Convert the pcnet-pci device away from using the old_mmio
MemoryRegionOps accessor functions.
This commit is a no-behaviour-change API conversion.
(Since PCNET_PNPMMIO_SIZE is 0x20, the old "addr & 0x10"
check and the new "addr < 0x10" check are exact opposites;
the new code is phrased to be parallel with the
pcnet_io_read/write functions.)
I have left a TODO comment marker because the similarity
between the MMIO and IO accessor behaviour is suspicious
and they could be combined, but this will be left to a
different patch.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GIC_BASE_IRQ macro is a leftover from when we shared code
between the GICv2 and the v7M NVIC. Since the NVIC is now
split off, GIC_BASE_IRQ is always 0, and we can just delete it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180824161819.11085-1-peter.maydell@linaro.org
The event queue management is broken today. Event records
are not properly written as EVT_SET_* macro was not updating
the actual event record. Also the event queue interrupt
is not correctly triggered.
Fixes: bb981004ea ("hw/arm/smmuv3: Event queue recording helper")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180921070138.10114-3-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a long story. Red Hat has relicensed Windows KVM device drivers
in 2018 and there was an agreement that to avoid WHQL driver conflict
software manufacturers should set proper PCI subsystem vendor ID in
their distributions. Thus PCI subsystem vendor id becomes actively used.
The problem is that this field is applied by us via hardware compats.
Thus technically it could be lost.
This patch adds PCI susbsystem id and vendor id to exportable parameters
for validation.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180918095852.28422-1-den@openvz.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
At the point smmu_find_add_as() gets called, the bus number might
not be computed. Let's change the name of IOMMU memory region and
just use the devfn and an incrementing index.
The name only is used for debug.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180921070138.10114-2-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: changed 'uint' to 'unsigned int']
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 datasheet says:
I2CD10 Interrupt Status Register
bit 2 Receive Done Interrupt status
S/W needs to clear this status bit to allow next data receiving
The Rx interrupt done interrupt status bit needs to be cleared
explicitly before the next byte can be received, and must therefore
not be auto-cleared. Also, receiving the next byte must be delayed
until the bit has been cleared.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Receive command handling may have to be deferred if a previous receive
done interrupt was not yet acknowledged. Move receive command handling
into a separate function to prepare for the necessary changes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-3-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
aspeed i2c interrupts should be cleared by software only, and the bus
interrupt should be lowered when all interrupts have been cleared.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180914063506.20815-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop TODO comment describing an issue which is
fixed later in the patch series, and clean up commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the base for a machine model of the BBC micro:bit:
https://en.wikipedia.org/wiki/Micro_Bit
This is a system with a nRF51 SoC containing the main processor, with
various peripherals on board.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180831220920.27113-4-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nRF51 is a Cortex-M0 microcontroller with an on-board radio module,
plus other common ARM SoC peripherals.
http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
This defines a basic model of the CPU and memory, with no peripherals
implemented at this stage.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180831220920.27113-3-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: wrapped a few long lines]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Like commit 16b4226(hw/acpi-build: Add a check for memory-less NUMA node
), it also needs to check memory length for NUMA nodes on ARM.
Signed-off-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180911112643.19296-1-shenglong.zsl@alibaba-inc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 97274d0c05 ("hw/char/exynos4210_uart.c: Remove unneeded
handling of NULL chardev") broke Exynos4210 support as it removed
NULL 'Chardev *chr' handling from exynos4210_uart_create() and
currently exynos4210_init() always passes NULL as 'Chardev *chr'
argument to exynos4210_uart_create() calls. Fix it by adding
missing serial_hd() calls to exynos4210_init().
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 9310418.Wg32kryeWE@amdc3058
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here are the accumulated ppc target patches for the last several
weeks. Highlights are:
* A number of 40p / PReP cleanups
* Preliminary irq rework on the pseries machine towards the new
XIVE interrupt controller
There are a few patches which make small changes to generic device and
arm code as prerequisites to the 40p interrupt routing cleanup. They
have acks from the relevant maintainers.
