
[Drop #include now superfluous]
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-29-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-ID: <20240129164514.73104-28-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-27-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-26-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240129164514.73104-24-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-22-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-21-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-20-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240129164514.73104-19-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-18-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-17-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-16-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[thuth: Adjusted patch for hunk that moved to cpu_helper.c]
Signed-off-by: Thomas Huth <thuth@redhat.com>
QEMU coding style recommend using structure typedefs:
https://www.qemu.org/docs/master/devel/style.html#typedefs
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240129164514.73104-14-philmd@linaro.org>
[thuth: Break long lines to avoid checkpatch.pl errors]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Brian Cain <bcain@quicinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240129164514.73104-12-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-11-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-10-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mechanical patch produced running the command documented
in scripts/coccinelle/cpu_env.cocci_template header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-8-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since CPU() macro is a simple cast, the following are equivalent:
Object *obj;
CPUState *cs = CPU(obj)
In order to ease static analysis when running
scripts/coccinelle/cpu_env.cocci from the previous commit,
replace:
- CPU_GET_CLASS(cpu);
+ CPU_GET_CLASS(obj);
Most code use the 'cs' variable name for CPUState handle.
Replace few 's' -> 'cs' to unify cpu_reset_hold() style.
No logical change in this patch.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240129164514.73104-7-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Avoid CPUArchState local variable when cpu_env() is used once.
Mechanical patch using the following Coccinelle spatch script:
@@
type CPUArchState;
identifier env;
expression cs;
@@
{
- CPUArchState *env = cpu_env(cs);
... when != env
- env
+ cpu_env(cs)
... when != env
}
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240129164514.73104-5-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When a variable is initialized to &struct->field, use it
in place. Rationale: while this makes the code more concise,
this also helps static analyzers.
Mechanical change using the following Coccinelle spatch script:
@@
type S, F;
identifier s, m, v;
@@
S *s;
...
F *v = &s->m;
<+...
- &s->m
+ v
...+>
Inspired-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-2-philmd@linaro.org>
Acked-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
[thuth: Dropped hunks that need a rebase, and fixed sizeof() in pmu_realize()]
Signed-off-by: Thomas Huth <thuth@redhat.com>
As the comment in qapi/error, passing @errp to error_prepend() requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
...
* - It should not be passed to error_prepend(), error_vprepend() or
* error_append_hint(), because that doesn't work with &error_fatal.
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
ERRP_GUARD() could avoid the case when @errp is &error_fatal, the user
can't see this additional information, because exit() happens in
error_setg earlier than information is added [1].
In target/s390x/cpu_models.c, there are 2 functions passing @errp to
error_prepend() without ERRP_GUARD():
- check_compatibility()
- s390_realize_cpu_model()
Though both their @errp parameters point to their callers' local @err
virables and don't cause the issue as [1] said, to follow the
requirement of @errp, also add missing ERRP_GUARD() at their beginning.
[1]: Issue description in the commit message of commit ae7c80a7bd
("error: New macro ERRP_GUARD()").
Cc: David Hildenbrand <david@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Ilya Leoshkevich <iii@linux.ibm.com>
Cc: qemu-s390x@nongnu.org
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20240311033822.3142585-30-zhao1.liu@linux.intel.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
As the comment in qapi/error, passing @errp to error_prepend() requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
...
* - It should not be passed to error_prepend(), error_vprepend() or
* error_append_hint(), because that doesn't work with &error_fatal.
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
ERRP_GUARD() could avoid the case when @errp is the pointer of
error_fatal, the user can't see this additional information, because
exit() happens in error_setg earlier than information is added [1].
The sev_inject_launch_secret() passes @errp to error_prepend(), and as
an APIs defined in target/i386/sev.h, it is necessary to protect its
@errp with ERRP_GUARD().
To avoid the issue like [1] said, add missing ERRP_GUARD() at the
beginning of this function.
[1]: Issue description in the commit message of commit ae7c80a7bd
("error: New macro ERRP_GUARD()").
