Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20200120101023.16030-3-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If LPIs are disabled, KVM will just ignore the GICR_PENDBASER.PTZ bit when
restoring GICR_CTLR. Setting PTZ here makes littlt sense in "reduce GIC
initialization time".
And what's worse, PTZ is generally programmed by guest to indicate to the
Redistributor whether the LPI Pending table is zero when enabling LPIs.
If migration is triggered when the PTZ has just been cleared by guest (and
before enabling LPIs), we will see PTZ==1 on the destination side, which
is not as expected. Let's just drop this hackish userspace behavior.
Also take this chance to refine the comment a bit.
Fixes: 367b9f527b ("hw/intc/arm_gicv3_kvm: Implement get/put functions")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20200119133051.642-1-yuzenghui@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace deprecated qdev_reset_all by resettable_cold_reset_fn for
the ipl registration in the main reset handlers.
This does not impact the behavior for the following reasons:
+ at this point resettable just call the old reset methods of devices
and buses in the same order than qdev/qbus.
+ resettable handlers registered with qemu_register_reset are
serialized; there is no interleaving.
+ eventual explicit calls to legacy reset API (device_reset or
qdev/qbus_reset) inside this reset handler will not be masked out
by resettable mechanism; they do not go through resettable api.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200123132823.1117486-12-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Deprecate device_legacy_reset(), qdev_reset_all() and
qbus_reset_all() to be replaced by new functions
device_cold_reset() and bus_cold_reset() which uses resettable API.
Also introduce resettable_cold_reset_fn() which may be used as a
replacement for qdev_reset_all_fn and qbus_reset_all_fn().
Following patches will be needed to look at legacy reset call sites
and switch to resettable api. The legacy functions will be removed
when unused.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-9-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit make use of the resettable API to reset the device being
hotplugged when it is realized. Also it ensures it is put in a reset
state coherent with the parent it is plugged into.
Note that there is a difference in the reset. Instead of resetting
only the hotplugged device, we reset also its subtree (switch to
resettable API). This is not expected to be a problem because
sub-buses are just realized too. If a hotplugged device has any
sub-buses it is logical to reset them too at this point.
The recently added should_be_hidden and PCI's partially_hotplugged
mechanisms do not interfere with realize operation:
+ In the should_be_hidden use case, device creation is
delayed.
+ The partially_hotplugged mechanism prevents a device to be
unplugged and unrealized from qdev POV and unrealized.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-8-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In qdev_set_parent_bus(), when changing the parent bus of a
realized device, if the source and destination buses are not in the
same reset state, some adaptations are required. This patch adds
needed call to resettable_change_parent() to make sure a device reset
state stays coherent with its parent bus.
The addition is a no-op if:
1. the device being parented is not realized.
2. the device is realized, but both buses are not under reset.
Case 2 means that as long as qdev_set_parent_bus() is called
during the machine realization procedure (which is before the
machine reset so nothing is in reset), it is a no op.
There are 52 call sites of qdev_set_parent_bus(). All but one fall
into the no-op case:
+ 29 trivial calls related to virtio (in hw/{s390x,display,virtio}/
{vhost,virtio}-xxx.c) to set a vdev(or vgpu) composing device
parent bus just before realizing the same vdev(vgpu).
+ hw/core/qdev.c: when creating a device in qdev_try_create()
+ hw/core/sysbus.c: when initializing a device in the sysbus
+ hw/i386/amd_iommu.c: before realizing AMDVIState/pci
+ hw/isa/piix4.c: before realizing PIIX4State/rtc
+ hw/misc/auxbus.c: when creating an AUXBus
+ hw/misc/auxbus.c: when creating an AUXBus child
+ hw/misc/macio/macio.c: when initializing a MACIOState child
+ hw/misc/macio/macio.c: before realizing NewWorldMacIOState/pmu
+ hw/misc/macio/macio.c: before realizing NewWorldMacIOState/cuda
+ hw/net/virtio-net.c: Used for migration when using the failover
mechanism to migration a vfio-pci/net. It is
a no-op because at this point the device is
already on the bus.
+ hw/pci-host/designware.c: before realizing DesignwarePCIEHost/root
+ hw/pci-host/gpex.c: before realizing GPEXHost/root
+ hw/pci-host/prep.c: when initialiazing PREPPCIState/pci_dev
+ hw/pci-host/q35.c: before realizing Q35PCIHost/mch
+ hw/pci-host/versatile.c: when initializing PCIVPBState/pci_dev
+ hw/pci-host/xilinx-pcie.c: before realizing XilinxPCIEHost/root
+ hw/s390x/event-facility.c: when creating SCLPEventFacility/
TYPE_SCLP_QUIESCE
+ hw/s390x/event-facility.c: ditto with SCLPEventFacility/
TYPE_SCLP_CPU_HOTPLUG
+ hw/s390x/sclp.c: Not trivial because it is called on a SLCPDevice
just after realizing it. Ok because at this point the destination
bus (sysbus) is not in reset; the realize step is before the
machine reset.
+ hw/sd/core.c: Not OK. Used in sdbus_reparent_card(). See below.
+ hw/ssi/ssi.c: Used to put spi slave on spi bus and connect the cs
line in ssi_auto_connect_slave(). Ok because this function is only
used in realize step in hw/ssi/aspeed_smc.ci, hw/ssi/imx_spi.c,
hw/ssi/mss-spi.c, hw/ssi/xilinx_spi.c and hw/ssi/xilinx_spips.c.
+ hw/xen/xen-legacy-backend.c: when creating a XenLegacyDevice device
+ qdev-monitor.c: in device hotplug creation procedure before realize
Note that this commit alone will have no effect, right now there is no
use of resettable API to reset anything. So a bus will never be tagged
as in-reset by this same API.
The one place where side-effect will occurs is in hw/sd/core.c in
sdbus_reparent_card(). This function is only used in the raspi machines,
including during the sysbus reset procedure. This case will be
carrefully handled when doing the multiple phase reset transition.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-7-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a function resettable_change_parent() to do the required
plumbing when changing the parent a of Resettable object.
We need to make sure that the reset state of the object remains
coherent with the reset state of the new parent.
We make the 2 following hypothesis:
+ when an object is put in a parent under reset, the object goes in
reset.
+ when an object is removed from a parent under reset, the object
leaves reset.
The added function avoids any glitch if both old and new parent are
already in reset.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-6-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds support of Resettable interface to buses and devices:
+ ResettableState structure is added in the Bus/Device state
+ Resettable methods are implemented.
+ device/bus_is_in_reset function defined
This commit allows to transition the objects to the new
multi-phase interface without changing the reset behavior at all.
Object single reset method can be split into the 3 different phases
but the 3 phases are still executed in a row for a given object.
From the qdev/qbus reset api point of view, nothing is changed.
qdev_reset_all() and qbus_reset_all() are not modified as well as
device_legacy_reset().
Transition of an object must be done from parent class to child class.
Care has been taken to allow the transition of a parent class
without requiring the child classes to be transitioned at the same
time. Note that SysBus and SysBusDevice class do not need any transition
because they do not override the legacy reset method.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-5-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit defines an interface allowing multi-phase reset. This aims
to solve a problem of the actual single-phase reset (built in
DeviceClass and BusClass): reset behavior is dependent on the order
in which reset handlers are called. In particular doing external
side-effect (like setting an qemu_irq) is problematic because receiving
object may not be reset yet.
The Resettable interface divides the reset in 3 well defined phases.
To reset an object tree, all 1st phases are executed then all 2nd then
all 3rd. See the comments in include/hw/resettable.h for a more complete
description. The interface defines 3 phases to let the future
possibility of holding an object into reset for some time.
The qdev/qbus reset in DeviceClass and BusClass will be modified in
following commits to use this interface. A mechanism is provided
to allow executing a transitional reset handler in place of the 2nd
phase which is executed in children-then-parent order inside a tree.
This will allow to transition devices and buses smoothly while
keeping the exact current qdev/qbus reset behavior for now.
Documentation will be added in a following commit.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-4-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds trace events to reset procedure and when updating the parent
bus of a device.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-3-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a temporary device_legacy_reset function doing what
device_reset does to prepare for the transition with Resettable
API.
All occurrence of device_reset in the code tree are also replaced
by device_legacy_reset.
The new resettable API has different prototype and semantics
(resetting child buses as well as the specified device). Subsequent
commits will make the changeover for each call site individually; once
that is complete device_legacy_reset() will be removed.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-2-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since we enabled parallel TCG code generation for softmmu (see
commit 3468b59 "tcg: enable multiple TCG contexts in softmmu")
and its subsequent fix (commit 72649619 "add .min_cpus and
.default_cpus fields to machine_class"), the raspi machines are
restricted to always use their 4 cores:
See in hw/arm/raspi2 (with BCM283X_NCPUS set to 4):
222 static void raspi2_machine_init(MachineClass *mc)
223 {
224 mc->desc = "Raspberry Pi 2";
230 mc->max_cpus = BCM283X_NCPUS;
231 mc->min_cpus = BCM283X_NCPUS;
232 mc->default_cpus = BCM283X_NCPUS;
235 };
236 DEFINE_MACHINE("raspi2", raspi2_machine_init)
We can no longer use the -smp option, as we get:
$ qemu-system-arm -M raspi2 -smp 1
qemu-system-arm: Invalid SMP CPUs 1. The min CPUs supported by machine 'raspi2' is 4
Since we can not set the TYPE_BCM283x SOC "enabled-cpus" with -smp,
remove the unuseful code.
We can achieve the same by using the '-global bcm2836.enabled-cpus=1'
option.
Reported-by: Laurent Bonnans <laurent.bonnans@here.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200120235159.18510-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Following the pattern of the work recently done with the ASPEED GPIO
model, this adds support for inspecting and modifying the PCA9552 LEDs
from the monitor.
(qemu) qom-set /machine/unattached/device[17] led0 on
(qemu) qom-set /machine/unattached/device[17] led0 off
(qemu) qom-set /machine/unattached/device[17] led0 pwm0
(qemu) qom-set /machine/unattached/device[17] led0 pwm1
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-6-clg@kaod.org
[clg: - removed the "qom-get" examples from the commit log
- merged memory leak fixes from Joel ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The overhead for the OpenBMC firmware images using the a custom U-Boot
is around 2 seconds, which is fine, but with a U-Boot from mainline,
it takes an extra 50 seconds or so to reach Linux. A quick survey on
the number of reads performed on the flash memory region gives the
following figures :
OpenBMC U-Boot 922478 (~ 3.5 MBytes)
Mainline U-Boot 20569977 (~ 80 MBytes)
QEMU must be trashing the TCG TBs and reloading text very often. Some
addresses are read more than 250.000 times. Until we find a solution
to improve boot time, execution from MMIO is not activated by default.
Setting this option also breaks migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200114103433.30534-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These buffers should be aligned on 16 bytes.
Ignore invalid RX and TX buffer addresses and log an error. All
incoming and outgoing traffic will be dropped because no valid RX or
TX descriptors will be available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-4-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initialise another SDHCI model instance for the AST2600's eMMC
controller and use the SDHCI's num_slots value introduced previously to
determine whether we should create an SD card instance for the new slot.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-3-clg@kaod.org
[ clg : - removed ternary operator from sdhci_attach_drive()
- renamed SDHCI objects with a '-controller' prefix ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 includes a second cut-down version of the SD/MMC controller
found in the AST2500, named the eMMC controller. It's cut down in the
sense that it only supports one slot rather than two, but it brings the
total number of slots supported by the AST2600 to three.
The existing code assumed that the SD controller always provided two
slots. Rework the SDHCI object to expose the number of slots as a
property to be set by the SoC configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-2-clg@kaod.org
[PMM: fixed up to use device_class_set_props()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The num-lines property of the TYPE_OR_GATE device sets the number
of input lines it has. An assert() in or_irq_realize() restricts
this to the maximum supported by the implementation. However we
got the condition in the assert wrong: it should be using <=,
because num-lines == MAX_OR_LINES is permitted, and means that
all entries from 0 to MAX_OR_LINES-1 in the s->levels[] array
are used.
We didn't notice this previously because no user has so far
needed that many input lines.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200120142235.10432-1-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAl4xgjEACgkQda1lgCoL
QhEmhggA4f2WVC23ub14UHFIqjkfWWDBZ2o+TxttuTNk8aAgSC0lLiPTUgDqB9oC
MINP8rXWB10xTzDPTAgi/C1eWBU0J9YUwGQFCXKTs/wYI2MT7ZVEQxV5kHBJ9Ygg
CjLIjMtDtzY6+gjtxzO1r9o3R+dEgi/ztk9p/EDCBfbERtyE2xqsL/rbhDeM0O2e
h5RVTqharUfvGEmSDWaorTMLcsbNJbx9bYC1PbJ3S9TBnDW6UHcTQ6PL7Rs39dU6
4n9VfE6KtfOwKf+plB8cZlerA9M0HoohsPoRhKPQkMhj1SbxD4jO1zyOuahxGJzY
xjmuJfPtFDTeFntpLNy7t66JYsPItw==
=4iNk
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2020-01-29-1' into staging
Merge tpm 2020/01/29 v1
# gpg: Signature made Wed 29 Jan 2020 13:01:37 GMT
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2020-01-29-1:
tpm-ppi: page-align PPI RAM
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While loading the executable, some platforms (like AVR) need to
detect CPU type that executable is built for - and, with this patch,
this is enabled by reading the field 'e_flags' of the ELF header of
the executable in question. The change expands functionality of
the following functions:
- load_elf()
- load_elf_as()
- load_elf_ram()
- load_elf_ram_sym()
The argument added to these functions is called 'pflags' and is of
type 'uint32_t*' (that matches 'pointer to 'elf_word'', 'elf_word'
being the type of the field 'e_flags', in both 32-bit and 64-bit
variants of ELF header). Callers are allowed to pass NULL as that
argument, and in such case no lookup to the field 'e_flags' will
happen, and no information will be returned, of course.
CC: Richard Henderson <rth@twiddle.net>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Edgar E. Iglesias <edgar.iglesias@gmail.com>
CC: Michael Walle <michael@walle.cc>
CC: Thomas Huth <huth@tuxfamily.org>
CC: Laurent Vivier <laurent@vivier.eu>
CC: Philippe Mathieu-Daudé <f4bug@amsat.org>
CC: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
CC: Aurelien Jarno <aurelien@aurel32.net>
CC: Jia Liu <proljc@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: BALATON Zoltan <balaton@eik.bme.hu>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Artyom Tarasenko <atar4qemu@gmail.com>
CC: Fabien Chouteau <chouteau@adacore.com>
CC: KONRAD Frederic <frederic.konrad@adacore.com>
CC: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1580079311-20447-24-git-send-email-aleksandar.markovic@rt-rk.com>
post-copy migration fails on destination with error such as:
2019-12-26T10:22:44.714644Z qemu-kvm: ram_block_discard_range:
Unaligned start address: 0x559d2afae9a0
Use qemu_memalign() to constrain the PPI RAM memory alignment.
Cc: qemu-stable@nongnu.org
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Message-id: 20200103074000.1006389-3-marcandre.lureau@redhat.com
The commit a718978ed5 from July 2015 introduced the assertion which
implies that the size of successful DMA transfers handled in ide_dma_cb()
should be multiple of 512 (the size of a sector). But guest systems can
initiate DMA transfers that don't fit this requirement.
For fixing that let's check the number of bytes prepared for the transfer
by the prepare_buf() handler. The code in ide_dma_cb() must behave
according to the Programming Interface for Bus Master IDE Controller
(Revision 1.0 5/16/94):
1. If PRDs specified a smaller size than the IDE transfer
size, then the Interrupt and Active bits in the Controller
status register are not set (Error Condition).
2. If the size of the physical memory regions was equal to
the IDE device transfer size, the Interrupt bit in the
Controller status register is set to 1, Active bit is set to 0.
3. If PRDs specified a larger size than the IDE transfer size,
the Interrupt and Active bits in the Controller status register
are both set to 1.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 20191223175117.508990-2-alex.popov@linux.com
Signed-off-by: John Snow <jsnow@redhat.com>
The region in range [0xf0000000 - 0xf1000000] is the PDC area
(Processor Dependent Code), where the firmware is loaded.
This region has higher priority than the main memory.
When the machine has more than 3840MB of RAM, there is an
overlap. Since the PDC is closer to the CPU in the bus
hierarchy, it gets accessed first, and the CPU does not have
access to the RAM in this range.
To model the same behavior and keep a simple memory layout,
reduce the priority of the RAM region. The PDC region ends
overlapping the RAM.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-4-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The hardware expects DIMM slots of 1 or 2 GB, allowing up to
4 GB of memory. We want to accept the same amount of memory the
hardware can deal with. DIMMs of 768MB are not available.
However we have to deal with a firmware limitation: currently
SeaBIOS only supports 32-bit, and expects the RAM size in a
32-bit register. When using a 4GB configuration, the 32-bit
register get truncated and we report a size of 0MB to SeaBIOS,
which ends halting the machine:
$ qemu-system-hppa -m 4g -serial stdio
SeaBIOS: Machine configured with too little memory (0 MB), minimum is 16 MB.
SeaBIOS wants SYSTEM HALT.
The easiest way is to restrict the machine to 3GB of memory.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-3-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The firmware has to reside in the PDC range. If the Elf file
expects to load it below FIRMWARE_START, it is incorrect,
regardless the RAM size.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-2-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This adds emulation of Artist graphics good enough to get a text
console on both Linux and HP-UX. The X11 server from HP-UX also works.
Adjust boot-serial-test to disable graphics, so that SeaBIOS outputs
to the serial port, as expected by the test.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-6-svens@stackframe.org>
[rth: Merge Helge's test for machine->enable_graphics]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Most HP PA-RISC machines have a Digital DS21142/43 Tulip network card,
only some very latest generation machines have an e1000 NIC.
Since qemu now provides an emulated tulip card, use that one instead.
