After assigning a NVMe/SCSI controller to guest by VFIO, we lose
everything on the host side. A guest uses these devices exclusively,
we usually don't care the actions on these devices. But there is a
low probability that hitting physical hardware warning, we need a
chance to get the basic smart log info.
Introduce disk smart, and implement NVMe smart on linux.
Thanks to Keith and Marc-André.
CC: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220420022610.418052-3-pizhenwei@bytedance.com>
Assigning a NVMe disk by VFIO or emulating a NVMe controller by QEMU,
a NVMe disk get exposed in guest side. Support NVMe disk bus type and
implement posix version.
Test PCI passthrough case:
~#virsh qemu-agent-command buster '{"execute":"guest-get-disks"}' | jq
...
{
"name": "/dev/nvme0n1",
"dependencies": [],
"partition": false,
"address": {
"serial": "SAMSUNG MZQL23T8HCLS-00A07_S64HNE0N500076",
"bus-type": "nvme",
"bus": 0,
"unit": 0,
"pci-controller": {
"bus": 0,
"slot": 22,
"domain": 0,
"function": 0
},
"dev": "/dev/nvme0n1",
"target": 0
}
...
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220420022610.418052-2-pizhenwei@bytedance.com>
On Solaris, instead of the -P, -H, and -r flags, we need to provide
the target init state to the 'shutdown' command: state 5 is poweroff,
0 is halt, and 6 is reboot. We also need to pass -g0 to avoid the
default 60-second delay, and -y to avoid a confirmation prompt.
Implement this logic under an #ifdef CONFIG_SOLARIS, so the
'guest-shutdown' command works properly on Solaris.
Signed-off-by: Andrew Deason <adeason@sinenomine.net>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220426195526.7699-6-adeason@sinenomine.net>
guest_get_network_stats can silently fail in a couple of ways. Add
debug messages to these cases, so we're never completely silent on
failure.
Signed-off-by: Andrew Deason <adeason@sinenomine.net>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220426195526.7699-5-adeason@sinenomine.net>
The code for guest-network-get-interfaces needs a couple of small
adjustments for Solaris:
- The results from SIOCGIFHWADDR are documented as being in ifr_addr,
not ifr_hwaddr (ifr_hwaddr doesn't exist on Solaris).
- The implementation of guest_get_network_stats is Linux-specific, so
hide it under #ifdef CONFIG_LINUX. On non-Linux, we just won't
provide network interface stats.
Signed-off-by: Andrew Deason <adeason@sinenomine.net>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Message-Id: <20220426195526.7699-4-adeason@sinenomine.net>
Since its introduction in commit 3424fc9f16 ("qemu-ga: add
guest-network-get-interfaces command"), guest-network-get-interfaces
seems to check if a given interface has a hardware address by checking
'ifa->ifa_flags & SIOCGIFHWADDR'. But ifa_flags is a field for IFF_*
flags (IFF_UP, IFF_LOOPBACK, etc), and comparing it to an ioctl like
SIOCGIFHWADDR doesn't make sense.
On Linux, this isn't a big deal, since SIOCGIFHWADDR has so many bits
set (0x8927), 'ifa->ifa_flags & SIOCGIFHWADDR' will usually have a
nonzero result for any 'normal'-looking interfaces: anything with
IFF_UP (0x1) or IFF_BROADCAST (0x2) set, as well as several
less-common flags. This means we'll try to get the hardware address
for most/all interfaces, even those that don't really have one (like
the loopback device). For those interfaces, Linux just returns a
hardware address of all zeroes.
On Solaris, however, trying to get the hardware address for a loopback
device returns an EADDRNOTAVAIL error. This causes us to return an
error and the entire guest-network-get-interfaces call fails.
Change this logic to always try to get the hardware address for each
interface, and don't return an error if we fail to get it. Instead,
just don't include the 'hardware-address' field in the result if we
can't get the hardware address.
