zicfiss has following instructions
- sspopchk: pops a value from shadow stack and compares with x1/x5.
If they dont match, reports a sw check exception with tval = 3.
- sspush: pushes value in x1/x5 on shadow stack
- ssrdp: reads current shadow stack
- ssamoswap: swaps contents of shadow stack atomically
sspopchk/sspush/ssrdp default to zimop if zimop implemented and SSE=0
If SSE=0, ssamoswap is illegal instruction exception.
This patch implements shadow stack operations for qemu-user and shadow
stack is not protected.
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-17-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
zicfiss introduces a new state ssp ("shadow stack register") in cpu.
ssp is expressed as a new unprivileged csr (CSR_SSP=0x11) and holds
virtual address for shadow stack as programmed by software.
Shadow stack (for each mode) is enabled via bit3 in *envcfg CSRs.
Shadow stack can be enabled for a mode only if it's higher privileged
mode had it enabled for itself. M mode doesn't need enabling control,
it's always available if extension is available on cpu.
This patch also implements helper bcfi function which determines if bcfi
is enabled at current privilege or not.
Adds ssp to migration state as well.
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-12-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
zicfilp protects forward control flow (if enabled) by enforcing all
indirect call and jmp must land on a landing pad instruction `lpad`. If
target of an indirect call or jmp is not `lpad` then cpu/hart must raise
a sw check exception with tval = 2.
This patch implements the mechanism using TCG. Target architecture branch
instruction must define the end of a TB. Using this property, during
translation of branch instruction, TB flag = FCFI_LP_EXPECTED can be set.
Translation of target TB can check if FCFI_LP_EXPECTED flag is set and a
flag (fcfi_lp_expected) can be set in DisasContext. If `lpad` gets
translated, fcfi_lp_expected flag in DisasContext can be cleared. Else
it'll fault.
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-7-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
zicfilp introduces a new state elp ("expected landing pad") in cpu.
During normal execution, elp is idle (NO_LP_EXPECTED) i.e not expecting
landing pad. On an indirect call, elp moves LP_EXPECTED. When elp is
LP_EXPECTED, only a subsquent landing pad instruction can set state back
to NO_LP_EXPECTED. On reset, elp is set to NO_LP_EXPECTED.
zicfilp is enabled via bit2 in *envcfg CSRs. Enabling control for M-mode
is in mseccfg CSR at bit position 10.
On trap, elp state is saved away in *status.
Adds elp to the migration state as well.
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-4-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This commit allows program to write textra trigger CSR for type 2, 3, 6
triggers. In this preliminary patch, the textra.MHVALUE and the
textra.MHSELECT fields are allowed to be configured. Other fields, such
as textra.SBYTEMASK, textra.SVALUE, and textra.SSELECT, are hardwired to
zero for now.
For textra.MHSELECT field, the only legal values are 0 (ignore) and 4
(mcontext). Writing 1~3 into textra.MHSELECT will be changed to 0, and
writing 5~7 into textra.MHSELECT will be changed to 4. This behavior is
aligned to RISC-V SPIKE simulator.
Signed-off-by: Alvin Chang <alvinga@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240826024657.262553-2-alvinga@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
QEMU only calculates dummy cycles and instructions, so there is no
actual means to stop the icount in QEMU. Hence this patch merely adds
the functionality of accessing the cfg registers, and cause no actual
effects on the counting of cycle and instret counters.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Kaiwen Xue <kaiwenx@rivosinc.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-5-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the definitions for ISA extension smcntrpmf.
Signed-off-by: Kaiwen Xue <kaiwenx@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-4-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Based on the priv-1.13.0, add the exception codes for Software-check and
Hardware-error.
Signed-off-by: Fea.Wang <fea.wang@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240606135454.119186-6-fea.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Based on privileged spec 1.13, the RV32 needs to implement MEDELEGH
and HEDELEGH for exception codes 32-47 for reserving and exception codes
48-63 for custom use. Add the CSR number though the implementation is
just reading zero and writing ignore. Besides, for accessing HEDELEGH, it
should be controlled by mstateen0 'P1P13' bit.
Signed-off-by: Fea.Wang <fea.wang@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240606135454.119186-5-fea.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Based on privilege 1.13 spec, there should be a bit56 for 'P1P13' in
mstateen0 that controls access to the hedeleg.
Signed-off-by: Fea.Wang <fea.wang@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Weiwei Li <liwei1518@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240606135454.119186-4-fea.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Qemu maps IRQs 0:15 for core interrupts and 16 onward for
guest interrupts which are later translated to hgiep in
`riscv_cpu_set_irq()` function.
With virtual IRQ support added, software now can fully
use the whole local interrupt range without any actual
hardware attached.
This change moves the guest interrupt range after the
core local interrupt range to avoid clash.
Fixes: 1697837ed9 ("target/riscv: Add M-mode virtual interrupt and IRQ filtering support.")
