scsi-block is a new device that supports device passthrough of Linux
block devices (i.e. /dev/sda, not /dev/sg0). It uses SG_IO for commands
other than I/O commands, and regular AIO read/writes for I/O commands.
Besides being simpler to configure (no mapping required to scsi-generic
device names), this removes the need for a large bounce buffer and,
in the future, will get scatter/gather support for free from scsi-disk.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The request restart mechanism is generic and could be reused for
scsi-generic. In the meanwhile, pushing it to SCSIDevice avoids
that scsi_dma_restart_bh looks at SCSIGenericReqs when working on
a scsi-block device.
The code is the same that is already in hw/scsi-disk.c, with
the type flags replaced by req->cmd.mode and a more generic way to
requeue SCSI_XFER_NONE commands.
I also added a missing call to qemu_del_vm_change_state_handler.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In some cases a request may be canceled before the completion callback
runs. Keep a reference to the request between starting an AIO operation
and the corresponding scsi_req_cancel or scsi_*_complete.
When a request has to be retried, the request can be dropped because
scsi_dma_restart_bh only looks at requests that are enqueued. As such,
they always have at least a reference.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Otherwise, if cancellation is "faked" by the AIO layer and goes
through qemu_aio_flush, the whole request is completed synchronously
during scsi_req_cancel.
Using the enqueued flag would work here, but not in the next patches,
so I'm introducing a new io_canceled flag. That's because scsi_req_data
is a synchronous callback and the enqueued flag might be reset by the
time it returns. scsi-disk cannot unref the request until after calling
scsi_req_data.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This will let scsi-block choose between passthrough and emulation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Also delete a stale occurrence of SCSIReqOps inside SCSIDeviceInfo.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The field is only in scsi-disk for now. Moving it up to SCSIDevice makes
it easier to reuse the scsi-generic reqops elsewhere.
At the same time, make scsi-generic get max_lba from snooped READ CAPACITY
commands as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Set s->removable, s->qdev.blocksize and s->qdev.type in the callers
of scsi_initfn.
With this in place, s->qdev.type is allowed, and we can just reuse it
as the first byte in VPD data (just like we do in standard INQUIRY data).
Also set s->removable is set consistently and we can use it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This field is redundant, and having it makes it more complicated
to share reqops between the upcoming scsi-block and scsi-generic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Same as for scsi-generic, avoid duplication even if it causes longer
lines.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of "guessing" the block size when there is no medium in the
drive, wait for the guest to send a READ CAPACITY command and snoop
it from there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass down the host status so that failing transport can be detected
by the guest. Similar treatment of host status could be done in
virtio-blk, too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A succeeding ioctl does not imply that the SCSI command succeeded.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is not needed anymore, since asynchronous ioctls were introduced
by commit 221f715 (new scsi-generic abstraction, use SG_IO, 2009-03-28).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It is not needed, because s->bs is already stored in SCSIDevice, and
can be reached from the conf.bs member.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Flush does not go anymore through scsi_disk_emulate_command.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested by the Windows Logo Kit SCSI Compliance test. From SBC-3, paragraph
5.25: "The LOGICAL BLOCK ADDRESS field shall be set to zero if the PMI
bit is set to zero. If the PMI bit is set to zero and the LOGICAL BLOCK
ADDRESS field is not set to zero, then the device server shall terminate
the command with CHECK CONDITION status with the sense key set to ILLEGAL
REQUEST and the additional sense code set to INVALID FIELD IN CDB".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This also requires little more than adding the new argument to
scsi_device_find, and the qdev property. All devices by default
end up on channel 0.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This only requires changes in two places: in SCSIBus, we need to look
for a free LUN if somebody creates a device with a pre-existing scsi-id
but the default LUN (-1, meaning "search for a free spot"); in vSCSI,
we need to actually parse the LUN according to the SCSI spec.
For vSCSI, max_target/max_lun are set according to the logical unit
addressing format in SAM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Change the devs array into a linked list, and add a scsi_device_find
function to navigate the children list instead. This lets the SCSI
bus use more complex addressing, and HBAs can talk to the correct device
when there are multiple LUNs per target.
scsi_device_find may return another LUN on the same target if none is
found that matches exactly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
SCSI buses will need to read the children list first-to-last. This
requires using a QTAILQ, because hell breaks loose if you just try
inserting at the tail (thus reversing the order of all existing
visits from last-to-first to first-to-tail).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds support for media change notification via the GET EVENT STATUS
NOTIFICATION command, used by Linux versions 2.6.38 and newer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds to scsi-disk the missing mode page 0x01 for both disk
and CD-ROM drives, and mode page 0x0e for CD drives only.