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240229143914.1977550-17-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This pull request contains two small patches to hv-balloon:
the first one replacing alloca() usage with g_malloc0() + g_autofree
and the second one adding additional declaration of a protocol message
struct with an optional field explicitly defined to avoid a Coverity
warning.
Also included is a VMBus patch to print a warning when it is enabled
without the recommended set of Hyper-V features (enlightenments) since
some Windows versions crash at boot in this case.
-----BEGIN PGP SIGNATURE-----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=kVny
-----END PGP SIGNATURE-----
Merge tag 'pull-hv-balloon-20240308' of https://github.com/maciejsszmigiero/qemu into staging
Hyper-V Dynamic Memory and VMBus misc small patches
This pull request contains two small patches to hv-balloon:
the first one replacing alloca() usage with g_malloc0() + g_autofree
and the second one adding additional declaration of a protocol message
struct with an optional field explicitly defined to avoid a Coverity
warning.
Also included is a VMBus patch to print a warning when it is enabled
without the recommended set of Hyper-V features (enlightenments) since
some Windows versions crash at boot in this case.
# -----BEGIN PGP SIGNATURE-----
#
# iQGzBAABCAAdFiEE4ndqq6COJv9aG0oJUrHW6VHQzgcFAmXrQeMACgkQUrHW6VHQ
# zgcvWwv9GUCDnidnDka8WGF2wgBEaPPdC2JXcqRFFLADISBAn/3fhsOERO6FwYuN
# pouhVEJnHpp9ueNAx+et51ySRzGCaL+VdOGGeReQllIOZGsnOnB8JfM58UE4lX4Z
# prCr72bxFsunxRqlqxssejrc8fBhgEQRPo5lQabl73rxftpXkNTHY0CGTwlvnaY1
# CzEBTBuowzkZJbQYDL8Qim2HrYqrSnOaend6bbrj9P6P+UFw9wLJU5tkfYCiHUjg
# Ux2Fjjx+5+qD9yE7khtxSHqjwWYkR7xA9di1yv4Znqg18gzdbuqnlrKR7F0v98yh
# sWFy+fyfVRDg+G2yh2F+vAUjmAJUrfw5+GL3uZTWIevoQUoSHBQfgUEJrlIKvykZ
# WP1XuAZRH3m2akDOXOWZVcDhkb3zPKtPJYZ2WncBZk+DLCs/vg94Taq0FcZefBTn
# 6qsFjs2lHz96uOSzgqICfU34ghcxfU5xgzmvKxKAiriOItmRMHgIYOXLHRfaIJhV
# MT/9OMuW
# =kVny
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 08 Mar 2024 16:50:43 GMT
# gpg: using RSA key E2776AABA08E26FF5A1B4A0952B1D6E951D0CE07
# gpg: Good signature from "Maciej S. Szmigiero <mail@maciej.szmigiero.name>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 727A 0D4D DB9E D9F6 039B ECEF 847F 5E37 90CE 0977
# Subkey fingerprint: E277 6AAB A08E 26FF 5A1B 4A09 52B1 D6E9 51D0 CE07
* tag 'pull-hv-balloon-20240308' of https://github.com/maciejsszmigiero/qemu:
vmbus: Print a warning when enabled without the recommended set of features
hv-balloon: define dm_hot_add_with_region to avoid Coverity warning
hv-balloon: avoid alloca() usage
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the code to a separate file so that we do not have to compile
it anymore if CONFIG_ARM_V7M is not set.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 20240308141051.536599-2-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some Windows versions crash at boot or fail to enable the VMBus device if
they don't see the expected set of Hyper-V features (enlightenments).
Since this provides poor user experience let's warn user if the VMBus
device is enabled without the recommended set of Hyper-V features.
The recommended set is the minimum set of Hyper-V features required to make
the VMBus device work properly in Windows Server versions 2016, 2019 and
2022.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
G-stage translation should be considered to be user-level access in
riscv_cpu_get_phys_page_debug(), as already done in riscv_cpu_tlb_fill().
