Just use 1 in skip draw if you want to use it
openGL code will soon be fixed to support depth correctly (and I hope dx in the future)
Conflicts:
plugins/GSdx/GSState.cpp
plugins/GSdx/GSState.h
Old way various check boxes to configure the plugin
New way an unified drop down list
* Level 0 (dev only) => disable (mostly) all hacks and auto skip depth.
* Level 1 (dev only ) => enable oi/oo/cu hacks, others remains disabled
* Level 2 (GL) => enable most hacks except a couple of one that were fixed on openGL (speed impact)
* Level 3 (DX) => enable all hacks
* Level 4 => enable also aggresive CRC
Note: windows gui must be updated, and it will be nice to create a global tooltip
initialization of IDC_ROUND_SPRITE
set&get config for round offset.
three state checkbox for the hack.
define IDC for round offset.
Linux (GUI) refresh.
typo
Also disabled the gsdx AF options for the OGL renderer (because it's not implemented for that yet).
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5881 96395faa-99c1-11dd-bbfe-3dabce05a288
Adds anisotropic texture filtering (1x-16x) to the hardware settings. Enhances the visual quality of textures that are at oblique viewing angles.
Anisotropic filtering is automatically disabled if: 8-bit textures are enabled.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5878 96395faa-99c1-11dd-bbfe-3dabce05a288
Slight adjustments to positions in the GUI also (OCD'd the spacing a little :P)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5796 96395faa-99c1-11dd-bbfe-3dabce05a288
Added a check box and config code for the fxaa shader.
It's not currently hooked up since the shader setup might get replaced in a day or two.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5777 96395faa-99c1-11dd-bbfe-3dabce05a288
Probably only of interest to testers (and me). Absolutely do NOT select the reference device even out of extreme morbid curiosity. It's not even very good at being a reference despite being slower than you can probably believe.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5358 96395faa-99c1-11dd-bbfe-3dabce05a288
Now, a note about the actual issue. Destination alpha tests can be used on the GS as one of the workarounds for a lack of stencils. If you use a destination alpha test and leave alpha writing on, the GS will only write each pixel until you write an alpha value which would fail the test. This works to a point in gsdx without further hacking, but that point is when within a single batch of primitives the same pixels are written multiple times and the destination alpha test is expected to update. I did experimentally make a tight loop updating the stencil with a draw then drawing for one primitive at a time, but it was prohibitively slow (over 80% fps loss, you really don't want to know).
Destination alpha testing cannot be directly implemented in D3D9 or D3D10, but (probably) can in D3D11 (with a speed hit for sure, but I doubt it'll be 80%). I'll be getting a new graphics card and looking into that.
And before some idiot says it, the answer is no. OpenGL does not help.
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5346 96395faa-99c1-11dd-bbfe-3dabce05a288
Also set the auto deinterlace mode in GSdx when the .ini isn't present (instead of "none").
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5270 96395faa-99c1-11dd-bbfe-3dabce05a288
- Added "Aggressive-CRC" checkbox at the HW hacks section of the config dialog.
- The following hacks are now activated only in aggressive mode:
- God of War 2: disable water effect/lines, disable global haze.
- FFX, FFX2, SSX3 (the full crc hack from r5214).
- Shadow of the Colossus: disable (over)bloom.
- Reverted the Valkyrie Profile 2 hack to pre- r5214.
- Some CRC fixes by comments on r5214.
- Regression fix of dynamic crc hack (INITIAL_MODE = 0 didn't compile)
git-svn-id: http://pcsx2.googlecode.com/svn/trunk@5221 96395faa-99c1-11dd-bbfe-3dabce05a288
refractionpcsx2