-----BEGIN PGP SIGNATURE-----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=A62f
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180925' into staging
ppc patch queue 2018-09-25
Here are the accumulated ppc target patches for the last several
weeks. Highlights are:
* A number of 40p / PReP cleanups
* Preliminary irq rework on the pseries machine towards the new
XIVE interrupt controller
There are a few patches which make small changes to generic device and
arm code as prerequisites to the 40p interrupt routing cleanup. They
have acks from the relevant maintainers.
# gpg: Signature made Tue 25 Sep 2018 08:00:06 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180925:
40p: add fixed IRQ routing for LSI SCSI device
lsi53c895a: add optional external IRQ via qdev
scsi: remove unused lsi53c895a_create() and lsi53c810_create() functions
scsi: move lsi53c8xx_create() callers to lsi53c8xx_handle_legacy_cmdline()
scsi: add lsi53c8xx_handle_legacy_cmdline() function
sm501: Adjust endianness of pixel value in rectangle fill
spapr_pci: add an extra 'nr_msis' argument to spapr_populate_pci_dt
spapr: increase the size of the IRQ number space
spapr: introduce a spapr_irq class 'nr_msis' attribute
40p: use OR gate to wire up raven PCI interrupts
raven: some minor IRQ-related tidy-ups
hw/ppc: on 40p machine, change default firmware to OpenBIOS
target/ppc/cpu-models: Re-group the 970 CPUs together again
Record history of ppcemb target in common.json
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Whilst the PReP specification describes how all PCI IRQs are routed via IRQ
15 on the interrupt controller, the real 40p machine has a routing quirk in
that the LSI SCSI device is routed directly to IRQ 13.
Enable the external IRQ for the LSI SCSI device by wiring up the IRQ with
qdev to the relevant interrupt controller gpio.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On some early machines the on-board PCI devices IRQs are wired directly to
the interrupt controller instead of via the PCI host bridge.
Add an optional external IRQ that if wired up via qdev will replace the
in-built PCI IRQ.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that these functions are no longer required they can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As part of commits a64aa5785d "hw: Deprecate -drive if=scsi with non-onboard
HBAs" and b891538e81 "hw/ppc/prep: Fix implicit creation of "-drive if=scsi"
devices" the lsi53c895a_create() and lsi53c810_create() functions were added
to wrap pci_create_simple() and scsi_bus_legacy_handle_cmdline().
Unfortunately this prevents us from changing qdev properties on the device
and/or changing the PCI configuration. By switching over to using the new
lsi53c8xx_handle_legacy_cmdline() function then the caller can now configure
and realize the LSI SCSI device exactly as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org> [arm parts]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the function that will soon be used to replace lsi53c895a_create() and
lsi53c810_create().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The value from twoD_foreground (which is in host endian format) must
be converted to the endianness of the framebuffer (currently always
little endian) before it can be used to perform the fill operation.
Signed-off-by: Marcus Comstedt <marcus@mc.pp.se>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
So that we don't have to call qdev_get_machine() to get the machine
class and the sPAPRIrq backend holding the number of MSIs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The new layout using static IRQ number does not leave much space to
the dynamic MSI range, only 0x100 IRQ numbers. Increase the total
number of IRQS for newer machines and introduce a legacy XICS backend
for pre-3.1 machines to maintain compatibility.
For the old backend, provide a 'nr_msis' value covering the full IRQ
number space as it does not use the bitmap allocator to allocate MSI
interrupt numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The number of MSI interrupts a sPAPR machine can allocate is in direct
relation with the number of interrupts of the sPAPRIrq backend. Define
statically this value at the sPAPRIrq class level and use it for the
"ibm,pe-total-#msi" property of the sPAPR PHB.
According to the PAPR specs, "ibm,pe-total-#msi" defines the maximum
number of MSIs that are available to the PE. We choose to advertise
the maximum number of MSIs that are available to the machine for
simplicity of the model and to avoid segmenting the MSI interrupt pool
which can be easily shared. If the pool limit is reached, it can be
extended dynamically.