This fixes a bug that prevents gdb from reading memory while the VM is
running in VS-mode.
Signed-off-by: Hiroaki Yamamoto <hrak1529@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240228081028.35081-1-hrak1529@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The result of (8 - 3 - vlmul) is negative when vlmul >= 6,
and results in wrong vill.
Signed-off-by: demin.han <demin.han@starfivetech.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240225174114.5298-1-demin.han@starfivetech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
After the 'mark_vs_dirty' changes from the previous patch the 'is_store'
bool is unused in some load/store functions that were changed. Remove it.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240306171932.549549-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
While discussing a problem with how we're (not) setting vstart_eq_zero
Richard had the following to say w.r.t the conditional mark_vs_dirty()
calls on load/store functions [1]:
"I think it's required to have stores set dirty unconditionally, before
the operation.
Consider a store that traps on the 2nd element, leaving vstart = 2, and
exiting to the main loop via exception. The exception enters the kernel
page fault handler. The kernel may need to fault in the page for the
process, and in the meantime task switch.
If vs dirty is not already set, the kernel won't know to save vector
state on task switch."
Do a mark_vs_dirty() before both loads and stores.
[1] https://lore.kernel.org/qemu-riscv/72c7503b-0f43-44b8-aa82-fbafed2aac0c@linaro.org/
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240306171932.549549-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
mcountinhibit, mcounteren, scounteren and hcounteren must always be 32-bit
by privileged spec
Signed-off-by: Vadim Shakirov <vadim.shakirov@syntacore.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240202113919.18236-1-vadim.shakirov@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
smaia and ssaia were ratified in August 25th 2023 [1].
zvfh and zvfhmin were ratified in August 2nd 2023 [2].
zfbfmin and zvfbf(min|wma) are frozen and moved to public review since
Dec 16th 2023 [3].
zaamo and zalrsc are both marked as "Frozen" since January 24th 2024
[4].
[1] https://jira.riscv.org/browse/RVS-438
[2] https://jira.riscv.org/browse/RVS-871
[3] https://jira.riscv.org/browse/RVS-704
[4] https://jira.riscv.org/browse/RVS-1995
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240301144053.265964-1-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The last KVM extensions added were back in 6.6. Sync them to Linux 6.8.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240304134732.386590-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Ztso extension is already ratified, this adds it as a CPU property
and adds various fences throughout the port in order to allow TSO
targets to function on weaker hosts. We need no fences for AMOs as
they're already SC, the places we need barriers are described.
These fences are placed in the RISC-V backend rather than TCG as is
planned for x86-on-arm64 because RISC-V allows heterogeneous (and
likely soon dynamic) hart memory models.
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-ID: <20240207122256.902627-2-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add missing include guard in pmu.h to avoid the problem of double
inclusion.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240220110907.10479-1-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Added xATP_MODE validation for vsatp/hgatp CSRs.
The xATP register is an SXLEN-bit read/write WARL register, so
the legal value must be returned (See riscv-privileged-20211203, SATP/VSATP/HGATP CSRs).
Signed-off-by: Irina Ryapolova <irina.ryapolova@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240109145923.37893-2-irina.ryapolova@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The SATP register is an SXLEN-bit read/write WARL register. It means that CSR fields are only defined
for a subset of bit encodings, but allow any value to be written while guaranteeing to return a legal
value whenever read (See riscv-privileged-20211203, SATP CSR).
For example on rv64 we are trying to write to SATP CSR val = 0x1000000000000000 (SATP_MODE = 1 - Reserved for standard use)
and after that we are trying to read SATP_CSR. We read from the SATP CSR value = 0x1000000000000000, which is not a correct
operation (return illegal value).
