So that the following registers init could be flushed back to kvm.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Acked-by: Hollis Blanchard <hollis@penguinppc.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If -usbdevice is used on a machine with no USB busses, usb_create
will fail and return NULL. Patch below handles this failure gracefully
rather than crashing when we try to init the device.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Add a QEMU timer only when needed (timeout status not set, timeout
irq wanted and timer set).
This patch is required for Darwin. Patch has been tested under
FreeBSD, Darwin and Linux.
Signed-off-by: Frediano Ziglio <freddy77@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
o Implement receive overrun status. The FreeBSD uart driver
relies on this status in it's probe routine to determine the size
of the FIFO supported.
o As per the 16550 spec, do not overwrite the RX FIFO on an RX overrun.
o Do not allow TX or RX FIFO overruns to increment the data valid count
beyond the size of the FIFO.
o For reads of the IIR register, only clear the "TX holding register
emtpy interrupt" if the read reports this interrupt. This is required
by the specification and avoids losing TX interrupts when other,
higher priority interrupts (usually RX) are reported first.
Signed-off-by: Justin T. Gibbs <gibbs@FreeBSD.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci_data_write ignores high 8 bit in address,
so there seems to be no need to set them
in apb_pci.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
cc1: warnings being treated as errors
/src/qemu/hw/pl181.c: In function 'pl181_fifo_run':
/src/qemu/hw/pl181.c:185: error: 'value' may be used uninitialized in this function
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The PL181 data transfer loop incorrectly terminates after the last FIFO
word is popped, discarding the last 3 bytes of data on a write transfer.
Signed-off-by: Paul Brook <paul@codesourcery.com>
/src/qemu/hw/ide/core.c: In function 'ide_drive_pre_save':
/src/qemu/hw/ide/core.c:2740: warning: comparison is always false due to limited range of data type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If the device can't be created, don't leak the QemuOpts and release the id of
the device that should have been added by the failed device_add.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Hi,
Kevin and I have agreed on the approach for this one now. So here is
the latest version of the patch for QEMU, submitting e820 reservation
entries via fw_cfg.
Cheers,
Jes
Use qemu-cfg to provide the BIOS with an optional table of e820 entries.
Notify the BIOS of the location of the TSS+EPT range to by reserving
it via the e820 table.
This matches a corresponding patch for Seabios, however older versions
of Seabios will default to the hardcoded address range and stay
compatible with current QEMU.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Save/restore information necessary to continue in progress PIO/ATAPI CMD
transfers.
This includes the IO buffer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Michael noted we don't allow disabling of MSI for the virtio-serial-pci
device. Fix that.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 98b19252cf, all
serial devices declare MULTIPORT feature.
To allow 0.12 compatibility, we should clear this when
max_nr_ports is 1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
virtio-serial-pci can support multiple ports in the current development
version that will become 0.13. Add compatibility options for the 0.12
and 0.11 pc machine types.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The version 0.13 will be the new default and compatibility options will
be added to the 0.12 version.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I found that the QEMU USB keyboard support does not work properly with
the Set_Idle command. Once a non-zero value is given to Set_Idle,
then the keyboard reports an event on every poll - not based on the
time issued in the Set_Idle command.
I changed the code (see patch below) and it works for me. I'm not
that familiar with the qemu internals, so I'm not sure if this is the
best way to implement this feature.
-Kevin
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't raise irq when not enabled.
Raise irq on enabling if DMA_INTR is set
Don't clear irq unless it was raised by DMA, as there are other irq sources
Don't set DMA_INTR bit spuriously.
v1->v2:
- Don't clear irq unless it was raised by DMA
- Raise irq on enabling if DMA_INTR is set
- Assume revertion of 787cfbc432
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Cleanup versatile_pci: no need to re-set fields
to zero (pci core sets 0 already), use set_word
for status field. Compile-tested only, but seems obvious.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
This converts versatile_pci to use symbolic
constants. Verified by comparing binary to
original one.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Linux with CONFIG_PPC64 doesn't support ADB devices anymore, so we have to
use USB for keyboard and mouse.
This patch enables USB per default on U3 and adds a virtual keyboard and mouse
there.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While trying to find the right channel number for the DBDMA emulation I
stumbled across segmentation faults that were purely triggered by the guest.
The guest should never have the possiblity to segfault us, so let's check
all indirect function calls on a channel, so the code even works for channels
that have not been reserved.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per default Linux doesn't come with a lot of storage adapters enabled on
Mac configurations. The one that's pretty much always present is the pmac-ide,
while the cmd64x is almost never included in any distribution.
So let's switch to use the MacIO based IDE controller. There is corresponding
OpenBIOS code to get interrupts working properly.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Our guest systems need to know by how much the timebase increases every second,
so there usually is a "timebase-frequency" property in the cpu leaf of the
device tree.
This property is missing in OpenBIOS.
With qemu, Linux's fallback timebase speed and qemu's internal timebase speed
match up. With KVM, that is no longer true. The guest is running at the same
timebase speed as the host.
This leads to massive timing problems. On my test machine, a "sleep 2" takes
about 14 seconds with KVM enabled.
This patch exports the timebase frequency to OpenBIOS, so it can then put them
into the device tree.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The interrupt code as is didn't really work for me. I couldn't even convince
Linux to take interrupt 9 in an interrupt-map.
So let's do this right. Let's map all PCI interrupts to 0x1b - 0x1e. That way
we're at least a small step closer to what real hardware does.
I also took the interrupt pin to line conversion from OpenBIOS, which at least
assures us we're compatible with our firmware :-).
A dump of the PCI interrupt-map from a U2 (iBook):
00009000 00000000 00000000 00000000 ff97c528 00000034 00000001
0000d800 00000000 00000000 00000000 ff97c528 0000003f 00000001
0000c000 00000000 00000000 00000000 ff97c528 0000001b 00000001
0000c800 00000000 00000000 00000000 ff97c528 0000001c 00000001
0000d000 00000000 00000000 00000000 ff97c528 0000001d 00000001
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To ease debugging and to know what we're lacking, I found it really useful to
have an lspci dump of a real U3 based G5 around. So I added a comment for it.
If people don't think it's important enough to include this information in the
sources, just don't apply this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "Mac99" type so far defines a "U2" based configuration. Unfortunately,
there have never been any U2 based PPC64 machines. That's what the U3 was
developed for.
So let's split the Mac99 machine in a PPC64 and a PPC32 machine. The PPC32
machine stays "Mac99", while the PPC64 one becomes "Mac99_U3". All peripherals
stay the same.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Uninorth PCI bridge requires different layouts in its PCI config space
accessors.
This patch introduces a conversion function that makes it compatible with
the way Linux accesses it.
I also kept an OpenBIOS compatibility hack in. I think it'd be better to
take small steps here and do the config space access rework in OpenBIOS
later on. When that's done we can remove that hack.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove useless set to zero lines. Latency programming should be
done by BIOS, reset value is zero.
Add revision to APB, don't enable PCI_COMMAND_MASTER and set status
according to APB specification.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit c2039bd0ff made rom loading
automatic for non-PC architectures. Remove now mostly unused
conditional rom loading support.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch fixes 525e05147d.
pci host bridge doesn't have header type of bridge.
The check should be by header type, instead of pci class device.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Export the physical block size in the ATA IDENTIFY command. The
other topology values are not supported in ATA so skip them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export the physical block size in the READ CAPACITY (16) command,
and add the new block limits VPD page to export the minimum and
optiomal I/O sizes.