Signed-off-by: Helge Deller <deller@gmx.de>
Message-Id: <20191221222530.GB27803@ls3530.fritz.box>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-5-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
HP-UX sends both the 'Set key make and break (0xfc) and
'Set all key typematic make and break' (0xfa). QEMU response
with 'Resend' as it doesn't handle these commands. HP-UX than
reports an PS/2 max retransmission exceeded error. Add these
commands and just reply with ACK.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-4-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
LASI is a built-in multi-I/O chip which supports serial, parallel,
network (Intel i82596 Apricot), sound and other functionalities.
LASI has been used in many HP PARISC machines.
This patch adds the necessary parts to allow Linux and HP-UX to detect
LASI and the network card.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-3-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The tests of the dino chip with the Online-diagnostics CD
("ODE DINOTEST") now succeeds.
Additionally add some qemu trace events.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191220211512.3289-2-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
While working on the "Enable adapter interruption suppression again"
recently, I had to discover that the meaning of get_machine_class()
and the related *_allowed() wrappers is not very obvious. Add a more
verbose comment here to clarify how these should be used.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200123170256.12386-1-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We currently check (by error) if the passed-in Error pointer errp
is non-null and return after realizing the first child of the
event facility in that case. Symptom is that 'virsh shutdown'
does not work, as the sclpquiesce device is not realized.
Fix this by (correctly) checking the local Error err.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 3d508334dd ("s390x/event-facility: Fix realize() error API violations")
Message-Id: <20200121095506.8537-1-cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If the kernel irqchip has been disabled, we don't want the
{add,release}_adapter_routes routines to call any kvm_irqchip_*
interfaces, as they may rely on an irqchip actually having been
created. Just take a quick exit in that case instead. If you are
trying to use irqfd without a kernel irqchip, we will fail with
an error.
Also initialize routes->gsi[] with -1 in the virtio-ccw handling,
to make sure we don't trip over other errors, either. (Nobody
else uses the gsi array in that structure.)
Fixes: d426d9fba8 ("s390x/virtio-ccw: wire up irq routing and irqfds")
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20200117111147.5006-1-cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
'out' label from write_event_mask() and write_event_data()
can be replaced by 'return'.
The 'out' label from read_event_data() can also be replaced.
However, as suggested by Cornelia Huck, instead of simply
replacing the 'out' label, let's also change the code flow
a bit to make it clearer that sccb events are always handled
regardless of the mask for unconditional reads, while selective
reads are handled if the mask is valid.
CC: Cornelia Huck <cohuck@redhat.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Halil Pasic <pasic@linux.ibm.com>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200108144607.878862-1-danielhb413@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
'out' label can be replaced by 'return' with the appropriate
value that is set by 'r' right before the jump.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200106182425.20312-42-danielhb413@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
'out' label can be replaced by 'return' with the appropriate
value. The 'r' integer, which is used solely to set the
return value for this label, can also be removed.
CC: Cornelia Huck <cohuck@redhat.com>
CC: Halil Pasic <pasic@linux.ibm.com>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200106182425.20312-39-danielhb413@gmail.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
* Cleanups (Philippe)
* virtio-scsi fix (Pan Nengyuan)
* Tweak Skylake-v3 model id (Kashyap)
* x86 UCODE_REV support and nested live migration fix (myself)
* Advisory mode for pvpanic (Zhenwei)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeK1CXAAoJEL/70l94x66DXtkIAI6W5wEY0Yme4M9Q5mGc0RV8
uscPLg0wsg88u6xne8ucCiGymvDREym2ii/aVI0Hi5ish84ZMdCrdck9cd+llpMf
+a3slL26AKlOW8WtYSuyAE1RdLFXngeXdwal5KtWPEExJorkDUPTbwhBzQduQK1a
myoHHcbwdd/96v7FvKnfG8jM6KZtHPQQ0i6+6fX4PN44jaULQNjze8GIrRBEwqw5
uCKJFQPBXiVcxKjH5/kzI1vl2hLJbF2ZGVEzX/U8OPZwyGPHIkWquURo8lvUTPfb
ySlNTUTV2CyrN65TBRXQp/mJi44WvME5Jxlf5rNLBaYXPpL0zhmILKn5X5ya4U0=
=TD0Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Register qdev properties as class properties (Marc-André)
* Cleanups (Philippe)
* virtio-scsi fix (Pan Nengyuan)
* Tweak Skylake-v3 model id (Kashyap)
* x86 UCODE_REV support and nested live migration fix (myself)
* Advisory mode for pvpanic (Zhenwei)
# gpg: Signature made Fri 24 Jan 2020 20:16:23 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (58 commits)
build-sys: clean up flags included in the linker command line
target/i386: Add the 'model-id' for Skylake -v3 CPU models
qdev: use object_property_help()
qapi/qmp: add ObjectPropertyInfo.default-value
qom: introduce object_property_help()
qom: simplify qmp_device_list_properties()
vl: print default value in object help
qdev: register properties as class properties
qdev: move instance properties to class properties
qdev: rename DeviceClass.props
qdev: set properties with device_class_set_props()
object: return self in object_ref()
object: release all props
object: add object_class_property_add_link()
object: express const link with link property
object: add direct link flag
object: rename link "child" to "target"
object: check strong flag with &
object: do not free class properties
object: add object_property_set_default
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use class properties facilities to add properties to the class during
device_class_set_props().
qdev_property_add_static() must be adapted as PropertyInfo now
operates with classes (and not instances), so we must
set_default_value() on the ObjectProperty, before calling its init()
method on the object instance.
Also, PropertyInfo.create() is now exclusively used for class
properties. Fortunately, qdev_property_add_static() is only used in
target/arm/cpu.c so far, which doesn't use "link" properties (that
require create()).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20200110153039.1379601-22-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the one-user function to the place it is being used.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200110153039.1379601-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers use error_abort, and even the function itself calls with
error_abort.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20200110153039.1379601-4-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function is already documented in the header.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20200110153039.1379601-3-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We only access this variable in the RTAS_SYSPARM_SPLPAR_CHARACTERISTICS
case. Use it in place and remove the local declaration.
Suggested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200121110349.25842-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We received a SpaprMachineState argument. Since SpaprMachineState
inherits of MachineState, use it instead of calling qdev_get_machine.
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200121110349.25842-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since we have the MachineState already available locally,
use it instead of the global current_machine.
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200121110349.25842-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use virtio_delete_queue to make it more clear.
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200117075547.60864-3-pannengyuan@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To ease review/modifications of this Makefile, group generic
objects first, then system-mode specific ones, and finally
peripherals (which are only used in system-mode).
No logical changes introduced here.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200118140619.26333-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The user-mode code does not use this API, restrict it
to the system-mode.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200118140619.26333-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't need to explicit this obvious switch fall through.
Stay consistent with the rest of the codebase.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191218192526.13845-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't need to explicit these obvious switch fall through
comments. Stay consistent with the rest of the codebase.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191218192526.13845-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
GCC9 is confused by this comment when building with CFLAG
-Wimplicit-fallthrough=2:
hw/net/imx_fec.c: In function ‘imx_eth_write’:
hw/net/imx_fec.c:906:12: error: this statement may fall through [-Werror=implicit-fallthrough=]
906 | if (unlikely(single_tx_ring)) {
| ^
hw/net/imx_fec.c:912:5: note: here
912 | case ENET_TDAR: /* FALLTHROUGH */
| ^~~~
cc1: all warnings being treated as errors
Rewrite the comments in the correct place, using 'fall through'
which is recognized by GCC and static analyzers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191218192526.13845-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by GCC9 when building with CFLAG -Wimplicit-fallthrough=2:
hw/timer/aspeed_timer.c: In function ‘aspeed_timer_set_value’:
hw/timer/aspeed_timer.c:283:24: error: this statement may fall through [-Werror=implicit-fallthrough=]
283 | if (old_reload || !t->reload) {
| ~~~~~~~~~~~^~~~~~~~~~~~~
hw/timer/aspeed_timer.c:287:5: note: here
287 | case TIMER_REG_STATUS:
| ^~~~
cc1: all warnings being treated as errors
Add the missing fall through comment.
Fixes: 1403f36447
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191218192526.13845-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When building with GCC9 using CFLAG -Wimplicit-fallthrough=2 we get:
hw/display/tcx.c: In function ‘tcx_dac_writel’:
hw/display/tcx.c:453:26: error: this statement may fall through [-Werror=implicit-fallthrough=]
453 | s->dac_index = (s->dac_index + 1) & 0xff; /* Index autoincrement */
| ~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/display/tcx.c:454:9: note: here
454 | default:
| ^~~~~~~
hw/display/tcx.c: In function ‘tcx_dac_readl’:
hw/display/tcx.c:412:22: error: this statement may fall through [-Werror=implicit-fallthrough=]
412 | s->dac_index = (s->dac_index + 1) & 0xff; /* Index autoincrement */
| ~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/display/tcx.c:413:5: note: here
413 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
Give a hint to GCC by adding the missing fall through comments.
Fixes: 55d7bfe22
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20191218192526.13845-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Handle bit 1 write, then post event to monitor.
Suggested by Paolo, declear a new event, using GUEST_PANICKED could
cause upper layers to react by shutting down or rebooting the guest.
In advance for extention, add GuestPanicInformation in event message.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20200114023102.612548-3-pizhenwei@bytedance.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similarly to what we already do with qdev, use a helper to overload the
reset QOM methods of the parent in children classes, for clarity.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <157650847239.354886.2782881118916307978.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch set contains a handful of collected fixes that I'd like to target
for the 5.0 soft freeze (I know that's a long way away, I just don't know what
else to call these):
* A fix for a memory leak initializing the sifive_u board.
* Fixes to privilege mode emulation related to interrupts and fstatus.
Notably absent is the H extension implementation. That's pretty much reviewed,
but not quite ready to go yet and I didn't want to hold back these important
fixes. This boots 32-bit and 64-bit Linux (buildroot this time, just for fun)
and passes "make check".
-----BEGIN PGP SIGNATURE-----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=WooQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-5.0-sf1' into staging
RISC-V Patches for the 5.0 Soft Freeze, Part 1
This patch set contains a handful of collected fixes that I'd like to target
for the 5.0 soft freeze (I know that's a long way away, I just don't know what
else to call these):
* A fix for a memory leak initializing the sifive_u board.
* Fixes to privilege mode emulation related to interrupts and fstatus.
Notably absent is the H extension implementation. That's pretty much reviewed,
but not quite ready to go yet and I didn't want to hold back these important
fixes. This boots 32-bit and 64-bit Linux (buildroot this time, just for fun)
and passes "make check".
# gpg: Signature made Tue 21 Jan 2020 22:55:28 GMT
# gpg: using RSA key 2B3C3747446843B24A943A7A2E1319F35FBB1889
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmerdabbelt@google.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
# Subkey fingerprint: 2B3C 3747 4468 43B2 4A94 3A7A 2E13 19F3 5FBB 1889
* remotes/palmer/tags/riscv-for-master-5.0-sf1:
target/riscv: update mstatus.SD when FS is set dirty
target/riscv: fsd/fsw doesn't dirty FP state
target/riscv: Fix tb->flags FS status
riscv: Set xPIE to 1 after xRET
riscv/sifive_u: fix a memory leak in soc_realize()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Import our virtiofsd.
This pulls in the daemon to drive a file system connected to the
existing qemu virtiofsd device.
It's derived from upstream libfuse with lots of changes (and a lot
trimmed out).
The daemon lives in the newly created qemu/tools/virtiofsd
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
v2
drop the docs while we discuss where they should live
and we need to redo the manpage in anything but texi
-----BEGIN PGP SIGNATURE-----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=UUVN
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert-gitlab/tags/pull-virtiofs-20200123b' into staging
virtiofsd first pull v2
Import our virtiofsd.
This pulls in the daemon to drive a file system connected to the
existing qemu virtiofsd device.
It's derived from upstream libfuse with lots of changes (and a lot
trimmed out).
The daemon lives in the newly created qemu/tools/virtiofsd
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
v2
drop the docs while we discuss where they should live
and we need to redo the manpage in anything but texi
# gpg: Signature made Thu 23 Jan 2020 16:45:18 GMT
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert-gitlab/tags/pull-virtiofs-20200123b: (108 commits)
virtiofsd: add some options to the help message
virtiofsd: stop all queue threads on exit in virtio_loop()
virtiofsd/passthrough_ll: Pass errno to fuse_reply_err()
virtiofsd: Convert lo_destroy to take the lo->mutex lock itself
virtiofsd: add --thread-pool-size=NUM option
virtiofsd: fix lo_destroy() resource leaks
virtiofsd: prevent FUSE_INIT/FUSE_DESTROY races
virtiofsd: process requests in a thread pool
virtiofsd: use fuse_buf_writev to replace fuse_buf_write for better performance
virtiofsd: add definition of fuse_buf_writev()
virtiofsd: passthrough_ll: Use cache_readdir for directory open
virtiofsd: Fix data corruption with O_APPEND write in writeback mode
virtiofsd: Reset O_DIRECT flag during file open
virtiofsd: convert more fprintf and perror to use fuse log infra
virtiofsd: do not always set FUSE_FLOCK_LOCKS
virtiofsd: introduce inode refcount to prevent use-after-free
virtiofsd: passthrough_ll: fix refcounting on remove/rename
libvhost-user: Fix some memtable remap cases
virtiofsd: rename inode->refcount to inode->nlookup
virtiofsd: prevent races with lo_dirp_put()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we receive an unexpected message type on the slave fd, print
the type.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The Exynos4210 serial driver uses an interrupt line to signal if receive
data is available. Connect that interrupt with the DMA controller's
'peripheral busy' gpio pin to stop the DMA if there is no more receive
data available. Without this patch, receive DMA runs wild and fills the
entire receive DMA buffer with invalid data.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200123052540.6132-9-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To support receive DMA, we need to inform the DMA controller if receive data
is available. Otherwise the DMA controller keeps requesting data, causing
receive errors.
Implement this using an interrupt line. The instantiating code then needs
to connect the interrupt with the matching DMA controller GPIO pin.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200123052540.6132-8-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The driver already implements a receive FIFO, but it does not
handle receive FIFO trigger levels and timeout. Implement the
missing functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200123052540.6132-7-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
After restoring a VM, serial parameters need to be updated to reflect
restored register values. Implement a post_load function to handle this
situation.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200123052540.6132-6-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace debug code with tracing to aid debugging.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200123052540.6132-5-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
First parameter to exynos4210_get_irq() is not the SPI port number,
but the interrupt group number. Interrupt groups are 20 for mdma
and 21 for pdma. Interrupts are not inverted. Controllers support 32
events (pdma) or 31 events (mdma). Events must all be routed to a single
interrupt line. Set other parameters as documented in Exynos4210 datasheet,
section 8 (DMA controller).
Fixes: 59520dc65e ("hw/arm/exynos4210: Add DMA support for the Exynos4210")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200123052540.6132-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Missed in 870c034da0, hopefully reported by Coverity.
Fixes: Coverity CID 1412793 (Incorrect expression)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20200121213853.9601-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can use existing helper function to trigger hotplug handler
plug, which makes code clearer.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Message-id: 20200120012755.44581-3-zhukeqian1@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is extra indent in ACPI GED hotplug cb that should be
deleted.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Message-id: 20200120012755.44581-2-zhukeqian1@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop a trailing whitespace. Make line shorter.
Fixes: 7652511473 ("vhost: Only align sections for vhost-user")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per the ACPI spec (version 6.1, section 6.1.5 _HID) it is not required
on enumerated buses (like PCI in this case), _ADR is required (and is
already there). And the _HID value is wrong. Linux appears to ignore
the _HID entry, but Windows 10 detects it as 'Unknown Device' and there
is no driver available. See https://bugs.launchpad.net/qemu/+bug/1856724
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200120170725.24935-6-minyard@acm.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I added hugepage alignment code in c1ece84e7c to deal with
vhost-user + postcopy which needs aligned pages when using userfault.
However, on x86 the lower 2MB of address space tends to be shotgun'd
with small fragments around the 512-640k range - e.g. video RAM, and
with HyperV synic pages tend to sit around there - again splitting
it up. The alignment code complains with a 'Section rounded to ...'
error and gives up.
Since vhost-user already filters out devices without an fd
(see vhost-user.c vhost_user_mem_section_filter) it shouldn't be
affected by those overlaps.
Turn the alignment off on vhost-kernel so that it doesn't try
and align, and thus won't hit the rounding issues.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200116202414.157959-3-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Add the memory region names to section rounding/alignment
warnings.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200116202414.157959-2-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Receive/transmit/event vqs forgot to cleanup in vhost_vsock_unrealize. This
patch save receive/transmit vq pointer in realize() and cleanup vqs
through those vq pointers in unrealize(). The leak stack is as follow:
Direct leak of 21504 byte(s) in 3 object(s) allocated from:
#0 0x7f86a1356970 (/lib64/libasan.so.5+0xef970) ??:?
#1 0x7f86a09aa49d (/lib64/libglib-2.0.so.0+0x5249d) ??:?
#2 0x5604852f85ca (./x86_64-softmmu/qemu-system-x86_64+0x2c3e5ca) /mnt/sdb/qemu/hw/virtio/virtio.c:2333
#3 0x560485356208 (./x86_64-softmmu/qemu-system-x86_64+0x2c9c208) /mnt/sdb/qemu/hw/virtio/vhost-vsock.c:339
#4 0x560485305a17 (./x86_64-softmmu/qemu-system-x86_64+0x2c4ba17) /mnt/sdb/qemu/hw/virtio/virtio.c:3531
#5 0x5604858e6b65 (./x86_64-softmmu/qemu-system-x86_64+0x322cb65) /mnt/sdb/qemu/hw/core/qdev.c:865
#6 0x5604861e6c41 (./x86_64-softmmu/qemu-system-x86_64+0x3b2cc41) /mnt/sdb/qemu/qom/object.c:2102
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-Id: <20200115062535.50644-1-pannengyuan@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use virtio_delete_queue to make it more clear.