Signed-off-by: Andrew Deason <adeason@sinenomine.net>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Message-Id: <20220426195526.7699-3-adeason@sinenomine.net>
Currently, commands-posix.c assumes that getifaddrs() is only
available on Linux, and so the related guest agent command
guest-network-get-interfaces is only implemented for #ifdef __linux__.
This function does exist on other platforms, though, such as Solaris.
So, add a meson check for getifaddrs(), and move the code for
guest-network-get-interfaces to be built whenever getifaddrs() is
available.
The implementation for guest-network-get-interfaces still has some
Linux-specific code, which is not fixed in this commit. This commit
moves the relevant big chunks of code around without changing them, so
a future commit can change the code in place.
Signed-off-by: Andrew Deason <adeason@sinenomine.net>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Message-Id: <20220426195526.7699-2-adeason@sinenomine.net>
* New AST1030 SoC and eval board
* Accumulative mode support for HACE controller
* GPIO fix and unit test
* Clock modeling adjustments for the AST2600
* Dummy eMMC Boot Controller model
* Change of AST2500 EVB and AST2600 EVB flash model (for quad IO)
-----BEGIN PGP SIGNATURE-----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=+hIh
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20220503' of https://github.com/legoater/qemu into staging
aspeed queue:
* New AST1030 SoC and eval board
* Accumulative mode support for HACE controller
* GPIO fix and unit test
* Clock modeling adjustments for the AST2600
* Dummy eMMC Boot Controller model
* Change of AST2500 EVB and AST2600 EVB flash model (for quad IO)
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmJwwq8ACgkQUaNDx8/7
# 7KF0IhAApbCCcg06PR66pmaDBFY2RWmU0XShDoCEeHyT5huQFcAJWNoqVAJ52E8L
# ZCPEeORQthxMwmtw7JLIGCFhDx4P4YzfNZRPANRosKs7BR0GequVgHp7c6fXhD/3
# A3w42hfuNR4Hrbsil/yhN2vxFAYXudA+NPez2ibex3UyVc/ZUu71nCqZTxh3wZdN
# XQTuqxWerA5RRBRtVn8n/aBp+3mo5enD4dx44KWMZxKxJaFJfZQHVZttGHU9azF+
# fXJ1lmrJZ7eHmWjCEvgnHXwl0nWiMwkLZ9/MKOAPkdjUG1JciGRxbJki0bGuS7Jr
# NzOyO0f++ZtOsuLGA03WiwR1oo3GmG7lBFqBcdzMwN2EMvDvVvJUp3v8IdV/L10P
# OJ10rBi6FDJuKGHJGIQywlFSYYjPb+DgNEWId2rugVVm4dR02Cn69amuL40OO9by
# /C7hO9gSvRTqSSdjFcdkbI2h+kx0354F2/gR2LFLBh1KUHulTJ4ErthrKBiuNPC8
# tsELzYVnxWVT+nc30Nmidg3uCW3/5zBlaj0qlL4aiFjKR5na6Wpz+oE/aNiNdyT3
# IBI+J5zvbtn/prNTWLW1TCuGdwj357LfYfkfkH8eqZWfX5vGq+5hVTc/m8EW5Cx8
# yV8JrbjX8uDI379skdl4imtedbKZhPLd7csM/zrorsJhBBwSoLA=
# =+hIh
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 02 May 2022 10:50:39 PM PDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20220503' of https://github.com/legoater/qemu:
aspeed/hace: Support AST1030 HACE
hw/gpio/aspeed_gpio: Fix QOM pin property
tests/qtest: Add test for Aspeed HACE accumulative mode
aspeed/hace: Support AST2600 HACE
aspeed/hace: Support HMAC Key Buffer register.