Note that we also need to bump the scsi revision level to SPC-2
as that is the minimum requirement by at least the Linux kernel
to try READ CAPACITY (16) first and look at the block limits VPD
page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export all topology information in the block config structure,
guarded by a new VIRTIO_BLK_F_TOPOLOGY feature flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The addition of the whole ATA IDENTIY page caused the config space to
go above the allowed size in the PCI spec, and thus the feature was
already reverted in the Linux guest driver and disabled by default in
qemu.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It's not needed to check the return of qobject_from_jsonf()
anymore, as an assert() has been added there.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix a race condition where qemu finds that there are not enough virtio
ring buffers available and the guest make more buffers available before
qemu can enable notifications.
Signed-off-by: Tom Lendacky <toml@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes a segfault due to buffer overrun in the usb-serial device.
The memcpy was incrementing the start location by recv_used yet, the
computation of first_size (how much to write at the end of the buffer
before wrapping to the front) was not accounting for it. This causes the
next element after the receive buffer (recv_ptr) to get overwritten with
random data.
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I have streaming audio devices working within qemu-kvm. This is a port
of the changes to qemu.
Streaming audio generates a series of isochronous requests that are
repetitive and time sensitive. The URBs need to be submitted in
consecutive USB frames and responses need to be handled in a timely manner.
Summary of the changes for isochronous requests:
1. The initial 'valid' value is increased to 32. It needs to be higher
than its current value of 10 since the host adds a 10 frame delay to the
scheduling of the first request; if valid is set to 10 the first
isochronous request times out and qemu cancels it. 32 was chosen as a
nice round number, and it is used in the path where a TD-async pairing
already exists.
2. The token field in the TD is *not* unique for isochronous requests,
so it is not a good choice for finding a matching async request. The
buffer (where to write the guest data) is unique, so use that value instead.
3. TD's for isochronous request need to be completed in the async
completion handler so that data is pushed to the guest as soon as it is
available. The uhci code currently attempts to process complete
isochronous TDs the next time the UHCI frame with the request is
processed. The results in lost data since the async requests will have
long since timed out based on the valid parameter. Increasing the valid
value is not acceptable as it introduces a 1+ second delay in the data
getting pushed to the guest.
4. The frame timer needs to be run on 1 msec intervals. Currently, the
expire time for the processing the next frame is computed after the
processing of each frame. This regularly causes the scheduling of frames
to shift in time. When this happens the periodic scheduling of the
requests is broken and the subsequent request is seen as a new request
by the host resulting in a 10 msec delay (first isochronous request is
scheduled for 10 frames from when the URB is submitted).
[ For what's worth a small change is needed to the guest driver to have
more outstanding URBs (at least 4 URBs with 5 packets per URB).]
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The write the the PA_POWOFF register is currently ignored. Fix that by
calling qemu_system_shutdown_request() when a poweroff is requested.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
typo in c021f8e65f.
comparison fix.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When several PCI bridges were in use, monitor command "info pci" would
enter into infinite loop. Buses behind the bridge were not discoverable
because secondary and subordinate bus numbers were not used properly.
Other buses were not found because bus search terminated on first miss.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The vmport "device" accesses the VCPU registers, so it requires proper
cpu_synchronize_state. Add it to vmport_ioport_read, which also
synchronizes vmport_ioport_write.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This provides the same information as reverted commit 2ba6edf0. Not
much, just better than nothing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Option "-device DRIVER,?" and monitor command "device_add DRIVER,?"
print the supported properties instead of creating a device. The
former also terminates the program.
This is commit 2ba6edf0 (just reverted) done right.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 2ba6edf0dd.
The commit has two issues:
* When it runs from the monitor, e.g. "device_add e1000,?", it prints
to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 922910ce42.
The commit has four issues:
* When it runs from the monitor, e.g. "device_add e1000,mac=?", it
prints to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,mac=?".
* It has an undocumented side effect on -global: "-global e1000.mac=?"
prints help, but only when we actually add an e1000 device.
* It does not work for properties that accept the value "?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Help was shoehorned into device creation, qdev_device_add(). Since
help doesn't create a device, it returns NULL, which looks to callers
just like failed device creation. Monitor handler do_device_add()
doesn't care, but main() exits unsuccessfully.
Move help out of device creation, into new qdev_device_help().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If an I/O request fails right away instead of getting an error only in the
callback, we still need to consider rerror/werror.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Current code assumes that only write requests are ever going to be restarted.
This is wrong since rerror=stop exists. Instead of directly starting writes,
use the same request processing as used for new requests.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We need a function that handles a single request. Create one by splitting out
code from virtio_blk_handle_output.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes CONFIG_FB_CIRRUS for Linux guests and probably much more:
When switching away from linearly mapped vram, we also have to restore
the I/O handlers for the LFB.
This regression was once introduced by commit 2bec46dc97.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit enables one to use multiple virtio-serial devices and to
assign ports to arbitrary devices like this:
-device virtio-serial,id=foo -device virtio-serial,id=bar \
-device virtserialport,bus=foo.0,name=foo \
-device virtserialport,bus=bar.0,name=bar
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
sparc64 timer has tick counter which can be set and read,
and tick compare value used as deadline to fire timer interrupt.
The timer is not used as periodic timer, instead deadline
is set each time new timer interrupt is needed.
v3 -> v4:
- coding style
v2 -> v3:
- added missing timer debug output macro
- CPUTimer struct and typedef moved to cpu.h
- change CPU_SAVE_VERSION to 6, older save formats not supported
v1 -> v2:
- new conversion helpers cpu_to_timer_ticks and timer_to_cpu_ticks
- save offset from clock source to implement cpu_tick_set_count
- renamed struct sun4u_timer to CPUTimer
- load and save cpu timers
v0 -> v1:
- coding style
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Buffer block writes to avoid flushing every word access onto backing
storage device. This significantly speeds up flash emulation for flashes
connected through an 8 or 16-bit bus combined with backing storage (-pflash).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
When using ballooning to manage overcommitted memory on a host, a system for
guests to communicate their memory usage to the host can provide information
that will minimize the impact of ballooning on the guests. The current method
employs a daemon running in each guest that communicates memory statistics to a
host daemon at a specified time interval. The host daemon aggregates this
information and inflates and/or deflates balloons according to the level of
host memory pressure. This approach is effective but overly complex since a
daemon must be installed inside each guest and coordinated to communicate with
the host. A simpler approach is to collect memory statistics in the virtio
balloon driver and communicate them directly to the hypervisor.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Win32 suffers from a very big memory leak when dealing with SCSI devices.
Each read/write request allocates memory with qemu_memalign (ie
VirtualAlloc) but frees it with qemu_free (ie free).
Pair all qemu_memalign() calls with qemu_vfree() to prevent such leaks.
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
PCI bridges' qdev info structures must indicate bridge header type,
otherwise critical bridge registers (esp. PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS, PCI_SUBORDINATE_BUS) will not be writable.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This file was renamed to ease the reviews of the recent changes
that went in.
Now that the changes are done, rename the file back to its original
name.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If migration takes place between write of the bmdma address register and
write of the command register (to initiate DMA), the destination will
not properly start the DMA op, hanging the guest:
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd c8/00:16:41:00:00/00:00:00:00:00/e0 tag 0 dma 11264 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
Fix by sending current transfer information in the migration data.
We need to update ide version to 4 for this to work. As we don't
have subsectios, we need to chain the update increase until
vmstate_ide_pci (quintela)
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit completes the do_pci_info() conversion to
QObject by adding support to PCI bridge devices.
