POWER9 DD2.1 and earlier had significant limitations when running KVM,
including lack of "mixed mode" MMU support (ability to run HPT and RPT
mode on threads of the same core), and a translation prefetch issue
which is worked around by disabling "AIL" mode for the guest.
These processors are not widely available, and it's difficult to deal
with all these quirks in qemu +/- KVM, so create a POWER9 DD2.2 CPU
and make it the default POWER9 CPU.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Message-Id: <20230515160201.394587-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
As lpc-hc is designed for re-entrant calls from xscom, mark it
re-entrancy safe.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
[clg: mark opb_master_regs as re-entrancy safe also ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230526073850.2772197-1-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Commit cef2e7148e ("hw/isa/i82378: Remove intermediate IRQ forwarder")
passes s->cpu_intr to i8259_init() in i82378_realize() directly. However, s-
>cpu_intr isn't initialized yet since that happens after the south bridge's
pci_realize_and_unref() in board code. Fix this by initializing s->cpu_intr
before realizing the south bridge.
Fixes: cef2e7148e ("hw/isa/i82378: Remove intermediate IRQ forwarder")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230304114043.121024-4-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The behaviour of the Address Translation Mode on Interrupt resource is
not consistently supported by all CPU versions or all KVM versions: KVM
HV does not support mode 2, and does not support mode 3 on POWER7 or
early POWER9 processesors. KVM PR only supports mode 0. TCG supports all
modes (0, 2, 3) on CPUs with support for the corresonding LPCR[AIL] mode.
This leads to inconsistencies in guest behaviour and could cause problems
migrating guests.
This was not noticable for Linux guests for a long time because the
kernel only uses modes 0 and 3, and it used to consider AIL-3 to be
advisory in that it would always keep the AIL-0 vectors around, so it
did not matter whether or not interrupts were delivered according to
the AIL mode. Recent Linux guests depend on AIL mode 3 working as
specified in order to support the SCV facility interrupt. If AIL-3 can
not be provided, then H_SET_MODE must return an error to Linux so it can
disable the SCV facility (failure to do so can lead to userspace being
able to crash the guest kernel).
Add the ail-mode-3 capability to specify that AIL-3 is supported. AIL-0
is implied as the baseline, and AIL-2 is no longer supported by spapr.
AIL-2 is not known to be used by any software, but support in TCG could
be restored with an ail-mode-2 capability quite easily if a regression
is reported.
Modify the H_SET_MODE Address Translation Mode on Interrupt resource
handler to check capabilities and correctly return error if not
supported.
KVM has a cap to advertise support for AIL-3.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230515160216.394612-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add virtio-multitouch-pci, a Multitouch-capable input device, to the
list of devices that can be provided by virtio-input-pci.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230526112925.38794-5-slp@redhat.com>
Add a virtio-multitouch device to the family of devices emulated by
virtio-input implementing the Multi-touch protocol as descripted here:
https://www.kernel.org/doc/html/latest/input/multi-touch-protocol.html?highlight=multi+touch
This patch just add the device itself, without connecting it to any
backends. The following patches will add a PCI-based multitouch device,
some helpers in "ui" and will enable the GTK3 backend to transpose
multi-touch events from the host to the guest.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230526112925.38794-4-slp@redhat.com>
As there are other bitmap-based config properties that need to be dealt in a
similar fashion as VIRTIO_INPUT_CFG_EV_BITS, generalize the function to
receive select and subsel as arguments, and rename it to
virtio_input_extend_config()
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230526112925.38794-2-slp@redhat.com>
It looks like the virtio_gpu_load() does not compute and set the offset,
the same way virtio_gpu_set_scanout() does. This probably results in
incorrect display until the scanout/framebuffer is updated again, I
guess we should fix it, although I haven't checked this yet.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230515132518.1025853-1-marcandre.lureau@redhat.com>
The VirtioInfoList is already allocated by QAPI_LIST_PREPEND and
need not be allocated by the caller.
Fixes Coverity CID 1508724.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We cannot use the generic reentrancy guard in the LSI code, so
we have to manually prevent endless reentrancy here. The problematic
lsi_execute_script() function has already a way to detect whether
too many instructions have been executed - we just have to slightly
change the logic here that it also takes into account if the function
has been called too often in a reentrant way.
