Add I2C model for AST2700 I2C support.
The I2C controller registers base address is start at
0x14C0_F000 and its address space is 0x2000.
The AST2700 I2C controller has one source INTC per bus.
I2C buses interrupt are connected to GICINT130_INTC
from bit 0 to bit 15.
I2C bus 0 is connected to GICINT130_INTC at bit 0.
I2C bus 15 is connected to GICINT130_INTC at bit 15.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Currently, users can set the INTC mapping table with
enumerated device id and device irq to get the INTC orgate
input pins. However, some devices use the continuous source numbers in the
same INTC orgate. To reduce the enumerated device id definition,
create a new API to get the INTC orgate input pin
if users only provide the device id with its bus number index.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35)
and the base address of dram is "0x4 00000000" which
is 64bits address.
The AST2700 support the maximum DRAM size is 8 GB.
The DRAM physical address range is from "0x4_0000_0000" to
"0x5_FFFF_FFFF".
The DRAM offset range is from "0x0_0000_0000" to
"0x1_FFFF_FFFF" and it is enough to use bits [33:0]
saving the dram offset.
Therefore, save the high part physical address bit[1:0]
of Tx/Rx buffer address as dma_dram_offset bit[33:32].
It does not need to decrease the dram physical
high part address for DMA operation.
(high part physical address bit[7:0] – 4)
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35)
and the base address of dram is "0x4 00000000" which
is 64bits address.
It has "Master DMA Mode Tx Buffer Base Address[39:32](0x60)"
and "Master DMA Mode Rx Buffer Base Address[39:32](0x64)"
registers to save the high part physical address of Tx/Rx
buffer address for master mode.
It has "Slave DMA Mode Tx Buffer Base Address[39:32](0x68)" and
"Slave DMA Mode Rx Buffer Base Address[39:32](0x6C)" registers
to save the high part physical address of Tx/Rx buffer address
for slave mode.
Ex: Tx buffer address for master mode [39:0]
The "Master DMA Mode Tx Buffer Base Address[39:32](0x60)"
bits [7:0] which corresponds the bits [39:32] of the 64 bits address of
the Tx buffer address.
The "Master DMA Mode Tx Buffer Base Address(0x30)" bits [31:0]
which corresponds the bits [31:0] of the 64 bits address
of the Tx buffer address.
Introduce a new has_dma64 class attribute and new registers for the
new mode to support DMA 64 bits dram address.
Update new mode register number to 28.
The aspeed_i2c_bus_vmstate is changed again and
version is not increased because it was done earlier in the same series.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Introduce a new ast2700 class to support AST2700.
The I2C bus register memory regions and
I2C bus pool buffer memory regions are discontinuous
and they do not back compatible AST2600.
Add a new ast2700 i2c class init function to match the
address of I2C bus register and pool buffer from the datasheet.
An I2C controller registers owns 8KB address space.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
The "Current DMA Operating Address Status(0x50)" register of
I2C new mode has been removed in AST2700.
This register is used for debugging and it is a read only register.
To support AST2700 DMA mode, introduce a new
dma_dram_offset class attribute in AspeedI2Cbus to save the
current DMA operating address.
ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35)
And the base address of dram is "0x4 00000000" which
is 64bits address.
Set the dma_dram_offset data type to uint64_t for
64 bits dram address DMA support.
Both "DMA Mode Buffer Address Register(I2CD24 old mode)" and
"DMA Operating Address Status (I2CC50 new mode)" are used for showing the
low part dram offset bits [31:0], so change to read/write both register bits [31:0] in
bus register read/write functions.
The aspeed_i2c_bus_vmstate is changed again and version is not increased
because it was done earlier in the same series.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
It only support continuous pool buffer memory region for all I2C bus.
However, the pool buffer address of all I2c bus are discontinuous
for AST2700.
Ex: the pool buffer address of I2C bus for ast2700 as following.
0x1A0 - 0x1BF: Device 0 buffer
0x2A0 - 0x2BF: Device 1 buffer
0x3A0 - 0x3BF: Device 2 buffer
0x4A0 - 0x4BF: Device 3 buffer
0x5A0 - 0x5BF: Device 4 buffer
0x6A0 - 0x6BF: Device 5 buffer
0x7A0 - 0x7BF: Device 6 buffer
0x8A0 - 0x8BF: Device 7 buffer
0x9A0 - 0x9BF: Device 8 buffer
0xAA0 - 0xABF: Device 9 buffer
0xBA0 - 0xBBF: Device 10 buffer
0xCA0 - 0xCBF: Device 11 buffer
0xDA0 - 0xDBF: Device 12 buffer
0xEA0 - 0xEBF: Device 13 buffer
0xFA0 – 0xFBF: Device 14 buffer
0x10A0 – 0x10BF: Device 15 buffer
Introduce a new class attribute to make user set each I2C bus
pool buffer gap size. Update formula to create all I2C bus
pool buffer memory regions.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
According to the datasheet of ASPEED SOCs,
each I2C bus has their own pool buffer since AST2500.
Only AST2400 utilized a pool buffer share to all I2C bus.
Besides, using a share pool buffer only support
pool buffer memory regions are continuous for all I2C bus.
To make this model more readable and support discontinuous
bus pool buffer memory regions, changes to introduce
a new bus pool buffer attribute in AspeedI2Cbus and
new memops. So, it does not need to calculate
the pool buffer offset for different I2C bus.
Introduce a new has_share_pool class attribute in AspeedI2CClass and
use it to create either a share pool buffer or bus pool buffers
in aspeed_i2c_realize. Update each pull buffer size to 0x10 for AST2500
and 0x20 for AST2600 and AST1030.
Incrementing the version of aspeed_i2c_bus_vmstate to 6.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
It only support continuous register memory region for all I2C bus.
However, the register address of all I2c bus are discontinuous
for AST2700.
Ex: the register address of I2C bus for ast2700 as following.
0x100 - 0x17F: Device 0
0x200 - 0x27F: Device 1
0x300 - 0x37F: Device 2
0x400 - 0x47F: Device 3
0x500 - 0x57F: Device 4
0x600 - 0x67F: Device 5
0x700 - 0x77F: Device 6
0x800 - 0x87F: Device 7
0x900 - 0x97F: Device 8
0xA00 - 0xA7F: Device 9
0xB00 - 0xB7F: Device 10
0xC00 - 0xC7F: Device 11
0xD00 - 0xD7F: Device 12
0xE00 - 0xE7F: Device 13
0xF00 – 0xF7F: Device 14
0x1000 – 0x107F: Device 15
Introduce a new class attribute to make user set each I2C bus gap size.
Update formula to create all I2C bus register memory regions.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
In aspeed_gpio_update() we calculate "mask = 1 << gpio", where
gpio can be between 0 and 31. Coverity complains about this
because 1 << 31 won't fit in a signed integer.
For QEMU this isn't an error because we enable -fwrapv,
but we can keep Coverity happy by doing the shift on
unsigned numbers.
Resolves: Coverity CID 1547742
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Use of assert(false) can trip spurious control flow warnings from
some versions of GCC (i.e. using -fsanitize=thread with gcc-12):
error: control reaches end of non-void function [-Werror=return-type]
default:
g_assert_not_reached();
break;
| ^^^^^
Solve that by removing the unreachable 'break' statement, unifying
the code base on g_assert_not_reached() instead.
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240910221606.1817478-31-pierrick.bouvier@linaro.org>
[PMD: Add description suggested by Eric Blake]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Use of assert(false) can trip spurious control flow warnings from
some versions of GCC (i.e. using -fsanitize=thread with gcc-12):
error: control reaches end of non-void function [-Werror=return-type]
default:
g_assert_not_reached();
break;
| ^^^^^
Solve that by removing the unreachable 'break' statement, unifying
the code base on g_assert_not_reached() instead.
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240910221606.1817478-29-pierrick.bouvier@linaro.org>
[PMD: Add description suggested by Eric Blake]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Use of assert(false) can trip spurious control flow warnings from
some versions of GCC (i.e. using -fsanitize=thread with gcc-12):
error: control reaches end of non-void function [-Werror=return-type]
default:
g_assert_not_reached();
break;
| ^^^^^
Solve that by removing the unreachable 'break' statement, unifying
the code base on g_assert_not_reached() instead.
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240910221606.1817478-28-pierrick.bouvier@linaro.org>
[PMD: Add description suggested by Eric Blake]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Use of assert(false) can trip spurious control flow warnings from
some versions of GCC (i.e. using -fsanitize=thread with gcc-12):
error: control reaches end of non-void function [-Werror=return-type]
default:
assert(0);
| }
| ^
Solve that by unifying the code base on g_assert_not_reached() instead.
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Message-ID: <20240910221606.1817478-8-pierrick.bouvier@linaro.org>
[PMD: Add description suggested by Eric Blake]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Use of assert(false) can trip spurious control flow warnings from
some versions of GCC (i.e. using -fsanitize=thread with gcc-12):
error: control reaches end of non-void function [-Werror=return-type]
default:
assert(0);
| }
| ^
Solve that by unifying the code base on g_assert_not_reached() instead.
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240910221606.1817478-6-pierrick.bouvier@linaro.org>
[PMD: Add description suggested by Eric Blake]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Use of assert(false) can trip spurious control flow warnings from
some versions of GCC (i.e. using -fsanitize=thread with gcc-12):
error: control reaches end of non-void function [-Werror=return-type]
default:
assert(0);
| }
| ^
Solve that by unifying the code base on g_assert_not_reached() instead.
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240910221606.1817478-5-pierrick.bouvier@linaro.org>
[PMD: Add description suggested by Eric Blake]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Update the ADB mouse implementation to use QemuInputHandler instead of the
legacy qemu_add_mouse_event_handler() function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240907173700.348818-1-mark.cave-ayland@ilande.co.uk>
[PMD: Add comment about .sync handler]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Update the Sun mouse implementation to use QemuInputHandler instead of the
legacy qemu_add_mouse_event_handler() function.
Note that this conversion adds extra sunmouse_* members to ESCCChannelState
but they are not added to the migration stream (similar to the Sun keyboard
members). If this were desired in future, the Sun devices should be split
into separate devices and added to the migration stream there instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2518
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Carl Hauser <chauser@pullman.com>
Message-ID: <20240904102301.175706-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Per datasheet, "HIGH AND LOW LIMIT REGISTERS", the lower 4 bit
of the limit registers are unused and always report 0.
The lower 4 bit should not be used for temperature comparisons,
so mask the unused bits before storing the limits.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20240906154911.86803-6-philmd@linaro.org>
[PMD: Update tests/qtest/ files]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Per datasheet, "ONE-SHOT (OS)", the OS bit always returns 0 when reading
the configuration register.
Clear the ONE_SHOT bit in the WRITE path. Now than the READ path is
simpler, we can also simplify tmp105_alarm_update().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20240906154911.86803-5-philmd@linaro.org>
The next commit will clear the ONE_SHOT bit in the WRITE
path (to keep the READ path trivial). As a preliminary step,
pass the 'oneshot' value as argument to tmp105_alarm_update().
No logical change intended.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <20240906154911.86803-4-philmd@linaro.org>
To improve readability, use the registerfields API.
Define the register bits with FIELD(), and use the
FIELD_EX8() and FIELD_DP8() macros. Remove the
abbreviations in comments.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <20240906154911.86803-3-philmd@linaro.org>
Coding style asks for no space between variable and "++". The next patch
in this series will change one of those assignments. Instead of changing
just one with that patch, change all of them for consistency.
While at it, also fix other coding style problems reported by checkpatch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20240906154911.86803-2-philmd@linaro.org>
In preparation of having a TX FIFO, rename the RX FIFO methods.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240719181041.49545-12-philmd@linaro.org>
We shouldn't transmit characters when the full UART or its
transmitter is disabled. However we don't want to break the
possibly incomplete "my first bare metal assembly program"s,
so we choose to simply display a warning when this occurs.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240719181041.49545-9-philmd@linaro.org>
To keep MemoryRegionOps read/write handlers with similar logic,
factor pl011_read_txdata() out of pl011_read(), similar to what
the previous commit did to pl011_write().
