* Change names to something less ludicrously verbose
* Now that we have QOM subclasses for the different DRC types, use a QOM
typename instead of a PAPR type value parameter
The latter allows removal of the get_type_shift() helper.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Acked-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Currently we only have a single QOM type for all DRCs, but lots of
places where we switch behaviour based on the DRC's PAPR defined type.
This is a poor use of our existing type system.
So, instead create QOM subclasses for each PAPR defined DRC type. We
also introduce intermediate subclasses for physical and logical DRCs,
a division which will be useful later on.
Instead of being stored in the DRC object itself, the PAPR type is now
stored in the class structure. There are still many places where we
switch directly on the PAPR type value, but this at least provides the
basis to start to remove those.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Acked-by: Michael Roth <mdroth@linux.vnet.ibm.com>
These two methods only have one implementation, and the spec they're
implementing means any other implementation is unlikely, verging on
impossible.
So replace them with simple functions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Tested-by: Daniel Barboza <danielhb@linux.vnet.ibm.com>
DRConnectorClass has a set_configured method, however:
* There is only one implementation, and only ever likely to be one
* There's exactly one caller, and that's (now) local
* The implementation is very straightforward
So abolish the method entirely, and just open-code what we need.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Daniel Barboza <danielhb@linux.vnet.ibm.com>
The DRConnectorClass includes a get_fdt method. However
* There's only one implementation, and there's only likely to ever be one
* Both callers are local to spapr_drc
* Each caller only uses one half of the actual implementation
So abolish get_fdt() entirely, and just open-code what we need.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Daniel Barboza <danielhb@linux.vnet.ibm.com>
The pointer drc->detach_cb is being used as a way of informing
the detach() function inside spapr_drc.c which cb to execute. This
information can also be retrieved simply by checking drc->type and
choosing the right callback based on it. In this context, detach_cb
is redundant information that must be managed.
After the previous spapr_lmb_release change, no detach_cb_opaques
are being used by any of the three callbacks functions. This is
yet another information that is now unused and, on top of that, can't
be migrated either.
This patch makes the following changes:
- removal of detach_cb_opaque. the 'opaque' argument was removed from
the callbacks and from the detach() function of sPAPRConnectorClass. The
attribute detach_cb_opaque of sPAPRConnector was removed.
- removal of detach_cb from the detach() call. The function pointer
detach_cb of sPAPRConnector was removed. detach() now uses a
switch(drc->type) to execute the apropriate callback. To achieve this,
spapr_core_release, spapr_lmb_release and spapr_phb_remove_pci_device_cb
callbacks were made public to be visible inside detach().
Signed-off-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If, once the kernel has booted, we try to remove a memory
hotplugged while the kernel was not started, QEMU crashes on
an assert:
qemu-system-ppc64: hw/virtio/vhost.c:651:
vhost_commit: Assertion `r >= 0' failed.
...
#4 in vhost_commit
#5 in memory_region_transaction_commit
#6 in pc_dimm_memory_unplug
#7 in spapr_memory_unplug
#8 spapr_machine_device_unplug
#9 in hotplug_handler_unplug
#10 in spapr_lmb_release
#11 in detach
#12 in set_allocation_state
#13 in rtas_set_indicator
...
If we take a closer look to the guest kernel log, we can see when
we try to unplug the memory:
pseries-hotplug-mem: Attempting to hot-add 4 LMB(s)
What happens:
1- The kernel has ignored the memory hotplug event because
it was not started when it was generated.
2- When we hot-unplug the memory,
QEMU starts to remove the memory,
generates an hot-unplug event,
and signals the kernel of the incoming new event
3- as the kernel is started, on the QEMU signal, it reads
the event list, decodes the hotplug event and tries to
finish the hotplugging.
4- QEMU receive the the hotplug notification while it
is trying to hot-unplug the memory. This moves the memory
DRC to an invalid state
This patch prevents this by not allowing to set the allocation
state to USABLE while the DRC is awaiting release.
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1432382
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
If a CPU is hot removed while hotplug of the same is still in progress,
the guest crashes. Prevent this by ensuring that detach is done only
after attach has completed.