The code in fuzz-lsi53c895a-test.c has been taken from an earlier
patch by Mauro Matteo Cascella.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1563
Message-Id: <20230522091011.1082574-1-thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
While trying to use a SCSI disk on the LSI controller with an
older version of Fedora (25), I'm getting:
qemu: warning: Blocked re-entrant IO on MemoryRegion: lsi-mmio at addr: 0x34
and the SCSI controller is not usable. Seems like we have to
disable the reentrancy checker for the MMIO region, too, to
get this working again.
The problem could be reproduced it like this:
./qemu-system-x86_64 -accel kvm -m 2G -machine q35 \
-device lsi53c810,id=lsi1 -device scsi-hd,drive=d0 \
-drive if=none,id=d0,file=.../somedisk.qcow2 \
-cdrom Fedora-Everything-netinst-i386-25-1.3.iso
Where somedisk.qcow2 is an image that contains already some partitions
and file systems.
In the boot menu of Fedora, go to
"Troubleshooting" -> "Rescue a Fedora system" -> "3) Skip to shell"
Then check "dmesg | grep -i 53c" for failure messages, and try to mount
a partition from somedisk.qcow2.
Message-Id: <20230516090556.553813-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
QEMU aborts when default RAM backend should be used (i.e. no
explicit '-machine memory-backend=' specified) but user
has created an object which 'id' equals to default RAM backend
name used by board.
$QEMU -machine pc \
-object memory-backend-ram,id=pc.ram,size=4294967296
Actual results:
QEMU 7.2.0 monitor - type 'help' for more information
(qemu) Unexpected error in object_property_try_add() at ../qom/object.c:1239:
qemu-kvm: attempt to add duplicate property 'pc.ram' to object (type 'container')
Aborted (core dumped)
Instead of abort, check for the conflicting 'id' and exit with
an error, suggesting how to remedy the issue.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2207886
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230522131717.3780533-1-imammedo@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230524122559.28863-1-philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230524082037.1620952-1-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230523110435.1375774-6-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230523110435.1375774-5-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Tested-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230523110435.1375774-4-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230523110435.1375774-3-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230523110435.1375774-2-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
* purge qatomic_mb_read/set from monitor
* build system fixes
* OHCI fix from gitlab
* provide EPYC-Rome CPU model not susceptible to XSAVES erratum
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmRvGpEUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOa/Af/WS5/tmIlEYgH7UOPERQXNqf7+Jwj
bA2wgqv3ZoQwcgp5f4EVjfA8ABfpGxLZy6xIdUSbWANb8lDJNuh/nPd/em3rWUAU
LnJGGdo1vF31gfsVQnlzb7hJi3ur+e2f8JqkRVskDCk3a7YY44OCN42JdKWLrN9u
CFf2zYqxMqXHjrYrY0Kx2oTkfGDZrfwUlx0vM4dHb8IEoxaplfDd8lJXQzjO4htr
3nPBPjQ+h08EeC7mObH4XoJE0omzovR10GkBo8K4q952xGOQ041Y/2YY7JwLfx0D
na7IanVo+ZAmvTJZoJFSBwNnXkTMHvDH5+Hc45NSTsDBtz0YJhRxPw/z/A==
=A5Lp
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* hot-unplug fixes for ioport
* purge qatomic_mb_read/set from monitor
* build system fixes
* OHCI fix from gitlab
* provide EPYC-Rome CPU model not susceptible to XSAVES erratum
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmRvGpEUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroOa/Af/WS5/tmIlEYgH7UOPERQXNqf7+Jwj
# bA2wgqv3ZoQwcgp5f4EVjfA8ABfpGxLZy6xIdUSbWANb8lDJNuh/nPd/em3rWUAU
# LnJGGdo1vF31gfsVQnlzb7hJi3ur+e2f8JqkRVskDCk3a7YY44OCN42JdKWLrN9u
# CFf2zYqxMqXHjrYrY0Kx2oTkfGDZrfwUlx0vM4dHb8IEoxaplfDd8lJXQzjO4htr
# 3nPBPjQ+h08EeC7mObH4XoJE0omzovR10GkBo8K4q952xGOQ041Y/2YY7JwLfx0D
# na7IanVo+ZAmvTJZoJFSBwNnXkTMHvDH5+Hc45NSTsDBtz0YJhRxPw/z/A==
# =A5Lp
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 25 May 2023 01:21:37 AM PDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [undefined]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
monitor: do not use mb_read/mb_set
monitor: extract request dequeuing to a new function
monitor: introduce qmp_dispatcher_co_wake
monitor: cleanup fetching of QMP requests
monitor: cleanup detection of qmp_dispatcher_co shutting down
monitor: do not use mb_read/mb_set for suspend_cnt
monitor: add more *_locked() functions
monitor: allow calling monitor_resume under mon_lock
monitor: use QEMU_LOCK_GUARD a bit more
softmmu/ioport.c: make MemoryRegionPortioList owner of portio_list MemoryRegions
softmmu/ioport.c: QOMify MemoryRegionPortioList
softmmu/ioport.c: allocate MemoryRegionPortioList ports on the heap
usb/ohci: Set pad to 0 after frame update
meson: move -no-pie from linker to compiler
meson: fix rule for qemu-ga installer
meson.build: Fix glib -Wno-unused-function workaround
target/i386: EPYC-Rome model without XSAVES
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When the OHCI controller's framenumber is incremented, HccaPad1 register
should be set to zero (Ref OHCI Spec 4.4)
ReactOS uses hccaPad1 to determine if the OHCI hardware is running,
consequently it fails this check in current qemu master.