No functional change intended.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240719181041.49545-8-philmd@linaro.org>
When implementing FIFO, this code will become more complex.
Start by factoring it out to a new pl011_write_txdata() function.
No functional change intended.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240719181041.49545-7-philmd@linaro.org>
To be able to reset the RX or TX FIFO separately,
split pl011_reset_fifo() in two.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240719181041.49545-6-philmd@linaro.org>
We'll soon use pl011_loopback_enabled() and pl011_loopback_tx()
from functions defined before their declarations. In order to
avoid forward-declaring them, move them around.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240719181041.49545-5-philmd@linaro.org>
Avoid forward-declaring pl011_put_fifo() by moving it earlier.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240719181041.49545-4-philmd@linaro.org>
Since its introduction in commit cdbdb648b7 ("ARM Versatile
Platform Baseboard emulation.") PL011State::readbuff as never
been used. Remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240719181041.49545-3-philmd@linaro.org>
We just removed the single machine using it (axis-dev88).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-12-philmd@linaro.org>
We just removed the single machine calling etraxfs_dmac_init()
(the axis-dev88 machine).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-11-philmd@linaro.org>
We just removed the single machine using it (axis-dev88).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-10-philmd@linaro.org>
We just removed the single machine using it (axis-dev88).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-9-philmd@linaro.org>
We just removed the single machine using it (axis-dev88).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-8-philmd@linaro.org>
No more CRIS machine uses cris_load_image(), remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-7-philmd@linaro.org>
This machine was deprecated for the v9.0 release in commit
c7bbef4023 ("docs: mark CRIS support as deprecated").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-ID: <20240904143603.52934-6-philmd@linaro.org>
sh7750_register_io_device() was only used by the TC58128
NAND EEPROM which has been removed in the previous commit.
Remove it as unused code.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Message-ID: <20240903153959.18392-4-philmd@linaro.org>
The TC58128 NAND EEPROM is not user creatable and
needs to be instanciated in the code via tc58128_init().
Only the SHIX machine was using it, and it was removed
in the previous commit. Since the TC58128 has no more
users, remove it too.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20240903153959.18392-3-philmd@linaro.org>
The SHIX machine is deprecated since v9.0 (commit
322b038c94 "target/sh4: Deprecate the shix machine").
Time to remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Message-ID: <20240903153959.18392-2-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240718133312.10324-19-philmd@linaro.org>
designware_pcie_root_realize() uses get_system_memory()
as the "host side memory region", as opposed to the "PCI
side" one. Introduce the 'host_mem' variable for clarity.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Gustavo Romero <gustavo.romero@linaro.org>
Message-Id: <20231012121857.31873-4-philmd@linaro.org>
When multiple QOM types are registered in the same file,
it is simpler to use the the DEFINE_TYPES() macro. In
particular because type array declared with such macro
are easier to review.
Remove a pointless structure declaration in "designware.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Gustavo Romero <gustavo.romero@linaro.org>
Message-Id: <20231012121857.31873-2-philmd@linaro.org>
On GICv2 and later, level triggered interrupts are pending when either
the interrupt line is asserted or the interrupt was made pending by a
GICD_ISPENDRn write. Making a level triggered interrupt pending by
software persists until either the interrupt is acknowledged or cleared
by writing GICD_ICPENDRn. As long as the interrupt line is asserted,
the interrupt is pending in any case.
This logic is transparently implemented in gic_test_pending() for
GICv1 and GICv2. The function combines the "pending" irq_state flag
(used for edge triggered interrupts and software requests) and the
line status (tracked in the "level" field). However, we also
incorrectly set the pending flag on a guest write to GICD_ISENABLERn
if the line of a level triggered interrupt was asserted. This keeps
the interrupt pending even if the line is de-asserted after some
time.
This incorrect logic is a leftover of the initial 11MPCore GIC
implementation. That handles things slightly differently to the
architected GICv1 and GICv2. The 11MPCore TRM does not give a lot of
detail on the corner cases of its GIC's behaviour, and historically
we have not wanted to investigate exactly what it does in reality, so
QEMU's GIC model takes the approach of "retain our existing behaviour
for 11MPCore, and implement the architectural standard for later GIC
revisions".
On that basis, commit 8d999995e4 in 2013 is where we added the
"level-triggered interrupt with the line asserted" handling to
gic_test_pending(), and we deliberately kept the old behaviour of
gic_test_pending() for REV_11MPCORE. That commit should have added
the "only if 11MPCore" condition to the setting of the pending bit on
writes to GICD_ISENABLERn, but forgot it.
Add the missing "if REV_11MPCORE" condition, so that our behaviour
on GICv1 and GICv2 matches the GIC architecture requirements.
Cc: qemu-stable@nongnu.org
Fixes: 8d999995e4 ("arm_gic: Fix GIC pending behavior")
Signed-off-by: Jan Klötzke <jan.kloetzke@kernkonzept.com>
Message-id: 20240911114826.3558302-1-jan.kloetzke@kernkonzept.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: expanded comment a little and converted to coding-style form;
expanded commit message with the historical backstory]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The read index should not be changed when storing a new message into the
RX or TX FIFO. Changing it at this point will cause the reader to get
out of sync. The wrapping of the read index is already handled by the
pre-write functions for the FIFO status registers anyway.
Additionally, the calculation for wrapping the store index was off by
one, which caused new messages to be written to the wrong location in
the FIFO. This caused incorrect messages to be delivered.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20240827034927.66659-8-doug@schmorgal.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use QEMU's helper functions can_dlc2len() and can_len2dlc() for
translating between the raw DLC value and the SocketCAN length value.
This also has the side effect of correctly handling received CAN FD
frames with a DLC of 0-8, which was broken previously.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20240827034927.66659-7-doug@schmorgal.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The endianness of the CAN data was backwards in each group of 4 bytes.
For example, the following data:
00 11 22 33 44 55 66 77
was showing up like this:
33 22 11 00 77 66 55 44
Fix both the TX and RX code to put the data in the correct order.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-id: 20240827034927.66659-6-doug@schmorgal.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for QEMU_CAN_FRMF_ESI and QEMU_CAN_FRMF_BRS flags, and
ensure frame->flags is always initialized to 0.
Note that the Xilinx IP core doesn't allow manually setting the ESI bit
during transmits, so it's only implemented for the receive case.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-id: 20240827034927.66659-5-doug@schmorgal.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Previously the emulated CAN ID register was being set to the exact same
value stored in qemu_can_frame.can_id. This doesn't work correctly
because the Xilinx IP core uses a different bit arrangement than
qemu_can_frame for all of its ID registers. Correct this problem for
both RX and TX, including RX filtering.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-id: 20240827034927.66659-4-doug@schmorgal.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When checking the QEMU_CAN_FRMF_TYPE_FD flag, we need to ignore other
potentially set flags. Before this change, received CAN FD frames from
SocketCAN weren't being recognized as CAN FD.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20240827034927.66659-3-doug@schmorgal.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The interrupt level should be 0 or 1. The existing code was using the
interrupt flags to determine the level. In the only machine currently
supported (xlnx-versal-virt), the GICv3 was masking off all bits except
bit 0 when applying it, resulting in the IRQ never being delivered.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-id: 20240827034927.66659-2-doug@schmorgal.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch's main focus is to use the previously added
hvf_get_physical_address_range to inform VM creation
about the IPA size we need for the VM, so we can extend
the default 36b IPA size and support VMs with 64+GB of
RAM. This is done by freezing the memory map, computing
the highest GPA and then (depending on if the platform
supports an IPA size that large) telling the kernel to
use a size >= for the VM. In pursuit of this a couple of
things related to how we handle the physical address range
we expose to guests were altered, but for an explanation of
what we were doing:
Today, to get the IPA size we were reading id_aa64mmfr0_el1's
PARange field from a newly made vcpu. Unfortunately, HVF just
returns the hosts PARange directly for the initial value and
not the IPA size that will actually back the VM, so we believe
we have much more address space than we actually do today it seems.
Starting in macOS 13.0 some APIs were introduced to be able to
query the maximum IPA size the kernel supports, and to set the IPA
size for a given VM. However, this still has a couple of issues
on < macOS 15. Up until macOS 15 (and if the hardware supported
it) the max IPA size was 39 bits which is not a valid PARange
value, so we can't clamp down what we advertise in the vcpu's
id_aa64mmfr0_el1 to our IPA size. Starting in macOS 15 however,
the maximum IPA size is 40 bits (if it's supported in the hardware
as well) which is also a valid PARange value so we can set our IPA
size to the maximum as well as clamp down the PARange we advertise
to the guest. This allows VMs with 64+ GB of RAM and should fix the
oddness of the PARange situation as well.
Signed-off-by: Danny Canter <danny_canter@apple.com>
Message-id: 20240828111552.93482-4-danny_canter@apple.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This addition will be necessary for some HVF related work to follow.
For HVF on ARM there exists a set of APIs in macOS 13 to be able to
adjust the IPA size for a given VM. This is useful as by default HVF
uses 36 bits as the IPA size, so to support guests with > 64GB of RAM
we'll need to reach for this.
To have all the info necessary to carry this out however, we need some
plumbing to be able to grab the memory map and compute the highest GPA
prior to creating the VM. This is almost exactly like what kvm_type is
used for on ARM today, and is also what this will be used for. We will
compute the highest GPA and find what IPA size we'd need to satisfy this,
and if it's valid (macOS today caps at 40b) we'll set this to be the IPA
size in coming patches. This new method is only needed (today at least)
on ARM, and obviously only for HVF/macOS, so admittedly it is much less
generic than kvm_type today, but it seemed a somewhat sane way to get
the information we need from the memmap at VM creation time.
Signed-off-by: Danny Canter <danny_canter@apple.com>
Message-id: 20240828111552.93482-2-danny_canter@apple.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: removed explicit setting of field to NULL on x86]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We used to need the transitional_function machinery to handle bus
classes and device classes which still used their legacy reset
handling. We have now converted all bus classes to three phase
reset, and simplified the device class legacy reset so it is just an
adapting wrapper function around registration of a hold phase method.
There are therefore no more users of the transitional_function
machinery and we can remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240830145812.1967042-12-peter.maydell@linaro.org
Now that all devices which still implement a the legacy reset method
register it via device_class_legacy_reset(), we can simplify the
handling of these devices. Instead of using the complex
Resettable::get_transitional_function machinery, we register a hold
phase method which invokes the DeviceClass::legacy_reset method.
This will allow us to remove all the get_transitional_function
handling from resettable.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240830145812.1967042-11-peter.maydell@linaro.org
Currently we have transitional machinery between legacy reset
and three phase reset that works in two directions:
* if you invoke three phase reset on a device which has set
the DeviceClass::legacy_reset method, we detect this in
device_get_transitional_reset() and arrange that we call
the legacy_reset method during the hold phase of reset
* if you invoke legacy reset on a device which implements
three phase reset, the default legacy_reset method is
device_phases_reset(), which does a three-phase reset
of the device
However, we have now eliminated all the places which could invoke
legacy reset on a device, which means that the function
device_phases_reset() is never called -- it serves only as the value
of DeviceClass::legacy_reset that indicates that the subclass never
overrode the legacy reset method. So we can delete it, and instead
check for legacy_reset != NULL.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-10-peter.maydell@linaro.org
Rename the DeviceClass::reset field to legacy_reset; this is helpful
both in flagging up that it's best not used in new code and in
making it easy to search for where it's being used still.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-9-peter.maydell@linaro.org
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
Define a device_class_set_legacy_reset() function which
sets the DeviceClass::reset field. This serves two purposes:
* it makes it clearer to the person writing code that
DeviceClass::reset is now legacy and they should look for
the new alternative (which is Resettable)
* it makes it easier to rename the reset field (which in turn
makes it easier to find places that call it)
The Coccinelle script can be used to automatically convert code that
was doing an open-coded assignment to DeviceClass::reset to call
device_class_set_legacy_reset() instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-7-peter.maydell@linaro.org
There are no callers of device_class_set_parent_reset() left in the tree,
as they've all been converted to use three-phase reset and the
corresponding resettable_class_set_parent_phases() function.