Fixes: 40336d5b1d ("target/riscv: Add HS-mode virtual interrupt and IRQ filtering support.")
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240520125157.311503-3-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current semihost exception number (16) is a reserved number (range
[16-17]). The upcoming double trap specification uses that number for
the double trap exception. Since the privileged spec (Table 22) defines
ranges for custom uses change the semihosting exception number to 63
which belongs to the range [48-63] in order to avoid any future
collisions with reserved exception.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240422135840.1959967-1-cleger@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
vxrm and vxsat have been moved into a special register vcsr since
RVV v1.0. So remove them from FCSR for vector 1.0.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240130110945.486-1-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The debug Sdtrig extension defines an CSR "mcontext". This commit
implements its predicate and read/write operations into CSR table.
Its value is reset as 0 when the trigger module is reset.
Signed-off-by: Alvin Chang <alvinga@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231219123244.290935-1-alvinga@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change adds support for inserting virtual interrupts from M-mode
into S-mode using mvien and mvip csrs. IRQ filtering is a use case of
this change, i-e M-mode can stop delegating an interrupt to S-mode and
instead enable it in MIE and receive those interrupts in M-mode and then
selectively inject the interrupt using mvien and mvip.
Also, the spec doesn't mandate the interrupt to be actually supported
in hardware. Which allows M-mode to assert virtual interrupts to S-mode
that have no connection to any real interrupt events.
This is defined as part of the AIA specification [0], "5.3 Interrupt
filtering and virtual interrupts for supervisor level".
[0]: https://github.com/riscv/riscv-aia/releases/download/1.0/riscv-interrupts-1.0.pdf
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231016111736.28721-6-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Svadu specification updated the name of the *envcfg bit from
HADE to ADUE.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230816141916.66898-1-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
As per the specification, in 64-bit, if any of the pte reserved bits
60-54 is set an exception should be triggered (see 4.4.1, "Addressing and
Memory Protection"). In addition, we must check the napot/pbmt bits are
not set if those extensions are not active.
Reported-by: Andrea Parri <andrea@rivosinc.com>
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230420150220.60919-1-alexghiti@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The pointer masking is the only extension that directly use status.
The vector or float extension uses the status in an indirect way.
Replace the pointer masking extension special status fields with
the general status.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-Id: <20230324143031.1093-3-zhiwei_liu@linux.alibaba.com>
[rth: Add a typedef for the enum]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Tested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230325105429.1142530-3-richard.henderson@linaro.org>
Message-Id: <20230412114333.118895-3-richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
PRV_H has no real meaning, but just a reserved privilege mode currently.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230407014743.18779-3-liweiwei@iscas.ac.cn>
[ Changes by AF:
- Convert one missing use of PRV_H
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fix formats for multi-lines comments.
Add spaces around single line comments(after "/*" and before "*/").
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230405085813.40643-4-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently we only use the env->virt to encode the virtual mode enabled
status. Let's make it a bool type.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Message-ID: <20230325145348.1208-1-zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230327080858.39703-6-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add encode, trans* functions and helper functions support for Zcmt
instrutions.
Add support for jvt csr.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230307081403.61950-8-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add ext_svadu property
Add HADE field in *envcfg:
* menvcfg.HADE is read-only zero if Svadu is not implemented.
* henvcfg.HADE is read-only zero if menvcfg.HADE is zero.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230224040852.37109-4-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Smstateen extension specifies a mechanism to close
the potential covert channels that could cause security issues.
This patch adds the CSRs defined in the specification and
the corresponding predicates and read/write functions.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221016124726.102129-2-mchitale@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
tinfo.info:
One bit for each possible type enumerated in tdata1.
If the bit is set, then that type is supported by the currently
selected trigger.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-Id: <20220909134215.1843865-6-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
sideleg and sedeleg csrs are not part of riscv isa spec
anymore, these csrs were part of N extension which
is removed from the riscv isa specification.
These commits removed all traces of these csrs from
riscv spec (https://github.com/riscv/riscv-isa-manual) -
commit f8d27f805b65 ("Remove or downgrade more references to N extension (#674)")
commit b6cade07034d ("Remove N extension chapter for now")
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220824145255.400040-1-rpathak@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Sscofpmf ('Ss' for Privileged arch and Supervisor-level extensions,
and 'cofpmf' for Count OverFlow and Privilege Mode Filtering)
extension allows the perf to handle overflow interrupts and filtering
support. This patch provides a framework for programmable
counters to leverage the extension. As the extension doesn't have any
provision for the overflow bit for fixed counters, the fixed events
can also be monitoring using programmable counters. The underlying
counters for cycle and instruction counters are always running. Thus,
a separate timer device is programmed to handle the overflow.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221701.41932-2-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
vstimecmp CSR allows the guest OS or to program the next guest timer
interrupt directly. Thus, hypervisor no longer need to inject the
timer interrupt to the guest if vstimecmp is used. This was ratified
as a part of the Sstc extension.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221357.41070-4-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
stimecmp allows the supervisor mode to update stimecmp CSR directly
to program the next timer interrupt. This CSR is part of the Sstc
extension which was ratified recently.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221357.41070-3-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The latest AIA draft v0.3.0 defines a relatively simpler scheme for
default priority assignments where:
1) local interrupts 24 to 31 and 48 to 63 are reserved for custom use
and have implementation specific default priority.
