Let's reset m_last_used for each register that will be used
in an instruction before we start allocating any of them,
so that one of the earlier allocations doesn't spill a
register that we want in a later allocation. (We must still
also increment/reset m_last_used in R and RW, otherwise we
end up in trouble when emulating lmw/stmw since those access
more guest registers than there are available host registers.)
This should ensure that the asserts added earlier in this
pull request are never triggered.
If the register pressure is high when allocating registers,
Arm64FPRCache may spill a guest register which we are going to
allocate later during the current instruction, which has the
side effect of turning it into double precision. This will have
bad consequences if we are assuming that it is single precision,
so let's add some asserts to detect if that ever happens.
Check return value of calls to File::CreateTempDir() from CoreTiming,
FileSystem, and MMIO test classes to verify the test user directory
exists, and fail the tests otherwise.
Previously, eaddr would only be partially initialized in the ipv6 case.
Even if there's no support for it, we may as well ensure that the
variable always has deterministic initialization.
While we're at it, we can make the parameter a const reference, given no
members are modified.
EmulationActivity has an instance of Settings. If you go to
SettingsActivity from EmulationActivity and change some settings,
the changes get saved to disk, but EmulationActivity's Settings
instance still contains the old settings in its map of all
settings (assuming the EmulationActivity was not killed by the
system to save memory). Then, once you're done playing your
game and exit EmulationActivity, EmulationActivity calls
Settings.saveSettings. This call to saveSettings first overwrites
the entire INI file with its map of all settings (which is
outdated) in order to save any legacy settings that have changed
(which they haven't, since the GUI doesn't let you change legacy
settings while a game is running). Then, it asks the new config
system to write the most up-to-date values available for non-legacy
settings, which should make all the settings be up-to-date again.
The problem here is that the new config system would skip writing
to disk if no settings changes had been made since the last time
we asked it to write to disk (i.e. since SettingsActivity exited).
NB: Calling Settings.loadSettings in EmulationActivity.onResume
is not a working solution. I assume this is because
SettingsActivity saves its settings in onStop and not onPause.
For certain occurrences of nandx/norx, we declare a ReadWrite constraint
on the destination register, even though the value of the destination
register is irrelevant. This false dependency would force the RegCache
to generate a redundant MOV when the destination register wasn't already
assigned to a host register.
Example 1:
BF 00 00 00 00 mov edi,0
8B FE mov edi,esi
F7 D7 not edi
Example 2:
8B 7D 80 mov edi,dword ptr [rbp-80h]
8B FE mov edi,esi
F7 D7 not edi
FinalizeCarryOverflow didn't maintain XER[OV/SO] properly due to an
oversight. Here's the code it would generate:
0: 9c pushf
1: 80 65 3b fe and BYTE PTR [rbp+0x3b],0xfe
5: 71 04 jno b <jno>
7: c6 45 3b 03 mov BYTE PTR [rbp+0x3b],0x3
000000000000000b <jno>:
b: 9d popf
At first glance it seems reasonable. The host flags are carefully
preserved with PUSHF. The AND instruction clears XER[OV]. Next, an
conditional branch checks the host's overflow flag and, if needed, skips
over a MOV that sets XER[OV/SO]. Finally, host flags are restored with
POPF.
However, the AND instruction also clears the host's overflow flag. As a
result, the branch that follows it is always taken and the MOV is always
skipped. The end result is that XER[OV] is always cleared while XER[SO]
is left unchanged.
Putting POPF immediately after the AND would fix this, but we already
have GenerateOverflow doing it correctly (and without the PUSHF/POPF
shenanigans too). So let's just use that instead.
Léo Lam