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-Id: <20200117075547.60864-3-pannengyuan@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Use virtio_delete_queue to make it more clear.
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-Id: <20200117060927.51996-3-pannengyuan@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
v->vq forgot to cleanup in virtio_9p_device_unrealize, the memory leak
stack is as follow:
Direct leak of 14336 byte(s) in 2 object(s) allocated from:
#0 0x7f819ae43970 (/lib64/libasan.so.5+0xef970) ??:?
#1 0x7f819872f49d (/lib64/libglib-2.0.so.0+0x5249d) ??:?
#2 0x55a3a58da624 (./x86_64-softmmu/qemu-system-x86_64+0x2c14624) /mnt/sdb/qemu/hw/virtio/virtio.c:2327
#3 0x55a3a571bac7 (./x86_64-softmmu/qemu-system-x86_64+0x2a55ac7) /mnt/sdb/qemu/hw/9pfs/virtio-9p-device.c:209
#4 0x55a3a58e7bc6 (./x86_64-softmmu/qemu-system-x86_64+0x2c21bc6) /mnt/sdb/qemu/hw/virtio/virtio.c:3504
#5 0x55a3a5ebfb37 (./x86_64-softmmu/qemu-system-x86_64+0x31f9b37) /mnt/sdb/qemu/hw/core/qdev.c:876
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-Id: <20200117060927.51996-2-pannengyuan@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Acked-by: Greg Kurz <groug@kaod.org>
Firmware can enumerate present at boot APs by broadcasting wakeup IPI,
so that woken up secondary CPUs could register them-selves.
However in CPU hotplug case, it would need to know architecture
specific CPU IDs for possible and hotplugged CPUs so it could
prepare environment for and wake hotplugged AP.
Reuse and extend existing CPU hotplug interface to return architecture
specific ID for currently selected CPU in 2 registers:
- lower 32 bits in ACPI_CPU_CMD_DATA_OFFSET_RW
- upper 32 bits in ACPI_CPU_CMD_DATA2_OFFSET_R
On x86, firmware will use CPHP_GET_CPU_ID_CMD for fetching the APIC ID
when handling hotplug SMI.
Later, CPHP_GET_CPU_ID_CMD will be used on ARM to retrieve MPIDR,
which serves the similar to APIC ID purpose.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1575896942-331151-10-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
No functional change in practice, patch only aims to properly
document (in spec and code) intended usage of the reserved space.
The new field is to be used for 2 purposes:
- detection of modern CPU hotplug interface using
CPHP_GET_NEXT_CPU_WITH_EVENT_CMD command.
procedure will be described in follow up patch:
"acpi: cpuhp: spec: add typical usecases"
- for returning upper 32 bits of architecture specific CPU ID,
for new CPHP_GET_CPU_ID_CMD command added by follow up patch:
"acpi: cpuhp: add CPHP_GET_CPU_ID_CMD command"
Change is backward compatible with 4.2 and older machines, as field was
unconditionally reserved and always returned 0x0 if modern CPU hotplug
interface was enabled.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1575896942-331151-8-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
It's not what real HW does, implementing which would be overkill [**]
and would require complex cross stack changes (QEMU+firmware) to make
it work.
So considering that SMRAM is owned by MCH, for simplicity (ab)use
reserved Q35 register, which allows QEMU and firmware easily init
and make RAM at SMBASE available only from SMM context.
Patch uses commit (2f295167e0 q35/mch: implement extended TSEG sizes)
for inspiration and uses reserved register in config space at 0x9c
offset [*] to extend q35 pci-host with ability to use 128K at
0x30000 as SMRAM and hide it (like TSEG) from non-SMM context.
Usage:
1: write 0xff in the register
2: if the feature is supported, follow up read from the register
should return 0x01. At this point RAM at 0x30000 is still
available for SMI handler configuration from non-SMM context
3: writing 0x02 in the register, locks SMBASE area, making its contents
available only from SMM context. In non-SMM context, reads return
0xff and writes are ignored. Further writes into the register are
ignored until the system reset.
*) https://www.mail-archive.com/qemu-devel@nongnu.org/msg455991.html
**) https://www.mail-archive.com/qemu-devel@nongnu.org/msg646965.html
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1575896942-331151-3-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
'out' label in v9fs_xattr_write() and 'out_nofid' label in
v9fs_complete_rename() can be replaced by appropriate return
calls.
CC: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
init_in_iov_from_pdu might not be able to allocate the full buffer size
requested, which comes from the client and could be larger than the
transport has available at the time of the request. Specifically, this
can happen with read operations, with the client requesting a read up to
the max allowed, which might be more than the transport has available at
the time.
Today the implementation of init_in_iov_from_pdu throws an error, both
Xen and Virtio.
Instead, change the V9fsTransport interface so that the size becomes a
pointer and can be limited by the implementation of
init_in_iov_from_pdu.
Change both the Xen and Virtio implementations to set the size to the
size of the buffer they managed to allocate, instead of throwing an
error. However, if the allocated buffer size is less than P9_IOHDRSZ
(the size of the header) still throw an error as the case is unhandable.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
CC: groug@kaod.org
CC: anthony.perard@citrix.com
CC: roman@zededa.com
CC: qemu_oss@crudebyte.com
[groug: fix 32-bit build]
Signed-off-by: Greg Kurz <groug@kaod.org>
local_unlinkat_common() is supposed to always return -1 on error.
This is being done by jumps to the 'err_out' label, which is
a 'return ret' call, and 'ret' is initialized with -1.
Unfortunately there is a condition in which the function will
return 0 on error: in a case where flags == AT_REMOVEDIR, 'ret'
will be 0 when reaching
map_dirfd = openat_dir(...)
And, if map_dirfd == -1 and errno != ENOENT, the existing 'err_out'
jump will execute 'return ret', when ret is still set to zero
at that point.
This patch fixes it by changing all 'err_out' labels by
'return -1' calls, ensuring that the function will always
return -1 on error conditions. 'ret' can be left unintialized
since it's now being used just to store the result of 'unlinkat'
calls.
CC: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
[groug: changed prefix in title to be "9p: local:"]
Signed-off-by: Greg Kurz <groug@kaod.org>
There is a possible memory leak while local_link return -1 without free
odirpath and oname.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Jaijun Chen <chenjiajun8@huawei.com>
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Migration is silently broken now with x2apic config like this:
-smp 200,maxcpus=288,sockets=2,cores=72,threads=2 \
-device intel-iommu,intremap=on,eim=on
After migration, the guest kernel could hang at anything, due to
x2apic bit not migrated correctly in IA32_APIC_BASE on some vcpus, so
any operations related to x2apic could be broken then (e.g., RDMSR on
x2apic MSRs could fail because KVM would think that the vcpu hasn't
enabled x2apic at all).
The issue is that the x2apic bit was never applied correctly for vcpus
whose ID > 255 when migrate completes, and that's because when we
migrate APIC we use the APICCommonState.id as instance ID of the
migration stream, while that's too short for x2apic.
Let's use the newly introduced initial_apic_id for that.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It was always used as 32bit, so define it as used to be clear.
Instead of using -1 as the auto-gen magic value, we switch to
UINT32_MAX. We also make sure that we don't auto-gen this value to
avoid overflowed instance IDs without being noticed.
Suggested-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Define the new macro VMSTATE_INSTANCE_ID_ANY for callers who wants to
auto-generate the vmstate instance ID. Previously it was hard coded
as -1 instead of this macro. It helps to change this default value in
the follow up patches. No functional change.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The IAR0/IAR1 register is used to acknowledge an interrupt - a read of the
register activates the highest priority pending interrupt and provides its
interrupt ID. Activating an interrupt can change the CPU's virtual interrupt
state - this change makes sure the virtual irq state is updated.
Signed-off-by: Jeff Kubascik <jeff.kubascik@dornerworks.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200113154607.97032-1-jeff.kubascik@dornerworks.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an emulation for the RNGC random number generator and the compatible
RNGB variant. These peripherals are included (at least) in imx25 and
imx35 chipsets.
The emulation supports the initial self test, reseeding the prng and
reading random numbers.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We won't reuse the CPU IRQ/FIQ variables. Simplify by calling
qdev_get_gpio_in() in place.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191230110953.25496-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
By calling qdev_pass_gpios() we don't need to hold a copy of the
IRQs from the INTC into the SoC state.
Instead of filling an array of qemu_irq and passing it around, we
can now directly call qdev_get_gpio_in() on the SoC.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191230110953.25496-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
These definitions are specific to the A10 SoC and don't need
to be exported to the different Allwinner peripherals.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191230110953.25496-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ef941d59fd8658589d34ed432e1d6dfdcf7fb1d0.1576658572.git.alistair@alistair23.me
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix a minor memory leak in riscv_sifive_u_soc_realize()
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Factor out slot status check into a helper function. Add an additional
check after completing transfers. This is needed in case a guest
queues multiple transfers in a row and a device unplug happens while
qemu processes them.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1786413
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200107083606.12393-1-kraxel@redhat.com
start vm with libvirt, when GuestOS running, enter poweroff command using
the xhci keyboard, then ASAN shows memory leak stack：
Direct leak of 80 byte(s) in 5 object(s) allocated from:
#0 0xfffd1e6431cb in __interceptor_malloc (/lib64/libasan.so.4+0xd31cb)
#1 0xfffd1e107163 in g_malloc (/lib64/libglib-2.0.so.0+0x57163)
#2 0xaaad39051367 in qemu_sglist_init /qemu/dma-helpers.c:43
#3 0xaaad3947c407 in pci_dma_sglist_init /qemu/include/hw/pci/pci.h:842
#4 0xaaad3947c407 in xhci_xfer_create_sgl /qemu/hw/usb/hcd-xhci.c:1446
#5 0xaaad3947c407 in xhci_setup_packet /qemu/hw/usb/hcd-xhci.c:1618
#6 0xaaad3948625f in xhci_submit /qemu/hw/usb/hcd-xhci.c:1827
#7 0xaaad3948625f in xhci_fire_transfer /qemu/hw/usb/hcd-xhci.c:1839
#8 0xaaad3948625f in xhci_kick_epctx /qemu/hw/usb/hcd-xhci.c:1991
#9 0xaaad3948f537 in xhci_doorbell_write /qemu/hw/usb/hcd-xhci.c:3158
#10 0xaaad38bcbfc7 in memory_region_write_accessor /qemu/memory.c:483
#11 0xaaad38bc654f in access_with_adjusted_size /qemu/memory.c:544
#12 0xaaad38bd1877 in memory_region_dispatch_write /qemu/memory.c:1482
#13 0xaaad38b1c77f in flatview_write_continue /qemu/exec.c:3167
#14 0xaaad38b1ca83 in flatview_write /qemu/exec.c:3207
#15 0xaaad38b268db in address_space_write /qemu/exec.c:3297
#16 0xaaad38bf909b in kvm_cpu_exec /qemu/accel/kvm/kvm-all.c:2383
#17 0xaaad38bb063f in qemu_kvm_cpu_thread_fn /qemu/cpus.c:1246
#18 0xaaad39821c93 in qemu_thread_start /qemu/util/qemu-thread-posix.c:519
#19 0xfffd1c8378bb (/lib64/libpthread.so.0+0x78bb)
#20 0xfffd1c77616b (/lib64/libc.so.6+0xd616b)
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Message-id: 20200110105855.81144-1-kuhn.chenqun@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
I've got a case where usbredir_write manages to call back into itself
via spice; this patch causes the recursion to fail (0 bytes) the write;
this seems to avoid the deadlock I was previously seeing.
I can't say I fully understand the interaction of usbredir and spice;
but there are a few similar guards in spice and usbredir
to catch other cases especially onces also related to spice_server_char_device_wakeup
This case seems to be triggered by repeated migration+repeated
reconnection of the viewer; but my debugging suggests the migration
finished before this hits.
The backtrace of the hang looks like:
reds_handle_ticket
reds_handle_other_links
reds_channel_do_link
red_channel_connect
spicevmc_connect
usbredir_create_parser
usbredirparser_do_write
usbredir_write
qemu_chr_fe_write
qemu_chr_write
qemu_chr_write_buffer
spice_chr_write
spice_server_char_device_wakeup
red_char_device_wakeup
red_char_device_write_to_device
vmc_write
usbredirparser_do_write
usbredir_write
qemu_chr_fe_write
qemu_chr_write
qemu_chr_write_buffer
qemu_mutex_lock_impl
and we fail as we lang through qemu_chr_write_buffer's lock
twice.
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1752320
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20191218113012.13331-1-dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If the redirected device has this capability, Windows guest may
place the device into D2 and expect it to wake when the device
becomes active, but this will never happen. For example, when
internal Bluetooth adapter is redirected, keyboards and mice
connected to it do not work. Current commit removes this
capability (starting from machine 5.0)
Set 'usb-redir.suppress-remote-wake' property to 'off' to keep
'remote wake' as is or to 'on' to remove 'remote wake' on
4.2 or earlier.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-id: 20200108091044.18055-3-yuri.benditovich@daynix.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If the redirected device has this capability, Windows guest may
place the device into D2 and expect it to wake when the device
becomes active, but this will never happen. For example, when
internal Bluetooth adapter is redirected, keyboards and mice
connected to it do not work. Current commit removes this
capability (starting from machine 5.0)
Set 'usb-host.suppress-remote-wake' property to 'off' to keep
'remote wake' as is or to 'on' to remove 'remote wake' on
4.2 or earlier.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-id: 20200108091044.18055-2-yuri.benditovich@daynix.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* Command line parsing fixes (Michal, Peter, Xiaoyao)
* Cooperlake CPU model fixes (Xiaoyao)
* i386 gdb fix (mkdolata)
* IOEventHandler cleanup (Philippe)
* icount fix (Pavel)
* RR support for random number sources (Pavel)
* Kconfig fixes (Philippe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeFbG8AAoJEL/70l94x66DCpMIAKBwxBL+VegqI+ySKgmtIBQX
LtU+ardEeZ37VfWfvuWzTFe+zQ0hsFpz/e0LHE7Ae+LVLMNWXixlmMrTIm+Xs762
hJzxBjhUhkdrMioVYTY16Kqap4Nqaxu70gDQ32Ve2sY6xYGxYLSaJooBOU5bXVgb
HPspHFVpeP6ZshBd1n2LXsgURE6v3AjTwqcsPCkL/AESFdkdOsoHeXjyKWJG1oPy
W7btzlUEqVsauZI8/PhhW/8hZUvUsJVHonYLTZTyy8aklU7aOILSyT2uPXFBVUVQ
irkQjLtD4dWlogBKO4i/QHMuwV+Asa57WNPmqv3EcIWPUWmTY84H0g2AxRgcc2M=
=48jx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Compat machines fix (Denis)
* Command line parsing fixes (Michal, Peter, Xiaoyao)
* Cooperlake CPU model fixes (Xiaoyao)
* i386 gdb fix (mkdolata)
* IOEventHandler cleanup (Philippe)
* icount fix (Pavel)
* RR support for random number sources (Pavel)
* Kconfig fixes (Philippe)
# gpg: Signature made Wed 08 Jan 2020 10:41:00 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (38 commits)
chardev: Use QEMUChrEvent enum in IOEventHandler typedef
chardev: use QEMUChrEvent instead of int
chardev/char: Explicit we ignore some QEMUChrEvent in IOEventHandler
monitor/hmp: Explicit we ignore a QEMUChrEvent in IOEventHandler
monitor/qmp: Explicit we ignore few QEMUChrEvent in IOEventHandler
virtio-console: Explicit we ignore some QEMUChrEvent in IOEventHandler
vhost-user-blk: Explicit we ignore few QEMUChrEvent in IOEventHandler
vhost-user-net: Explicit we ignore few QEMUChrEvent in IOEventHandler
vhost-user-crypto: Explicit we ignore some QEMUChrEvent in IOEventHandler
ccid-card-passthru: Explicit we ignore QEMUChrEvent in IOEventHandler
hw/usb/redirect: Explicit we ignore few QEMUChrEvent in IOEventHandler
hw/usb/dev-serial: Explicit we ignore few QEMUChrEvent in IOEventHandler
hw/char/terminal3270: Explicit ignored QEMUChrEvent in IOEventHandler
hw/ipmi: Explicit we ignore some QEMUChrEvent in IOEventHandler
hw/ipmi: Remove unnecessary declarations
target/i386: Add missed features to Cooperlake CPU model
target/i386: Add new bit definitions of MSR_IA32_ARCH_CAPABILITIES
target/i386: Fix handling of k_gs_base register in 32-bit mode in gdbstub
hw/rtc/mc146818: Add missing dependency on ISA Bus
hw/nvram/Kconfig: Restrict CHRP NVRAM to machines using OpenBIOS or SLOF
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's another pull request for qemu-5.0 of ppc related changes.
Highlights are:
* First parts of support for POWER Secure VMs
* Rework to clean up how we pass context information to the various
components of the pnv machine (reduces usage of qdev_get_machine())
* Assorted cleanups and bugfixes
-----BEGIN PGP SIGNATURE-----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=gbsd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.0-20200108' into staging
ppc patch queue 2020-01-08
Here's another pull request for qemu-5.0 of ppc related changes.