2) remaining local interrupts 0 to 23 and 32 to 47 have a recommended
(not mandatory) priority assignments.
We update the default priority table and hviprio mapping as-per above.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220616031543.953776-3-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Based on architecture review committee feedback, the [m|s|vs]seteienum,
[m|s|vs]clreienum, [m|s|vs]seteipnum, and [m|s|vs]clreipnum CSRs are
removed in the latest AIA draft v0.3.0 specification.
(Refer, https://github.com/riscv/riscv-aia/releases/tag/0.3.0-draft.31)
These CSRs were mostly for software convenience and software can always
use [m|s|vs]iselect and [m|s|vs]ireg CSRs to update the IMSIC interrupt
file bits.
We update the IMSIC CSR emulation as-per above to match the latest AIA
draft specification.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220616031543.953776-2-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
As per the privilege specification v1.11, mcountinhibit allows to start/stop
a pmu counter selectively.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220620231603.2547260-6-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- add SEED CSR which must be accessed with a read-write instruction:
A read-only instruction such as CSRRS/CSRRC with rs1=x0 or CSRRSI/CSRRCI
with uimm=0 will raise an illegal instruction exception.
- add USEED, SSEED fields for MSECCFG CSR
Co-authored-by: Ruibo Lu <luruibo2000@163.com>
Co-authored-by: Zewen Ye <lustrew@foxmail.com>
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220423023510.30794-13-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V privileged specification v1.12 defines few execution
environment configuration CSRs that can be used enable/disable
extensions per privilege levels.
Add the basic support for these CSRs.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220303185440.512391-6-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V privileged specification v1.12 introduced a mconfigptr
which will hold the physical address of a configuration data
structure. As Qemu doesn't have a configuration data structure,
is read as zero which is valid as per the priv spec.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220303185440.512391-5-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- add PTE_PBMT bits: It uses two PTE bits, but otherwise has no effect on QEMU, since QEMU is sequentially consistent and doesn't model PMAs currently
- add PTE_PBMT bit check for inner PTE
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220204022658.18097-6-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- add PTE_N bit
- add PTE_N bit check for inner PTE
- update address translation to support 64KiB continuous region (napot_bits = 4)
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220204022658.18097-4-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Highest bits of PTE has been used for svpbmt, ref: [1], [2], so we
need to ignore them. They cannot be a part of ppn.
1: The RISC-V Instruction Set Manual, Volume II: Privileged Architecture
4.4 Sv39: Page-Based 39-bit Virtual-Memory System
4.5 Sv48: Page-Based 48-bit Virtual-Memory System
2: https://github.com/riscv/virtual-memory/blob/main/specs/663-Svpbmt-diff.pdf
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Liu Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220204022658.18097-2-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V AIA specification extends RISC-V local interrupts and
introduces new CSRs. This patch adds defines for the new AIA CSRs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20220204174700.534953-8-anup@brainfault.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The hgeie and hgeip CSRs are required for emulating an external
interrupt controller capable of injecting virtual external interrupt
to Guest/VM running at VS-level.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20220204174700.534953-4-anup@brainfault.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
A hypervisor can optionally take guest external interrupts using
SGEIP bit of hip and hie CSRs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20220204174700.534953-3-anup@brainfault.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220120122050.41546-23-zhiwei_liu@c-sky.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The csrs are accessed through function pointers: we add 128-bit read
operations in the table for three csrs (writes fallback to the
64-bit version as the upper 64-bit information is handled elsewhere):
- misa, as mxl is needed for proper operation,
- mstatus and sstatus, to return sd
In addition, we also add read and write accesses to the machine and
supervisor scratch registers.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Co-authored-by: Fabien Portas <fabien.portas@grenoble-inp.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-19-frederic.petrot@univ-grenoble-alpes.fr
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211210075704.23951-11-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211210075704.23951-10-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211210075704.23951-6-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211210075704.23951-4-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is no need to "force an hs exception" as the current privilege
level, the state of the global ie and of the delegation registers should
be enough to route the interrupt to the appropriate privilege level in
riscv_cpu_do_interrupt. The is true for both asynchronous and
synchronous exceptions, specifically, guest page faults which must be
hardwired to zero hedeleg. As such the hs_force_except mechanism can be
removed.
Signed-off-by: Jose Martins <josemartins90@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211026145126.11025-3-josemartins90@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Deepak Gupta