A few offsets were wrong in atapi.c. Also change the 2Ah mode page to
expose DVD media read capabilities in the IDE cdrom. This lets you run
dvd+rw-mediainfo on the virtual DVD drives.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A small refactoring of the MODE SENSE implementation in scsi-disk.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a few stub implementations for MMC commands to
scsi-disk, to be filled in later in the series. It also adds to
scsi-defs.h constants for commands implemented by ide/atapi.c,
when missing.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Building on the previous patch, this one adds a media change callback
to scsi-disk.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reporting media change events via unit attention sense codes requires
a small state machine: first report "NO MEDIUM", then report "MEDIUM MAY
HAVE CHANGED". Unfortunately there is no good hooking point for the
device to notice that its pending unit attention condition has been
reported. This patch reworks the generic machinery to add one.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The first two bytes (after the 8-byte ATAPI header) are the mode page
number and the number of bytes after the length field itself. Make
this clear in the code.
The AUDIO_CTL page was filled with wrong values. It is not anymore in
MMC, but at least keep the values sane.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
As a complement to the previous patch, move definitions for GET EVENT
STATUS NOTIFICATION from the two functions to scsi-defs.h.
The NCR_* constants are just bit values corresponding to the ENC_*
values, with no offsets even, so keep just one copy.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The definitions in ide/internal.h are duplicates, since ATAPI commands
actually come from SCSI. Use the ones in scsi-defs.h and move the
missing ones there. Two exceptions:
- MODE_PAGE_WRITE_PARMS conflicts with the "flexible disk geometry"
page in scsi-disk.c. It is unused, so pick the latter.
- GPCMD_* is left in ide/internal.h, at least for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This also fixes a bug with the old version: QMP would invert device id
and vendor id. This would look ok on HMP because it was printing
"device:vendor" instead of "vendor:device".
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Please, note that some of the code supporting memory statistics is
still around (eg. virtio_balloon_receive_stats() and reset_stats()).
Also, the qmp_query_balloon() function is synchronous and thus doesn't
make any use of the (not fully working) monitor's asynchronous command
support (the old non-qapi implementation did).
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Windows 7 may use the same stream number for input and output.
Current code will confuse streams.
Changes since v1:
- keep running_compat[] for migration version 1
- add running_real[] for migration version 2
Signed-off-by: Marc-Andr? Lureau <marcandre.lureau@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
Windows 7 may use the same stream number for input and output.
That will result in lot of garbage on playback.
The hardcoded value of 4 needs to be in sync with GCAP streams
description and IN/OUT registers.
Signed-off-by: Marc-Andr? Lureau <marcandre.lureau@redhat.com>
Signed-off-by: malc <av1474@comtv.ru>
update init_qxl_ram to reset update_surface to 0. This fixes one case
of breakage when installing an old driver in a vm that had a new driver
installed. The newer driver would know about surface creation and would
change update_surface to !=0, then a reset would happen, all surfaces
are destroyed, then the old driver is initialized and issues an
UPDATE_AREA, and spice server aborts on invalid surface.
RHBZ: 690427
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
(1) If the guest cursor command is empty, don't reload it after migration.
(2) Cleaning the guest cursor when it is released by
the spice server. In addition, explicitly reset the
cursor in spice upon destroying the primary surface
(was done by spice-server implicitly). This will prevent
access to pci memory that was released.
RHBZ: 744518
Signed-off-by: Yonit Halperin <yhalperi@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This was only a best-effort attempt, by far not guaranteed to have an
effect. Drop it so that also no direct pthread usage remain in the
device model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Use QEMU thread API instead of pthread directly. We still need to get
rid of pthread_yield, though, to drop pthread.h inclusion.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix incorrect order of arguments, letting writes to NVRAM succeed.
It looks like guests never write to the device, only read from it, since the bug
originates back to 819385c58b.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit 63ffb564 broke floppy devices specified on the command line like
-drive file=...,if=none,id=floppy -global isa-fdc.driveA=floppy because it
relies on drive_get() which works only with -fda/-drive if=floppy.