Signed-off-by: Ryan Wendland <wendland@live.com.au>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1048
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vbasedev->name is freed wrongly which leads to garbage VFIO trace log.
Fix it by allocating a dup of vbasedev->name and then free the dup.
Fixes: 2dca1b37a7 ("vfio/pci: add support for VF token")
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Add an option for hostmem-file to start the memory object at an offset
into the target file. This is useful if multiple memory objects reside
inside the same target file, such as a device node.
In particular, it's useful to map guest memory directly into /dev/mem
for experimentation.
To make this work consistently, also fix up all places in QEMU that
expect fd offsets to be 0.
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20230403221421.60877-1-graf@amazon.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
vmxnet3 has no dependency on PC, and VMware Fusion actually makes it
available on Apple Silicon according to:
https://kb.vmware.com/s/article/90364
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
For GPIE.NSICR, Section 7.3.2.1.2 says:
> ICR bits are cleared on register read. If GPIE.NSICR = 0b, then the
> clear on read occurs only if no bit is set in the IMS or at least one
> bit is set in the IMS and there is a true interrupt as reflected in
> ICR.INTA.
e1000e does similar though it checks for CTRL_EXT.IAME, which does not
exist on igb.
Suggested-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This follows the corresponding change for e1000e. This fixes:
tests/avocado/netdev-ethtool.py:NetDevEthtool.test_igb
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In MSI-X mode, if there are interrupts already notified but not cleared
and a new interrupt arrives, e1000e incorrectly notifies the notified
ones again along with the new one.
To fix this issue, replace e1000e_update_interrupt_state() with
two new functions: e1000e_raise_interrupts() and
e1000e_lower_interrupts(). These functions don't only raise or lower
interrupts, but it also performs register writes which updates the
interrupt state. Before it performs a register write, these function
determines the interrupts already raised, and compares with the
interrupts raised after the register write to determine the interrupts
to notify.
The introduction of these functions made tracepoints which assumes that
the caller of e1000e_update_interrupt_state() performs register writes
obsolete. These tracepoints are now removed, and alternative ones are
added to the new functions.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb has a configurable size limit for LPE, and uses different limits
depending on whether the packet is treated as a VLAN packet.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e does not support using UDP for RSS hash, but igb does.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
eth_strip_vlan and eth_strip_vlan_ex refers to ehdr_buf as struct
eth_header. Enforce alignment for the structure.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
It is possible to have another VLAN tag even if the packet is already
tagged.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Rename variable "n" to "causes", which properly represents the content
of the variable.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Rename variable "n" to "causes", which properly represents the content
of the variable.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 7.3.4.1 says:
> When auto-clear is enabled for an interrupt cause, the EICR bit is
> set when a cause event mapped to this vector occurs. When the EITR
> Counter reaches zero, the MSI-X message is sent on PCIe. Then the
> EICR bit is cleared and enabled to be set by a new cause event
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The constants need to be consistent between the PF and VF.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Keeping Tx packet state after the transmit queue is emptied but this
behavior is unreliable as the state can be reset anytime the migration
happens.
Always reset Tx packet state always after the queue is emptied.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Keeping Tx packet state after the transmit queue is emptied has some
problems:
- The datasheet says the descriptors can be reused after the transmit
queue is emptied, but the Tx packet state may keep references to them.