This is done by recursively adding devices in the
"pci_bridge" key.
IMPORTANT: This code is being added separately because I could
NOT test it properly. According to Michael Tsirkin, it depends
on ultrasparc and it would take time to do the proper setup.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The returned QObject is a QList of all buses. Each bus is
represented by a QDict, which has a key with a QList of all
PCI devices attached to it. Each device is represented by
a QDict.
As has happended to other complex conversions, it's hard to
split this commit as part of it are new functions which are
called by each other.
IMPORTANT: support for printing PCI bridge attached devices
is NOT part of this commit, it's going to be added by the
next commit, as it's untested.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When called with property value "?",
a help text will be printed (instead of an error message).
This is useful for command lines like
qemu -device e1000,mac=?
and is already standard for other command line options.
A better help text could be provided by extending
the Property structure with a desc field.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When called with property "?", a list of supported
properties will be printed (instead of an error message).
This is useful for command lines like
qemu -device e1000,?
and was already standard for other options like model=?
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix HdrS offsets for Sparc64. The initrd address must be offset by
KERNBASE.
Use rom_ptr mechanism to actually write to the kernel image.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
When wcycle is non zero the area is already opened for readable IO.
Avoiding the re-registration of the memarea significantly speeds up
the flash emulation. In particular for flashes connected through 8 or
16-bit buses.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
Flashes connected through an 8 bit bus cannot handle write buffers
larger than 256 bytes.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
According to Sun4M System Architecture Manual chapter 5.3.2, a limit
of 0 will not generate interrupts.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit 930c86820e introduced a regression to eth_send: eth_tx_desc_put
manipulates the host's tx descriptor copy before writing it back, but
two lines down the descriptor is evaluated again, leaving us with an
invalid next address if host and guest endianness differ. So this was
the actual issue commit 2e87c5b937 tried to paper over.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: malc <av1474@comtv.ru>
Commit b3a219883e uncovered that we attached the Wolfson with an I2C
address shifted left by one. Fixing this makes sound work again for
the Musicpal.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: malc <av1474@comtv.ru>
Byte swap PCI config values.
Remove old bogus PCI config mechanism so that device 0:0.0 can be probed.
This requires OpenBIOS r667.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This commit enables the use of MSI interrupts for virtqueue
notifications for ports. We use nr_ports + 1 (for control channel) msi
entries for the ports, as only the in_vq operations need an interrupt on
the guest.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit adds a simple chardev-based serial port. Any data the guest
sends is forwarded to the chardev and vice-versa.
Sample uses for such a device can be obtaining info from the guest like
the file systems used, apps installed, etc. for offline usage and
logged-in users, clipboard copy-paste, etc. for online usage.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The port 'id' or number is internal state between the guest kernel and
our bus implementation. This is invocation-dependent and isn't part of
the guest-host ABI.
To correcly enumerate and map ports between the host and the guest, the
'name' property is used.
Example:
-device virtserialport,name=org.qemu.port.0
This invocation will get us a char device in the guest at:
/dev/virtio-ports/org.qemu.port.0
which can be a symlink to
/dev/vport0p3
This 'name' property is exposed by the guest kernel in a sysfs
attribute:
/sys/kernel/virtio-ports/vport0p3/name
A simple udev script can pick up this name and create the symlink
mentioned above.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Via control channel messages, the guest can tell us whether a port got
opened or closed. Similarly, we can also indicate to the guest of host
port open/close events.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit converts the virtio-console device to create a new
virtio-serial bus that can host console and generic serial ports. The
file hosting this code is now called virtio-serial-bus.c.
The virtio console is now a very simple qdev device that sits on the
virtio-serial-bus and communicates between the bus and qemu's chardevs.
This commit also includes a few changes to the virtio backing code for
pci and s390 to spawn the virtio-serial bus.
As a result of the qdev conversion, we get rid of a lot of legacy code.
The old-style way of instantiating a virtio console using
-virtioconsole ...
is maintained, but the new, preferred way is to use
-device virtio-serial -device virtconsole,chardev=...
With this commit, multiple devices as well as multiple ports with a
single device can be supported.
For multiple ports support, each port gets an IO vq pair. Since the
guest needs to know in advance how many vqs a particular device will
need, we have to set this number as a property of the virtio-serial
device and also as a config option.
In addition, we also spawn a pair of control IO vqs. This is an internal
channel meant for guest-host communication for things like port
open/close, sending port properties over to the guest, etc.
This commit is a part of a series of other commits to get the full
implementation of multiport support. Future commits will add other
support as well as ride on the savevm version that we bump up here.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
VIRTIO_PCI_QUEUE_MAX is redefined in hw/virtio.c. Let's just keep it in
hw/virtio.h.
Also, bump up the value of the maximum allowed virtqueues to 64. This is
in preparation to allow multiple ports per virtio-console device.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Instead of using the field 'readonly' of the BlockDriverState struct for passing the request,
pass the request in the flags parameter to the function.
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds compat property entries for ide-disk.ver and
scsi-disk.ver to pc-0.10 and pc-0.11. With this patch applied
the scsi and ide disks report "0.10" and "0.11" as version when
you start qemu with "-M pc-0.10" or "-M pc-0.11".
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to scsi-disk which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device lsi
-device scsi-disk,drive=disk,bus=scsi.0,unit=0,ver=42
You can also switch the version for all scsi drives using:
-global scsi-disk.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to ide-drive which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device ide-drive,bus=ide.0,unit=0,drive=disk,ver=42
You can also switch the version for all ide drives using:
-global ide-drive.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 747bbdf7 QEMU_WARN_UNUSED_RESULT is never defined as it is
conditional on a define from config-host.h which is included only later.
Include that file earlier to get the warnings back.
Reactivating it unfortunately leads to some warnings about unused qdev_init
results. These calls are changed to qdev_init_nofail to avoid build failures.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently we do not implement VLAN tagging for rtl8139(C+),
still data is read from ring buffer headers.
- augment unused assignment with TODO item
- cast txdw1 to void for now
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* Handling of multicast list was missing.
* Multicast all was missing.
* Promiscuous mode for multicast frames was wrong.
This patch is a step to synchronize my maintainer version
of eepro100.c (git://repo.or.cz/qemu/ar7.git) with the
version integrated in QEMU.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Handling of transmit commands is rather complex,
so about 80 lines of code were moved from function
action_command to the new function tx_command.
The two new values "tx" and "cb_address" in the
eepro100 status structure made this possible without
passing too many parameters.
In addition, the moved code was cleaned a little bit:
old comments marked with //~ were removed, C++ style
comments were replaced by C style comments, C++ like
variable declarations after code were reordered.
Simplified mode is still broken. Nor did I fix
endianess issues. Both problems will be fixed in
additional patches (which need this one).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Don't clear interrupts on disabling, because
* Sun4M_SystemArchitecture_edited2.pdf doesn't describe
that masking or un-masking IRQ shall clear pending ones.
* Field tests also show that SPARCstation-20 doesn't
clear them.
* The patch makes Solaris 2.5.1/2.6 boot ~1500 times
faster (~20 seconds instead of ~8 hours)
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Random reading depends on having the last row/page latched and not beeing
clobbered between read and any following random reads.
Also, s->iolen must be updated when loading the io/data register with
randomly accessed flash data.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
This patch adds hardware cursor feature to SM501 graphics chip emulation,
to make the graphic console more useful for QEMU SH4 users.