Remove device_class_set_parent_reset().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-5-peter.maydell@linaro.org
Convert the virtio-ccw code to three-phase reset. This allows us to
remove a call to device_class_set_parent_reset(), replacing it with
the three-phase equivalent resettable_class_set_parent_phases().
Removing all the device_class_set_parent_reset() uses will allow us
to remove some of the glue code that interworks between three-phase
and legacy reset.
This is a simple conversion, with no behavioural changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-3-peter.maydell@linaro.org
Convert the TYPE_CCW_DEVICE to three-phase reset. This is a
device class which is subclassed, so it needs to be three-phase
before we can convert the subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20240830145812.1967042-2-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZuLmLgAKCRBAov/yOSY+
38JNA/9UdorT4a7H+H5PhNeEu2EHDgMPb7+gxyYKw03mOG2MB3KFzkK0LRQShaPt
ADJmIqAFlc9SJLkbo6ELMDl+ZnUU9OdC/P6YU5iBG71zx1PonMwuyJTWhlBwxWcG
+OB8aDBUALoe/Gb4za152I84cR08g58TgLnXNfEkCM8lnPfAug==
=Plwu
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20240912' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20240912
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZuLmLgAKCRBAov/yOSY+
# 38JNA/9UdorT4a7H+H5PhNeEu2EHDgMPb7+gxyYKw03mOG2MB3KFzkK0LRQShaPt
# ADJmIqAFlc9SJLkbo6ELMDl+ZnUU9OdC/P6YU5iBG71zx1PonMwuyJTWhlBwxWcG
# +OB8aDBUALoe/Gb4za152I84cR08g58TgLnXNfEkCM8lnPfAug==
# =Plwu
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 12 Sep 2024 14:01:34 BST
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20240912' of https://gitlab.com/gaosong/qemu:
hw/loongarch: Add acpi SPCR table support
hw/loongarch: virt: pass random seed to fdt
hw/loongarch: virt: support up to 4 serial ports
target/loongarch: Support QMP dump-guest-memory
target/loongarch/kvm: Add vCPU reset function
hw/loongarch: Remove default enable with VIRTIO_VGA device
target/loongarch: Add compatible support about VM reboot
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
i286 acpi speedup by precomputing _PRT by Ricardo Ribalda
vhost_net speedup by using MR transactions by Zuo Boqun
ich9 gained support for periodic and swsmi timer by Dominic Prinz
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmbhoCUPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRptpUH/iR5AmJFpvAItqlPOvJiYDEch46C73tyrSws
Kk/1EbGSL7mFFD5sfdSSV4Rw8CQBsmM/Dt5VDkJKsWnOLjkBQ2CYH0MYHktnrKcJ
LlSk32HnY5p1DsXnJhgm5M7St8T3mV/oFdJCJAFgCmpx5uT8IRLrKETN8+30OaiY
xo35xAKOAS296+xsWeVubKkMq7H4y2tdZLE/22gb8rlA8d96BJIeVLQ3y3IjeUPR
24q6c7zpObzGhYNZ/PzAKOn+YcVsV/lLAzKRZJTzTUPyG24BcjJTyyr/zNSYAgfk
lLXzIZID3GThBmrCAiDZ1z6sfo3MRg2wNS/FBXtK6fPIuFxed+8=
=ySRy
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, fixes, cleanups
i286 acpi speedup by precomputing _PRT by Ricardo Ribalda
vhost_net speedup by using MR transactions by Zuo Boqun
ich9 gained support for periodic and swsmi timer by Dominic Prinz
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmbhoCUPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRptpUH/iR5AmJFpvAItqlPOvJiYDEch46C73tyrSws
# Kk/1EbGSL7mFFD5sfdSSV4Rw8CQBsmM/Dt5VDkJKsWnOLjkBQ2CYH0MYHktnrKcJ
# LlSk32HnY5p1DsXnJhgm5M7St8T3mV/oFdJCJAFgCmpx5uT8IRLrKETN8+30OaiY
# xo35xAKOAS296+xsWeVubKkMq7H4y2tdZLE/22gb8rlA8d96BJIeVLQ3y3IjeUPR
# 24q6c7zpObzGhYNZ/PzAKOn+YcVsV/lLAzKRZJTzTUPyG24BcjJTyyr/zNSYAgfk
# lLXzIZID3GThBmrCAiDZ1z6sfo3MRg2wNS/FBXtK6fPIuFxed+8=
# =ySRy
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 11 Sep 2024 14:50:29 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu:
hw/acpi/ich9: Add periodic and swsmi timer
virtio-mem: don't warn about THP sizes on a kernel without THP support
hw/audio/virtio-sound: fix heap buffer overflow
hw/cxl: fix physical address field in get scan media results output
virtio-pci: Add lookup subregion of VirtIOPCIRegion MR
vhost_net: configure all host notifiers in a single MR transaction
tests/acpi: pc: update golden masters for DSDT
hw/i386/acpi-build: Return a pre-computed _PRT table
tests/acpi: pc: allow DSDT acpi table changes
intel_iommu: Make PASID-cache and PIOTLB type invalid in legacy mode
intel_iommu: Fix invalidation descriptor type field
virtio: rename virtio_split_packed_update_used_idx
hw/pci/pci-hmp-cmds: Avoid displaying bogus size in 'info pci'
pci: don't skip function 0 occupancy verification for devfn auto assign
hw/isa/vt82c686.c: Embed i8259 irq in device state instead of allocating
hw: Move declaration of IRQState to header and add init function
virtio: Always reset vhost devices
virtio: Allow .get_vhost() without vhost_started
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Serial port console redirection table can be used for default serial
port selection, like chosen stdout-path selection with FDT method.
With acpi SPCR table added, early debug console can be parsed from
SPCR table with simple kernel parameter earlycon rather than
earlycon=uart,mmio,0x1fe001e0
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240907073037.243353-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
If the FDT contains /chosen/rng-seed, then the Linux RNG will use it to
initialize early. Set this using the usual guest random number
generation function.
This is the same procedure that's done in b91b6b5a2c ("hw/microblaze:
pass random seed to fdt"), e4b4f0b71c ("hw/riscv: virt: pass random seed
to fdt"), c6fe3e6b4c ("hw/openrisc: virt: pass random seed to fdt"),
67f7e426e5 ("hw/i386: pass RNG seed via setup_data entry"), c287941a4d
("hw/rx: pass random seed to fdt"), 5e19cc68fb ("hw/mips: boston: pass
random seed to fdt"), 6b23a67916 ("hw/nios2: virt: pass random seed to fdt")
c4b075318e ("hw/ppc: pass random seed to fdt"), and 5242876f37
("hw/arm/virt: dt: add rng-seed property").
These earlier commits later were amended to rerandomize the RNG seed on
snapshot load, but the LoongArch code somehow already does that, despite
not having this patch here, presumably due to some lucky copy and
pasting.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240905153316.2038769-1-Jason@zx2c4.com>
Signed-off-by: Song Gao <gaosong@loongson.cn>
In order to support additional channels of communication using
`-serial`, add several serial ports, up to the standard 4 generally
supported by the 8250 driver.
Fixed: https://lore.kernel.org/all/20240907143439.2792924-1-Jason@zx2c4.com/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Bibo Mao <maobibo@loongson.cn>
[gaosong: ACPI uart need't reverse order]
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240907143439.2792924-1-Jason@zx2c4.com>
For virtio VGA deivce libvirt will select VIRTIO_VGA firstly rather than
VIRTIO_GPU, VIRTIO_VGA device supports frame buffer however it requires
legacy VGA compatible support. Frame buffer area 0xa0000 -- 0xc0000
conflicts with low memory area 0 -- 0x10000000.
Here remove default support for VIRTIO_VGA device, VIRTIO_GPU is prefered
on LoongArch system. For frame buffer video card support, standard VGA can
be used.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240823073050.2619484-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
This patch implements the periodic and the swsmi ICH9 chipset timers. They are
especially useful when prototyping UEFI firmware (e.g. with EDK2's OVMF)
using QEMU.
For backwards compatibility, the compat properties "x-smi-swsmi-timer",
and "x-smi-periodic-timer" are introduced.
Additionally, writes to the SMI_STS register are enabled for the
corresponding two bits using a write mask to make future work easier.
Signed-off-by: Dominic Prinz <git@dprinz.de>
Message-Id: <1d90ea69e01ab71a0f2ced116801dc78e04f4448.1725991505.git.git@dprinz.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the config directory in sysfs does not exist at all, we are dealing
with a system that does not support THPs. Simply use 1 MiB block size
then, instead of warning "Could not detect THP size, falling back to
..." and falling back to the default THP size.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Gavin Shan <gshan@redhat.com>
Cc: Juraj Marcin <jmarcin@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240910163433.2100295-1-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the guest may write to the device configuration space,
whereas the virtio sound device specification in chapter 5.14.4
clearly states that the fields in the device configuration space
are driver-read-only.
Remove the set_config function from the virtio_snd class.
This also prevents a heap buffer overflow. See QEMU issue #2296.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2296
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20240901130112.8242-1-vr_qemu@t-online.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When using the mailbox command get scan media results, the scan media
restart physical address field in the ouput palyload is not 64-byte
aligned.
This patch removed the error source of the restart physical address.
The Scan Media Restart Physical Address is the location from which the
host should restart the Scan Media operation. [5:0] bits are reserved.
Refer to CXL spec r3.1 Table 8-146
Fixes: 89b5cfcc31 ("hw/cxl: Add get scan media results cmd support")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/linux-cxl/20240819154206.16456-1-engguopeng@buaa.edu.cn/
Signed-off-by: peng guo <engguopeng@buaa.edu.cn>
Message-Id: <20240825102212.3871-1-engguopeng@buaa.edu.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now virtio_address_space_lookup only lookup common/isr/device/notify
MR and exclude their subregions.
When VHOST_USER_PROTOCOL_F_HOST_NOTIFIER enable, the notify MR has
host-notifier subregions and we need use host-notifier MR to
notify the hardware accelerator directly instead of eventfd notify.
Further more, maybe common/isr/device MR also has subregions in
the future, so need memory_region_find for each MR incluing
their subregions.
Add lookup subregion of VirtIOPCIRegion MR instead of only lookup container MR.
Fixes: a93c8d8 ("virtio-pci: Replace modern_as with direct access to modern_bar")
Co-developed-by: Zuo Boqun <zuoboqun@baidu.com>
Signed-off-by: Gao Shiyuan <gaoshiyuan@baidu.com>
Signed-off-by: Zuo Boqun <zuoboqun@baidu.com>
Message-Id: <20240903120304.97833-1-gaoshiyuan@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows the vhost_net device which has multiple virtqueues to batch
the setup of all its host notifiers. This significantly reduces the
vhost_net device starting and stoping time, e.g. the time spend
on enabling notifiers reduce from 630ms to 75ms and the time spend on
disabling notifiers reduce from 441ms to 45ms for a VM with 192 vCPUs
and 15 vhost-user-net devices (64vq per device) in our case.
Signed-off-by: zuoboqun <zuoboqun@baidu.com>
Message-Id: <20240816070835.8309-1-zuoboqun@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When qemu runs without kvm acceleration the ACPI executions take a great
amount of time. If they take more than the default time (30sec), the
ACPI calls fail and the system might not behave correctly.
Now the _PRT table is computed on the fly. We can drastically reduce the
execution of the _PRT method if we return a pre-computed table.