Finally, remove XICS_IRQS_SPAPR which is now unused.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the PReP specification section 6.1.6 "System Interrupt
Assignments", all PCI interrupts are routed via IRQ 15.
Instead of mapping each PCI IRQ separately, we introduce an OR gate within the
raven PCI host bridge and then wire the single output of the OR gate to the
interrupt controller.
Note that whilst the (now deprecated) PReP machine still exists we still need
to preserve the old IRQ routing. This is done by adding a new "is-legacy-prep"
property to the raven PCI host bridge which is set to true for the PReP
machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This really lays the groundwork for the upcoming patches: it renames the
irqs PREPPCIState struct member to pci_irqs (as soon there will be a
distinction) and then changes the raven IRQ opaque to use PREPPCIState
instead of just irqs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
OpenBIOS gained 40p support in 5b20e4cace
Use it, instead of relying on an unmaintained and very limited firmware.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
-----BEGIN PGP SIGNATURE-----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=WnE4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180907' into staging
ppc patch queue 2018-09-07
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
# gpg: Signature made Fri 07 Sep 2018 08:30:02 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180907:
target-ppc: Extend HWCAP2 bits for ISA 3.0
target/ppc/kvm: set vcpu as online/offline
Fix a deadlock case in the CPU hotplug flow
spapr: Correct reference count on spapr-cpu-core
mac_newworld: implement custom FWPathProvider
uninorth: add ofw-addr property to allow correct fw path generation
mac_oldworld: implement custom FWPathProvider
grackle: set device fw_name and address for correct fw path generation
macio: add addr property to macio IDE object
macio: add macio bus to help with fw path generation
macio: move MACIOIDEState type declarations to macio.h
spapr_pci: fix potential NULL pointer dereference
spapr: fix leak of rev array
ppc: Remove deprecated ppcemb target
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAluQU38ACgkQIeENKd+X
cFRAXQgAlhNcwby+Jsk8sbLajMWXEtww9FIv+XESldPOJHmJyCkNDVZX8MuMM7+f
8NraD3YGDJvXP/BEcmyE5yPC6mx+OIi8ufzqP0rUML1x4+Tpxp8nZ7sBH197RtGg
eImPA6oKvg4wyfNOrZ+hGa8HF/iMT03TqeKggUPf3dVAs8LV2iUwBIzrRLB4IhIN
yFnhbcw8cW04tWUhYg4+viDY2k0q7fMrJZkASD/RjGMBjubJkwWvSYOdMIEWSpcG
2qLT5SohzUzHyKPONsoBKjSIP+nKgtyYR6IJh40FDd5S5RRMHe/n3q9jChIkHMma
x1eSNvVd41++QlBKqDeAlA+gbdK/uw==
=FJn/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-pullreq-20180905' into staging
A misc collection of RISC-V related patches for 3.1.
# gpg: Signature made Wed 05 Sep 2018 23:06:55 BST
# gpg: using RSA key 21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-pullreq-20180905:
riscv: remove define cpu_init()
hw/riscv/spike: Set the soc device tree node as a simple-bus
hw/riscv/virtio: Set the soc device tree node as a simple-bus
target/riscv: call gen_goto_tb on DISAS_TOO_MANY
target/riscv: optimize indirect branches
target/riscv: optimize cross-page direct jumps in softmmu
RISC-V: Simplify riscv_cpu_local_irqs_pending
RISC-V: Use atomic_cmpxchg to update PLIC bitmaps
RISC-V: Improve page table walker spec compliance
RISC-V: Update address bits to support sv39 and sv48
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
error_report and friends already add a "qemu-system-xxx" prefix
to the string, so a "qemu:" prefix is redundant in the string.
Just drop it.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1537495530-580-1-git-send-email-maozhongyi@cmss.chinamobile.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Add two functions to print an error/warning report once depending
on a passed-in condition variable and flip it if printed. This is
useful if you want to print a message not once-globally, but e.g.
once-per-device.
