For each Monitor, add one field "use_io_thr" to show whether it will be
using the dedicated monitor IO thread to handle input/output. When set,
monitor IO parsing work will be offloaded to the dedicated monitor IO
thread, rather than the original main loop thread.
This only works for QMP. HMP will always be run on the main loop
thread.
Currently we're still keeping use_io_thr off always. Will turn it on
later at some point.
One thing to mention is that we cannot set use_io_thr for every QMP
monitor. The problem is that MUXed typed chardevs may not work well
with it now. When MUX is used, frontend of chardev can be the monitor
plus something else. The only thing we know would be safe to be run
outside main thread so far is the monitor frontend. All the rest of the
frontends should still be run in main thread only.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-10-peterx@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: squash in Peter's followup patch to avoid test failures]
Signed-off-by: Eric Blake <eblake@redhat.com>
It was QLIST. I want to use this list to do monitor priority job later,
which need tail insertion ability. So switching to a tail queue.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-9-peterx@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
There are many places where the monitor initializes its globals:
- monitor_init_qmp_commands() at the very beginning
- single function to init monitor_lock
- in the first entry of monitor_init() using "is_first_init"
Unify them a bit.
monitor_lock is not used before monitor_init() (as confirmed by code
analysis and gdb watchpoints); so we are safe delaying what was a
constructor-time initialization of the mutex into the later first call
to monitor_init().
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-8-peterx@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
In monitor_qmp_read(), we have the hack to temporarily replace the
cur_mon pointer. Now we move this hack deeper inside the QMP dispatcher
routine since the Monitor pointer can be actually obtained using
container_of() upon the parser object, just like most of the other JSON
parser users do.
This does not make much sense as a single patch. However, this will be
a big step for the next patch, when the QMP dispatcher routine will be
split from the QMP parser.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-7-peterx@redhat.com>
[eblake: rebase context of qobject_to() macro]
Signed-off-by: Eric Blake <eblake@redhat.com>
It's part of the data init. Collect it.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-6-peterx@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
We can simplify object_property_get_str() using the new
qobject_get_try_str().
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-5-peterx@redhat.com>
[eblake: rebase context of qobject_to() macro]
Signed-off-by: Eric Blake <eblake@redhat.com>
A quick way to fetch string from qobject when it's a QString.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-4-peterx@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: rebase to qobject_to() macro]
Signed-off-by: Eric Blake <eblake@redhat.com>
The only difference from qstring_get_str() is that it allows the qstring
to be NULL. If so, NULL is returned.
CC: Eric Blake <eblake@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-3-peterx@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Update both the developer and spec for the new QMP OOB (Out-Of-Band)
command.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-2-peterx@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
TLS handshake may create background GSource tasks, while we won't know
the correct GMainContext until the whole chardev (including frontend)
inited. Let's postpone the initial TLS handshake until machine done.
For dynamically created tcp chardev, we don't postpone that by checking
the init_machine_done variable.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
[peterx: add missing include line, do unit test]
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180308140714.28906-1-peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
We have a clear replacement, so let's deprecate it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20180224154033.29559-8-mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Instead of converting all "backing": null instances into "backing": "",
handle a null value directly in bdrv_open_inherit().
This enables explicitly null backing links for json:{} filenames.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20180224154033.29559-7-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: rebase to qobject_to() parameter order and qapi headers split]
Signed-off-by: Eric Blake <eblake@redhat.com>
This patch reworks some places which use either qobject_type() checks
plus qobject_to(), where the latter alone is sufficient, or NULL checks
plus qobject_type() checks where we can simply do a qobject_to() != NULL
check.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20180224154033.29559-6-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: rebase to qobject_to() parameter ordering]
Signed-off-by: Eric Blake <eblake@redhat.com>
They are no longer needed now.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20180224154033.29559-5-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
This patch was generated using the following Coccinelle script:
@@
expression Obj;
@@
(
- qobject_to_qnum(Obj)
+ qobject_to(QNum, Obj)
|
- qobject_to_qstring(Obj)
+ qobject_to(QString, Obj)
|
- qobject_to_qdict(Obj)
+ qobject_to(QDict, Obj)
|
- qobject_to_qlist(Obj)
+ qobject_to(QList, Obj)
|
- qobject_to_qbool(Obj)
+ qobject_to(QBool, Obj)
)
and a bit of manual fix-up for overly long lines and three places in
tests/check-qjson.c that Coccinelle did not find.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20180224154033.29559-4-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: swap order from qobject_to(o, X), rebase to master, also a fix
to latent false-positive compiler complaint about hw/i386/acpi-build.c]
Signed-off-by: Eric Blake <eblake@redhat.com>
This is a dynamic casting macro that, given a QObject type, returns an
object as that type or NULL if the object is of a different type (or
NULL itself).
