When viewing/debugging memory regions it is sometimes hard to figure
out which PCI device something belongs to. Make the names unique by
including the vdev name in the name string.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20210213130325.14781-2-alex.bennee@linaro.org>
Without that wireshark complains about invalid control setup data
for non-control transfers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210216144939.841873-1-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In order to keep track of the alternate setting that should be used for
a given interface, the USBDevice struct keeps an array of alternate
setting values, which is indexed by the interface number. In
usb_host_set_interface, when this array is updated, usb_host_ep_update
is called as a result. However, when usb_host_ep_update accesses the
active libusb_config_descriptor, it indexes udev->altsetting with the
loop variable, rather than the interface number.
With the simple trace backend enable, this behavior can be seen:
[...]
usb_xhci_xfer_start 0.440 pid=1215 xfer=0x5596a4b85930 slotid=0x1 epid=0x1 streamid=0x0
usb_packet_state_change 1.703 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'undef' n=b'setup'
usb_host_req_control 2.269 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 req=0x10b value=0x1 index=0xd
usb_host_set_interface 0.449 pid=1215 bus=0x1 addr=0x5 interface=0xd alt=0x1
usb_host_parse_config 2542.648 pid=1215 bus=0x1 addr=0x5 value=0x2 active=0x1
usb_host_parse_interface 1.804 pid=1215 bus=0x1 addr=0x5 num=0xc alt=0x0 active=0x1
usb_host_parse_endpoint 2.012 pid=1215 bus=0x1 addr=0x5 ep=0x2 dir=b'in' type=b'int' active=0x1
usb_host_parse_interface 1.598 pid=1215 bus=0x1 addr=0x5 num=0xd alt=0x0 active=0x1
usb_host_req_emulated 3.593 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 status=0x0
usb_packet_state_change 2.550 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'setup' n=b'complete'
usb_xhci_xfer_success 4.298 pid=1215 xfer=0x5596a4b85930 bytes=0x0
[...]
In particular, it is seen that although usb_host_set_interface sets the
alternate setting of interface 0xd to 0x1, usb_host_ep_update uses 0x0
as the alternate setting due to using the incorrect index to
udev->altsetting.
Fix this problem by getting the interface number from the active
libusb_config_descriptor, and then using that as the index to
udev->altsetting.
Signed-off-by: Nick Rosbrook <rosbrookn@ainfosec.com>
Message-Id: <20210201213021.500277-1-rosbrookn@ainfosec.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When SEV-ES is enabled, it is not possible modify the guests register
state after it has been initially created, encrypted and measured.
Normally, an INIT-SIPI-SIPI request is used to boot the AP. However, the
hypervisor cannot emulate this because it cannot update the AP register
state. For the very first boot by an AP, the reset vector CS segment
value and the EIP value must be programmed before the register has been
encrypted and measured. Search the guest firmware for the guest for a
specific GUID that tells Qemu the value of the reset vector to use.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <22db2bfb4d6551aed661a9ae95b4fdbef613ca21.1611682609.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector. The table goes
backwards in memory so all entries are of the form
<data>|len|<GUID>
Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.
The foot of the table is of this form and <len> for this case
describes the entire size of the table. The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.
Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux blkfront expects both "discard-granularity" and
"discard-alignment" present on xenbus in order to properly enable the
feature, not exposing "discard-alignment" left some Linux blkfront
versions with a broken discard setup. This has also been addressed in
Linux with:
https://lore.kernel.org/lkml/20210118151528.81668-1-roger.pau@citrix.com/T/#u
Fix QEMU to report a "discard-alignment" of 0, in order for it to work
with older Linux frontends.
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Message-Id: <20210118153330.82324-1-roger.pau@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
cmd_fis is mapped as DMA_DIRECTION_FROM_DEVICE, however, it is read
from, and not written to anywhere. Fix the DMA_DIRECTION and mark
cmd_fis as read-only in the code.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210119164051.89268-1-alxndr@bu.edu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Copy bootinfo.h and bootinfo-mac.h from arch/m68k/include/uapi/asm/
to include/standard-headers/asm-m68k/
Imported from linux v5.9 but didn't change since v4.14 (header update)
and since v4.10 (content update).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20201220112615.933036-2-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Use nr_apu_cpus in favor of hard coding 2.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210210142048.3125878-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
nvme_ns_realize passes errp to nvme_register_namespaces, but then try to
prepend errp with local_err.
Just remove the local_err and use errp directly.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Current QEMU HEAD nvme.c does not compile with the default GCC 5.4
on a Ubuntu 16.04 host:
hw/block/nvme.c:3242:9: error: ‘result’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
trace_pci_nvme_getfeat_vwcache(result ? "enabled" : "disabled");
^
hw/block/nvme.c:3150:14: note: ‘result’ was declared here
uint32_t result;
^
Explicitly initialize the result to fix it.
Fixes: aa5e55e3b0 ("hw/block/nvme: open code for volatile write cache")
Fixes: Coverity CID 1446371
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Moving namespace registration to the nvme-ns realization function had
the unintended side-effect of breaking legacy namespace registration.
Fix this.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Reported-by: Alexander Graf <agraf@csgraf.de>
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents. (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)
This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
NPCM7XX GPIO devices have been implemented in hw/gpio/npcm7xx-gpio.c. So
we removed them from the unimplemented devices list.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu<wuhaotsh@google.com>
Message-id: 20210129005845.416272-2-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Perform device reset in the remote process when QEMU performs
device reset. This is required to reset the internal state
(like registers, etc...) of emulated devices
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7cb220a51f565dc0817bd76e2f540e89c2d2b850.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Retrieve PCI configuration info about the remote device and
configure the Proxy PCI object based on the returned information
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 85ee367bbb993aa23699b44cfedd83b4ea6d5221.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IOHUB object is added to manage PCI IRQs. It uses KVM_IRQFD
ioctl to create irqfd to injecting PCI interrupts to the guest.
IOHUB object forwards the irqfd to the remote process. Remote process
uses this fd to directly send interrupts to the guest, bypassing QEMU.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 51d5c3d54e28a68b002e3875c59599c9f5a424a1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add ProxyMemoryListener object which is used to keep the view of the RAM
in sync between QEMU and remote process.
A MemoryListener is registered for system-memory AddressSpace. The
listener sends SYNC_SYSMEM message to the remote process when memory
listener commits the changes to memory, the remote process receives
the message and processes it in the handler for SYNC_SYSMEM message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 04fe4e6a9ca90d4f11ab6f59be7652f5b086a071.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Proxy device object implements handler for PCI BAR writes and reads.
The handler uses BAR_WRITE/BAR_READ message to communicate to the
remote process with the BAR address and value to be written/read.
The remote process implements handler for BAR_WRITE/BAR_READ
message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: a8b76714a9688be5552c4c92d089bc9e8a4707ff.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The Proxy Object sends the PCI config space accesses as messages
to the remote process over the communication channel
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d3c94f4618813234655356c60e6f0d0362ff42d6.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d54edb4176361eed86b903e8f27058363b6c83b3.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Defines a PCI Device proxy object as a child of TYPE_PCI_DEVICE.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: b5186ebfedf8e557044d09a768846c59230ad3a7.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
SyncSysMemMsg message format is defined. It is used to send
file descriptors of the RAM regions to remote device.
RAM on the remote device is configured with a set of file descriptors.
Old RAM regions are deleted and new regions, each with an fd, is
added to the RAM.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7d2d1831d812e85f681e7a8ab99e032cf4704689.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Associate the file descriptor for a PCIDevice in remote process with
DeviceState object.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: f405a2ed5d7518b87bea7c59cfdf334d67e5ee51.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Initializes the message handler function in the remote process. It is
called whenever there's an event pending on QIOChannel that registers
this function.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 99d38d8b93753a6409ac2340e858858cda59ab1b.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Defines MPQemuMsg, which is the message that is sent to the remote
process. This message is sent over QIOChannel and is used to
command the remote process to perform various tasks.
Define transmission functions used by proxy and by remote.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 56ca8bcf95195b2b195b08f6b9565b6d7410bce5.1611938319.git.jag.raman@oracle.com
[Replace struct iovec send[2] = {0} with {} to make clang happy as
suggested by Peter Maydell <peter.maydell@linaro.org>.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
x-remote-machine object sets up various subsystems of the remote
device process. Instantiate PCI host bridge object and initialize RAM, IO &
PCI memory regions.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: c537f38d17f90453ca610c6b70cf3480274e0ba1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
PCI host bridge is setup for the remote device process. It is
implemented using remote-pcihost object. It is an extension of the PCI
host bridge setup by QEMU.
Remote-pcihost configures a PCI bus which could be used by the remote
PCI device to latch on to.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 0871ba857abb2eafacde07e7fe66a3f12415bfb2.1611938319.git.jag.raman@oracle.com
[Added PCI_EXPRESS condition in hw/remote/Kconfig since remote-pcihost
needs PCIe. This solves "make check" failure on s390x. Fix suggested by
Philippe Mathieu-Daudé <philmd@redhat.com> and Thomas Huth
<thuth@redhat.com>.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Per MPC8548ERM [1] chapter 14.5.3.4.1:
When RCTRL.RSF is 1, frames less than 64 bytes are accepted upon
a DA match. But currently QEMU does the opposite. This commit
reverses the RCTRL.RSF testing logic to match the manual.
Due to the reverse of the logic, certain guests may potentially
break if they don't program eTSEC to have RCTRL.RSF bit set.
When RCTRL.RSF is 0, short frames are silently dropped, however
as of today both slirp and tap networking do not pad short frames
(e.g.: an ARP packet) to the minimum frame size of 60 bytes. So
ARP requests will be dropped, preventing the guest from becoming
visible on the network.
The same issue was reported on e1000 and vmxenet3 before, see:
commit 78aeb23ede ("e1000: Pad short frames to minimum size (60 bytes)")
commit 40a87c6c9b ("vmxnet3: Pad short frames to minimum size (60 bytes)")
[1] https://www.nxp.com/docs/en/reference-manual/MPC8548ERM.pdf
Fixes: eb1e7c3e51 ("Add Enhanced Three-Speed Ethernet Controller (eTSEC)")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <1612923021-19746-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present the <clock-frequency> property of the serial node is
populated with value zero. U-Boot's ns16550 driver is not happy
about this, so let's fill in a meaningful value.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1612362288-22216-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present the platform clock frequency is using a magic number.
Convert it to a macro and use it everywhere.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1612362288-22216-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current logic for calculating 'maxdomain' making it a sum of
numa_state->num_nodes with spapr->gpu_numa_id. spapr->gpu_numa_id is
used as a index to determine the next available NUMA id that a
given NVGPU can use.
The problem is that the initial value of gpu_numa_id, for any topology
that has more than one NUMA node, is equal to numa_state->num_nodes.
This means that our maxdomain will always be, at least, twice the
amount of existing NUMA nodes. This means that a guest with 4 NUMA
nodes will end up with the following max-associativity-domains:
rtas/ibm,max-associativity-domains
00000004 00000008 00000008 00000008 00000008
This overtuning of maxdomains doesn't go unnoticed in the guest, being
detected in SLUB during boot:
dmesg | grep SLUB
[ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=8
SLUB is detecting 8 total nodes, with 4 nodes being online.
This patch fixes ibm,max-associativity-domains by considering the amount
of NVGPUs NUMA nodes presented in the guest, instead of just
spapr->gpu_numa_id.
Reported-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-4-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We'll need to check the initial value given to spapr->gpu_numa_id when
building the rtas DT, so put it in a helper for easier access and to
avoid repetition.
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is used only in spapr_numa.c.
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This to map the PNOR from the machine init handler directly and finish
the cleanup of the LPC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-8-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On PowerNV systems, the BMC is in charge of mapping the PNOR contents
on the LPC FW address space using the HIOMAP protocol. Under QEMU, we
emulate this behavior and we also add an extra control on the flash
accesses by letting the HIOMAP command handler decide whether the
memory region is accessible or not depending on the firmware requests.
However, this behavior is not compatible with hostboot like firmwares
which need this mapping to be always available. For this reason, the
PNOR memory region is initially disabled for skiboot mode only.
This is badly placed under the LPC model and requires the use of the
machine. Since it doesn't add much, simply remove the initial setting.
The extra control in the HIOMAP command handler will still be performed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-7-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine can be run with an external IPMI BMC device
connected to a remote QEMU machine acting as BMC, using these options :
-chardev socket,id=ipmi0,host=localhost,port=9002,reconnect=10 \
-device ipmi-bmc-extern,id=bmc0,chardev=ipmi0 \
-device isa-ipmi-bt,bmc=bmc0,irq=10 \
-nodefaults
In that case, some aspects of the BMC initialization should be
skipped, since they rely on the simulator interface.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-6-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
and reuse pnv_bmc_set_pnor() to share the setting of the PNOR.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current settings are useful to load large kernels (with debug) but
it moves the initrd image in a memory region not protected by
skiboot. If skiboot is compiled with DEBUG=1, memory poisoning will
corrupt the initrd.
Cc: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-4-clg@kaod.org>
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ENDs allocated by OPAL for the HW thread VPs are tagged as owned by FW.
Dump the state in 'info pic'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER9 systems, PHB controllers signal the XIVE interrupt controller
of a source interrupt notification using a store on a MMIO region. Add
traces for such events.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is currently not possible to perform a strict boot from USB storage:
$ qemu-system-ppc64 -accel kvm -nodefaults -nographic -serial stdio \
-boot strict=on \
-device qemu-xhci \
-device usb-storage,drive=disk,bootindex=0 \
-blockdev driver=file,node-name=disk,filename=fedora-ppc64le.qcow2
SLOF **********************************************************************
QEMU Starting
Build Date = Jul 17 2020 11:15:24
FW Version = git-e18ddad8516ff2cf
Press "s" to enter Open Firmware.
Populating /vdevice methods
Populating /vdevice/vty@71000000
Populating /vdevice/nvram@71000001
Populating /pci@800000020000000
00 0000 (D) : 1b36 000d serial bus [ usb-xhci ]
No NVRAM common partition, re-initializing...
Scanning USB
XHCI: Initializing
USB Storage
SCSI: Looking for devices
101000000000000 DISK : "QEMU QEMU HARDDISK 2.5+"
Using default console: /vdevice/vty@71000000
Welcome to Open Firmware
Copyright (c) 2004, 2017 IBM Corporation All rights reserved.
This program and the accompanying materials are made available
under the terms of the BSD License available at
http://www.opensource.org/licenses/bsd-license.php
Trying to load: from: /pci@800000020000000/usb@0/storage@1/disk@101000000000000 ...
E3405: No such device
E3407: Load failed
Type 'boot' and press return to continue booting the system.
Type 'reset-all' and press return to reboot the system.
Ready!
0 >
The device tree handed over by QEMU to SLOF indeed contains:
qemu,boot-list =
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000 HALT";
but the device node is named usb-xhci@0, not usb@0.
This happens because the firmware names of PCI devices returned
by get_boot_devices_list() come from pcibus_get_fw_dev_path(),
while the sPAPR PHB code uses a different naming scheme for
device nodes. This inconsistency has always been there but it was
hidden for a long time because SLOF used to rename USB device
nodes, until this commit, merged in QEMU 4.2.0 :
commit 85164ad4ed
Author: Alexey Kardashevskiy <aik@ozlabs.ru>
Date: Wed Sep 11 16:24:32 2019 +1000
pseries: Update SLOF firmware image
This fixes USB host bus adapter name in the device tree to match QEMU's
one.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fortunately, sPAPR implements the firmware path provider interface.
This provides a way to override the default firmware paths.
Just factor out the sPAPR PHB naming logic from spapr_dt_pci_device()
to a helper, and use it in the sPAPR firmware path provider hook.
Fixes: 85164ad4ed ("pseries: Update SLOF firmware image")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210122170157.246374-1-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In the CPU hotunplug bug [1] the guest kernel throws a scary
message in dmesg:
pseries-hotplug-cpu: Failed to offline CPU <NULL>, rc: -16
The reason isn't related to the bug though. This happens because the
kernel file arch/powerpc/platform/pseries/hotplug-cpu.c, function
dlpar_cpu_remove(), is not finding the device_node.name of the offending
CPU.
We're not populating the 'name' property for hotplugged CPUs. Since the
kernel relies on device_node.name for identifying CPU nodes, and the
CPUs that are coldplugged has the 'name' property filled by SLOF, this
is creating an unneeded inconsistency between hotplug and coldplug CPUs
in the kernel.
Let's fill the 'name' property for hotplugged CPUs as well. This will
make the guest dmesg throws a less intimidating message when we try to
unplug the last online CPU:
pseries-hotplug-cpu: Failed to offline CPU PowerPC,POWER9@1, rc: -16
[1] https://bugzilla.redhat.com/1911414
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210120232305.241521-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Next patch will use the 'nodename' string in spapr_core_dt_populate()
after the point it's being freed today.
Instead of moving 'g_free(nodename)' around, let's do a QoL change in
both CPU DT functions where 'nodename' is being freed, and use
g_autofree to avoid the 'g_free()' call altogether.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210120232305.241521-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add configuration options to enable or disable multiprocess QEMU code
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 6cc37253e35418ebd7b675a31a3df6e3c7a12dc1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Allow RAM MemoryRegion to be created from an offset in a file, instead
of allocating at offset of 0 by default. This is needed to synchronize
RAM between QEMU & remote process.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 609996697ad8617e3b01df38accc5c208c24d74e.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Refactor the zone write check logic such that the most "meaningful"
error is returned first. That is, first, if the zone is not writable,
return an appropriate status code for that. Then, make sure we are
actually writing at the write pointer and finally check that we do not
cross the zone write boundary. This aligns with the "priority" of status
codes for zone read checks.
Also add a couple of additional descriptive trace events and remove an
always true assert.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
When a zone append is processed the controller checks that validity of
the write before assigning the LBA to the append command. This causes
the boundary check to be wrong.
Fix this by checking the write *after* assigning the LBA. Remove the
append special case from the nvme_check_zone_write and open code it in
nvme_do_write, assigning the slba when basic sanity checks have been
performed. Then check the validity of the resulting write like any other
write command.
In the process, also fix a missing endianness conversion for the zone
append ALBA.
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The actual parameter name is 'cross_read' rather than 'cross_zone_read'.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Change status checks to align with the existing style and remove the
explicit check against NVME_SUCCESS.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Currently, no features are saveable, so the current check is not wrong,
but add a check against the feature capabilities to make sure this will
not regress if saveable features are added later.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Only enable DULBE if the namespace supports it.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If a user assigns a backing device with less capacity than the size of a
single zone, the namespace capacity will be reported as zero and the
kernel will silently fail to allocate the namespace.
This patch errors out in case that the backing device cannot accomodate
at least a single zone.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[k.jensen: small fixup in the error and commit message]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The controller now implements v1.4 and we can lift the restrictions on
CMB Data Pointer and Command Independent Locations Support (CDPCILS) and
CMB Data Pointer Mixed Locations Support (CDPMLS) since the device
really does not care about mixed host/cmb pointers in those cases.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
With the new CMB logic in place, bump the implemented specification
version to v1.4 by default.
This requires adding the setting the CNTRLTYPE field and modifying the
VWC field since 0x00 is no longer a valid value for bits 2:1.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Implement v1.4 logic for configuring the Controller Memory Buffer. By
default, the v1.4 scheme will be used (CMB must be explicitly enabled by
the host), so drivers that only support v1.3 will not be able to use the
CMB anymore.
To retain the v1.3 behavior, set the boolean 'legacy-cmb' nvme device
parameter.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Padmakar Kalghatgi <p.kalghatgi@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for the PMRMSCL and PMRMSCU MMIO registers. This allows
adding RDS/WDS support for PMR as well.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Naveen Nagar <naveen.n1@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The PMR should not be enabled at boot up. Disable the PMR MemoryRegion
initially and implement MMIO for PMRCTL, allowing the host to enable the
PMR explicitly.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The controller registers are initially zero. Remove the redundant
zeroing.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Use the correct field names.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
With BAR 4 now free to use, allow PMR and CMB to be enabled
simultaneously.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In the interest of supporting both CMB and PMR to be enabled on the same
device, move the MSI-X table and pending bit array out of BAR 4 and into
BAR 0.
This is a simplified version of the patch contributed by Andrzej
Jakowski (see [1]). Leaving the CMB at offset 0 removes the need for
changes to CMB address mapping code.
[1]: https://lore.kernel.org/qemu-devel/20200729220107.37758-3-andrzej.jakowski@linux.intel.com/
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch sets CMBS bit in controller capabilities register when user
configures NVMe driver with CMB support, so capabilites are correctly
reported to guest OS.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Reviewed-by: Maxim Levitsky <mlevitsky@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
64 bit registers like ASQ and ACQ should be writable by both a hi/lo 32
bit write combination as well as a plain 64 bit write. The spec does not
define ordering on the hi/lo split, but the code currently assumes that
the low order bits are written first. Additionally, the code does not
consider that another address might already have been written into the
register, causing the OR'ing to result in a bad address.
Fix this by explicitly overwriting only the low or high order bits for
32 bit writes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add the size of the mmio read/write to the trace event.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
During smart critical warning injection by setting property from QMP
command, also try to trigger asynchronous event.
Suggested by Keith, if a event has already been raised, there is no
need to enqueue the duplicate event any more.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
[k.jensen: fix typo in commit message]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
There is a very low probability that hitting physical NVMe disk
hardware critical warning case, it's hard to write & test a monitor
agent service.
For debugging purposes, add a new 'smart_critical_warning' property
to emulate this situation.
The orignal version of this change is implemented by adding a fixed
property which could be initialized by QEMU command line. Suggested
by Philippe & Klaus, rework like current version.
Test with this patch:
1, change smart_critical_warning property for a running VM:
#virsh qemu-monitor-command nvme-upstream '{ "execute": "qom-set",
"arguments": { "path": "/machine/peripheral-anon/device[0]",
"property": "smart_critical_warning", "value":16 } }'
2, run smartctl in guest
#smartctl -H -l error /dev/nvme0n1
=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
- volatile memory backup device has failed
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The zone write pointer is unconditionally advanced, even for write
faults. Make sure that the zone is always transitioned to Full if the
write pointer reaches zone capacity.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_ns_setup() finally does not have nothing to do with NvmeCtrl
instance.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In NVMe, namespace is being attached to process I/O. We register NVMe
namespace to a controller via nvme_register_namespace() during
nvme_ns_setup(). This is main reason of receiving NvmeCtrl object
instance to this function to map the namespace to a controller.
To make namespace instance more independent, it should be split into two
parts: setup and register. This patch split them into two differnt
parts, and finally nvme_ns_setup() does not have nothing to do with
NvmeCtrl instance at all.
This patch is a former patch to introduce NVMe subsystem scheme to the
existing design especially for multi-path. In that case, it should be
split into two to make namespace independent from a controller.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Removed no longer used aregument NvmeCtrl object in nvme_ns_init_blk().
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Volatile Write Cache(VWC) feature is set in nvme_ns_setup() in the
initial time. This feature is related to block device backed, but this
feature is controlled in controller level via Set/Get Features command.
This patch removed dependency between nvme and nvme-ns to manage the VWC
flag value. Also, it open coded the Get Features for VWC to check all
namespaces attached to the controller, and if false detected, return
directly false.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[k.jensen: report write cache preset if present on ANY namespace]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_ns_init_zoned() has no use for given NvmeCtrl object.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
TP 4053 says (in section 2.3.1.1) -
... if a Zone Append command specifies a ZSLBA that is not the lowest
logical block address in that zone, then the controller shall abort
that command with a status code of Invalid Field In Command.
In the code, Zone Invalid Write is returned instead, fix this.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_io_cmd already checks if the namespace supports the Zone Append
command, so the removed check is dead code.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Add missing string representations for a couple of new commands.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
The zoned command set specification states that "All logical blocks in a
zone *shall* be marked as deallocated when [the zone is reset]". Since
the device guarantees 0x00 to be read from deallocated blocks we have to
issue a pwrite_zeroes since we cannot be sure that a discard will do
anything. But typically, this will be achieved with an efficient
unmap/discard operation.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Align with existing style and use a typedef for header-file enums.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Implicitly and explicitly opended zones are always bulk processed
together, so merge the two processing masks.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
A shutdown is only about flushing stuff. It is the host that should
delete any queues, so do not perform a reset here.