Inspired by warn_once() in hw/vfio/ccw.c, which has been replaced
with warn_report_once_cond().
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20180830145902.27376-2-cohuck@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Function comments reworded]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
- split off the individual virtio-ccw devices into separate files
-----BEGIN PGP SIGNATURE-----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=c1n9
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180829' into staging
- various fixes and improvements in the tcg code
- split off the individual virtio-ccw devices into separate files
# gpg: Signature made Wed 29 Aug 2018 10:38:03 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180829:
target/s390x: use regular spaces in translate.c
hw/s390x: Move virtio-ccw-blk code to a separate file
hw/s390x: Move virtio-ccw-net code to a separate file
hw/s390x: Move virtio-ccw-input code to a separate file
hw/s390x: Move virtio-ccw-gpu code to a separate file
hw/s390x: Move vhost-vsock-ccw code to a separate file
hw/s390x: Move virtio-ccw-crypto code to a separate file
hw/s390x: Move virtio-ccw-9p code to a separate file
hw/s390x: Move virtio-ccw-rng code to a separate file
hw/s390x: Move virtio-ccw-scsi code to a separate file
hw/s390x: Move virtio-ccw-balloon code to a separate file
hw/s390x: Move virtio-ccw-serial code to a separate file
hw/s390x/virtio-ccw: Consolidate calls to virtio_ccw_unrealize()
target/s390x: fix PACK reading 1 byte less and writing 1 byte more
target/s390x: add EX support for TRT and TRTR
target/s390x: fix IPM polluting irrelevant bits
target/s390x: fix CSST decoding and runtime alignment check
target/s390x: add BAL and BALR instructions
tests/tcg: add a simple s390x test
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
to allow the correct customisation of the disk node names as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Set the fw_name property to "pci" and also set an explicit OFW address
using the value of the special_base property.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
virtio_queue_get_desc_addr returns 64-bit hwaddr while int is usually 32-bit.
If returned hwaddr is not equal to 0 but least-significant 32 bits are
equal to 0 then this code will not actually stop running queue.
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Acked-by: Jia He <hejianet@gmail.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The first cpu unplug wasn't ever supported and corresponding
monitor/qmp commands refuse to unplug it. However guest is able
to issue eject request either using following command:
# echo 1 >/sys/devices/system/cpu/cpu0/firmware_node/eject
or directly writing to cpu hotplug registers, which makes
qemu crash with SIGSEGV following back trace:
kvm_flush_coalesced_mmio_buffer ()
while (ring->first != ring->last)
...
qemu_flush_coalesced_mmio_buffer
prepare_mmio_access
flatview_read_continue
flatview_read
address_space_read_full
address_space_rw
kvm_cpu_exec(cpu!0)
qemu_kvm_cpu_thread_fn
the reason for which is that ring == KVMState::coalesced_mmio_ring
happens to be a part of 1st CPU that was uplugged by guest.
Fix it by forbidding 1st cpu unplug from guest side and in addition
remove CPU0._EJ0 ACPI method to make clear that unplug of the first
CPU is not supported.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add hint to firmware (e.g. SeaBIOS) to reserve addtional
BUS/IO/MEM/PREF resource for legacy pci-pci bridge. Add the
resource reserve capability deleting in pci_bridge_dev_exitfn.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Factor "bus_reserve", "io_reserve", "mem_reserve", "pref32_reserve"
and "pref64_reserve" fields of the "GenPCIERootPort" structure out
to "PCIResReserve" structure, so that other PCI bridges can
reuse it to add resource reserve capability.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Because the cache is sized to include the rings and the event indices,
negotiating the VIRTIO_RING_F_EVENT_IDX feature will result in the size
of the cache changing. And because MemoryRegionCache accesses are
range-checked, if we skip this we end up with an assertion failure.
This happens with OpenBSD 6.3.