Highlights are:
* First parts of support for POWER Secure VMs
* Rework to clean up how we pass context information to the various
components of the pnv machine (reduces usage of qdev_get_machine())
* Assorted cleanups and bugfixes
# gpg: Signature made Wed 08 Jan 2020 05:22:08 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.0-20200108: (26 commits)
ppc/pnv: fix check on return value of blk_getlength()
ppc/pnv: check return value of blk_pwrite()
pnv/psi: Consolidate some duplicated code in pnv_psi_realize()
pnv/psi: Add device reset hook
pnv/xive: Deduce the PnvXive pointer from XiveTCTX::xptr
spapr/xive: Deduce the SpaprXive pointer from XiveTCTX::xptr
xive: Add a "presenter" link property to the TCTX object
ppc/pnv: Add a "pnor" const link property to the BMC internal simulator
ppc/pnv: Add an "nr-threads" property to the base chip class
xive: Use the XIVE fabric link under the XIVE router
spapr, pnv, xive: Add a "xive-fabric" link to the XIVE router
pnv/xive: Use device_class_set_parent_realize()
ppc/pnv: Introduce a "xics" property under the POWER8 chip
ppc/pnv: Introduce a "xics" property alias under the PSI model
spapr/xive: remove redundant check in spapr_match_nvt()
ppc/pnv: Drop "num-chips" machine property
ppc440_bamboo.c: remove label from bamboo_load_device_tree()
spapr.c: remove 'out' label in spapr_dt_cas_updates()
ppc/spapr: Don't call KVM_SVM_OFF ioctl on TCG
spapr/xive: Use device_class_set_parent_realize()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- build fix (missing x86-iommu stubs)
- python fixes for freebsd and OSX
- nicer reporting of acceptance failures
- fix build nesting of fp-test (breaks bsds)
- semihosting clean-ups
- support for blocking semihosting console
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl4XEbsACgkQ+9DbCVqe
KkRtOwgAkdw3Pwi6sSlKdouR0lcWsRRqY2T3nA+xM/JrS+W9+hJ3VsM7EcBCJZcJ
juJkQs3kU7Gs3LAeKbjmNq9xj9eTElD20l23RufiNB2CgULwHJ2+skGCTCq+1T1P
VBWWNky4RyGjgcKoQQ8cNUmFhntnemGjnxvz1G0dObPu6yl5jNXIk7qJFZkSsERy
YptCN8AF2bLXekYiB9Zn0xRd+O5Q4u/RtOg62REZoZOTA11M2Zuy+fkRK4XSzM/I
wVdRd0t0hKViktl3Z4iu3MsQqCxaHIirsfEMVkmbGWMmepq3db9Xs1k4Ss2I7Uo3
YRTxj1BCwynsGbDpWSI/XHOYgKp8rA==
=lSAv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-semihosting-090120-2' into staging
Testing fixes and semiconsole support:
- build fix (missing x86-iommu stubs)
- python fixes for freebsd and OSX
- nicer reporting of acceptance failures
- fix build nesting of fp-test (breaks bsds)
- semihosting clean-ups
- support for blocking semihosting console
# gpg: Signature made Thu 09 Jan 2020 11:42:51 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-semihosting-090120-2:
tests/tcg: add user version of dumb-as-bricks semiconsole test
tests/tcg: extract __semi_call into a header and expand
tests/tcg: add a dumb-as-bricks semihosting console test
semihosting: add qemu_semihosting_console_inc for SYS_READC
target/arm: only update pc after semihosting completes
target/arm: remove unused EXCP_SEMIHOST leg
testing: don't nest build for fp-test
travis.yml: install homebrew python for OS X
travis.yml: duplicate before_script for MacOSX
travis.yml: Detach build and test steps
travis.yml: avocado: Print logs of non-pass tests only
freebsd: use python37
tests/vm: update openbsd to release 6.6
hw/i386/x86-iommu: Add missing stubs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provides a blocking call to read a character from the console using
semihosting.chardev, if specified. This takes some careful command
line options to use stdio successfully as the serial ports, monitor
and semihost all want to use stdio. Here's a sample set of command
line options which share stdio between semihost, monitor and serial
ports:
qemu \
-chardev stdio,mux=on,id=stdio0 \
-serial chardev:stdio0 \
-semihosting-config enable=on,chardev=stdio0 \
-mon chardev=stdio0,mode=readline
This creates a chardev hooked to stdio and then connects all of the
subsystems to it. A shorter mechanism would be good to hear about.
Signed-off-by: Keith Packard <keithp@keithp.com>
Message-Id: <20191104204230.12249-1-keithp@keithp.com>
[AJB: fixed up deadlock, minor commit title reword]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
In commit 6c730e4af9 we introduced a stub to build the MicroVM
machine without Intel IOMMU. This stub is incomplete for the
other PC machines. Add the missing stubs.
Fixes: 6c730e4af9
Reported-by: Travis-CI
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20191220154225.25879-1-philmd@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum.
By using the enum in the IOEventHandler typedef we:
- make the IOEventHandler type more explicit (this handler
process out-of-band information, while the IOReadHandler
is in-band),
- help static code analyzers.
This patch was produced with the following spatch script:
@match@
expression backend, opaque, context, set_open;
identifier fd_can_read, fd_read, fd_event, be_change;
@@
qemu_chr_fe_set_handlers(backend, fd_can_read, fd_read, fd_event,
be_change, opaque, context, set_open);
@depends on match@
identifier opaque, event;
identifier match.fd_event;
@@
static
-void fd_event(void *opaque, int event)
+void fd_event(void *opaque, QEMUChrEvent event)
{
...
}
Then the typedef was modified manually in
include/chardev/char-fe.h.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-15-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
blk_getlength() returns an int64_t but the result is stored in a
uint32_t. Errors (negative values) won't be caught by the check in
pnv_pnor_realize() and blk_blockalign() will allocate a very large
buffer in such cases.
Fixes Coverity issue CID 1412226.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200107171809.15556-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When updating the PNOR file contents, we should check for a possible
failure of blk_pwrite().
Fixes Coverity issue CID 1412228.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200107171809.15556-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The proper way to do that would be to use device_class_set_parent_realize(),
but defining a Pnv8PsiClass and a Pnv9PsiClass types with a parent_realize
pointer adds a fair amount of code. Calling pnv_psi_realize() explicitely
is fine for now.
This should probably be achieved with a device realize hook in the
PSI base class and device_class_set_parent_realize() in the children
classes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <157841476667.66386.13659183399113837990.stgit@bahia.tlslab.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And call it from a QEMU reset handler. This allows each PNV child class to
override the reset hook if needed, eg. POWER8 doesn't but POWER9 does.
The proper way to do that would be to use device_class_set_parent_reset(),
but defining a Pnv8PsiClass and a Pnv9PsiClass types with a parent_reset
pointer adds a fair amount of code. Calling pnv_psi_reset() explicitely is
fine for now.
A subsequent patch will consolidate the call to qemu_register_reset() in
a single place.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <157841476035.66386.17838417527621752518.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And use it instead of reaching out to the machine. This allows to get
rid of pnv_get_chip().
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And use it instead of reaching out to the machine. This allows to get rid
of a call to qdev_get_machine() and to reduce the scope of another one so
that it is only used within the argument list of error_append_hint(). This
is an acceptable tradeoff compared to all it would require to know about
the maximum number of CPUs here without calling qdev_get_machine().
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used in subsequent patches to access the XIVE associated to
a TCTX without reaching out to the machine through qdev_get_machine().
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[ groug: - split patch
- write subject and changelog ]
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows to get rid of a call to qdev_get_machine().
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Set it at chip creation and forward it to the cores. This allows to drop
a call to qdev_get_machine().
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200106145645.4539-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the spapr and pnv machines do set the "xive-fabric" link, the
use of the XIVE fabric pointer becomes mandatory. This is checked with
an assert() in a new realize hook. Since the XIVE router is realized at
machine init for the all the machine's life time, no risk to abort an
already running guest (ie. not a hotplug path).
This gets rid of a qdev_get_machine() call.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to get rid of qdev_get_machine(), first add a pointer to the
XIVE fabric under the XIVE router and make it configurable through a
QOM link property.
Configure it in the spapr and pnv machine. In the case of pnv, the XIVE
routers are under the chip, so this is done with a QOM alias property of
the POWER9 pnv chip.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE router base class currently inherits an empty realize hook
from the sysbus device base class, but it will soon implement one
of its own to perform some sanity checks. Do the preliminary plumbing
to have it called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200106145645.4539-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
POWER8 is the only chip using the XICS interface. Add a "xics" link
and a XICSFabric attribute under this chip to remove the use of
qdev_get_machine()
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200106145645.4539-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This removes the need of the intermediate link under PSI to pass the
XICS link to the underlying ICSState object.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200106145645.4539-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_match_nvt() is a XIVE operation and is used by the machine to
look for a matching target when an event notification is being
delivered. An assert checks that spapr_match_nvt() is called only when
the machine has selected the XIVE interrupt mode but it is redundant
with the XIVE_PRESENTER() dynamic cast.
Apply the cast to spapr->active_intc and remove the assert.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106163207.4608-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The number of CPU chips of the powernv machine is configurable through a
"num-chips" property. This doesn't fit well with the CPU topology, eg.
some configurations can come up with more CPUs than the maximum of CPUs
set in the toplogy. This causes assertion to be hit with mttcg:
-machine powernv,num-chips=2 -smp cores=2 -accel tcg,thread=multi
ERROR:
tcg/tcg.c:789:tcg_register_thread: assertion failed: (n < ms->smp.max_cpus)
Aborted (core dumped)
Mttcg mandates the CPU topology to be dimensioned to the actual number
of CPUs, depending on the number of chips the user asked for. That is,
'-machine num-chips=N' should always have a '-smp' companion with a
topology that meats the resulting number of CPUs, typically
'-smp sockets=N'.
It thus seems that "num-chips" doesn't bring anything but forcing the user
to specify the requested number of chips on the command line twice. Simplify
the command line by computing the number of chips based on the CPU topology
exclusively. The powernv machine isn't a production thing ; it is mostly
used by developpers to prepare the bringup of real HW. Because of this and
for simplicity, this deliberately ignores the official deprecation process
and dumps "num-chips" right away : '-smp sockets=N' is now the only way to
control the number of CPU chips.
This is done at machine init because smp_parse() is called after instance
init.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157830658266.533764.2214183961444213947.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
'out' label can be replaced by 'return -1' in all cases.
CC: David Gibson <david@gibson.dropbear.id.au>
CC: qemu-ppc@nongnu.org
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200106182425.20312-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
'out' can be replaced by 'return' with the appropriate
return value.
CC: David Gibson <david@gibson.dropbear.id.au>
CC: qemu-ppc@nongnu.org
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200106182425.20312-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE router base class currently inherits an empty realize hook
from the sysbus device base class, but it will soon implement one
of its own to perform some sanity checks. Do the preliminary plumbing
to have it called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191219181155.32530-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Register addr 1 is defined as buffer A with handshake (vBufAH),
register addr 15 is also defined as buffer A without handshake (vBufA).
As both addresses access the same register, remove the definition of
'anh' and use only 'a' (with VIA_REG_ANH and VIA_REG_A).
Fixes: 51f233ec92 ("misc: introduce new mos6522 VIA device and enable it for ppc builds")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20191220214054.76525-1-laurent@vivier.eu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Use container_of() instead of qdev_get_machine()
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191219181155.32530-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A pseries guest can be run as a secure guest on Ultravisor-enabled
POWER platforms. When such a secure guest is reset, we need to
release/reset a few resources both on ultravisor and hypervisor side.
This is achieved by invoking this new ioctl KVM_PPC_SVM_OFF from the
machine reset path.
As part of this ioctl, the secure guest is essentially transitioned
back to normal mode so that it can reboot like a regular guest and
become secure again.
This ioctl has no effect when invoked for a normal guest. If this ioctl
fails for a secure guest, the guest is terminated.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Message-Id: <20191219031445.8949-3-bharata@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Hi,
QDEV_PROP_PTR is marked in multiple places as "FIXME/TODO/remove
me". In most cases, it can be easily replaced with QDEV_PROP_LINK when
the pointer points to an Object.
There are a few places where such substitution isn't possible. For
those places, it seems reasonable to use a specific setter method
instead, and keep the user_creatable = false. In other places,
proper usage of qdev or other facilies is the solution.
The serial code wasn't converted to qdev, which makes it a bit more
archaic to deal with. Let's convert it first, so we can more easily
embed it from other devices, and re-export some properties and drop
QDEV_PROP_PTR usage.
-----BEGIN PGP SIGNATURE-----
iQJQBAABCAA6FiEEh6m9kz+HxgbSdvYt2ujhCXWWnOUFAl4UnUYcHG1hcmNhbmRy
ZS5sdXJlYXVAcmVkaGF0LmNvbQAKCRDa6OEJdZac5cfYEACcTfXklXdxLDj94Q5/
d6MxYqZWckO+vyMqOwonodl9BS3clpDDxbYzyfTpqwKS2cVg1eUUBPR7/eioX6zT
grM0rlgsKWJf9UurJwJWw7Zys7dXZMVJ2BdigLUEZrv9hFF15t344qoKgk4wYmBj
2wC7l7j2WZZ0vtXN7IH4/ZXnaN5/kdoPj6BrF0oNSJaq1AjPByQxmOJhvrxVsm6y
gn3la4XbfMIC68qPjcDJAScGXtCWG1Vydw9cFHwRpMfcvPyL70l6FMjIwrLYNQ9b
j1AkcEXeev5nWT+gLGxt+TGXB0Sd2ID9uRYxhyZRA4fdjHFtlWfdOwepOOlSlTO+
yfpf9STDLuDQGLTJyNZpYGGDDcm4xsJ8arD/7/Mq/35BQl9ZUT+m6uC1tDhxEHzf
+AD/Kh8rMptyAjwtqD2XbqyLoaFJCsPjZbjTj3SY08WaeqClmaAbSD2eaJiNXy4H
+rFg9P/eOB+71R1AoMKfiBFzdGV6TG5PLZOJ/oN02yqp0oW8eDWYcETB3j0tIgS1
u2WVCS2cd8IqYa+UQ7COOpoX0UwICmIWV64kxioD7uFQiK/1nQYw4UnPHv29qY6k
fTa8jUC5hPiDN1rRYqNpNoVJsstSZfSgpo5jV75sxSyDucupu+SM9qmo3+fBab+q
Eol3Ypz4virkNU8IYCYFFiG4Qg==
=iYVd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/prop-ptr-pull-request' into staging
Clean-ups: qom-ify serial and remove QDEV_PROP_PTR
Hi,
QDEV_PROP_PTR is marked in multiple places as "FIXME/TODO/remove
me". In most cases, it can be easily replaced with QDEV_PROP_LINK when
the pointer points to an Object.
There are a few places where such substitution isn't possible. For
those places, it seems reasonable to use a specific setter method
instead, and keep the user_creatable = false. In other places,
proper usage of qdev or other facilies is the solution.
The serial code wasn't converted to qdev, which makes it a bit more
archaic to deal with. Let's convert it first, so we can more easily
embed it from other devices, and re-export some properties and drop
QDEV_PROP_PTR usage.
# gpg: Signature made Tue 07 Jan 2020 15:01:26 GMT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/prop-ptr-pull-request: (37 commits)
qdev/qom: remove some TODO limitations now that PROP_PTR is gone
qdev: remove QDEV_PROP_PTR
qdev: remove PROP_MEMORY_REGION
omap-gpio: remove PROP_PTR
omap-i2c: remove PROP_PTR
omap-intc: remove PROP_PTR
smbus-eeprom: remove PROP_PTR
cris: improve passing PIC interrupt vector to the CPU
mips/cps: fix setting saar property
qdev: use g_strcmp0() instead of open-coding it
leon3: use qdev gpio facilities for the PIL
leon3: use qemu_irq framework instead of callback as property
dp8393x: replace PROP_PTR with PROP_LINK
etraxfs: remove PROP_PTR usage
lance: replace PROP_PTR with PROP_LINK
vmmouse: replace PROP_PTR with PROP_LINK
sm501: make SerialMM a child, export chardev property
mips: use sysbus_mmio_get_region() instead of internal fields
mips: use sysbus_add_io()
mips: baudbase is 115200 by default
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bugfixes all over the place.
HMAT support.
New flags for vhost-user-blk utility.
Auto-tuning of seg max for virtio storage.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl4TaMEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpvzgH/2LyDAzCa9h93ikSJjmyUk5FUaqve38daEb3
S3JYjwKxQx7u1ydooKhvBQnBCZ2i3S+k62gfYyKB+nBv8xvjs0Eg5D1YJ5E8hciy
lf5OFGWWtX2iPDjZwQwT13kiJe0o3JRGxJJ6XqTEG+1EYOp7cky/FEv4PD030b9m
I2wROZ/Am+onB9YJX8c0Vv1CG+AryuJNXnvwQzTXEjj4U7bEYUyJwVZaCRyAdWQ3
uYXIZN9VwjVX6BFvy9ZAJbEsUVJvOM1/aQaDqcrLz+VlzRT7bRkKHi2G3vakrm1I
r5OpgyLo84132awCncbSykKDH5o8WaxLaJBjGmuBfasMz9wPzAg=
=uL1o
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci, pc: fixes, features
Bugfixes all over the place.
HMAT support.
New flags for vhost-user-blk utility.