- The Tx packet state cannot be migrated so it can be reset anytime the
migration happens.
Always reset Tx packet state always after the queue is emptied.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 7.2.2.3 Advanced Transmit Data Descriptor says:
> For frames that spans multiple descriptors, all fields apart from
> DCMD.EOP, DCMD.RS, DCMD.DEXT, DTALEN, Address and DTYP are valid only
> in the first descriptors and are ignored in the subsequent ones.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The goto is a bit confusing as it changes the control flow only if L4
protocol is not recognized. It is also different from e1000e, and
noisy when comparing e1000e and igb.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Without this change, the status flags may not be traced e.g. if checksum
offloading is disabled.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Without this change, the status flags may not be traced e.g. if checksum
offloading is disabled.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e and igb employs NetPktRssIpV6TcpEx for RSS hash if TcpIpv6 MRQC
bit is set. Moreover, igb also has a MRQC bit for NetPktRssIpV6Tcp
though it is not implemented yet. Rename it to TcpIpv6Ex to avoid
confusion.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 13.7.15 Receive Length Error Count says:
> Packets over 1522 bytes are oversized if LongPacketEnable is 0b
> (RCTL.LPE). If LongPacketEnable (LPE) is 1b, then an incoming packet
> is considered oversized if it exceeds 16384 bytes.
> These lengths are based on bytes in the received packet from
> <Destination Address> through <CRC>, inclusively.
As QEMU processes packets without CRC, the number of bytes for CRC
need to be subtracted. This change adds some size definitions to be used
to derive the new size thresholds to eth.h.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This saves some code and enables tracepoint for e1000's VLAN filtering.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The old eth_setup_vlan_headers has no user so remove it and rename
eth_setup_vlan_headers_ex.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb_receive_internal() used to check the iov length to determine
copy the iovs to a contiguous buffer, but the check is flawed in two
ways:
- It does not ensure that iovcnt > 0.
- It does not take virtio-net header into consideration.
The size of this copy is just 22 octets, which can be even less than
the code size required for checks. This (wrong) optimization is probably
not worth so just remove it. Removing this also allows igb to assume
aligned accesses for the ethernet header.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e_receive_internal() used to check the iov length to determine
copy the iovs to a contiguous buffer, but the check is flawed in two
ways:
- It does not ensure that iovcnt > 0.
- It does not take virtio-net header into consideration.
The size of this copy is just 18 octets, which can be even less than
the code size required for checks. This (wrong) optimization is probably
not worth so just remove it.
Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb does not properly ensure the buffer passed to
net_rx_pkt_set_protocols() is contiguous for the entire L2/L3/L4 header.
Allow it to pass scattered data to net_rx_pkt_set_protocols().
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The datasheet says contradicting statements regarding ICR accesses so it
is not reliable to determine the behavior of ICR accesses. However,
e1000e does clear IMS bits when reading ICR accesses and Linux also
expects ICR accesses will clear IMS bits according to:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/intel/igb/igb_main.c?h=v6.2#n8048
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
While the datasheet of e1000e says it checks CTRL.VME for tx VLAN
tagging, igb's datasheet has no such statements. It also says for
"CTRL.VLE":
> This register only affects the VLAN Strip in Rx it does not have any
> influence in the Tx path in the 82576.
(Appendix A. Changes from the 82575)
There is no "CTRL.VLE" so it is more likely that it is a mistake of
CTRL.VME.
Fixes: fba7c3b788 ("igb: respect VMVIR and VMOLR for VLAN")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb's advanced descriptor uses a packet type encoding different from
one used in e1000e's extended descriptor. Fix the logic to encode
Rx packet type accordingly.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Before this change, e1000 and the common code updated BPRC and MPRC
depending on the matched filter, but e1000e and igb decided to update
those counters by deriving the packet type independently. This
inconsistency caused a multicast packet to be counted twice.
Updating BPRC and MPRC depending on are fundamentally flawed anyway as
a filter can be used for different types of packets. For example, it is
possible to filter broadcast packets with MTA.
Always determine what counters to update by inspecting the packets.
Fixes: 3b27430177 ("e1000: Implementing various counters")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This allows to use the network packet abstractions even if PCI is not
used.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is intended to be followed by another change for the interface.
It also fixes the leak of memory mapping when the specified memory is
partially mapped.
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The bytes and packets counter registers are cleared on read.
Copying the "total counter" registers to the "good counter" registers has
side effects.