Also, on shutdown, make sure that the PMR is flushed if in use.
Fixes: 368f4e752cf9 ("hw/block/nvme: Process controller reset and shutdown differently")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
The device uses the BDRV_BLOCK_ZERO flag to determine the "deallocated"
status of logical blocks. Since the zoned namespaces command set
specification defines that logical blocks SHALL be marked as deallocated
when the zone is in the Empty or Offline states, DULBE can only be
supported if the zone size is a multiple of the calculated deallocation
granularity (reported in NPDG) which depends on the underlying block
device cluster size (if applicable) or the configured
discard_granularity.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 1c0c2163aa ("hw/block/nvme: verify msix_init_exclusive_bar()
return value") had the unintended effect of breaking support on
several platforms not supporting MSI-X.
Still check for errors, but only report that MSI-X is unsupported
instead of bailing out.
Fixes: 1c0c2163aa ("hw/block/nvme: verify msix_init_exclusive_bar() return value")
Fixes: fbf2e5375e ("hw/block/nvme: Verify msix_vector_use() returned value")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Added brief descriptions of the new device properties that are
now available to users to configure features of Zoned Namespace
Command Set in the emulator.
This patch is for documentation only, no functionality change.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Zone Descriptor Extension is a label that can be assigned to a zone.
It can be set to an Empty zone and it stays assigned until the zone
is reset.
This commit adds a new optional module property,
"zoned.descr_ext_size". Its value must be a multiple of 64 bytes.
If this value is non-zero, it becomes possible to assign extensions
of that size to any Empty zones. The default value for this property
is 0, therefore setting extensions is disabled by default.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add two module properties, "zoned.max_active" and "zoned.max_open"
to control the maximum number of zones that can be active or open.
Once these variables are set to non-default values, these limits are
checked during I/O and Too Many Active or Too Many Open command status
is returned if they are exceeded.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The emulation code has been changed to advertise NVM Command Set when
"zoned" device property is not set (default) and Zoned Namespace
Command Set otherwise.
Define values and structures that are needed to support Zoned
Namespace Command Set (NVMe TP 4053) in PCI NVMe controller emulator.
Define trace events where needed in newly introduced code.
In order to improve scalability, all open, closed and full zones
are organized in separate linked lists. Consequently, almost all
zone operations don't require scanning of the entire zone array
(which potentially can be quite large) - it is only necessary to
enumerate one or more zone lists.
Handlers for three new NVMe commands introduced in Zoned Namespace
Command Set specification are added, namely for Zone Management
Receive, Zone Management Send and Zone Append.
Device initialization code has been extended to create a proper
configuration for zoned operation using device properties.
Read/Write command handler is modified to only allow writes at the
write pointer if the namespace is zoned. For Zone Append command,
writes implicitly happen at the write pointer and the starting write
pointer value is returned as the result of the command. Write Zeroes
handler is modified to add zoned checks that are identical to those
done as a part of Write flow.
Subsequent commits in this series add ZDE support and checks for
active and open zone limits.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Matias Bjorling <matias.bjorling@wdc.com>
Signed-off-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Many CNS commands have "allocated" command variants. These include
a namespace as long as it is allocated, that is a namespace is
included regardless if it is active (attached) or not.
While these commands are optional (they are mandatory for controllers
supporting the namespace attachment command), our QEMU implementation
is more complete by actually providing support for these CNS values.
However, since our QEMU model currently does not support the namespace
attachment command, these new allocated CNS commands will return the
same result as the active CNS command variants.
The reason for not hooking up this command completely is because the
NVMe specification requires the namespace management command to be
supported if the namespace attachment command is supported.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Define the structures and constants required to implement
Namespace Types support.
Namespace Types introduce a new command set, "I/O Command Sets",
that allows the host to retrieve the command sets associated with
a namespace. Introduce support for the command set and enable
detection for the NVM Command Set.
The new workflows for identify commands rely heavily on zero-filled
identify structs. E.g., certain CNS commands are defined to return
a zero-filled identify struct when an inactive namespace NSID
is supplied.
Add a helper function in order to avoid code duplication when
reporting zero-filled identify structures.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This log page becomes necessary to implement to allow checking for
Zone Append command support in Zoned Namespace Command Set.
This commit adds the code to report this log page for NVM Command
Set only. The parts that are specific to zoned operation will be
added later in the series.
All incoming admin and i/o commands are now only processed if their
corresponding support bits are set in this log. This provides an
easy way to control what commands to support and what not to
depending on set CC.CSS.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
v2
Dropped vmstate: Fix memory leak in vmstate_handle_alloc
Broke on Power
Added migration: only check page size match if RAM postcopy is enabled
-----BEGIN PGP SIGNATURE-----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=4tbe
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20210208a' into staging
Migration pull 2021-02-08
v2
Dropped vmstate: Fix memory leak in vmstate_handle_alloc
Broke on Power
Added migration: only check page size match if RAM postcopy is enabled
# gpg: Signature made Mon 08 Feb 2021 11:28:14 GMT
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20210208a: (27 commits)
migration: only check page size match if RAM postcopy is enabled
migration: introduce snapshot-{save, load, delete} QMP commands
iotests: fix loading of common.config from tests/ subdir
iotests: add support for capturing and matching QMP events
migration: introduce a delete_snapshot wrapper
migration: wire up support for snapshot device selection
migration: control whether snapshots are ovewritten
block: rename and alter bdrv_all_find_snapshot semantics
block: allow specifying name of block device for vmstate storage
block: add ability to specify list of blockdevs during snapshot
migration: stop returning errno from load_snapshot()
migration: Make save_snapshot() return bool, not 0/-1
block: push error reporting into bdrv_all_*_snapshot functions
migration: Display the migration blockers
migration: Add blocker information
migration: Fix a few absurdly defective error messages
migration: Fix cache_init()'s "Failed to allocate" error messages
migration: Clean up signed vs. unsigned XBZRLE cache-size
migration: Fix migrate-set-parameters argument validation
migration: introduce 'userfaultfd-wrlat.py' script
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move write processing to nvme_do_write() that now handles both WRITE
and WRITE ZEROES. Both nvme_write() and nvme_write_zeroes() become
inline helper functions.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The majority of code in nvme_rw() is becoming read- or write-specific.
Move these parts to two separate handlers, nvme_read() and nvme_write()
to make the code more readable and to remove multiple is_write checks
that has been present in the i/o path.
This is a refactoring patch, no change in functionality.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In NVMe 1.4, a namespace must report an ID descriptor of UUID type
if it doesn't support EUI64 or NGUID. Add a new namespace property,
"uuid", that provides the user the option to either specify the UUID
explicitly or have a UUID generated automatically every time a
namespace is initialized.
Suggested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Controller reset ans subsystem shutdown are handled very much the same
in the current code, but some of the steps should be different in these
two cases.
Introduce two new functions, nvme_reset_ctrl() and nvme_shutdown_ctrl(),
to separate some portions of the code from nvme_clear_ctrl(). The steps
that are made different between reset and shutdown are that BAR.CC is not
reset to zero upon the shutdown and namespace data is flushed to
backing storage as a part of shutdown handling, but not upon reset.
Suggested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 37712e00b1 ("hw/block/nvme: factor out pmr setup") changed the
control flow such that the CAP register is erronously cleared after
nvme_init_pmr() has configured it. Since the entire NvmeCtrl structure
is zero-filled initially, there is no need for the explicit clearing, so
just remove it.
Fixes: 37712e00b1 ("hw/block/nvme: factor out pmr setup")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add the Compare command.
This implementation uses a bounce buffer to read in the data from
storage and then compare with the host supplied buffer.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for the Dataset Management command and the Deallocate
attribute. Deallocation results in discards being sent to the underlying
block device. Whether of not the blocks are actually deallocated is
affected by the same factors as Write Zeroes (see previous commit).
format | discard | dsm (512B) dsm (4KiB) dsm (64KiB)
--------------------------------------------------------
qcow2 ignore n n n
qcow2 unmap n n y
raw ignore n n n
raw unmap n y y
Again, a raw format and 4KiB LBAs are preferable.
In order to set the Namespace Preferred Deallocate Granularity and
Alignment fields (NPDG and NPDA), choose a sane minimum discard
granularity of 4KiB. If we are using a passthru device supporting
discard at a 512B granularity, user should set the discard_granularity
property explicitly. NPDG and NPDA will also account for the
cluster_size of the block driver if required (i.e. for QCOW2).
See NVM Express 1.3d, Section 6.7 ("Dataset Management command").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for reporting the Deallocated or Unwritten Logical Block
Error (DULBE).
Rely on the block status flags reported by the block layer and consider
any block with the BDRV_BLOCK_ZERO flag to be deallocated.
Multiple factors affect when a Write Zeroes command result in
deallocation of blocks.
* the underlying file system block size
* the blockdev format
* the 'discard' and 'logical_block_size' parameters
format | discard | wz (512B) wz (4KiB) wz (64KiB)
-----------------------------------------------------
qcow2 ignore n n y
qcow2 unmap n n y
raw ignore n y y
raw unmap n y y
So, this works best with an image in raw format and 4KiB LBAs, since
holes can then be punched on a per-block basis (this assumes a file
system with a 4kb block size, YMMV). A qcow2 image, uses a cluster size
of 64KiB by default and blocks will only be marked deallocated if a full
cluster is zeroed or discarded. However, this *is* consistent with the
spec since Write Zeroes "should" deallocate the block if the Deallocate
attribute is set and "may" deallocate if the Deallocate attribute is not
set. Thus, we always try to deallocate (the BDRV_REQ_MAY_UNMAP flag is
always set).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add a new function, nvme_aio_err, to handle errors resulting from AIOs
and use this from the callbacks.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_check_bounds has no use of the NvmeCtrl parameter; remove it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Count number of queues that we initialized and only deinitialize these that we
initialized successfully.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201217150040.906961-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When VM migrate VMState of spapr_pci, the field(msi_devs) of spapr_pci
having a flag of VMS_ALLOC need to allocate memory. If the src doesn't free
memory of msi_devs in SaveStateEntry of spapr_pci after QEMUFile save
VMState of spapr_pci, it may result in memory leak of msi_devs. We add the
post_save func to free memory, which prevents memory leak.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Jinhao Gao <gaojinhao@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201231061020.828-2-gaojinhao@huawei.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
At least some s390 cpu models support "Protected Virtualization" (PV),
a mechanism to protect guests from eavesdropping by a compromised
hypervisor.
This is similar in function to other mechanisms like AMD's SEV and
POWER's PEF, which are controlled by the "confidential-guest-support"
machine option. s390 is a slightly special case, because we already
supported PV, simply by using a CPU model with the required feature
(S390_FEAT_UNPACK).
To integrate this with the option used by other platforms, we
implement the following compromise:
- When the confidential-guest-support option is set, s390 will
recognize it, verify that the CPU can support PV (failing if not)
and set virtio default options necessary for encrypted or protected
guests, as on other platforms. i.e. if confidential-guest-support
is set, we will either create a guest capable of entering PV mode,
or fail outright.
- If confidential-guest-support is not set, guests might still be
able to enter PV mode, if the CPU has the right model. This may be
a little surprising, but shouldn't actually be harmful.
To start a guest supporting Protected Virtualization using the new
option use the command line arguments:
-object s390-pv-guest,id=pv0 -machine confidential-guest-support=pv0
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
The default behaviour for virtio devices is not to use the platforms normal
DMA paths, but instead to use the fact that it's running in a hypervisor
to directly access guest memory. That doesn't work if the guest's memory
is protected from hypervisor access, such as with AMD's SEV or POWER's PEF.
So, if a confidential guest mechanism is enabled, then apply the
iommu_platform=on option so it will go through normal DMA mechanisms.
Those will presumably have some way of marking memory as shared with
the hypervisor or hardware so that DMA will work.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
We haven't yet implemented the fairly involved handshaking that will be
needed to migrate PEF protected guests. For now, just use a migration
blocker so we get a meaningful error if someone attempts this (this is the
same approach used by AMD SEV).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Some upcoming POWER machines have a system called PEF (Protected
Execution Facility) which uses a small ultravisor to allow guests to
run in a way that they can't be eavesdropped by the hypervisor. The
effect is roughly similar to AMD SEV, although the mechanisms are
quite different.
Most of the work of this is done between the guest, KVM and the
ultravisor, with little need for involvement by qemu. However qemu
does need to tell KVM to allow secure VMs.
Because the availability of secure mode is a guest visible difference
which depends on having the right hardware and firmware, we don't
enable this by default. In order to run a secure guest you need to
create a "pef-guest" object and set the confidential-guest-support
property to point to it.
Note that this just *allows* secure guests, the architecture of PEF is
such that the guest still needs to talk to the ultravisor to enter
secure mode. Qemu has no direct way of knowing if the guest is in
secure mode, and certainly can't know until well after machine
creation time.
To start a PEF-capable guest, use the command line options:
-object pef-guest,id=pef0 -machine confidential-guest-support=pef0
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently the "memory-encryption" property is only looked at once we
get to kvm_init(). Although protection of guest memory from the
hypervisor isn't something that could really ever work with TCG, it's
not conceptually tied to the KVM accelerator.
In addition, the way the string property is resolved to an object is
almost identical to how a QOM link property is handled.
So, create a new "confidential-guest-support" link property which sets
this QOM interface link directly in the machine. For compatibility we
keep the "memory-encryption" property, but now implemented in terms of
the new property.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
When the "memory-encryption" property is set, we also disable KSM
merging for the guest, since it won't accomplish anything.
We want that, but doing it in the property set function itself is
thereoretically incorrect, in the unlikely event of some configuration
environment that set the property then cleared it again before
constructing the guest.
More importantly, it makes some other cleanups we want more difficult.
So, instead move this logic to machine_run_board_init() conditional on
the final value of the property.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
When AMD's SEV memory encryption is in use, flash memory banks (which are
initialed by pc_system_flash_map()) need to be encrypted with the guest's
key, so that the guest can read them.
That's abstracted via the kvm_memcrypt_encrypt_data() callback in the KVM
state.. except, that it doesn't really abstract much at all.
For starters, the only call site is in code specific to the 'pc'
family of machine types, so it's obviously specific to those and to
x86 to begin with. But it makes a bunch of further assumptions that
need not be true about an arbitrary confidential guest system based on
memory encryption, let alone one based on other mechanisms:
* it assumes that the flash memory is defined to be encrypted with the
guest key, rather than being shared with hypervisor
* it assumes that that hypervisor has some mechanism to encrypt data into
the guest, even though it can't decrypt it out, since that's the whole
point
* the interface assumes that this encrypt can be done in place, which
implies that the hypervisor can write into a confidential guests's
memory, even if what it writes isn't meaningful
So really, this "abstraction" is actually pretty specific to the way SEV
works. So, this patch removes it and instead has the PC flash
initialization code call into a SEV specific callback.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
we cannot in principle make the TCG Operations field definitions
conditional on CONFIG_TCG in code that is included by both common_ss
and specific_ss modules.
Therefore, what we can do safely to restrict the TCG fields to TCG-only
builds, is to move all tcg cpu operations into a separate header file,
which is only included by TCG, target-specific code.
This leaves just a NULL pointer in the cpu.h for the non-TCG builds.
This also tidies up the code in all targets a bit, having all TCG cpu
operations neatly contained by a dedicated data struct.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210204163931.7358-16-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
commit 568496c0c0 ("cpu: Add callback to check architectural") and
commit 3826121d92 ("target-arm: Implement checking of fired")
introduced an ARM-specific hack for cpu_check_watchpoint.
Make debug_check_watchpoint optional, and move it to tcg_ops.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210204163931.7358-15-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
commit 4061200059 ("arm: Correctly handle watchpoints for BE32 CPUs")
introduced this ARM-specific, TCG-specific hack to adjust the address,
before checking it with cpu_check_watchpoint.
Make adjust_watchpoint_address optional and move it to tcg_ops.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210204163931.7358-14-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[claudio: wrap target code around CONFIG_TCG and !CONFIG_USER_ONLY]
avoiding its use in headers used by common_ss code (should be poisoned).
Note: need to be careful with the use of CONFIG_USER_ONLY,
Message-Id: <20210204163931.7358-11-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
move away TCG-only code, make it compile only on TCG.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[claudio: moved the prototypes from hw/core/cpu.h to exec/cpu-all.h]
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210204163931.7358-4-cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
gcc is not smart enough to figure out length was validated before use as
strncpy limit, resulting in this warning:
inlined from ‘virt_set_oem_table_id’ at ../../hw/arm/virt.c:2197:5:
/usr/include/aarch64-linux-gnu/bits/string_fortified.h:106:10: error:
‘__builtin_strncpy’ specified bound depends on the length of the
source argument [-Werror=stringop-overflow=]
Simplify things by using a constant limit instead.
Fixes: 97fc5d507fca ("acpi: Permit OEM ID and OEM table ID fields to be changed")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Qemu's ACPI table generation sets the fields OEM ID and OEM table ID
to "BOCHS " and "BXPCxxxx" where "xxxx" is replaced by the ACPI
table name.
Some games like Red Dead Redemption 2 seem to check the ACPI OEM ID
and OEM table ID for the strings "BOCHS" and "BXPC" and if they are
found, the game crashes(this may be an intentional detection
mechanism to prevent playing the game in a virtualized environment).
This patch allows you to override these default values.
The feature can be used in this manner:
qemu -machine oem-id=ABCDEF,oem-table-id=GHIJKLMN
The oem-id string can be up to 6 bytes in size, and the
oem-table-id string can be up to 8 bytes in size. If the string are
smaller than their respective sizes they will be padded with space.
If either of these parameters is not set, the current default values
will be used for the one missing.
Note that the the OEM Table ID field will not be extended with the
name of the table, but will use either the default name or the user
provided one.
This does not affect the -acpitable option (for user-defined ACPI
tables), which has precedence over -machine option.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210119003216.17637-3-posteuca@mutex.one>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Not checking this can lead to invalid dev->vdev member access in
vhost_device_iotlb_miss if backend issue an iotlb message in a bad
timing, either maliciously or by a bug.
Reproduced rebooting a guest with testpmd in txonly forward mode.
#0 0x0000559ffff94394 in vhost_device_iotlb_miss (
dev=dev@entry=0x55a0012f6680, iova=10245279744, write=1)
at ../hw/virtio/vhost.c:1013
#1 0x0000559ffff9ac31 in vhost_backend_handle_iotlb_msg (
imsg=0x7ffddcfd32c0, dev=0x55a0012f6680)
at ../hw/virtio/vhost-backend.c:411
#2 vhost_backend_handle_iotlb_msg (dev=dev@entry=0x55a0012f6680,
imsg=imsg@entry=0x7ffddcfd32c0)
at ../hw/virtio/vhost-backend.c:404
#3 0x0000559fffeded7b in slave_read (opaque=0x55a0012f6680)
at ../hw/virtio/vhost-user.c:1464
#4 0x000055a0000c541b in aio_dispatch_handler (
ctx=ctx@entry=0x55a0010a2120, node=0x55a0012d9e00)
at ../util/aio-posix.c:329
Fixes: 020e571b8b ("vhost: rework IOTLB messaging")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20210129090728.831208-1-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This property was only required for compatibility reasons in the
pc-1.0 machine type and earlier. Now that these machine types have
been removed, the property is not useful anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210203171832.483176-4-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
They have been deprecated since QEMU v5.0, time to remove them now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210203171832.483176-2-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Previous work on dev-iotlb message broke vhost on either SMMU or virtio-iommu
since dev-iotlb (or PCIe ATS) is not yet supported for those archs.
An initial idea is that we can let IOMMU to export this information to vhost so
that vhost would know whether the vIOMMU would support dev-iotlb, then vhost
can conditionally register to dev-iotlb or the old iotlb way. We can work
based on some previous patch to introduce PCIIOMMUOps as Yi Liu proposed [1].
However it's not as easy as I thought since vhost_iommu_region_add() does not
have a PCIDevice context at all since it's completely a backend. It seems
non-trivial to pass over a PCI device to the backend during init. E.g. when
the IOMMU notifier registered hdev->vdev is still NULL.
To make the fix smaller and easier, this patch goes the other way to leverage
the flag_changed() hook of vIOMMUs so that SMMU and virtio-iommu can trap the
dev-iotlb registration and fail it. Then vhost could try the fallback solution
as using UNMAP invalidation for it's translations.
[1] https://lore.kernel.org/qemu-devel/1599735398-6829-4-git-send-email-yi.l.liu@intel.com/
Reported-by: Eric Auger <eric.auger@redhat.com>
Fixes: b68ba1ca57
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210204191228.187550-1-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds trace events for virtio-pmem functionality.
Adding trace events for virtio pmem request, reponse and host
side fsync functionality.
Signed-off-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Message-Id: <20201117115705.32195-1-pankaj.gupta.linux@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Address space is destroyed without proper removal of its listeners with
current code. They are expected to be removed in
virtio_device_instance_finalize [1], but qemu calls it through
object_deinit, after address_space_destroy call through
device_set_realized [2].
Move it to virtio_device_unrealize, called before device_set_realized
[3] and making it symmetric with memory_listener_register in
virtio_device_realize.
v2: Delete no-op call of virtio_device_instance_finalize.
Add backtraces.
[1]
#0 virtio_device_instance_finalize (obj=0x555557de5120)
at /home/qemu/include/hw/virtio/virtio.h:71
#1 0x0000555555b703c9 in object_deinit (type=0x555556639860,
obj=<optimized out>) at ../qom/object.c:671
#2 object_finalize (data=0x555557de5120) at ../qom/object.c:685
#3 object_unref (objptr=0x555557de5120) at ../qom/object.c:1184
#4 0x0000555555b4de9d in bus_free_bus_child (kid=0x555557df0660)
at ../hw/core/qdev.c:55
#5 0x0000555555c65003 in call_rcu_thread (opaque=opaque@entry=0x0)
at ../util/rcu.c:281
Queued by:
#0 bus_remove_child (bus=0x555557de5098,
child=child@entry=0x555557de5120) at ../hw/core/qdev.c:60
#1 0x0000555555b4ee31 in device_unparent (obj=<optimized out>)
at ../hw/core/qdev.c:984
#2 0x0000555555b70465 in object_finalize_child_property (
obj=<optimized out>, name=<optimized out>, opaque=0x555557de5120)
at ../qom/object.c:1725
#3 0x0000555555b6fa17 in object_property_del_child (
child=0x555557de5120, obj=0x555557ddcf90) at ../qom/object.c:645
#4 object_unparent (obj=0x555557de5120) at ../qom/object.c:664
#5 0x0000555555b4c071 in bus_unparent (obj=<optimized out>)
at ../hw/core/bus.c:147
#6 0x0000555555b70465 in object_finalize_child_property (
obj=<optimized out>, name=<optimized out>, opaque=0x555557de5098)
at ../qom/object.c:1725
#7 0x0000555555b6fa17 in object_property_del_child (
child=0x555557de5098, obj=0x555557ddcf90) at ../qom/object.c:645
#8 object_unparent (obj=0x555557de5098) at ../qom/object.c:664
#9 0x0000555555b4ee19 in device_unparent (obj=<optimized out>)
at ../hw/core/qdev.c:981
#10 0x0000555555b70465 in object_finalize_child_property (
obj=<optimized out>, name=<optimized out>, opaque=0x555557ddcf90)
at ../qom/object.c:1725
#11 0x0000555555b6fa17 in object_property_del_child (
child=0x555557ddcf90, obj=0x55555685da10) at ../qom/object.c:645
#12 object_unparent (obj=0x555557ddcf90) at ../qom/object.c:664
#13 0x00005555558dc331 in pci_for_each_device_under_bus (
opaque=<optimized out>, fn=<optimized out>, bus=<optimized out>)
at ../hw/pci/pci.c:1654
[2]
Optimizer omits pci_qdev_unrealize, called by device_set_realized, and
do_pci_unregister_device, called by pci_qdev_unrealize and caller of
address_space_destroy.