Auto-tuning of seg max for virtio storage.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 06 Jan 2020 17:05:05 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (32 commits)
intel_iommu: add present bit check for pasid table entries
intel_iommu: a fix to vtd_find_as_from_bus_num()
virtio-net: delete also control queue when TX/RX deleted
virtio: reset region cache when on queue deletion
virtio-mmio: update queue size on guest write
tests: add virtio-scsi and virtio-blk seg_max_adjust test
virtio: make seg_max virtqueue size dependent
hw: fix using 4.2 compat in 5.0 machine types for i440fx/q35
vhost-user-scsi: reset the device if supported
vhost-user: add VHOST_USER_RESET_DEVICE to reset devices
hw/pci/pci_host: Let pci_data_[read/write] use unsigned 'size' argument
hw/pci/pci_host: Remove redundant PCI_DPRINTF()
virtio-mmio: Clear v2 transport state on soft reset
ACPI: add expected files for HMAT tests (acpihmat)
tests/bios-tables-test: add test cases for ACPI HMAT
tests/numa: Add case for QMP build HMAT
hmat acpi: Build Memory Side Cache Information Structure(s)
hmat acpi: Build System Locality Latency and Bandwidth Information Structure(s)
hmat acpi: Build Memory Proximity Domain Attributes Structure(s)
numa: Extend CLI to provide memory side cache information
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Chardev events are listed in the QEMUChrEvent enum. To be
able to use this enum in the IOEventHandler typedef, we need to
explicit all the events ignored by this frontend, to silent the
following GCC warning:
CC hw/char/virtio-console.o
hw/char/virtio-console.c: In function ‘chr_event’:
hw/char/virtio-console.c:154:5: error: enumeration value ‘CHR_EVENT_BREAK’ not handled in switch [-Werror=switch]
154 | switch (event) {
| ^~~~~~
hw/char/virtio-console.c:154:5: error: enumeration value ‘CHR_EVENT_MUX_IN’ not handled in switch [-Werror=switch]
hw/char/virtio-console.c:154:5: error: enumeration value ‘CHR_EVENT_MUX_OUT’ not handled in switch [-Werror=switch]
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-11-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum. To be
able to use this enum in the IOEventHandler typedef, we need to
explicit all the events ignored by this frontend, to silent the
following GCC warning:
CC s390x-softmmu/hw/block/vhost-user-blk.o
hw/block/vhost-user-blk.c: In function ‘vhost_user_blk_event’:
hw/block/vhost-user-blk.c:370:5: error: enumeration value ‘CHR_EVENT_BREAK’ not handled in switch [-Werror=switch]
370 | switch (event) {
| ^~~~~~
hw/block/vhost-user-blk.c:370:5: error: enumeration value ‘CHR_EVENT_MUX_IN’ not handled in switch [-Werror=switch]
hw/block/vhost-user-blk.c:370:5: error: enumeration value ‘CHR_EVENT_MUX_OUT’ not handled in switch [-Werror=switch]
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-10-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum. To be
able to use this enum in the IOEventHandler typedef, we need to
explicit all the events ignored by this frontend, to silent the
following GCC warning:
hw/usb/ccid-card-passthru.c: In function ‘ccid_card_vscard_event’:
hw/usb/ccid-card-passthru.c:314:5: error: enumeration value ‘CHR_EVENT_MUX_IN’ not handled in switch [-Werror=switch]
314 | switch (event) {
| ^~~~~~
hw/usb/ccid-card-passthru.c:314:5: error: enumeration value ‘CHR_EVENT_MUX_OUT’ not handled in switch [-Werror=switch]
hw/usb/ccid-card-passthru.c:314:5: error: enumeration value ‘CHR_EVENT_CLOSED’ not handled in switch [-Werror=switch]
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum. To be
able to use this enum in the IOEventHandler typedef, we need to
explicit all the events ignored by this frontend, to silent the
following GCC warning:
CC hw/usb/redirect.o
hw/usb/redirect.c: In function ‘usbredir_chardev_event’:
hw/usb/redirect.c:1361:5: error: enumeration value ‘CHR_EVENT_BREAK’ not handled in switch [-Werror=switch]
1361 | switch (event) {
| ^~~~~~
hw/usb/redirect.c:1361:5: error: enumeration value ‘CHR_EVENT_MUX_IN’ not handled in switch [-Werror=switch]
hw/usb/redirect.c:1361:5: error: enumeration value ‘CHR_EVENT_MUX_OUT’ not handled in switch [-Werror=switch]
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum. To be
able to use this enum in the IOEventHandler typedef, we need to
explicit all the events ignored by this frontend, to silent the
following GCC warning:
hw/usb/dev-serial.c: In function ‘usb_serial_event’:
hw/usb/dev-serial.c:468:5: error: enumeration value ‘CHR_EVENT_MUX_IN’ not handled in switch [-Werror=switch]
468 | switch (event) {
| ^~~~~~
hw/usb/dev-serial.c:468:5: error: enumeration value ‘CHR_EVENT_MUX_OUT’ not handled in switch [-Werror=switch]
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum. To be
able to use this enum in the IOEventHandler typedef, we need to
explicit all the events ignored by this frontend, to silent the
following GCC warning:
CC s390x-softmmu/hw/char/terminal3270.o
hw/char/terminal3270.c: In function ‘chr_event’:
hw/char/terminal3270.c:156:5: error: enumeration value ‘CHR_EVENT_BREAK’ not handled in switch [-Werror=switch]
156 | switch (event) {
| ^~~~~~
hw/char/terminal3270.c:156:5: error: enumeration value ‘CHR_EVENT_MUX_IN’ not handled in switch [-Werror=switch]
hw/char/terminal3270.c:156:5: error: enumeration value ‘CHR_EVENT_MUX_OUT’ not handled in switch [-Werror=switch]
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Chardev events are listed in the QEMUChrEvent enum. To be
able to use this enum in the IOEventHandler typedef, we need to
explicit all the events ignored by this frontend, to silent the
following GCC warning:
hw/ipmi/ipmi_bmc_extern.c: In function ‘chr_event’:
hw/ipmi/ipmi_bmc_extern.c:389:5: error: enumeration value ‘CHR_EVENT_BREAK’ not handled in switch [-Werror=switch]
389 | switch (event) {
| ^~~~~~
hw/ipmi/ipmi_bmc_extern.c:389:5: error: enumeration value ‘CHR_EVENT_MUX_IN’ not handled in switch [-Werror=switch]
hw/ipmi/ipmi_bmc_extern.c:389:5: error: enumeration value ‘CHR_EVENT_MUX_OUT’ not handled in switch [-Werror=switch]
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20191218172009.8868-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since we don't use these methods before defining them,
no need to forward-declare them.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No longer used in the tree. The comment about user_creatable is still
quite relevant, but there is already a similar comment in qdev-core.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
Move/adapt the existing TODO comment about a clock framework.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
(in theory there should probably be different methods for omap1 &
omap2 intc, but this is left as a future improvement)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Instead, set the initial data field directly.
(the initial data is an array of 256 bytes. As I don't know if it may
change over time, I keep the pointer to original buffer as is, but it
might be worth to consider to copy it instead)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Instead of accessing cpu interrupt vector directly from PIC, send the
vector value over the qemu_irq.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
There is no "saar" property. Note: I haven't been able to test this
code. Help welcome.
May fix commit 043715d1e0 ("target/mips:
Update ITU to utilize SAARI and SAAR CP0 registers")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
As Peter Maydell once said:
"Creating a gpio pin on some object that isn't yourself
looks a bit odd, but all this leon3 code is modifying
the CPU object from the outside anyway. Someday we might
tidy it up, but not today."
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
"set_pin_in" property is used to define a callback mechanism where the
device says "call the callback function, passing it an opaque cookie
and a 32-bit value". We already have a generic mechanism for doing
that, which is the qemu_irq. So we should just use that.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Link property is the correct way to pass a MemoryRegion to a device
for DMA purposes.
Sidenote: as a sysbus device, this remains non-usercreatable
even though we can drop the specific flag here.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
etraxfs_dma_client are not Object, so can't be exposed to user with
QOM path. Let's remove property usage and move the constructor to the
.c unit, simplifying some code on the way.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The device remains non-user creatable since it is a sysbus device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
While at it, use the expected type.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Embed the SerialMM sybus device, and re-export its "chardev" property.
That way, we can get rid of PROP_PTR "chr-state" and better track
devices relationship.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Register the memory region with sysbus_init_mmio() and look it up with
sysbus_mmio_get_region() to avoid accessing internal device fields.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
sysbus devices should use the associated helper function instead of
calling memory_region_add_subregion() manually. This simplifies
slightly the code.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
(The default value is set for TYPE_SERIAL in serial_properties)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
The function is specific to mipssim, let's inline it.
(when inlining, we use a DeviceState variable instead of SerialIO, as
it is the most common type used, and avoids having too many casts)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Make serial IO a proper sysbus device, similar to serial MM.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Make SerialMM a regular sysbus device, by registering the irq, and the
mmio region. Reexport the internal serial properties.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Add a qdev property for endianness, so memory region setup can be done
in realize.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
And a property and rename "it_shift" field to "regshift", as it seems
to be more popular (and I don't know what "it" stands for).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Memory mapped serial device is in fact a sysbus device. The following
patches will make use of sysbus facilities for resource and
registration. In particular, "serial-mm: use sysbus facilities" will
move internal serial realization to serial_mm_realize callback to
follow qdev best practices.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Instead of calling serial_exit_core() directly, use the QDev unrealize
callback.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Instead of calling serial_realize_core(), use the QDev realize
callback.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This is more QOM-friendly, callers may set/get the property themself.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Migration from old to new code works, however the other way fails for
devices that use serial_init/serial_mm_init with "base", used as
instance_id previously.
(with qdev_set_legacy_instance_id, the alias_id is only used in
savevm.c:find_se(), and thus can only be used to match against
"legacy" instance id values. On new code, instance_id is generated
incrementally from 0 with calculate_new_instance_id(), based on
"qdev-path/vmsd-name")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: xiaoqiang zhao <zxq_yx_007@163.com>
Make SerialState a device (the following patches will introduce IO/MM
sysbus serial devices)
None of the serial_{,mm}_init() callers actually free the returned
value (even if they did, it would be quite harmless), so we can change
the object allocation at will.
However, the devices that embed SerialState must now have their field
QOM-initialized manually (isa, pci, pci-multi).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Common function to be reused in next patch.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
On Linux, calling `reboot(RB_AUTOBOOT);` will result in
arch/m68k/mac/misc.c's mac_reset function being called. That in turn
looks at the rombase (or uses 0x40800000 is there's no rombase), adds
0xa, and jumps to that address. At the moment, there's nothing there, so
the kernel just crashes when trying to reboot. So, this commit adds a
very simple implementation at that location, which just writes to via2
to power down. We also correct the value of ROMBASE while we're at it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200102120150.281082-1-Jason@zx2c4.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This allows to save and restore the content of the PRAM.
It may be useful if we want to check the configuration or to change it.
The backend is added using mtd interface, for instance:
... -drive file=pram.img,format=raw,if=mtd ...
where pram.img is the file where the data will be stored, its size must
be 256 bytes.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20191219201439.84804-3-laurent@vivier.eu>
The command byte is not decoded correctly.
This patch reworks the RTC/PRAM interface and fixes the problem.
It adds a comment before the function to explain how are encoded commands
and some trace-events to ease debugging.
Bug: https://bugs.launchpad.net/qemu/+bug/1856549
Fixes: 6dca62a000 ("hw/m68k: add VIA support")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20191219201439.84804-2-laurent@vivier.eu>
The SM501 is a Mobile Multimedia Companion Chip with 2 UARTs.
This model only implements the first UART. Being part of the
chipset, the UART block is always mapped in memory, regardless
of whether we provide a chardev backend.
Since commit 12051d82f, qemu_chr_fe_init() accepts a NULL chardev.
Let's remove the chardev check and always map the UART in the
chipset memory.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191122133623.13004-1-philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The MC146818 sits on an ISA bus. Since it can not be used
without it, select ISA in the Kconfig.
Fixes: 82f5181777 ("kconfig: introduce kconfig files", 2019-03-07)
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191224111628.3551-1-philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only the OpenBIOS and SLOF firmwares use the CHRP NVRAM layout.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-14-philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The NMC93xx EEPROM is only used by few NIC cards and the
Am53C974 SCSI controller.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-13-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Not all machines use the ppc_create_page_sizes_prop() helper.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-12-philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The fw_cfg helpers are only used by machines using OpenBIOS.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-11-philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CONFIG_PSERIES already selects CONFIG_PCI.
Simplify the Makefile rules.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-10-philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When configured with --without-default-devices, the build fails:
LINK ppc-softmmu/qemu-system-ppc
/usr/bin/ld: hw/ppc/virtex_ml507.o: in function `ppc440_init_xilinx':
hw/ppc/virtex_ml507.c:112: undefined reference to `ppcuic_init'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:206: qemu-system-ppc] Error 1
make: *** [Makefile:483: ppc-softmmu/all] Error 2
Fix by selecting the PPC4XX config.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-9-philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When configured with --without-default-devices, the build fails:
LINK ppc-softmmu/qemu-system-ppc
/usr/bin/ld: hw/ppc/sam460ex.o: in function `sam460ex_init':
hw/ppc/sam460ex.c:313: undefined reference to `ppc4xx_plb_init'
/usr/bin/ld: hw/ppc/sam460ex.c:353: undefined reference to `ppc405_ebc_init'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:206: qemu-system-ppc] Error 1
Fix by selecting the PPC405 config.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-8-philmd@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only the PowerPC e500-based platforms use the MPC I2C controller.
Do not build it for the other machines.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-7-philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When configured with --without-default-devices, the build fails:
LINK x86_64-softmmu/qemu-system-x86_64
/usr/bin/ld: hw/i386/microvm.o: in function `microvm_devices_init':
hw/i386/microvm.c:157: undefined reference to `serial_hds_isa_init'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:206: qemu-system-x86_64] Error 1
make: *** [Makefile:483: x86_64-softmmu/all] Error 2
While the MicroVM machine only uses the ISA serial port when the
MICROVM_MACHINE_ISA_SERIAL property is set, it has to be linked
with it. Replace the 'imply' Kconfig rule by a 'select'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 8259 Interrupt Controller sits on a ISA bus.
Add the missing dependency to fix:
LINK x86_64-softmmu/qemu-system-x86_64
/usr/bin/ld: ../hw/intc/i8259_common.o: in function `pic_common_realize':
hw/intc/i8259_common.c:84: undefined reference to `isa_register_ioport'
/usr/bin/ld: hw/intc/i8259_common.c:86: undefined reference to `isa_register_ioport'
/usr/bin/ld: ../hw/intc/i8259_common.o: in function `i8259_init_chip':
hw/intc/i8259_common.c:97: undefined reference to `isa_create'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:206: qemu-system-x86_64] Error 1
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 'usb-redir' device requires the USB core code to work. Do not
link it when there is no USB support. This fixes:
$ qemu-system-tricore -M tricore_testboard -device usb-redir
qemu-system-tricore: -device usb-redir: No 'usb-bus' bus found for device 'usb-redir'
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since i8254_common.c calls isa_register_ioport() from "hw/isa/isa.h"
we can not select it when ISA_BUS is disabled. Add a 'depends on'
clause.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200106171912.16523-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the 'vga=' parameter is succeeded by another parameter, QEMU 4.2.0
would refuse to start with a rather cryptic message:
$ qemu-system-x86_64 -kernel /boot/vmlinuz-linux -append 'vga=792 quiet'
qemu: can't parse 'vga' parameter: Invalid argument
It was not clear whether this applied to the '-vga std' parameter or the
'-append' one. Fix the parsing regression and clarify the error.
Fixes: 133ef074bd ("hw/i386/pc: replace use of strtol with qemu_strtoui in x86_load_linux()")
Cc: Sergio Lopez <slp@redhat.com>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Message-Id: <20191221162124.1159291-1-peter@lekensteyn.nl>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In commit 6c730e4af9 we introduced a stub to build the MicroVM
machine without Intel IOMMU. This stub is incomplete for the
other PC machines. Add the missing stubs.
Fixes: 6c730e4af9 ("pc: stubify x86 iommu", 2019-12-17)
Reported-by: Travis-CI
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191220154225.25879-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
5.0 machine type uses 4.2 compats. This seems to be incorrect, since
the latests machine type by now is 5.0 and it should use its own
compat or shouldn't use any relying on the defaults.
Seems, like this appeared because of some problems on merge/rebase.
Signed-off-by: Denis Plotnikov <dplotnikov@virtuozzo.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20191223072856.5369-1-dplotnikov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvm irqchip notifier is only registered if the device supports
INTx, however it's unconditionally removed. If the assigned device
does not support INTx, this will cause QEMU to crash when unplugging
the device from the system. Change it to conditionally remove the
notifier only if the notify hook is setup.
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v4.2
Reported-by: yanghliu@redhat.com
Debugged-by: Eduardo Habkost <ehabkost@redhat.com>
Fixes: c5478fea27 ("vfio/pci: Respond to KVM irqchip change notifier")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1782678
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Hi,
With external processes or helpers participating to the VM support, it
becomes necessary to handle their migration. Various options exist to
transfer their state:
1) as the VM memory, RAM or devices (we could say that's how
vhost-user devices can be handled today, they are expected to
restore from ring state)
2) other "vmstate" (as with TPM emulator state blobs)
3) left to be handled by management layer
1) is not practical, since an external processes may legitimatelly
need arbitrary state date to back a device or a service, or may not
even have an associated device.
2) needs ad-hoc code for each helper, but is simple and working
3) is complicated for management layer, QEMU has the migration timing
The proposed "dbus-vmstate" object will connect to a given D-Bus
address, and save/load from org.qemu.VMState1 owners on migration.
Thus helpers can easily have their state migrated with QEMU, without
implementing ad-hoc support (such as done for TPM emulation)
D-Bus is ubiquitous on Linux (it is systemd IPC), and can be made to
work on various other OSes. There are several implementations and good
bindings for various languages. (the tests/dbus-vmstate-test.c is a
good example of how simple the implementation of services can be, even
in C)
dbus-vmstate is put into use by the libvirt series "[PATCH 00/23] Use
a slirp helper process".
v2:
- fix build with broken mingw-glib
-----BEGIN PGP SIGNATURE-----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=M4kD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/dbus-vmstate7-pull-request' into staging
Add dbus-vmstate
Hi,
With external processes or helpers participating to the VM support, it
becomes necessary to handle their migration. Various options exist to
transfer their state:
1) as the VM memory, RAM or devices (we could say that's how
vhost-user devices can be handled today, they are expected to
restore from ring state)
2) other "vmstate" (as with TPM emulator state blobs)
3) left to be handled by management layer
1) is not practical, since an external processes may legitimatelly
need arbitrary state date to back a device or a service, or may not
even have an associated device.
2) needs ad-hoc code for each helper, but is simple and working
3) is complicated for management layer, QEMU has the migration timing
The proposed "dbus-vmstate" object will connect to a given D-Bus
address, and save/load from org.qemu.VMState1 owners on migration.