If the "total" register is never read by the OS, it only gets incremented.
This leads to exponential growth of the "good" register.
This commit increments the counters individually to avoid this.
Signed-off-by: Timothée Cocault <timothee.cocault@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Announce the default NIC via MachineClass->default_nic and set up
MachineClass->no_parallel according to the availability of the
"isa-parallel" device, so that the Sun machines also work when
QEMU has been configured with "--without-default-devices".
Message-Id: <20230512124033.502654-11-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Don't try to instantiate the parallel port if it has not been
enabled in the build configuration.
Message-Id: <20230512124033.502654-10-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are going to require the macro from other files, too, so move
this #define to the header file.
Message-Id: <20230512124033.502654-9-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230512124033.502654-8-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230512124033.502654-7-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230512124033.502654-6-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are going to re-use this setting for other targets, so let's
move this to the main MachineClass.
Message-Id: <20230512124033.502654-4-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "isapc" machine can also be run without VGA card, so there
is no need for a hard requirement with a "select" here - "imply"
is enough.
Message-Id: <20230512124033.502654-2-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
CXL volatile memory support
More memslots for vhost-user on x86 and ARM.
vIOMMU support for vhost-vdpa
pcie-to-pci bridge can now be compiled out
MADT revision bumped to 3
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmRniWoPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpN4MH/RqdvHmujrjvjzXbbN/gq87Njp+kQLKEooIE
ZkqdNaVUE6vjCH8iU+chjsxt4VSquSjOL9CWWrYefEIeqCFLWsuXSAY0VDAbY67x
+aes51tTYILVsx7fbb+T5mJKRgVuWW4C5KaGeQ1djSexy42nvplZUJdIJUhZr0t9
dzzOsD+mezHS7Xu2QOzSfl5QQRuOVVJnjJXkqJG/yRvHrZM5aTolatr/X7jNGedm
4oyMsVMaAcQ+dnEQigRJodf/MpFfs9DfNZAH55VwwQWsNT0t0ueD0xigR203jjaE
mJJJipAqetFax2JjC7QMXWf+LR36BnL/0/xH+x/BWb0FI42wr0I=
=ajmR
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: fixes, features, cleanups
CXL volatile memory support
More memslots for vhost-user on x86 and ARM.
vIOMMU support for vhost-vdpa
pcie-to-pci bridge can now be compiled out
MADT revision bumped to 3
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmRniWoPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpN4MH/RqdvHmujrjvjzXbbN/gq87Njp+kQLKEooIE
# ZkqdNaVUE6vjCH8iU+chjsxt4VSquSjOL9CWWrYefEIeqCFLWsuXSAY0VDAbY67x
# +aes51tTYILVsx7fbb+T5mJKRgVuWW4C5KaGeQ1djSexy42nvplZUJdIJUhZr0t9
# dzzOsD+mezHS7Xu2QOzSfl5QQRuOVVJnjJXkqJG/yRvHrZM5aTolatr/X7jNGedm
# 4oyMsVMaAcQ+dnEQigRJodf/MpFfs9DfNZAH55VwwQWsNT0t0ueD0xigR203jjaE
# mJJJipAqetFax2JjC7QMXWf+LR36BnL/0/xH+x/BWb0FI42wr0I=
# =ajmR
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 19 May 2023 07:36:26 AM PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (40 commits)
hw/i386/pc: No need for rtc_state to be an out-parameter
hw/i386/pc: Create RTC controllers in south bridges
hw/cxl: Introduce cxl_device_get_timestamp() utility function
hw/cxl: rename mailbox return code type from ret_code to CXLRetCode
hw/pci-bridge: make building pcie-to-pci bridge configurable
virtio-pci: add handling of PCI ATS and Device-TLB enable/disable
hw/pci-host/pam: Make init_pam() usage more readable
hw/i386/pc: Initialize ram_memory variable directly
hw/i386/pc_{q35,piix}: Minimize usage of get_system_memory()
hw/i386/pc_{q35,piix}: Reuse MachineClass::desc as SMB product name
hw/i386/pc_q35: Reuse machine parameter
hw/pci-host/q35: Inline sysbus_add_io()
hw/pci-host/i440fx: Inline sysbus_add_io()
vhost-vdpa: Add support for vIOMMU.