Signed-off-by: Shin-ichiro KAWASAKI <kawasaki@juno.dti.ne.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As pointed out by clang size is only ever written to, but never actually
used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
clang-analyzer points out value assigned to 'len' is not used.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Although the value stored to 'addr' is used in the enclosing expression,
the value is never actually read from 'addr'.
Probably a typo.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
pci_get_byte, pci_get_word, pci_get_long and pci_get_quad
all take a const uint8_t pointer, because they only read
the configuration data.
Their prototypes should reflect this fact.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use new way to associate ROM files to devices.
Currently, there is only a ROM file for i82559er
included in QEMU, so the patch does not add
.romfile for the other devices.
When flexible mode is fixed in eepro100, adding
more ROM files will be possible. It should be
possible to create them from pxe-i82559er.bin,
because etherboot uses the same driver for all
eepro100 devices (only PCI ids differ).
Maybe it is even possible to create a single
pxe-i8255x.bin which supports all eepro100 devices
(not supported with current etherboot).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The numerical value was wrong (0x2800 instead of 0x0280)
which indeed did not make sense.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mac feature bit isn't going to work as all network cards already have a
'mac' property to set the mac address. Remove it from mask and add in
get_features.
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Without this fix, guest crashes with drive=virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
So '-M pc-0.10' and '-M pc-0.11' will use the fw_cfg rom load method
by default.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a pci bus property 'rombar' which specifies whenever
the pci rom should be loaded via pci rom bar (default) or via fw_cfg.
The later can be used for compatibility with older qemu versions where
no pci rom bar is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch changes the way rom loading via fw_cfg is handled.
Instead of having pc_init1() call a function which passed all
roms to the firmware config we simply pass a pointer to fw_cfg
to the rom loader.
Advantage: loading roms via firmware works also for devices which
are initialized after pc_init1(), i.e. everyting added via -device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
- make dir argument mandatory, we allways have one anyway
(vgaroms or genroms).
- check for duplicates, skip loading if found.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
- Drop extra file argument from rom_add_file().
- Drop fw_dir check in do_info_roms, we allways have a dir name.
- code style fixes.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a new machine type for qemu 0.12.
Also fixup the 0.11 machine type: msi for virtio-blk-pci was enabled
after the 0.11 release, so turn it off in the 0.11 machine type.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since patch ed757e140c0ada220f213036e4497315d24ca8bct, virtio will
sometimes clear all status registers on bus master disable, which loses
information such as VIRTIO_CONFIG_S_FAILED bit. This is a result of
a patch being misapplied: code uses ! instead of ~ for bit
operations as in Yan's original patch. This obviously does not make
sense.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add feature bits as properties to virtio. This makes it possible to e.g. define
machine without indirect buffer support, which is required for 0.10
compatibility, or without hardware checksum support, which is required for 0.11
compatibility. Since default values for optional features are now set by qdev,
get_features callback has been modified: it sets non-optional bits, and clears
bits not supported by host.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rename features->guest_features. This is
what they are, avoid confusion with
host features which we also need to keep around.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This adds "bit" property type, which is a boolean stored in a 32 bit
integer field, with legal values on and off. Will be used by virtio for
feature bits.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All callers of lsi_reselect have a lsi_request struct at hand anyway.
So just pass it directly instead of having lsi_reselect search for it
using the tag.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Right now lsi_request is allocated when a request is queued and released
when a request is unqueued. With this patch applied the lsi_request is
kept for the whole lifetime of the scsi request.
Rationale: We can use it for per-request data then. The patch does that
already for the request tag.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Replace the funky array logic for queued commands with standard
qemu list functions. Also rename lsi_queue to lsi_request.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Check that the cursor dimensions passed from the guest for the
DEFINE_CURSOR command don't overflow the available space in the
cursor.image[] or cursor.mask[] arrays before copying data from the
guest into those arrays.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
cpu_check_irqs
- handle SOFTINT register TICK and STICK timer bits
- only check interrupt levels greater than PIL value
- handle preemption by higher level traps
cpu_exec
- handle CPU_INTERRUPT_HARD only if interrupts are enabled
- PIL 15 is not special level on sparcv9
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move multiboot loading code into separate files as suggested by Alex Graf.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add generic support for debugging consoles (simple I/O ports which
when written to cause debugging output to be written to a target.)
The current implementation matches Bochs' port 0xe9, allowing the same
debugging code to be used for both Bochs and Qemu.
There is no vm state associated with the debugging port, simply
because it has none -- the entire interface is a single, stateless,
write-only port.
Most of the code was cribbed from the serial port driver.
v2: removed non-ISA variants (they can be introduced when/if someone
wants them, using code from the serial port); added configurable
readback (Bochs returns 0xe9 on a read from this register, mimic that
by default) This retains the apparently somewhat controversial user
friendly option, however.
v3: reimplemented the user friendly option as a synthetic option
("-debugcon foo" basically ends up being a parser-level shorthand for
"-chardev stdio,id=debugcon -device isa-debugcon,chardev=debugcon") --
this dramatically reduced the complexity while keeping the same level
of user friendliness.
v4: spaces, not tabs.
v5: update to match current top of tree. Calling qemu_chr_open()
already during parsing no longer works; defer until we are parsing the
other console-like devices.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
According to C99, realloc(non_null, 0) != free(non_null), that's why
it is forbidden in QEMU.
When there are no symbols, nsyms equals to 0. Free the syms structure
and set it to NULL instead of reallocating it with a size of 0.
This fixes -kernel with stripped kernels.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
CC i386-softmmu/pc.o
cc1: warnings being treated as errors
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c: In function 'load_multiboot':
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c:614: error: ignoring return value of 'fread', declared with attribute warn_unused_result
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c: In function 'load_linux':
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c:888: error: ignoring return value of 'fread', declared with attribute warn_unused_result
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c:889: error: ignoring return value of 'fread', declared with attribute warn_unused_result
make[1]: *** [pc.o] Error 1
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Store the register values in native endianness, by dropping all the
endianness conversion functions, and converting the endianness in
dbdma_readl/dbdma_writel instead.
Also guard the endianness conversion with TARGET_WORDS_BIGENDIAN to
simulate the backward connection of the bus.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Similarly to what has been done in e405a2ba91,
ignore rom intended to be loaded by the bios in find_rom() and rom_copy().
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The first such option rom will load at address 0, which isn't very nice,
and the second will report a conflict and abort, which is horrible.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Link to data sheet at intel.com so people can find it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
use range helper function in i440fx_write_config().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Define symbolic value in i440fx configuration space
for 0x59, 0x5f and 0x7f and use them.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use range helper function in msix_write_config().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use range helper function in pm_write_config().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They call only pci_default_{read, write}_config().
So they aren't necessary.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
include pci_regs.h and remove duplicated defines.
And remove unused PCI_REVISION and PCI_SUBDEVICE_ID.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Import Linux pci_regs.h. Later PCI register definitions in pci.h
will be eliminated.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To match Linux PCI register definition,
rename PCI_SUBVENDOR_ID to PCI_SUBSYSTEM_VENDOR_ID.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCIBus::config_reg isn't used anymore, so remove it.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI_STATUS_DEVSEL is unused, and it also
has a different name in pci_regs.h
Remove.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
will be used by ensoniq emulation
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change in meaningful ways.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
will be used by eepro100.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated
object binary does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
Add core tile memeory to the RealView PBX-A9 board. Document the
memeory maps that are known to work with the qemu bootloader.