Signed-off-by: Irina Ryapolova <irina.ryapolova@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240109145923.37893-1-irina.ryapolova@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Named features are extensions which don't make sense for users to
control and are therefore not exposed on the command line. However,
svade is an extension which makes sense for users to control, so treat
it like a "normal" extension. The default is false, even for the max
cpu type, since QEMU has always implemented hardware A/D PTE bit
updating, so users must opt into svade (or get it from a CPU type
which enables it by default).
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240215223955.969568-7-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Gate hardware A/D PTE bit updating on {m,h}envcfg.ADUE and only
enable menvcfg.ADUE on reset if svade has not been selected. Now
that we also consider svade, we have four possible configurations:
1) !svade && !svadu
use hardware updating and there's no way to disable it
(the default, which maintains past behavior. Maintaining
the default, even with !svadu is a change that fixes [1])
2) !svade && svadu
use hardware updating, but also provide {m,h}envcfg.ADUE,
allowing software to switch to exception mode
(being able to switch is a change which fixes [1])
3) svade && !svadu
use exception mode and there's no way to switch to hardware
updating
(this behavior change fixes [2])
4) svade && svadu
use exception mode, but also provide {m,h}envcfg.ADUE,
allowing software to switch to hardware updating
(this behavior change fixes [2])
Fixes: 0af3f115e6 ("target/riscv: Add *envcfg.HADE related check in address translation") [1]
Fixes: 48531f5adb ("target/riscv: implement svade") [2]
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240215223955.969568-6-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The hypervisor should decide what it wants to enable. Zero all
configuration enable bits on reset.
Also, commit ed67d63798 ("target/riscv: Update CSR bits name for
svadu extension") missed one reference to 'hade'. Change it now.
Fixes: 0af3f115e6 ("target/riscv: Add *envcfg.HADE related check in address translation")
Fixes: ed67d63798 ("target/riscv: Update CSR bits name for svadu extension")
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240215223955.969568-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RVA22U64 and RVA22S64 profiles mandates certain extensions that,
until now, we were implying that they were available.
We can't do this anymore since named features also has a riscv,isa
entry. Let's add them to riscv_cpu_named_features[].
Instead of adding one bool for each named feature that we'll always
implement, i.e. can't be turned off, add a 'ext_always_enabled' bool in
cpu->cfg. This bool will be set to 'true' in TCG accel init, and all
named features will point to it. This also means that KVM won't see
these features as always enable, which is our intention.
If any accelerator adds support to disable one of these features, we'll
have to promote them to regular extensions and allow users to disable it
via command line.
After this patch, here's the riscv,isa from a buildroot using the
'rva22s64' CPU:
# cat /proc/device-tree/cpus/cpu@0/riscv,isa
rv64imafdc_zic64b_zicbom_zicbop_zicboz_ziccamoa_ziccif_zicclsm_ziccrse_
zicntr_zicsr_zifencei_zihintpause_zihpm_za64rs_zfhmin_zca_zcd_zba_zbb_
zbs_zkt_ssccptr_sscounterenw_sstvala_sstvecd_svade_svinval_svpbmt#
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240215223955.969568-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Further discussions after the introduction of rva22 support in QEMU
revealed that what we've been calling 'named features' are actually
regular extensions, with their respective riscv,isa DTs. This is
clarified in [1]. [2] is a bug tracker asking for the profile spec to be
less cryptic about it.
As far as QEMU goes we understand extensions as something that the user
can enable/disable in the command line. This isn't the case for named
features, so we'll have to reach a middle ground.
We'll keep our existing nomenclature 'named features' to refer to any
extension that the user can't control in the command line. We'll also do
the following:
- 'svade' and 'zic64b' flags are renamed to 'ext_svade' and
'ext_zic64b'. 'ext_svade' and 'ext_zic64b' now have riscv,isa strings and
priv_spec versions;
- skip name feature check in cpu_bump_multi_ext_priv_ver(). Now that
named features have a riscv,isa and an entry in isa_edata_arr[] we
don't need to gate the call to cpu_cfg_ext_get_min_version() anymore.