Reported-by: Fam Zheng <famz@redhat.com>
Fixes: 97cd965c07
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit
10efd7e108 "pc: acpi: fix memory hotplug regression by reducing stub SRAT entry size"
attemped to fix hotplug regression introduced by
848a1cc1e "hw/acpi-build: build SRAT memory affinity structures for DIMM devices"
fixed issue for Windows/3.0+ linux kernels, however it regressed 2.6 based
kernels (RHEL6) to the point where guest might crash at boot.
Reason is that 2.6 kernel discards SRAT table due too small last entry
which down the road leads to crashes. Hack I've tried in 10efd7e108 is also
not ACPI spec compliant according to which whole possible RAM should be
described in SRAT. Revert 10efd7e108 to fix regression for 2.6 based kernels.
With 10efd7e108 reverted, I've also tried splitting SRAT table statically
in different ways %/node and %/slot but Windows still fails to online
2nd pc-dimm hot-plugged into node 0 (as described in 10efd7e108) and
sometimes even coldplugged pc-dimms where affected with static SRAT
partitioning.
The only known so far way where Windows stays happy is when we have 1
SRAT entry in the last node covering all hotplug area.
Revert 848a1cc1e until we come up with a way to avoid regression
on Windows with hotplug area split in several entries.
Tested this with 2.6/3.0 based kernels (RHEL6/7) and WS20[08/12/12R2/16]).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To allow Linux to enumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Set the newly added register(KVM_REG_PPC_ONLINE) to indicate if the vcpu is
online(1) or offline(0)
KVM will use this information to set the RWMR register, which controls the PURR
and SPURR accumulation.
CC: paulus@samba.org
Signed-off-by: Nikunj A Dadhania <nikunj@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Switch from cpu_physical_memory_map to dma_memory_map,
so iommu mappings for virtio-gpu objects work properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180829122101.29852-3-kraxel@redhat.com>
No functional change, just preparation for a followup patch
which needs a VirtIOGPU pointer.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180829122101.29852-2-kraxel@redhat.com>
We need to set cs->halted to 1 before calling ppc_set_compat. The reason
is that ppc_set_compat kicks up the new thread created to manage the
hotplugged KVM virtual CPU and the code drives directly to KVM_RUN
ioctl. When cs->halted is 1, the code:
int kvm_cpu_exec(CPUState *cpu)
...
if (kvm_arch_process_async_events(cpu)) {
atomic_set(&cpu->exit_request, 0);
return EXCP_HLT;
}
...
returns before it reaches KVM_RUN, giving time to the main thread to
finish its job. Otherwise we can fall in a deadlock because the KVM
thread will issue the KVM_RUN ioctl while the main thread is setting up
KVM registers. Depending on how these jobs are scheduled we'll end up
freezing QEMU.
The following output shows kvm_vcpu_ioctl sleeping because it cannot get
the mutex and never will.
PS: kvm_vcpu_ioctl was triggered kvm_set_one_reg - compat_pvr.
STATE: TASK_UNINTERRUPTIBLE|TASK_WAKEKILL
PID: 61564 TASK: c000003e981e0780 CPU: 48 COMMAND: "qemu-system-ppc"
#0 [c000003e982679a0] __schedule at c000000000b10a44
#1 [c000003e98267a60] schedule at c000000000b113a8
#2 [c000003e98267a90] schedule_preempt_disabled at c000000000b11910
#3 [c000003e98267ab0] __mutex_lock at c000000000b132ec
#4 [c000003e98267bc0] kvm_vcpu_ioctl at c00800000ea03140 [kvm]
#5 [c000003e98267d20] do_vfs_ioctl at c000000000407d30
#6 [c000003e98267dc0] ksys_ioctl at c000000000408674
#7 [c000003e98267e10] sys_ioctl at c0000000004086f8
#8 [c000003e98267e30] system_call at c00000000000b488
crash> struct -x kvm.vcpus 0xc000003da0000000
vcpus = {0xc000003db4880000, 0xc000003d52b80000, 0xc0000039e9c80000, 0xc000003d0e200000, 0xc000003d58280000, 0x0, 0x0, ...}
crash> struct -x kvm_vcpu.mutex.owner 0xc000003d58280000
mutex.owner = {
counter = 0xc000003a23a5c881 <- flag 1: waiters
},
crash> bt 0xc000003a23a5c880
PID: 61579 TASK: c000003a23a5c880 CPU: 9 COMMAND: "CPU 4/KVM"
(active)
crash> struct -x kvm_vcpu.mutex.wait_list 0xc000003d58280000
mutex.wait_list = {
next = 0xc000003e98267b10,
prev = 0xc000003e98267b10
},
crash> struct -x mutex_waiter.task 0xc000003e98267b10
task = 0xc000003e981e0780
The following command-line was used to reproduce the problem (note: gdb
and trace can change the results).