vhost-vdpa: Add check for full 64-bit in region delete
vhost_vdpa: fix the input in trace_vhost_vdpa_listener_region_del()
vhost: expose function vhost_dev_has_iommu()
virtio-crypto: fix NULL pointer dereference in virtio_crypto_free_request
virtio-net: not enable vq reset feature unconditionally
vhost-user: Remove acpi-specific memslot limit
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This reverts commit b320e21c48,
which accidentally broke TCG, because it made the TCG -cpu max
report the presence of MTE to the guest even if the board hadn't
enabled MTE by wiring up the tag RAM. This meant that if the guest
then tried to use MTE QEMU would segfault accessing the
non-existent tag RAM:
==346473==ERROR: UndefinedBehaviorSanitizer: SEGV on unknown address (pc 0x55f328952a4a bp 0x00000213a400 sp 0x7f7871859b80 T346476)
==346473==The signal is caused by a READ memory access.
==346473==Hint: this fault was caused by a dereference of a high value address (see register values below). Disassemble the provided pc to learn which register was used.
#0 0x55f328952a4a in address_space_to_flatview /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/include/exec/memory.h:1108:12
#1 0x55f328952a4a in address_space_translate /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/include/exec/memory.h:2797:31
#2 0x55f328952a4a in allocation_tag_mem /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/arm-clang/../../target/arm/tcg/mte_helper.c:176:10
#3 0x55f32895366c in helper_stgm /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/arm-clang/../../target/arm/tcg/mte_helper.c:461:15
#4 0x7f782431a293 (<unknown module>)
It's also not clear that the KVM logic is correct either:
MTE defaults to on there, rather than being only on if the
board wants it on.
Revert the whole commit for now so we can sort out the issues.
(We didn't catch this in CI because we have no test cases in
avocado that use guests with MTE support.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230519145808.348701-1-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that the RTC is created as part of the southbridges it doesn't need
to be an out-parameter any longer.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230519084734.220480-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Just like in the real hardware (and in PIIX4), create the RTC
controllers in the south bridges.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230519084734.220480-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are new users of this functionality coming shortly so factor
it out from the GET_TIMESTAMP mailbox command handling.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230423162013.4535-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Given the increasing usage of this mailbox return code type, now
is a good time to switch to QEMU style naming.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230423162013.4535-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a CONFIG option to build the pcie-to-pci bridge. No
functional change since it's enabled per default for PCIE_PORT=y.
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Message-Id: <72b6599d-6b27-00b5-aac5-2ebc16a2e023@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to PCIe Address Translation Services specification 5.1.3.,
ATS Control Register has Enable bit to enable/disable ATS. Guest may
enable/disable PCI ATS and, accordingly, Device-TLB for the VirtIO PCI
device. So, raise/lower a flag and call a trigger function to pass this
event to a device implementation.
Signed-off-by: Viktor Prutyanov <viktor@daynix.com>
Message-Id: <20230512135122.70403-2-viktor@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Unlike pam_update() which takes the subject -- PAMMemoryRegion -- as
first argument, init_pam() takes it as fifth (!) argument. This makes it
quite hard to figure out what an init_pam() invocation actually
initializes. By moving the subject to the front this should become
clearer.
While at it, lower the DeviceState parameter to Object, also
communicating more clearly that this parameter is just the owner rather
than some (heavy?) dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213162004.2797-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Going through pc_memory_init() seems quite complicated for a simple
assignment.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213162004.2797-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230213162004.2797-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
No need to repeat the descriptions.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230213162004.2797-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230213162004.2797-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
sysbus_add_io() just wraps memory_region_add_subregion() while also
obscuring where the memory is attached. So use
memory_region_add_subregion() directly and attach it to the existing
memory region s->mch.address_space_io which is set as an alias to
get_system_io() by the q35 machine.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230213162004.2797-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
sysbus_add_io() just wraps memory_region_add_subregion() while also
obscuring where the memory is attached. So use
memory_region_add_subregion() directly and attach it to the existing
memory region s->bus->address_space_io which is set as an alias to
get_system_io() by the pc machine.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230213162004.2797-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
1. The vIOMMU support will make vDPA can work in IOMMU mode. This
will fix security issues while using the no-IOMMU mode.
To support this feature we need to add new functions for IOMMU MR adds and
deletes.
Also since the SVQ does not support vIOMMU yet, add the check for IOMMU
in vhost_vdpa_dev_start, if the SVQ and IOMMU enable at the same time
the function will return fail.