[1] https://github.com/riscv/riscv-profiles/issues/121
[2] https://github.com/riscv/riscv-profiles/issues/142
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240215223955.969568-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Recent changes in options handling removed the 'mmu' default the bare
CPUs had, meaning that we must enable 'mmu' by hand when using the
rva22s64 profile CPU.
Given that this profile is setting a satp mode, it already implies that
we need a 'mmu'. Enable the 'mmu' in this case.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240215223955.969568-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The original implementation sets $pc to the address read from the jump
vector table first and links $ra with the address of the next instruction
after the updated $pc. After jumping to the updated $pc and executing the
next ret instruction, the program jumps to $ra, which is in the same
function currently executing, which results in an infinite loop.
This commit stores the jump address in a temporary, updates $ra with the
current $pc, and copies the temporary to $pc.
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240207081820.28559-1-jason.chien@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
While the 8-bit input elements are sequential in the input vector,
the 32-bit output elements are not sequential in the output matrix.
Do not attempt to compute 2 32-bit outputs at the same time.
Cc: qemu-stable@nongnu.org
Fixes: 23a5e3859f ("target/arm: Implement SME integer outer product")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2083
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240305163931.242795-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable all FEAT_ECV features on the 'max' CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-9-peter.maydell@linaro.org
When ID_AA64MMFR0_EL1.ECV is 0b0010, a new register CNTPOFF_EL2 is
implemented. This is similar to the existing CNTVOFF_EL2, except
that it controls a hypervisor-adjustable offset made to the physical
counter and timer.
Implement the handling for this register, which includes control/trap
bits in SCR_EL3 and CNTHCTL_EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-8-peter.maydell@linaro.org
For FEAT_ECV, new registers CNTPCTSS_EL0 and CNTVCTSS_EL0 are
defined, which are "self-synchronized" views of the physical and
virtual counts as seen in the CNTPCT_EL0 and CNTVCT_EL0 registers
(meaning that no barriers are needed around accesses to them to
ensure that reads of them do not occur speculatively and out-of-order
with other instructions).
For QEMU, all our system registers are self-synchronized, so we can
simply copy the existing implementation of CNTPCT_EL0 and CNTVCT_EL0
to the new register encodings.
This means we now implement all the functionality required for
ID_AA64MMFR0_EL1.ECV == 0b0001.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-7-peter.maydell@linaro.org
The functionality defined by ID_AA64MMFR0_EL1.ECV == 1 is:
* four new trap bits for various counter and timer registers
* the CNTHCTL_EL2.EVNTIS and CNTKCTL_EL1.EVNTIS bits which control
scaling of the event stream. This is a no-op for us, because we don't
implement the event stream (our WFE is a NOP): all we need to do is
allow CNTHCTL_EL2.ENVTIS to be read and written.
* extensions to PMSCR_EL1.PCT, PMSCR_EL2.PCT, TRFCR_EL1.TS and
TRFCR_EL2.TS: these are all no-ops for us, because we don't implement
FEAT_SPE or FEAT_TRF.
* new registers CNTPCTSS_EL0 and NCTVCTSS_EL0 which are
"self-sychronizing" views of the CNTPCT_EL0 and CNTVCT_EL0, meaning
that no barriers are needed around their accesses. For us these
are just the same as the normal views, because all our sysregs are
inherently self-sychronizing.
In this commit we implement the trap handling and permit the new
CNTHCTL_EL2 bits to be written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-6-peter.maydell@linaro.org
Don't allow the guest to write CNTHCTL_EL2 bits which don't exist.
This is not strictly architecturally required, but it is how we've
tended to implement registers more recently.
In particular, bits [19:18] are only present with FEAT_RME,
and bits [17:12] will only be present with FEAT_ECV.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-5-peter.maydell@linaro.org
We prefer the FIELD macro over ad-hoc #defines for register bits;
switch CNTHCTL to that style before we add any more bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-4-peter.maydell@linaro.org
The timer _EL02 registers should UNDEF for invalid accesses from EL2
or EL3 when HCR_EL2.E2H == 0, not take a cp access trap. We were
delivering the exception to EL2 with the wrong syndrome.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-3-peter.maydell@linaro.org
cpu.h has a lot of #defines relating to CPU register fields.