#0 address_space_destroy (as=0x555557ddd1b8)
at ../softmmu/memory.c:2840
#1 0x0000555555b4fc53 in device_set_realized (obj=0x555557ddcf90,
value=<optimized out>, errp=0x7fffeea8f1e0)
at ../hw/core/qdev.c:850
#2 0x0000555555b6eaa6 in property_set_bool (obj=0x555557ddcf90,
v=<optimized out>, name=<optimized out>, opaque=0x555556650ba0,
errp=0x7fffeea8f1e0) at ../qom/object.c:2255
#3 0x0000555555b70e07 in object_property_set (
obj=obj@entry=0x555557ddcf90,
name=name@entry=0x555555db99df "realized",
v=v@entry=0x7fffe46b7500,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1400
#4 0x0000555555b73c5f in object_property_set_qobject (
obj=obj@entry=0x555557ddcf90,
name=name@entry=0x555555db99df "realized",
value=value@entry=0x7fffe44f6180,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/qom-qobject.c:28
#5 0x0000555555b71044 in object_property_set_bool (
obj=0x555557ddcf90, name=0x555555db99df "realized",
value=<optimized out>, errp=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1470
#6 0x0000555555921cb7 in pcie_unplug_device (bus=<optimized out>,
dev=0x555557ddcf90,
opaque=<optimized out>) at /home/qemu/include/hw/qdev-core.h:17
#7 0x00005555558dc331 in pci_for_each_device_under_bus (
opaque=<optimized out>, fn=<optimized out>,
bus=<optimized out>) at ../hw/pci/pci.c:1654
[3]
#0 virtio_device_unrealize (dev=0x555557de5120)
at ../hw/virtio/virtio.c:3680
#1 0x0000555555b4fc63 in device_set_realized (obj=0x555557de5120,
value=<optimized out>, errp=0x7fffee28df90)
at ../hw/core/qdev.c:850
#2 0x0000555555b6eab6 in property_set_bool (obj=0x555557de5120,
v=<optimized out>, name=<optimized out>, opaque=0x555556650ba0,
errp=0x7fffee28df90) at ../qom/object.c:2255
#3 0x0000555555b70e17 in object_property_set (
obj=obj@entry=0x555557de5120,
name=name@entry=0x555555db99ff "realized",
v=v@entry=0x7ffdd8035040,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1400
#4 0x0000555555b73c6f in object_property_set_qobject (
obj=obj@entry=0x555557de5120,
name=name@entry=0x555555db99ff "realized",
value=value@entry=0x7ffdd8035020,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/qom-qobject.c:28
#5 0x0000555555b71054 in object_property_set_bool (
obj=0x555557de5120, name=name@entry=0x555555db99ff "realized",
value=value@entry=false, errp=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1470
#6 0x0000555555b4edc5 in qdev_unrealize (dev=<optimized out>)
at ../hw/core/qdev.c:403
#7 0x0000555555b4c2a9 in bus_set_realized (obj=<optimized out>,
value=<optimized out>, errp=<optimized out>)
at ../hw/core/bus.c:204
#8 0x0000555555b6eab6 in property_set_bool (obj=0x555557de5098,
v=<optimized out>, name=<optimized out>, opaque=0x555557df04c0,
errp=0x7fffee28e0a0) at ../qom/object.c:2255
#9 0x0000555555b70e17 in object_property_set (
obj=obj@entry=0x555557de5098,
name=name@entry=0x555555db99ff "realized",
v=v@entry=0x7ffdd8034f50,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1400
#10 0x0000555555b73c6f in object_property_set_qobject (
obj=obj@entry=0x555557de5098,
name=name@entry=0x555555db99ff "realized",
value=value@entry=0x7ffdd8020630,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/qom-qobject.c:28
#11 0x0000555555b71054 in object_property_set_bool (
obj=obj@entry=0x555557de5098,
name=name@entry=0x555555db99ff "realized",
value=value@entry=false, errp=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1470
#12 0x0000555555b4c725 in qbus_unrealize (
bus=bus@entry=0x555557de5098) at ../hw/core/bus.c:178
#13 0x0000555555b4fc00 in device_set_realized (obj=0x555557ddcf90,
value=<optimized out>, errp=0x7fffee28e1e0)
at ../hw/core/qdev.c:844
#14 0x0000555555b6eab6 in property_set_bool (obj=0x555557ddcf90,
v=<optimized out>, name=<optimized out>, opaque=0x555556650ba0,
errp=0x7fffee28e1e0) at ../qom/object.c:2255
#15 0x0000555555b70e17 in object_property_set (
obj=obj@entry=0x555557ddcf90,
name=name@entry=0x555555db99ff "realized",
v=v@entry=0x7ffdd8020560,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1400
#16 0x0000555555b73c6f in object_property_set_qobject (
obj=obj@entry=0x555557ddcf90,
name=name@entry=0x555555db99ff "realized",
value=value@entry=0x7ffdd8020540,
errp=errp@entry=0x5555565bbf38 <error_abort>)
at ../qom/qom-qobject.c:28
#17 0x0000555555b71054 in object_property_set_bool (
obj=0x555557ddcf90, name=0x555555db99ff "realized",
value=<optimized out>, errp=0x5555565bbf38 <error_abort>)
at ../qom/object.c:1470
#18 0x0000555555921cb7 in pcie_unplug_device (bus=<optimized out>,
dev=0x555557ddcf90, opaque=<optimized out>)
at /home/qemu/include/hw/qdev-core.h:17
#19 0x00005555558dc331 in pci_for_each_device_under_bus (
opaque=<optimized out>, fn=<optimized out>, bus=<optimized out>)
at ../hw/pci/pci.c:1654
Fixes: c611c76417 ("virtio: add MemoryListener to cache ring translations")
Buglink: https://bugs.launchpad.net/qemu/+bug/1912846
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20210125192505.390554-1-eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the kernel, virtio_gpu_init() uses virtio_get_shm_region()
since
commit 6076a9711dc5 ("drm/virtio: implement blob resources: probe for host visible region")
but vm_get_shm_region() unconditionally uses VIRTIO_MMIO_SHM_SEL to
get the address and the length of the region.
commit 38e895487afc ("virtio: Implement get_shm_region for MMIO transport"
As this is not implemented in QEMU, address and length are 0 and passed
as is to devm_request_mem_region() that triggers a crash:
[drm:virtio_gpu_init] *ERROR* Could not reserve host visible region
Unable to handle kernel NULL pointer dereference at virtual address (ptrval)
According to the comments in the kernel, a non existent shared region
has a length of (u64)-1.
This is what we return now with this patch to disable the region.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20201220163539.2255963-1-laurent@vivier.eu>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 9d7bd0826f introduced a new 'use-disabled-flag' property
set to true by default.
To allow the migration, we set this property to false in the hw_compat,
but in the wrong place (hw_compat_4_1).
Since commit 9d7bd0826f was released with QEMU 5.0, we move
'use-disabled-flag' property to hw_compat_4_2, so 4.2 machine types
will have the pre-patch behavior and the migration can work.
The issue was discovered with vhost-vsock device and 4.2 machine
type without running any kernel in the VM:
$ qemu-4.2 -M pc-q35-4.2,accel=kvm \
-device vhost-vsock-pci,guest-cid=4 \
-monitor stdio -incoming tcp:0:3333
$ qemu-5.2 -M pc-q35-4.2,accel=kvm \
-device vhost-vsock-pci,guest-cid=3 \
-monitor stdio
(qemu) migrate -d tcp:0:3333
# qemu-4.2 output
qemu-system-x86_64: Failed to load virtio-vhost_vsock:virtio
qemu-system-x86_64: error while loading state for instance 0x0 of device '0000:00:03.0/virtio-vhost_vsock'
qemu-system-x86_64: load of migration failed: No such file or directory
Reported-by: Jing Zhao <jinzhao@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1907255
Fixes: 9d7bd0826f ("virtio-pci: disable vring processing when bus-mastering is disabled")
Cc: mdroth@linux.vnet.ibm.com
CC: qemu-stable@nongnu.org
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210108171252.209502-1-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This property can be useful for distros to set up known-good ROM sizes for
migration purposes. The VM will fail to start if the ROM is too large,
and migration compatibility will not be broken if the ROM is too small.
Note that even though romsize is a uint32_t, it has to be between 1
(because empty ROM files are not accepted, and romsize must be greater
than the file) and 2^31 (because values above are not powers of two and
are rejected).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201218182736.1634344-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210203131828.156467-3-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
get_image_size() returns an int64_t, which pci_add_option_rom() assigns
to an "int" without any range checking. A 32-bit BAR could be up to
2 GiB in size, so reject anything above it. In order to accomodate
a rounded-up size of 2 GiB, change pci_patch_ids's size argument
to unsigned.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210203131828.156467-2-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Displaying rendered resources requires blocking qemu GPU to avoid extra
framebuffer copies. For an external display, via Spice currently, there
is a callback to block/unblock the rendering in the same thread.
But with the vhost-user-gpu backend, the qemu process doesn't handle
the rendering itself, and the blocking callback isn't effective.
Instead, the backend must be notified when the display code is done.
Fix this by adding a new GraphicHwOps callback to indicate the GL state
is flushed, and we are done manipulating the shared GL resources. Call
it from gtk and spice display.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-19-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The next patch will notify the GL context got flush, which will resume
the queue processing. However, if this happens within the caller
context, it will end up with a stack overflow flush/update loop.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-18-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Those flags can be used to express different requirements for the
display or other needs.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-12-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This check is currently limited. It only is used by vhost-user-gpu (not
by vfio-display), and will print an error repeatedly during run-time.
We are going to dissociate the GL context from the
DisplayChangeListener, and listeners may come and go. The following
patches will address this differently.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-10-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
EDID has been enabled by default, but the backend may not implement
it (such as the contrib backend). This results in extra warnings and
potentially other issues in the guest.
The option shouldn't probably have been added to VIRTIO_GPU_BASE, but
it's a bit too late now, report an error and disable EDID when it's
not available.
Fixes: 0a7196625 ("edid: flip the default to enabled")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210204105232.834642-2-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Asynchronous handlers may be waiting for the graphic_hw_update_done() to
be called in this case too.
Fixes: 4d6316218 ("console: add graphic_hw_update_done()")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210201201422.446552-3-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On secondary QXL devices, the console is only set on qxl.vga.con. But
graphic_hw_update_done() is called with qxl.ssd.dcl.con.
Like for primary QXL devices, set qxl.sdd.dcl.con = qxl.vga.con.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210201201422.446552-2-marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201119025851.56487-1-alex.chen@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Most of ARM machines display their CPU when QEMU list the available
machines (-M help). Some machines do not. Fix to unify the help
output.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a dependency XLNX_ZYNQMP -> PTIMER to fix:
/usr/bin/ld:
libcommon.fa.p/hw_net_can_xlnx-zynqmp-can.c.o: in function `xlnx_zynqmp_can_realize':
hw/net/can/xlnx-zynqmp-can.c:1082: undefined reference to `ptimer_init'
hw/net/can/xlnx-zynqmp-can.c:1085: undefined reference to `ptimer_transaction_begin'
hw/net/can/xlnx-zynqmp-can.c:1087: undefined reference to `ptimer_set_freq'
hw/net/can/xlnx-zynqmp-can.c:1088: undefined reference to `ptimer_set_limit'
hw/net/can/xlnx-zynqmp-can.c:1089: undefined reference to `ptimer_run'
hw/net/can/xlnx-zynqmp-can.c:1090: undefined reference to `ptimer_transaction_commit'
libcommon.fa.p/hw_net_can_xlnx-zynqmp-can.c.o:(.data.rel+0x2c8): undefined reference to `vmstate_ptimer'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Versal SoC instantiates the TYPE_XLNX_ZYNQMP_RTC object in
versal_create_rtc()(). Select CONFIG_XLNX_ZYNQMP to fix:
$ make check-qtest-aarch64
...
Running test qtest-aarch64/qom-test
qemu-system-aarch64: missing object type 'xlnx-zynmp.rtc'
Broken pipe
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Versal SoC instantiates the TYPE_XLNX_ZDMA object in
versal_create_admas(). Introduce the XLNX_ZDMA configuration
and select it to fix:
$ qemu-system-aarch64 -M xlnx-versal-virt ...
qemu-system-aarch64: missing object type 'xlnx.zdma'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Exynos4210 SoC uses an OR gate on the PL330 IRQ lines.
Fixes: dab15fbe2a ("hw/arm/exynos4210: Fix DMA initialization")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210131184449.382425-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The STM32F405 SoC uses an OR gate on its ADC IRQs.
Fixes: 529fc5fd3e ("hw/arm: Add the STM32F4xx SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the ARM Generic Interrupt Controller Architecture specification
(document "ARM IHI 0048B.b (ID072613)"), the SGIINTID field is 4 bit,
not 10:
- 4.3 Distributor register descriptions
- 4.3.15 Software Generated Interrupt Register, GICD_SG
- Table 4-21 GICD_SGIR bit assignments
The Interrupt ID of the SGI to forward to the specified CPU
interfaces. The value of this field is the Interrupt ID, in
the range 0-15, for example a value of 0b0011 specifies
Interrupt ID 3.
Correct the irq mask to fix an undefined behavior (which eventually
lead to a heap-buffer-overflow, see [Buglink]):
$ echo 'writel 0x8000f00 0xff4affb0' | qemu-system-aarch64 -M virt,accel=qtest -qtest stdio
[I 1612088147.116987] OPENED
[R +0.278293] writel 0x8000f00 0xff4affb0
../hw/intc/arm_gic.c:1498:13: runtime error: index 944 out of bounds for type 'uint8_t [16][8]'
SUMMARY: UndefinedBehaviorSanitizer: undefined-behavior ../hw/intc/arm_gic.c:1498:13
This fixes a security issue when running with KVM on Arm with
kernel-irqchip=off. (The default is kernel-irqchip=on, which is
unaffected, and which is also the correct choice for performance.)
Cc: qemu-stable@nongnu.org
Fixes: CVE-2021-20221
Fixes: 9ee6e8bb85 ("ARMv7 support.")
Buglink: https://bugs.launchpad.net/qemu/+bug/1913916
Buglink: https://bugs.launchpad.net/qemu/+bug/1913917
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210131103401.217160-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The endianness of data exchange between tx and rx fifo is incorrect.
Earlier bytes are supposed to show up on MSB and later bytes on LSB,
ie: in big endian. The manual does not explicitly say this, but the
U-Boot and Linux driver codes have a swap on the data transferred
to tx fifo and from rx fifo.
With this change, U-Boot read from / write to SPI flash tests pass.
=> sf test 1ff000 1000
SPI flash test:
0 erase: 0 ticks, 4096000 KiB/s 32768.000 Mbps
1 check: 3 ticks, 1333 KiB/s 10.664 Mbps
2 write: 235 ticks, 17 KiB/s 0.136 Mbps
3 read: 2 ticks, 2000 KiB/s 16.000 Mbps
Test passed
0 erase: 0 ticks, 4096000 KiB/s 32768.000 Mbps
1 check: 3 ticks, 1333 KiB/s 10.664 Mbps
2 write: 235 ticks, 17 KiB/s 0.136 Mbps
3 read: 2 ticks, 2000 KiB/s 16.000 Mbps
Fixes: c906a3a015 ("i.MX: Add the Freescale SPI Controller")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210129132323.30946-11-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the ECSPIx_CONREG register BURST_LENGTH field, the manual says:
0x020 A SPI burst contains the 1 LSB in first word and all 32 bits in second word.
0x021 A SPI burst contains the 2 LSB in first word and all 32 bits in second word.
Current logic uses either s->burst_length or 32, whichever smaller,
to determine how many bits it should read from the tx fifo each time.
For example, for a 48 bit burst length, current logic transfers the
first 32 bit from the first word in the tx fifo, followed by a 16
bit from the second word in the tx fifo, which is wrong. The correct
logic should be: transfer the first 16 bit from the first word in
the tx fifo, followed by a 32 bit from the second word in the tx fifo.
With this change, SPI flash can be successfully probed by U-Boot on
imx6 sabrelite board.
=> sf probe
SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB
Fixes: c906a3a015 ("i.MX: Add the Freescale SPI Controller")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210129132323.30946-10-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current implementation of the imx spi controller expects the burst
length to be multiple of 8, which is the most common use case.
In case the burst length is not what we expect, log it to give user
a chance to notice it, and round it up to be multiple of 8.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210129132323.30946-9-bmeng.cn@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a write to ECSPI_CONREG register to disable the SPI controller,
imx_spi_soft_reset() is called to reset the controller, but chip
select lines should have been disabled, otherwise the state machine
of any devices (e.g.: SPI flashes) connected to the SPI master is
stuck to its last state and responds incorrectly to any follow-up
commands.
Fixes: c906a3a015 ("i.MX: Add the Freescale SPI Controller")
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210129132323.30946-8-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the block is disabled, only the ECSPI_CONREG register can
be modified. Setting the EN bit enabled the device, clearing it
"disables the block and resets the internal logic with the
exception of the ECSPI_CONREG" register.
Ignore all other registers write except ECSPI_CONREG when the
block is disabled.
Ref: i.MX 6DQ Applications Processor Reference Manual (IMX6DQRM),
chapter 21.7.3: Control Register (ECSPIx_CONREG)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210129132323.30946-7-bmeng.cn@gmail.com
Message-Id: <20210115153049.3353008-6-f4bug@amsat.org>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the block is disabled, it stay it is 'internal reset logic'
(internal clocks are gated off). Reading any register returns
its reset value. Only update this value if the device is enabled.
Ref: i.MX 6DQ Applications Processor Reference Manual (IMX6DQRM),
chapter 21.7.3: Control Register (ECSPIx_CONREG)
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210129132323.30946-6-bmeng.cn@gmail.com
Message-Id: <20210115153049.3353008-5-f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the block is disabled, all registers are reset with the
exception of the ECSPI_CONREG. It is initialized to zero
when the instance is created.
Ref: i.MX 6DQ Applications Processor Reference Manual (IMX6DQRM),
chapter 21.7.3: Control Register (ECSPIx_CONREG)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210129132323.30946-5-bmeng.cn@gmail.com
[bmeng: add a 'common_reset' function that does most of reset operation]
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'burst_length' is cleared in imx_spi_reset(), which is called
after imx_spi_realize(). Remove the initialization to simplify.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210129132323.30946-4-bmeng.cn@gmail.com
Message-Id: <20210115153049.3353008-3-f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Usually the approach is that the device on the other end of the line
is going to reset its state anyway, so there's no need to actively
signal an irq line change during the reset hook.
Move imx_spi_update_irq() out of imx_spi_reset(), to a new function
imx_spi_soft_reset() that is called when the controller is disabled.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210129132323.30946-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Avoid using a magic number (4) everywhere for the number of chip
selects supported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 20210129132323.30946-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When handling guest range-based IOTLB invalidation, we should decode the TG
field into the corresponding translation granule size so that we can pass
the correct invalidation range to backend. Set @granule to (tg * 2 + 10) to
properly emulate the architecture.
Fixes: d52915616c ("hw/arm/smmuv3: Get prepared for range invalidation")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210130043220.1345-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the frontend device has no space for a read the fd is removed
from polling to allow time for the guest to read and clear the buffer.
Without the call to qemu_chr_fe_accept_input(), the poll will not be
broken out of when the guest has cleared the buffer causing significant
IO delays that get worse with smaller buffers.
Buglink: https://bugs.launchpad.net/qemu/+bug/1913341
Signed-off-by: Iris Johnson <iris@modwiz.com>
Message-id: 20210130184016.1787097-1-iris@modwiz.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the Exynos 4210 UART code always reports available FIFO space
when the backend checks for buffer space. When the FIFO is disabled this
is behavior causes the backend chardev code to replace the data before the
guest can read it.
This patch changes adds the logic to report the capacity properly when the
FIFO is not being used.
Buglink: https://bugs.launchpad.net/qemu/+bug/1913344
Signed-off-by: Iris Johnson <iris@modwiz.com>
Message-id: 20210128033655.1029577-1-iris@modwiz.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Alexander reported an issue in gic_get_current_cpu() using the
fuzzer. Yet another "deref current_cpu with QTest" bug, reproducible
doing:
$ echo readb 0xf03ff000 | qemu-system-arm -M npcm750-evb,accel=qtest -qtest stdio
[I 1611849440.651452] OPENED
[R +0.242498] readb 0xf03ff000
hw/intc/arm_gic.c:63:29: runtime error: member access within null pointer of type 'CPUState' (aka 'struct CPUState')
SUMMARY: UndefinedBehaviorSanitizer: undefined-behavior hw/intc/arm_gic.c:63:29 in
AddressSanitizer:DEADLYSIGNAL
=================================================================
==3719691==ERROR: AddressSanitizer: SEGV on unknown address 0x0000000082a0 (pc 0x5618790ac882 bp 0x7ffca946f4f0 sp 0x7ffca946f4a0 T0)
==3719691==The signal is caused by a READ memory access.
#0 0x5618790ac882 in gic_get_current_cpu hw/intc/arm_gic.c:63:29
#1 0x5618790a8901 in gic_dist_readb hw/intc/arm_gic.c:955:11
#2 0x5618790a7489 in gic_dist_read hw/intc/arm_gic.c:1158:17
#3 0x56187adc573b in memory_region_read_with_attrs_accessor softmmu/memory.c:464:9
#4 0x56187ad7903a in access_with_adjusted_size softmmu/memory.c:552:18
#5 0x56187ad766d6 in memory_region_dispatch_read1 softmmu/memory.c:1426:16
#6 0x56187ad758a8 in memory_region_dispatch_read softmmu/memory.c:1449:9
#7 0x56187b09e84c in flatview_read_continue softmmu/physmem.c:2822:23
#8 0x56187b0a0115 in flatview_read softmmu/physmem.c:2862:12
#9 0x56187b09fc9e in address_space_read_full softmmu/physmem.c:2875:18
#10 0x56187aa88633 in address_space_read include/exec/memory.h:2489:18
#11 0x56187aa88633 in qtest_process_command softmmu/qtest.c:558:13
#12 0x56187aa81881 in qtest_process_inbuf softmmu/qtest.c:797:9
#13 0x56187aa80e02 in qtest_read softmmu/qtest.c:809:5
current_cpu is NULL because QTest accelerator does not use CPU.
Fix by skipping the check and returning the first CPU index when
QTest accelerator is used, similarly to commit c781a2cc42
("hw/i386/vmport: Allow QTest use without crashing").
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Message-id: 20210128161417.3726358-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Check that -device nvdimm,unarmed=on is used when -object
memory-backend-file,readonly=on and document that -device
nvdimm,unarmed=on|off controls whether the NVDIMM appears read-only to
the guest.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20210104171320.575838-4-stefanha@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Now that the watchdog device uses its Clock input rather than being
passed the value of system_clock_scale at creation time, we can
remove the hack where we reset the STELLARIS_SYS at board creation
time to force it to set system_clock_scale. Instead it will be reset
at the usual point in startup and will inform the watchdog of the
clock frequency at that point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-26-peter.maydell@linaro.org
Message-id: 20210121190622.22000-26-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now no users are setting the frq properties on the CMSDK timer,
dualtimer, watchdog or ARMSSE SoC devices, we can remove the
properties and the struct fields that back them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-25-peter.maydell@linaro.org
Message-id: 20210121190622.22000-25-peter.maydell@linaro.org
Remove all the code that sets frequency properties on the CMSDK
timer, dualtimer and watchdog devices and on the ARMSSE SoC device:
these properties are unused now that the devices rely on their Clock
inputs instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-24-peter.maydell@linaro.org
Message-id: 20210121190622.22000-24-peter.maydell@linaro.org
Use the MAINCLK Clock input to set the system_clock_scale variable
rather than using the mainclk_frq property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210128114145.20536-23-peter.maydell@linaro.org
Message-id: 20210121190622.22000-23-peter.maydell@linaro.org
Switch the CMSDK APB watchdog device over to using its Clock input;
the wdogclk_frq property is now ignored.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-21-peter.maydell@linaro.org
Message-id: 20210121190622.22000-21-peter.maydell@linaro.org
Switch the CMSDK APB dualtimer device over to using its Clock input;
the pclk-frq property is now ignored.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-20-peter.maydell@linaro.org
Message-id: 20210121190622.22000-20-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Switch the CMSDK APB timer device over to using its Clock input; the
pclk-frq property is now ignored.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-19-peter.maydell@linaro.org
Message-id: 20210121190622.22000-19-peter.maydell@linaro.org
Create and connect the Clock input for the watchdog device on the
Stellaris boards. Because the Stellaris boards model the ability to
change the clock rate by programming PLL registers, we have to create
an output Clock on the ssys_state device and wire it up to the
watchdog.