Without this patch:
[ 51.343484] ACPI Error: Aborting method \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/psparse-529)
[ 51.527032] ACPI Error: Method execution failed \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/uteval-68)
[ 51.530049] virtio-pci 0000:00:02.0: can't derive routing for PCI INT A
[ 51.530797] virtio-pci 0000:00:02.0: PCI INT A: no GSI
[ 81.922901] ACPI Error: Aborting method \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/psparse-529)
[ 82.103534] ACPI Error: Method execution failed \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/uteval-68)
[ 82.106088] virtio-pci 0000:00:04.0: can't derive routing for PCI INT A
[ 82.106761] virtio-pci 0000:00:04.0: PCI INT A: no GSI
[ 112.192568] ACPI Error: Aborting method \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/psparse-529)
[ 112.486687] ACPI Error: Method execution failed \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/uteval-68)
[ 112.489554] virtio-pci 0000:00:05.0: can't derive routing for PCI INT A
[ 112.490027] virtio-pci 0000:00:05.0: PCI INT A: no GSI
[ 142.559448] ACPI Error: Aborting method \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/psparse-529)
[ 142.718596] ACPI Error: Method execution failed \_SB.PCI0._PRT due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/uteval-68)
[ 142.722889] virtio-pci 0000:00:06.0: can't derive routing for PCI INT A
[ 142.724578] virtio-pci 0000:00:06.0: PCI INT A: no GSI
With this patch:
[ 22.938076] ACPI: \_SB_.LNKB: Enabled at IRQ 10
[ 24.214002] ACPI: \_SB_.LNKD: Enabled at IRQ 11
[ 25.465170] ACPI: \_SB_.LNKA: Enabled at IRQ 10
[ 27.944920] ACPI: \_SB_.LNKC: Enabled at IRQ 11
ACPI disassembly:
Scope (PCI0)
{
Method (_PRT, 0, NotSerialized) // _PRT: PCI Routing Table
{
Return (Package (0x80)
{
Package (0x04)
{
0xFFFF,
Zero,
LNKD,
Zero
},
Package (0x04)
{
0xFFFF,
One,
LNKA,
Zero
},
Package (0x04)
{
0xFFFF,
0x02,
LNKB,
Zero
},
Package (0x04)
{
0xFFFF,
0x03,
LNKC,
Zero
},
Package (0x04)
{
0x0001FFFF,
Zero,
LNKS,
Zero
},
Context: https://lore.kernel.org/virtualization/20240417145544.38d7b482@imammedo.users.ipa.redhat.com/T/#t
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240814115736.1580337-3-ribalda@chromium.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In vtd_process_inv_desc(), VTD_INV_DESC_PC and VTD_INV_DESC_PIOTLB are
bypassed without scalable mode check. These two types are not valid
in legacy mode and we should report error.
Fixes: 4a4f219e8a ("intel_iommu: add scalable-mode option to make scalable mode work")
Suggested-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Clément Mathieu--Drif<clement.mathieu--drif@eviden.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Message-Id: <20240814071321.2621384-3-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to spec, invalidation descriptor type is 7bits which is
concatenation of bits[11:9] and bits[3:0] of invalidation descriptor.
Currently we only pick bits[3:0] as the invalidation type and treat
bits[11:9] as reserved zero. This is not a problem for now as bits[11:9]
is zero for all current invalidation types. But it will break if newer
type occupies bits[11:9].
Fix it by taking bits[11:9] into type and make reserved bits check accurate.
Suggested-by: Clément Mathieu--Drif<clement.mathieu--drif@eviden.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Reviewed-by: Clément Mathieu--Drif<clement.mathieu--drif@eviden.com>
Message-Id: <20240814071321.2621384-2-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio_split_packed_update_used_idx should be
virtio_queue_split_update_used_idx like
virtio_split_packed_update_used_idx.
Signed-off-by: Wenyu Huang <huangwenyuu@outlook.com>
Message-Id: <TYBP286MB036536B9015994AA5F3E4495ACB22@TYBP286MB0365.JPNP286.PROD.OUTLOOK.COM>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When BAR aren't mapped, we get:
(qemu) info pci
Bus 0, device 0, function 0:
Host bridge: PCI device dead:beef
...
BAR4: 32 bit memory at 0xffffffffffffffff [0x00000ffe].
BAR5: I/O at 0xffffffffffffffff [0x0ffe].
Check the BAR is mapped comparing its address to PCI_BAR_UNMAPPED
which is what the PCI layer uses for unmapped BARs.
See pci_bar_address and pci_update_mappings implementations and
in "hw/pci/pci.h":
typedef struct PCIIORegion {
pcibus_t addr; /* current PCI mapping address. -1 means not mapped */
#define PCI_BAR_UNMAPPED (~(pcibus_t)0)
...
This improves the logging, not displaying bogus sizes:
(qemu) info pci
Bus 0, device 0, function 0:
Host bridge: PCI device dead:beef
...
BAR4: 32 bit memory (not mapped)
BAR5: I/O (not mapped)
Remove trailing dot which is not used in other commands format.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240801131449.51328-1-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the devfn is already assigned in the command line, the
do_pci_register_device() may verify if the function 0 is already occupied.
However, when devfn < 0, the verification is skipped because it is part of
the last "else if".
For instance, suppose there is already a device at addr=00.00 of a port.
-device pcie-root-port,bus=pcie.0,chassis=115,id=port01,addr=0e.00 \
-device virtio-net-pci,bus=port01,id=vnet01,addr=00.00 \
When 'addr' is specified for the 2nd device, the hotplug is denied.
(qemu) device_add virtio-net-pci,bus=port01,id=vnet02,addr=01.00
Error: PCI: slot 0 function 0 already occupied by virtio-net-pci, new func virtio-net-pci cannot be exposed to guest.
When 'addr' is automatically assigned, the hotplug is not denied. This is
because the verification is skipped.
(qemu) device_add virtio-net-pci,bus=port01,id=vnet02
warning: PCI: slot 1 is not valid for virtio-net-pci, parent device only allows plugging into slot 0.
Fix the issue by moving the verification into an independent 'if'
statement.
Fixes: 3f1e1478db ("enable multi-function hot-add")
Reported-by: Aswin Unnikrishnan <aswin.u.unnikrishnan@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Message-Id: <20240708041056.54504-1-dongli.zhang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid a warning about unfreed qemu_irq embed the i8259 irq in the
device state instead of allocating it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <b70b9e72063b4dd4005bf4bc040b84f2bb617bf4.1719690591.git.balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
To allow embedding a qemu_irq in a struct move its definition to the
header and add a function to init it in place without allocating it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <e3ffd0f6ef8845d0f7247c9b6ff33f7ee8b432cf.1719690591.git.balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Requiring `vhost_started` to be true for resetting vhost devices in
`virtio_reset()` seems like the wrong condition: Most importantly, the
preceding `virtio_set_status(vdev, 0)` call will (for vhost devices) end
up in `vhost_dev_stop()` (through vhost devices' `.set_status`
implementations), setting `vdev->vhost_started = false`. Therefore, the
gated `vhost_reset_device()` call is unreachable.
`vhost_started` is not documented, so it is hard to say what exactly it
is supposed to mean, but judging from the fact that `vhost_dev_start()`
sets it and `vhost_dev_stop()` clears it, it seems like it indicates
whether there is a vhost back-end, and whether that back-end is
currently running and processing virtio requests.
Making a reset conditional on whether the vhost back-end is processing
virtio requests seems wrong; in fact, it is probably better to reset it
only when it is not currently processing requests, which is exactly the
current order of operations in `virtio_reset()`: First, the back-end is
stopped through `virtio_set_status(vdev, 0)`, then we want to send a
reset.
Therefore, we should drop the `vhost_started` condition, but in its
stead we then have to verify that we can indeed send a reset to this
vhost device, by not just checking `k->get_vhost != NULL` (introduced by
commit 95e1019a4a), but also that the vhost back-end is connected
(`hdev = k->get_vhost(); hdev != NULL && hdev->vhost_ops != NULL`).
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-Id: <20240723163941.48775-3-hreitz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Historically, .get_vhost() was probably only called when
vdev->vhost_started is true. However, we now decidedly want to call it
also when vhost_started is false, specifically so we can issue a reset
to the vhost back-end while device operation is stopped.
Some .get_vhost() implementations dereference some pointers (or return
offsets from them) that are probably guaranteed to be non-NULL when
vhost_started is true, but not necessarily otherwise. This patch makes
all such implementations check all such pointers, returning NULL if any
is NULL.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-Id: <20240723163941.48775-2-hreitz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
QAPI's 'prefix' feature can make the connection between enumeration
type and its constants less than obvious. It's best used with
restraint.
VfioMigrationState has a 'prefix' that overrides the generated
enumeration constants' prefix to QAPI_VFIO_MIGRATION_STATE.
We could simply drop 'prefix', but then the enumeration constants
would look as if they came from kernel header linux/vfio.h.
Rename the type to QapiVfioMigrationState instead, so that 'prefix' is
not needed.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240904111836.3273842-20-armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
QAPI's 'prefix' feature can make the connection between enumeration
type and its constants less than obvious. It's best used with
restraint.
QCryptodevBackendAlgType has a 'prefix' that overrides the generated
enumeration constants' prefix to QCRYPTODEV_BACKEND_ALG.
We could simply drop 'prefix', but I think the abbreviation "alg" is
less than clear.
Additionally rename the type to QCryptodevBackendAlgoType. The prefix
becomes QCRYPTODEV_BACKEND_ALGO_TYPE.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240904111836.3273842-19-armbru@redhat.com>
QAPI's 'prefix' feature can make the connection between enumeration
type and its constants less than obvious. It's best used with
restraint.
QCryptodevBackendServiceType has a 'prefix' that overrides the
generated enumeration constants' prefix to QCRYPTODEV_BACKEND_SERVICE.
Drop it. The prefix becomes QCRYPTODEV_BACKEND_SERVICE_TYPE.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240904111836.3273842-18-armbru@redhat.com>
QAPI's 'prefix' feature can make the connection between enumeration
type and its constants less than obvious. It's best used with
restraint.
QCryptoHashAlgorithm has a 'prefix' that overrides the generated
enumeration constants' prefix to QCRYPTO_HASH_ALG.
We could simply drop 'prefix', but then the prefix becomes
QCRYPTO_HASH_ALGORITHM, which is rather long.
We could additionally rename the type to QCryptoHashAlg, but I think
the abbreviation "alg" is less than clear.
Rename the type to QCryptoHashAlgo instead. The prefix becomes to
QCRYPTO_HASH_ALGO.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240904111836.3273842-12-armbru@redhat.com>
[Conflicts with merge commit 7bbadc60b5 resolved]
QAPI's 'prefix' feature can make the connection between enumeration
type and its constants less than obvious. It's best used with
restraint.
CpuS390Entitlement has a 'prefix' to change the generated enumeration
constants' prefix from CPU_S390_ENTITLEMENT to S390_CPU_ENTITLEMENT.
Rename the type to S390CpuEntitlement, so that 'prefix' is not needed.
Likewise change CpuS390Polarization to S390CpuPolarization, and
CpuS390State to S390CpuState.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240904111836.3273842-10-armbru@redhat.com>
Recent commit "qapi: Smarter camel_to_upper() to reduce need for
'prefix'" added a temporary 'prefix' to delay changing the generated
code.
Revert it. This improves HmatLBDataType's generated enumeration
constant prefix from HMATLB_DATA_TYPE to HMAT_LB_DATA_TYPE, and
HmatLBMemoryHierarchy's from HMATLB_MEMORY_HIERARCHY to
HMAT_LB_MEMORY_HIERARCHY.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240904111836.3273842-8-armbru@redhat.com>
Recent commit "qapi: Smarter camel_to_upper() to reduce need for
'prefix'" added a temporary 'prefix' to delay changing the generated
code.
Revert it. This improves OffAutoPCIBAR's generated enumeration
constant prefix from OFF_AUTOPCIBAR to OFF_AUTO_PCIBAR.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20240904111836.3273842-5-armbru@redhat.com>
Adds support for 'qatzip' as an option for the multifd compression
method parameter, and implements using QAT for 'qatzip' compression and
decompression.
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Prasad Pandit <pjp@fedoraproject.org>
Signed-off-by: Bryan Zhang <bryan.zhang@bytedance.com>
Signed-off-by: Hao Xiang <hao.xiang@linux.dev>
Signed-off-by: Yichen Wang <yichen.wang@bytedance.com>
Link: https://lore.kernel.org/r/20240830232722.58272-5-yichen.wang@bytedance.com
Signed-off-by: Peter Xu <peterx@redhat.com>
When DMA memory can't be directly accessed, as is the case when
running the device model in a separate process without shareable DMA
file descriptors, bounce buffering is used.