$ qemu-ppc/build/ppc64-softmmu/qemu-system-ppc64 -cpu host \
-enable-kvm -m 4096 \
-smp 4,maxcpus=8,sockets=1,cores=2,threads=4 \
-display none -nographic \
-drive file=disk1.qcow2,format=qcow2
...
(qemu) device_add host-spapr-cpu-core,core-id=4
[no interaction is possible after it, only SIGKILL to take the terminal
back]
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This reverts commit 93f874fe9d.
Now with virtio-vga being resetted properly the
crash workaround is not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-3-kraxel@redhat.com
We must call the reset functions for both virtio-gpu
and vga to properly reset the combo device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-2-kraxel@redhat.com
spapr_init_cpus() currently creates spapr-cpu-core objects via
object_new() and setting their realized property to true. This leaves
their reference count at two, because object_new() adds an initial
reference and the realization attaches them to a default parent object
which also increments the reference count.
This causes a problem if one of these cores is hot unplugged: no
delete event is generated for it because it's reference count doesn't
reach zero when it is detached from it's parent.
Correct this by adding a call to object_unref() in spapr_init_cpus().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
since an additional disk node should not be added except for virtio devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
since an additional disk node should not be added except for virtio devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This contains the offset of the IDE controller within the macio address space
and is required to allow the address to be included within the fw path.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As the in-built IDE controller is attached to the macio bus then we should also
model this the same in QEMU to aid fw path generation.
Note that all existing macio devices are moved onto the new macio bus so that
the qdev tree accurately reflects the real hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The generated qapi_event_send_FOO() take an Error ** argument. They
can't actually fail, because all they do with the argument is passing it
to functions that can't fail: the QObject output visitor, and the
@qmp_emit callback, which is either monitor_qapi_event_queue() or
event_test_emit().
Drop the argument, and pass &error_abort to the QObject output visitor
and @qmp_emit instead.
Suggested-by: Eric Blake <eblake@redhat.com>
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815133747.25032-4-peterx@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message rewritten, update to qapi-code-gen.txt corrected]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_BLK has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532542110-9017-1-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_NET has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532542056-8927-1-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_INPUT has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-11-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_GPU has been set. This
can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-10-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VHOST_VSOCK has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-9-git-send-email-thuth@redhat.com>
[CH: updated MAINTAINERS]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_CRYPTO has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-8-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_9P and CONFIG_VIRTFS
have been set. This can be done best if the code resides in a separate
file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-7-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_RNG has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-6-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_SCSI has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-5-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_BALLOON has been
set. This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-4-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_SERIAL has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-3-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Currently, every virtio-ccw device explicitely sets its unrealize
function to virtio_ccw_unrealize() in its class_init function.
We can simplify this by using a common unrealize function, just like
it is already done for the realize functions.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-2-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 2c88b098e7 added a call to SPAPR_MACHINE_GET_CLASS(spapr) in
spapr_phb_realize() before we check spapr isn't NULL. This causes QEMU
to crash when starting a non-pseries machine with a sPAPR PHB.
This could be fixed by setting the smc variable after the null check,
but it seems more explicit to use a ternary operator to skip the call
to SPAPR_MACHINE_GET_CLASS() if spapr is NULL, since spapr_phb_realize()
will return immediately in this case.
This was reported by Coverity (CID 1395170 and 1395183).