Note that the old comment on ssys_calculate_system_clock() got the
units wrong -- system_clock_scale is in nanoseconds, not
milliseconds. Improve the commentary to clarify how we are
calculating the period.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-18-peter.maydell@linaro.org
Message-id: 20210121190622.22000-18-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Convert the SSYS code in the Stellaris boards (which encapsulates the
system registers) to a proper QOM device. This will provide us with
somewhere to put the output Clock whose frequency depends on the
setting of the PLL configuration registers.
This is a migration compatibility break for lm3s811evb, lm3s6965evb.
We use 3-phase reset here because the Clock will need to propagate
its value in the hold phase.
For the moment we reset the device during the board creation so that
the system_clock_scale global gets set; this will be removed in a
subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-17-peter.maydell@linaro.org
Message-id: 20210121190622.22000-17-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Create a fixed-frequency Clock object to be the SYSCLK, and wire it
up to the devices that require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-14-peter.maydell@linaro.org
Message-id: 20210121190622.22000-14-peter.maydell@linaro.org
The old-style convenience function cmsdk_apb_timer_create() for
creating CMSDK_APB_TIMER objects is used in only two places in
mps2.c. Most of the rest of the code in that file uses the new
"initialize in place" coding style.
We want to connect up a Clock object which should be done between the
object creation and realization; rather than adding a Clock* argument
to the convenience function, convert the timer creation code in
mps2.c to the same style as is used already for the watchdog,
dualtimer and other devices, and delete the now-unused convenience
function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-13-peter.maydell@linaro.org
Message-id: 20210121190622.22000-13-peter.maydell@linaro.org
Create two input clocks on the ARMSSE devices, one for the normal
MAINCLK, and one for the 32KHz S32KCLK, and wire these up to the
appropriate devices. The old property-based clock frequency setting
will remain in place until conversion is complete.
This is a migration compatibility break for machines mps2-an505,
mps2-an521, musca-a, musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-12-peter.maydell@linaro.org
Message-id: 20210121190622.22000-12-peter.maydell@linaro.org
While we transition the ARMSSE code from integer properties
specifying clock frequencies to Clock objects, we want to have the
device provide both at once. We want the final name of the main
input Clock to be "MAINCLK", following the hardware name.
Unfortunately creating an input Clock with a name X creates an
under-the-hood QOM property X; for "MAINCLK" this clashes with the
existing UINT32 property of that name.
Rename the UINT32 property to MAINCLK_FRQ so it can coexist with the
MAINCLK Clock; once the transition is complete MAINCLK_FRQ will be
deleted.
Commit created with:
perl -p -i -e 's/MAINCLK/MAINCLK_FRQ/g' hw/arm/{armsse,mps2-tz,musca}.c include/hw/arm/armsse.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-11-peter.maydell@linaro.org
Message-id: 20210121190622.22000-11-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_TIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the
wdogclk-frq property to using the Clock once all the users of this
device have been converted to wire up the Clock.
This is a migration compatibility break for machines mps2-an385,
mps2-an386, mps2-an500, mps2-an511, mps2-an505, mps2-an521, musca-a,
musca-b1, lm3s811evb, lm3s6965evb.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-10-peter.maydell@linaro.org
Message-id: 20210121190622.22000-10-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_DUALTIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the pclk-frq
property to using the Clock once all the users of this device have
been converted to wire up the Clock.
We take the opportunity to correct the name of the clock input to
match the hardware -- the dual timer names the clock which drives the
timers TIMCLK. (It does also have a 'pclk' input, which is used only
for the register and APB bus logic; on the SSE-200 these clocks are
both connected together.)
This is a migration compatibility break for machines mps2-an385,
mps2-an386, mps2-an500, mps2-an511, mps2-an505, mps2-an521, musca-a,
musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-9-peter.maydell@linaro.org
Message-id: 20210121190622.22000-9-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_TIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the pclk-frq
property to using the Clock once all the users of this device have
been converted to wire up the Clock.
Since the device doesn't already have a doc comment for its "QEMU
interface", we add one including the new Clock.
This is a migration compatibility break for machines mps2-an505,
mps2-an521, musca-a, musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-8-peter.maydell@linaro.org
Message-id: 20210121190622.22000-8-peter.maydell@linaro.org
The state struct for the CMSDK APB timer device doesn't follow our
usual naming convention of camelcase -- "CMSDK" and "APB" are both
acronyms, but "TIMER" is not so should not be all-uppercase.
Globally rename the struct to "CMSDKAPBTimer" (bringing it into line
with CMSDKAPBWatchdog and CMSDKAPBDualTimer; CMSDKAPBUART remains
as-is because "UART" is an acronym).
Commit created with:
perl -p -i -e 's/CMSDKAPBTIMER/CMSDKAPBTimer/g' hw/timer/cmsdk-apb-timer.c include/hw/arm/armsse.h include/hw/timer/cmsdk-apb-timer.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-7-peter.maydell@linaro.org
Message-id: 20210121190622.22000-7-peter.maydell@linaro.org
The ptimer API currently provides two methods for setting the period:
ptimer_set_period(), which takes a period in nanoseconds, and
ptimer_set_freq(), which takes a frequency in Hz. Neither of these
lines up nicely with the Clock API, because although both the Clock
and the ptimer track the frequency using a representation of whole
and fractional nanoseconds, conversion via either period-in-ns or
frequency-in-Hz will introduce a rounding error.
Add a new function ptimer_set_period_from_clock() which takes the
Clock object directly to avoid the rounding issues. This includes a
facility for the user to specify that there is a frequency divider
between the Clock proper and the timer, as some timer devices like
the CMSDK APB dualtimer need this.
To avoid having to drag in clock.h from ptimer.h we add the Clock
type to typedefs.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-2-peter.maydell@linaro.org
Message-id: 20210121190622.22000-2-peter.maydell@linaro.org
Add PCI interface support for PVPANIC device. Create a new file pvpanic-pci.c
where the PCI specific routines reside and update the build system with the new
files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To ease the PCI device addition in next patches, split the code as follows:
- generic code (read/write/setup) is being kept in pvpanic.c
- ISA dependent code moved to pvpanic-isa.c
Also, rename:
- ISA_PVPANIC_DEVICE -> PVPANIC_ISA_DEVICE.
- TYPE_PVPANIC -> TYPE_PVPANIC_ISA.
- MemoryRegion io -> mr.
- pvpanic_ioport_* in pvpanic_*.
Update the build system with the new files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix potential overflow problem when calculating pwm_duty.
1. Ensure p->cmr and p->cnr to be from [0,65535], according to the
hardware specification.
2. Changed duty to uint32_t. However, since MAX_DUTY * (p->cmr+1)
can excceed UINT32_MAX, we convert them to uint64_t in computation
and converted them back to uint32_t.
(duty is guaranteed to be <= MAX_DUTY so it won't overflow.)
Fixes: CID 1442342
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Doug Evans <dje@google.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210127011142.2122790-1-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add secure pl061 for reset/power down machine from
the secure world (Arm Trusted Firmware). Connect it
with gpio-pwr driver.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
[PMM: Added mention of the new device to the documentation]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No functional change. Just refactor code to better
support secure and normal world gpios.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement gpio-pwr driver to allow reboot and poweroff machine.
This is simple driver with just 2 gpios lines. Current use case
is to reboot and poweroff virt machine in secure mode. Secure
pl066 gpio chip is needed for that.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The properties to attach a CANBUS object to the xlnx-zcu102 machine have
a period in them. We want to use periods in properties for compound QAPI types,
and besides the "xlnx-zcu102." prefix is both unnecessary and different
from any other machine property name. Remove it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20210118162537.779542-1-pbonzini@redhat.com
Reviewed-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Fix crash on write to read-only devices
- iotests: Rewrite 'check' in Python, get rid of 'groups' and allow
non-numeric test case names
-----BEGIN PGP SIGNATURE-----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=gFsg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Fix crash on write to read-only devices
- iotests: Rewrite 'check' in Python, get rid of 'groups' and allow
non-numeric test case names
# gpg: Signature made Wed 27 Jan 2021 19:56:00 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
iotests: rename and move 169 and 199 tests
iotests: rewrite check into python
iotests: add testrunner.py
iotests: add testenv.py
iotests: add findtests.py
iotests: 146: drop extra whitespaces from .out file
virtio-scsi-test: Test writing to scsi-cd device
block: Separate blk_is_writable() and blk_supports_write_perm()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These cases require a bit more thought to review; in each case, the
code was appending to a list, but not with a FOOList **tail variable.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210113221013.390592-6-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Flawed change to qmp_guest_network_get_interfaces() dropped]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The easiest spots to use QAPI_LIST_APPEND are where we already have an
obvious pointer to the tail of a list. While at it, consistently use
the variable name 'tail' for that purpose.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210113221013.390592-5-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Commit 54aa3de72e switched multiple sites to use QAPI_LIST_PREPEND
instead of open-coding, but missed a couple of spots.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210113221013.390592-3-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In commit 2f487a3d40 we fixed a problem observed with using the
vmware-vga device and the VNC UI frontend in a belt-and-braces
manner:
* we made the VNC frontend handle non-multiple-of-16 surface widths
* we rounded up the vmware-vga display width to a multiple of 16
However this introduced a spurious dependency of a device model on a
UI frontend header. vmware-vga isn't special and should not care
about what UI frontend it is using, and the VNC frontend needs to
handle arbitrary surface widths because other display device models
could use them. Moreover, even if the maximum width in vmware-vga is
made a multiple of 16, the guest itself can always program a
different width.
Remove the dependency on the VNC header. Since we have been using
the rounded-up width value since 2014, stick with it rather than
introducing a behaviour change, but don't calculate it by rounding up
to VNC_DIRTY_BITS_PER_PIXEL any more.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210112161608.16055-1-peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Linking of qemu-system-ppc64 fails on macOS with dtrace enabled:
error: probe tpm_spapr_show_buffer doesn't exist
error: Could not register probes
ld: error creating dtrace DOF section for architecture x86_64
The failure is explained in 8c8ed03850 ("net/colo: Match is-enabled
probe to tracepoint"). In short, is-enabled probe can't be used without
a matching trace probe. And for this particular case
tpm_util_show_buffer probe should be enabled to print TPM buffer.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Version: GnuPG v1
iQEcBAABAgAGBQJgDonvAAoJEO8Ells5jWIR++8IAJBTpKDSwdwG1ySn5m6tHZHM
GdFD2Ao8R8VsonJzw9i/1Gfn9T0icndRU6VC+nJEdvSLXUDoAQdmMmLCk4oml41g
gzPzsc6bFKwKB4DG3RyixbEoUsMl7jQRoVYOgWy1Ezx2daAGG9PjuDMdBU4tNCFv
IxkVpOz3RClhzaMz3O0OkLKljooRcvhePB+8FuZCOnBzxDJ9RU1KXDpv5kYMswFL
9f+D2UK474IcaAQCzKXuHrs/k3utMEY32udjqQdgb9y/8jZYJuEZSB7pyXozuSAO
QSl62FxbAwfx85hVbMqnIa2Yd629SiVVHsotavAZz60fcBaQgrNbBTWDNlCrWJo=
=XN54
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 25 Jan 2021 09:05:51 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: checksum: Introduce fine control over checksum type
net: checksum: Add IP header checksum calculation
net: checksum: Skip fragmented IP packets
net: Fix handling of id in netdev_add and netdev_del
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Various improvements for SD cards in SPI mode (Bin Meng)
-----BEGIN PGP SIGNATURE-----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=B3sY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/sdmmc-20210124' into staging
SD/MMC patches
- Various improvements for SD cards in SPI mode (Bin Meng)
# gpg: Signature made Sun 24 Jan 2021 19:16:55 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/sdmmc-20210124:
hw/sd: sd.h: Cosmetic change of using spaces
hw/sd: ssi-sd: Use macros for the dummy value and tokens in the transfer
hw/sd: ssi-sd: Fix the wrong command index for STOP_TRANSMISSION
hw/sd: ssi-sd: Add a state representing Nac
hw/sd: ssi-sd: Suffix a data block with CRC16
util: Add CRC16 (CCITT) calculation routines
hw/sd: sd: Drop sd_crc16()
hw/sd: sd: Support CMD59 for SPI mode
hw/sd: ssi-sd: Fix incorrect card response sequence
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present net_checksum_calculate() blindly calculates all types of
checksums (IP, TCP, UDP). Some NICs may have a per type setting in
their BDs to control what checksum should be offloaded. To support
such hardware behavior, introduce a 'csum_flag' parameter to the
net_checksum_calculate() API to allow fine control over what type
checksum is calculated.
Existing users of this API are updated accordingly.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
At present the codes use hardcoded numbers (0xff/0xfe) for the dummy
value and block start token. Replace them with macros.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-12-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This fixes the wrong command index for STOP_TRANSMISSION, the
required command to interrupt the multiple block read command,
in the old codes. It should be CMD12 (0x4c), not CMD13 (0x4d).
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.2,
"Data Read", there is a minimum 8 clock cycles (Nac) after the card
response and before data block shows up on the data out line. This
applies to both single and multiple block read operations.
Current implementation of single block read already satisfies the
timing requirement as in the RESPONSE state after all responses are
transferred the state remains unchanged. In the next 8 clock cycles
it jumps to DATA_START state if data is ready.
However we need an explicit state when expanding our support to
multiple block read in the future. Let's add a new state PREP_DATA
explicitly in the ssi-sd state machine to represent Nac.
Note we don't change the single block read state machine to let it
jump from RESPONSE state to DATA_START state as that effectively
generates a 16 clock cycles Nac, which might not be safe. As the
spec says the maximum Nac shall be calculated from several fields
encoded in the CSD register, we don't want to bother updating CSD
to ensure our Nac is within range to complicate things.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-9-bmeng.cn@gmail.com>
[PMD: Change VMState version id 4 -> 5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the SD spec, a valid data block is suffixed with a 16-bit CRC
generated by the standard CCITT polynomial x16+x12+x5+1. This part
is currently missing in the ssi-sd state machine. Without it, all
data block transfer fails in guest software because the expected
CRC16 is missing on the data out line.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-8-bmeng.cn@gmail.com>
[PMD: Change VMState version id 3 -> 4,
check s->mode validity in post_load()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
commit f6fb1f9b31 ("sdcard: Correct CRC16 offset in sd_function_switch()")
changed the 16-bit CRC to be stored at offset 64. In fact, this CRC
calculation is completely wrong. From the original codes, it wants
to calculate the CRC16 of the first 64 bytes of sd->data[], however
passing 64 as the `width` to sd_crc16() actually counts 256 bytes
starting from the `message` for the CRC16 calculation, which is not
what we want.
Besides that, it seems existing sd_crc16() algorithm does not match
the SD spec, which says CRC16 is the CCITT one but the calculation
does not produce expected result. It turns out the CRC16 was never
transferred outside the sd core, as in sd_read_byte() we see:
if (sd->data_offset >= 64)
sd->state = sd_transfer_state;
Given above reasons, let's drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
After the card is put into SPI mode, CRC check for all commands
including CMD0 will be done according to CMD59 setting. But this
command is currently unimplemented. Simply allow the decoding of
CMD59, but the CRC remains unchecked.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.1,
"Command/Response", there is a minimum 8 clock cycles (Ncr) before
the card response shows up on the data out line. However current
implementation jumps directly to the sending response state after
all 6 bytes command is received, which is a spec violation.
Add a new state PREP_RESP in the ssi-sd state machine to handle it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-4-bmeng.cn@gmail.com>
[PMD: Change VMState version id 2 -> 3]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
While processing ATAPI cmd_read/cmd_read_cd commands,
Logical Block Address (LBA) maybe invalid OR closer to the last block,
leading to an OOB access issues. Add range check to avoid it.
Fixes: CVE-2020-29443
Reported-by: Wenxiang Qian <leonwxqian@gmail.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20210118115130.457044-1-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use QSLIST instead of open-coding for a slightly improved readability.
No behavioral change.
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <20210122143514.215780-1-groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
If a fid was actually re-opened by v9fs_reopen_fid(), we re-traverse the
fid list from the head in case some other request created a fid that
needs to be marked unreclaimable as well (i.e. the client opened a new
handle on the path that is being unlinked). This is suboptimal since
most if not all fids that require it have likely been taken care of
already.
This is mostly the result of new fids being added to the head of the
list. Since the list is now a QSIMPLEQ, add new fids at the end instead
to avoid the need to rewind. Take a reference on the fid to ensure it
doesn't go away during v9fs_reopen_fid() and that it can be safely
passed to QSIMPLEQ_NEXT() afterwards. Since the associated put_fid()
can also yield, same is done with the next fid. So the logic here is
to get a reference on a fid and only put it back during the next
iteration after we could get a reference on the next fid.
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <20210121181510.1459390-1-groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Handle host superspeedplus (usb 3.1+) devices like superspeed (usb 3.0)
devices. That is enough to get them handled properly by xhci. They show
up as superspeed devices inside the guest, but should be able to actually
run at higher speeds.
Reported-by: Angel Pagan <Angel.Pagan@stratus.com>
Tested-by: Angel Pagan <Angel.Pagan@stratus.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210121150832.3564097-1-kraxel@redhat.com>
Log all traffic of a specific usb device to a pcap file for later
inspection. File format is compatible with linux usb monitor.
Usage:
qemu -device usb-${somedevice},pcap=file.pcap
wireshark file.pcap
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210119194452.2148048-1-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We are not ready to handle additional CDB data.
If a guest sends a packet with such additional data,
report the command parameter as not supported.
Specify a size (of 1 byte) for the add_cdb member we
are not using, to fix the following warning:
usb/dev-uas.c:157:31: error: field 'status' with variable sized type 'uas_iu' not at the end of a struct or class is a GNU extension [-Werror,-Wgnu-variable-sized-type-not-at-end]
uas_iu status;
^
Reported-by: Ed Maste <emaste@FreeBSD.org>
Reported-by: Daniele Buono <dbuono@linux.vnet.ibm.com>
Reported-by: Han Han <hhan@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210120153522.1173897-4-philmd@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
For some reason the assert() added in commit ccb799313a
("hw/usb: avoid format truncation warning when formatting
port name") does not fix when building with GCC 10.
KISS and expand the buffer by 4 bytes to silent the following
error when using GCC 10.2.1 on Fedora 33:
hw/usb/hcd-xhci.c: In function 'usb_xhci_realize':
hw/usb/hcd-xhci.c:3309:54: error: '%d' directive output may be truncated writing between 1 and 8 bytes into a region of size 5 [-Werror=format-truncation=]
3309 | snprintf(port->name, sizeof(port->name), "usb2 port #%d", i+1);
| ^~~~~~~~~~~~~~~
hw/usb/hcd-xhci.c:3309:54: note: directive argument in the range [1, 89478486]
In file included from /usr/include/stdio.h:866,
from include/qemu/osdep.h:85,
from hw/usb/hcd-xhci.c:22:
/usr/include/bits/stdio2.h:70:10: note: '__builtin___snprintf_chk' output between 13 and 20 bytes into a destination of size 16
70 | return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
71 | __bos (__s), __fmt, __va_arg_pack ());
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/usb/hcd-xhci.c:3323:54: error: '%d' directive output may be truncated writing between 1 and 8 bytes into a region of size 5 [-Werror=format-truncation=]
3323 | snprintf(port->name, sizeof(port->name), "usb3 port #%d", i+1);
| ^~~~~~~~~~~~~~~
hw/usb/hcd-xhci.c:3323:54: note: directive argument in the range [1, 89478486]
In file included from /usr/include/stdio.h:866,
from include/qemu/osdep.h:85,
from hw/usb/hcd-xhci.c:22:
/usr/include/bits/stdio2.h:70:10: note: '__builtin___snprintf_chk' output between 13 and 20 bytes into a destination of size 16
70 | return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
71 | __bos (__s), __fmt, __va_arg_pack ());
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210118181115.313742-1-philmd@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Device code shouldn't mess with QOM property "realized" since we have
proper interfaces (merge commit 6675a653). Commit 8ddab8dd3d
"usb/hcd-xhci: Split pci wrapper for xhci base model" and commit
f00ff136ee "usb: hcd-xhci-sysbus: Attach xhci to sysbus device"
reintroduced two instances. Clean them up. Note that s->xhci is
a (bus-less) TYPE_XHCI device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210119120151.53757-1-armbru@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201119025751.45750-1-alex.chen@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
USBDEVFS_GET_SPEED is used since version 5.2.0 and
202d69a715
resulting in the following build failure with kernel < 5.0:
../hw/usb/host-libusb.c: In function 'usb_host_open':
../hw/usb/host-libusb.c:953:32: error: 'USBDEVFS_GET_SPEED' undeclared (first use in this function); did you mean 'USBDEVFS_GETDRIVER'?
int rc = ioctl(hostfd, USBDEVFS_GET_SPEED, NULL);
^~~~~~~~~~~~~~~~~~
USBDEVFS_GETDRIVER
A tentative was made to fix this build failure with
4969e697c1
However, the assumption that distros with old kernels also have old
libusb is just wrong so also add a check for defined(USBDEVFS_GET_SPEED)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Message-id: 20201213213016.457350-1-fontaine.fabrice@gmail.com
[ kraxel: codestyle whitespace fixup ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
- headers update to Linux 5.11-rc2
- fix tcg emulation for some instructions that are generated by
clang Linux kernel builds
- vfio-ccw: wire up the device unplug notification mechanism
- fix a gcc 11 warning
-----BEGIN PGP SIGNATURE-----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=lCNW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck-gitlab/tags/s390x-20210121' into staging
s390x updates:
- headers update to Linux 5.11-rc2
- fix tcg emulation for some instructions that are generated by
clang Linux kernel builds
- vfio-ccw: wire up the device unplug notification mechanism
- fix a gcc 11 warning
# gpg: Signature made Thu 21 Jan 2021 12:08:12 GMT
# gpg: using RSA key C3D0D66DC3624FF6A8C018CEDECF6B93C6F02FAF
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck-gitlab/tags/s390x-20210121:
s390x: Use strpadcpy for copying vm name
vfio-ccw: Connect the device request notifier
Update linux headers to 5.11-rc2
update-linux-headers: Include const.h
s390x/tcg: Ignore register content if b1/b2 is zero when handling EXECUTE
tests/tcg/s390x: Fix EXRL tests
s390x/tcg: Don't ignore content in r0 when not specified via "b" or "x"
s390x/tcg: Fix RISBHG
s390x/tcg: Fix ALGSI
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The fid_list is currently open-coded. This doesn't seem to serve any
purpose that cannot be met with QEMU's generic lists. Let's go for a
QSIMPLEQ : this will allow to add new fids at the end of the list and
to improve the logic in v9fs_mark_fids_unreclaim().
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <20210118142300.801516-3-groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
This can only be 0 or 1.
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <20210118142300.801516-2-groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
This should always successfully write exactly two 32-bit integers.
Make it clear with an assert(), like v9fs_receive_status() and
v9fs_receive_response() already do when unmarshalling the same
header.