Signed-off-by: Paul Brook <paul@codesourcery.com>
For what I know DCR is always 32 bits wide, so we should also use uint32_t to
pass it along the stacks.
This fixes a warning when compiling qemu-system-ppc64 with KVM enabled, making
it compile without --disable-werror
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Fix the alternate time base the same way as the default timebase. SPR_ATBL
should return a 64-bit value on 64 bit implementations.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On PPC we have a 64-bit time base. Usually (PPC32) this is accessed using
two separate 32 bit SPR accesses to SPR_TBU and SPR_TBL.
On PPC64 the SPR_TBL register acts as 64 bit though, so we get the full
64 bits as return value. If we only take the lower ones, fine. But Linux
wants to see all 64 bits or it breaks.
This patch makes PPC64 Linux work even after TB crossed the 32-bit boundary,
which usually happened a few seconds after bootup.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Also change the New World default CPU to 970FX for ppc64,
since the G4 is a 32-bit CPU.
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
ROMs need to be loaded if they are anywhere in the requested area, not
only at the very beginning. This fixes Multiboot with ELF kernels that
have more than one program header.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It was possible to load roms at address 0, but commit
632cf034b4 started to forbid that, which
broke at least ARM versatile.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When using the escc with Linux, we need interrupts. So instead of creating
a dummy device, let's just map them to the openpic we have anyways.
This makes Linux on PPC64 with console=ttyPZ0 work.
Obviously, this change needs to be reflected in openbios. Patch for that
follows this one. Please update the binary then.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When lowering an IRQ line, we search for the line we're supposed to lower.
Usually we run into an optimization there that queues up interrupts. This
queue ends with -1. Unfortunately we didn't set the first item to -1.
This patch fixes this, making interrupts work on PPC64.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Otherwise, the driver does not work in Linux after the INT_DISABLE changes in
PCI.
Michael Tsirkin had a patch to do this, I'm not sure what happened to it.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Convert musb fifo to 8bit to allow 8/16/32bit access
MUSB allows reading and writing to the fifo in 32/16/8 bit
width. The Linux kernel does this sometimes, most usually at
the end of writing the packet to allow packet to end at a
odd bytecount.
Convert the fifo to 8bit allows removing lots of shifts
which shows that the fifo is more natural as 8bit.
While at it, add multiple missing register definitions and
and cleanup debug prints.
Signed-off-by: Riku Voipio <riku.voipio@nokia.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that we load the option roms via fw_cfg, we can stop copying
them to the 0xc000 -> 0xe000. The patch does just that.
Also the rom loader gets simplified as all remaining users of the
rom loader load the bits at a fixed address so the packing and
aligning logic can go away.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
roms: use fw_cfg for vgabios and option rom loading, additionally to
deploying them the traditional way (copy to 0xc0000 -> 0xe0000 range).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a file transfer interface to fw_cfg. Intended to be
used for passing non-pci option roms and vgabios to seabios. Namespace
is modeled after the existing cbfs filesystem support in seabios.
Reading the new FW_CFG_FILE_DIR entry returns a file list.
Fields there are in network byte order (aka bigendian).
aliguori: fix fw_cfg.h for multiboot.bin, add proper fw_cfg.h declarations,
quiet fprintf() in fw_cfg.c
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a romfile property to the pci bus. It allows to specify
a romfile to load into the rom bar of the pci device. The default value
comes from a new field in PCIDeviceInfo. The property allows to change
the file and also to disable the rom loading using an empty string.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently, we preload option roms into the option rom space in memory. This
prevents DDIM from functioning correctly which severely limits the number
of roms we can support.
This patch introduces a pci_add_option_rom() which registers the
PCI_ROM_ADDRESS bar which points to our option rom. It also converts over
the cirrus vga adapter, the rtl8139, virtio, and the e1000 to use this
new mechanism.
The result is that PXE boot functions even with three unique types of cards.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
SCSI controllers have no trouble existing without any attached
disks. This could be achieved with the (legacy) monitor syntax
pci_add pci_addr=auto storage if=scsi
This is now denied with
scsi requires a backing file/device.
failed to add if=scsi
There is no need for this denial and it breaks compatability
with existing QEMU usage, so remove the check for presence
of a drive.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Floppy used the io_base address to register savevm region.
This reverts commit 2966b390d0.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The cursor pixmap size we calculate later ends up being 4096 dwords
long by the looks of it. This boots an F12 LiveCD now.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch enables dirty log tracking whenever it's needed and disables it
when it is not.
We unconditionally enable dirty log tracking on reset, restart dirty log
tracking when PCI IO regions are remapped, and disable/enable it based on
commands from the guest.
Rebased-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
VMware VGA requires that the depth presented to the guest is the same as the
DisplaySurface that it renders to. This is because it performs a very simple
memcpy() to blit from one surface to another.
We currently hardcode a 24-bit depth. The surface allocator for SDL may, and
usually will, allocate a surface with a different depth causing screen
corruption.
This changes the code to allocate the DisplaySurface before initializing the
device which allows the depth of the DisplaySurface to be used instead of
hardcoding something.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Apparently, VBE maps the VGA vram to a fixed physical location. KVM requires
that all mappings of the VGA vram have dirty tracking enabled on them. Any
access to the VGA vram through the VBE mapping currently fails to result in
dirty page tracking updates causing a black screen.
This is the true root cause of VMware VGA not working correctly under KVM and
likely also an issue with some of the std-vga black screen issues too.
Cirrus does not enable VBE so it would not be a problem when using Cirrus.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rebased-by: Dave Airlie <airlied@redhat.com>
Add a error message in case we fail to parse a qdev property.
Also make qemu not abort() in case setting a global property can't be
set. This used to be a clear programming error. The introduction of
the -global switch changed that though, so better exit instead (after
printing the new error message).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rebased to master, adapted to device renaming by armbru,
no other changes.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Check rom_load_all() return value.
Also don't make option rom loading failure fatal.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Split default_drive into default_{floppy,cdrom,sdcard}.
Also add QEMUMachine flags to disable them per machine.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The multiboot implementation assumed that there is only one program header
(which contains the entry point) and that the entry point is at the start of
the code. This doesn't hold true generally and caused too little data to be
loaded.
Fix the loading code to pass the whole loaded data to the Multiboot Option ROM.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 0ea5709a32085f7d14901a09d12bd35f9b267607.
Per discussion with Michael Tsirkin, this is too risky for 0.12
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently only the S390 KVM target works. To keep users from accidently not
using KVM, let's not even initialize the machine when KVM is not used.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Currently we always set the "config space changed" bit to 1 when triggering
any virtio interrupt. While that worked in 2.6.27, newer kernels interpret
that value as "only the config space changed and nothing else happened".
Since we usually trigger interrupts to tell the guest that something did
happen, we just not tell it the config space changed for now until we
implement the correct callback for that.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We used to always create one single virtio console device. This breaks when
either zero of multiple virtio console devices are requested, so let's use
the same code as on x86.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
nd->model keeps dynamically allocated model names.
So casting of a constant string is wrong here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When emulating user-mode only, there's no reason to exit
the translation block to effect a call_pal. We can generate
a move to/from the unique slot directly.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This is a workaround only, and is a partial revert
of a few changes to BMDMAState which removed pci_dev
field on the way.