It is not uncommon for device models to request mapping of several DMA
regions at the same time. Examples include:
* net devices, e.g. when transmitting a packet that is split across
several TX descriptors (observed with igb)
* USB host controllers, when handling a packet with multiple data TRBs
(observed with xhci)
Previously, qemu only provided a single bounce buffer per AddressSpace
and would fail DMA map requests while the buffer was already in use. In
turn, this would cause DMA failures that ultimately manifest as hardware
errors from the guest perspective.
This change allocates DMA bounce buffers dynamically instead of
supporting only a single buffer. Thus, multiple DMA mappings work
correctly also when RAM can't be mmap()-ed.
The total bounce buffer allocation size is limited individually for each
AddressSpace. The default limit is 4096 bytes, matching the previous
maximum buffer size. A new x-max-bounce-buffer-size parameter is
provided to configure the limit for PCI devices.
Signed-off-by: Mattias Nissler <mnissler@rivosinc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240819135455.2957406-1-mnissler@rivosinc.com
Signed-off-by: Peter Xu <peterx@redhat.com>
The TYPE_NUBUS_DEVICE class lets the user specify the nubus slot
using an int32 "slot" QOM property. Its realize method doesn't do
any range checking on this value, which Coverity notices by way of
the possibility that 'nd->slot * NUBUS_SUPER_SLOT_SIZE' might
overflow the 32-bit arithmetic it is using.
Constrain the slot value to be less than NUBUS_SLOT_NB (16).
Resolves: Coverity CID 1464070
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20240830173452.2086140-4-peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The datasheets for the SoC and board we model here are still
available from the NXP website; add their URLs and titles for
future reference.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-ID: <20240830173452.2086140-3-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
In m5208_sys_read(), we have a loop of n from 0 to 31, and we
calculate (2u << n). For the n == 31 iteration this will shift off
the top of the unsigned 32 bit integer.
This is harmless, because we're going to stop the loop with n == 31
anyway, but we can avoid the error by using 64-bit arithmetic here.
(The SDCS0 register is documented at
https://www.nxp.com/docs/en/reference-manual/MCF5208RM.pdf
section 18.4.5; we want the lower 5 bits to indicate the
RAM size, where 31 == 4GB, 30 == 2GB, and so on down.
As it happens, the layout of the mcf5208evb board memory map
means it doesn't make sense to have more than 1GB of RAM
in any case.)
Resolves: Coverity CID 1547727
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-ID: <20240830173452.2086140-2-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Minor bugs and errors related to ufs-test are resolved. Some
permissions and code implementations that are not synchronized
with the ufs spec are edited.
Signed-off-by: Yoochan Jeong <yc01.jeong@samsung.com>
Reviewed-by: Jeuk Kim <jeuk20.kim@samsung.com>
Signed-off-by: Jeuk Kim <jeuk20.kim@samsung.com>
Modify to fill the opcode, idn, index, selector information of
all Query Response UPIU. because attr and flag operation of query
response upiu need these information too.
Signed-off-by: KyoungrulKim <k831.kim@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im@samsung.com>
Reviewed-by: Jeuk Kim <jeuk20.kim@samsung.com>
Signed-off-by: Jeuk Kim <jeuk20.kim@samsung.com>
memory_region_find() returns an MR which it is the caller's
responsibility to unref, but platform_bus_map_mmio() was
forgetting to do so, thus leaking the MR.
Signed-off-by: Gao Shiyuan <gaoshiyuan@baidu.com>
Message-id: 20240829131005.9196-1-gaoshiyuan@baidu.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the file is not an ELF file, arm_setup_direct_kernel_boot()
falls back to try it as a uimage or an AArch64 Image file or as
last resort a bare raw binary. We can discard load_elf_hdr()
error and silently return.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240903144154.17135-1-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Print errors before exit. Do not exit silently.
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Changbin Du <changbin.du@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240903133940.3447430-1-changbin.du@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The system supports the Security Extensions (core and GIC). This change is
necessary to run tests which pass on the real hardware.
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-id: 20240828005019.57705-1-sebastian.huber@embedded-brains.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In sbsa_fdt_add_gic_node() we g_strdup_printf() two nodename
strings, but only free one.
Since the string is actually entirely constant and we don't
make any use of printf's format-string operations, we can
drop the g_strdup_printf() use entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240822162323.706382-1-peter.maydell@linaro.org
The TYPE_XLNX_VERSAL_EFUSE_CTRL device creates a register block with
register_init_block32() in its instance_init method; we must
therefore destroy it in our instance_finalize method to avoid a leak
in the QOM introspection "init-inspect-finalize" lifecycle:
Direct leak of 304 byte(s) in 1 object(s) allocated from:
#0 0x55f222b5b9d8 in __interceptor_calloc (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-aarch64+0x294e9d8) (BuildId: 420
43d49e1139e3f3071b1f22fac1e3e7249c9a6)
#1 0x7fbb10669c50 in g_malloc0 debian/build/deb/../../../glib/gmem.c:161:13
#2 0x55f222f90c5d in register_init_block hw/core/register.c:248:34
#3 0x55f222f916be in register_init_block32 hw/core/register.c:299:12
#4 0x55f223bbdd15 in efuse_ctrl_init hw/nvram/xlnx-versal-efuse-ctrl.c:718:9
#5 0x55f225b23391 in object_init_with_type qom/object.c:420:9
#6 0x55f225b0a66b in object_initialize_with_type qom/object.c:562:5
#7 0x55f225b0bf0d in object_new_with_type qom/object.c:782:5
#8 0x55f225b0bfe1 in object_new qom/object.c:797:12
#9 0x55f226309e0d in qmp_device_list_properties qom/qom-qmp-cmds.c:144:11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240822162127.705879-7-peter.maydell@linaro.org
The TYPE_XLNX_VERSAL_TRNG device creates a register block with
register_init_block32() in its instance_init method; we must
therefore destroy it in our instance_finalize method to avoid a leak
in the QOM introspection "init-inspect-finalize" lifecycle:
Direct leak of 304 byte(s) in 1 object(s) allocated from:
#0 0x55842ec799d8 in __interceptor_calloc (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-aarch64+0x294e9d8) (BuildId: 47496e53f3e779f1c7e9b82cbea07407152b498b)
#1 0x7fe793c75c50 in g_malloc0 debian/build/deb/../../../glib/gmem.c:161:13
#2 0x55842f0aec5d in register_init_block hw/core/register.c:248:34
#3 0x55842f0af6be in register_init_block32 hw/core/register.c:299:12
#4 0x55842f801588 in trng_init hw/misc/xlnx-versal-trng.c:614:9
#5 0x558431c411a1 in object_init_with_type qom/object.c:420:9
#6 0x558431c2847b in object_initialize_with_type qom/object.c:562:5
#7 0x558431c29d1d in object_new_with_type qom/object.c:782:5
#8 0x558431c29df1 in object_new qom/object.c:797:12
#9 0x558432427c1d in qmp_device_list_properties qom/qom-qmp-cmds.c:144:11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240822162127.705879-6-peter.maydell@linaro.org
The TYPE_XLNX_ZYNQMP_EFUSE device creates a register block with
register_init_block32() in its instance_init method; we must
therefore destroy it in our instance_finalize method to avoid a leak
in the QOM introspection "init-inspect-finalize" lifecycle:
Direct leak of 304 byte(s) in 1 object(s) allocated from:
#0 0x55f3ff5839d8 in __interceptor_calloc (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-aarch64+0x294d9d8) (BuildId: 23cf931c66865a71b6cc4da95156d03bc106fa72)
#1 0x7f3f31c6bc50 in g_malloc0 debian/build/deb/../../../glib/gmem.c:161:13
#2 0x55f3ff9b8c5d in register_init_block hw/core/register.c:248:34
#3 0x55f3ff9b96be in register_init_block32 hw/core/register.c:299:12
#4 0x55f4005e5b25 in efuse_ctrl_init hw/nvram/xlnx-versal-efuse-ctrl.c:718:9
#5 0x55f40254afb1 in object_init_with_type qom/object.c:420:9
#6 0x55f40253228b in object_initialize_with_type qom/object.c:562:5
#7 0x55f402533b2d in object_new_with_type qom/object.c:782:5
#8 0x55f402533c01 in object_new qom/object.c:797:12
#9 0x55f402d31a2d in qmp_device_list_properties qom/qom-qmp-cmds.c:144:11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240822162127.705879-5-peter.maydell@linaro.org
The TYPE_XLNX_BBRAM device creates a register block with
register_init_block32() in its instance_init method; we must
therefore destroy it in our instance_finalize method to avoid a leak
in the QOM introspection "init-inspect-finalize" lifecycle:
Direct leak of 304 byte(s) in 1 object(s) allocated from:
#0 0x5641518ca9d8 in __interceptor_calloc (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-aarch64+0x294d9d8) (BuildId: 4a6
18cb63d57d5a19ed45cfc262b08da47eaafe5)
#1 0x7ff1aab31c50 in g_malloc0 debian/build/deb/../../../glib/gmem.c:161:13
#2 0x564151cffc5d in register_init_block hw/core/register.c:248:34
#3 0x564151d006be in register_init_block32 hw/core/register.c:299:12
#4 0x56415293df75 in bbram_ctrl_init hw/nvram/xlnx-bbram.c:462:9
#5 0x564154891dc1 in object_init_with_type qom/object.c:420:9
#6 0x56415487909b in object_initialize_with_type qom/object.c:562:5
#7 0x56415487a93d in object_new_with_type qom/object.c:782:5
#8 0x56415487aa11 in object_new qom/object.c:797:12
#9 0x56415507883d in qmp_device_list_properties qom/qom-qmp-cmds.c:144:11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240822162127.705879-4-peter.maydell@linaro.org
The TYPE_XLNX_VERSAL_TRNG device creates s->prng with g_rand_new()
in its init method, but it frees it in its unrealize method. This
results in a leak in the QOM introspection "initialize-inspect-finalize"
lifecycle:
Direct leak of 2500 byte(s) in 1 object(s) allocated from:
#0 0x55ec89eae9d8 in __interceptor_calloc (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-aarch64+0x294d9d8) (BuildId: 6d5
08874816cc47d17c8dd775e8f809ae520e8cb)
#1 0x7f697018fc50 in g_malloc0 debian/build/deb/../../../glib/gmem.c:161:13
#2 0x7f6970197738 in g_rand_new_with_seed_array debian/build/deb/../../../glib/grand.c:202:17
#3 0x7f6970197816 in g_rand_new debian/build/deb/../../../glib/grand.c:286:10
#4 0x55ec8aa3656a in trng_init hw/misc/xlnx-versal-trng.c:624:15
#5 0x55ec8ce75da1 in object_init_with_type qom/object.c:420:9
#6 0x55ec8ce5d07b in object_initialize_with_type qom/object.c:562:5
#7 0x55ec8ce5e91d in object_new_with_type qom/object.c:782:5
#8 0x55ec8ce5e9f1 in object_new qom/object.c:797:12
#9 0x55ec8d65c81d in qmp_device_list_properties qom/qom-qmp-cmds.c:144:11
Move the free to finalize so it matches where we are initing
s->prng. Since that's the only thing our unrealize method was
doing, this essentially switches the whole function to be
a finalize implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240822162127.705879-3-peter.maydell@linaro.org
Since the TYPE_XNLX_VERSAL_CFU_FDRO device creates a FIFO in its
instance_init method, we must destroy the FIFO in instance_finalize
to avoid a memory leak for the QOM introspection
"instantiate-examine-finalize" cycle:
Direct leak of 8192 byte(s) in 1 object(s) allocated from:
#0 0x55ec89eae7ee in malloc (/mnt/nvmedisk/linaro/qemu-from-laptop/qemu/build/asan/qemu-system-aarch64+0x294d7ee) (BuildId: 6d508874816cc47d17c8dd775e8f809ae520e8cb)
#1 0x7f697018f738 in g_malloc debian/build/deb/../../../glib/gmem.c:128:13
#2 0x55ec8d98d98d in fifo8_create util/fifo8.c:27:18
#3 0x55ec8aa2a624 in fifo32_create /mnt/nvmedisk/linaro/qemu-from-laptop/qemu/include/qemu/fifo32.h:35:5
#4 0x55ec8aa2a33c in cfu_fdro_init hw/misc/xlnx-versal-cfu.c:397:5
#5 0x55ec8ce75da1 in object_init_with_type qom/object.c:420:9
#6 0x55ec8ce5d07b in object_initialize_with_type qom/object.c:562:5
#7 0x55ec8ce5e91d in object_new_with_type qom/object.c:782:5
#8 0x55ec8ce5e9f1 in object_new qom/object.c:797:12
#9 0x55ec8d65c81d in qmp_device_list_properties qom/qom-qmp-cmds.c:144:11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240822162127.705879-2-peter.maydell@linaro.org
Now that our SMMU model supports enabling both stages of translation
at once, we can enable this in the sbsa-ref board. Existing guest
code that only programs stage 1 and doesn't care about stage 2 should
continue to run with the same behaviour, but guests that do want to
do nested SMMU configurations can now do so.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20240816161350.3706332-5-peter.maydell@linaro.org
Now that our SMMU model supports enabling both stages of translation
at once, we can enable this in the virt board. This is no change in
behaviour for guests, because if they simply ignore stage 2 and never
configure it then it has no effect. For the usual backwards
compatibility reasons we enable this only for machine types starting
with 9.2.