Fixes: Coverity CID 1438968
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <161035859647.1221144.4691749806675653934.stgit@bahia.lan>
Signed-off-by: Greg Kurz <groug@kaod.org>
- minor resource leak fixes in qemu-nbd
- ensure proper aio context when nbd server uses iothreads
- iotest refactorings in preparation for rewriting ./check to be more
flexible, and preparing for more nbd server reconnect features
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEccLMIrHEYCkn0vOqp6FrSiUnQ2oFAmAI5sMACgkQp6FrSiUn
Q2rmQwf+Jmlsn8s0tdeeOhv6mp8ZSyvr2/x1/daGHkzZqhoL7m/4kJLP4p/u8uTV
XzXyXt7MKvHKd8UvKB6VsN6z75RJvi7y8pKpOQA96t08hjWuAcVtivKnyZd6MTwj
zeKsmrE8LAuMjHvmsrtrmRqCSdaVeFPb3qC6bvJ+WEiXJIMiXybF7lccPvR7WWjR
2FcyraZJgnlKrQv1i8M1++Px5W14jhOacAMUNAdVzNiYpu4tq6PTk9giq1/GULCz
xVYGHqoTFYy7Slj7xKQJuOwGNLMwL+F9x7/6wRFhKxjutc0/Po1lSfbaNe8q147H
p9jtDT9/OuTlQf7qpqqyQnASABDgaA==
=XW+E
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ericb/tags/pull-nbd-2021-01-20' into staging
nbd patches for 2021-01-20
- minor resource leak fixes in qemu-nbd
- ensure proper aio context when nbd server uses iothreads
- iotest refactorings in preparation for rewriting ./check to be more
flexible, and preparing for more nbd server reconnect features
# gpg: Signature made Thu 21 Jan 2021 02:28:19 GMT
# gpg: using RSA key 71C2CC22B1C4602927D2F3AAA7A16B4A2527436A
# gpg: Good signature from "Eric Blake <eblake@redhat.com>" [full]
# gpg: aka "Eric Blake (Free Software Programmer) <ebb9@byu.net>" [full]
# gpg: aka "[jpeg image of size 6874]" [full]
# Primary key fingerprint: 71C2 CC22 B1C4 6029 27D2 F3AA A7A1 6B4A 2527 436A
* remotes/ericb/tags/pull-nbd-2021-01-20:
iotests.py: qemu_io(): reuse qemu_tool_pipe_and_status()
iotests.py: fix qemu_tool_pipe_and_status()
iotests/264: fix style
iotests: define group in each iotest
iotests/294: add shebang line
iotests: make tests executable
iotests: fix some whitespaces in test output files
iotests/303: use dot slash for qcow2.py running
iotests/277: use dot slash for nbd-fault-injector.py running
nbd/server: Quiesce coroutines on context switch
block: Honor blk_set_aio_context() context requirements
qemu-nbd: Fix a memleak in nbd_client_thread()
qemu-nbd: Fix a memleak in qemu_nbd_client_list()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the vfio-ccw code has a notifier interface to request that
a device be unplugged, let's wire that together.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20210104202057.48048-4-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The documentation for bdrv_set_aio_context_ignore() states this:
* The caller must own the AioContext lock for the old AioContext of bs, but it
* must not own the AioContext lock for new_context (unless new_context is the
* same as the current context of bs).
As blk_set_aio_context() makes use of this function, this rule also
applies to it.
Fix all occurrences where this rule wasn't honored.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20201214170519.223781-2-slp@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
As per POSIX specification of limits.h [1], OS libc may define
PAGE_SIZE in limits.h.
To prevent collosion of definition, we rename PAGE_SIZE here.
[1]: https://pubs.opengroup.org/onlinepubs/7908799/xsh/limits.h.html
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210118063808.12471-5-jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add the vmstate for the new NeXTPC devic; this is in theory
a migration compatibility break, but this machine doesn't have
working migration currently anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-11-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The fields scsi_irq, scsi_dma, scsi_reset and fd_irq in
NeXTState are all unused, except in commented out
"this should do something like this" code. Remove the
unused fields. As and when the functionality that might
use them is added, we can put in the correct kind of
wiring (which might or might not need to be a qemu_irq,
but which in any case will need to be in the NeXTPC
device, not in NeXTState).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-10-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Move the rtc into the NeXTPC struct. Since this is the last
use of the 'backdoor' NextState pointer we can now remove that.
Probably the RTC should be its own device at some point: in hardware
there is a separate MCS1850 RTC chip connected to the Peripheral
Controller via a 1-bit serial interface. That goes beyond the remit
of the current refactoring, though.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-9-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Make the next_irq function be GPIO inputs to the NEXT_PC
device, rather than a freestanding set of qemu_irq lines.
This fixes a minor Coverity issue where it correctly points
out the trivial memory leak of the memory allocated in the
call to qemu_allocate_irqs().
Fixes: CID 1421962
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-8-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
All the code which accesses int_status and int_mask is now doing
so via the NeXTPC->NeXTState indirection, so we can move these
fields into the NeXTPC struct where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-7-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Make the next_irq function take a NeXTPC* as its opaque rather than
the M68kCPU*. This will make it simpler to turn the next_irq
function into a gpio input line of the NeXTPC device in the next
commit.
For this to work we have to pass the CPU to the NeXTPC device via a
link property, in the same way we do in q800.c (and for the same
reason).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-6-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Move the registers handled by the scr_ops struct into the NeXTPC
device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-5-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Move the registers handled by the mmio_ops struct into the NeXTPC
device. This allows us to also move the scr1 and scr2 data fields.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-4-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Currently the next-cube board code open-codes a lot of handling of
interrupts and some miscellaneous registers. Move this into a proper
QOM device.
In the real hardware this functionality seems to be the
responsibility of the Peripheral Controller (PC) chip, so name the
device that.
There are several different things that will need to be moved into
this device:
* the mmio_iops register set
* the scr_ops register set
* the next_irq IRQ handling
To ease review, we structure the change as a sequence of commits: in
this first commit we create the skeleton of the NeXTPC device with no
content, but with a backdoor pointer to the NeXTState machine's state
struct so we can move parts of the code and still have refactored and
non-refactored code using the same struct data fields. Further
commits will move functionality into the new device piece by piece.
At the end we will be able to remove the backdoor pointer because all
the data fields will be in the NeXTPC struct and not the NeXTState
struct.
We'll add the VMState for the new device at the end of all that; this
is in theory a migration compatibility break but this machine does
not currently support migration at all anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-3-peter.maydell@linaro.org>
[huth: Add a comment in front of struct NeXTPC]
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The next_irq() function is global, but isn't actually used anywhere
outside next-cube.c. Make it static.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210115201206.17347-2-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Use g_autoptr() with Object and g_autofree with the string to
avoid the need of a cleanup path.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210114180628.1675603-6-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The function is called only inside spapr_hcall.c.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210114180628.1675603-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit 1e8b5b1aa1 ("spapr: Allow memory unplug to always succeed")
trying to unplug memory from a guest that doesn't support it (eg. rhel6)
no longer generates an error like it used to. Instead, it leaves the
memory around : only a subsequent reboot or manual use of drmgr within
the guest can complete the hot-unplug sequence. A flag was added to
SpaprMachineClass so that this new behavior only applies to the default
machine type.
We can do better. CAS processes all pending hot-unplug requests. This
means that we don't really care about what the guest supports if
the hot-unplug request happens before CAS.
All guests that we care for, even old ones, set enough bits in OV5
that lead to a non-empty bitmap in spapr->ov5_cas. Use that as a
heuristic to decide if CAS has already occured or not.
Always accept unplug requests that happen before CAS since CAS will
process them. Restore the previous behavior of rejecting them after
CAS when we know that the guest doesn't support memory hot-unplug.
This behavior is suitable for all machine types : this allows to
drop the pre_6_0_memory_unplug flag.
Fixes: 1e8b5b1aa1 ("spapr: Allow memory unplug to always succeed")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <161012708715.801107.11418801796987916516.stgit@bahia.lan>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Use the PCI_BUS type cast macro to convert result of qdev_get_child_bus().
Also remove the check for NULL afterwards which should not be needed
because sysbus_create_simple() uses error_abort and we create the PCI
host object here that's expected to have a PCI bus so this shouldn't
fail. Even if it would fail that would be due to a programmer error so
an error message is not necessary.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <a4dc55b56eed3ce899b7bf9835b980a114c52598.1610143658.git.balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This reverts commit e6d5106786 which was added mistakenly. While this
change works it was suggested during review that keeping dependencies
explicit for each board may be better than listing them in a common
option so keep the previous version and revert this change.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <8c65807fc7dc1c4c4f6320f2fd6409a3091c88ff.1610143658.git.balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This reverts commit 038da2adf that was mistakenly added, this
dependency is still needed to get libfdt dependencies even if fdt.o is
not needed by sam460ex.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15a9fa72eed4f02bdbeaef206803d5e22260e2de.1610143658.git.balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now we've converted all the callsites to directly create the QOM UIC
device themselves, the ppcuic_init() function is unused and can be
removed. The enum defining PPCUIC symbolic constants can be moved
to the ppc-uic.h header where it more naturally belongs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20210108171212.16500-5-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch the ppc405_uc boards to directly creating and configuring the
UIC, rather than doing it via the old ppcuic_init() helper function.
We retain the API feature of ppc405ep_init() where it passes back
something allowing the callers to wire up devices to the UIC if
they need to, even though neither of the callsites currently makes
use of this ability -- instead of passing back the qemu_irq array
we pass back the UIC DeviceState.
This fixes a trivial Coverity-detected memory leak where
we were leaking the array of IRQs returned by ppcuic_init().
Fixes: Coverity CID 1421922
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210108171212.16500-4-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In commit 34d0831f38 the ppc-uic device was added, with a dcr-base
property. The intention was that the default value of dcr-base should be
the one that most of our boards need, so that in the common case they
don't need to specify a property value.
All QEMU boards with a UIC use a dcr-base of 0xc0, with the exception of
sam460ex which has four UICs and so puts them at 0xc0, 0xd0, 0xe0, 0xf0.
So 0xc0 is the obvious right choice for the default dcr-base.
The board code conversions in commits 0270d74ef8 (bamboo) and
c5ac9dc64f (virtex_ml507) assumed that default was 0xc0. Unfortunately
the actual default in 34d0831f38 was 0x30, by mistake, so the
bamboo and virtex_ml507 boards were broken as they were converted
away from ppcuic_init() (which always specifies the dcr_base property
value explicitly).
Set the default dcr-base to 0xc0 as was intended, fixing bamboo and
virtex_ml507.
Fixes: 34d0831f38
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210111213007.7381-1-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The function ppc405cr_init() has apparently been unused since it was
added in commit 8ecc791352 in 2007.
Remove this dead code, so we don't have to convert it away from using
ppcuic_init().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210108171212.16500-3-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch the sam460ex board to directly creating and configuring the
UIC, rather than doing it via the old ppcuic_init() helper function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210108171212.16500-2-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- clean-ups to docker images
- drop duplicate jobs from shippable
- prettier tag generation (+gtags)
- generate browsable source tree
- more Travis->GitLab migrations
- fix checkpatch to deal with commits
- gate gdbstub tests on 8.3.1, expand tests
- support Xfer:auxv:read gdb packet
- better gdbstub cleanup
- use GDB's SVE register layout
- make arm-compat-semihosting common
- add riscv semihosting support
- add HEAPINFO, ELAPSED, TICKFREQ, TMPNAM and ISERROR to semihosting
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmAFXkcACgkQ+9DbCVqe
KkSP7Af/YNU4dWFf/N9CwvKQTSoJmBrO77HXccOJyYDS62hA8eoh83HWNll+xMV7
GxJDwQs0GS8J3oqcq1DktGgTUkCNxUfbHROjI2YXfRzoWnl0PFHY+Z/qRsq+bRhX
C3CiNCS/nM/NW2Q+H6TAD1MnXkia11+hqFhXrBRKVDON83MSvm0AspS5RO5eVpxo
TUTOD1YND+tAPWi5xAN+NyDuvfoY3tG4S4/DFUrHQfpS7uaHY/4qe8gMmJczveeo
uzJln9M7+pV5cgUWwr1fgCkbSyGgra+KX3GNoLIGS34C88cKRXAp7ZF19A3wQpiy
LXljmOinLfKuJqeRGwcnt6f8GrTn7A==
=XR0h
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-misc-180121-2' into staging
Testing, gdbstub and semihosting patches:
- clean-ups to docker images
- drop duplicate jobs from shippable
- prettier tag generation (+gtags)
- generate browsable source tree
- more Travis->GitLab migrations
- fix checkpatch to deal with commits
- gate gdbstub tests on 8.3.1, expand tests
- support Xfer:auxv:read gdb packet
- better gdbstub cleanup
- use GDB's SVE register layout
- make arm-compat-semihosting common
- add riscv semihosting support
- add HEAPINFO, ELAPSED, TICKFREQ, TMPNAM and ISERROR to semihosting
# gpg: Signature made Mon 18 Jan 2021 10:09:11 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-misc-180121-2: (30 commits)
semihosting: Implement SYS_ISERROR
semihosting: Implement SYS_TMPNAM
semihosting: Implement SYS_ELAPSED and SYS_TICKFREQ
riscv: Add semihosting support for user mode
riscv: Add semihosting support
semihosting: Support SYS_HEAPINFO when env->boot_info is not set
semihosting: Change internal common-semi interfaces to use CPUState *
semihosting: Change common-semi API to be architecture-independent
semihosting: Move ARM semihosting code to shared directories
target/arm: use official org.gnu.gdb.aarch64.sve layout for registers
gdbstub: ensure we clean-up when terminated
gdbstub: drop gdbserver_cleanup in favour of gdb_exit
gdbstub: drop CPUEnv from gdb_exit()
gdbstub: add support to Xfer:auxv:read: packet
gdbstub: implement a softmmu based test
Revert "tests/tcg/multiarch/Makefile.target: Disable run-gdbstub-sha1 test"
configure: gate our use of GDB to 8.3.1 or above
test/guest-debug: echo QEMU command as well
scripts/checkpatch.pl: fix git-show invocation to include diffstat
gitlab: migrate the minimal tools and unit tests from Travis
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# default-configs/targets/riscv32-linux-user.mak
# default-configs/targets/riscv64-linux-user.mak
When running device-introspect-test, a memory leak occurred in the mos6522_init
function, this patch use timer_free() in the finalize function to fix it.
ASAN shows memory leak stack:
Direct leak of 96 byte(s) in 2 object(s) allocated from:
#0 0xfffd5fe9e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xfffd5f7b6800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaae50303d0c in timer_new_full qemu/include/qemu/timer.h:523
#3 0xaaae50303d0c in timer_new qemu/include/qemu/timer.h:544
#4 0xaaae50303d0c in timer_new_ns qemu/include/qemu/timer.h:562
#5 0xaaae50303d0c in mos6522_init qemu/hw/misc/mos6522.c:490
#6 0xaaae50b77d70 in object_init_with_type qemu/qom/object.c:371
#7 0xaaae50b7ae84 in object_initialize_with_type qemu/qom/object.c:515
#8 0xaaae50b7b0f8 in object_new_with_type qemu/qom/object.c:729
#9 0xaaae50bb6d58 in qmp_device_list_properties qemu/qom/qom-qmp-cmds.c:153
#10 0xaaae50d7e1dc in qmp_marshal_device_list_properties qemu/qapi/qapi-commands-qdev.c:59
#11 0xaaae50dc87a0 in do_qmp_dispatch_bh qemu/qapi/qmp-dispatch.c:110
#12 0xaaae50d931a0 in aio_bh_call qemu/util/async.c:136
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210112112705.380534-3-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When running device-introspect-test, a memory leak occurred in the pl031_init
function, this patch use timer_free() in the finalize function to fix it.
ASAN shows memory leak stack:
Direct leak of 48 byte(s) in 1 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf5621cfc in timer_new_full qemu/include/qemu/timer.h:523
#3 0xaaabf5621cfc in timer_new qemu/include/qemu/timer.h:544
#4 0xaaabf5621cfc in timer_new_ns qemu/include/qemu/timer.h:562
#5 0xaaabf5621cfc in pl031_init qemu/hw/rtc/pl031.c:194
#6 0xaaabf6339f6c in object_initialize_with_type qemu/qom/object.c:515
#7 0xaaabf633a1e0 in object_new_with_type qemu/qom/object.c:729
#8 0xaaabf6375e40 in qmp_device_list_properties qemu/qom/qom-qmp-cmds.c:153
#9 0xaaabf5a95540 in qdev_device_help qemu/softmmu/qdev-monitor.c:283
#10 0xaaabf5a96940 in qmp_device_add qemu/softmmu/qdev-monitor.c:801
#11 0xaaabf5a96e70 in hmp_device_add qemu/softmmu/qdev-monitor.c:916
#12 0xaaabf5ac0a2c in handle_hmp_command qemu/monitor/hmp.c:1100
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210112112705.380534-2-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This PR:
- Fixes some issues with the m25p80
- Improves GDB support for RISC-V
- Fixes some Linux boot issues, specifiaclly 32-bit boot failures
- Enforces PMP exceptions correctly
- Fixes some Coverity issues
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmAEsc8ACgkQIeENKd+X
cFT3cwf+NNPVzjl0T7OEI1XxL6UCEkX6/cgxPv+ChjMCRlfnts9iHMWyeiO8E4mG
qORpLe5YCT+tAVA+rKKVu8ADp5pE9sdRp8gO7TMhZaHi3r1CQpsleZWE9R0IoBIu
eiENTgFHIV3VFcJQpOgorqCJ9qRnx2pPjjwf0H8G/hMYcgaMAzz+rdK+XvP0cCaY
/U78g0pPWx1MwdIFhhhaxAhbthnv6TkWf6oSPeGezDaAp1tnNg/Bd+FL6pT0vAM9
Mhr39TqrOJ/R0npsTngVe5Rl23Gqh3/1AYOnZz1+e9J0pB4YXnxwwiuV0t8lZnsw
OFIGXm7V3dL8BQ4ycZojlIkmML2Siw==
=3q/k
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210117-3' into staging
First RISC-V PR for 6.0
This PR:
- Fixes some issues with the m25p80
- Improves GDB support for RISC-V
- Fixes some Linux boot issues, specifiaclly 32-bit boot failures
- Enforces PMP exceptions correctly
- Fixes some Coverity issues
# gpg: Signature made Sun 17 Jan 2021 21:53:19 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210117-3:
riscv: Pass RISCVHartArrayState by pointer
target/riscv: Remove built-in GDB XML files for CSRs
target/riscv: Generate the GDB XML file for CSR registers dynamically
target/riscv: Add CSR name in the CSR function table
target/riscv: Make csr_ops[CSR_TABLE_SIZE] external
hw/misc/sifive_u_otp: handling the fails of blk_pread and blk_pwrite
hw/riscv: sifive_u: Use SIFIVE_U_CPU for mc->default_cpu_type
target/riscv/pmp: Raise exception if no PMP entry is configured
RISC-V: Place DTB at 3GB boundary instead of 4GB
gdb: riscv: Add target description
hw/block: m25p80: Implement AAI-WP command support for SST flashes
hw/block: m25p80: Don't write to flash if write is disabled
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Part of Semihosting for AArch32 and AArch64 Release 2.0
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210107170717.2098982-10-keithp@keithp.com>
Message-Id: <20210108224256.2321-21-alex.bennee@linaro.org>
Part of Semihosting for AArch32 and AArch64 Release 2.0
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210107170717.2098982-9-keithp@keithp.com>
Message-Id: <20210108224256.2321-20-alex.bennee@linaro.org>
These are part of Semihosting for AArch32 and AArch64 Release 2.0
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210107170717.2098982-8-keithp@keithp.com>
Message-Id: <20210108224256.2321-19-alex.bennee@linaro.org>
Adapt the arm semihosting support code for RISCV. This implementation
is based on the standard for RISC-V semihosting version 0.2 as
documented in
https://github.com/riscv/riscv-semihosting-spec/releases/tag/0.2
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210107170717.2098982-6-keithp@keithp.com>
Message-Id: <20210108224256.2321-17-alex.bennee@linaro.org>
env->boot_info is only set in some ARM startup paths, so we cannot
rely on it to support the SYS_HEAPINFO semihosting function. When not
available, fallback to finding a RAM memory region containing the
current stack and use the base of that.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210107170717.2098982-5-keithp@keithp.com>
Message-Id: <20210108224256.2321-16-alex.bennee@linaro.org>
This makes all of the internal interfaces architecture-independent and
renames the internal functions to use the 'common_semi' prefix instead
of 'arm' or 'arm_semi'.
To do this, some new architecture-specific internal helper functions
were created:
static inline target_ulong
common_semi_arg(CPUState *cs, int argno)
Returns the argno'th semihosting argument, where argno can be
either 0 or 1.
static inline void
common_semi_set_ret(CPUState *cs, target_ulong ret)
Sets the semihosting return value.
static inline bool
common_semi_sys_exit_extended(CPUState *cs, int nr)
This detects whether the specified semihosting call, which
is either TARGET_SYS_EXIT or TARGET_SYS_EXIT_EXTENDED should
be executed using the TARGET_SYS_EXIT_EXTENDED semantics.
static inline target_ulong
common_semi_rambase(CPUState *cs)
Returns the base of RAM region used for heap and stack. This
is used to construct plausible values for the SYS_HEAPINFO
call.
In addition, several existing functions have been changed to flag
areas of code which are architecture specific:
static target_ulong
common_semi_flen_buf(CPUState *cs)
Returns the current stack pointer minus 64, which is
where a stat structure will be placed on the stack
#define GET_ARG(n)
This fetches arguments from the semihosting command's argument
block. The address of this is available implicitly through the
local 'args' variable. This is *mostly* architecture
independent, but does depend on the current ABI's notion of
the size of a 'long' parameter, which may need run-time checks
(as it does on AARCH64)
#define SET_ARG(n, val)
This mirrors GET_ARG and stores data back into the argument
block.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210107170717.2098982-4-keithp@keithp.com>
Message-Id: <20210108224256.2321-15-alex.bennee@linaro.org>
The public API is now defined in
hw/semihosting/common-semi.h. do_common_semihosting takes CPUState *
instead of CPUARMState *. All internal functions have been renamed
common_semi_ instead of arm_semi_ or arm_. Aside from the API change,
there are no functional changes in this patch.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210107170717.2098982-3-keithp@keithp.com>
Message-Id: <20210108224256.2321-14-alex.bennee@linaro.org>
This commit renames two files which provide ARM semihosting support so
that they can be shared by other architectures:
1. target/arm/arm-semi.c -> hw/semihosting/common-semi.c
2. linux-user/arm/semihost.c -> linux-user/semihost.c
The build system was modified use a new config variable,
CONFIG_ARM_COMPATIBLE_SEMIHOSTING, which has been added to the ARM
softmmu and linux-user default configs. The contents of the source
files has not been changed in this patch.
Signed-off-by: Keith Packard <keithp@keithp.com>
[AJB: rename arm-compat-semi, select SEMIHOSTING]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210107170717.2098982-2-keithp@keithp.com>
Message-Id: <20210108224256.2321-13-alex.bennee@linaro.org>
PXB is now supported on ARM, so let's compile for arm_virt machine.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20210114100643.10617-7-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Exclude the resources of extra root bridges from PCI0's _CRS. Otherwise,
the resource windows would overlap in guest, and the IO resource window
would fail to be registered.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20210114100643.10617-6-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There may be some differences in pci resource assignment between guest os
and firmware.
Eg. A Bridge with Bus [d2]
-+-[0000:d2]---01.0-[d3]----01.0
where [d2:01.00] is a pcie-pci-bridge with BAR0 (mem, 64-bit, non-pref) [size=256]
[d3:01.00] is a PCI Device with BAR0 (mem, 64-bit, pref) [size=128K]
BAR4 (mem, 64-bit, pref) [size=64M]
In EDK2, the Resource Map would be:
PciBus: Resource Map for Bridge [D2|01|00]
Type = PMem64; Base = 0x8004000000; Length = 0x4100000; Alignment = 0x3FFFFFF
Base = 0x8004000000; Length = 0x4000000; Alignment = 0x3FFFFFF; Owner = PCI [D3|01|00:20]
Base = 0x8008000000; Length = 0x20000; Alignment = 0x1FFFF; Owner = PCI [D3|01|00:10]
Type = Mem64; Base = 0x8008100000; Length = 0x100; Alignment = 0xFFF
It would use 0x4100000 to calculate the root bus's PMem64 resource window.
While in Linux, kernel will use 0x1FFFFFF as the alignment to calculate
the PMem64 size, which would be 0x6000000. So kernel would try to
allocate 0x6000000 from the PMem64 resource window, but since the window
size is 0x4100000 as assigned by EDK2, the allocation would fail.
The diffences could result in resource assignment failure.
Using _DSM #5 method to inform guest os not to ignore the PCI configuration
that firmware has done at boot time could handle the differences.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20210114100643.10617-5-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
AML needs Address Translation offset to describe how a bridge translates
addresses accross the bridge when using an address descriptor, and
especially on ARM, the translation offset of pio resource is usually
non zero.
Therefore, it's necessary to pass offset for pio, mmio32, mmio64 and bus
number into build_crs.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20210114100643.10617-4-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We were accidently passing RISCVHartArrayState by value instead of
pointer. The type is 824 bytes long so let's correct that and pass it by
pointer instead.
Fixes: Coverity CID 1438099
Fixes: Coverity CID 1438100
Fixes: Coverity CID 1438101
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Message-id: f3e04424723e0e222769991896cc82308fd23f76.1610751609.git.alistair.francis@wdc.com
Fix code coverage issues by checking return value and handling fail case
of blk_pread() and blk_pwrite(). Return default value 0xff if read fails.