The macro uses lower-case letters because:
1. There does not seem to be a hard rule on whether qemu macros have to
be upper-cased,
2. The current situation in qapi/qmp is inconsistent (compare e.g.
QINCREF() vs. qdict_put()),
3. qobject_to() will evaluate its @obj parameter only once, thus it is
generally not important to the caller whether it is a macro or not,
4. I prefer it aesthetically.
The macro parameter order is chosen with typename first for
consistency with other QAPI macros like QAPI_CLONE(), as well as
for legibility (read it as "qobject to" type "applied to" obj).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20180224154033.29559-3-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
[eblake: swap parameter order to list type first, avoid clang ubsan
warning on QOBJECT(NULL) and container_of(NULL,type,base)]
Signed-off-by: Eric Blake <eblake@redhat.com>
The raspi3 has AArch64 CPUs, which means that our smpboot
code for keeping the secondary CPUs in a pen needs to have
a version for A64 as well as A32. Without this, the
secondary CPUs go into an infinite loop of taking undefined
instruction exceptions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-10-peter.maydell@linaro.org
Now we have separate types for BCM2386 and BCM2387, we might as well
just hard-code the CPU type they use rather than having it passed
through as an object property. This then lets us put the initialization
of the CPU object in init rather than realize.
Note that this change means that it's no longer possible on
the command line to use -cpu to ask for a different kind of
CPU than the SoC supports. This was never a supported thing to
do anyway; we were just not sanity-checking the command line.
This does require us to only build the bcm2837 object on
TARGET_AARCH64 configs, since otherwise it won't instantiate
due to the missing cortex-a53 device and "make check" will fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-9-peter.maydell@linaro.org
The BCM2837 sets the Aff1 field of the MPIDR affinity values for the
CPUs to 0, whereas the BCM2836 uses 0xf. Set this correctly, as it
is required for Linux to boot.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-8-peter.maydell@linaro.org
The bcm2837 is pretty similar to the bcm2836, but it does have
some differences. Notably, the MPIDR affinity aff1 values it
sets for the CPUs are 0x0, rather than the 0xf that the bcm2836
uses, and if this is wrong Linux will not boot.
Rather than trying to have one device with properties that
configure it differently for the two cases, create two
separate QOM devices for the two SoCs. We use the same approach
as hw/arm/aspeed_soc.c and share code and have a data table
that might differ per-SoC. For the moment the two types don't
actually have different behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-7-peter.maydell@linaro.org
Our BCM2836 type is really a generic one that can be any of
the bcm283x family. Rename it accordingly. We change only
the names which are visible via the header file to the
rest of the QEMU code, leaving private function names
in bcm2836.c as they are.
This is a preliminary to making bcm283x be an abstract
parent class to specific types for the bcm2836 and bcm2837.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-6-peter.maydell@linaro.org
The TypeInfo and state struct for bcm2386 disagree about what the
parent class is -- the TypeInfo says it's TYPE_SYS_BUS_DEVICE,
but the BCM2386State struct only defines the parent_obj field
as DeviceState. This would have caused problems if anything
actually tried to treat the object as a TYPE_SYS_BUS_DEVICE.
Fix the TypeInfo to use TYPE_DEVICE as the parent, since we don't
need any of the additional functionality TYPE_SYS_BUS_DEVICE
provides.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-5-peter.maydell@linaro.org
If we're directly booting a Linux kernel and the CPU supports both
EL3 and EL2, we start the kernel in EL2, as it expects. We must also
set the SCR_EL3.HCE bit in this situation, so that the HVC
instruction is enabled rather than UNDEFing. Otherwise at least some
kernels will panic when trying to initialize KVM in the guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180313153458.26822-4-peter.maydell@linaro.org
Add some assertions that if we're about to boot an AArch64 kernel,
the board code has not mistakenly set either secure_boot or
secure_board_setup. It doesn't make sense to set secure_boot,
because all AArch64 kernels must be booted in non-secure mode.
It might in theory make sense to set secure_board_setup, but
we don't currently support that, because only the AArch32
bootloader[] code calls this hook; bootloader_aarch64[] does not.
