This patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service
processor access to the internal buses of a host POWER processor to
perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage,
including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of
interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on buses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
The LBUS is modelled to maintain the qdev bus hierarchy and to take
advantage of the object model to automatically generate the CFAM
configuration block. The configuration block presents engines in the
order they are attached to the CFAM's LBUS. Engine implementations
should subclass the LBusDevice and set the 'config' member of
LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for
a CFAM to be simultaneously driven from multiple FSI links. The modeling
is not so complete; it's assumed that each CFAM is attached to a single
FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This
is not necessary to get FSI off the ground thanks to the mapping of the
CFAM address space onto the OPB address space - the models follow this
directly and map the CFAM memory region into the OPB's memory region.
Future work includes supporting more advanced accesses that drive the
FSI master directly rather than indirectly via the CFAM mapping, which
will require implementing the FSI state machine and methods for each of
the FSI symbols on the slave. Further down the track we can also look at
supporting the bitbanged SoftFSI drivers in Linux by extending the FSI
slave model to resolve sequences of GPIO IRQs into FSI symbols, and
calling the associated symbol method on the slave to map the access onto
the CFAM.
Testing:
Tested by reading cfam config address 0 on rainier machine type.
root@p10bmc:~# pdbg -a getcfam 0x0
p0: 0x0 = 0xc0022d15
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved FSIMasterState under AspeedAPB2OPBState
- modified fsi_opb_fsi_master_address() and
fsi_opb_opb2fsi_address()
- instroduced fsi_aspeed_apb2opb_init()
- reworked fsi_aspeed_apb2opb_realize()
- removed FSIMasterState object and fsi_opb_realize()
- simplified OPBus
- introduced fsi_aspeed_apb2opb_rw to fix endianness issue ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
This commit models the FSI master. CFAM is hanging out of FSI master which is a bus controller.
The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - move FSICFAMState object under FSIMasterState
- introduced fsi_master_init()
- reworked fsi_master_realize()
- dropped FSIBus definition ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on busses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c
- introduced fsi_cfam_instance_init()
- reworked fsi_cfam_realize() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where FSI bus is introduced.
The FSI bus is a simple bus where FSI master is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed include/hw/fsi/engine-scratchpad.h and
hw/fsi/engine-scratchpad.c
- dropped FSI_SCRATCHPAD
- included FSIBus definition
- dropped hw/fsi/trace-events changes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The scratchpad provides a set of non-functional registers. The firmware
is free to use them, hardware does not support any special management
support. The scratchpad registers can be read or written from LBUS
slave. The scratch pad is managed under FSI CFAM state.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The LBUS is modelled to maintain mapped memory for the devices. The
memory is mapped after CFAM config, peek table and FSI slave registers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed lbus_add_device() bc unused
- removed lbus_create_device() bc used only once
- removed "address" property
- updated meson.build to build fsi dir
- included an empty hw/fsi/trace-events ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Aspeed SoCs use a single CPU type (set as AspeedSoCClass::cpu_type).
Convert it to a NULL-terminated array (of a single non-NULL element).
Set MachineClass::valid_cpu_types[] to use the common machine code
to provide hints when the requested CPU is invalid (see commit
e702cbc19e ("machine: Improve is_cpu_type_supported()").
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to alter AspeedSoCClass::cpu_type in the next
commit, introduce the aspeed_soc_cpu_type() helper to
retrieve the per-SoC CPU type from AspeedSoCClass.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rework aspeed_soc_num_cpus() as a new init_cpus_defaults()
helper to reduce code duplication.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Since commit b7f1a0cb76 ("arm/aspeed: Compute the number
of CPUs from the SoC definition") Aspeed machines use the
aspeed_soc_num_cpus() helper to set the number of CPUs.
Use it for the ast1030-evb (commit 356b230ed1 "aspeed/soc:
Add AST1030 support") and supermicrox11-bmc (commit 40a38df55e
"hw/arm/aspeed: Add board model for Supermicro X11 BMC") machines.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Remove copy/paste typo from commit 6c323aba40 ("hw/arm/aspeed:
Adding new machine Tiogapass in QEMU").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
tcg/ should not depend on accel/tcg/, but perf and debuginfo
support provided by the latter are being used by tcg/tcg.c.
Since that's the only user, move both to tcg/.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231212003837.64090-5-iii@linux.ibm.com>
Message-Id: <20240125054631.78867-5-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When doing device assignment of a physical device, MSI-X can be
enabled with no vectors enabled and this sets the IRQ index to
VFIO_PCI_MSIX_IRQ_INDEX. However, when MSI-X is disabled, the IRQ
index is left untouched if no vectors are in use. Then, when INTx
is enabled, the IRQ index value is considered incompatible (set to
MSI-X) and VFIO_DEVICE_SET_IRQS fails. QEMU complains with :
qemu-system-x86_64: vfio 0000:08:00.0: Failed to set up TRIGGER eventfd signaling for interrupt INTX-0: VFIO_DEVICE_SET_IRQS failure: Invalid argument
To avoid that, unconditionaly clear the IRQ index when MSI-X is
disabled.