Thus helpers can easily have their state migrated with QEMU, without
implementing ad-hoc support (such as done for TPM emulation)
D-Bus is ubiquitous on Linux (it is systemd IPC), and can be made to
work on various other OSes. There are several implementations and good
bindings for various languages. (the tests/dbus-vmstate-test.c is a
good example of how simple the implementation of services can be, even
in C)
dbus-vmstate is put into use by the libvirt series "[PATCH 00/23] Use
a slirp helper process".
v2:
- fix build with broken mingw-glib
# gpg: Signature made Mon 06 Jan 2020 14:43:35 GMT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/dbus-vmstate7-pull-request:
tests: add dbus-vmstate-test
tests: add migration-helpers unit
dockerfiles: add dbus-daemon to some of latest distributions
configure: add GDBUS_CODEGEN
Add dbus-vmstate object
util: add dbus helper unit
docs: start a document to describe D-Bus usage
vmstate: replace DeviceState with VMStateIf
vmstate: add qom interface to get id
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The present bit check for pasid entry (pe) and pasid directory
entry (pdire) were missed in previous commits as fpd bit check
doesn't require present bit as "Set". This patch adds the present
bit check for callers which wants to get a valid pe/pdire.
Cc: qemu-stable@nongnu.org
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Yi Sun <yi.y.sun@linux.intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Message-Id: <1578058086-4288-3-git-send-email-yi.l.liu@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Ensure the return value of vtd_find_as_from_bus_num() is NULL by
enforcing vtd_bus=NULL. This would help caller of vtd_find_as_from_bus_num()
to decide if any further operation on the returned vtd_bus.
Cc: qemu-stable@nongnu.org
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <1578058086-4288-2-git-send-email-yi.l.liu@intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1708480
If the control queue is not deleted together with TX/RX, it
later will be ignored in freeing cache resources and hot
unplug will not be completed.
Cc: qemu-stable@nongnu.org
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-Id: <20191226043649.14481-3-yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1708480
Fix leak of region reference that prevents complete
device deletion on hot unplug.
Cc: qemu-stable@nongnu.org
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-Id: <20191226043649.14481-2-yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some guests read back queue size after writing it.
Always update the on size write otherwise they might be confused.
Cc: qemu-stable@nongnu.org
Signed-off-by: Denis Plotnikov <dplotnikov@virtuozzo.com>
Message-Id: <20191224081446.17003-1-dplotnikov@virtuozzo.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Before the patch, seg_max parameter was immutable and hardcoded
to 126 (128 - 2) without respect to queue size. This has two negative effects:
1. when queue size is < 128, we have Virtio 1.1 specfication violation:
(2.6.5.3.1 Driver Requirements) seq_max must be <= queue_size.
This violation affects the old Linux guests (ver < 4.14). These guests
crash on these queue_size setups.
2. when queue_size > 128, as was pointed out by Denis Lunev <den@virtuozzo.com>,
seg_max restrics guest's block request length which affects guests'
performance making them issues more block request than needed.
https://lists.gnu.org/archive/html/qemu-devel/2017-12/msg03721.html
To mitigate this two effects, the patch adds the property adjusting seg_max
to queue size automaticaly. Since seg_max is a guest visible parameter,
the property is machine type managable and allows to choose between
old (seg_max = 126 always) and new (seg_max = queue_size - 2) behaviors.
Not to change the behavior of the older VMs, prevent setting the default
seg_max_adjust value for older machine types.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Denis Plotnikov <dplotnikov@virtuozzo.com>
Message-Id: <20191220140905.1718-2-dplotnikov@virtuozzo.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Hi,
The following patches have been extracted from the "[PATCH v6 00/25]
monitor: add asynchronous command type", as they are
reviewable/mergeable independantly.
They introduce some internal API changes, and fix
qemu_open()/qemu_close()/unlink() misusages which should be quite
harmless.
-----BEGIN PGP SIGNATURE-----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=aSgS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/screendump-pull-request' into staging
console: screendump improvements
Hi,
The following patches have been extracted from the "[PATCH v6 00/25]
monitor: add asynchronous command type", as they are
reviewable/mergeable independantly.
They introduce some internal API changes, and fix
qemu_open()/qemu_close()/unlink() misusages which should be quite
harmless.
# gpg: Signature made Fri 03 Jan 2020 09:07:51 GMT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/screendump-pull-request:
screendump: use qemu_unlink()
osdep: add qemu_unlink()
screendump: replace FILE with QIOChannel and fix close()/qemu_close()
object: add g_autoptr support
ui: add pixman image g_autoptr support
ppm-save: pass opened fd
console: add graphic_hw_update_done()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace DeviceState dependency with VMStateIf on vmstate API.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Add an interface to get the instance id, instead of depending on
Device and qdev_get_dev_path().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Apply previous commit to hda_audio_input_cb for the same
reasons.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-id: 20200104091122.13971-2-vr_qemu@t-online.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since commit 1930616b98 "audio: make mixeng optional" the
function hda_audio_output_cb can no longer assume the function
parameter avail contains the free buffer size. With the playback
mixing-engine turned off this leads to a broken playback rate
control and playback buffer drops in regular intervals.
This patch moves down the rate calculation, so the correct
buffer fill level is used for the calculation.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-id: 20200104091122.13971-1-vr_qemu@t-online.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
5.0 machine type uses 4.2 compats. This seems to be incorrect, since
the latests machine type by now is 5.0 and it should use its own
compat or shouldn't use any relying on the defaults.
Seems, like this appeared because of some problems on merge/rebase.
Signed-off-by: Denis Plotnikov <dplotnikov@virtuozzo.com>
Message-Id: <20191223072856.5369-1-dplotnikov@virtuozzo.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the vhost-user-scsi backend supports the VHOST_USER_F_RESET_DEVICE
protocol feature, then the device can be reset when requested.
If this feature is not supported, do not try a reset as this will send
a VHOST_USER_RESET_OWNER that the backend is not expecting,
potentially putting into an inoperable state.
Signed-off-by: David Vrabel <david.vrabel@nutanix.com>
Signed-off-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <1572385083-5254-3-git-send-email-raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a VHOST_USER_RESET_DEVICE message which will reset the vhost user
backend. Disabling all rings, and resetting all internal state, ready
for the backend to be reinitialized.
A backend has to report it supports this features with the
VHOST_USER_PROTOCOL_F_RESET_DEVICE protocol feature bit. If it does
so, the new message is used instead of sending a RESET_OWNER which has
had inconsistent implementations.
Signed-off-by: David Vrabel <david.vrabel@nutanix.com>
Signed-off-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <1572385083-5254-2-git-send-email-raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Both functions are called by MemoryRegionOps.[read/write] handlers
with unsigned 'size' argument. Both functions call
pci_host_config_[read/write]_common() which expect a uint32_t 'len'
parameter (also unsigned).
Since it is pointless (and confuse) to use a signed value, use a
unsigned type.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191216002134.18279-3-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In commit 3bf4dfdd11 we introduced the pci_cfg_[read/write]
trace events in pci_host_config_[read/write]_common().
We have the following call trace:
pci_host_data_[read/write]()
- PCI_DPRINTF()
- pci_data_[read/write]()
- PCI_DPRINTF()
- pci_host_config_[read/write]_common()
trace_pci_cfg_[read/write]()
Since the PCI_DPRINTF() calls are redundant with the trace
events, remove them.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191216002134.18279-2-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At the moment when the guest writes a status of 0, we only reset the
virtio core state but not the virtio-mmio state. The virtio-mmio
specification says (v1.1 cs01, 4.2.2.1 Device Requirements:
MMIO Device Register Layout):
Upon reset, the device MUST clear all bits in InterruptStatus and
ready bits in the QueueReady register for all queues in the device.
The core already takes care of InterruptStatus by clearing isr, but we
still need to clear QueueReady.
It would be tempting to clean all registers, but since the specification
doesn't say anything more, guests could rely on the registers keeping
their state across reset. Linux for example, relies on this for
GuestPageSize in the legacy MMIO tranport.
Fixes: 44e687a4d9 ("virtio-mmio: implement modern (v2) personality (virtio-1)")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20191213095410.1516119-1-jean-philippe@linaro.org>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This structure describes memory side cache information for memory
proximity domains if the memory side cache is present and the
physical device forms the memory side cache.
The software could use this information to effectively place
the data in memory to maximize the performance of the system
memory that use the memory side cache.
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Daniel Black <daniel@linux.ibm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-7-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This structure describes the memory access latency and bandwidth
information from various memory access initiator proximity domains.
The latency and bandwidth numbers represented in this structure
correspond to rated latency and bandwidth for the platform.
The software could use this information as hint for optimization.
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-6-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
HMAT is defined in ACPI 6.3: 5.2.27 Heterogeneous Memory Attribute Table
(HMAT). The specification references below link:
http://www.uefi.org/sites/default/files/resources/ACPI_6_3_final_Jan30.pdf
It describes the memory attributes, such as memory side cache
attributes and bandwidth and latency details, related to the
Memory Proximity Domain. The software is
expected to use this information as hint for optimization.
This structure describes Memory Proximity Domain Attributes by memory
subsystem and its associativity with processor proximity domain as well as
hint for memory usage.
In the linux kernel, the codes in drivers/acpi/hmat/hmat.c parse and report
the platform's HMAT tables.
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Daniel Black <daniel@linux.ibm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-5-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add -numa hmat-cache option to provide Memory Side Cache Information.
These memory attributes help to build Memory Side Cache Information
Structure(s) in ACPI Heterogeneous Memory Attribute Table (HMAT).
Before using hmat-cache option, enable HMAT with -machine hmat=on.
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-4-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Add -numa hmat-lb option to provide System Locality Latency and
Bandwidth Information. These memory attributes help to build
System Locality Latency and Bandwidth Information Structure(s)
in ACPI Heterogeneous Memory Attribute Table (HMAT). Before using
hmat-lb option, enable HMAT with -machine hmat=on.
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-3-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
In ACPI 6.3 chapter 5.2.27 Heterogeneous Memory Attribute Table (HMAT),
The initiator represents processor which access to memory. And in 5.2.27.3
Memory Proximity Domain Attributes Structure, the attached initiator is
defined as where the memory controller responsible for a memory proximity
domain. With attached initiator information, the topology of heterogeneous
memory can be described. Add new machine property 'hmat' to enable all
HMAT specific options.
Extend CLI of "-numa node" option to indicate the initiator numa node-id.
In the linux kernel, the codes in drivers/acpi/hmat/hmat.c parse and report
the platform's HMAT tables. Before using initiator option, enable HMAT with
-machine hmat=on.
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Jingqi Liu <jingqi.liu@intel.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20191213011929.2520-2-tao3.xu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtqueue notifications are not necessary during polling, so we disable
them. This allows the guest driver to avoid MMIO vmexits.
Unfortunately the virtio-blk and virtio-scsi handler functions re-enable
notifications, defeating this optimization.
Fix virtio-blk and virtio-scsi emulation so they leave notifications
disabled. The key thing to remember for correctness is that polling
always checks one last time after ending its loop, therefore it's safe
to lose the race when re-enabling notifications at the end of polling.
There is a measurable performance improvement of 5-10% with the null-co
block driver. Real-life storage configurations will see a smaller
improvement because the MMIO vmexit overhead contributes less to
latency.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191209210957.65087-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the SLOF firmware for pseries guests will disable/re-enable
a PCI device multiple times via IO/MEM/MASTER bits of PCI_COMMAND
register after the initial probe/feature negotiation, as it tends to
work with a single device at a time at various stages like probing
and running block/network bootloaders without doing a full reset
in-between.
In QEMU, when PCI_COMMAND_MASTER is disabled we disable the
corresponding IOMMU memory region, so DMA accesses (including to vring
fields like idx/flags) will no longer undergo the necessary
translation. Normally we wouldn't expect this to happen since it would
be misbehavior on the driver side to continue driving DMA requests.
However, in the case of pseries, with iommu_platform=on, we trigger the
following sequence when tearing down the virtio-blk dataplane ioeventfd
in response to the guest unsetting PCI_COMMAND_MASTER:
#2 0x0000555555922651 in virtqueue_map_desc (vdev=vdev@entry=0x555556dbcfb0, p_num_sg=p_num_sg@entry=0x7fffe657e1a8, addr=addr@entry=0x7fffe657e240, iov=iov@entry=0x7fffe6580240, max_num_sg=max_num_sg@entry=1024, is_write=is_write@entry=false, pa=0, sz=0)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:757
#3 0x0000555555922a89 in virtqueue_pop (vq=vq@entry=0x555556dc8660, sz=sz@entry=184)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:950
#4 0x00005555558d3eca in virtio_blk_get_request (vq=0x555556dc8660, s=0x555556dbcfb0)
at /home/mdroth/w/qemu.git/hw/block/virtio-blk.c:255
#5 0x00005555558d3eca in virtio_blk_handle_vq (s=0x555556dbcfb0, vq=0x555556dc8660)
at /home/mdroth/w/qemu.git/hw/block/virtio-blk.c:776
#6 0x000055555591dd66 in virtio_queue_notify_aio_vq (vq=vq@entry=0x555556dc8660)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:1550
#7 0x000055555591ecef in virtio_queue_notify_aio_vq (vq=0x555556dc8660)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:1546
#8 0x000055555591ecef in virtio_queue_host_notifier_aio_poll (opaque=0x555556dc86c8)
at /home/mdroth/w/qemu.git/hw/virtio/virtio.c:2527
#9 0x0000555555d02164 in run_poll_handlers_once (ctx=ctx@entry=0x55555688bfc0, timeout=timeout@entry=0x7fffe65844a8)
at /home/mdroth/w/qemu.git/util/aio-posix.c:520
#10 0x0000555555d02d1b in try_poll_mode (timeout=0x7fffe65844a8, ctx=0x55555688bfc0)
at /home/mdroth/w/qemu.git/util/aio-posix.c:607
#11 0x0000555555d02d1b in aio_poll (ctx=ctx@entry=0x55555688bfc0, blocking=blocking@entry=true)
at /home/mdroth/w/qemu.git/util/aio-posix.c:639
#12 0x0000555555d0004d in aio_wait_bh_oneshot (ctx=0x55555688bfc0, cb=cb@entry=0x5555558d5130 <virtio_blk_data_plane_stop_bh>, opaque=opaque@entry=0x555556de86f0)
at /home/mdroth/w/qemu.git/util/aio-wait.c:71
#13 0x00005555558d59bf in virtio_blk_data_plane_stop (vdev=<optimized out>)
at /home/mdroth/w/qemu.git/hw/block/dataplane/virtio-blk.c:288
#14 0x0000555555b906a1 in virtio_bus_stop_ioeventfd (bus=bus@entry=0x555556dbcf38)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-bus.c:245
#15 0x0000555555b90dbb in virtio_bus_stop_ioeventfd (bus=bus@entry=0x555556dbcf38)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-bus.c:237
#16 0x0000555555b92a8e in virtio_pci_stop_ioeventfd (proxy=0x555556db4e40)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-pci.c:292
#17 0x0000555555b92a8e in virtio_write_config (pci_dev=0x555556db4e40, address=<optimized out>, val=1048832, len=<optimized out>)
at /home/mdroth/w/qemu.git/hw/virtio/virtio-pci.c:613
I.e. the calling code is only scheduling a one-shot BH for
virtio_blk_data_plane_stop_bh, but somehow we end up trying to process
an additional virtqueue entry before we get there. This is likely due
to the following check in virtio_queue_host_notifier_aio_poll:
static bool virtio_queue_host_notifier_aio_poll(void *opaque)
{
EventNotifier *n = opaque;
VirtQueue *vq = container_of(n, VirtQueue, host_notifier);
bool progress;
if (!vq->vring.desc || virtio_queue_empty(vq)) {
return false;
}
progress = virtio_queue_notify_aio_vq(vq);
namely the call to virtio_queue_empty(). In this case, since no new
requests have actually been issued, shadow_avail_idx == last_avail_idx,
so we actually try to access the vring via vring_avail_idx() to get
the latest non-shadowed idx:
int virtio_queue_empty(VirtQueue *vq)
{
bool empty;
...
if (vq->shadow_avail_idx != vq->last_avail_idx) {
return 0;
}
rcu_read_lock();
empty = vring_avail_idx(vq) == vq->last_avail_idx;
rcu_read_unlock();
return empty;
but since the IOMMU region has been disabled we get a bogus value (0
usually), which causes virtio_queue_empty() to falsely report that
there are entries to be processed, which causes errors such as:
"virtio: zero sized buffers are not allowed"
or
"virtio-blk missing headers"
and puts the device in an error state.
This patch works around the issue by introducing virtio_set_disabled(),
which sets a 'disabled' flag to bypass checks like virtio_queue_empty()
when bus-mastering is disabled. Since we'd check this flag at all the
same sites as vdev->broken, we replace those checks with an inline
function which checks for either vdev->broken or vdev->disabled.
The 'disabled' flag is only migrated when set, which should be fairly
rare, but to maintain migration compatibility we disable it's use for
older machine types. Users requiring the use of the flag in conjunction
with older machine types can set it explicitly as a virtio-device
option.
NOTES:
- This leaves some other oddities in play, like the fact that
DRIVER_OK also gets unset in response to bus-mastering being
disabled, but not restored (however the device seems to continue
working)
- Similarly, we disable the host notifier via
virtio_bus_stop_ioeventfd(), which seems to move the handling out
of virtio-blk dataplane and back into the main IO thread, and it
ends up staying there till a reset (but otherwise continues working
normally)
Cc: David Gibson <david@gibson.dropbear.id.au>,
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Message-Id: <20191120005003.27035-1-mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some guests read back queue size after writing it.
Update the size immediatly upon write otherwise
they get confused.
In particular this is the case for seabios.
Reported-by: Roman Kagan <rkagan@virtuozzo.com>
Suggested-by: Denis Plotnikov <dplotnikov@virtuozzo.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Should directly read DMAR_RTADDR_REG but not using 's->root'.