Fixes: Coverity CID 1435959
Fixes: Coverity CID 1435960
Fixes: Coverity CID 1435961
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201104092900.21214-1-green.wan@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SIFIVE_U_CPU is conditionally set to SIFIVE_U34 or SIFIVE_U54, hence
there is no need to use #idef to set the mc->default_cpu_type.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210109143637.29645-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we place the DTB at 2MB from 4GB or end of DRAM which ever is
lesser. However, Linux kernel can address only 1GB of memory for RV32.
Thus, it can not map anything beyond 3GB (assuming 2GB is the starting address).
As a result, it can not process DT and panic if opensbi dynamic firmware
is used. While at it, place the DTB further away to avoid in memory placement
issues in future.
Fix this by placing the DTB at 16MB from 3GB or end of DRAM whichever is lower.
Fixes: 66b1205bc5 ("RISC-V: Copy the fdt in dram instead of ROM")
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Message-id: 20210107091127.3407870-1-atish.patra@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Auto Address Increment (AAI) Word-Program is a special command of
SST flashes. AAI-WP allows multiple bytes of data to be programmed
without re-issuing the next sequential address location.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 1608688825-81519-2-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When write is disabled, the write to flash should be avoided
in flash_write8().
Fixes: 82a2499011 ("m25p80: Initial implementation of SPI flash device")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 1608688825-81519-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Depending on the client activity, the server can be asked to open a huge
number of file descriptors and eventually hit RLIMIT_NOFILE. This is
currently mitigated using a reclaim logic : the server closes the file
descriptors of idle fids, based on the assumption that it will be able
to re-open them later. This assumption doesn't hold of course if the
client requests the file to be unlinked. In this case, we loop on the
entire fid list and mark all related fids as unreclaimable (the reclaim
logic will just ignore them) and, of course, we open or re-open their
file descriptors if needed since we're about to unlink the file.
This is the purpose of v9fs_mark_fids_unreclaim(). Since the actual
opening of a file can cause the coroutine to yield, another client
request could possibly add a new fid that we may want to mark as
non-reclaimable as well. The loop is thus restarted if the re-open
request was actually transmitted to the backend. This is achieved
by keeping a reference on the first fid (head) before traversing
the list.
This is wrong in several ways:
- a potential clunk request from the client could tear the first
fid down and cause the reference to be stale. This leads to a
use-after-free error that can be detected with ASAN, using a
custom 9p client
- fids are added at the head of the list : restarting from the
previous head will always miss fids added by a some other
potential request
All these problems could be avoided if fids were being added at the
end of the list. This can be achieved with a QSIMPLEQ, but this is
probably too much change for a bug fix. For now let's keep it
simple and just restart the loop from the current head.
Fixes: CVE-2021-20181
Buglink: https://bugs.launchpad.net/qemu/+bug/1911666
Reported-by: Zero Day Initiative <zdi-disclosures@trendmicro.com>
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <161064025265.1838153.15185571283519390907.stgit@bahia.lan>
Signed-off-by: Greg Kurz <groug@kaod.org>
The 'fulong2e' machine alias has been marked as deprecated since
QEMU v5.1 (commit c3a09ff68d, the machine is renamed 'fuloong2e').
Time to remove it now.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20210106184602.3771551-1-f4bug@amsat.org>
Directly check if the CPU supports 64-bit with the recently
added cpu_type_is_64bit() helper (inlined).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210104221154.3127610-6-f4bug@amsat.org>
virtio-fs qualifies as a bootable device minimally under OVMF, but
currently the necessary "bootindex" property is missing. Add the property.
Expose the property only in the PCI device, for now. There is no boot
support for virtiofs on s390x (ccw) for the time being [1] [2], so leave
the CCW device unchanged. Add the property to the base device still,
because adding the alias to the CCW device later will be easier this way
[3].
[1] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01745.html
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01870.html
[3] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg01751.html
Example OpenFirmware device path for the "vhost-user-fs-pci" device in the
"bootorder" fw_cfg file:
/pci@i0cf8/pci-bridge@1,6/pci1af4,105a@0/filesystem@0
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ján Tomko <jtomko@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: virtio-fs@redhat.com
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210112131603.12686-1-lersek@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the slot is in steady powered-off state and the device is being
removed, there's no need to press the attention button. Nor is it
mandated by the Standard Hot-Plug Controller Specification, Rev. 1.0.
Moreover it confuses the guest, Linux in particular, as it assumes that
the attention button pressed in this state indicates that the device has
been inserted and will need to be powered on. Therefore it transitions
the slot into BLINKING_ON state for 5 seconds, and discovers at the end
that no device is actually inserted:
... unplug request
[12685.451329] shpchp 0000:01:00.0: Button pressed on Slot(2)
[12685.455478] shpchp 0000:01:00.0: PCI slot #2 - powering off due to button press
... in 5 seconds OS powers off the slot, QEMU ejects the device
[12690.632282] shpchp 0000:01:00.0: Latch open on Slot(2)
... excessive button press in steady powered-off state
[12690.634267] shpchp 0000:01:00.0: Button pressed on Slot(2)
[12690.636256] shpchp 0000:01:00.0: Card not present on Slot(2)
... the last button press spawns powering on the slot
[12690.638909] shpchp 0000:01:00.0: PCI slot #2 - powering on due to button press
... in 5 more seconds attempt to power on discovers empty slot
[12695.735986] shpchp 0000:01:00.0: No adapter on slot(2)
Worse, if the real device insertion happens within 5 seconds from the
apparent completion of the previous device removal (signaled via
DEVICE_DELETED event), the new button press will be interpreted as the
cancellation of that misguided powering on:
[13448.965295] shpchp 0000:01:00.0: Button pressed on Slot(2)
[13448.969430] shpchp 0000:01:00.0: PCI slot #2 - powering off due to button press
[13454.025107] shpchp 0000:01:00.0: Latch open on Slot(2)
[13454.027101] shpchp 0000:01:00.0: Button pressed on Slot(2)
[13454.029165] shpchp 0000:01:00.0: Card not present on Slot(2)
... the excessive button press spawns powering on the slot
... device has already been ejected by QEMU
[13454.031949] shpchp 0000:01:00.0: PCI slot #2 - powering on due to button press
... new device is inserted in the slot
[13456.861545] shpchp 0000:01:00.0: Latch close on Slot(2)
... valid button press arrives before 5 s since the wrong one
[13456.864894] shpchp 0000:01:00.0: Button pressed on Slot(2)
[13456.869211] shpchp 0000:01:00.0: Card present on Slot(2)
... the valid button press is counted as cancellation of the wrong one
[13456.873173] shpchp 0000:01:00.0: Button cancel on Slot(2)
[13456.877101] shpchp 0000:01:00.0: PCI slot #2 - action canceled due to button press
As a result, the newly inserted device isn't brought up by the guest.
Avoid this situation by not pushing the attention button when the device
in the slot is in powered-off state and is being ejected.
FWIW pcie implementation doesn't suffer from this problem.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20201102053750.2281818-1-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that all of the object property links to the heathrow PIC and OpenPIC have
been removed from the macio devices, it is safe to allow the macio-oldworld
and macio-neworld devices to be marked as user_creatable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201229175619.6051-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This both allows the wiring to be done as Ben suggested in his original comment in
gpio.c and also enables the OpenPIC object property link to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201229175619.6051-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The OpenPIC device is located within the macio device on real hardware so make it
a child of the macio-newworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-newworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In order to move the OpenPIC device to the macio device, the PCI bus needs to be
initialised before the macio device and also before wiring the OpenPIC IRQs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The heathrow PIC is located within the macio device on real hardware so make it
a child of the macio-oldworld device. This also removes the need for setting and
checking a separate PIC object property link on the macio-oldworld device which
currently causes the automated QOM introspection tests to fail.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In order to move the heathrow PIC to the macio device, the PCI bus needs to be
initialised before the macio device and also before wiring the PIC IRQs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This condition will have already been caught when wiring the heathrow PIC
IRQs to the CPU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201229175619.6051-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
A device shouldn't access its parent object which is QOM internal.
Instead it should use type cast for this purporse. This patch fixes this
issue for all NPCM7XX Devices.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210108190945.949196-7-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PWM module is part of NPCM7XX module. Each NPCM7XX module has two
identical PWM modules. Each module contains 4 PWM entries. Each PWM has
two outputs: frequency and duty_cycle. Both are computed using inputs
from software side.
This module does not model detail pulse signals since it is expensive.
It also does not model interrupts and watchdogs that are dependant on
the detail models. The interfaces for these are left in the module so
that anyone in need for these functionalities can implement on their
own.
The user can read the duty cycle and frequency using qom-get command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-5-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ADC is part of NPCM7XX Module. Its behavior is controled by the
ADC_CON register. It converts one of the eight analog inputs into a
digital input and stores it in the ADC_DATA register when enabled.
Users can alter input value by using qom-set QMP command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-4-wuhaotsh@google.com
[PMM: Added missing hw/adc/trace.h file]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch makes NPCM7XX Timer to use a the timer clock generated by the
CLK module instead of the magic number TIMER_REF_HZ.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows NPCM7XX CLK module to compute clocks that are used by
other NPCM7XX modules.
Add a new struct NPCM7xxClockConverterState which represents a
single converter. Each clock converter in CLK module represents one
converter in NPCM7XX CLK Module(PLL, SEL or Divider). Each converter
takes one or more input clocks and converts them into one output clock.
They form a clock hierarchy in the CLK module and are responsible for
outputing clocks for various other modules in an NPCM7XX SoC.
Each converter has a function pointer called "convert" which represents
the unique logic for that converter.
The clock contains two initialization information: ConverterInitInfo and
ConverterConnectionInfo. They represent the vertices and edges in the
clock diagram respectively.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210108190945.949196-2-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The lan9118 code mostly uses symbolic constants for register offsets;
the exceptions are those which the datasheet doesn't give an official
symbolic name to.
Add some names for the registers which don't already have them, based
on the longer names they are given in the memory map.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210108180401.2263-3-peter.maydell@linaro.org
Add trace events for virtio command and response tracing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-2-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At present, when booting U-Boot on QEMU sabrelite, we see:
Net: Board Net Initialization Failed
No ethernet found.
U-Boot scans PHY at address 4/5/6/7 (see board_eth_init() in the
U-Boot source: board/boundary/nitrogen6x/nitrogen6x.c). On the real
board, the Ethernet PHY is at address 6. Adjust this by updating the
"fec-phy-num" property of the fsl_imx6 SoC object.
With this change, U-Boot sees the PHY but complains MAC address:
Net: using phy at 6
FEC [PRIME]
Error: FEC address not set.
This is due to U-Boot tries to read the MAC address from the fuse,
which QEMU does not have any valid content filled in. However this
does not prevent the Ethernet from working in QEMU. We just need to
set up the MAC address later in the U-Boot command shell, by:
=> setenv ethaddr 00:11:22:33:44:55
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210106063504.10841-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently when U-Boot boots, it prints "??" for i.MX processor:
CPU: Freescale i.MX?? rev1.0 at 792 MHz
The register that was used to determine the silicon type is
undocumented in the latest IMX6DQRM (Rev. 6, 05/2020), but we
can refer to get_cpu_rev() in arch/arm/mach-imx/mx6/soc.c in
the U-Boot source codes that USB_ANALOG_DIGPROG is used.
Update its reset value to indicate i.MX6Q.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210106063504.10841-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
U-Boot expects PMU_MISC0 register bit 7 is set (see init_bandgap()
in arch/arm/mach-imx/mx6/soc.c) during boot. This bit indicates the
bandgap has stabilized.
With this change, the latest upstream U-Boot (v2021.01-rc3) for imx6
sabrelite board (mx6qsabrelite_defconfig), with a slight change made
by switching CONFIG_OF_SEPARATE to CONFIG_OF_EMBED, boots to U-Boot
shell on QEMU with the following command:
$ qemu-system-arm -M sabrelite -smp 4 -m 1G -kernel u-boot \
-display none -serial null -serial stdio
Boot log below:
U-Boot 2021.01-rc3 (Dec 12 2020 - 17:40:02 +0800)
CPU: Freescale i.MX?? rev1.0 at 792 MHz
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Lite Board
Board: SABRE Lite
I2C: ready
DRAM: 1 GiB
force_idle_bus: sda=0 scl=0 sda.gp=0x5c scl.gp=0x55
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0x6d scl.gp=0x6c
force_idle_bus: failed to clear bus, sda=0 scl=0
force_idle_bus: sda=0 scl=0 sda.gp=0xcb scl.gp=0x5
force_idle_bus: failed to clear bus, sda=0 scl=0
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - No block device, using default environment
In: serial
Out: serial
Err: serial
Net: Board Net Initialization Failed
No ethernet found.
starting USB...
Bus usb@2184000: usb dr_mode not found
USB EHCI 1.00
Bus usb@2184200: USB EHCI 1.00
scanning bus usb@2184000 for devices... 1 USB Device(s) found
scanning bus usb@2184200 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit any key to stop autoboot: 0
=>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210106063504.10841-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the
exynos4210_mct_init function, so use ptimer_free() in the finalize function to
avoid it.
ASAN shows memory leak stack:
Indirect leak of 96 byte(s) in 1 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db78 in ptimer_init /qemu/hw/core/ptimer.c:432
#3 0xaaabf56b01a0 in exynos4210_mct_init /qemu/hw/timer/exynos4210_mct.c:1505
#4 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#5 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
#6 0xaaabf6375e40 in qmp_device_list_properties /qemu/qom/qom-qmp-cmds.c:153
#7 0xaaabf653d8ec in qmp_marshal_device_list_properties /qemu/qapi/qapi-commands-qdev.c:59
#8 0xaaabf6587d08 in do_qmp_dispatch_bh /qemu/qapi/qmp-dispatch.c:110
#9 0xaaabf6552708 in aio_bh_call /qemu/util/async.c:136
#10 0xaaabf6552708 in aio_bh_poll /qemu/util/async.c:164
#11 0xaaabf655f19c in aio_dispatch /qemu/util/aio-posix.c:381
#12 0xaaabf65523f4 in aio_ctx_dispatch /qemu/util/async.c:306
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the
mv88w8618_pit_init function, so use ptimer_free() in the finalize function to
avoid it.
ASAN shows memory leak stack:
Indirect leak of 192 byte(s) in 4 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db84 in timer_new_full /qemu/include/qemu/timer.h:523
#3 0xaaabf555db84 in timer_new /qemu/include/qemu/timer.h:544
#4 0xaaabf555db84 in timer_new_ns /qemu/include/qemu/timer.h:562
#5 0xaaabf555db84 in ptimer_init /qemu/hw/core/ptimer.c:433
#6 0xaaabf5bb2290 in mv88w8618_timer_init /qemu/hw/arm/musicpal.c:862
#7 0xaaabf5bb2290 in mv88w8618_pit_init /qemu/hw/arm/musicpal.c:954
#8 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#9 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
#10 0xaaabf6375e40 in qmp_device_list_properties /qemu/qom/qom-qmp-cmds.c:153
#11 0xaaabf5a95540 in qdev_device_help /qemu/softmmu/qdev-monitor.c:283
#12 0xaaabf5a96940 in qmp_device_add /qemu/softmmu/qdev-monitor.c:801
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the
mss_timer_init function, so use ptimer_free() in the finalize function to avoid
it.
ASAN shows memory leak stack:
Indirect leak of 192 byte(s) in 2 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db78 in ptimer_init /qemu/hw/core/ptimer.c:432
#3 0xaaabf58a0010 in mss_timer_init /qemu/hw/timer/mss-timer.c:235
#4 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#5 0xaaabf633ca04 in object_initialize_child_with_propsv /qemu/qom/object.c:564
#6 0xaaabf633cc08 in object_initialize_child_with_props /qemu/qom/object.c:547
#7 0xaaabf5b8316c in m2sxxx_soc_initfn /qemu/hw/arm/msf2-soc.c:70
#8 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#9 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
#10 0xaaabf6375e40 in qmp_device_list_properties /qemu/qom/qom-qmp-cmds.c:153
#11 0xaaabf653d8ec in qmp_marshal_device_list_properties /qemu/qapi/qapi-commands-qdev.c:59
#12 0xaaabf6587d08 in do_qmp_dispatch_bh /qemu/qapi/qmp-dispatch.c:110
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the
exynos4210_pwm_init function, so use ptimer_free() in the finalize function to
avoid it.
ASAN shows memory leak stack:
Indirect leak of 240 byte(s) in 5 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db84 in timer_new_full /qemu/include/qemu/timer.h:523
#3 0xaaabf555db84 in timer_new /qemu/include/qemu/timer.h:544
#4 0xaaabf555db84 in timer_new_ns /qemu/include/qemu/timer.h:562
#5 0xaaabf555db84 in ptimer_init /qemu/hw/core/ptimer.c:433
#6 0xaaabf56a36cc in exynos4210_pwm_init /qemu/hw/timer/exynos4210_pwm.c:401
#7 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#8 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
#9 0xaaabf6375e40 in qmp_device_list_properties /qemu/qom/qom-qmp-cmds.c:153
#10 0xaaabf653d8ec in qmp_marshal_device_list_properties /qemu/qapi/qapi-commands-qdev.c:59
#11 0xaaabf6587d08 in do_qmp_dispatch_bh /qemu/qapi/qmp-dispatch.c:110
#12 0xaaabf6552708 in aio_bh_call /qemu/util/async.c:136
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the
exynos4210_rtc_init function, so use ptimer_free() in the finalize function to
avoid it.
ASAN shows memory leak stack:
Indirect leak of 96 byte(s) in 1 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db78 in ptimer_init /qemu/hw/core/ptimer.c:432
#3 0xaaabf57b3934 in exynos4210_rtc_init /qemu/hw/rtc/exynos4210_rtc.c:567
#4 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#5 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
#6 0xaaabf6375e40 in qmp_device_list_properties /qemu/qom/qom-qmp-cmds.c:153
#7 0xaaabf653d8ec in qmp_marshal_device_list_properties /qemu/qapi/qapi-commands-qdev.c:59
#8 0xaaabf6587d08 in do_qmp_dispatch_bh /qemu/qapi/qmp-dispatch.c:110
#9 0xaaabf6552708 in aio_bh_call /qemu/util/async.c:136
#10 0xaaabf6552708 in aio_bh_poll /qemu/util/async.c:164
#11 0xaaabf655f19c in aio_dispatch /qemu/util/aio-posix.c:381
#12 0xaaabf65523f4 in aio_ctx_dispatch /qemu/util/async.c:306
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the a10_pit_init
function, so use ptimer_free() in the finalize function to avoid it.
ASAN shows memory leak stack:
Indirect leak of 288 byte(s) in 6 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db84 in timer_new_full /qemu/include/qemu/timer.h:523
#3 0xaaabf555db84 in timer_new /qemu/include/qemu/timer.h:544
#4 0xaaabf555db84 in timer_new_ns /qemu/include/qemu/timer.h:562
#5 0xaaabf555db84 in ptimer_init /qemu/hw/core/ptimer.c:433
#6 0xaaabf57415e8 in a10_pit_init /qemu/hw/timer/allwinner-a10-pit.c:278
#7 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#8 0xaaabf633ca04 in object_initialize_child_with_propsv /qemu/qom/object.c:564
#9 0xaaabf633cc08 in object_initialize_child_with_props /qemu/qom/object.c:547
#10 0xaaabf5b94680 in aw_a10_init /qemu/hw/arm/allwinner-a10.c:49
#11 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#12 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the
digic_timer_init function, so use ptimer_free() in the finalize function to
avoid it.
ASAN shows memory leak stack:
Indirect leak of 288 byte(s) in 3 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db78 in ptimer_init /qemu/hw/core/ptimer.c:432
#3 0xaaabf5b04084 in digic_timer_init /qemu/hw/timer/digic-timer.c:142
#4 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#5 0xaaabf633ca04 in object_initialize_child_with_propsv /qemu/qom/object.c:564
#6 0xaaabf633cc08 in object_initialize_child_with_props /qemu/qom/object.c:547
#7 0xaaabf5b40e84 in digic_init /qemu/hw/arm/digic.c:46
#8 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#9 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
#10 0xaaabf6375e40 in qmp_device_list_properties /qemu/qom/qom-qmp-cmds.c:153
#11 0xaaabf653d8ec in qmp_marshal_device_list_properties /qemu/qapi/qapi-commands-qdev.c:59
#12 0xaaabf6587d08 in do_qmp_dispatch_bh /qemu/qapi/qmp-dispatch.c:110
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
Support for running KVM on 32-bit Arm hosts was removed in commit
82bf7ae84c. You can still run a 32-bit guest on a 64-bit Arm
host CPU, but because Arm KVM requires the host and guest CPU types
to match, it is not possible to run a guest that requires a Cortex-A9
or Cortex-A15 CPU there. That means that the code in the
highbank/midway board models to support KVM is no longer used, and we
can delete it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201215144215.28482-1-peter.maydell@linaro.org
The CCR is a register most of whose bits are banked between security
states but where BFHFNMIGN is not, and we keep it in the non-secure
entry of the v7m.ccr[] array. The logic which tries to handle this
bit fails to implement the "RAZ/WI from Nonsecure if AIRCR.BFHFNMINS
is zero" requirement; correct the omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201210201433.26262-2-peter.maydell@linaro.org
virt machine's 'smp_cpus' and machine->smp.cpus must always have the
same value. And, anywhere we have virt machine state we have machine
state. So let's remove the redundancy. Also, to make it easier to see
that machine->smp is the true source for "smp_cpus" and "max_cpus",
avoid passing them in function parameters, preferring instead to get
them from the state.
No functional change intended.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Ying Fang <fangying1@huawei.com>
Message-id: 20201215174815.51520-1-drjones@redhat.com
[PMM: minor formatting tweak to smp_cpus variable declaration]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct the indexing into s->cpu_ctlr for vCPUs.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20201214222154.3480243-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sun4m board code connects both of the IRQ outputs of each ESCC to the
same slavio input qemu_irq. Connecting two qemu_irqs outputs directly to the
same input is not valid as it produces subtly wrong behaviour (for instance
if both the IRQ lines are high, and then one goes low, the PIC input will see
this as a high-to-low transition even though the second IRQ line should still
be holding it high).
This kind of wiring needs an explicitly created OR gate; add one.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201219111934.5540-1-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently the GRLIB_IRQMP device is used in one place (the leon3 board),
but instead of the device providing inbound gpio lines for the board
to wire up, the board code itself calls qemu_allocate_irqs() with
the handler function being a set_irq function defined in the code
for the device.
Refactor this into the standard setup of a device having input
gpio lines.
This fixes a trivial Coverity memory leak report (the leon3
board code leaks the IRQ array returned from qemu_allocate_irqs()).
Fixes: Coverity CID 1421922
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212144134.29594-2-peter.maydell@linaro.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Per the "NCR89C105 Chip Specification" referenced in the header:
Chip-level Address Map
------------------------------------------------------------------
| 1D0 0000 -> | Counter/Timers | W,D |
| 1DF FFFF | | |
...
The address map indicated the allowed accesses at each address.
[...] W indicates a word access, and D indicates a double-word
access.
The SLAVIO timer controller is implemented expecting 32-bit accesses.
Commit a3d12d073e restricted the memory accesses to 32-bit, while
the device allows 64-bit accesses.
This was not an issue until commit 5d971f9e67 which reverted
("memory: accept mismatching sizes in memory_region_access_valid").
Fix by renaming .valid MemoryRegionOps as .impl, and add the valid
access range (W -> 4, D -> 8).
Since commit 21786c7e59 ("memory: Log invalid memory accesses")
this class of bug can be quickly debugged displaying 'guest_errors'
accesses, as:
$ qemu-system-sparc -M SS-20 -m 256 -bios ss20_v2.25_rom -serial stdio -d guest_errors
Power-ON Reset
Invalid access at addr 0x0, size 8, region 'timer-1', reason: invalid size (min:4 max:4)
$ qemu-system-sparc -M SS-20 -m 256 -bios ss20_v2.25_rom -monitor stdio -S
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
...
0000000ff1300000-0000000ff130000f (prio 0, i/o): timer-1
^^^^^^^^^ ^^^^^^^
\ memory region base address and name /
(qemu) info qtree
bus: main-system-bus
dev: slavio_timer, id "" <-- device type name
gpio-out "sysbus-irq" 17
num_cpus = 1 (0x1)
mmio 0000000ff1310000/0000000000000014
mmio 0000000ff1300000/0000000000000010 <--- base address
mmio 0000000ff1301000/0000000000000010
mmio 0000000ff1302000/0000000000000010
...