Buglink: https://issues.redhat.com/browse/RHEL-21293
Fixes: 5ebffa4e87 ("vfio/pci: use an invalid fd to enable MSI-X")
Cc: Jing Liu <jing2.liu@intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Do not use uint64_t for the type of the declaration and __u64 when
computing the number of elements in the array.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
- virtio-blk: Multiqueue fixes and cleanups
- blklogwrites: Fixes for write_zeroes and superblock update races
- commit/stream: Allow users to request only format driver names in
backing file format
- monitor: only run coroutine commands in qemu_aio_context
- Some iotest fixes
-----BEGIN PGP SIGNATURE-----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=KQJl
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://repo.or.cz/qemu/kevin into staging
Block layer patches
- virtio-blk: Multiqueue fixes and cleanups
- blklogwrites: Fixes for write_zeroes and superblock update races
- commit/stream: Allow users to request only format driver names in
backing file format
- monitor: only run coroutine commands in qemu_aio_context
- Some iotest fixes
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmWzpOwRHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9ZNzg//W1+C7HxLft4Jc4O1BcOoOLlGCg4Esupt
# z0/XLZ9+xVQUtjQ82pFzf9XaWQs8CuNT3FBUKi+ngdwZ0JBThIv0aGiMZBcAeQjD
# qshPFgDM1lGL4ICIaT73/qfUzQgO3oruZj9F+ShBBzoasNWVoRzqqVDR3pinLwTp
# D4TU+3A6LkdhlYGT60SYfRq/UKNmCA1s2wysdjqXxS6KOEURNF2VBnz0Nu76qrVb
# 3P/a55GPiJIn+VVsdQ0J4vyyzn23m7I7WZOJ7Sjm1EfSJ6SvcDbhWsZTUonaV2rU
# qZ3WI/jggqxXRV8F2AaA4suS/Cc8RkX2KfcN8fB6wDC2eI5USSatjh6xfw5xH9Ll
# NRKUO4vFFR3Lf8wN9apg0Bwxqi0GOm9kvBJT5QqjQ16R1dvqBLqbZqcx6ZXqWFXe
# /Iy243Tz19mWTFVUj0EgCKQpNz9F4SyXxV83HtSR1lJ5mhthnLxkvUOe7jsFPE4d
# 1Z3uBNWnx2mKFkhlwocMTKayYqxPuKQ+YjqrRoplLW1GZoBeoalKRGf8/RHa6kQx
# gh4cguihlb71AH1AO1QuYpiZt9G4RJR2RZlIoCPJY5TaKJedcxMVn8H+8/F0PnQd
# gPysZf7hTU1xCUV6TClDd+f2fuvqZYwXdwHJ9iiohNkbFq4HFQUp4nk4/eEPGSe/
# uv8oE813E30=
# =KQJl
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 26 Jan 2024 12:26:20 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin:
iotests/277: Use iotests.sock_dir for socket creation
iotests/iothreads-stream: Use the right TimeoutError
tests/unit: Bump test-replication timeout to 60 seconds
iotests/264: Use iotests.sock_dir for socket creation
block/blklogwrites: Protect mutable driver state with a mutex.
virtio-blk: always set ioeventfd during startup
virtio-blk: tolerate failure to set BlockBackend AioContext
virtio-blk: restart s->rq reqs in vq AioContexts
virtio-blk: rename dataplane to ioeventfd
virtio-blk: rename dataplane create/destroy functions
virtio-blk: move dataplane code into virtio-blk.c
monitor: only run coroutine commands in qemu_aio_context
iotests: port 141 to Python for reliable QMP testing
iotests: add filter_qmp_generated_node_ids()
stream: Allow users to request only format driver names in backing file format
commit: Allow users to request only format driver names in backing file format
string-output-visitor: Fix (pseudo) struct handling
block/blklogwrites: Fix a bug when logging "write zeroes" operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements a 32 half word FIFO as per imx serial device
specifications. If a non empty FIFO is below the trigger level, an
ageing timer will tick for a duration of 8 characters. On expiry,
AGTIM will be set triggering an interrupt. AGTIM timer resets when
there is activity in the receive FIFO.
Otherwise, RRDY is set when trigger level is exceeded. The receive
trigger level is 8 in newer kernel versions and 1 in older ones.
This change will break migration compatibility for the imx boards.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240125151931.83494-1-rayhan.faizel@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: commit message tidyups]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add MMDC, OCOTP, SQPI, CAAM, and USBMISC as unimplemented devices.
