zicfiss introduces a new state ssp ("shadow stack register") in cpu.
ssp is expressed as a new unprivileged csr (CSR_SSP=0x11) and holds
virtual address for shadow stack as programmed by software.
Shadow stack (for each mode) is enabled via bit3 in *envcfg CSRs.
Shadow stack can be enabled for a mode only if it's higher privileged
mode had it enabled for itself. M mode doesn't need enabling control,
it's always available if extension is available on cpu.
This patch also implements helper bcfi function which determines if bcfi
is enabled at current privilege or not.
Adds ssp to migration state as well.
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-12-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
sw check exception support was recently added. This patch further augments
sw check exception by providing support for additional code which is
provided in *tval. Adds `sw_check_code` field in cpuarchstate. Whenever
sw check exception is raised *tval gets the value deposited in
`sw_check_code`.
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-6-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
zicfilp introduces a new state elp ("expected landing pad") in cpu.
During normal execution, elp is idle (NO_LP_EXPECTED) i.e not expecting
landing pad. On an indirect call, elp moves LP_EXPECTED. When elp is
LP_EXPECTED, only a subsquent landing pad instruction can set state back
to NO_LP_EXPECTED. On reset, elp is set to NO_LP_EXPECTED.
zicfilp is enabled via bit2 in *envcfg CSRs. Enabling control for M-mode
is in mseccfg CSR at bit position 10.
On trap, elp state is saved away in *status.
Adds elp to the migration state as well.
Signed-off-by: Deepak Gupta <debug@rivosinc.com>
Co-developed-by: Jim Shu <jim.shu@sifive.com>
Co-developed-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241008225010.1861630-4-debug@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The register VXSAT should be RW only to the first bit.
The remaining bits should be 0.
The RISC-V Instruction Set Manual Volume I: Unprivileged Architecture
The vxsat CSR has a single read-write least-significant bit (vxsat[0])
that indicates if a fixed-point instruction has had to saturate an output
value to fit into a destination format. Bits vxsat[XLEN-1:1]
should be written as zeros.
Signed-off-by: Evgenii Prokopiev <evgenii.prokopiev@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20241002084436.89347-1-evgenii.prokopiev@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Both CSRRS and CSRRC always read the addressed CSR and cause any read side
effects regardless of rs1 and rd fields. Note that if rs1 specifies a register
holding a zero value other than x0, the instruction will still attempt to write
the unmodified value back to the CSR and will cause any attendant side effects.
So if CSRRS or CSRRC tries to write a read-only CSR with rs1 which specifies
a register holding a zero value, an illegal instruction exception should be
raised.
Signed-off-by: Yu-Ming Chang <yumin686@andestech.com>
Signed-off-by: Alvin Chang <alvinga@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <172100444279.18077.6893072378718059541-0@git.sr.ht>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In case of programmable counters configured to count inst/cycles
we often end-up with counter not incrementing at all from kernel's
perspective.
For example:
- Kernel configures hpm3 to count instructions and sets hpmcounter
to -10000 and all modes except U mode are inhibited.
- In QEMU we configure a timer to expire after ~10000 instructions.
- Problem is, it's often the case that kernel might not even schedule
Umode task and we hit the timer callback in QEMU.
- In the timer callback we inject the interrupt into kernel, kernel
runs the handler and reads hpmcounter3 value.
- Given QEMU maintains individual counters to count for each privilege
mode, and given umode never ran, the umode counter didn't increment
and QEMU returns same value as was programmed by the kernel when
starting the counter.
- Kernel checks for overflow using previous and current value of the
counter and reprograms the counter given there wasn't an overflow
as per the counter value. (Which itself is a problem. We have QEMU
telling kernel that counter3 overflowed but the counter value
returned by QEMU doesn't seem to reflect that.).
This change makes sure that timer is reprogrammed from the handler
if the counter didn't overflow based on the counter value.
Second, this change makes sure that whenever the counter is read,
it's value is updated to reflect the latest count.
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240711-smcntrpmf_v7-v8-11-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently we start timer counter from write_mhpmcounter path only
without checking for mcountinhibit bit. This changes adds mcountinhibit
check and also programs the counter from write_mcountinhibit as well.
When a counter is stopped using mcountinhibit we simply update
the value of the counter based on current host ticks and save
it for future reads.
We don't need to disable running timer as pmu_timer_trigger_irq
will discard the interrupt if the counter has been inhibited.
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240711-smcntrpmf_v7-v8-10-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
scounteren/hcountern are also WARL registers similar to mcountern.