Since we don't have a current need for this functionality, just
assert that we don't try to use it. If it's needed we'll add
it later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-3-peter.maydell@linaro.org
For the rpi1 and 2 we want to boot the Linux kernel via some
custom setup code that makes sure that the SMC instruction
acts as a no-op, because it's used for cache maintenance.
The rpi3 boots AArch64 kernels, which don't need SMC for
cache maintenance and always expect to be booted non-secure.
Don't fill in the aarch32-specific parts of the binfo struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-2-peter.maydell@linaro.org
Add support for "TX complete"/TXDC interrupt generate by real HW since
it is needed to support guests other than Linux.
Based on the patch by Bill Paul as found here:
https://bugs.launchpad.net/qemu/+bug/1753314
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: Bill Paul <wpaul@windriver.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bill Paul <wpaul@windriver.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Message-id: 20180315191141.6789-2-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Code of imx_update() is slightly confusing since the "flags" variable
doesn't really corespond to anything in real hardware and server as a
kitchensink accumulating events normally reported via USR1 and USR2
registers.
Change the code to explicitly evaluate state of interrupts reported
via USR1 and USR2 against corresponding masking bits and use the to
detemine if IRQ line should be asserted or not.
NOTE: Check for UTS1_TXEMPTY being set has been dropped for two
reasons:
1. Emulation code implements a single character FIFO, so this flag
will always be set since characters are trasmitted as a part of
the code emulating "push" into the FIFO
2. imx_update() is really just a function doing ORing and maksing
of reported events, so checking for UTS1_TXEMPTY should happen,
if it's ever really needed should probably happen outside of
it.
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: Bill Paul <wpaul@windriver.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Message-id: 20180315191141.6789-1-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For guest kernel that supports KASLR, the load address can change every
time when guest VM runs. To find the physical base address correctly,
current QEMU dump searches VMCOREINFO for the string "NUMBER(phys_base)=".
However this string pattern is only available on x86_64. AArch64 uses a
different field, called "NUMBER(PHYS_OFFSET)=". This patch makes sure
QEMU dump uses the correct string on AArch64.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1520615003-20869-1-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sabrelite machine model used by qemu-system-arm is based on the
Freescale/NXP i.MX6Q processor. This SoC has an on-board ethernet
controller which is supported in QEMU using the imx_fec.c module
(actually called imx.enet for this model.)
The include/hw/arm/fsm-imx6.h file defines the interrupt vectors for the
imx.enet device like this:
#define FSL_IMX6_ENET_MAC_1588_IRQ 118
#define FSL_IMX6_ENET_MAC_IRQ 119
According to https://www.nxp.com/docs/en/reference-manual/IMX6DQRM.pdf,
page 225, in Table 3-1. ARM Cortex A9 domain interrupt summary,
interrupts are as follows.
150 ENET MAC 0 IRQ
151 ENET MAC 0 1588 Timer interrupt
where
150 - 32 == 118
151 - 32 == 119
In other words, the vector definitions in the fsl-imx6.h file are reversed.
Fixing the interrupts alone causes problems with older Linux kernels:
The Ethernet interface will fail to probe with Linux v4.9 and earlier.
Linux v4.1 and earlier will crash due to a bug in Ethernet driver probe
error handling. This is a Linux kernel problem, not a qemu problem:
the Linux kernel only worked by accident since it requested both interrupts.
For backward compatibility, generate the Ethernet interrupt on both interrupt
lines. This was shown to work from all Linux kernel releases starting with
v3.16.
Link: https://bugs.launchpad.net/qemu/+bug/1753309
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1520723090-22130-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
both do nothing as for the first all callers
parse_cpu_model() and qmp_query_cpu_model_()
should provide non NULL value, so just abort if it's not so.
While at it drop cpu_common_class_by_name() which is not need
any more as every target has CPUClass::class_by_name callback
by now, though abort in case a new arch will forget to define one.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1518013857-4372-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cpu_init(cpu_model) were replaced by cpu_create(cpu_type) so
no users are left, remove it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1518000027-274608-6-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
With all targets defining CPU_RESOLVING_TYPE, refactor
cpu_parse_cpu_model(type, cpu_model) to parse_cpu_model(cpu_model)
so that callers won't have to know internal resolving cpu
type. Place it in exec.c so it could be called from both
target independed vl.c and *-user/main.c.
That allows us to stop abusing cpu type from
MachineClass::default_cpu_type
as resolver class in vl.c which were confusing part of
cpu_parse_cpu_model().