This allows operating systems such as Linux to run emulations such as
mcimx6ul-evk.
Before commit 0cd4926b85 ("Refactor i.MX6UL processor code"), the affected
memory ranges were covered by the unimplemented DAP device. The commit
reduced the DAP address range from 0x100000 to 4kB, and the emulation
thus no longer covered the various unimplemented devices in the affected
address range.
Fixes: 0cd4926b85 ("Refactor i.MX6UL processor code")
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240120005356.2599547-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Various files in hw/arm/ don't require "cpu.h" anymore.
Except virt-acpi-build.c, all of them don't require any
ARM specific knowledge anymore and can be build once as
target agnostic units. Update meson accordingly.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-21-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move Arm A-class Generic Timer definitions to the new
"target/arm/gtimer.h" header so units in hw/ which don't
need access to ARMCPU internals can use them without
having to include the huge "cpu.h".
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-20-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM_CPU_IRQ/FIQ definitions are used to index the GPIO
IRQ created calling qdev_init_gpio_in() in ARMCPU instance_init()
handler. To allow non-ARM code to raise interrupt on ARM cores,
move they to 'target/arm/cpu-qom.h' which is non-ARM specific and
can be included by any hw/ file.
File list to include the new header generated using:
$ git grep -wEl 'ARM_CPU_(\w*IRQ|FIQ)'
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-18-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now than we can access the M-profile bank index
definitions from the target-agnostic "cpu-qom.h"
header, we don't need the huge "cpu.h" anymore
(except in hw/arm/armv7m.c). Reduce its inclusion
to the source unit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-17-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/misc/xlnx-versal-crl.c doesn't require "cpu.h"
anymore. By removing it, the unit become target
agnostic: we can build it once. Update meson.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-15-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"target/arm/cpu.h" is target specific, any file including it
becomes target specific too, thus this is the same for any file
including "hw/misc/xlnx-versal-crl.h".
"hw/misc/xlnx-versal-crl.h" doesn't require any target specific
definition however, only the target-agnostic QOM definitions
from "target/arm/cpu-qom.h". Include the latter header to avoid
tainting unnecessary objects as target-specific.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-14-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/cpu/a9mpcore.c doesn't require "cpu.h" anymore.
By removing it, the unit become target agnostic:
we can build it once. Update meson.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-13-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Declare arm_cpu_mp_affinity() prototype in the new
"target/arm/multiprocessing.h" header so units in
hw/arm/ can use it without having to include the huge
target-specific "cpu.h".
File list to include the new header generated using:
$ git grep -lw arm_cpu_mp_affinity
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-11-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wrapper to return the mp affinity bits from the cpu.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename to arm_build_mp_affinity. This frees up the name for
other usage, and emphasizes that the cpu object is not involved.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/smmuv3-internal.h uses the REG32() and FIELD()
macros defined in "hw/registerfields.h". Include it in
order to avoid when refactoring unrelated headers:
In file included from ../../hw/arm/smmuv3.c:34:
hw/arm/smmuv3-internal.h:36:28: error: expected identifier
REG32(IDR0, 0x0)
^
hw/arm/smmuv3-internal.h:37:5: error: expected function body after function declarator
FIELD(IDR0, S2P, 0 , 1)
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/xilinx_zynq.c calls tswap32() which is declared
in "exec/tswap.h". Include it in order to avoid when
refactoring unrelated headers:
hw/arm/xilinx_zynq.c:103:31: error: call to undeclared function 'tswap32';
ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
board_setup_blob[n] = tswap32(board_setup_blob[n]);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/arm/exynos4210.c calls tswap32() which is declared
in "exec/tswap.h". Include it in order to avoid when
refactoring unrelated headers:
hw/arm/exynos4210.c:499:22: error: call to undeclared function 'tswap32';
ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
smpboot[n] = tswap32(smpboot[n]);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add watchdog timer support to Allwinner-H40 and Bananapi.
The watchdog timer is added as an overlay to the Timer
module memory map.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Message-id: 20240115182757.1095012-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports an AHCI compliant SATA controller.
Add support for it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240115182757.1095012-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports two USB host ports shared between a USB 2.0 EHCI
host controller and a USB 1.1 OHCI host controller. Add support for both
of them.
If machine USB support is not enabled, create unimplemented devices
for the USB memory ranges to avoid crashes when booting Linux.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240115182757.1095012-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TUSB6010 USB controller is soldered on the N800 and N810
tablets, thus is always present.
This is a migration compatibility break for the n800/n810
machines started with the '-usb none' option.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240119215106.45776-3-philmd@linaro.org
[PMM: fixed commit message typo]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The USB Controllers are part of the chipset, thus are
always present and mapped in memory.