Fixes: 2c88b098e7
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduced in 04d595b300 ("spapr: do not use CPU_FOREACH_REVERSE",
2018-08-23)
Fixes: CID1395181
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no known available OS for ppc around anymore that uses page
sizes below 4k, so it does not make much sense that we keep wasting
our time on building and testing the ppcemb-softmmu target. It has
been deprecated since two releases, and nobody complained, so let's
remove this now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace all the trace_vtd_err_*() hooks with the new error_report_once()
since they are similar to trace_vtd_err() - dumping the first error
would be mostly enough, then we have them on by default too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-4-peterx@redhat.com>
[Use "%x" instead of "%" PRIx16 to print uint16_t, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Replace existing trace_vtd_err() with error_report_once() then stderr
will capture something if any of the error happens, meanwhile we don't
suffer from any DDOS. Then remove the trace point. Since at it,
provide more information where proper (now we can pass parameters into
the report function).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-3-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[Two format strings fixed, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix passing argument for nanoMIPS bare metal related to the
semihosting regime.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Setup the GT64120 BARs in the nanoMIPS bootloader, in the same way that
they are setup in the MIPS32 bootloader. This is necessary for Linux to
be able to access peripherals, including the UART.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Paul Burton <pburton@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add basic nanoMIPS boot code for Malta.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
-----BEGIN PGP SIGNATURE-----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=2bke
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/check/20180822' into staging
check/next for 20180822
# gpg: Signature made Wed 22 Aug 2018 09:03:40 BST
# gpg: using RSA key F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/check/20180822:
check: Only test tpm devices when they are compiled in
check: Only test usb-ehci when it is compiled in
check: Only test usb-uhci devices when they are compiled in
check: Only test usb-ohci when it is compiled in
check: Only test nvme when it is compiled in
check: Only test pvpanic when it is compiled in
check: Only test wdt_ib700 when it is compiled in
check: Only test sdhci when it is compiled in
check: Only test i82801b11 when it is compiled in
check: Only test ioh3420 when it is compiled in
check: Only test ipack when it is compiled in
check: Only test hda when it is compiled in
check: Only test ac97 when it is compiled in
check: Only test es1370 when it is compiled in
check: Only test rtl8139 when it is compiled in
check: Only test pcnet when it is compiled in
check: Only test eepro100 when it is compiled in
check: Only test ne2000 when it is compiled in
check: Only test vmxnet3 when it is compiled in
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix MPS2 SCC config register values for the mps2-an511
and mps2-an385 boards:
* the SCC_AID bits [23:20] specify the FPGA build target board revision,
and the SCC_CFG4 register specifies the actual board revision, so
these should have matching values. Claim to be board revision C,
consistently -- we had the revision in the wrong part of SCC_AID.
* SCC_ID bits [15:4] should be the board number in hex, not decimal
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180823175225.22612-1-peter.maydell@linaro.org
Refactor bcm2835_fb_mbox_push() to work by calling
bcm2835_fb_validate_config() and bcm2835_fb_reconfigure(),
so that config set this way is also validated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-9-peter.maydell@linaro.org
Validate the config settings that the guest tries to set.
The wiki page documentation is not really accurate here:
generally rather than failing requests to set bad parameters,
the hardware will just clip them to something sensible.
Validate the most important parameters: sizes and
the viewport offsets. This prevents the framebuffer
code from trying to read out-of-range memory.
In the property handling code, we validate the new parameters every
time we encounter a tag that sets them. This means we validate the
config multiple times if the request includes multiple config-setting
tags, but the code would require significant restructuring to do a
validation only once but still return the clipped settings for
get-parameter tags and the buffer allocation tag.
Validation of settings made via the older bcm2835_fb_mbox_push()
function will be done in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-8-peter.maydell@linaro.org
The raspi framebuffir in bcm2835_fb supports the definition
of a virtual "viewport", which is smaller than the full
physical framebuffer size and at an adjustable offset within
it. Only the viewport area is sent to the screen. This allows
the guest to do things like double buffering, or scrolling
by adjusting the viewport origin. Currently QEMU doesn't
implement this at all.