Only set the bits for the available counters during the write to
preserve the WARL behavior.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-9-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, if a counter monitoring cycle/instret is stopped via
mcountinhibit we just update the state while the value is saved
during the next read. This is not accurate as the read may happen
many cycles after the counter is stopped. Ideally, the read should
return the value saved when the counter is stopped.
Thus, save the value of the counter during the inhibit update
operation and return that value during the read if corresponding bit
in mcountihibit is set.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-8-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Privilege mode filtering can also be emulated for cycle/instret by
tracking host_ticks/icount during each privilege mode switch. This
patch implements that for both cycle/instret and mhpmcounters. The
first one requires Smcntrpmf while the other one requires Sscofpmf
to be enabled.
The cycle/instret are still computed using host ticks when icount
is not enabled. Otherwise, they are computed using raw icount which
is more accurate in icount mode.
Co-Developed-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-7-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, the INH fields are set in mhpmevent uncoditionally
without checking if a particular priv mode is supported or not.
Suggested-by: Alistair Francis <alistair23@gmail.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-6-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
QEMU only calculates dummy cycles and instructions, so there is no
actual means to stop the icount in QEMU. Hence this patch merely adds
the functionality of accessing the cfg registers, and cause no actual
effects on the counting of cycle and instret counters.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Kaiwen Xue <kaiwenx@rivosinc.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-5-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
mhpmeventhX CSRs are available for RV32. The predicate function
should check that first before checking sscofpmf extension.
Fixes: 1466448345 ("target/riscv: Add sscofpmf extension support")
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20240711-smcntrpmf_v7-v8-2-b7c38ae7b263@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Base on the riscv-privileged spec, vstvec substitutes for the usual stvec.
Therefore, the encoding of the MODE should also be restricted to 0 and 1.
Signed-off-by: Jiayi Li <lijiayi@eswincomputing.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-ID: <20240701022553.1982-1-lijiayi@eswincomputing.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When icount is enabled, rather than returning the virtual CPU time, we
should return the instruction count itself. Add an instructions bool
parameter to get_ticks() to correctly return icount_get_raw() when
icount_enabled() == 1 and instruction count is queried. This will modify
the existing behavior which was returning an instructions count close to
the number of cycles (CPI ~= 1).
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20240618112649.76683-1-cleger@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Based on privileged spec 1.13, the RV32 needs to implement MEDELEGH
and HEDELEGH for exception codes 32-47 for reserving and exception codes
48-63 for custom use. Add the CSR number though the implementation is
just reading zero and writing ignore. Besides, for accessing HEDELEGH, it
should be controlled by mstateen0 'P1P13' bit.
Signed-off-by: Fea.Wang <fea.wang@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240606135454.119186-5-fea.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Based on privilege 1.13 spec, there should be a bit56 for 'P1P13' in
mstateen0 that controls access to the hedeleg.
Signed-off-by: Fea.Wang <fea.wang@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Weiwei Li <liwei1518@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240606135454.119186-4-fea.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Qemu maps IRQs 0:15 for core interrupts and 16 onward for
guest interrupts which are later translated to hgiep in
`riscv_cpu_set_irq()` function.
With virtual IRQ support added, software now can fully
use the whole local interrupt range without any actual
hardware attached.
This change moves the guest interrupt range after the
core local interrupt range to avoid clash.
Fixes: 1697837ed9 ("target/riscv: Add M-mode virtual interrupt and IRQ filtering support.")
Fixes: 40336d5b1d ("target/riscv: Add HS-mode virtual interrupt and IRQ filtering support.")
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240520125157.311503-3-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
AIA extends the width of all IRQ CSRs to 64bit even
in 32bit systems by adding missing half CSRs.
This seems to be missed while adding support for
virtual IRQs. The whole logic seems to be correct
except the width of the masks.
Fixes: 1697837ed9 ("target/riscv: Add M-mode virtual interrupt and IRQ filtering support.")
Fixes: 40336d5b1d ("target/riscv: Add HS-mode virtual interrupt and IRQ filtering support.")
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240520125157.311503-2-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add support for Zve32x extension and replace some checks for Zve32f with
Zve32x, since Zve32f depends on Zve32x.
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Max Chou <max.chou@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240328022343.6871-2-jason.chien@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Zkr extension may only be exposed to KVM guests if the VMM
implements the SEED CSR. Use the same implementation as TCG.
Without this patch, running with a KVM which does not forward the
SEED CSR access to QEMU will result in an ILL exception being
injected into the guest (this results in Linux guests crashing on
boot). And, when running with a KVM which does forward the access,
QEMU will crash, since QEMU doesn't know what to do with the exit.