(Note that the SMMU is disabled by default on the virt board and is
only created if the user passes the 'iommu=smmuv3' machine option.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20240816161350.3706332-4-peter.maydell@linaro.org
When we added support for nested (stage 1 + stage 2) translation
to the SMMU in commit 58377c3632 we forgot to update the
comment that documents the valid values of the "stage" property.
Add the new "nested" value to it.
Fixes: 58377c3632 ("hw/arm/smmuv3: Support and advertise nesting")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20240816161350.3706332-3-peter.maydell@linaro.org
Add a Xen PVH x86 machine based on the abstract PVH Machine.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Add support for optionally creating a PCIe/GPEX controller.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
We've been creating the virtio-mmio devices in forwards order
but since the qbus lists prepend (rather than append) entries,
the virtio busses end up with decreasing base address order.
Xen enables virtio-mmio nodes in forwards order so there's been
a missmatch. So far, we've been working around this with an
out-of-tree patch to Xen.
This reverses the order making sure the virtio busses end up
ordered with increasing base addresses avoiding the need to
patch Xen.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Rename xen_arm.c -> xen-pvh.c to better express that this
is a PVH machine and to align with x86 HVM and future PVH
machine filenames:
hw/i386/xen/xen-hvm.c
hw/i386/xen/xen-pvh.c (in preparation)
No functional changes.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Break out a common Xen PVH machine in preparation for
adding a x86 Xen PVH machine.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Add SMP support for Xen PVH ARM guests.
Create ms->smp.max_cpus ioreq servers to handle hotplug.
Note that ms->smp.max_cpus will be passed to us by the
user (Xen tools) set to the guests maxvcpus.
The value in mc->max_cpus is an absolute maximum for the
-smp option and won't be used to setup ioreq servers unless
the user explicitly specifies it with -smp.
If the user doesn't pass -smp on the command-line, smp.cpus
and smp.max_cpus will default to 1.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Tweak machine description to better express that this is
a Xen PVH machine for ARM.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Update file header to use SPDX and remove stray empty
comment line.
No functional changes.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Cosmetic: add comments in x86_load_linux() pointing to the kernel documentation
so that users can better understand the code.
CC: qemu-trivial@nongnu.org
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
3 small patches to make sure we don't ship regressions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmbEdw8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp0dsIAKTzhmBR3IviFQVo223RgcDfthxoKejTB5tv
EhGVUi4ddrViIIHsKFZ0pTHXnRcwHpPRokg6GrbqNhrAM6K7ptP8pkEK1DDkbGtq
HaeceK55nNZ/wM1O5xHpRLVc2WtxmBrliDTFHGB2HjURO/kpjoHqWbE6Sn4GILc1
EYU2T3Wn1UFgj+H4L7yF4SzmQSmyzq+7Tml6Z2GzpsatdwCoFQz2nA28piCnRMCq
lusMo2YdE6js9JS/h+zMqgKValuCyuU7S7ZbSO2dvYQwt/hgk07BegBrdsAENNh6
0IWRHrojwAg+4U6ULzbrBG6/hW2A8Q5065D8Nf9Bjy4eAU7QSbU=
=K6xx
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio: regression fixes
3 small patches to make sure we don't ship regressions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmbEdw8PHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp0dsIAKTzhmBR3IviFQVo223RgcDfthxoKejTB5tv
# EhGVUi4ddrViIIHsKFZ0pTHXnRcwHpPRokg6GrbqNhrAM6K7ptP8pkEK1DDkbGtq
# HaeceK55nNZ/wM1O5xHpRLVc2WtxmBrliDTFHGB2HjURO/kpjoHqWbE6Sn4GILc1
# EYU2T3Wn1UFgj+H4L7yF4SzmQSmyzq+7Tml6Z2GzpsatdwCoFQz2nA28piCnRMCq
# lusMo2YdE6js9JS/h+zMqgKValuCyuU7S7ZbSO2dvYQwt/hgk07BegBrdsAENNh6
# 0IWRHrojwAg+4U6ULzbrBG6/hW2A8Q5065D8Nf9Bjy4eAU7QSbU=
# =K6xx
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 20 Aug 2024 08:59:27 PM AEST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu:
virtio-pci: Fix the use of an uninitialized irqfd
hw/audio/virtio-snd: fix invalid param check
vhost: Add VIRTIO_NET_F_RSC_EXT to vhost feature bits
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The crash was reported in MAC OS and NixOS, here is the link for this bug
https://gitlab.com/qemu-project/qemu/-/issues/2334https://gitlab.com/qemu-project/qemu/-/issues/2321
In this bug, they are using the virtio_input device. The guest notifier was
not supported for this device, The function virtio_pci_set_guest_notifiers()
was not called, and the vector_irqfd was not initialized.
So the fix is adding the check for vector_irqfd in virtio_pci_get_notifier()
The function virtio_pci_get_notifier() can be used in various devices.
It could also be called when VIRTIO_CONFIG_S_DRIVER_OK is not set. In this situation,
the vector_irqfd being NULL is acceptable. We can allow the device continue to boot
If the vector_irqfd still hasn't been initialized after VIRTIO_CONFIG_S_DRIVER_OK
is set, it means that the function set_guest_notifiers was not called before the
driver started. This indicates that the device is not using the notifier.
At this point, we will let the check fail.
This fix is verified in vyatta,MacOS,NixOS,fedora system.
The bt tree for this bug is:
Thread 6 "CPU 0/KVM" received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7c817be006c0 (LWP 1269146)]
kvm_virtio_pci_vq_vector_use () at ../qemu-9.0.0/hw/virtio/virtio-pci.c:817
817 if (irqfd->users == 0) {
(gdb) thread apply all bt
...
Thread 6 (Thread 0x7c817be006c0 (LWP 1269146) "CPU 0/KVM"):
0 kvm_virtio_pci_vq_vector_use () at ../qemu-9.0.0/hw/virtio/virtio-pci.c:817
1 kvm_virtio_pci_vector_use_one () at ../qemu-9.0.0/hw/virtio/virtio-pci.c:893
2 0x00005983657045e2 in memory_region_write_accessor () at ../qemu-9.0.0/system/memory.c:497
3 0x0000598365704ba6 in access_with_adjusted_size () at ../qemu-9.0.0/system/memory.c:573
4 0x0000598365705059 in memory_region_dispatch_write () at ../qemu-9.0.0/system/memory.c:1528
5 0x00005983659b8e1f in flatview_write_continue_step.isra.0 () at ../qemu-9.0.0/system/physmem.c:2713
6 0x000059836570ba7d in flatview_write_continue () at ../qemu-9.0.0/system/physmem.c:2743
7 flatview_write () at ../qemu-9.0.0/system/physmem.c:2774
8 0x000059836570bb76 in address_space_write () at ../qemu-9.0.0/system/physmem.c:2894
9 0x0000598365763afe in address_space_rw () at ../qemu-9.0.0/system/physmem.c:2904
10 kvm_cpu_exec () at ../qemu-9.0.0/accel/kvm/kvm-all.c:2917
11 0x000059836576656e in kvm_vcpu_thread_fn () at ../qemu-9.0.0/accel/kvm/kvm-accel-ops.c:50
12 0x0000598365926ca8 in qemu_thread_start () at ../qemu-9.0.0/util/qemu-thread-posix.c:541
13 0x00007c8185bcd1cf in ??? () at /usr/lib/libc.so.6
14 0x00007c8185c4e504 in clone () at /usr/lib/libc.so.6
Fixes: 2ce6cff94d ("virtio-pci: fix use of a released vector")
Cc: qemu-stable@nongnu.org
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20240806093715.65105-1-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 9b6083465f ("virtio-snd: check for invalid param shift
operands") tries to prevent invalid parameters specified by the
guest. However, the code is not correct.
Change the code so that the parameters format and rate, which are
a bit numbers, are compared with the bit size of the data type.
Fixes: 9b6083465f ("virtio-snd: check for invalid param shift operands")
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20240802071805.7123-1-vr_qemu@t-online.de>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VIRTIO_NET_F_RSC_EXT is implemented in the rx data path, which vhost
implements, so vhost needs to support the feature if it is ever to be
enabled with vhost. The feature must be disabled otherwise.
Fixes: 2974e916df ("virtio-net: support RSC v4/v6 tcp traffic for Windows HCK")
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240802-rsc-v1-1-2b607bd2f555@daynix.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Yutaro Shimizu from the Cyber Defense Institute discovered a bug in the
NVMe emulation that leaks contents of an uninitialized heap buffer if
subsystem and FDP emulation are enabled.
