Without this, the code added in ac28b89 misbehaves and considers
AArch64 netplay clients to not have hardware FMA support, telling
all clients to disable FMA support, which causes a desync between
x64 and AArch64 due to JitArm64 not being able to disable FMA support.
Fixes a regression from 5.0-12066, where setting the GFXBackend variable
to one other than the current global backend would crash Dolphin upon
launching the game.
fcmpX only updates the FPCC bits, not the C bit.
This was already correctly implemented in the interpreter.
Not known to affect any games, but affects a hardware test.
This fixes bounding box shaders failing to compile under Vulkan, due to
differences between GLSL and HLSL in the return value of vector
comparisons and what types these functions accept. I included all() for
the sake of completeness.
At higher resolutions, our bounding box dimensions end up being
slightly larger than original hardware in some cases. This is not
necessarily wrong, it's just an artifact of rendering at a higher
resolution, due to bringing out detail that wouldn't have appeared on
original hardware. It causes a texel to fall partially on what would
have been a single pixel at native resolution, resulting in the
coordinates getting bumped up to the next valid value. In many cases,
these slightly larger bounding boxes are perfectly fine, as games don't
hard-code expected dimensions. It is problematic in Paper Mario TTYD
though, for a somewhat complicated reason.
Paper Mario TTYD frequently uses EFB copies to pre-render a bunch of
animation frames for a character sprite (especially in Chapter 2), so
that it can then render 100 or more of them without bringing the
GameCube to its knees. Based on my observation, the game seems to set
aside a region of memory to store these EFB copies. This region is
obviously fairly small, as the GameCube only has 24MB of RAM. There are
2 rooms in Chapter 2 where you fight a horde of as many as 100 Jabbies,
which are also rendered using EFB copies, so in this room the game ends
up making 130(!) EFB copies just for Puni and Jabbi sprites. This seems
to nearly fill the region of memory it set aside for them.
Unfortunately, our slightly larger bounding boxes at higher resolutions
results in overflowing this memory, causing very strange behavior. Some
EFB copies partially overlap game state, resulting in reading it as a
garbage RGB5A3 texture that constantly changes. Others apparently
somehow trigger a corner case in our persistent buffer mapping, causing
them to partially overwrite earlier EFB copies.
What this change does is only include the screen coordinates that align
with the equivalent native resolution pixel centers, which generally
results in the bounding boxes being more in line with original
hardware. It isn't perfect, but it's enough to fix Paper Mario TTYD's
Jabbi rooms by avoiding the buffer overflow. Notably, it is more
accurate at odd resolutions than at even resolutions. Native resolution
is completely unaffected by this change, as should be the case. This
change may also have a small positive impact on shader performance at
higher resolutions, as there will be less atomic operations performed.
Not doing this can cause desyncs when TASing. (I don't know
how common such desyncs would be, though. For games that
don't change rounding modes, they shouldn't be a problem.)
When I added the software FMA path in 2c38d64 and made us use
it when determinism is enabled, I was assuming that either the
performance impact of software FMA wouldn't be too large or CPUs
that were too old to have FMA instructions were too slow to run
Dolphin well anyway. This was wrong. To give an example, the
netplay performance went from 60 FPS to 30 FPS in one case.
This change makes netplay clients negotiate whether FMA should
be used. If all clients use an x64 CPU that supports FMA, or
AArch64, then FMA is enabled, and otherwise FMA is disabled.
In other words, we sacrifice accuracy if needed to avoid massive
slowdown, but not otherwise. When not using netplay, whether to
enable FMA is simply based on whether the host CPU supports it.
The only remaining case where the software FMA path gets used
under normal circumstances is when an input recording is created
on a CPU with FMA support and then played back on a CPU without.
This is not an especially common scenario (though it can happen),
and TASers are generally less picky about performance and more
picky about accuracy than other users anyway.
With this change, FMA desyncs are avoided between AArch64 and
modern x64 CPUs (unlike before 2c38d64), but we do get FMA
desyncs between AArch64 and old x64 CPUs (like before 2c38d64).
This desync can be avoided by adding a non-FMA path to JitArm64 as
an option, which I will wait with for another pull request so that
we can get the performance regression fixed as quickly as possible.
https://bugs.dolphin-emu.org/issues/12542
Back when I wrote this code, I believe I set it to use a custom path
so that the cache would end up in a directory which Android considers
to be a cache directory. But nowadays the directory which Dolphin's
C++ code considers to be the cache directory is such a directory,
so there's no longer any reason to override the default path.
progressMessage can have the invalid value of 0. That
progressMessage was being used for the thread name was
a typo anyway – it's supposed to use progressTitle.
this prevented some devices from being recreated correctly, as they were exclusive (e.g. DInput Joysticks)
This is achieved by calling Settings::ReleaseDevices(), which releases all the UI devices shared ptrs.
If we are the host (Qt) thread, DevicesChanged() is now called in line, to avoid devices being hanged onto by the UI.
For this, I had to add a method to check whether we are the Host Thread to Qt.
Avoid calling ControllerInterface::RefreshDevices() from the CPU thread if the emulation is running
and we manually refresh devices from Qt, as that is not necessary anymore.
Refactored the way IOWindow lists devices to make it clearer and hold onto disconnected devices.
There were so many issues with the previous code:
-Devices changes would not be reflected until the window was re-opened
-If there was no default device, it would fail to select the device at index 0
-It could have crashed if we had 0 devices
-The default device was not highlighted as such
Léo Lam