Re add point sampler to OpenGL. Fixes graphical issues when
Allow 8-bit textures is enabled on AMD gpus.
Issue: https://forums.pcsx2.net/Thread-GSDX-Hardware-mode-Bug-Report-Allow-8-bit-Texture
Adjust the code to be easier to read, and execute the gl code only on amd - suggested by Gregory.
Remove useless ATI_SUCKS define in tfx shader.It wasn't used anywhere outside of the shader.
Texture Shuffle changes:
Always Enable Texture shuffle on D3D10/11.
Previously Texture shuffle was enabled if CRC hack
level was below Full, this was kinda not good since
D3D also relies on CRC hacks on Full so you could either
stick with texture shuffle or crc hacks.
Texture shuffle is not supported on D3D9, however we can do a partial
port where instead of vertical lines with the effect we get the effect
on the entire screen. Better than nothing I suppose.
Ported some of the code from OpenGL to D3D
( just a copy - paste job :) ),
part of the code misses a dedicated shader but we can still
use it to fix various issues on many games.
List of affected games tested so far:
The Godfather, Final Fight Streetwise, The Suffering Ties that Bind,
Urban Chaos have their vertical lines issues fixed
(highly possible for other games as well), MGS and Stolen see an improvement
but they are still broken without crc hacks. Other games that suffered
similar issues are probably affected as well.
Channel Shuffle changes:
Update Channel Shuffle detection. A lot of games should see an improvement,
MGS, Urban Chaos, Stolen have their top left corner issues resolved.
Other games should be affected as well that use similar logic.
They still miss a shader so some effects are still broken/show glitches
but it's a nice improvement for D3D users.
Shared changes:
Texture Shuffle and Channel shuffle have been moved to their
own dedicated functions. Should make things a bit cleaner.
Move part of the code for Texture Shuffle to GSRendererHW to be shared
across all HW renderers, should aboid copy paste/duplicate code.
Move CRC hack to Partial that fix the half screen
bottom issue since the effect is not rendered correctly.
Move CRC hack to Aggressive. These hacks are only
needed when running upscaled resolution. They skip the
blur effect which cause ghosting and some other screen issues.
Side effect is they also remove the channel effect on OpenGL
which is emulated correctly so let's put them on Aggressive.
Comment out a hack, it's unknown what the hack does atm.
If there are new issues then it will be added back.
Added comments what the hacks do.
Partial port for channel shuffle effect to Direct3D for Tekken5.
The effect is skipped and not rendered but now the top left
screen glitch has been resolved.
Note: At least Minimum CRC level is required for this to work.
Adds merge sprite hack to GSDx hacks dialog
And ports merge sprite hack to Direct3D renderers.
Special thanks to my keyboards Ctrl, c and v buttons for all their hard
work in porting this hack.
Ports the "Unscale Point and Line" hack to the Direct3D11 Hardware renderer.
And enables the "Unscale Point and Line" hack for Custom Resolutions with Direct3D11 and OpenGL.
ICO uses a depth of field effect for the fog. Depth is extracted
into the alpha channel of a texture. And then used as blending factor.
You need a 1:1 texture/pixel mapping otherwise you will line at boundaries.
In order to extract the DoF, ICO moves the depth buffer around the GS
memory. Memory moves are implemented in the not-scaled world. It means
that we can't have the above 1:1 ratio. And we don't know anymore that
data are coming from the current depth buffer.
The solution: I reused an HLE channel shader to read the depth buffer directly.
This way I have the guarantee that pixel/depth are aligned.
Close#1816
Alpha test should only be disabled when writes to all of the alpha bits in the Framebuffer are masked. Fixes a regression in Dragon Ball Z: Budokai 3 scouter image rendering.
Bilinear applies to all renderer
* Common code done in GSVertexTrace
* Extend it with forced but sprite (trade-off between linear/upscale glitches)
* Linux GUI option was moved at the top with the renderer selection
Trilinear is moved to OGL hack
close#1837
Thanks to Flatout for the review and feedback.
It will take care to update the Window GUI :)
Mesa AMD was updated :)
all drivers[1] that support GL_ARB_shader_image_load_store got GL_ARB_clear_texture
[1] Intel driver misses others extensions to run GSdx
The previous implementation of HPO adds an offset on vertex position. It
doesn't always work beside it moves the rendering window.
The new implementation will add a texture offset so that instead to sample
the middle of the GS texel, we will sample the middle of the real texture texel.
It must be manually enabled with
* UserHacks_HalfPixelOffset_New = 1 (keep a small offset as intended by GS effect)
* UserHacks_HalfPixelOffset_New = 2 (no offset)
v2: always apply a 0.5 offset in case of float coordinates (Tales of Abyss)
Might break other games but few of them uses float coordinates to read
back the target
mipmap option 3. Actually maybe a separate tri-linear option will be better
m_mipmap == 2 => use manual PS2 trilinear/mipmap
Otherwise
m_filter == 3 => always use full automatic trilinear interpolation
m_filter == 4 => use automatic trilinear interpolation when PS2 uses mipmap
m_filter == 5 => like 4 but force bilinear interpolation inside layer
* As sw renderer, don't bother to bypass it when it is ATST_ALWAYS
* Don't update the ATE register value
=> It is a really bad idea. Next draw call will be wrong if TEST register isn't written.
The TryAlphaTest context could have been updated
gsdx ogl: only use geometry shader to convert big enough draw call
The purpose of geometry shader is to reduce bandwidth (72 bytes by sprite)
and CPU load.
Unfortunately it increases CPU load due to extra shader validations.
So geometry shader will only be enabled for draw call with more than
16 sprites (arbitrarily, smallest number before shadow hearts plummet)
v2: don't disable geometry shader in replayer.
It is easier to spot sprite rendering and to manually read vertex info.
Strangely the game uses large texture to handle texture buffer.
I think it plays with WMS/WMT. I'm not sure texture shuffling is 100%
correct here. But without it, it's completely broken.
* 0x9C712FF0, Jak1, EU
* 0x472E7699, Jak1, US
* 0x2479F4A9, Jak2, EU
* 0x12804727, Jak3, EU
* 0xDF659E77, JakX, EU
Please report me the CRC of the US version too so I can add them.
Please test the shadows rendering (openGL HW + accurate blending at least basic)
The game sets the framebuffer as an input texture. So I did the same for
openGL. Code is protected with a CRC. It is working because the game want to sample
pixels.
For the record, I tested it GTA too, it doesn't work as expected because
the game will resize the framebuffer to a smaller one. So you don't have
the guarantee that pixel will be read before a data write.
Note: it requires at least accurate blending set on basic
Note: I need CRC of all Jak games that suffers of this issue. Thanks you :)
Jonathan Li