hw/arm/aspeed: fix AST2500/AST2600 EVB fmc model
test/avocado/machine_aspeed.py: Add ast1030 test case
aspeed: Add an AST1030 eval board
aspeed/soc : Add AST1030 support
aspeed/scu: Add AST1030 support
aspeed/timer: Add AST1030 support
aspeed/wdt: Add AST1030 support
aspeed/wdt: Fix ast2500/ast2600 default reload value
aspeed/smc: Add AST1030 support
aspeed/adc: Add AST1030 support
aspeed: Add eMMC Boot Controller stub
aspeed: sbc: Correct default reset values
hw: aspeed_scu: Introduce clkin_25Mhz attribute
hw: aspeed_scu: Add AST2600 apb_freq and hpll calculation function
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The qemu_*block() functions are meant to be be used with sockets (the
win32 implementation expects SOCKET)
Over time, those functions where used with Win32 SOCKET or
file-descriptors interchangeably. But for portability, they must only be
used with socket-like file-descriptors. FDs can use
g_unix_set_fd_nonblocking() instead.
Rename the functions with "socket" in the name to prevent bad usages.
This is effectively reverting commit f9e8cacc55 ("oslib-posix:
rename socket_set_nonblock() to qemu_set_nonblock()").
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The call is POSIX-specific. Use the dedicated GLib API.
(this is a preliminary patch before renaming qemu_set_nonblock())
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Those calls are POSIX-specific. Use the dedicated GLib
API. (qemu_set_nonblock() is for socket-like)
(this is a preliminary patch before renaming qemu_set_nonblock())
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The call is POSIX-specific. Use the dedicated GLib API.
(this is a preliminary patch before renaming qemu_set_nonblock())
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Those calls are non-socket fd, or are POSIX-specific. Use the dedicated
GLib API. (qemu_set_nonblock() is for socket-like)
(this is a preliminary patch before renaming qemu_set_nonblock())
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The call is POSIX-specific. Use the dedicated GLib API.
(this is a preliminary patch before renaming qemu_set_nonblock())
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Those calls are non-socket fd, or are POSIX-specific. Use the dedicated
GLib API. (qemu_set_nonblock() is for socket-like)
(this is a preliminary patch before renaming qemu_set_nonblock())
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Those calls are either for non-socket fd, or are POSIX-specific. Use the
dedicated GLib API. (qemu_set_nonblock() is for socket-like)
(this is a preliminary patch before renaming qemu_set_nonblock())
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The function isn't used outside of qio_channel_command_new_spawn(),
which is !win32-specific.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
GLib g_unix_open_pipe() is essentially like qemu_pipe(), available since
2.30.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
It is only used by block/file-posix.c, move it there.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
API available since glib 2.30. It also preserves errno.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This will help moving QAPI/QMP in a common subproject.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Since commit a2ce7dbd91 ("meson: convert tests/qtest to meson"),
libqtest.h is under libqos/ directory, while libqtest.c is still in
qtest/. Move back to its original location to avoid mixing with libqos/.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Per ast1030_v7.pdf, AST1030 HACE engine is identical to AST2600's HACE
engine.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
I was setting gpioV4-7 to "1110" using the QOM pin property handler and
noticed that lowering gpioV7 was inadvertently lowering gpioV4-6 too.
(qemu) qom-set /machine/soc/gpio gpioV4 true
(qemu) qom-set /machine/soc/gpio gpioV5 true
(qemu) qom-set /machine/soc/gpio gpioV6 true
(qemu) qom-get /machine/soc/gpio gpioV4
true
(qemu) qom-set /machine/soc/gpio gpioV7 false
(qemu) qom-get /machine/soc/gpio gpioV4
false
An expression in aspeed_gpio_set_pin_level was using a logical NOT
operator instead of a bitwise NOT operator:
value &= !pin_mask;
The original author probably intended to make a bitwise NOT expression
"~", but mistakenly used a logical NOT operator "!" instead. Some
programming languages like Rust use "!" for both purposes.
Fixes: 4b7f956862 ("hw/gpio: Add basic Aspeed GPIO model for AST2400 and
AST2500")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220502080827.244815-1-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This add two addition test cases for accumulative mode under sg enabled.