- cmd646 pci_from_bm() expects bm->unit value to
correspond with bm data being passed to callback
as opaque pointer. This breaks when write to dma
control register of second channel happens when no
dma operation is in progress, so bm->unit is zero
for second channel, and pci_from_bm() returns garbage
pointer. Crash happens shortly after that while
dereferencing that pointer.
v0->v1: cleaned up dead code from pci_from_bm.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
s390 code has an obvious typo, which results in:
hw/s390-virtio.c: At top level:
hw/s390-virtio.c:249: error: request for member ‘no_vga’ in something not a structure or union
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Building on 32 bit host we get:
hw/s390-virtio.c: In function ‘s390_init’:
hw/s390-virtio.c:184: error: integer constant is too large for ‘unsigned long’ type
64 bit values must be ULL.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Stepping through the SS-5's OBP initialization routines
it looks like reading fdc main status register should
clear the fd interrupt.
The patch doesn't fix problems with fdc on sparc platform,
it only fixes fdc detection.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Implement a stub for the AFX register on SparcStation-5.
This stub is needed for running the original SS-5 OBP
instead of OpenBIOS (which allows to boot Solaris 2.5.1
and Solaris 2.6 kernels).
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
According to the SCSI-2 specification,
http://ldkelley.com/SCSI2/SCSI2/SCSI2/SCSI2-08.html#8.2.5 ,
"if the allocation length of the command descriptor block (CDB) is too
small to transfer all of the parameters, the additional length shall
not be adjusted to reflect the truncation."
The 36 mandatory bytes of response are written to outbuf, and then
only the length requested in CDB is transferred.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Return a QDict with information about the just added device.
This commit should not change user output.
Please, note that this patch does not do error handling
conversion. In error conditions the handler still calls
monitor_printf().
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch fills the DriveInfo->unit after hotplugging a scsi disk.
It makes a difference when auto-assigning a scsi id, where unit was
left filled with '-1' instead of the actual scsi id.
With this patch applied the the drive naming logic in drive_init() works
as good as it did in previous releases. Which means it works fine with
a single scsi bus.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Current PCI code will simply hw_error() and thus abort in case no free
PCI slot is available or the requested PCI slot is already in use by
another device. For the hotplug case this behavior is not acceptable.
This patch makes qemu pass up the error properly, so the calling code
can decide whenever it wants to exit with an error (on startup) or
whenever it wants to continue (hotplug).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The PCI bus on x86 requires ACPI for hotplug support, thus disbling ACPI
also disables hotplug for the PCI bus. This patch makes qemu check
whenever the PCI bus in question can handle hotplug before trying to add
devices. This is needed because qdev will abort() on any attempt to
hotplug devices into a non-hotpluggable bus.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All "normal" system emulation targets in qemu I'm aware of display
output on either VGA or serial output.
Our S390x virtio machine doesn't have such kind of legacy hardware. So
instead we need to default to a virtio console.
Add flags to QEMUMachine to indicate which kind of default devices make
sense for the machine in question. Use it for S390x: enable virtcon,
disable serial, parallel and vga.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
i.e. -global PCI.<property>=<value> will set a default property for all
PCI devices. Also works for the compat properties used by machine
types.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch renames the compat properties into global properties and
makes them more generic. The compatibility stuff is only one of
multiple possible users now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Device names with whitespace require quoting in the shell and in the
monitor. Some of the offenders are also overly long. Some have a
more convenient alias, some don't.
The place for verbose device names is DeviceInfo member desc. The
name should be short & sweet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Using the qdev name for the product description makes for inconvenient
qdev names.
Put the product description in new USBDeviceInfo member product_desc.
Make usb_qdev_init() use it. No user or guest visible change, since
the value is still the same.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It's not a device name, it's the USB product description string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
On hosts without high-res timers it is impossible to inject rtc interrupt
faster then 1kHz. Windows sometimes configures RTC to generate 1kHz
interrupts, so we can't inject missed interrupts when running on such
hosts. Always injecting an interrupt on REG_C read is also not an option
since Windows wait for REG_C to become zero with interrupt disabled
during boot. This patch uses mixed approach: accelerate timer + inject
up to 1000 interrupts on REG_C read.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
migrating between hosts which have different features
might break silently, if the migration destination
does not support some features supported by source.
Prevent this from happening by comparing acked feature
bits with the mask supported by the device.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This just adds the rom file to the vmware SVGA chipset so it boots.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Interrupt disable bit is mandatory in PCI spec.
Implement it to make devices spec compliant.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
interrupt status is a mandatory feature in PCI spec,
so devices must implement it to be spec compliant.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
This rearranges code in preparation for interrupt state
implementation.
Changes:
- split up bus walk away from interrupt handling
into a subroutine
- change irq_state from an array to bitmask
- verify that irq_state values are 0 or 1 on load
There are no functional changes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
Function mask is a mandatory feature in MSIX
spec so not implementing it is a spec violation.
Implement.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
rename ENABLE_OFFSET -> CONTROL_OFFSET, since
same byte includes function mask.
This is in preparation for function mask support.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to use the new S390x virtio bus we just introduced, we also
need a machine description that sets up the machine according to our
PV specification.
Let's add that machine description and be happy!
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On S390x we don't want to go through the hassle of emulating real existing
hardware, because we don't need to for running Linux.
So let's instead implement a machine that is 100% based on VirtIO which we
fortunately implement already.
This patch implements the bus that is the groundwork for such an S390x
virtio machine.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This implements the audio control or volume read support as needed by
some systems. A Conectiva Parolin system required this to detect an IDE
device as CD-ROM, through the CDVOLREAD ioctl.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some PAGE constants were used instead of the macros we already have
defined in internal.h.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* buf was too small for longer register names.
* Use consistent upper case for nouns in register names.
* Use better name for array with e100 register names.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This should avoid truncating the register name when debugging.
Signed-off-by: David Benjamin <davidben@mit.edu>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In mb_mod_length a return value is stored that is negative in error case. With
an unsigned type the check goes wrong.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch fixes the follow error when LSI_DEBUG is set.
CC libhw64/lsi53c895a.o
cc1: warnings being treated as errors
qemu/hw/lsi53c895a.c: In function 'lsi_io_mapfunc':
qemu/hw/lsi53c895a.c:1932: error: format '%08x' expects type 'unsigned int', but argument 2 has type 'pcibus_t'
qemu/hw/lsi53c895a.c: In function 'lsi_ram_mapfunc':
/qemu/hw/lsi53c895a.c:1947: error: format '%08x' expects type 'unsigned int', but argument 2 has type 'pcibus_t'
qemu/hw/lsi53c895a.c: In function 'lsi_mmio_mapfunc':
qemu/hw/lsi53c895a.c:1957: error: format '%08x' expects type 'unsigned int', but argument 2 has type 'pcibus_t'
make[1]: *** [lsi53c895a.o] Error 1
make: *** [subdir-libhw64] Error 2
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
A code review run by Steve Grubb complained about code in e1000.c:
In hw/e1000.c at line 89, vlan is declared to be 4 bytes.
At line 382 is an attempt to do a memmove over it with a size of 12.
This was fixed by splitting the memmove in two calls and
adding a comment to the declaration of vlan and data.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Vendor identification, product identification and product revision level
should be padded with spaces without a terminating NULL character, see
SCSI-2 standard, 8.2.5.1 Standard INQUIRY data.
Signed-off-by: Laszlo Ast <laszlo.ast@siemens-enterprise.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some recent change made PPC guests always start at address 0x0 because env
isn't synced to kvm_state on first bootup.
I'm not sure if this is the correct bugfix, but at least it makes PPC boot
again with KVM enabled.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cirrus vga has a copy of many PCI macros,
and it doesn't even use them. Clean up.