Also with new parse_cpu_model(), the last users of cpu_init()
in null-machine.c and bsd/linux-user targets could be switched
to cpu_create() API and cpu_init() API will be removed by
follow up patch.
With no longer users left remove MachineState::cpu_model field,
new code should use MachineState::cpu_type instead and
leave cpu_model parsing to generic code in vl.c.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1518000027-274608-5-git-send-email-imammedo@redhat.com>
[ehabkost: Fix bsd-user build error]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will be used for providing to cpu name resolving class for
parsing cpu model for system and user emulation code.
Along with change add target to null-machine tests, so
that when switch to CPU_RESOLVING_TYPE happens,
it would ensure that null-machine usecase still works.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu> (m68k)
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> (tricore)
Message-Id: <1518000027-274608-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Added macro to riscv too]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
_Static_assert() allows us to specify messages, and that may come in
handy. Even without _Static_assert(), encouraging developers to put a
helpful message next to the QEMU_BUILD_BUG_* may make debugging easier
whenever it breaks.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20180224154033.29559-2-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Replace the generated json string with a literal qobject. The later is
easier to deal with, at run time as well as compile time: adding #if
conditionals will be easier than in a json string.
The output of query-qmp-schema is not changed.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180305172951.2150-5-marcandre.lureau@redhat.com>
[eblake: fix python 3 failure]
Signed-off-by: Eric Blake <eblake@redhat.com>
Instantiate a QObject* from a literal QLitObject.
LitObject only supports int64_t for now. uint64_t and double aren't
implemented.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180305172951.2150-4-marcandre.lureau@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
CentOS 6 lacks a realpath binary on the base install, which makes
all iotests runs fail since the 2.11 release:
001 - output mismatch (see 001.out.bad)
./check: line 815: realpath: command not found
diff: missing operand after `/home/dummy/qemu/tests/qemu-iotests/001.out'
diff: Try `diff --help' for more information.
Many of the uses of 'realpath' in the check script were being
used on the output of 'type -p' - but that is already an
absolute file name. While a canonical name can often be
shorter (realpath gets rid of /../), it can also be longer (due
to symlink expansion); and we really don't care if the name is
canonical, merely that it was an executable file with an
absolute path. These were broken in commit cceaf1db.
The remaining use of realpath was to convert a possibly relative
filename into an absolute one before calling diff to make it
easier to copy-and-paste the filename for moving the .bad file
into place as the new reference file even when running iotests
out-of-tree (see commit 93e53fb6), but $PWD can achieve the same
purpose.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit bff5554843 added "force_size" into the common.filter for
_filter_img_create(), but test 146 still expects it in the output.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This fails in Fedora 28.
Reported-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Overriding flags violates the precedence rules of
bdrv_reopen_queue_child. Just like the read-only option, no-flush should
be put into the options. The same is done in bdrv_temp_snapshot_options.
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When doing drive mirror to a low speed shared storage, if there was heavy
BLK IO write workload in VM after the 'ready' event, drive mirror block job
can't be canceled immediately, it would keep running until the heavy BLK IO
workload stopped in the VM.
Libvirt depends on the current block-job-cancel semantics, which is that
when used without a flag after the 'ready' event, the command blocks
until data is in sync. However, these semantics are awkward in other
situations, for example, people may use drive mirror for realtime
backups while still wanting to use block live migration. Libvirt cannot
start a block live migration while another drive mirror is in progress,
but the user would rather abandon the backup attempt as broken and
proceed with the live migration than be stuck waiting for the current
drive mirror backup to finish.
The drive-mirror command already includes a 'force' flag, which libvirt
does not use, although it documented the flag as only being useful to
quit a job which is paused. However, since quitting a paused job has
the same effect as abandoning a backup in a non-paused job (namely, the
destination file is not in sync, and the command completes immediately),
we can just improve the documentation to make the force flag obviously
useful.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Reported-by: Huaitong Han <huanhuaitong@didichuxing.com>
Signed-off-by: Huaitong Han <huanhuaitong@didichuxing.com>
Signed-off-by: Liang Li <liliangleo@didichuxing.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Perform the rounding to match a CHS geometry only in the legacy code
path in .bdrv_co_create_opts. QMP now requires that the user already
passes a CHS aligned image size, unless force-size=true is given.
CHS alignment is required to make the image compatible with Virtual PC,
but not for use with newer Microsoft hypervisors.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This adds the .bdrv_co_create driver callback to vpc, which
enables image creation over QMP.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Peter Xu