Because 's->root' is modified in 'vtd_root_table_setup()' so
that the first 12 bits are omitted. This causes the guest
iommu debugfs cannot show pasid tables.
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Message-Id: <20191205095439.29114-1-yi.y.sun@linux.intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
ivqs/ovqs/c_ivq/c_ovq is forgot to cleanup in
virtio_serial_device_unrealize, the memory leak stack is as bellow:
Direct leak of 1290240 byte(s) in 180 object(s) allocated from:
#0 0x7fc9bfc27560 in calloc (/usr/lib64/libasan.so.3+0xc7560)
#1 0x7fc9bed6f015 in g_malloc0 (/usr/lib64/libglib-2.0.so.0+0x50015)
#2 0x5650e02b83e7 in virtio_add_queue hw/virtio/virtio.c:2327
#3 0x5650e02847b5 in virtio_serial_device_realize hw/char/virtio-serial-bus.c:1089
#4 0x5650e02b56a7 in virtio_device_realize hw/virtio/virtio.c:3504
#5 0x5650e03bf031 in device_set_realized hw/core/qdev.c:876
#6 0x5650e0531efd in property_set_bool qom/object.c:2080
#7 0x5650e053650e in object_property_set_qobject qom/qom-qobject.c:26
#8 0x5650e0533e14 in object_property_set_bool qom/object.c:1338
#9 0x5650e04c0e37 in virtio_pci_realize hw/virtio/virtio-pci.c:1801
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Amit Shah <amit@kernel.org>
Cc: "Marc-André Lureau" <marcandre.lureau@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1575444716-17632-3-git-send-email-pannengyuan@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
ivq/dvq/svq/free_page_vq is forgot to cleanup in
virtio_balloon_device_unrealize, the memory leak stack is as follow:
Direct leak of 14336 byte(s) in 2 object(s) allocated from:
#0 0x7f99fd9d8560 in calloc (/usr/lib64/libasan.so.3+0xc7560)
#1 0x7f99fcb20015 in g_malloc0 (/usr/lib64/libglib-2.0.so.0+0x50015)
#2 0x557d90638437 in virtio_add_queue hw/virtio/virtio.c:2327
#3 0x557d9064401d in virtio_balloon_device_realize hw/virtio/virtio-balloon.c:793
#4 0x557d906356f7 in virtio_device_realize hw/virtio/virtio.c:3504
#5 0x557d9073f081 in device_set_realized hw/core/qdev.c:876
#6 0x557d908b1f4d in property_set_bool qom/object.c:2080
#7 0x557d908b655e in object_property_set_qobject qom/qom-qobject.c:26
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-Id: <1575444716-17632-2-git-send-email-pannengyuan@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Let's make sure calling this twice is harmless -
no known instances, but seems safer.
Suggested-by: Pan Nengyuan <pannengyuan@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Devices tend to maintain vq pointers, allow deleting them trough a vq pointer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Add a function to be called when a graphic update is done.
Declare the QXL renderer as async: render_update_cookie_num counts the
number of outstanding updates, and graphic_hw_update_done() is called
when it reaches none.
(note: this is preliminary work for asynchronous screendump support)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The smmuv3_record_event() function that generates the F_STE_FETCH error
uses the EVT_SET_ADDR macro to record the fetch address, placing it in
32-bit words 4 and 5.
The correct position for this address is in words 6 and 7, per the
SMMUv3 Architecture Specification.
Update the function to use the EVT_SET_ADDR2 macro instead, which is the
macro intended for writing to these words.
ref. ARM IHI 0070C, section 7.3.4.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-7-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bit offsets in the EVT_SET_ADDR2 macro do not match those specified
in the ARM SMMUv3 Architecture Specification. In all events that use
this macro, e.g. F_WALK_EABT, the faulting fetch address or IPA actually
occupies the 32-bit words 6 and 7 in the event record contiguously, with
the upper and lower unused bits clear due to alignment or maximum
supported address bits. How many bits are clear depends on the
individual event type.
Update the macro to write to the correct words in the event record so
that guest drivers can obtain accurate address information on events.
ref. ARM IHI 0070C, sections 7.3.12 through 7.3.16.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-6-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the specification, and as observed in hardware, the SMMUv3 aligns
the SMMU_STRTAB_BASE address to the size of the table by masking out the
respective least significant bits in the ADDR field.
Apply this masking logic to our smmu_find_ste() lookup function per the
specification.
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-5-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When checking whether a stream ID is in range of the stream table, we
have so far been only checking it against our implementation limit
(SMMU_IDR1_SIDSIZE). However, the guest can program the
STRTAB_BASE_CFG.LOG2SIZE field to a size that is smaller than this
limit.
Check the stream ID against this limit as well to match the hardware
behavior of raising C_BAD_STREAMID events in case the limit is exceeded.
Also, ensure that we do not go one entry beyond the end of the table by
checking that its index is strictly smaller than the table size.
ref. ARM IHI 0070C, section 6.3.24.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-4-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are two issues with the current value of SMMU_BASE_ADDR_MASK:
- At the lower end, we are clearing bits [4:0]. Per the SMMUv3 spec,
we should also be treating bit 5 as zero in the base address.
- At the upper end, we are clearing bits [63:48]. Per the SMMUv3 spec,
only bits [63:52] must be explicitly treated as zero.
Update the SMMU_BASE_ADDR_MASK value to mask out bits [63:52] and [5:0].
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-3-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the SMMU_STRTAB_BASE register, the stream table base address only
occupies bits [51:6]. Other bits, such as RA (bit [62]), must be masked
out to obtain the base address.
The branch for 2-level stream tables correctly applies this mask by way
of SMMU_BASE_ADDR_MASK, but the one for linear stream tables does not.
Apply the missing mask in that case as well so that the correct stream
base address is used by guests which configure a linear stream table.
Linux guests are unaffected by this change because they choose a 2-level
stream table layout for the QEMU SMMUv3, based on the size of its stream
ID space.
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-2-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This matches the configuration set by u-boot on the AST2600.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 080ca1267a09381c43cf3c50d434fb6c186f2b6e.1576215453.git-series.andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- test tci with Travis
- enable multiarch testing in Travis
- default to out-of-tree builds
- make changing logfile safe via RCU
- remove redundant tests
- remove gtester test from docker
- convert DEBUG_MMAP to tracepoints
- remove hand rolled glob function
- trigger tcg re-configure when needed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl37M6gACgkQ+9DbCVqe
KkQ0Rwf/d0lGDPQN1Uf0zqZRQQmDCqWVuqHhZJ5xWDjbyVT2eUwR07TvNZeUKEWX
iO+u6S7Tv91oLjZN5WjhaiuSjtJaEzCdcpkIJAWXLP/lzse37HEwvLBsdg71y+46
LNvBrJRPpQotdb7fjr8RgCwc1qg2Bz15ekSn7XIA175zTMmUsshLJBVhLbGNqrVm
F2UmjB9oFJ0+nzrcEnpFmWw7xvVrX1dImZXv5C2pvuHF7efSjGwiFviTRZgDjOGs
V7HiWRV1QcgTigncncxTMbhMTKTVKK+e7O+y0DZWt/NSrT/yLDy5rcwySpmvu6C+
cRmh/0tMo1KAhiz8Xy8LookhVj6hdA==
=OAkV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tesing-and-misc-191219-1' into staging
Various testing and logging updates
- test tci with Travis
- enable multiarch testing in Travis
- default to out-of-tree builds
- make changing logfile safe via RCU
- remove redundant tests
- remove gtester test from docker
- convert DEBUG_MMAP to tracepoints
- remove hand rolled glob function
- trigger tcg re-configure when needed
# gpg: Signature made Thu 19 Dec 2019 08:24:08 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tesing-and-misc-191219-1: (25 commits)
tests/tcg: ensure we re-configure if configure.sh is updated
trace: replace hand-crafted pattern_glob with g_pattern_match_simple
linux-user: convert target_munmap debug to a tracepoint
linux-user: log page table changes under -d page
linux-user: add target_mmap_complete tracepoint
linux-user: convert target_mmap debug to tracepoint
linux-user: convert target_mprotect debug to tracepoint
travis.yml: Remove the redundant clang-with-MAIN_SOFTMMU_TARGETS entry
docker: gtester is no longer used
Added tests for close and change of logfile.
Add use of RCU for qemu_logfile.
qemu_log_lock/unlock now preserves the qemu_logfile handle.
Add a mutex to guarantee single writer to qemu_logfile handle.
Cleaned up flow of code in qemu_set_log(), to simplify and clarify.
Fix double free issue in qemu_set_log_filename().
ci: build out-of-tree
travis.yml: Enable builds on arm64, ppc64le and s390x
tests/test-util-filemonitor: Skip test on non-x86 Travis containers
tests/hd-geo-test: Skip test when images can not be created
iotests: Skip test 079 if it is not possible to create large files
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit aa57020774, by mistake used MachineClass::numa_mem_supported
to check if NUMA is supported by machine and also as unrelated change
set it to true for sbsa-ref board.
Luckily change didn't break machines that support NUMA, as the field
is set to true for them.
But the field is not intended for checking if NUMA is supported and
will be flipped to false within this release for new machine types.
Fix it:
- by using previously used condition
!mc->cpu_index_to_instance_props || !mc->get_default_cpu_node_id
the first time and then use MachineState::numa_state down the road
to check if NUMA is supported
- dropping stray sbsa-ref chunk
Fixes: aa57020774
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1576154936-178362-3-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently parse_numa_node() is always called from already numa
enabled context.
Drop unnecessary check if numa is supported.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1576154936-178362-2-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When the number of a virtio-blk device's virtqueues is larger than
BITS_PER_LONG, the out-of-bounds access to bitmap[ ] will occur.
Fixes: e21737ab15 ("virtio-blk: multiqueue batch notify")
Cc: qemu-stable@nongnu.org
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Li Hangjing <lihangjing@baidu.com>
Reviewed-by: Xie Yongji <xieyongji@baidu.com>
Reviewed-by: Chai Wen <chaiwen@baidu.com>
Message-id: 20191216023050.48620-1-lihangjing@baidu.com
Message-Id: <20191216023050.48620-1-lihangjing@baidu.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
qemu_log_lock() now returns a handle and qemu_log_unlock() receives a
handle to unlock. This allows for changing the handle during logging
and ensures the lock() and unlock() are for the same file.
Also in target/tilegx/translate.c removed the qemu_log_lock()/unlock()
calls (and the log("\n")), since the translator can longjmp out of the
loop if it attempts to translate an instruction in an inaccessible page.
Signed-off-by: Robert Foley <robert.foley@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20191118211528.3221-5-robert.foley@linaro.org>
No reason for local_err here, use errp directly instead.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191205174635.18758-21-vsementsov@virtuozzo.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205174635.18758-18-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20191205174635.18758-17-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191205174635.18758-16-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205174635.18758-12-vsementsov@virtuozzo.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Rename Error ** parameter in check_only_migratable to common errp.
In device_set_realized:
- Move "if (local_err != NULL)" closer to error setters.
- Drop 'Error **local_errp': it doesn't save any LoCs, but it's very
unusual.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191205174635.18758-10-vsementsov@virtuozzo.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Mostly, Error ** is for returning error from the function, so the
callee sets it. However error_append_security_model_hint and
error_append_socket_sockfd_hint get already filled errp
parameter. They don't change the pointer itself, only change the
internal state of referenced Error object. So we can make it Error
*const * errp, to stress the behavior. It will also help coccinelle
script (in future) to distinguish such cases from common errp usage.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191205174635.18758-9-vsementsov@virtuozzo.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message replaced]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Mostly, Error ** is for returning error from the function, so the
callee sets it. However kvmppc_hint_smt_possible gets already filled
errp parameter. It doesn't change the pointer itself, only change the
internal state of referenced Error object. So we can make it Error
*const * errp, to stress the behavior. It will also help coccinelle
script (in future) to distinguish such cases from common errp usage.
While there, rename the function to
kvmppc_error_append_smt_possible_hint().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191205174635.18758-8-vsementsov@virtuozzo.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message replaced]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This reverts commit cdcca22aab.
Commit cdcca22aab is a superseded version of the next commit that
crept in by accident. Revert it, so the final version applies.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We don't need Error **, as all callers pass local Error object, which
isn't used after the call. Use Error * instead.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191205174635.18758-5-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Local Error * variables are conventionally named @err or @local_err,
and Error ** parameters @errp. Naming local variables like parameters
is confusing. Clean that up.
Naming parameters like local variables is also confusing. Left for
another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191204093625.14836-17-armbru@redhat.com>
memory_device_get_free_addr() dereferences @errp when
memory_device_check_addable() fails. That's wrong; see the big
comment in error.h. Introduced in commit 1b6d6af21b "pc-dimm: factor
out capacity and slot checks into MemoryDevice".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-11-armbru@redhat.com>
isa_ipmi_bt_realize(), ipmi_isa_realize(), pci_ipmi_bt_realize(), and
pci_ipmi_kcs_realize() dereference @errp when IPMIInterfaceClass
method init() fails. That's wrong; see the big comment in error.h.
Introduced in commit 0719029c47 "ipmi: Add an ISA KCS low-level
interface", then imitated in commit a9b74079cb "ipmi: Add a BT
low-level interface" and commit 12f983c6aa "ipmi: Add PCI IPMI
interfaces".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191204093625.14836-9-armbru@redhat.com>
fit_load_fdt() passes @errp to fit_image_addr(), then recovers from
ENOENT failures. Passing @errp is wrong, because it works only as
long as @errp is neither @error_fatal nor @error_abort. Error
recovery dereferences @errp. That's also wrong; see the big comment
in error.h. Error recovery can leave *errp pointing to a freed
Error object. Wrong, it must be null on success. Messed up in
commit 3eb99edb48 "loader-fit: Wean off error_printf()".
No caller actually passes such values, or uses *errp on success.
Fix anyway: splice in a local Error *err, and error_propagate().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191204093625.14836-8-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
legacy_acpi_cpu_plug_cb() dereferences @errp when
acpi_set_cpu_present_bit() fails. That's wrong; see the big comment
in error.h. Introduced in commit cc43364de7 "acpi/cpu-hotplug:
introduce helper function to keep bit setting in one place".
No caller actually passes null, and acpi_set_cpu_present_bit() can't
actually fail.
Fix anyway: drop acpi_set_cpu_present_bit()'s @errp parameter.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20191204093625.14836-7-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
vga_init_vbe is now used only from ISA VGA cards. Since the alias is
not needed anymore, remove it (effectively reverting commit 8294a64d7f,
"vga: fix vram double-mapping with -vga std and -M pc-0.12", 2012-05-29)
and the now unused vbe_mapped field of VGACommonState. The function now
consists of a single memory_region_add_subregion call, so we can inline
it; this avoids incorrect usage from PCI cards.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Based-on: <05af415a-5058-98b4-4a12-9d093a30b1e3@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the old pc-0.x machine types have been removed, we do not need
the old "rombar" hacks anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209125248.5849-5-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the old pc-0.x machine types have been removed, this config
knob is not required anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209125248.5849-4-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the old pc-0.x machine types are gone, we do not need
the "use_broken_id" hack anymore.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209125248.5849-3-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These machines can't be used reliably for migration anymore, quoting
https://lists.gnu.org/archive/html/qemu-devel/2018-12/msg04516.html :
"
due to the introduction of the memory API, the firmware is not
migrated correctly from source to destination. On QEMU <1.3 the
0xf0000-0xfffff area is basically a copy of the higher
0xffff0000-0xffffffff area, while on more recent versions it is
initialized with zeroes and the firmware copies from 0xffff0000 to
0xf0000. When you migrate from old to new QEMU, after reboot there's
nothing at 0xf0000 and bugs ensue.
"
The pc-0.x machines have been marked as deprecated since QEMU v4.0, so
it is time to remove them now.
And while we're at it, mark the remaining pc-1.x machine types
as deprecated now, too, so that we finally only have "pc-i440fx"
and "pc-q35" machine types left (apart from the non-versioned
"isapc" and "microvm") once we remove them in a couple of releases.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209125248.5849-2-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the XEN_IGD_PASSTHROUGH Kconfig option.
Xen build has that option selected by default. Non-Xen builds now
have to select this feature manually.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191209095002.32194-7-philmd@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can use a i440FX without the IGD passthrough host bridge.
Extract it into a new file, 'hw/pci-host/xen_igd_pt.c'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191209095002.32194-6-philmd@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use definitions from "hw/pci/pci_regs.h".
This also helps when using git-grep.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209095002.32194-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't enforce the -Wsign-conversion CPPFLAG, but it doesn't hurt
to avoid this warning:
warning: implicit conversion changes signedness: 'int' to 'size_t' (aka 'unsigned long') [-Wsign-conversion]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209095002.32194-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the PCII440FXState structure public, so it can be used out of
this source file. This will allow us to extract the IGD Passthrough
Host Bridge, which is a children of the TYPE_I440FX_PCI_DEVICE.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209095002.32194-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Missed during the refactor in commits 14a026dd58 and 0f25d865a,
this file is now only about the i440FX chipset.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191209095002.32194-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use RCU_READ_LOCK_GUARD and WITH_RCU_READ_LOCK_GUARD
to replace the manual rcu_read_(un)lock calls.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This device is only used by the PC machines. The pc.c file is
already big enough, with 2255 lines. By removing 113 lines of
it, we reduced it by 5%. It is now a bit easier to navigate
the file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This one-line function is not very helpful, so remove it
by inlining the call to qdev_connect_gpio_out_named().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By using the TYPE_* definitions for devices, we can:
- quickly find where devices are used with 'git-grep'
- easily rename a device (one-line change).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The irq number is unsigned; we reject negative values. But -1
is used for the isairq array, which is declared unsigned! And
since we have a definition for the number of ISA IRQs, use it.