2. Skip the iova_max check vhost_vdpa_listener_skipped_section(). While
MR is IOMMU, move this check to vhost_vdpa_iommu_map_notify()
Verified in vp_vdpa and vdpa_sim_net driver
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20230510054631.2951812-5-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The unmap ioctl doesn't accept a full 64-bit span. So need to
add check for the section's size in vhost_vdpa_listener_region_del().
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20230510054631.2951812-4-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In trace_vhost_vdpa_listener_region_del, the value for llend
should change to int128_get64(int128_sub(llend, int128_one()))
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20230510054631.2951812-3-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support vIOMMU in vdpa, need to exposed the function
vhost_dev_has_iommu, vdpa will use this function to check
if vIOMMU enable.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20230510054631.2951812-2-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Ensure op_info is not NULL in case of QCRYPTODEV_BACKEND_ALG_SYM algtype.
Fixes: 0e660a6f90 ("crypto: Introduce RSA algorithm")
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reported-by: Yiming Tao <taoym@zju.edu.cn>
Message-Id: <20230509075317.1132301-1-mcascell@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: zhenwei pi<pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The commit 93a97dc520 ("virtio-net: enable vq reset feature") enables
unconditionally vq reset feature as long as the device is emulated.
This makes impossible to actually disable the feature, and it causes
migration problems from qemu version previous than 7.2.
The entire final commit is unneeded as device system already enable or
disable the feature properly.
This reverts commit 93a97dc520.
Fixes: 93a97dc520 ("virtio-net: enable vq reset feature")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230504101447.389398-1-eperezma@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's just support 512 memslots on x86-64 and aarch64 as well. The maximum
number of ACPI slots (256) is no longer completely expressive ever since
we supported virtio-based memory devices. Further, we're completely
ignoring other memslots used outside of memory device context, such as
memslots used for boot memory.
Note that the vhost memslot limit in the kernel is usually configured to
be 509. With this change, we prepare vhost-user on the QEMU side to be
closer to that limit, to eventually support ~512 memslots in most vhost
implementations and have less "surprises" when cold/hotplugging vhost
devices while also consuming more memslots than we're currently used to
by memory devices (e.g., once virtio-mem starts using multiple memslots).
Note that most vhost-user implementations only support a small number of
memslots so far, which we can hopefully improve in the near future.
We'll leave the PPC special-case as is for now.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230503184144.808478-1-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allowing guests to read unplugged memory simplified the bring-up of
virtio-mem in Linux guests -- which was limited to x86-64 only. On arm64
(which was added later), we never had legacy guests and don't even allow
to configure it, essentially always having "unplugged-inaccessible=on".
At this point, all guests we care about
should be supporting VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE, so let's
change the default for the 8.1 machine.
This change implies that also memory that supports the shared zeropage
(private anonymous memory) will now require
VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE in the driver in order to be usable by
the guest -- as default, one can still manually set the
unplugged-inaccessible property.
Disallowing the guest to read unplugged memory will be important for
some future features, such as memslot optimizations or protection of
unplugged memory, whereby we'll actually no longer allow the guest to
even read from unplugged memory.
At some point, we might want to deprecate and remove that property.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230503182352.792458-1-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since it's implementation on v8.0.0-rc0, having the PCI_ERR_UNCOR_MASK
set for machine types < 8.0 will cause migration to fail if the target
QEMU version is < 8.0.0 :
qemu-system-x86_64: get_pci_config_device: Bad config data: i=0x10a read: 40 device: 0 cmask: ff wmask: 0 w1cmask:0
qemu-system-x86_64: Failed to load PCIDevice:config
qemu-system-x86_64: Failed to load e1000e:parent_obj
qemu-system-x86_64: error while loading state for instance 0x0 of device '0000:00:02.0/e1000e'
qemu-system-x86_64: load of migration failed: Invalid argument
The above test migrated a 7.2 machine type from QEMU master to QEMU 7.2.0,
with this cmdline:
./qemu-system-x86_64 -M pc-q35-7.2 [-incoming XXX]
In order to fix this, property x-pcie-err-unc-mask was introduced to
control when PCI_ERR_UNCOR_MASK is enabled. This property is enabled by
default, but is disabled if machine type <= 7.2.
Fixes: 010746ae1d ("hw/pci/aer: Implement PCI_ERR_UNCOR_MASK register")
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Message-Id: <20230503002701.854329-1-leobras@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1576
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Nicholas Piggin