Fixes: 3108e2f1c6 ("target/riscv/kvm: update KVM exts to Linux 6.8")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Cc: qemu-stable <qemu-stable@nongnu.org>
Message-ID: <20240422134605.534207-2-ajones@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Added xATP_MODE validation for vsatp/hgatp CSRs.
The xATP register is an SXLEN-bit read/write WARL register, so
the legal value must be returned (See riscv-privileged-20211203, SATP/VSATP/HGATP CSRs).
Signed-off-by: Irina Ryapolova <irina.ryapolova@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240109145923.37893-2-irina.ryapolova@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The SATP register is an SXLEN-bit read/write WARL register. It means that CSR fields are only defined
for a subset of bit encodings, but allow any value to be written while guaranteeing to return a legal
value whenever read (See riscv-privileged-20211203, SATP CSR).
For example on rv64 we are trying to write to SATP CSR val = 0x1000000000000000 (SATP_MODE = 1 - Reserved for standard use)
and after that we are trying to read SATP_CSR. We read from the SATP CSR value = 0x1000000000000000, which is not a correct
operation (return illegal value).
Signed-off-by: Irina Ryapolova <irina.ryapolova@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240109145923.37893-1-irina.ryapolova@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The hypervisor should decide what it wants to enable. Zero all
configuration enable bits on reset.
Also, commit ed67d63798 ("target/riscv: Update CSR bits name for
svadu extension") missed one reference to 'hade'. Change it now.
Fixes: 0af3f115e6 ("target/riscv: Add *envcfg.HADE related check in address translation")
Fixes: ed67d63798 ("target/riscv: Update CSR bits name for svadu extension")
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240215223955.969568-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The real return value type has been converted to RISCVException,
but some function declarations still not. This patch makes all
csr operation declarations use RISCVExcetion.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240130110844.437-1-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
As a bonus, we're being more idiomatic using cpu->cfg.vlenb when
reading CSR_VLENB.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122161107.26737-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The debug Sdtrig extension defines an CSR "mcontext". This commit
implements its predicate and read/write operations into CSR table.
Its value is reset as 0 when the trigger module is reset.
Signed-off-by: Alvin Chang <alvinga@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231219123244.290935-1-alvinga@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The CSRs will always be between either CSR_MHPMCOUNTER3 and
CSR_MHPMCOUNTER31 or CSR_MHPMCOUNTER3H and CSR_MHPMCOUNTER31H.
So although ctr_index can't be negative, Coverity doesn't know this and
it isn't obvious to human readers either. Let's add an assert to ensure
that Coverity knows the values will be within range.
To simplify the code let's also change the RV32 adjustment.
Fixes: Coverity CID 1523910
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240108001328.280222-2-alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If CPU does not implement the Vector extension, it usually means
mstatus vs hardwire to zero. So we should not allow write a
non-zero value to this field.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231215023313.1708-1-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The mcycle/minstret counter's stop flag is mistakenly updated on a copy
on stack. Thus the counter increments even when the CY/IR bit in the
mcountinhibit register is set. This commit corrects its behavior.
Fixes: 3780e33732 (target/riscv: Support mcycle/minstret write operation)
Signed-off-by: Xu Lu <luxu.kernel@bytedance.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Check the PMU available bitmask when checking if a counter is valid
rather than comparing the index against the number of PMUs.
Signed-off-by: Rob Bradford <rbradford@rivosinc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20231031154000.18134-3-rbradford@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The CSR register mseccfg is used by multiple extensions: Smepm and Zkr.
Consider this when checking the existence of the register.
Fixes: 77442380ec ("target/riscv: rvk: add CSR support for Zkr")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231030102105.19501-1-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
zicntr is the Base Counters and Timers extension described in chapter 12
of the unprivileged spec. It describes support for RDCYCLE, RDTIME and
RDINSTRET.
QEMU already implements it in TCG way before it was a discrete
extension. zicntr is part of the RVA22 profile, so let's add it to QEMU
to make the future profile implementation flag complete. Given than it
represents an already existing feature, default it to 'true' for all
CPUs.
For TCG, we need a way to disable zicntr if the user wants to. This is
done by restricting access to the CYCLE, TIME, and INSTRET counters via
the 'ctr()' predicate when we're about to access them.
Disabling zicntr happens via the command line or if its dependency,
zicsr, happens to be disabled. We'll check for zicsr during realize()
and, in case it's absent, disable zicntr. However, if the user was
explicit about having zicntr support, error out instead of disabling it.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231023153927.435083-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Smepmp is a ratified extension which qemu refers to as epmp.