Reported-by: Yap KV <yapkv@yahoo.com>
Buglink: https://bugs.launchpad.net/bugs/1906905
Fixes: a3d12d073e ("slavio_timer: convert to memory API")
CC: qemu-stable@nongnu.org
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201205150903.3062711-1-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
First pull request for 2021, which has a bunch of things accumulated
over the holidays. Includes:
* A number of cleanups to sam460ex and ppc440 code from BALATON Zoltan
* Several fixes for builds with --without-default-devices from Greg Kurz
* Fixes for some DRC reset problems from Greg Kurz
* QOM conversion of the PPC 4xx UIC devices from Peter Maydell
* Some other assorted fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=7Eiy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210106' into staging
ppc patch queue 2021-01-06
First pull request for 2021, which has a bunch of things accumulated
over the holidays. Includes:
* A number of cleanups to sam460ex and ppc440 code from BALATON Zoltan
* Several fixes for builds with --without-default-devices from Greg Kurz
* Fixes for some DRC reset problems from Greg Kurz
* QOM conversion of the PPC 4xx UIC devices from Peter Maydell
* Some other assorted fixes and cleanups
# gpg: Signature made Wed 06 Jan 2021 03:33:19 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210106: (22 commits)
ppc440_pcix: Fix up pci config access
ppc440_pcix: Fix register write trace event
ppc440_pcix: Improve comment for IRQ mapping
sam460ex: Remove FDT_PPC dependency from KConfig
ppc4xx: Move common dependency on serial to common option
pnv: Fix reverse dependency on PCI express root ports
ppc: Simplify reverse dependencies of POWERNV and PSERIES on XICS and XIVE
ppc: Fix build with --without-default-devices
spapr: Add drc_ prefix to the DRC realize and unrealize functions
spapr: Use spapr_drc_reset_all() at machine reset
spapr: Introduce spapr_drc_reset_all()
spapr: Fix reset of transient DR connectors
spapr: Call spapr_drc_reset() for all DRCs at CAS
spapr: Fix buffer overflow in spapr_numa_associativity_init()
spapr: Allow memory unplug to always succeed
spapr: Fix DR properties of the root node
spapr/xive: Make spapr_xive_pic_print_info() static
spapr: DRC lookup cannot fail
hw/ppc/ppc440_bamboo: Drop use of ppcuic_init()
hw/ppc/virtex_ml507: Drop use of ppcuic_init()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fixes a long standing issue with MorphOS booting on sam460ex
which turns out to be because of suspicious values written to PCI
config address that apparently works on real machine but caused wrong
access on this device model. This replaces a previous work around for
this with a better fix that makes it work.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <6fd215ab2bc5f8d4455cd20ed1a2f059e4415fe5.1609636173.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The trace event for pci_host_config_write() was also using the trace
event for read. Add corresponding trace and correct this.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <a6c7dcf7153cc537123ed8ceac060f2f64a883cb.1609636173.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The code mapping all PCI interrupts to a single CPU IRQ works but is
not trivial so document it in a comment.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <c25c0310510672b58466e795fd701e65e8f1ff97.1609636173.git.balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Dependency on FDT_PPC was added in commit b0048f7609
("hw/ppc/Kconfig: Only select FDT helper for machines using it") but
it does not seem to be really necessary so remove it again.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <7461a20b129a912aeacdb9ad115a55f0b84c8726.1609636173.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All machines that select SERIAL also select PPC4XX so we can just add
this common dependency there once.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <94f1eb7cfb7f315bd883d825f3ce7e0cfc2f2b69.1609636173.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qemu-system-ppc64 built with --without-default-devices crashes:
Type 'pnv-phb4-root-port' is missing its parent 'pcie-root-port-base'
Aborted (core dumped)
Have POWERNV to select PCIE_PORT. This is done through a
new PCI_POWERNV config in hw/pci-host/Kconfig since POWERNV
doesn't have a direct dependency on PCI. For this reason,
PCI_EXPRESS and MSI_NONBROKEN are also moved under
PCI_POWERNV.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <160883058299.253005.342913177952681375.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Have PSERIES to select XICS and XIVE, and directly check PSERIES
in hw/intc/meson.build to enable build of the XICS and XIVE sPAPR
backends, like POWERNV already does. This allows to get rid of the
intermediate XICS_SPAPR and XIVE_SPAPR.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160883057560.253005.4206568349917633920.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Linking of the qemu-system-ppc64 fails on a POWER9 host when
--without-default-devices is passed to configure:
$ ./configure --without-default-devices \
--target-list=ppc64-softmmu && make
...
libqemu-ppc64-softmmu.fa.p/hw_ppc_e500.c.o: In function `ppce500_init_mpic_kvm':
/home/greg/Work/qemu/qemu-ppc/build/../hw/ppc/e500.c:777: undefined reference to `kvm_openpic_connect_vcpu'
libqemu-ppc64-softmmu.fa.p/hw_ppc_spapr_irq.c.o: In function `spapr_irq_check':
/home/greg/Work/qemu/qemu-ppc/build/../hw/ppc/spapr_irq.c:189: undefined reference to `xics_kvm_has_broken_disconnect'
libqemu-ppc64-softmmu.fa.p/hw_intc_spapr_xive.c.o: In function `spapr_xive_post_load':
/home/greg/Work/qemu/qemu-ppc/build/../hw/intc/spapr_xive.c:530: undefined reference to `kvmppc_xive_post_load'
... and tons of other symbols belonging to the KVM backend of the
openpic, XICS and XIVE interrupt controllers.
It turns out that OPENPIC_KVM, XICS_KVM and XIVE_KVM are marked
to depend on KVM but this has no effect when minikconf runs in
allnoconfig mode. Such reverse dependencies should rather be
handled with a 'select' statement, eg.
config OPENPIC
select OPENPIC_KVM if KVM
or even better by getting rid of the intermediate _KVM config
and directly checking CONFIG_KVM in the meson.build file:
specific_ss.add(when: ['CONFIG_KVM', 'CONFIG_OPENPIC'],
if_true: files('openpic_kvm.c'))
Go for the latter with OPENPIC, XICS and XIVE.
This went unnoticed so far because CI doesn't test the build with
--without-default-devices and KVM enabled on a POWER host.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160883056791.253005.14924294027763955653.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Use a less generic name for an easier experience with tools such as
cscope or grep.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-6-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Documentation of object_child_foreach_recursive() clearly stipulates
that "it is forbidden to add or remove children from @obj from the @fn
callback". But this is exactly what we do during machine reset. The call
to spapr_drc_reset() can finalize the hot-unplug sequence of a PHB or a
PCI bridge, both of which will then in turn destroy their PCI DRCs. This
could potentially invalidate the iterator used by do_object_child_foreach().
It is pure luck that this haven't caused any issues so far.
Use spapr_drc_reset_all() since it can cope with DRC removal.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-5-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
No need to expose the way DRCs are traversed outside of spapr_drc.c.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-4-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Documentation of object_property_iter_init() clearly stipulates that
"it is forbidden to modify the property list while iterating". But this
is exactly what we do when resetting transient DR connectors during CAS.
The call to spapr_drc_reset() can finalize the hot-unplug sequence of a
PHB or a PCI bridge, both of which will then in turn destroy their PCI
DRCs. This could potentially invalidate the iterator. It is pure luck
that this haven't caused any issues so far.
Change spapr_drc_reset() to return true if it caused a device to be
removed. Restart from scratch in this case. This can potentially
increase the overall DRC reset time, especially with a high maxmem
which generates a lot of LMB DRCs. But this kind of setup is rare,
and so is the use case of rebooting a guest while doing hot-unplug.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-3-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Non-transient DRCs are either in the empty or the ready state,
which means spapr_drc_reset() doesn't change their state. It
is thus not needed to do any checking. Call spapr_drc_reset()
unconditionally and squash spapr_drc_transient() into its
only user, spapr_drc_needed().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201218103400.689660-2-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is currently impossible to hot-unplug a memory device between
machine reset and CAS.
(qemu) device_del dimm1
Error: Memory hot unplug not supported for this guest
This limitation was introduced in order to provide an explicit
error path for older guests that didn't support hot-plug event
sources (and thus memory hot-unplug).
The linux kernel has been supporting these since 4.11. All recent
enough guests are thus capable of handling the removal of a memory
device at all time, including during early boot.
Lift the limitation for the latest machine type. This means that
trying to unplug memory from a guest that doesn't support it will
likely just do nothing and the memory will only get removed at
next reboot. Such older guests can still get the existing behavior
by using an older machine type.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160794035064.23292.17560963281911312439.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Section 13.5.2 of LoPAPR mandates various DR related indentifiers
for all hot-pluggable entities to be exposed in the "ibm,drc-indexes",
"ibm,drc-power-domains", "ibm,drc-names" and "ibm,drc-types" properties
of their parent node. These properties are created with spapr_dt_drc().
PHBs and LMBs are both children of the machine. Their DR identifiers
are thus supposed to be exposed in the afore mentioned properties of
the root node.
When PHB hot-plug support was added, an extra call to spapr_dt_drc()
was introduced: this overwrites the existing properties, previously
populated with the LMB identifiers, and they end up containing only
PHB identifiers. This went unseen so far because linux doesn't care,
but this is still not conformant with LoPAPR.
Fortunately spapr_dt_drc() is able to handle multiple DR entity types
at the same time. Use that to handle DR indentifiers for PHBs and LMBs
with a single call to spapr_dt_drc(). While here also account for PMEM
DR identifiers, which were forgotten when NVDIMM hot-plug support was
added. Also add an assert to prevent further misuse of spapr_dt_drc().
With -m 1G,maxmem=2G,slots=8 passed on the QEMU command line we get:
Without this patch:
/proc/device-tree/ibm,drc-indexes
0000001f 20000001 20000002 20000003
20000000 20000005 20000006 20000007
20000004 20000009 20000008 20000010
20000011 20000012 20000013 20000014
20000015 20000016 20000017 20000018
20000019 2000000a 2000000b 2000000c
2000000d 2000000e 2000000f 2000001a
2000001b 2000001c 2000001d 2000001e
These are the DRC indexes for the 31 possible PHBs.
With this patch:
/proc/device-tree/ibm,drc-indexes
0000002b 90000000 90000001 90000002
90000003 90000004 90000005 90000006
90000007 20000001 20000002 20000003
20000000 20000005 20000006 20000007
20000004 20000009 20000008 20000010
20000011 20000012 20000013 20000014
20000015 20000016 20000017 20000018
20000019 2000000a 2000000b 2000000c
2000000d 2000000e 2000000f 2000001a
2000001b 2000001c 2000001d 2000001e
80000004 80000005 80000006 80000007
And now we also have the 4 ((2G - 1G) / 256M) LMBs and the
8 (slots) PMEMs.
Fixes: 3998ccd092 ("spapr: populate PHB DRC entries for root DT node")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160794479566.35245.17809158217760761558.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All memory DRC objects are created during machine init. It is thus safe
to assume spapr_drc_by_id() cannot return NULL when hot-plug/unplugging
memory.
Make this clear with an assertion, like the code already does a few lines
above when looping over memory DRCs. This fixes Coverity reports 1437757
and 1437758.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160805381160.228955.5388294067094240175.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch the bamboo board to directly creating and configuring the UIC,
rather than doing it via the old ppcuic_init() helper function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212001537.24520-5-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch the virtex_ml507 board to directly creating and
configuring the UIC, rather than doing it via the old
ppcuic_init() helper function.
This fixes a trivial Coverity-detected memory leak where
we were leaking the array of IRQs returned by ppcuic_init().
Fixes: Coverity CID 1421992
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212001537.24520-4-peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently the PPC UIC ("Universal Interrupt Controller") is implemented
as a non-QOM device in ppc4xx_devs.c. Convert it to a proper QOM device
in hw/intc.
The ppcuic_init() function is retained for the moment with its current
interface; in subsequent commits this will be tidied up to avoid the
allocation of an irq array.
This conversion adds VMState support.
It leaves the LOG_UIC() macro as-is to maximise the extent to which
this is simply code-movement rather than a rewrite (in new code it
would be better to use tracepoints).
The default property values for dcr-base and use-vectors are set to
match those use by most of our boards with a UIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212001537.24520-3-peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In a following commit we will move the PPC UIC implementation to
its own file in hw/intc. To prevent checkpatch complaining about that
code-motion, fix up the minor style issues first.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212001537.24520-2-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Missed in 3ca7639ff0 ("hw/mips/fuloong2e: Set CPU frequency
to 533 MHz"), we need to tell the kernel the correct clock.
Fixes: 3ca7639ff0 ("hw/mips/fuloong2e: Set CPU frequency to 533 MHz").
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201224031750.52146-7-jiaxun.yang@flygoat.com>
[PMD: Reworded]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
modetty is not handled by kernel and the parameter
here seems unreasonable.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20201224031750.52146-6-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Do not remove busclock]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Websites are downing, but GitHub may last forever.
Loongson even doesn't recogonize 2E as their products nowadays..
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201224031750.52146-3-jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Seems useless....
Fixes: 051c190bce ("MIPS: Initial support of fulong mini pc (machine construction)")
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Message-Id: <20201224031750.52146-2-jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It will signed extend vaddr properly.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064200.28751-4-jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
So it will sign extend adresses properly.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064200.28751-3-jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Address should be unsigned anyway, otherwise it may carry
calculations wrongly.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064200.28751-2-jiaxun.yang@flygoat.com>
[PMD: Fixed typo and convert hw/mips/mipssim.c too]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add Loongson-3 based machine support, it use liointc as the interrupt
controler and use GPEX as the pci controller. Currently it can work with
both TCG and KVM.
As the machine model is not based on any exiting physical hardware, the
name of the machine is "loongson3-virt". It may be superseded in future
by a real machine model. If this happens, then a regular deprecation
procedure shall occur for "loongson3-virt" machine.
We now already have a full functional Linux kernel (based on Linux-5.4.x
LTS) here:
https://github.com/chenhuacai/linux
Of course the upstream kernel is also usable (the kvm host side and
guest side have both been upstream in Linux-5.9):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
How to use QEMU/Loongson-3?
1, Download kernel source from the above URL;
2, Build a kernel with arch/mips/configs/loongson3_defconfig;
3, Boot a Loongson-3A4000 host with this kernel (for KVM mode);
4, Build QEMU-master with this patchset;
5, modprobe kvm (only necessary for KVM mode);
6, Use QEMU with TCG:
qemu-system-mips64el -M loongson3-virt,accel=tcg -cpu Loongson-3A1000 -kernel <path_to_kernel> -append ...
Use QEMU with KVM:
qemu-system-mips64el -M loongson3-virt,accel=kvm -cpu Loongson-3A4000 -kernel <path_to_kernel> -append ...
The "-cpu" parameter is optional here and QEMU will use the correct type for TCG/KVM automatically.
Co-developed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20201221110538.3186646-5-chenhuacai@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Set TYPE_LOONGSON_MACHINE instance_size in TypeInfo,
select FW_CFG_MIPS in Kconfig]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Implement fw_cfg_arch_key_name(), which returns the name of a
mips-specific key.
Co-developed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1600742967-12933-7-git-send-email-chenhc@lemote.com>
[PMD: Add FW_CFG_MIPS Kconfig selector]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
As suggested by Philippe Mathieu-Daudé, rework Loongson's liointc:
1, Move macro definitions to loongson_liointc.h;
2, Remove magic values and use macros instead;
3, Replace dead D() code by trace events.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201221110538.3186646-2-chenhuacai@kernel.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's common to want to print a human-readable indication of a clock's
frequency. Provide a utility function in the clock API to return a
string which is a displayable representation of the frequency,
and use it in qdev-monitor.c.
Before:
(qemu) info qtree
[...]
dev: xilinx,zynq_slcr, id ""
clock-in "ps_clk" freq_hz=3.333333e+07
mmio 00000000f8000000/0000000000001000
After:
dev: xilinx,zynq_slcr, id ""
clock-in "ps_clk" freq_hz=33.3 MHz
mmio 00000000f8000000/0000000000001000
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215150929.30311-5-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use less confusing naming for superio config register handling related
parts that makes it clearer what belongs to this part.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <4d30a2b4b771b2ad651509885daae79d7c4fe7a8.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Rename local variable holding object state for readability and
consistency.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <69655b23df2ecebbf0aff29726f4b4746f5b74de.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These are not used or not needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <35cefcc3518a3395a796bb6ad6fbc308adc65266.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Drop DPRINTF and use trace functions instead. Two debug messages about
unimplemented registers could be converted to qemu_log_mask() but in
reality all registers are currently unimplemented (we just store and
return values of writable regs but do nothing with them). As we
already trace register access there's no need for additional debug
messages so these are just removed and a comment is added as a reminder.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <785854022a37035f66d89e70cb6ca1bc0e0d0163.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove legacy vt82c686b_pm_init() function and also rename
VT82C686B_PM type name to match other device names.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a70982b32f11222d335385b90749abb6cf2e2cce.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove some unneded, empty code and set user_creatable to false
(besides being not implemented yet, so does nothing anyway) it's also
normally part of VIA south bridge chips so no need to confuse users
showing them these devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <c7a5b1ee4c02e304ff70ebfbf269544f3c1f8412.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The via-[am]c97 code is supposed to implement the audio part of VIA
south bridge chips so it is better placed under hw/audio/. Split it
off into a separate file.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <af083634e3b9efe67e6c4247cf0185d3fa7b1810.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These are legacy init functions that are just equivalent to directly
calling pci_create_simple so do that instead. Also rename objects to
lower case via-ac97 and via-mc97 matching naming of other devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1c4373c8aeb6c4fb2a8df2c864b0e91a977a3d7b.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is really the ISA bridge part so name the type accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <78db2ced4b41a8a775dbc6c97a90db683952c2cb.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There's no reason to suffix everything with _DEVICE when the names are
already unique without it and shorter names are more readable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <ea89683ebb3528c0f79ed99d3d3cfcefb63c3bfb.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These parts are common between VT82C686B and VT8231 so can be shared
in the future. Rename them to VIA prefix accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <510ddb17836a2c2e68a27cf2dcaee420bc2efbc1.1609584215.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We already have a generic PCI_DEVFN() macro in "hw/pci/pci.h"
to pack the PCI slot/function identifiers, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201012124506.3406909-6-philmd@redhat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201231224911.1467352-4-f4bug@amsat.org>
We already have a generic PCI_SLOT() macro in "hw/pci/pci.h"
to extract the PCI slot identifier, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201012124506.3406909-5-philmd@redhat.com>
We already have a generic PCI_FUNC() macro in "hw/pci/pci.h" to
extract the PCI function identifier, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201012124506.3406909-4-philmd@redhat.com>
We already have a generic PCI_BUILD_BDF() macro in "hw/pci/pci.h"
to pack these values, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201012124506.3406909-3-philmd@redhat.com>
Enable removing tcg/$tcg_arch from the include path when TCG is disabled.
Move translate-all.h to include/exec, since stubs exist for the functions
defined therein.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- enhance the s390 devices acceptance test
- tcg: improve carry computation
- qga: send the ccw address with the fsinfo data
- fixes for protected virtualisation and zpci
-----BEGIN PGP SIGNATURE-----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=X/jY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck-gitlab/tags/s390x-20201222' into staging
Further s390x updates:
- enhance the s390 devices acceptance test
- tcg: improve carry computation
- qga: send the ccw address with the fsinfo data
- fixes for protected virtualisation and zpci
# gpg: Signature made Tue 22 Dec 2020 10:37:34 GMT
# gpg: using RSA key C3D0D66DC3624FF6A8C018CEDECF6B93C6F02FAF
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck-gitlab/tags/s390x-20201222:
tests/acceptance: Add a test with the Fedora 31 kernel and initrd
s390x/pci: Fix memory_region_access_valid call
s390x/pci: fix pcistb length
tests/acceptance: Test the virtio-balloon device on s390x
tests/acceptance: Test virtio-rng on s390 via /dev/hwrng
tests/acceptance: Extract the code to clear dmesg and wait for CRW reports
tests/acceptance: test hot(un)plug of ccw devices
target/s390x: Improve SUB LOGICAL WITH BORROW
target/s390x: Improve cc computation for SUBTRACT LOGICAL
target/s390x: Improve ADD LOGICAL WITH CARRY
target/s390x: Improve cc computation for ADD LOGICAL
qga/commands-posix: Send CCW address on s390x with the fsinfo data
MAINTAINERS: move my git tree to gitlab
s390x: pv: Fence additional unavailable SCLP facilities for PV guests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=vGLy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-qapi-2020-12-19' into staging
QAPI patches patches for 2020-12-19
# gpg: Signature made Sat 19 Dec 2020 09:40:05 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2020-12-19: (33 commits)
qobject: Make QString immutable
block: Use GString instead of QString to build filenames
keyval: Use GString to accumulate value strings
json: Use GString instead of QString to accumulate strings
migration: Replace migration's JSON writer by the general one
qobject: Factor JSON writer out of qobject_to_json()
qobject: Factor quoted_str() out of to_json()
qobject: Drop qstring_get_try_str()
qobject: Drop qobject_get_try_str()
Revert "qobject: let object_property_get_str() use new API"
block: Avoid qobject_get_try_str()
qmp: Fix tracing of non-string command IDs
qobject: Move internals to qobject-internal.h
hw/rdma: Replace QList by GQueue
Revert "qstring: add qstring_free()"
qobject: Change qobject_to_json()'s value to GString
qobject: Use GString instead of QString to accumulate JSON
qobject: Make qobject_to_json_pretty() take a pretty argument
monitor: Use GString instead of QString for output buffer
hmp: Simplify how qmp_human_monitor_command() gets output
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Add qemu-storage-daemon documentation
- hw/block/nand: Decommission the NAND museum
- vpc: Clean up some buffer abuse
- nfs: fix int overflow in nfs_client_open_qdict
- Several iotests fixes
-----BEGIN PGP SIGNATURE-----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=yLZI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Add qemu-storage-daemon documentation
- hw/block/nand: Decommission the NAND museum
- vpc: Clean up some buffer abuse
- nfs: fix int overflow in nfs_client_open_qdict
- Several iotests fixes
# gpg: Signature made Fri 18 Dec 2020 12:07:30 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
block/vpc: Use sizeof() instead of HEADER_SIZE for footer size
block/vpc: Pass footer buffers as VHDFooter * instead of uint8_t *
block/vpc: Pad VHDFooter, replace uint8_t[] buffers
block/vpc: Use sizeof() instead of 1024 for dynamic header size
block/vpc: Pad VHDDynDiskHeader, replace uint8_t[] buffers
block/vpc: Make vpc_checksum() take void *
block/vpc: Don't abuse the footer buffer for dynamic header
block/vpc: Don't abuse the footer buffer as BAT sector buffer
block/vpc: Make vpc_open() read the full dynamic header
iotests:172: use _filter_qom_path
iotests: make _filter_qom_path more strict
MAINTAINERS: add Kevin Wolf as storage daemon maintainer
docs: add qemu-storage-daemon(1) man page
docs: generate qemu-storage-daemon-qmp-ref(7) man page
block/nfs: fix int overflow in nfs_client_open_qdict
hw/block/nand: Decommission the NAND museum
iotests/210: Fix reference output
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In pcistb_service_handler, a call is made to validate that the memory
region can be accessed. However, the call is made using the entire length
of the pcistb operation, which can be larger than the allowed memory
access size (8). Since we already know that the provided buffer is a
multiple of 8, fix the call to memory_region_access_valid to iterate
over the memory region in the same way as the subsequent call to
memory_region_dispatch_write.
Fixes: 863f6f52b7 ("s390: implement pci instructions")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1608243397-29428-3-git-send-email-mjrosato@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
In pcistb_service_call, we are grabbing 8 bits from a guest register to
indicate the length of the store operation -- but per the architecture
the length is actually defined by 13 bits of the guest register.
Fixes: 863f6f52b7 ("s390: implement pci instructions")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1608243397-29428-2-git-send-email-mjrosato@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 8118f0950f "migration: Append JSON description of migration
stream" needs a JSON writer. The existing qobject_to_json() wasn't a
good fit, because it requires building a QObject to convert. Instead,
migration got its very own JSON writer, in commit 190c882ce2 "QJSON:
Add JSON writer". It tacitly limits numbers to int64_t, and strings
contents to characters that don't need escaping, unlike
qobject_to_json().
