Bilinear applies to all renderer
* Common code done in GSVertexTrace
* Extend it with forced but sprite (trade-off between linear/upscale glitches)
* Linux GUI option was moved at the top with the renderer selection
Trilinear is moved to OGL hack
close#1837
Thanks to Flatout for the review and feedback.
It will take care to update the Window GUI :)
Previously, when F8 was triggered multiple times in a single second, the latest captured image would replace the previous captured one as it has the same name as the previous image.
The following patch detects such cases and adds a number along with the filename when new image capture is requested under the same time as the previous capture.
Code can be enabled with "wrap_gs_mem = 1". Code only allow a single shared memory but
I don't think we need more anyway.
Linux only, Kernel panic expected with the HW renderer.
Fix FMV on Silent Hill 3 with the SW renderer
* Add full PMODE register to replace slbg/mmod
* Add full EXTBUF register (will allow to emulate write feedback)
* Add a third source (which will actually be the destination of the
write feedback)
* Always do +1 before the draw call
* Prefix texture name with i (as input) to keep them before the FB
Goal is to ensure that all renderers share the same draw call value.
At higher resolutions it takes too much time to save a screenshot at the
maximum compression level. So let's allow the user to set the
compression level.
This re-uses the png_compression_level setting. The default compression
level is 1 for speed, but if the user wishes to increase the compression
level (without using an external tool) and doesn't mind if the
screenshot takes more time to save then they can increase the
compression level up to a maximum of 9 (which can take quite a while).
Fixes#1527.
In file included from GSRenderer.cpp:23:0:
GSRenderer.h: In constructor ‘GSRenderer::GSRenderer()’:
GSRenderer.h:58:12: warning: ‘GSRenderer::m_dev’ will be initialized after [-Wreorder]
GSDevice* m_dev;
^
GSRenderer.h:52:13: warning: ‘GSVector2i GSRenderer::m_real_size’ [-Wreorder]
GSVector2i m_real_size;
^
GSRenderer.cpp:32:1: warning: when initialized here [-Wreorder]
If baseline and display rectangle offsets differ by small values then consider the status of frame memory offsets, prevents blurring on Tenchu: Fatal Shadows, Worms 3D, ProStroke Golf, Vexx
Fixes games like Time Crisis 2/3, which use two half-width display
rectangles placed side by side in split screen mode by using different
DISPLAY.DX values.
* Silent Hill 2 doesn't need the CRC hack
* GSRenderer: no need to explicitly set bottom value for r.
* Texture Cache: Removed a check which couldn't possibly enter true
branch.
Try to avoid random black screen frame
v2: don't force the preload hack on the frame
It creates a ghost image over FMV
v3: support offset within a frame
Valid values for png_compression_level are from 0 (no compression) to 9
(max compression). The default is 1.
v2: Use zlib Z_BEST_SPEED (1) and Z_BEST_COMPRESSION (9) defines.
Both the Linux and Windows config dialogs now have a TV Shaders combobox,
so the F7 toggle can be made temporary. This makes the hotkey behaviour
consistent with all the other hotkeys.
A couple of useless members were removed too.
Also fix wnd initialization
Coverity:
CID 146955 (#1 of 1): Uninitialized pointer read (UNINIT)
18. uninit_use: Using uninitialized value wnd[i].
This is the internal resolution which GSdx uses and recording at this resolution
is optimal, i.e. without any dumb scaling, with all relevant pixels and without
redundant pixels.
The resulting clip still doesn't have the correct aspect ratio set, but that's
just a property which can be set to the clip afterwards, which is where the DAR
becomes useful. Since it's usually anamorphic, when muxing later with the audio
use the DAR to set the playback aspect ratio.
Before this patch, when recording Progressive (frame) mode, it recorded all
the frames correctly but set the clip's fps property to 25/29.97, so when
played back it played at half the speed (but was fine when played at double speed).
This patch does not affect the number of frames recorded per second, but rather
only sets the resulting clip fps property to the correct one (double than before).
Also fixes a bug that in a non-managed window in progressive mode, the title
displayed "200%" speed when it should have displayed 100% speed.
Fixes#832
Gregory Hainaut