Based on a patch by Philippe Mathieu-Daudé.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers of ioapic_init_gsi() provide a parent. We want new
uses to follow the same good practice and provide the parent
name, so do not make this optional: assert the parent name is
provided, and simplify the code.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both gsi_handler() and kvm_pc_gsi_handler() have the same content,
except one comment. Move the comment, and de-duplicate the code.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are needed by microvm too, so move them outside of PC-specific files.
With this patch, microvm.c need not include pc.h anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert the deprecated DPRINTF() macro to trace events.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add it to microvm as well, it is a generic property of the x86
architecture.
Suggested-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On x86, KVM needs some function from the PCI subsystem in order to set
up interrupt routes. Provide some stubs to support x86 machines that
lack PCI.
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the need to include i386/pc.h to get to the i8259 functions.
This is enough to remove the inclusion of hw/i386/pc.h from all non-x86
files.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The microvm machine type uses fw_cfg but lacks SMBIOS and ACPI. Do not
include the files if the symbol is not present in QEMU and remove
dependencies on machine-specific files.
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVMState struct is opaque, so provide accessors for the fields
that will be moved from current_machine to the accelerator. For now
they just forward to the machine object, but this will change.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The first machine property to fall is Xen's Intel integrated graphics
passthrough. The "-machine igd-passthru" option does not set anymore
a property on the machine object, but desugars to a GlobalProperty on
accelerator objects.
The setter is very simple, since the value ends up in a
global variable, so this patch also provides an example before the more
complicated cases that follow it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the "accel" property from MachineState, and instead desugar
"-machine accel=" to a list of "-accel" options.
This has a semantic change due to removing merge_lists from -accel.
For example:
- "-accel kvm -accel tcg" all but ignored "-accel kvm". This is a bugfix.
- "-accel kvm -accel thread=single" ignored "thread=single", since it
applied the option to KVM. Now it fails due to not specifying the
accelerator on "-accel thread=single".
- "-accel tcg -accel thread=single" chose single-threaded TCG, while now
it will fail due to not specifying the accelerator on "-accel
thread=single".
Also, "-machine accel" and "-accel" become incompatible.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Devices "ivshmem-plain" and "ivshmem-doorbell" support only MSI-X.
Config space register Interrupt Pin is zero. Device "ivshmem"
additionally supported legacy INTx, but it was removed in commit
5a0e75f0a9 "hw/misc/ivshmem: Remove deprecated "ivshmem" legacy
device". The commit left ivshmem_update_irq() behind. Since the
Interrupt Pin register is zero, the function does nothing. Remove it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191205203557.11254-1-armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It's been deprecated since QEMU v3.1. We've explicitly asked in the
deprecation message that people should speak up on qemu-devel in case
they are still actively using the bluetooth part of QEMU, but nobody
ever replied that they are really still using it.
I've tried it on my own to use this bluetooth subsystem for one of my
guests, but I was also not able to get it running anymore: When I was
trying to pass-through a real bluetooth device, either the guest did
not see the device at all, or the guest crashed.
Even worse for the emulated device: When running
qemu-system-x86_64 -bt device:keyboard
QEMU crashes once you hit a key.
So it seems like the bluetooth stack is not only neglected, it is
completely bitrotten, as far as I can tell. The only attention that
this code got during the past years were some CVEs that have been
spotted there. So this code is a burden for the developers, without
any real benefit anymore. Time to remove it.
Note: hw/bt/Kconfig only gets cleared but not removed here yet.
Otherwise there is a problem with the *-softmmu/config-devices.mak.d
dependency files - they still contain a reference to this file which
gets evaluated first on some build hosts, before the file gets
properly recreated. To avoid breaking these builders, we still need
the file around for some time. It will get removed in a couple of
weeks instead.
Message-Id: <20191120091014.16883-4-thuth@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It isn't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623844102.360005.12070225703151669294.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XSCOM bus is implemented with a QOM interface, which is mostly
generic from a CPU type standpoint, except for the computation of
addresses on the Pervasive Connect Bus (PCB) network. This is handled
by the pnv_xscom_pcba() function with a switch statement based on
the chip_type class level attribute of the CPU chip.
This can be achieved using QOM. Also the address argument is masked with
PNV_XSCOM_SIZE - 1, which is for POWER8 only. Addresses may have different
sizes with other CPU types. Have each CPU chip type handle the appropriate
computation with a QOM xscom_pcba() method.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623843543.360005.13996472463887521794.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since pnv_dt_xscom() is called from chip specific dt_populate() hooks,
it shouldn't have to guess the chip type in order to populate the
"compatible" property. Just pass the compat string and its size as
arguments.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623842430.360005.9513965612524265862.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since pnv_dt_xscom() is called from chip specific dt_populate() hooks,
it shouldn't have to guess the chip type in order to populate the "reg"
property. Just pass the base address and address size as arguments.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623841868.360005.17577624823547136435.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_chip_core_realize() function configures the XSCOM MMIO subregion
for each core of a single chip. The base address of the subregion depends
on the CPU type. Its computation is currently open-code using the
pnv_chip_is_powerXX() helpers. This can be achieved with QOM. Introduce
a method for this in the base chip class and implement it in child classes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623841311.360005.4705705734873339545.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_pic_print_info() callback checks the type of the chip in order
to forward to the request appropriate interrupt controller. This can
be achieved with QOM. Introduce a method for this in the base chip class
and implement it in child classes.
This also prepares ground for the upcoming interrupt controller of POWER10
chips.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623840755.360005.5002022339473369934.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We add an extra node to advertise power management on some machines,
namely powernv9 and powernv10. This is achieved by using the
pnv_is_power9() and pnv_is_power10() helpers.
This can be achieved with QOM. Add a method to the base class for
powernv machines and have it implemented by machine types that
support power management instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623839642.360005.9243510140436689941.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_dt_create() function generates different contents for the
"compatible" property of the root node in the DT, depending on the
CPU type. This is open coded with multiple ifs using pnv_is_powerXX()
helpers.
It seems cleaner to achieve with QOM. Introduce a base class for the
powernv machine and a compat attribute that each child class can use
to provide the value for the "compatible" property.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623839085.360005.4046508784077843216.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in small fix Greg spotted after posting]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It isn't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623838530.360005.15470128760871845396.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Service Interface (PSI) model has a chip_type class level
attribute, which is used to generate the content of the "compatible" DT
property according to the CPU type.
Since the PSI model already has specialized classes for each supported
CPU type, it seems cleaner to achieve this with QOM. Provide the content
of the "compatible" property with a new class level attribute.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623837974.360005.14706607446188964477.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC common area is mapped at a unique address on the system and
each OCC is assigned a segment to expose its sensor data :
-------------------------------------------------------------------------
| Start (Offset from | End | Size |Description |
| BAR2 base address) | | | |
-------------------------------------------------------------------------
| 0x00580000 | 0x005A57FF |150kB |OCC 0 Sensor Data Block|
| 0x005A5800 | 0x005CAFFF |150kB |OCC 1 Sensor Data Block|
| : | : | : | : |
| 0x00686800 | 0x006ABFFF |150kB |OCC 7 Sensor Data Block|
| 0x006AC000 | 0x006FFFFF |336kB |Reserved |
-------------------------------------------------------------------------
Maximum size is 1.5MB.
We could define a "OCC common area" memory region at the machine level
and sub regions for each OCC. But it adds some extra complexity to the
models. Fix the current layout with a simpler model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191211082912.2625-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PBA bridge unit (Power Bus Access) connects the OCC (On Chip
Controller) to the Power bus and System Memory. The PBA is used to
gather sensor data, for power management, for sleep states, for
initial boot, among other things.
The PBA logic provides a set of four registers PowerBus Access Base
Address Registers (PBABAR0..3) which map the OCC address space to the
PowerBus space. These registers are setup by the initial FW and define
the PowerBus Range of system memory that can be accessed by PBA.
The current modeling of the PBABAR registers is done under the common
XSCOM handlers. We introduce a specific XSCOM regions for these
registers and fix :
- BAR sizes and BAR masks
- The mapping of the OCC common area. It is common to all chips and
should be mapped once. We will address per-OCC area in the next
change.
- OCC common area is in BAR 3 on P8
Inspired by previous work of Balamuruhan S <bala24@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191211082912.2625-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some devices could be initialized in the instance_init handler but not
realized for configuration reasons. Nodes should not be added in the DT
for such devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191210135845.19773-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some PnvXScomInterface objects lie a bit deeper (PnvPBCQState) than
the first layer, so we need to loop on the whole object hierarchy to
catch them.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191210135845.19773-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
[dwg: Corrected error in comment]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spr TBU40 is used to set the upper 40 bits of the timebase
register, present on POWER5+ and later processors.
This register can only be written by the hypervisor, and cannot be read.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Utilisation of Resources Register (PURR) and Scaled
Processor Utilisation of Resources Register (SPURR) provide an estimate
of the resources used by the thread, present on POWER7 and later
processors.
Currently the [S]PURR registers simply count at the rate of the
timebase.
Preserve this behaviour but rework the implementation to store an offset
like the timebase rather than doing the calculation manually. Also allow
hypervisor write access to the register along with the currently
available read access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The virtual timebase register (VTB) is a 64-bit register which
increments at the same rate as the timebase register, present on POWER8
and later processors.
The register is able to be read/written by the hypervisor and read by
the supervisor. All other accesses are illegal.
Currently the VTB is just an alias for the timebase (TB) register.
Implement the VTB so that is can be read/written independent of the TB.
Make use of the existing method for accessing timebase facilities where
by the compensation is stored and used to compute the value on reads/is
updated on writes.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Same a POWER9, only the MMIO window changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER10 PSIHB controller is very similar to the one on POWER9. We
should probably introduce a common PnvPsiXive object.
The ESB page size should be changed to 64k when P10 support is ready.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is an empty shell with the XSCOM bus and cores. The chip controllers
will come later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The power7_set_irq() and power9_set_irq() functions set this but it is
never used actually. Modern Book3s compatible CPUs are only supported
by the pnv and spapr machines. They have an interrupt controller, XICS
for POWER7/8 and XIVE for POWER9, whose models don't require to track
IRQ input states at the CPU level.
Drop these lines to avoid confusion.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157548862861.3650476.16622818876928044450.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The correct way to do this is to deassert the input pins on the CPU side.
This is the case since a previous change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157548862298.3650476.1228720391270249433.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU is reset, QEMU makes sure no interrupt is pending by clearing
CPUPPCstate::pending_interrupts in ppc_cpu_reset(). In the case of a
complete machine emulation, eg. a sPAPR machine, an external interrupt
request could still be pending in KVM though, eg. an IPI. It will be
eventually presented to the guest, which is supposed to acknowledge it at
the interrupt controller. If the interrupt controller is emulated in QEMU,
either XICS or XIVE, ppc_set_irq() won't deassert the external interrupt
pin in KVM since it isn't pending anymore for QEMU. When the vCPU re-enters
the guest, the interrupt request is still pending and the vCPU will try
again to acknowledge it. This causes an infinite loop and eventually hangs
the guest.
The code has been broken since the beginning. The issue wasn't hit before
because accel=kvm,kernel-irqchip=off is an awkward setup that never got
used until recently with the LC92x IBM systems (aka, Boston).
Add a ppc_irq_reset() function to do the necessary cleanup, ie. deassert
the IRQ pins of the CPU in QEMU and most importantly the external interrupt
pin for this vCPU in KVM.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157548861740.3650476.16879693165328764758.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_ovec_diff(ov, old, new) has somewhat complex semantics. ov is set
to those bits which are in new but not old, and it returns as a boolean
whether or not there are any bits in old but not new.
It turns out that both callers only care about the second, not the first.
This is basically equivalent to a bitmap subset operation, which is easier
to understand and implement. So replace spapr_ovec_diff() with
spapr_ovec_subset().
Cc: Mike Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cedric Le Goater <clg@fr.ibm.com>
spapr_h_cas_compose_response() handles the last piece of the PAPR feature
negotiation process invoked via the ibm,client-architecture-support OF
call. Its only caller is h_client_architecture_support() which handles
most of the rest of that process.
I believe it was placed in a separate file originally to handle some
fiddly dependencies between functions, but mostly it's just confusing
to have the CAS process split into two pieces like this. Now that
compose response is simplified (by just generating the whole device
tree anew), it's cleaner to just fold it into
h_client_architecture_support().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cedric Le Goater <clg@fr.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Previously, spapr_build_fdt() constructed the device tree in a fixed
buffer of size FDT_MAX_SIZE. This is a bit inflexible, but more
importantly it's awkward for the case where we use it during CAS. In
that case the guest firmware supplies a buffer and we have to
awkwardly check that what we generated fits into it afterwards, after
doing a lot of size checks during spapr_build_fdt().
Simplify this by having spapr_build_fdt() take a 'space' parameter.
For the CAS case, we pass in the buffer size provided by SLOF, for the
machine init case, we continue to pass FDT_MAX_SIZE.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cedric Le Goater <clg@fr.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
PAPR allows the interrupt controller used on a POWER9 machine (XICS or
XIVE) to be selected by the guest operating system, by using the
ibm,client-architecture-support (CAS) feature negotiation call.
Currently, if the guest selects an interrupt controller different from the
one selected at initial boot, this causes the system to be reset with the
new model and the boot starts again. This means we run through the SLOF
boot process twice, as well as any other bootloader (e.g. grub) in use
before the OS calls CAS. This can be confusing and/or inconvenient for
users.
Thanks to two fairly recent changes, we no longer need this reboot. 1) we
now completely regenerate the device tree when CAS is called (meaning we
don't need special case updates for all the device tree changes caused by
the interrupt controller mode change), 2) we now have explicit code paths
to activate and deactivate the different interrupt controllers, rather than
just implicitly calling those at machine reset time.
We can therefore eliminate the reboot for changing irq mode, simply by
putting a call to spapr_irq_update_active_intc() before we call
spapr_h_cas_compose_response() (which gives the updated device tree to
the guest firmware and OS).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cedric Le Goater <clg@fr.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Make kvmppc_hint_smt_possible hint append helper well formed:
rename errp to errp_in, as it is IN-parameter here (which is unusual
for errp), rename function to be kvmppc_error_append_*_hint.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191127191434.20945-1-vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is useful to dump the saved contexts of the vCPUs : configuration
of the base END index of the vCPU and the Interrupt Pending Buffer
register, which is updated when an interrupt can not be presented.
When dumping the NVT table, we skip empty indirect pages which are not
necessarily allocated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-21-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When doing CAM line compares, fetch the block id from the interrupt
controller which can have set the PC_TCTXT_CHIPID field.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-20-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When PC_TCTXT_CHIPID_OVERRIDE is configured, the PC_TCTXT_CHIPID field
overrides the hardwired chip ID in the Powerbus operations and for CAM
compares. This is typically used in the one block-per-chip configuration
to associate a unique block id number to each IC of the system.
Simplify the model with a pnv_xive_block_id() helper and remove
'tctx_chipid' which becomes useless.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-19-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a vCPU is dispatched on a HW thread, its context is pushed in the
thread registers and it is activated by setting the VO bit in the CAM
line word2. The HW grabs the associated NVT, pulls the IPB bits and
merges them with the IPB of the new context. If interrupts were missed
while the vCPU was not dispatched, these are synthesized in this
sequence.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-18-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to resend missed interrupts when a vCPU context is
pushed on a HW thread.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-17-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is now unused.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-16-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the P9 Processor, the thread interrupt context registers of a CPU
can be accessed "directly" when by load/store from the CPU or
"indirectly" by the IC through an indirect TIMA page. This requires to
configure first the PC_TCTXT_INDIRx registers.
Today, we rely on the get_tctx() handler to deduce from the CPU PIR
the chip from which the TIMA access is being done. By handling the
TIMA memory ops under the interrupt controller model of each machine,
we can uniformize the TIMA direct and indirect ops under PowerNV. We
can also check that the CPUs have been enabled in the XIVE controller.
This prepares ground for the future versions of XIVE.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA region gives access to the thread interrupt context registers
of a CPU. It is mapped at the same address on all chips and can be
accessed by any CPU of the system. To identify the chip from which the
access is being done, the PowerBUS uses a 'chip' field in the
load/store messages. QEMU does not model these messages, instead, we
extract the chip id from the CPU PIR and do a lookup at the machine
level to fetch the targeted interrupt controller.
Introduce pnv_get_chip() and pnv_xive_tm_get_xive() helpers to clarify
this process in pnv_xive_get_tctx(). The latter will be removed in the
subsequent patches but the same principle will be kept.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE KVM devices now has an attribute to configure the number of
interrupt servers. This allows to greatly optimize the usage of the VP
space in the XIVE HW, and thus to start a lot more VMs.
Only set this attribute if available in order to support older POWER9
KVM.
The XIVE KVM device now reports the exhaustion of VPs upon the
connection of the first VCPU. Check that in order to have a chance
to provide a hint to the user.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478679392.67101.7843580591407950866.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICS-on-XIVE KVM devices now has an attribute to configure the number
of interrupt servers. This allows to greatly optimize the usage of the VP
space in the XIVE HW, and thus to start a lot more VMs.
Only set this attribute if available in order to support older POWER9 KVM
and pre-POWER9 XICS KVM devices.
The XICS-on-XIVE KVM device now reports the exhaustion of VPs upon the
connection of the first VCPU. Check that in order to have a chance to
provide a hint to the user.
`
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678846.67101.9660531022460517710.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE and XICS-on-XIVE KVM devices on POWER9 hosts can greatly reduce
their consumption of some scarce HW resources, namely Virtual Presenter
identifiers, if they know the maximum number of vCPUs that may run in the
VM.
Prepare ground for this by passing the value down to xics_kvm_connect()
and kvmppc_xive_connect(). This is purely mechanical, no functional
change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678301.67101.2717368060417156338.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA operations are performed on behalf of the XIVE IVPE sub-engine
(Presenter) on the thread interrupt context registers. The current
operations supported by the model are simple and do not require access
to the controller but more complex operations will need access to the
controller NVT table and to its configuration.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Andrew Jones