We also don't need to override header type
as it is NORMAL by default.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
PCI memory should be disabled at reset, otherwise
we might claim transactions at address 0.
I/O should also be disabled, although for cirrus
it is harmless to enable it as we do not
have I/O bar.
Note: bios fix needed for this patch to work
was already applied:
previously bios incorrently assumed that it does not
need to enable i/o unless device has i/o bar.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Either rename variables and functions to refer to write errors (which is what
they actually do) or introduce a parameter to distinguish reads and writes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In order to allow proper progress reporting to the monitor that
initiated the migration, forward the monitor reference through the
migration layer down to SaveLiveStateHandler.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When the size that we want to transmit is in another field, but in an
unit different that bytes
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Support for buffer that are pointed by a pointer (i.e. not embedded)
where the size that we want to use is a field in the state.
We also need a new place to store where to start in the middle of the
buffer, as now it is a pointer, not the offset of the 1st field.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The critical part of this change is how to deal with simultaneaous
generation of interrupts. The only (normal) case when this happens in
the emulation is near simultaneous reselection + selection. If selection
comes first, there is no problem, since the target attempting
reselection loses the arbitration (in the emulation it only means that
the reselect function will not be started). In the worst case the host
adapter is reselected, but the device driver already started a
selection, so we jump to the alternative address to handle the
situation.
The SCRIPTS code can trigger another interrupt to notify the driver that
the new task has to be postponed. I suppose that on real hardware there
is enough time after the reselection interrupt to set the SIP bit before
the next interrupt comes, so it would result in 2 stacked interrupts (a
SCSI and a DMA one). However, in the emulation there is no interrupt
stacking, so there is a good chance that the 2 interrupts will get to
the interrupt handler at the same time.
Nevertheless, it should not make a big difference in interrupt handling,
since in both cases both interrupts have to be fetched first, and after
that the new task (that failed during the selection phase) has to be
prepared/reset for a later restart, and the reconnected device has to be
serviced.
The changes do not modify the host adapter's behavior if this interrupt
is not enabled.
See also LSI53C895A technical manual, SCID and SIEN0.
Signed-off-by: Laszlo Ast <laszlo.ast@siemens-enterprise.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
See SCSI-2, 6.5 Message system description/message codes.
Signed-off-by: Laszlo Ast <laszlo.ast@siemens-enterprise.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add READ_16 + friends to scsi-defs.h, scsi_command_name() and the
request parsing helper functions.
Use them in scsi-disk.c too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move VERIFY emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move REPORT_LUNS emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add REPORT_LUNS to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move SERVICE_ACTION_IN emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add SERVICE_ACTION_IN to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move GET_CONFIGURATION emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add GET_CONFIGURATION to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move READ_TOC emulation from scsi_send_command() to
scsi_disk_emulate_command(). Add scsi_disk_emulate_read_toc() function
which holds the longisch READ_TOC emulation code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move SYNCHRONIZE_CACHE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move READ_CAPACITY emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move ALLOW_MEDIUM_REMOVAL emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move START_STOP emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move MODE_SENSE emulation from scsi_send_command() to
scsi_disk_emulate_command(). Create two helper functions:
mode_sense_page() which writes the actual mode pages and
scsi_disk_emulate_mode_sense() which holds the longish MODE_SENSE
emulation code, calling into mode_sense_page() as needed.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move RESERVE+RELEASE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move INQUIRY emulation from scsi_send_command() to
scsi_disk_emulate_command(). Also split the longish INQUITY emulation
code into the new scsi_disk_emulate_inquiry() function. Serial number
handling is slightly changed, we don't copy it any more but look it up
directly in DriveInfo which we have at hand anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move REQUEST_SENSE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add new scsi_disk_emulate_command() function, which will -- when
finished -- handle all scsi disk command emulation except actual I/O
(READ+WRITE commands) which goes to the block layer. The function
builds on top of the new SCSIRequest struct.
SCSI command emulation code is moved over from scsi_send_command() in
steps to ease review and make it easier to pin down regressions (if any)
using bisect. This patch moves over TEST_UNIT_READY only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Also add and use the scsi_req_complete() helper function for calling the
completion callback.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add helper functions for scsi request parsing to common code. Getting
command length, transfer size, and linear block address is handled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Largely based on <scsi/scsi.h> from linux. Added into the tree so we
can use the defines everywhere, not just in scsi-generic.c (which is
linux-specific).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Create generic functions to allocate, find and release SCSIRequest
structs. Make scsi-disk and scsi-generic use them.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
* Move from open-coded lists to QTAILQ macros.
* Move the struct elements to the common data structures
(SCSIDevice + SCSIRequest).
* Drop free request pools.
* Fix request cleanup in the destroy callback.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rename the SCSIRequest structs in scsi-disk.c and scsi-generic.c to
SCSIDiskReq and SCSIGenericReq. Create a SCSIRequest struct and move
the common elements over.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Also delete the leftover and unused scsi-disk.h file.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a NetClientInfo pointer to VLANClientState and use that
for the typecode and function pointers.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Nothing qdev specific about this, make it available throughtout.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since 1cc33683, this field is not set for most devices, so just
remove it and its remaining few uses.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Please, note that we will lose the "Try -device '?' for a list"
hint as it's qdev specific.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
With the recent device handling changes the I2C slave addressing code
was broken. With current code, if a slave with the correct address is
not found on the bus the last scanned slave on the bus will be
addressed. This is wrong. Please find attached a patch to fix it.
Signed-off-by: Juha Riihimäki <juha.riihimaki@nokia.com>
Acked-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the correct qdev property type for these devices.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
rtl8139.c is using malloc()/free() instead of qemu_malloc()/qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
xen_backend.c is using qemu_free() instead of free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
scsi-generic.c is using free() instead of qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
nseries.c is using free() instead of qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
bt-l2cap.c is using free() instead of qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
nand.c is using free() instead of qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
baum.c is using free() instead of qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
acpi.c is using free() instead of qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci code had a TODO to move apb specific
pci bridge initialization to apb_pci.
Implement this and remove the TODO.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Anthony Liguori's patch fixes the problems with
vga display in graphical mode and SeaBIOS.
I only adapted some values for vga-pci.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
PCI spec states:
if a masked vector has its Pending bit set, and the associated
underlying interrupt events are somehow satisfied (usually by software
though the exact manner is function-specific), the function must clear
the Pending bit, to avoid sending a spurious interrupt message later
when software unmasks the vector.
In our case this happens if vector becomes unused.
Clear pending bit in this case.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On reset, we currently clear all bits in msix control register *except*
enable bit. This is wrong: the spec says we should clear writeable
bits: function mask and enable bit.
Correct this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
msix state is managed by OS, not the
driver, so it's wrong to touch it
on io from driver.
Mark all vectors unused instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
goto into scope is evil. rearrange pci_bridge_filter
so that we always go to end of function on error.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
- fix bridge prefetchable memory accesser to check 64bit or not.
- use pcibus_t consistently instead mixing pcibus_t and uint64_t.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch replaces magic number, 256, with ARRAY_SIZE().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Split bar address math into a separate function.
In particular, this gets rid of an ugly forward goto
into scope that we have there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
This patch removes unused constants committed by
fb23162885.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch moves two typedefs, PCIHostState and PCIExpressHost to
qemu-common.h for consistency as PCIBus and PCIDevice are typedefed
in qemu-common.h.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch removes some comment which should go into commit log
in pci.h.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch replaces for loop by memset in pci_init_wmask().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
including pci_host.h isn't needed by pci.c.