Add support for this feature:
* the property mailbox code needs to distinguish the
virtual width/height from the physical width/height
* the framebuffer code needs to do something with the
virtual width/height/origin information
Note that the wiki documentation on the semantics of the
virtual and physical height and width has it the wrong way
around -- the virtual size is the size of the allocated
buffer, and the physical size is the size of the display,
so the virtual size is always the same as or larger than
the physical.
If the viewport size is set smaller than the physical
screen size, we ignore the viewport settings completely
and just display the physical screen area.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-7-peter.maydell@linaro.org
Abstract out the calculation of the pitch and size of the
framebuffer into functions that operate on the BCM2835FBConfig
struct -- these are about to get a little more complicated
when we add support for virtual and physical sizes differing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-6-peter.maydell@linaro.org
The bcm2835_fb's initial resolution and other parameters are set
via QOM properties. We should reset to those initial values on
device reset, which means we need to save the QOM property
values somewhere that they are not overwritten by guest
changes to the framebuffer configuration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-5-peter.maydell@linaro.org
The BCM2835FBState struct has a 'pitch' field which is a
cached copy of xres * (bpp >> 3), and a 'size' field which is
a cached copy of pitch * yres. However we don't actually do
anything with these fields; delete them. We retain the
now-unused slots in the VMState struct for migration
compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-4-peter.maydell@linaro.org
Refactor the fb property setting code so that rather than
using a set of pointers to local variables to track
whether a config value has been updated in the current
mbox and if so what its new value is, we just copy
all the current settings of the fb at the start, and
then update that copy as we go along, before asking
the fb to switch to it at the end.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-3-peter.maydell@linaro.org
The handling of framebuffer properties in the bcm2835_property code
is a bit clumsy, because for each of the many fb related properties
we try to track the value we're about to set and whether we're going
to be setting a value, and then we hand all the new values off
to the framebuffer via a function which takes them all as separate
arguments. It would be simpler if the property code could easily
copy all the framebuffer's current settings, update them with
the new specified values and then ask the framebuffer to switch
to the new set.
As the first part of this refactoring, pull all the fb config
settings fields in BCM2835FBState out into their own struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-2-peter.maydell@linaro.org
Some of the config register values we were setting for the MPS2 SCC
weren't correct:
* the SCC_AID bits [23:20] specify the FPGA build target board revision,
and the SCC_CFG4 register specifies the actual board revision, so
these should have matching values. Claim to be board revision C,
consistently -- we had the revision in the wrong part of SCC_AID.
* SCC_ID bits [15:4] should be 0x505, not decimal 505
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-23-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The SPI controllers in the MPS2 AN505 board are PL022s.
We have a model of the PL022, so create these devices.
We don't currently model the LCD controller that sits behind
one of the PL022s; the others are intended to control devices
that sit on the FPGA's general purpose SPI connector or
"shield" expansion connectors.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-22-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
In the PL022, register offset 0x20 is the ICR, a write-only
interrupt-clear register. Register offset 0x24 is DMACR, the DMA
control register. We were incorrectly implementing (a stub version
of) DMACR at 0x20, and not implementing anything at 0x24. Fix this
bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-21-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL022 interrupt registers have bits allocated as:
0: ROR (receive overrun)
1: RT (receive timeout)
2: RX (receive FIFO half full or less)
3: TX (transmit FIFO half full or less)
A cut and paste error meant we had the wrong value for
the PL022_INT_RT constant. This bug doesn't affect device
behaviour, because we don't implement the receive timeout
feature and so never set that interrupt bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-20-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Move from the legacy SysBusDevice::init method to using
DeviceState::realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-19-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Use the DeviceState vmsd pointer rather than calling vmstate_register()
directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-18-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the PL022 calls pl022_reset() from its class init
function. Make it register a DeviceState reset method instead,
so that we reset the device on system reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-17-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl022's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
While we're adding the new file to MAINTAINERS, add
also the .c file, which was missing an entry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-16-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Peter Maydell