Rename epmp to smepmp and add it to extension list so that
it is added to the isa string.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231019065546.1431579-1-mchitale@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change adds support for inserting virtual interrupts from HS-mode
into VS-mode using hvien and hvip csrs. This also allows for IRQ filtering
from HS-mode.
Also, the spec doesn't mandate the interrupt to be actually supported
in hardware. Which allows HS-mode to assert virtual interrupts to VS-mode
that have no connection to any real interrupt events.
This is defined as part of the AIA specification [0], "6.3.2 Virtual
interrupts for VS level".
[0]: https://github.com/riscv/riscv-aia/releases/download/1.0/riscv-interrupts-1.0.pdf
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231016111736.28721-7-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change adds support for inserting virtual interrupts from M-mode
into S-mode using mvien and mvip csrs. IRQ filtering is a use case of
this change, i-e M-mode can stop delegating an interrupt to S-mode and
instead enable it in MIE and receive those interrupts in M-mode and then
selectively inject the interrupt using mvien and mvip.
Also, the spec doesn't mandate the interrupt to be actually supported
in hardware. Which allows M-mode to assert virtual interrupts to S-mode
that have no connection to any real interrupt events.
This is defined as part of the AIA specification [0], "5.3 Interrupt
filtering and virtual interrupts for supervisor level".
[0]: https://github.com/riscv/riscv-aia/releases/download/1.0/riscv-interrupts-1.0.pdf
Signed-off-by: Rajnesh Kanwal <rkanwal@rivosinc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231016111736.28721-6-rkanwal@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a leading 'z' to improve grepping. When one wants to search for uses
of zicsr they're more likely to do 'grep -i zicsr' than 'grep -i icsr'.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20231012164604.398496-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This function is the core of the RISC-V validations for TCG CPUs, and it
has a lot going on.
Functions in cpu.c were made public to allow them to be used by the KVM
accelerator class later on. 'cpu_cfg_ext_get_min_version()' is notably
hard to move it to another file due to its dependency with isa_edata_arr[]
array, thus make it public and use it as is for now.
riscv_cpu_validate_set_extensions() is kept public because it's used by
csr.c in write_misa().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230925175709.35696-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
As per ISA:
"For CSRRWI, if rd=x0, then the instruction shall not read the CSR and
shall not cause any of the side effects that might occur on a CSR read."
trans_csrrwi() and trans_csrrw() call do_csrw() if rd=x0, do_csrw() calls
riscv_csrrw_do64(), via helper_csrw() passing NULL as *ret_value.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230808090914.17634-1-nikita.shubin@maquefel.me>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
According to the new spec, when vsiselect has a reserved value, attempts
from M-mode or HS-mode to access vsireg, or from VS-mode to access
sireg, should preferably raise an illegal instruction exception.
Signed-off-by: Tommy Wu <tommy.wu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-ID: <20230816061647.600672-1-tommy.wu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Svadu specification updated the name of the *envcfg bit from
HADE to ADUE.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230816141916.66898-1-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
These are WARL fields - zero out the bits for unavailable counters and
special case the TM bit in mcountinhibit which is hardwired to zero.
This patch achieves this by modifying the value written so that any use
of the field will see the correctly masked bits.
Tested by modifying OpenSBI to write max value to these CSRs and upon
subsequent read the appropriate number of bits for number of PMUs is
enabled and the TM bit is zero in mcountinhibit.
Signed-off-by: Rob Bradford <rbradford@rivosinc.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Message-ID: <20230802124906.24197-1-rbradford@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
"qemu/main-loop.h" declares functions related to QEMU's
main loop mutex, which these files don't access. Remove
the unused "qemu/main-loop.h" header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-8-philmd@linaro.org>
Pointer mask is also affected by MPRV which means cur_pmbase/pmmask
should also take MPRV into consideration. As pointer mask for instruction
is not supported currently, so we can directly update cur_pmbase/pmmask
based on address related mode and xlen affected by MPRV now.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230614032547.35895-3-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SXL is initialized as env->misa_mxl which is also the mxl value.
So we can just remain it unchanged to keep it read-only.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230603134236.15719-4-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
MPV and GVA bits are added by hypervisor extension to mstatus
and mstatush (if MXLEN=32).
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230603134236.15719-3-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Implement the s/h/mstateen.fcsr bit as defined in the smstateen spec
and check for it when accessing the fcsr register and its fields.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230518175058.2772506-2-mchitale@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
write_mstatus() can only change current xl when in debug mode.
And we need update cur_pmmask/base in this case.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-Id: <20230524015933.17349-3-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Deepak Gupta