Most of these aren't actually used outside target/arm code,
so there's no point in cluttering up the cpu.h file with them.
Move some easy ones to internals.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-2-peter.maydell@linaro.org
This makes the output suitable when used for plugins.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240305121005.3528075-29-alex.bennee@linaro.org>
If translation is enabled, and the PTE memory type is Device,
enable checking alignment via TLB_CHECK_ALIGNMENT. While the
check is done later than it should be per the ARM, it's better
than not performing the check at all.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301204110.656742-7-richard.henderson@linaro.org
[PMM: tweaks to comment text]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
If translation is disabled, the default memory type is Device, which
requires alignment checking. This is more optimally done early via
the MemOp given to the TCG memory operation.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reported-by: Idan Horowitz <idan.horowitz@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301204110.656742-6-richard.henderson@linaro.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1204
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the target to set tlb flags to apply to all of the
comparators. Remove MemTxAttrs.byte_swap, as the bit is
not relevant to memory transactions, only the page mapping.
Adjust target/sparc to set TLB_BSWAP directly.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301204110.656742-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we have removed TARGET_PAGE_BITS_MIN-6 from
TLB_FLAGS_MASK, we can test for 32-byte alignment.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301204110.656742-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When calculating the IOR for the exception handlers, the current
unwind_breg value is needed on 64-bit hppa machines.
Restore that value by calling cpu_restore_state() earlier, which in turn
calls hppa_restore_state_to_opc() which restores the unwind_breg for the
current instruction.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 3824e0d643 ("target/hppa: Export function hppa_set_ior_and_isr()")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Unaligned 64-bit accesses were found in Linux to clobber carry bits,
resulting in bad results if an arithmetic operation involving a
carry bit was executed after an unaligned 64-bit operation.
hppa 2.0 defines additional carry bits in PSW register bits 32..39.
When restoring PSW after executing an unaligned instruction trap, those
bits were not cleared and ended up to be active all the time. Since there
are no bits other than the upper carry bits needed in the upper 32 bit of
env->psw and since those are stored in env->psw_cb, just clear the entire
upper 32 bit when storing psw to solve the problem unconditionally.
Fixes: 931adff314 ("target/hppa: Update cpu_hppa_get/put_psw for hppa64")
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Charlie Jenkins <charlie@rivosinc.com>
Cc: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Since alpha binaries are generally built for multiple
page sizes, it is trivial to allow the page size to vary.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20240102015808.132373-34-richard.henderson@linaro.org>
Since ppc binaries are generally built for multiple
page sizes, it is trivial to allow the page size to vary.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20240102015808.132373-33-richard.henderson@linaro.org>
Since aarch64 binaries are generally built for multiple
page sizes, it is trivial to allow the page size to vary.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20240102015808.132373-31-richard.henderson@linaro.org>
These members will be used to help plugins to identify registers.