Cc: qemu-stable@nongnu.org
Reported-by: Yutaro Shimizu <shimizu@cyberdefense.jp>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
- Null pointer dereference in IPI IOCSR (Jiaxun)
- Correct '-smbios type=4' in man page (Heinrich)
- Use correct MMU index in MIPS get_pte (Phil)
- Reset MPQEMU remote message using device_cold_reset (Peter)
- Update linux-user MIPS CPU list (Phil)
- Do not let exec_command read console if no pattern to wait for (Nick)
- Remove shadowed declaration warning (Pierrick)
- Restrict STQF opcode to SPARC V9 (Richard)
- Add missing Kconfig dependency for POWERNV ISA serial port (Bernhard)
- Do not allow vmport device without i8042 PS/2 controller (Kamil)
- Fix QCryptoTLSCredsPSK leak (Peter)
-----BEGIN PGP SIGNATURE-----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=lPMG
-----END PGP SIGNATURE-----
Merge tag 'hw-misc-20240820' of https://github.com/philmd/qemu into staging
Various fixes
- Null pointer dereference in IPI IOCSR (Jiaxun)
- Correct '-smbios type=4' in man page (Heinrich)
- Use correct MMU index in MIPS get_pte (Phil)
- Reset MPQEMU remote message using device_cold_reset (Peter)
- Update linux-user MIPS CPU list (Phil)
- Do not let exec_command read console if no pattern to wait for (Nick)
- Remove shadowed declaration warning (Pierrick)
- Restrict STQF opcode to SPARC V9 (Richard)
- Add missing Kconfig dependency for POWERNV ISA serial port (Bernhard)
- Do not allow vmport device without i8042 PS/2 controller (Kamil)
- Fix QCryptoTLSCredsPSK leak (Peter)
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmbDzAsACgkQ4+MsLN6t
# wN7SvBAAwM0Frtg4ZKDZQu8XgMjLq1xVoSWjC3YJZKTpyGap5gO+7StvHg0sf9iB
# YyGqocCO+qdj9a7pTSasfGDyufpwoIZkOqkwGUWKBos76cOcHWt4e/gkl9O65Lf1
# VVKX4/xdY+a5w2eVAAdWWrYdaPWkKLm0ZZXKoeSIvN4R9A41j7J4kANhE2SweczF
# NnTt2gBnSlpRzghlVWPJKhnq+aYbvLeR7ApdNGUJDpSI1ZTh9gH1GtZFwBN7aeDo
# PvDucoui0EmuyHTVdOYOH3zihTfzKlNZECcT3Y6/6i8y5p7jLHyINHHexsKw6T56
# i5RidJMPTfM0EO6LU1GvUN5FzZy24zXOf298Fe/GMYczQsOznQd4+aFHYPb3d4hZ
# 8Vc1wB1s8XF5WGj+7bchBAUdynUnbwUqfMOb2pMXLIm21pSDnOTVgmYMnp1Kt4AA
# 9WbHiS6tUJf/HjQsep8BBNGUiVSsUPDNNhL8QN43u2C0NgNRPgtRuIV+ytgVXS1G
# 2t1QiRX0lX4ACHmw88agUCU3OhorumuDOpoitQK5jn2VutT7TqbGgibkQMFSgn9E
# Xwrmtlf7nYU9MVgXYJjH2bBh7wbOmQCqbHniEj0targkxccAMJoswG4vtKsP9zkd
# tBs6qMiZ8qSj5eoq8JBRF8bF4tONmboPZjRlboACJ0kTD5wCElA=
# =lPMG
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 20 Aug 2024 08:49:47 AM AEST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
* tag 'hw-misc-20240820' of https://github.com/philmd/qemu:
crypto/tlscredspsk: Free username on finalize
hw/i386/pc: Ensure vmport prerequisites are fulfilled
hw/i386/pc: Unify vmport=auto handling
hw/ppc/Kconfig: Add missing SERIAL_ISA dependency to POWERNV machine
target/sparc: Restrict STQF to sparcv9
contrib/plugins/execlog: Fix shadowed declaration warning
tests/avocado: Mark ppc_hv_tests.py as non-flaky after fixed console interaction
tests/avocado: exec_command should not consume console output
linux-user/mips: Select Loongson CPU for Loongson binaries
linux-user/mips: Select MIPS64R2-generic for Rel2 binaries
linux-user/mips: Select Octeon68XX CPU for Octeon binaries
linux-user/mips: Do not try to use removed R5900 CPU
hw/remote/message.c: Don't directly invoke DeviceClass:reset
hw/dma/xilinx_axidma: Use semicolon at end of statement, not comma
target/mips: Load PTE as DATA
target/mips: Use correct MMU index in get_pte()
target/mips: Pass page table entry size as MemOp to get_pte()
qemu-options.hx: correct formatting -smbios type=4
hw/mips/loongson3_virt: Fix condition of IPI IOCSR connection
hw/mips/loongson3_virt: Store core_iocsr into LoongsonMachineState
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since commit 4ccd5fe22f ('pc: add option
to disable PS/2 mouse/keyboard'), the vmport will not be created unless
the i8042 PS/2 controller is enabled. To avoid confusion, let's fail if
vmport was explicitly requested, but the i8042 controller is disabled.
This also changes the behavior of vmport=auto to take i8042 controller
availability into account.
Signed-off-by: Kamil Szczęk <kamil@szczek.dev>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-ID: <0MS3y5E-hHqODIhiuFxmCnIrXd612JIGq31UuMsz4KGCKZ_wWuF-PHGKTRSGS0nWaPEddOdF4YOczHdgorulECPo792OhWov7O9BBF6UMX4=@szczek.dev>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The code which translates vmport=auto to on/off is currently separate
for each PC machine variant, while being functionally equivalent.
This moves the translation into a shared initialization function, while
also tightening the enum assertion.
Signed-off-by: Kamil Szczęk <kamil@szczek.dev>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <v8pz1uwgIYWkidgZK-o8H-qJvnSyl0641XVmNO43Qls307AA3QRPuad_py6xGe0JAxB6yDEe76oZ8tau_n-2Y6sJBCKzCujNbEUUFhd-ahI=@szczek.dev>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The machine calls serial_hds_isa_init() which is provided by serial-isa.c,
guarded by SERIAL_ISA.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240814181534.218964-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Directly invoking the DeviceClass::reset method is a bad idea,
because if the device is using three-phase reset then it relies on
transitional reset machinery which is likely to disappear at some
point.
Reset the device in the standard way, by calling device_cold_reset().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240813165250.2717650-7-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In axidma_class_init() we accidentally used a comma at the end of
a statement rather than a semicolon. This has no ill effects, but
it's obviously not intended and it means that Coccinelle scripts
for instance will fail to match on the two statements. Use a
semicolon instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240813165250.2717650-6-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
>>> CID 1547264: Null pointer dereferences (REVERSE_INULL)
>>> Null-checking "ipi" suggests that it may be null, but it has already been dereferenced on all paths leading to the check.
Resolves: Coverity CID 1547264
Link: https://lore.kernel.org/qemu-devel/752417ad-ab72-4fed-8d1f-af41f15bc225@app.fastmail.com/
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240621-loongson3-ipi-follow-v2-2-848eafcbb67e@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Link: https://lore.kernel.org/qemu-devel/972034d6-23b3-415a-b401-b8bc1cc515c9@linaro.org/
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240621-loongson3-ipi-follow-v2-1-848eafcbb67e@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This reverts commit f42cdf2ea5.
Linux does not properly handle '#msi-cells=<0>' when searching for
MSI controllers for PCI devices which results in the devices being
unable to use MSIs. A patch for Linux has been sent[1] but until it,
or something like it, is merged and in distro kernels we should stop
adding the property. It's harmless to stop adding it since the
absence of the property and a value of zero for the property mean
the same thing according to the DT binding definition.
Link: https://lore.kernel.org/all/20240816124957.130017-2-ajones@ventanamicro.com/ # 1
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240816160743.220374-5-ajones@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fix the misspellings of "overriden" also in code comments.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240813125638.395461-1-sw@weilnetz.de>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240813202329.1237572-20-alex.bennee@linaro.org>
Receive coalescing is visible to the target machine, so its timers
should use virtual time like other timers in virtio-net, to be
compatible with record-replay.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20240813050638.446172-10-npiggin@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240813202329.1237572-18-alex.bennee@linaro.org>
The regular qemu_bh_schedule() calls result in non-deterministic
execution of the bh in record-replay mode, which causes replay failure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20240813050638.446172-9-npiggin@gmail.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240813202329.1237572-17-alex.bennee@linaro.org>
This commit adds validation checks for the MCOPRE and MCOSEL values in
the rcc_update_cfgr_register function. If the MCOPRE value exceeds
0b100 or the MCOSEL value exceeds 0b111, an error is logged and the
corresponding clock mux is disabled. This helps in identifying and
handling invalid configurations in the RCC registers.
Reproducer:
cat << EOF | qemu-system-aarch64 -display \
none -machine accel=qtest, -m 512M -machine b-l475e-iot01a -qtest \
stdio
writeq 0x40021008 0xffffffff
EOF
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2356
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Having magic numbers inside the code is not a good idea, as it
is error-prone. So, instead, create a macro with the number
definition.
Link: https://lore.kernel.org/qemu-devel/CAFEAcA-PYnZ-32MRX+PgvzhnoAV80zBKMYg61j2f=oHaGfwSsg@mail.gmail.com/
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: ef0e7f5fca6cd94eda415ecee670c3028c671b74.1723121692.git.mchehab+huawei@kernel.org
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The real period is zero when both period and period_frac are zero.
Check the method ptimer_set_freq, if freq is larger than 1000 MHz,
the period is zero, but the period_frac is not, in this case, the
ptimer will work but the current code incorrectly recognizes that
the ptimer is disabled.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2306
Signed-off-by: JianZhou Yue <JianZhou.Yue@verisilicon.com>
Message-id: 3DA024AEA8B57545AF1B3CAA37077D0FB75E82C8@SHASXM03.verisilicon.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the case of scsi-block, RESERVATION_CONFLICT is not a backend error,
but indicates that the guest tried to make a request that it isn't
allowed to execute. Pass the error to the guest so that it can decide
what to do with it.
Without this, if we stop the VM in response to a RESERVATION_CONFLICT
(as is the default policy in management software such as oVirt or
KubeVirt), it can happen that the VM cannot be resumed any more because
every attempt to resume it immediately runs into the same error and
stops the VM again.
One case that expects RESERVATION_CONFLICT errors to be visible in the
guest is running the validation tests in Windows 2019's Failover Cluster
Manager, which intentionally tries to execute invalid requests to see if
they are properly rejected.
Buglink: https://issues.redhat.com/browse/RHEL-50000
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240731123207.27636-5-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
scsi_block_sgio_complete() has surprising behaviour in that there are
error cases in which it directly completes the request and never calls
the passed callback. In the current state of the code, this doesn't seem
to result in bugs, but with future code changes, we must be careful to
never rely on the callback doing some cleanup until this code smell is
fixed. For now, just add warnings to make people aware of the trap.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240731123207.27636-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of calling into scsi_handle_rw_error() directly from
scsi_block_sgio_complete() and skipping the normal callback, go through
the normal cleanup path by calling the callback with a positive error
value.
The important difference here is not only that the code path is cleaner,
but that the callbacks set r->req.aiocb = NULL. If we skip setting this
and the error action is BLOCK_ERROR_ACTION_STOP, resuming the VM runs
into an assertion failure in scsi_read_data() or scsi_write_data()
because the dangling aiocb pointer is unexpected.
Fixes: a108557bbf ("scsi: inline sg_io_sense_from_errno() into the callers.")
Buglink: https://issues.redhat.com/browse/RHEL-50000
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240731123207.27636-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In some error cases, scsi_block_sgio_complete() never calls the passed
callback, but directly completes the request. This leads to bugs because
its error paths are not exact copies of what the callback would normally
do.
In preparation to fix this, allow passing positive return values to the
callbacks that represent the status code that should be used to complete
the request.
scsi_handle_rw_error() already handles positive values for its ret
parameter because scsi_block_sgio_complete() calls directly into it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240731123207.27636-2-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reset config values in the device RESET phase, not only once
when the device is realized, because otherwise the device can
use unknown values at reset.
Since we are adding a new reset method, use the preferred
Resettable API (for a simple leaf device reset, a
DeviceClass::reset method and a ResettableClass::reset_hold
method are essentially identical).
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240802213122.86852-3-philmd@linaro.org>
When booting Linux we see:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000
pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
This is due to missing base address register write mask.
Add it to get:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000
pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff pref]
pci 0000:00:00.0: reg 0x14: [mem 0x01000000-0x01000fff pref]
pci 0000:00:00.0: reg 0x18: [mem 0x1c000000-0x1c000fff]
pci 0000:00:00.0: reg 0x1c: [mem 0x1f000000-0x1f000fff]
pci 0000:00:00.0: reg 0x20: [mem 0x1be00000-0x1be00fff]
pci 0000:00:00.0: reg 0x24: [io 0x14000000-0x14000fff]
Since this device is only used by MIPS machines which aren't
versioned, we don't need to update migration compat machinery.
Mention the datasheet referenced. Remove the "Malta assumptions
ahead" comment since the reset values from the datasheet are used.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240802213122.86852-2-philmd@linaro.org>
If the user tries to use the virtio-gpu-gl device but the display
backend doesn't have OpenGL support enabled, we currently print a
rather uninformative error message:
$ qemu-system-aarch64 -M virt -device virtio-gpu-gl
qemu-system-aarch64: -device virtio-gpu-gl: opengl is not available
Since OpenGL is not enabled on display frontends by default, users
are quite likely to run into this. Improve the error message to
be more specific and to suggest to the user a path forward.
Note that the case of "user tried to enable OpenGL but the display
backend doesn't handle it" is caught elsewhere first, so we can
assume that isn't the problem:
$ qemu-system-aarch64 -M virt -device virtio-gpu-gl -display curses,gl=on
qemu-system-aarch64: OpenGL is not supported by the display
(Use of error_append_hint() requires us to add an ERRP_GUARD() to
the function, as noted in include/qapi/error.h.)