This patch kills it.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch removes unnecessary & 0xff in pci_dev_find_by_addr().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch renames pci_find_host_bus() to pci_find_root_bus()
as suggested by "Michael S. Tsirkin" <mst@redhat.com>.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Because pci_sub_bus() is used only once so eliminate it
by open coding as suggested by "Michael S. Tsirkin" <mst@redhat.com>.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_host_data_register_io_memory and its variants are too long a bit.
So shorten them. Now they are
pci_host_{conf, data}_register_{mmio, mmio_noswap, ioport}()
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch renames pci_addr_to_dev(), pcie_mmcfg_addr_to_dev()
to pci_dev_find_by_addr(), pcie_dev_find_by_mmcfg_addr()
as "Michael S. Tsirkin" <mst@redhat.com> suggested.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch removes pci_addr_to_config() and open code it
as suggested by Michael S. Tsirkin <mst@redhat.com>.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove switch on length: we don't care about
high bits for value, so just return all ones
if no device. And add one assert().
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
Now pci host stuff has been moved from pci.[hc] to pci_host.[hc]
so the declaration of pci_data_{read, write}() should be in
pci_host.h
This patch moves them from pci.h to pci_host.h for consistency.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It printed wrong limit value of bridge.
This patch fixes it.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci.h declares some functions which aren't
defined in pci.h. Clean up moving things
to appropriate headers, and update all users.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This causes ctrl+alt+u or ctrl+alt+f to not work when windows hasn't been
resized first. Other graphic emulators do resize the screen on
hw_invalidate.
This reverts commit 0bd8246bfe.
Reqrite bitbanging I2C implementation. New code improves stop/start
condition handling, and gives more accurate input line level.
Introduce intermediate abstraction layer for I2C bitbanging that
is not connected via a GPIO port.
Signed-off-by: Paul Brook <paul@codesourcery.com>
We already have a working multiboot implementation that uses fw_cfg to get
its kernel module etc. data in int19 runtime now.
So what's missing is a working linux boot option rom. While at it I figured it
would be a good idea to take the opcode generator out of pc.c and instead use
a proper option rom, like we do with multiboot.
So here it is - an fw_cfg using option rom for -kernel with linux!
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Right now we load the guest kernel to RAM, fire off the BIOS, hope it
doesn't clobber memory and run an option rom that jumps into the kernel.
That breaks with SeaBIOS, as that clears memory. So let's read all
kernel, module etc. data using the fw_cfg interface when in the int19
handler.
This patch implements said mechanism for multiboot.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We have several rom helpers currently, but none of them can get us
code that spans several roms into a pointer.
This patch introduces a function that copies over rom contents.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch introduces block migration called during live migration. Block
are being copied to the destination in an async way. First the code will
transfer the whole disk and then transfer all dirty blocks accumulted during
the migration.
Still need to improve transition from the iterative phase of migration to the
end phase. For now transition will take place when all blocks transfered once,
all the dirty blocks will be transfered during the end phase (guest is
suspended).
Changes from v4:
- Global variabels moved to a global state structure allocated dynamically.
- Minor coding style issues.
- Poll block.c for tracking of dirty blocks instead of manage it here.
Signed-off-by: Liran Schour <lirans@il.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This function sends out the OPENED event to backends that
have drive the chardevs. The 'reset' is now a historical
artifact and we can now just call the function for what it
is.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Before 2e29bd0478, Uni-North host and AGP
bridge were using the same devfn, 11 << 3. The net effect was that only
AGP bridge was visible. This was changed in the commit to 13 << 3 for AGP.
Some of the later crashes happened due to NULL pointer dereferences generated
by 07b7d05377 and insufficient return value
checks.
Disable host device and revert AGP to 11 << 3.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Only two callers of pci_create_simple/pci_register_device bothered
to check the return value. Other cases were prone to crashing with
spurious NULL pointer dereferences.
Make QEMU exit with an error message when devfn is attempted to
be duplicated, also applies to case when the bus is full. Remove
checks.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Change 260c0cd3d9
(pci: use range helper functions) introduced a
bug which made pci cirrus vga on mips malta
(and maybe other pci devices) fail.
Don't change addr - its original value is needed
by ranges_overlap() and range_covers().
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Don't load the kernel twice during reset.
See f2d7497876.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Because of a typo, structure field vga_bios_size was not initialized
properly and a bogus BAR6 for the nonexistent VGA BIOS appeared.
The bug was uncovered by c169998802.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the user to specify the number of cores present on the
RealView EB + ARM11MPCore board. Also split into its own config
rather than guessing from the CPU name.
Signed-off-by: Paul Brook <paul@codesourcery.com>
When code was transformed to use qdev_reset/vmstate registration, vmstate
was passed a variable of the wrong type
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
While writing working on an e1000 driver for my university's OS I
noticed that some registers aren't readable in QEMU, but they should
be readable as stated in Intels Driver Developer Manual (and also
verified on real hardware).
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We need to signal not only write errors, but also read errors to the guest
driver. This fixes a regression introduced by 869a5c6d.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
A bus may have hotplugging enabled but not have the 'unplug'
callback defined, which would lead to a crash on trying to
unplug a device on the bus.
Fix by introducing an assert to check if the callback is valid.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some devices did not have an initialisation value
for entry ".exit". This is fixed here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* Rename pxe-eepro100.bin to pxe-i82559er.bin.
The other devices supported by eepro100.c need
additional pxe boot ROM images.
* Call rom_add_option during initialisation.
The code won't work with two or more different
eepro100 devices, because it only adds one option
ROM, but this use case is perhaps never needed.
Using this patch, model=i82559er at least works partially.
For full support, more eepro100 patches are needed
(will follow later, can be fetched from ar7 branch
of QEMU).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Many (most?) serial interfaces have a programmable
clock which provides the reference frequency ("baudbase").
So a fixed baudbase which is only set once can be wrong.
omap1.c is an example which could use the new interface
to change baudbase when the programmable clock changes.
ar7 system emulation (still not part of standard QEMU)
is similar to omap and already uses serial_set_frequency.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make MPCore secondary cpu initialization work with the new reset
handling. Also change the inital FLAG value from 3 to zero to match
recent kenrels.
Signed-off-by: Paul Brook <paul@codesourcery.com>
rom_+add_file/rom_add_blob only work correctly if called before
load_all_roms. Enforce this rather than silently accepting and putting
the rom in the wrong place at reset.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Since 45a50b1 load_image_targphys should only be called once.
ARM boards incorrectly call it every time the system is reset.
Signed-off-by: Paul Brook <paul@codesourcery.com>
* Add device properties (size of statistical data,
extended tcb support) to EEPRO100State and set
these values for the different devices.
* Fix PCI configuration for existing devices.
* Add initialisation code for missing devices.
* Remove function device_supports_eTxCB.
It is no longer needed.
* Fix dump of statistical data. It now respects
the real size of the statistical data.
An endianess issue was fixed here, too.
* CU_SHOWSTATS, CU_DUMPSTATS now write a
completion value after the statistical data.
There is no need to keep this value in
eepro100_stats_t, so member "complete"
could be removed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
make pci_info_device() print out bridge's filtering value like
io base/limit, subbus and subordinate bus.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch implements pci bridge filtering.
TODO: currently almost all the map funcions assumes
filtered_size == size and addr & ~(size - 1) == addr.
However with bridge filtering, they aren't always true.
Teach them such cases, such that filtered_size < size and
addr & (size - 1) != 0.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Liu Yu