arm: add dummy A9-specific cp15 registers

Add dummy register support for the cp15, CRn=c15 registers.

config_base_register and power_control_register currently
default to 0, but may have improved support after the QOM
CPU patches are finished.

Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target-arm/cpu.h

@@ -149,6 +149,10 @@ typedef struct CPUARMState {
         uint32_t c15_i_max; /* Maximum D-cache dirty line index.  */
         uint32_t c15_i_min; /* Minimum D-cache dirty line index.  */
         uint32_t c15_threadid; /* TI debugger thread-ID.  */
+        uint32_t c15_config_base_address; /* SCU base address.  */
+        uint32_t c15_diagnostic; /* diagnostic register */
+        uint32_t c15_power_diagnostic;
+        uint32_t c15_power_control; /* power control */
     } cp15;
 
     struct {
@@ -448,7 +452,7 @@ void cpu_arm_set_cp_io(CPUARMState *env, int cpnum,
 #define cpu_signal_handler cpu_arm_signal_handler
 #define cpu_list arm_cpu_list
 
-#define CPU_SAVE_VERSION 4
+#define CPU_SAVE_VERSION 5
 
 /* MMU modes definitions */
 #define MMU_MODE0_SUFFIX _kernel

target-arm/helper.c

@@ -1796,6 +1796,20 @@ void HELPER(set_cp15)(CPUState *env, uint32_t insn, uint32_t val)
                 goto bad_reg;
             }
         }
+        if (ARM_CPUID(env) == ARM_CPUID_CORTEXA9) {
+            switch (crm) {
+            case 0:
+                if ((op1 == 0) && (op2 == 0)) {
+                    env->cp15.c15_power_control = val;
+                } else if ((op1 == 0) && (op2 == 1)) {
+                    env->cp15.c15_diagnostic = val;
+                } else if ((op1 == 0) && (op2 == 2)) {
+                    env->cp15.c15_power_diagnostic = val;
+                }
+            default:
+                break;
+            }
+        }
         break;
     }
     return;
@@ -2139,6 +2153,40 @@ uint32_t HELPER(get_cp15)(CPUState *env, uint32_t insn)
              * 0x200 << ($rn & 0xfff), when MMU is off.  */
             goto bad_reg;
         }
+        if (ARM_CPUID(env) == ARM_CPUID_CORTEXA9) {
+            switch (crm) {
+            case 0:
+                if ((op1 == 4) && (op2 == 0)) {
+                    /* The config_base_address should hold the value of
+                     * the peripheral base. ARM should get this from a CPU
+                     * object property, but that support isn't available in
+                     * December 2011. Default to 0 for now and board models
+                     * that care can set it by a private hook */
+                    return env->cp15.c15_config_base_address;
+                } else if ((op1 == 0) && (op2 == 0)) {
+                    /* power_control should be set to maximum latency. Again,
+                       default to 0 and set by private hook */
+                    return env->cp15.c15_power_control;
+                } else if ((op1 == 0) && (op2 == 1)) {
+                    return env->cp15.c15_diagnostic;
+                } else if ((op1 == 0) && (op2 == 2)) {
+                    return env->cp15.c15_power_diagnostic;
+                }
+                break;
+            case 1: /* NEON Busy */
+                return 0;
+            case 5: /* tlb lockdown */
+            case 6:
+            case 7:
+                if ((op1 == 5) && (op2 == 2)) {
+                    return 0;
+                }
+                break;
+            default:
+                break;
+            }
+            goto bad_reg;
+        }
         return 0;
     }
 bad_reg:

target-arm/machine.c

@@ -56,6 +56,9 @@ void cpu_save(QEMUFile *f, void *opaque)
     qemu_put_be32(f, env->cp15.c13_tls2);
     qemu_put_be32(f, env->cp15.c13_tls3);
     qemu_put_be32(f, env->cp15.c15_cpar);
+    qemu_put_be32(f, env->cp15.c15_power_control);
+    qemu_put_be32(f, env->cp15.c15_diagnostic);
+    qemu_put_be32(f, env->cp15.c15_power_diagnostic);
 
     qemu_put_be32(f, env->features);
 
@@ -170,6 +173,9 @@ int cpu_load(QEMUFile *f, void *opaque, int version_id)
     env->cp15.c13_tls2 = qemu_get_be32(f);
     env->cp15.c13_tls3 = qemu_get_be32(f);
     env->cp15.c15_cpar = qemu_get_be32(f);
+    env->cp15.c15_power_control = qemu_get_be32(f);
+    env->cp15.c15_diagnostic = qemu_get_be32(f);
+    env->cp15.c15_power_diagnostic = qemu_get_be32(f);
 
     env->features = qemu_get_be32(f);