This is a migration compatibility break for the cubieboard
machine started with the '-usb none' option.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240119215106.45776-2-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the musicpal key input device to use
qemu_add_kbd_event_handler(). This lets us simplify it because we no
longer need to track whether we're in the middle of a PS/2 multibyte
key sequence.
In the conversion we move the keyboard handler registration from init
to realize, because devices shouldn't disturb the state of the
simulation by doing things like registering input handlers until
they're realized, so that device objects can be introspected
safely.
The behaviour where key-repeat is permitted for the arrow-keys only
is intentional (added in commit 7c6ce4baed), so we retain it,
and add a comment to that effect.
This is a migration compatibility break for musicpal.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20231103182750.855577-1-peter.maydell@linaro.org
error_report() strings should not include trailing newlines; remove
the newline from the error we print when devices won't fit into the
address space of the CPU.
This commit also fixes the accidental hardcoded tabs that were in
this line, since we have to touch the line anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240118131649.2726375-1-peter.maydell@linaro.org
When starting ioeventfd it is common practice to set the event notifier
so that the ioeventfd handler is triggered to run immediately. There may
be no requests waiting to be processed, but the idea is that if a
request snuck in then we guarantee that it will be detected.
One scenario where self-triggering the ioeventfd is necessary is when
virtio_blk_handle_output() is called from a vCPU thread before the
VIRTIO Device Status transitions to DRIVER_OK. In that case we need to
self-trigger the ioeventfd so that the kick handled by the vCPU thread
causes the vq AioContext thread to take over handling the request(s).
Fixes: b6948ab01d ("virtio-blk: add iothread-vq-mapping parameter")
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-7-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We no longer rely on setting the AioContext since the block layer
IO_CODE APIs can be called from any thread. Now it's just a hint to help
block jobs and other operations co-locate themselves in a thread with
the guest I/O requests. Keep going if setting the AioContext fails.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-6-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A virtio-blk device with the iothread-vq-mapping parameter has
per-virtqueue AioContexts. It is not thread-safe to process s->rq
requests in the BlockBackend AioContext since that may be different from
the virtqueue's AioContext to which this request belongs. The code
currently races and could crash.
Adapt virtio_blk_dma_restart_cb() to first split s->rq into per-vq lists
and then schedule a BH each vq's AioContext as necessary. This way
requests are safely processed in their vq's AioContext.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-5-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The dataplane code is really about using ioeventfd. It's used both for
IOThreads (what we think of as dataplane) and for the core virtio-pci
code's ioeventfd feature (which is enabled by default and used when no
IOThread has been specified). Rename the code to reflect this.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-4-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
virtio_blk_data_plane_create() and virtio_blk_data_plane_destroy() are
actually about s->vq_aio_context[] rather than managing
dataplane-specific state.
As a prerequisite to using s->vq_aio_context[] in all code paths (even
when dataplane is not used), rename these functions to reflect that they
just manage s->vq_aio_context and call them regardless of whether or not
dataplane is in use.
Note that virtio-blk supports running with -device
virtio-blk-pci,ioevent=off where the vCPU thread enters the device
emulation code. In this mode ioeventfd is not used for virtqueue
processing. However, we still want to initialize s->vq_aio_context[] to
qemu_aio_context in that case since I/O completion callbacks will be
invoked in the main loop thread.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-3-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The dataplane code used to be significantly different from the
non-dataplane code and therefore had a separate source file.
Over time the difference has gotten smaller because the I/O code paths
were unified. Nowadays the distinction between the VirtIOBlock and
VirtIOBlockDataPlane structs is more of an inconvenience that hinders
code simplification.
Move hw/block/dataplane/virtio-blk.c into hw/block/virtio-blk.c, merging
VirtIOBlockDataPlane's fields into VirtIOBlock.
hw/block/virtio-blk.c used VirtIOBlock->dataplane to check if
virtio_blk_data_plane_create() was successful. This is not necessary
because ->dataplane_started and ->dataplane_disabled can be used
instead. This patch makes those changes in order to drop
VirtIOBlock->dataplane.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-2-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When HASH_REPORT is negotiated, the guest_hdr_len might be larger than
the size of the mergeable rx buffer header. Using
virtio_net_hdr_mrg_rxbuf during the header swap might lead a stack
overflow in this case. Fixing this by using virtio_net_hdr_v1_hash
instead.
Reported-by: Xiao Lei <leixiao.nop@zju.edu.cn>
Cc: Yuri Benditovich <yuri.benditovich@daynix.com>
Cc: qemu-stable@nongnu.org
Cc: Mauro Matteo Cascella <mcascell@redhat.com>
Fixes: CVE-2023-6693
Fixes: e22f0603fb ("virtio-net: reference implementation of hash report")
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Ninad Palsule