The added members in instances of GDBFeature dynamically generated by
CPUs will be filled in later changes.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20231213-gdb-v17-10-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-15-alex.bennee@linaro.org>
This function is no longer used.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231213-gdb-v17-9-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-14-alex.bennee@linaro.org>
GDBFeature has the num_regs member so use it where applicable to
remove magic numbers.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20231213-gdb-v17-8-777047380591@daynix.com>
[AJB: remove core reg check from microblaze read reg]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-13-alex.bennee@linaro.org>
Align the parameters of gdb_get_reg_cb and gdb_set_reg_cb with the
gdb_read_register and gdb_write_register members of CPUClass to allow
to unify the logic to access registers of the core and coprocessors
in the future.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231213-gdb-v17-6-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-11-alex.bennee@linaro.org>
This is a tree-wide change to introduce GDBFeature parameter to
gdb_register_coprocessor(). The new parameter just replaces num_regs
and xml parameters for now. GDBFeature will be utilized to simplify XML
lookup in a following change.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231213-gdb-v17-4-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-9-alex.bennee@linaro.org>
In preparation for a change to use GDBFeature as a parameter of
gdb_register_coprocessor(), convert the internal representation of
dynamic feature from plain XML to GDBFeature.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20231213-gdb-v17-3-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-8-alex.bennee@linaro.org>
In preparation for a change to use GDBFeature as a parameter of
gdb_register_coprocessor(), convert the internal representation of
dynamic feature from plain XML to GDBFeature.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231213-gdb-v17-2-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-7-alex.bennee@linaro.org>
In preparation for a change to use GDBFeature as a parameter of
gdb_register_coprocessor(), convert the internal representation of
dynamic feature from plain XML to GDBFeature.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231213-gdb-v17-1-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-6-alex.bennee@linaro.org>
The A20 mask is only applied to the final memory access. Nested
page tables are always walked with the raw guest-physical address.
Unlike the previous patch, in this one the masking must be kept, but
it was done too early.
Cc: qemu-stable@nongnu.org
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If ptw_translate() does a MMU_PHYS_IDX access, the A20 mask is already
applied in get_physical_address(), which is called via probe_access_full()
and x86_cpu_tlb_fill().
If ptw_translate() on the other hand does a MMU_NESTED_IDX access,
the A20 mask must not be applied to the address that is looked up in
the nested page tables; it must be applied only to the addresses that
hold the NPT entries (which is achieved via MMU_PHYS_IDX, per the
previous paragraph).
Therefore, we can remove A20 masking from the computation of the page
table entry's address, and let get_physical_address() or mmu_translate()
apply it when they know they are returning a host-physical address.
Cc: qemu-stable@nongnu.org
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The address translation logic in get_physical_address() will currently
truncate physical addresses to 32 bits unless long mode is enabled.
This is incorrect when using physical address extensions (PAE) outside
of long mode, with the result that a 32-bit operating system using PAE
to access memory above 4G will experience undefined behaviour.
The truncation code was originally introduced in commit 33dfdb5 ("x86:
only allow real mode to access 32bit without LMA"), where it applied
only to translations performed while paging is disabled (and so cannot
affect guests using PAE).
Commit 9828198 ("target/i386: Add MMU_PHYS_IDX and MMU_NESTED_IDX")
rearranged the code such that the truncation also applied to the use
of MMU_PHYS_IDX and MMU_NESTED_IDX. Commit 4a1e9d4 ("target/i386: Use
atomic operations for pte updates") brought this truncation into scope
for page table entry accesses, and is the first commit for which a
Windows 10 32-bit guest will reliably fail to boot if memory above 4G
is present.
The truncation code however is not completely redundant. Even though the
maximum address size for any executed instruction is 32 bits, helpers for
operations such as BOUND, FSAVE or XSAVE may ask get_physical_address()
to translate an address outside of the 32-bit range, if invoked with an
argument that is close to the 4G boundary. Likewise for processor
accesses, for example TSS or IDT accesses, when EFER.LMA==0.
So, move the address truncation in get_physical_address() so that it
applies to 32-bit MMU indexes, but not to MMU_PHYS_IDX and MMU_NESTED_IDX.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2040
Fixes: 4a1e9d4d11 ("target/i386: Use atomic operations for pte updates", 2022-10-18)
Cc: qemu-stable@nongnu.org
Co-developed-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Accesses from a 32-bit environment (32-bit code segment for instruction
accesses, EFER.LMA==0 for processor accesses) have to mask away the
upper 32 bits of the address. While a bit wasteful, the easiest way
to do so is to use separate MMU indexes. These days, QEMU anyway is
compiled with a fixed value for NB_MMU_MODES. Split MMU_USER_IDX,
MMU_KSMAP_IDX and MMU_KNOSMAP_IDX in two.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Harsh Prateek Bora