With this commit we now produce the hopefully more helpful error:
$ ./build/x86/qemu-system-aarch64 -M virt -device virtio-gpu-gl
qemu-system-aarch64: -device virtio-gpu-gl: The display backend does not have OpenGL support enabled
It can be enabled with '-display BACKEND,gl=on' where BACKEND is the name of the display backend to use.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2443
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-ID: <20240731154136.3494621-2-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Coverity notes that the code at the end of the loop in
bmdma_prepare_buf() is unreachable. This is because in commit
9fbf0fa81f ("ide: remove hardcoded 2GiB transactional limit")
we removed the only codepath in the loop which could "break" out of
it, but didn't notice that this meant we should also remove the code
at the end of the loop.
Remove the dead code.
Resolves: Coverity CID 1547772
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[PMD: Break and return once at EOF]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240805182419.22239-1-philmd@linaro.org>
Coverity complains about an overflow in isa_fdc_get_drive_max_chs()
that can happen if the loop over fd_formats never finds a match,
because we initialize *maxc to 0 and then at the end of the
function decrement it.
This can't ever actually happen because fd_formats has at least
one entry for each FloppyDriveType, so we must at least once
find a match and update *maxc, *maxh and *maxs. Assert that we
did find a match, which should keep Coverity happy and will also
detect possible bugs in the data in fd_formats.
Resolves: Coverity CID 1547663
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240731143617.3391947-6-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In ide_atapi_cmd_reply_end() we calculate a 16-bit size, and then
assign its two halves to s->lcyl and s->hcyl like this:
s->lcyl = size;
s->hcyl = size >> 8;
Coverity warns that the first line here can overflow the
8-bit s->lcyl variable. This is true, and in this case we're
deliberately only after the low 8 bits of the value. The
code is clearer to both humans and Coverity if we're explicit
that we only wanted the low 8 bits, though.
Resolves: Coverity CID 1547621
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240731143617.3391947-5-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In pflash_write() Coverity points out that we can decrement the
unsigned pfl->counter below zero, which makes it wrap around. In
fact this is harmless, because if pfl->counter is 0 at this point we
also increment pfl->wcycle to 3, and the wcycle == 3 handling doesn't
look at counter; the only way back into code which looks at the
counter value is via wcycle == 1, which will reinitialize the counter.
But it's arguably a little clearer to break early in the "counter ==
0" if(), to avoid the decrement-below-zero.
Resolves: Coverity CID 1547611
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240731143617.3391947-4-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
We neglected to clear the @data_count index on ADMA error,
allowing to trigger assertion in sdhci_read_dataport() or
sdhci_write_dataport().
Cc: qemu-stable@nongnu.org
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2455
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240730092138.32443-4-philmd@linaro.org>
Guest should not try to read the DAT lines from invalid
command state. If it still insists to do so, return a
dummy value.
Cc: qemu-stable@nongnu.org
Fixes: e2dec2eab0 ("hw/sd/sdcard: Remove default case in read/write on DAT lines")
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2454
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240730092138.32443-3-philmd@linaro.org>
On error the DAT lines are left unmodified to their
previous states. QEMU returns 0x00 for convenience.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240730092138.32443-2-philmd@linaro.org>
Now than LoongArch target can use the TYPE_LOONGARCH_IPI
model, restrict TYPE_LOONGSON_IPI to MIPS.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-15-philmd@linaro.org>
Loongarch IPI inherits from class LoongsonIPICommonClass, and it
only contains Loongarch 3A5000 virt machine specific interfaces,
rather than mix different machine implementations together.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Rebased]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-14-philmd@linaro.org>
Loongarch IPI is added here, it inherits from class
TYPE_LOONGSON_IPI_COMMON, and two interfaces get_iocsr_as() and
cpu_by_arch_id() are added for Loongarch 3A5000 machine. It can
be used when ipi is emulated in userspace with KVM mode.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Rebased and simplified]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-13-philmd@linaro.org>
Move the common code from loongson_ipi.c to loongson_ipi_common.c,
call parent_realize() instead of loongson_ipi_common_realize() in
loongson_ipi_realize().
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-12-philmd@linaro.org>
In order to access loongson_ipi_core_read/write helpers
from loongson_ipi_common.c in the next commit, make their
prototype declaration public.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-11-philmd@linaro.org>
Allow Loongson IPI implementations to have their own
cpu_by_arch_id() handler.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-10-philmd@linaro.org>
Allow Loongson IPI implementations to have their own get_iocsr_as()
handler.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-9-philmd@linaro.org>
In order to get LoongsonIPICommonClass in send_ipi_data()
in the next commit, propagate LoongsonIPICommonState.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-8-philmd@linaro.org>
Move the IPICore structure and corresponding common fields
of LoongsonIPICommonState to "hw/intc/loongson_ipi_common.h".
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-7-philmd@linaro.org>
It is easier to manage one array of MMIO MR rather
than one per vCPU.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-6-philmd@linaro.org>
Introduce LOONGSON_IPI_COMMON stubs, QDev parent of LOONGSON_IPI.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-4-philmd@linaro.org>
In preparation to extract common IPI code in few commits,
extract loongson_ipi_common_realize().
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-3-philmd@linaro.org>
We'll have to add LoongsonIPIClass in few commits,
so rename LoongsonIPI as LoongsonIPIState for clarity.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
[PMD: Extracted from bigger commit, added commit description]
Co-Developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20240805180622.21001-2-philmd@linaro.org>
Patch 06b1297017 ("virtio-net: fix network stall under load")
added double-check to test whether the available buffer size
can satisfy the request or not, in case the guest has added
some buffers to the avail ring simultaneously after the first
check. It will be lucky if the available buffer size becomes
okay after the double-check, then the host can send the packet
to the guest. If the buffer size still can't satisfy the request,
even if the guest has added some buffers, viritio-net would
stall at the host side forever.
The patch enables notification and checks whether the guest has
added some buffers since last check of available buffers when
the available buffers are insufficient. If no buffer is added,
return false, else recheck the available buffers in the loop.
If the available buffers are sufficient, disable notification
and return true.
Changes:
1. Change the return type of virtqueue_get_avail_bytes() from void
to int, it returns an opaque that represents the shadow_avail_idx
of the virtqueue on success, else -1 on error.
2. Add a new API: virtio_queue_enable_notification_and_check(),
it takes an opaque as input arg which is returned from
virtqueue_get_avail_bytes(). It enables notification firstly,
then checks whether the guest has added some buffers since
last check of available buffers or not by virtio_queue_poll(),
return ture if yes.
The patch also reverts patch "06b12970174".
The case below can reproduce the stall.
Guest 0
+--------+
| iperf |
---------------> | server |
Host | +--------+
+--------+ | ...
| iperf |----
| client |---- Guest n
+--------+ | +--------+
| | iperf |
---------------> | server |
+--------+
Boot many guests from qemu with virtio network:
qemu ... -netdev tap,id=net_x \
-device virtio-net-pci-non-transitional,\
iommu_platform=on,mac=xx:xx:xx:xx:xx:xx,netdev=net_x
Each guest acts as iperf server with commands below:
iperf3 -s -D -i 10 -p 8001
iperf3 -s -D -i 10 -p 8002
The host as iperf client:
iperf3 -c guest_IP -p 8001 -i 30 -w 256k -P 20 -t 40000
iperf3 -c guest_IP -p 8002 -i 30 -w 256k -P 20 -t 40000
After some time, the host loses connection to the guest,
the guest can send packet to the host, but can't receive
packet from the host.
It's more likely to happen if SWIOTLB is enabled in the guest,
allocating and freeing bounce buffer takes some CPU ticks,
copying from/to bounce buffer takes more CPU ticks, compared
with that there is no bounce buffer in the guest.
Once the rate of producing packets from the host approximates
the rate of receiveing packets in the guest, the guest would
loop in NAPI.
receive packets ---
| |
v |
free buf virtnet_poll
| |
v |
add buf to avail ring ---
|
| need kick the host?
| NAPI continues
v
receive packets ---
| |
v |
free buf virtnet_poll
| |
v |
add buf to avail ring ---
|
v
... ...
On the other hand, the host fetches free buf from avail
ring, if the buf in the avail ring is not enough, the
host notifies the guest the event by writing the avail
idx read from avail ring to the event idx of used ring,
then the host goes to sleep, waiting for the kick signal
from the guest.
Once the guest finds the host is waiting for kick singal
(in virtqueue_kick_prepare_split()), it kicks the host.
The host may stall forever at the sequences below:
Host Guest
------------ -----------
fetch buf, send packet receive packet ---
... ... |
fetch buf, send packet add buf |
... add buf virtnet_poll
buf not enough avail idx-> add buf |
read avail idx add buf |
add buf ---
receive packet ---
write event idx ... |
wait for kick add buf virtnet_poll
... |
---
no more packet, exit NAPI
In the first loop of NAPI above, indicated in the range of
virtnet_poll above, the host is sending packets while the
guest is receiving packets and adding buffers.
step 1: The buf is not enough, for example, a big packet
needs 5 buf, but the available buf count is 3.
The host read current avail idx.
step 2: The guest adds some buf, then checks whether the
host is waiting for kick signal, not at this time.
The used ring is not empty, the guest continues
the second loop of NAPI.
step 3: The host writes the avail idx read from avail
ring to used ring as event idx via
virtio_queue_set_notification(q->rx_vq, 1).
step 4: At the end of the second loop of NAPI, recheck
whether kick is needed, as the event idx in the
used ring written by the host is beyound the
range of kick condition, the guest will not
send kick signal to the host.
Fixes: 06b1297017 ("virtio-net: fix network stall under load")
Cc: qemu-stable@nongnu.org
Signed-off-by: Wencheng Yang <east.moutain.yang@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Ensure the queue index points to a valid queue when software RSS
enabled. The new calculation matches with the behavior of Linux's TAP
device with the RSS eBPF program.
Fixes: 4474e37a5b ("virtio-net: implement RX RSS processing")
Reported-by: Zhibin Hu <huzhibin5@huawei.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Old linux kernel rtl8139 drivers (ex. debian 2.1) uses outb to set the rx
mode for RxConfig. Unfortunatelly qemu does not support outb for RxConfig.
Signed-off-by: Hans <sungdgdhtryrt@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
If VT-D hardware supports scalable mode, Linux will set the IQA DW field
(bit11). In qemu, the vtd_mem_write and vtd_update_iq_dw set DW field well.
However, vtd_mem_read the DW field wrong because "& VTD_IQA_QS" dropped the
value of DW.
Replace "&VTD_IQA_QS" with "& (VTD_IQA_QS | VTD_IQA_DW_MASK)" could save
the DW field.
Test patch as below:
config the "x-scalable-mode" option:
"-device intel-iommu,caching-mode=on,x-scalable-mode=on,aw-bits=48"
After Linux OS boot, check the IQA_REG DW Field by usage 1 or 2:
1. IOMMU_DEBUGFS:
Before fix:
cat /sys/kernel/debug/iommu/intel/iommu_regset |grep IQA
IQA 0x90 0x00000001001da001
After fix:
cat /sys/kernel/debug/iommu/intel/iommu_regset |grep IQA
IQA 0x90 0x00000001001da801
Check DW field(bit11) is 1.
2. devmem2 read the IQA_REG (offset 0x90):
Before fix:
devmem2 0xfed90090
/dev/mem opened.
Memory mapped at address 0x7f72c795b000.
Value at address 0xFED90090 (0x7f72c795b090): 0x1DA001
After fix:
devmem2 0xfed90090
/dev/mem opened.
Memory mapped at address 0x7fc95281c000.
Value at address 0xFED90090 (0x7fc95281c090): 0x1DA801
Check DW field(bit11) is 1.
Signed-off-by: yeeli <seven.yi.lee@gmail.com>
Message-Id: <20240725031858.1529902-1-seven.yi.lee@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In amdvi_update_iotlb() we will only put a new entry in the hash
table if to_cache.perm is not IOMMU_NONE. However we allocate the
memory for the new AMDVIIOTLBEntry and for the hash table key
regardless. This means that in the IOMMU_NONE case we will leak the
memory we alloacted.
Move the allocations into the if() to the point where we know we're
going to add the item to the hash table.
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2452
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240731170019.3590563-1-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Jamin Lin