This patch resembles what we're already doing for IDE, i.e. remember the floppy
device that was created and use that to extract the BlockDriverStates where
needed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The floppy device was broken by commit 212ec7ba (fdc: Convert to
isa_register_portio_list). While the old interface provided the port number
relative to the floppy drive's io_base, the new one provides the real port
number, so we need to apply a bitmask now to get the register number.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The synchronous .bdrv_flush callback doesn't exist any more and a device really
shouldn't poke into the block layer internals anyway. All drivers are supposed
to have a correctly working bdrv_flush, so let's just hard-code this.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
irq_target array saving/loading is in the wrong loop.
Version bump.
Signed-off-by: Dmitry Koshelev <karaghiozis@gmail.com>
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
The OMAP2430 version of the omap-gpio device has five GPIO modules,
not four like the other OMAP2 versions; wire up the fifth module's
IRQ line correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Now the function returned errno, so it is better the new name.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
QEMUFile * is only intended for migration nowadays. Using it for
anything else just adds pain and a layer of buffers for no good
reason.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
This allows to drop various stubs and move the i8359 into hwlib.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This key cleanup step requires to move the IRQ debugging bit from
i8259_set_irq directly to the per-PIC pic_set_irq, to pass the PIC
parameters (I/O base, ELCR address and mask, master/slave mode) as
qdev properties, and to interconnect the PICs with their environment via
GPIO pins.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Introduce a reference to the slave PIC for the few cases we need to
access it without a proper pointer at hand and drop PicState2. We could
even live without slave_pic if we had a better way of modeling the
cascade bus the PICs are attached to (in addition to the ISA bus).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reflects how real PICs indentify their role (in non-buffered mode):
Pass the state of the /SP input on pic_init and use it instead of
pics_state to differentiate between master and slave mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
There is nothing in the i8259 spec that justifies the special
pic_intack_read. At least the Linux PREP kernels configure the PICs
properly so that pic_read_irq returns identical values, and setting
read_reg_select in PIC0 cannot be derived from any special i8259 mode.
So switch ppc_prep to pic_read_irq and drop the now unused PIC code.
CC: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This was probably never used so far: According to the spec, polling
means ack'ing the pending IRQ and setting its corresponding bit in isr.
Moreover, we have to signal a pending IRQ via bit 7 of the returned
value, and we must not return a spurious IRQ if none is pending.
This implements the poll command without the help of pic_poll_read which
is left untouched as pic_intack_read is still using it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This converts pic_update_irq to work against a single PIC instead of the
complete cascade. Along this change, the required update after
pic_set_irq1 is now moved into that function.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The ELCR is actually part of the chipset but we model it here for
simplicity reasons. The PIIX3 clears the ELCR on reset, which was once
broken by 4dbe19e181. Fix this by splitting up pic_init_reset from
pic_reset and clearing the register in the latter.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
MIPS and PPC users of the i8259 output signal expect us to report state
updates also after reset. As no consumer (including the master PIC) can
misinterpret the deassert as an activation event, it is safe to simply
update the IRQ state after reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As we want to move the IRQ update to pic_intack, ordering matters: the
slave ack must be executed before the master ack to avoid missing
further pending slave IRQs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If pic_poll_read finds no pending IRQ and return a spurious one instead,
no PIC state is changed, thus we do not need to call pic_update_irq.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As a first step towards more generic master-slave support, remove
parent_irq in favor of a per-PIC output interrupt line. The slave's
line is attached to IRQ2 of the master, but it remains unused for now.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We are about to call the latter from the former. No functional changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The compiler is smarter in choosing the right optimization.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The master PIC is connected to the LINTIN0 of the APICs. As the APIC
currently does not track the state of that line, we have to ask the PIC
to reinject its IRQ after the CPU picked up an event from the APIC.
This introduces pic_get_output to read the master PIC IRQ line state
without changing it. The APIC uses this function to decide if a PIC IRQ
should be reinjected on apic_update_irq. This reflects better how the
real hardware works.
The patch fixes some failures of the kvm unit tests apic and eventinj by
allowing to enable the proper CPU IRQ deassertion when the guest masks
some pending IRQs at PIC level.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Will be required when we no longer let i8259_init allocate the PIC IRQs
but convert that chips to qdev.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The ISA bus IRQ range is 0..15. What isa_irq_handler and IsaIrqState are
actually dealing with are the Global System Interrupts. Refactor the
code to clarify this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
IsaIrqState::ioapic is always non-NULL. Probably, the concrete
qemu_irq was supposed to be tested, but that's already done by
qemu_set_irq.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These boards carry similar hardware: SDRAM (48M for LX110, 64M for LX60,
96M for LX200), 16 Mbyte FLASH, FPGA, 10/100 Mbps Ethernet PHY and 16550
UART. FPGA may be loaded with almost any Tensilica processor. It is also
used to implement Ethernet MAC, e.g. OpenCores 10/100 Mbps Ethernet MAC
and LED/DIP switches access.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This is OpenCores Ethernet MAC + subset of National Semiconductors
DP83838C PHY.