The input vector was manually craft with "abc" + bit 1 + padding zeros + L.
The padding length depends on algorithm, i.e. SHA512 (1024 bit),
SHA256 (512 bit).
The result was calculated by command line sha512sum/sha256sum utilities
without padding, i.e. only "abc" ascii text.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg: checkpatch fixes ]
Message-Id: <20220426021120.28255-4-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The aspeed ast2600 accumulative mode is described in datasheet
ast2600v10.pdf section 25.6.4:
1. Allocating and initiating accumulative hash digest write buffer
with initial state.
* Since QEMU crypto/hash api doesn't provide the API to set initial
state of hash library, and the initial state is already set by
crypto library (gcrypt/glib/...), so skip this step.
2. Calculating accumulative hash digest.
(a) When receiving the last accumulative data, software need to add
padding message at the end of the accumulative data. Padding
message described in specific of MD5, SHA-1, SHA224, SHA256,
SHA512, SHA512/224, SHA512/256.
* Since the crypto library (gcrypt/glib) already pad the
padding message internally.
* This patch is to remove the padding message which fed byguest
machine driver.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220426021120.28255-3-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Support HACE28: Hash HMAC Key Buffer Base Address Register.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220426021120.28255-2-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Current fmc model of AST2500 EVB and AST2600 EVB can't emulate quad
mode properly so fix them using equivalent mx25l25635e and mx66u51235f
respectively.
These default settings still can be overridden using the 'fmc-model'
command line option.
Reported-by: Graeme Gregory <quic_ggregory@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220402184427.4010304-1-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add test case to test "ast1030-evb" machine with zephyr os
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-10-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The image should be supplied with ELF binary.
$ qemu-system-arm -M ast1030-evb -kernel zephyr.elf -nographic
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-9-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The embedded core of AST1030 SoC is ARM Coretex M4.
It is hard to be integrated in the common Aspeed Soc framework.
We introduce a new ast1030 class with instance_init and realize
handlers.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: rename aspeed_ast10xx.c to aspeed_ast10x0.c to match zephyr ]
Message-Id: <20220401083850.15266-8-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per ast1030_v07.pdf, AST1030 SOC doesn't have SCU300, the pclk divider
selection is defined in SCU310[11:8].
Add a get_apb_freq function and a class init handler for ast1030.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-7-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
ast1030 tmc(timer controller) is identical to ast2600 tmc.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-6-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST1030 wdt controller is similiar to AST2600's wdt, but it has extra
registers.
Introduce ast1030 object class and increse the number of regs(offset) of
ast1030 model.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-5-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per ast2500_2520_datasheet_v1.8 and ast2600v11.pdf, the default value of
WDT00 and WDT04 is 0x014FB180 for ast2500/ast2600.
Add default_status and default_reload_value attributes for storing
counter status and reload value as they are different from ast2400.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-4-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST1030 spi controller's address decoding unit is 1MB that is identical
to ast2600, but fmc address decoding unit is 512kb.
Introduce seg_to_reg and reg_to_seg handlers for ast1030 fmc controller.
In addition, add ast1030 fmc, spi1, and spi2 class init handler.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-3-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per ast1030_v7.pdf, AST1030 ADC engine is identical to AST2600's ADC.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-2-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Guest code (u-boot) pokes at this on boot. No functionality is required
for guest code to work correctly, but it helps to document the region
being read from.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220318092211.723938-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to correctly report secure boot running firmware, these values
must be set. They are taken from a running machine when secure boot is
enabled.
We don't yet have documentation from ASPEED on what they mean. Set the
raw values for now, and in the future improve the model with properties
to set these on a per-machine basis.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220310052159.183975-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2600 clkin is always 25MHz, introduce clkin_25Mhz attribute
for aspeed_scu_get_clkin() to return the correct clkin for ast2600.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220315075753.8591-3-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
zhenwei pi