The existing code already prevents such race for PCI hotplug. However
given that CPU is a logical DR unlike PCI and starts with ISOLATED
state, we need a logic that works for CPU too.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[Don't set awaiting_attach for PCI devices]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently spapr doesn't support "aborting" hotplug of PCI
devices by allowing device_del to immediately remove the
device if we haven't signalled the presence of the device
to the guest.
In the past this wasn't an issue, since we always immediately
signalled device attach and simply relied on full guest-aware
add->remove path for device removal. However, as of 788d259,
we now defer signalling for PCI functions until function 0
is attached, so now we need to deal with these "abort" operations
for cases where a user hotplugs a non-0 function, then opts to
remove it prior hotplugging function 0. Currently they'd have to
reboot before the unplug completed. PCIe multifunction hotplug
does not have this requirement however, so from a management
implementation perspective it would be good to address this within
the same release as 788d259.
We accomplish this by simply adding a 'signalled' flag to track
whether a device hotplug event has been sent to the guest. If it
hasn't, we allow immediate removal under the assumption that the
guest will not be using the device. Devices present at boot/reset
time are also assumed to be 'signalled'.
For CPU/memory/etc, signalling will still happen immediately
as part of device_add, so only PCI functions should be affected.
Cc: bharata@linux.vnet.ibm.com
Cc: david@gibson.dropbear.id.au
Cc: sbhat@linux.vnet.ibm.com
Cc: qemu-ppc@nongnu.org
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[dwg: This fixes a regression where an incorrect hot-add of a non-zero
function can no longer be backed out until function 0 is added]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Certain methods in sPAPRDRConnector objects are only ever called by
RTAS and in many cases are responsible for the logic that determines
the RTAS return codes.
Rather than having a level of indirection requiring RTAS code to
re-interpret return values from such methods to determine the
appropriate return code, just pass them through directly.
This requires changing method return types to uint32_t to match the
type of values currently passed to RTAS helpers.
In the case of read accesses like drc->entity_sense() where we weren't
previously reporting any errors, just the read value, we modify the
function to return RTAS return code, and pass the read value back via
reference.
Suggested-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If drmgr is used in the guest to hotplug a device before a device_add
has been issued via the QEMU monitor, QEMU segfaults in configure_connector
call. This occurs due to accessing of NULL FDT which otherwise would have
been created and associated with the DRC during device_add command.
Check for NULL FDT and return failure from configure_connector call.
As per PAPR+, an error value of -9003 seems appropriate for this failure.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function handles generation of ibm,drc-* array device tree
properties to describe DRC topology to guests. This will by used
by the guest to direct RTAS calls to manage any dynamic resources
we associate with a particular DR Connector as part of
hotplug/unplug.
Since general management of boot-time device trees are handled
outside of sPAPRDRConnector, we insert these values blindly given
an FDT and offset. A mask of sPAPRDRConnector types is given to
instruct us on what types of connectors entries should be generated
for, since descriptions for different connectors may live in
different parts of the device tree.
Based on code originally written by Nathan Fontenot.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This device emulates a firmware abstraction used by pSeries guests to
manage hotplug/dynamic-reconfiguration of host-bridges, PCI devices,
memory, and CPUs. It is conceptually similar to an SHPC device,
complete with LED indicators to identify individual slots to physical
physical users and indicate when it is safe to remove a device. In
some cases it is also used to manage virtualized resources, such a
memory, CPUs, and physical-host bridges, which in the case of pSeries
guests are virtualized resources where the physical components are
managed by the host.
Guests communicate with these DR Connectors using RTAS calls,
generally by addressing the unique DRC index associated with a
particular connector for a particular resource. For introspection
purposes we expose this state initially as QOM properties, and
in subsequent patches will introduce the RTAS calls that make use of
it. This constitutes to the 'guest' interface.
On the QEMU side we provide an attach/detach interface to associate
or cleanup a DeviceState with a particular sPAPRDRConnector in
response to hotplug/unplug, respectively. This constitutes the
'physical' interface to the DR Connector.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
David Gibson