OpenCores Ethernet MAC project: http://opencores.org/project,ethmac
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This is to get aligned with the linux name for this machine.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Xtensa cores may have different mapping of external interrupt pins to
internal IRQ numers. Implement API to acquire core IRQ by its external
interrupt number.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
QEMU timer is used to post CCOMPARE interrupt when the core is halted.
If that CCOMPARE interrupt is masked off then the timer must be rearmed
in the callback, otherwise it will be rearmed next time the core goes to
halt by the waiti instruction.
Add test case into timer testsuite.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This is conceptually cleaner and will allow us to drop the nographic
timer. Moreover, it will be mandatory to fully exploit future per-device
coalesced MMIO rings.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use file system driver specific lstat instead of generic lstat.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Removing the existing debug infrastrucure as proposed to be replaced by
Qemu Tracing infrastructure.
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Plan is to replace the existing debug infrastructure with Qemu tracing
infrastructure so that user can dynamically enable/disable trace events and
therefore a meaningful trace log can be generated which can be further
filtered using an analysis script.
Note: Because of current simpletrace limitations, the trace events are
logging at max 6 args, however, once the more args are supported, we can
change trace events to log more info as well. Also, This initial patch only
provides a replacement for existing debug infra. More trace events to be
added later for newly added handlers and sub-routines.
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This patch use file system specific ioctl for getting i_generation
value. Not all file system support the ioctl. So we add an export
specific extended operation and assign right callback for the
file system that support i_generation ioctl
["M. Mohan Kumar" <mohan@in.ibm.com> we can do ioctl only for
regular files and directories on the server]
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Some of the flags are OS/arch dependent we need to use
9P defined value on wire,
Based on the original patch from Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
If the 9pfs mount tag is longer than MAX_TAG_LEN bytes, rather than
silently truncating the tag which will likely break the guest OS,
report an immediate error and exit QEMU
* hw/9pfs/virtio-9p-device.c: Report error & exit if mount tag is
too long
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Use 9P specific lock constants instead of arch specific lock constants.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Also don't do glibc version check to find handle support. Instead
do handle syscall support in configure.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
interrput -> interrupt
Cc: Paul Brook <paul@codesourcery.com>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Calling usb_packet_complete() recursively when passing up the completion
event up the chain for devices connected via usb hub will trigger an
assert. So don't do that, make the usb hub emulation call the upstream
completion callback directly instead.
Based on a patch from Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
qemu uses the ps/2 mouse by default. The usb tablet (or mouse) is
activated as soon as qemu sees some guest activity on the device,
i.e. polling for HID events. That used to work fine for both fresh
boot and migration.
Remote wakeup support changed the picture though: There will be no
polling after migration in case the guest suspended the usb bus,
waiting for wakeup events. Result is that the ps/2 mouse stays
active.
Fix this by activating the usb tablet / mouse in post_load() in case
the guest enabled remote wakeup.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Honour the maximum packet size for endpoints; this applies when
sending non-isochronous data and means we transfer only as
much as the endpoint allows, leaving the transfer descriptor
on the list for another go next time around. This allows
usb-net to work when connected to an OHCI controller model.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The OHCI Transfer Descriptor T (DataToggle) bits are 24 and 25;
fix an error which accidentally overlaid them both on the same bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
commit 891fb2cd45 removed the implicit
detach before (re-)attaching in usb_attach(). Some usb host controllers
used that behavior though to do a port reset by a detach+attach
sequence.
This patch establishes old behavior by adding a new usb_reset() function
for port resets and putting it into use, thereby also unifying port
reset behavior of all host controllers. The patch also adds asserts to
usb_attach() and usb_detach() to make sure the calls are symmetrical.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When a usb packet is canceled we need to check whenever we actually have
a scsi request in flight before we try to cancel it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
writeout=immediate implies the after pwritev we do a sync_file_range.
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
All users have been converted to either isa_register_ioport
or isa_register_old_portio_list.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
[jan: fix cut'n'paste errors]
[avi: adjust pci variants not to use isa functions]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Paolo Bonzini