The previous commit factored the JSON writer out of qobject_to_json().
Replace migration's JSON writer by it.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201211171152.146877-17-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
RdmaProtectedQList provides a thread-safe queue of int64_t on top of a
QList.
rdma_protected_qlist_destroy() calls qlist_destroy_obj() directly.
qlist_destroy_obj() is actually for use by qobject_destroy() only.
The next commit will make that obvious.
The minimal fix would be calling qobject_unref() instead. But QList
is actually a bad fit here. It's designed for representing JSON
arrays. We're better off with a GQueue here. Replace.
Cc: Yuval Shaia <yuval.shaia.ml@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201211171152.146877-8-armbru@redhat.com>
Anywhere we create a list of just one item or by prepending items
(typically because order doesn't matter), we can use
QAPI_LIST_PREPEND(). But places where we must keep the list in order
by appending remain open-coded until later patches.
Note that as a side effect, this also performs a cleanup of two minor
issues in qga/commands-posix.c: the old code was performing
new = g_malloc0(sizeof(*ret));
which 1) is confusing because you have to verify whether 'new' and
'ret' are variables with the same type, and 2) would conflict with C++
compilation (not an actual problem for this file, but makes
copy-and-paste harder).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20201113011340.463563-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
[Straightforward conflicts due to commit a8aa94b5f8 "qga: update
schema for guest-get-disks 'dependents' field" and commit a10b453a52
"target/mips: Move mips_cpu_add_definition() from helper.c to cpu.c"
resolved. Commit message tweaked.]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Instead of modifying the value member of a list element passed as a
parameter, and open-coding the manipulation of that list, it's nicer
to just return a freshly allocated value to be prepended to a list
using QAPI_LIST_PREPEND.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20201113011340.463563-3-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We're just doing pointer math with the device pointer, we can
simply use obj instead.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-32-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The function will be moved to common QOM code, as it is not
specific to TYPE_DEVICE anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the variable declaration close to the macro that uses it.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-29-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Support Property.set_default and PropertyInfo.description even if
PropertyInfo.create is set.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-26-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Returning ObjectProperty* will be useful for new property
registration code that will add additional callbacks
to ObjectProperty after registering it.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-25-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every single qdev property setter function manually checks
dev->realized. We can just check dev->realized inside
qdev_property_set() instead.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-24-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We'll add extra code to the qdev property getters and setters, so
add wrapper functions where additional actions can be performed.
The new functions have a "field_prop_" prefix instead of "qdev_"
because the code will eventually be moved outside
qdev-properties.c, to common QOM code.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-23-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make it easier to remove the Property.name field in the
future.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-22-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make it easier to remove Property.name in the future.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20201211220529.2290218-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We already get the property name as argument to the property
getter and setters, we don't need to use prop->name. This will
make it easier to remove the Property.name field in the future.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-20-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Replace `Property *prop` parameter with `char *name`, to reduce
dependency of getter and setter functions on the Property struct
(which will be changed in following patches).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201211220529.2290218-19-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This is the QEMU equivalent of this Linux commit (but 7 years later):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f7025a43a9da2
The MTD subsystem has its own small museum of ancient NANDs
in a form of the CONFIG_MTD_NAND_MUSEUM_IDS configuration option.
The museum contains stone age NANDs with 256 bytes pages, as well
as iron age NANDs with 512 bytes per page and up to 8MiB page size.
It is with great sorrow that I inform you that the museum is being
decommissioned. The MTD subsystem is out of budget for Kconfig
options and already has too many of them, and there is a general
kernel trend to simplify the configuration menu.
We remove the stone age exhibits along with closing the museum,
but some of the iron age ones are transferred to the regular NAND
depot. Namely, only those which have unique device IDs are
transferred, and the ones which have conflicting device IDs are
removed.
The machine using this device are:
- axis-dev88
- tosa (via tc6393xb_init)
- spitz based (akita, borzoi, terrier)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201214002620.342384-1-f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add missing 'break' to fix:
hw/rtc/twl92230.c: In function ‘menelaus_write’:
hw/rtc/twl92230.c:713:5: error: label at end of compound statement
713 | default:
| ^~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201211154605.511714-1-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When using -Wimplicit-fallthrough in our CFLAGS, the compiler showed warning:
hw/intc/arm_gicv3_kvm.c: In function ‘kvm_arm_gicv3_put’:
hw/intc/arm_gicv3_kvm.c:484:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
kvm_gicc_access(s, ICC_AP0R_EL1(1), ncpu, ®64, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_kvm.c:485:9: note: here
default:
^~~~~~~
hw/intc/arm_gicv3_kvm.c:495:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
kvm_gicc_access(s, ICC_AP1R_EL1(2), ncpu, ®64, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_kvm.c:496:9: note: here
case 6:
^~~~
hw/intc/arm_gicv3_kvm.c:498:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
kvm_gicc_access(s, ICC_AP1R_EL1(1), ncpu, ®64, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_kvm.c:499:9: note: here
default:
^~~~~~~
hw/intc/arm_gicv3_kvm.c: In function ‘kvm_arm_gicv3_get’:
hw/intc/arm_gicv3_kvm.c:634:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G0][2] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:635:9: note: here
case 6:
^~~~
hw/intc/arm_gicv3_kvm.c:637:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G0][1] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:638:9: note: here
default:
^~~~~~~
hw/intc/arm_gicv3_kvm.c:648:39: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G1NS][2] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:649:9: note: here
case 6:
^~~~
hw/intc/arm_gicv3_kvm.c:651:39: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G1NS][1] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:652:9: note: here
default:
^~~~~~~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201211152426.350966-7-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When using -Wimplicit-fallthrough in our CFLAGS, the compiler showed warning:
../hw/timer/renesas_tmr.c: In function ‘tmr_read’:
../hw/timer/renesas_tmr.c:221:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
221 | } else if (ch == 0) {i
| ^
../hw/timer/renesas_tmr.c:224:5: note: here
224 | case A_TCORB:
| ^~~~
Add the corresponding "fall through" comment to fix it.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201211152426.350966-5-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When compiling with -Werror=implicit-fallthrough, gcc complains about
missing fallthrough annotations in this file. Looking at the code,
the fallthrough is indeed wanted here, but instead of adding the
annotations, it can be done more efficiently by simply calculating
the offset with a subtraction instead of increasing a local variable
one by one.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201211152426.350966-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Instead of using string compares to determine if a RISC-V machine is
using 32-bit or 64-bit CPUs we can use the initalised CPUs. This avoids
us having to maintain a list of CPU names to compare against.
This commit also fixes the name of the function to match the
riscv_cpu_is_32bit() function.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 8ab7614e5df93ab5267788b73dcd75f9f5615e82.1608142916.git.alistair.francis@wdc.com
Currently the riscv_is_32_bit() function only supports the generic rv32
CPUs. Extend the function to support the SiFive and LowRISC CPUs as
well.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-id: 9a13764115ba78688ba61b56526c6de65fc3ef42.1608142916.git.alistair.francis@wdc.com
Previously if an interrupt occured during the claim process (after the
interrupt is claimed but before it's completed) it would never be
cleared.
This patch ensures that we also clear the hidden_pending bits as well.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Jackie Ke <jackieke724@hotmail.com>
Message-id: 4e9786084a86f220689123cc8a7837af8fa071cf.1607100423.git.alistair.francis@wdc.com
Fix code style. Don't use '#' flag of printf format ('%#') in
format strings, use '0x' prefix instead
Signed-off-by: Xinhao Zhang <zhangxinhao1@huawei.com>
Signed-off-by: Kai Deng <dengkai1@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201116140148.2850128-1-zhangxinhao1@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The sifive_u machine emulates two UARTs but we have only UART0 DT
node in the generated DTB so this patch adds UART1 DT node in the
generated DTB.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201111094725.3768755-1-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In the previous commits we made cpu_exec_* and debug_excp_handler
optional, so we can now remove these no-op handlers.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201212155530.23098-13-cfontana@suse.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
fw-path-provider.c is only consumed by qdev-fw.c, which itself
is in softmmu_ss[], so we can restrict fw-path-provider.c to
softmmu too.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201207220709.4017938-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is (mostly theoretical) race between removal of a scsi device and
scsi_dma_restart_bh.
It used to be easier to hit this race prior to my / Paulo's patch series
that added rcu to scsi bus device handling code, but IMHO this race
should still be possible to hit, at least in theory.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1854811
Fix it anyway with a patch that was proposed by Paulo in the above bugzilla.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201210125929.1136390-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Machine options can be retrieved as properties of the machine object.
Encourage that by removing the "easy" accessor to machine options.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since NVDIMM support was introduced on pseries machine,
it ignored machine's nvdimm=on|off option and effectively
was always enabled on machines that support NVDIMM.
Later on commit
(28f5a71621 ppc/spapr_nvdimm: do not enable support with 'nvdimm=off')
makes QEMU error out in case user explicitly set 'nvdimm=off'
on CLI by peeking at machine_opts.
However that's a workaround and leaves 'nvdimms_state->is_enabled'
in inconsistent state (false) when it should be set true
by default.
Instead of using on machine_opts, set default to true for pseries
machine in initfn time. If user sets manually 'nvdimm=off'
it will overwrite default value to false and QEMU will error
as expected without need to peek into machine_opts.
That way pseries will have, nvdimm enabled by default and
will honor user provided 'nvdimm=on|off'.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201208164606.4109134-1-imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Generalize the qdev_hotplug variable to the different phases of
machine initialization. We would like to allow different
monitor commands depending on the phase.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
machine_init_done is not the right flag to check when preconfig
is taken into account; for example "./qemu-system-x86_64 -serial
mon:stdio -preconfig" does not print the QEMU monitor header until after
exit_preconfig. Add back a custom bool for mux character devices. This
partially undoes commit c7278b4355 ("chardev: introduce chr_machine_done
hook", 2018-03-12), but it keeps the cleaner logic using a function
pointer in ChardevClass.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qdev_machine_creation_done is only setting a flag now. Extend it to
move more code out of vl.c. Leave only consistency checks and gdbserver
processing in qemu_machine_creation_done.
gdbserver_start can be moved after qdev_machine_creation_done because
it only does listen on the socket and creates some internal data
structures; it does not send any data (e.g. guest state) over the socket.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The preconfig state is only used if -incoming is not specified, which
makes the RunState state machine more tricky than it need be. However
there is already an equivalent condition which works even with -incoming,
namely qdev_hotplug. Use it instead of a separate runstate.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
-----BEGIN PGP SIGNATURE-----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=lHZA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20201215' into staging
target-arm queue:
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
# gpg: Signature made Tue 15 Dec 2020 13:59:46 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20201215:
hw/block/m25p80: Fix Numonyx fast read dummy cycle count
hw/block/m25p80: Check SPI mode before running some Numonyx commands
hw/block/m25p80: Fix when VCFG XIP bit is set for Numonyx
hw/block/m25p80: Make Numonyx config field names more accurate
hw/misc/zynq_slcr: Avoid #DIV/0! error
arm: xlnx-versal: Connect usb to virt-versal
usb: xlnx-usb-subsystem: Add xilinx usb subsystem
usb: Add DWC3 model
usb: Add versal-usb2-ctrl-regs module
elf_ops.h: Be more verbose with ROM blob names
elf_ops.h: Don't truncate name of the ROM blobs we create
hw/core/loader.c: Improve reporting of ROM overlap errors
hw/core/loader.c: Track last-seen ROM in rom_check_and_register_reset()
target/nios2: Use deposit32() to update ipending register
target/nios2: Move nios2_check_interrupts() into target/nios2
target/nios2: Move IIC code into CPU object proper
target/openrisc: Move pic_cpu code into CPU object proper
hw/openrisc/openrisc_sim: Abstract out "get IRQ x of CPU y"
hw/openrisc/openrisc_sim: Use IRQ splitter when connecting IRQ to multiple CPUs
gdbstub: Correct misparsing of vCont C/S requests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only softmmu code uses DEFINE_PROP_UUID, and it currently depends
on error_set_from_qdev_prop_error(). Move it to
qdev-properties-system.c to get out of our way when refactoring
the qdev property system.
We can eventually move it back to the core property system later,
after removing usage of error_set_from_qdev_prop_error().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-15-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
There are no users of the function outside qdev-properties.c.
Make function static and rename it to get_uint16().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-14-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> #s390 parts
Message-Id: <20201211220529.2290218-13-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-12-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> #s390 parts
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-10-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-8-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
All other qdev property error messages use "<type>.<property>"
instead of "<id>.<property>". Change set_size32() for consistency,
and to make the code not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This setter is one of the very few property setters that don't
check dev->realized, and there's no reason to make size
properties different from the rest. Add the missing check.
Fixes: e8cd45c78f ("qdev: Add SIZE type to qdev properties")
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-5-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move everything related to Property and PropertyInfo to
qdev-properties.[ch] to make it easier to refactor that code.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
There's no reason to keep the property list separate from the CPU
class code. Move the variable to hw/core/cpu.c and make it
static.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
An empty props array is unnecessary, we can just not call
device_class_set_props().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20201211220529.2290218-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Note: "its" is currently registered conditionally, but this makes
the feature be registered unconditionally. The only side effect
is that it will be now possible to set its=on on virt-2.7 and
older.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some Numonyx flash commands cannot be executed in DIO and QIO mode, such as
trying to do DPP or DOR when in QIO mode.
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-4-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VCFG XIP is set (disabled) when the NVCFG XIP bits are all set (disabled).
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-3-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous naming of the configuration registers made it sound like that if
the bits were set the settings would be enabled, while the opposite is true.
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-2-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Malicious user can set the feedback divisor for the PLLs
to zero, triggering a floating-point exception (SIGFPE).
As the datasheet [*] is not clear how hardware behaves
when these bits are zeroes, use the maximum divisor
possible (128) to avoid the software FPE.
[*] Zynq-7000 TRM, UG585 (v1.12.2)
B.28 System Level Control Registers (slcr)
-> "Register (slcr) ARM_PLL_CTRL"
25.10.4 PLLs
-> "Software-Controlled PLL Update"
Fixes: 38867cb7ec ("hw/misc/zynq_slcr: add clock generation for uarts")
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20201210141610.884600-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect VersalUsb2 subsystem to xlnx-versal SOC, its placed
in iou of lpd domain and configure it as dual port host controller.
Add the respective guest dts nodes for "xlnx-versal-virt" machine.
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1607023357-5096-5-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This model is a top level integration wrapper for hcd-dwc3 and
versal-usb2-ctrl-regs modules, this is used by xilinx versal soc's and
future xilinx usb subsystems would also be part of it.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1607023357-5096-4-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds skeleton model of dwc3 usb controller attached to
xhci-sysbus device. It defines global register space of DWC3 controller,
global registers control the AXI/AHB interfaces properties, external FIFO
support and event count support. All of which are unimplemented at
present,we are only supporting core reset and read of ID register.
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1607023357-5096-3-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This module emulates control registers of versal usb2 controller, this is added
just to make guest happy. In general this module would control the phy-reset
signal from usb controller, data coherency of the transactions, signals
the host system errors received from controller.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1607023357-5096-2-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In rom_check_and_register_reset() we report to the user if there is
a "ROM region overlap". This has a couple of problems:
* the reported information is not very easy to intepret
* the function just prints the overlap to stderr (and relies on
its single callsite in vl.c to do an error_report() and exit)
* only the first overlap encountered is diagnosed
Make this function use error_report() and error_printf() and
report a more user-friendly report with all the overlaps
diagnosed.
Sample old output:
rom: requested regions overlap (rom dtb. free=0x0000000000008000, addr=0x0000000000000000)
qemu-system-aarch64: rom check and register reset failed
Sample new output:
qemu-system-aarch64: Some ROM regions are overlapping
These ROM regions might have been loaded by direct user request or by default.
They could be BIOS/firmware images, a guest kernel, initrd or some other file loaded into guest memory.
Check whether you intended to load all this guest code, and whether it has been built to load to the correct addresses.
The following two regions overlap (in the cpu-memory-0 address space):
phdr #0: /home/petmay01/linaro/qemu-misc-tests/ldmia-fault.axf (addresses 0x0000000000000000 - 0x0000000000008000)
dtb (addresses 0x0000000000000000 - 0x0000000000100000)
The following two regions overlap (in the cpu-memory-0 address space):
phdr #1: /home/petmay01/linaro/qemu-misc-tests/bad-psci-call.axf (addresses 0x0000000040000000 - 0x0000000040000010)
phdr #0: /home/petmay01/linaro/qemu-misc-tests/bp-test.elf (addresses 0x0000000040000000 - 0x0000000040000020)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201129203923.10622-3-peter.maydell@linaro.org
In rom_check_and_register_reset() we detect overlaps by looking at
whether the ROM blob we're currently examining is in the same address
space and starts before the previous ROM blob ends. (This works
because the ROM list is kept sorted in order by AddressSpace and then
by address.)
Instead of keeping the AddressSpace and last address of the previous ROM
blob in local variables, just keep a pointer to it.
This will allow us to print more useful information when we do detect
an overlap.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201129203923.10622-2-peter.maydell@linaro.org
The function nios2_check_interrupts)() looks only at CPU-internal
state; it belongs in target/nios2, not hw/nios2. Move it into the
same file as its only caller, so it can just be local to that file.
This removes the only remaining code from cpu_pic.c, so we can delete
that file entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201129174022.26530-3-peter.maydell@linaro.org
Reviewed-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Wentong Wu <wentong.wu@intel.com>
The Nios2 architecture supports two different interrupt controller
options:
* The IIC (Internal Interrupt Controller) is part of the CPU itself;
it has 32 IRQ input lines and no NMI support. Interrupt status is
queried and controlled via the CPU's ipending and istatus
registers.
* The EIC (External Interrupt Controller) interface allows the CPU
to connect to an external interrupt controller. The interface
allows the interrupt controller to present a packet of information
containing:
- handler address
- interrupt level
- register set
- NMI mode
QEMU does not model an EIC currently. We do model the IIC, but its
implementation is split across code in hw/nios2/cpu_pic.c and
hw/intc/nios2_iic.c. The code in those two files has no state of its
own -- the IIC state is in the Nios2CPU state struct.
Because CPU objects now inherit (indirectly) from TYPE_DEVICE, they
can have GPIO input lines themselves, so we can implement the IIC
directly in the CPU object the same way that real hardware does.
Create named "IRQ" GPIO inputs to the Nios2 CPU object, and make the
only user of the IIC wire up directly to those instead.
Note that the old code had an "NMI" concept which was entirely unused
and also as far as I can see not architecturally correct, since only
the EIC has a concept of an NMI.
This fixes a Coverity-reported trivial memory leak of the IRQ array
allocated in nios2_cpu_pic_init().
Fixes: Coverity CID 1421916
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201129174022.26530-2-peter.maydell@linaro.org
Reviewed-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Wentong Wu <wentong.wu@intel.com>
The openrisc code uses an old style of interrupt handling, where a
separate standalone set of qemu_irqs invoke a function
openrisc_pic_cpu_handler() which signals the interrupt to the CPU
proper by directly calling cpu_interrupt() and cpu_reset_interrupt().
Because CPU objects now inherit (indirectly) from TYPE_DEVICE, they
can have GPIO input lines themselves, and the neater modern way to
implement this is to simply have the CPU object itself provide the
input IRQ lines.
Create GPIO inputs to the OpenRISC CPU object, and make the only user
of cpu_openrisc_pic_init() wire up directly to those instead.
This allows us to delete the hw/openrisc/pic_cpu.c file entirely.
This fixes a trivial memory leak reported by Coverity of the IRQs
allocated in cpu_openrisc_pic_init().
Fixes: Coverity CID 1421934
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Message-id: 20201127225127.14770-4-peter.maydell@linaro.org
We're about to refactor the OpenRISC pic_cpu code in a way that means
that just grabbing the whole qemu_irq[] array of inbound IRQs for a
CPU won't be possible any more. Abstract out a function for "return
the qemu_irq for IRQ x input of CPU y" so we can more easily replace
the implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Message-id: 20201127225127.14770-3-peter.maydell@linaro.org
openrisc_sim_net_init() attempts to connect the IRQ line from the
ethernet device to both CPUs in an SMP configuration by simply caling
sysbus_connect_irq() for it twice. This doesn't work, because the
second connection simply overrides the first.
Fix this by creating a TYPE_SPLIT_IRQ to split the IRQ in the SMP
case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Message-id: 20201127225127.14770-2-peter.maydell@linaro.org
An empty props array is unnecessary, we can just not call
device_class_set_props().
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20201211220529.2290218-2-ehabkost@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
-----BEGIN PGP SIGNATURE-----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=aOV/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging
Pull request trivial-patches 20201214
# gpg: Signature made Mon 14 Dec 2020 15:52:07 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.0-pull-request:
configure / meson: Move check for linux/btrfs.h to meson.build
configure / meson: Move check for sys/kcov.h to meson.build
configure / meson: Move check for sys/signal.h to meson.build
configure / meson: Move check for drm.h to meson.build
configure / meson: Move check for pty.h to meson.build
configure: Remove the obsolete check for ifaddrs.h
blockdev: Fix a memleak in drive_backup_prepare()
block/file-posix: fix a possible undefined behavior
elf2dmp/pdb: Plug memleak in pdb_init_from_file
elf2dmp/qemu_elf: Plug memleak in QEMU_Elf_init
configure: Test if $make actually exists
ads7846: moves from the hw/display folder to the hw/input folder.
CODING_STYLE.rst: Be less strict about 80 character limit
fsdev: open brace '{' following struct go on the same line
hw/pci-host/pam: Replace magic number by PAM_REGIONS_COUNT definition
hw/xen: Don't use '#' flag of printf format
MAINTAINERS: update my email address
qemu-options.hx: Fix minor issues in icount documentation
target/i386: tracing: format length values as hex
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
spapr_kvm_type() is considering 'vm_type=NULL' as a valid input, where
the function returns 0. This is relying on the current QEMU machine
options handling logic, where the absence of the 'kvm-type' option
will be reflected as 'vm_type=NULL' in this function.
This is not robust, and will break if QEMU options code decides to propagate
something else in the case mentioned above (e.g. an empty string instead
of NULL).
Let's avoid this entirely by setting a non-NULL default value in case of
no user input for 'kvm-type'. spapr_kvm_type() was changed to handle 3 fixed
values of kvm-type: "auto", "hv", and "pr", with "auto" being the default
if no kvm-type was set by the user. This allows us to always be predictable
regardless of any enhancements/changes made in QEMU options mechanics.
While we're at it, let's also document in 'kvm-type' description the
already existing default mode, now named 'auto'. The information provided
about it is based on how the pseries kernel handles the KVM_CREATE_VM
ioctl(), where the default value '0' makes the kernel choose an available
KVM module to use, giving precedence to kvm_hv. This logic is described in
the kernel source file arch/powerpc/kvm/powerpc.c, function kvm_arch_init_vm().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20201210145517.1532269-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Some functions in hw/ppc/spapr_events.c get a pointer to the machine
state using qdev_get_machine(). Convert them to get it from their
caller when possible.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201209170052.1431440-6-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_phb_realize() passes the sPAPR machine state as opaque data
for the I/O callbacks:
memory_region_init_io(&sphb->msiwindow, OBJECT(sphb), &spapr_msi_ops, spapr,
^^^^^
"msi", msi_window_size);
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201209170052.1431440-5-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows to drop a user of qdev_get_machine().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201209170052.1431440-4-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When running qom-test, a memory leak occurred in the ppce500_init function,
this patch free irqs array to fix it.
ASAN shows memory leak stack:
Direct leak of 40 byte(s) in 1 object(s) allocated from:
#0 0xfffc5ceee1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xfffc5c806800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaacf9999244 in ppce500_init qemu/hw/ppc/e500.c:859
#3 0xaaacf97434e8 in machine_run_board_init qemu/hw/core/machine.c:1134
#4 0xaaacf9c9475c in qemu_init qemu/softmmu/vl.c:4369
#5 0xaaacf94785a0 in main qemu/softmmu/main.c:49
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Message-Id: <20201204075822.359832-1-ganqixin@huawei.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A guest with enough RAM, eg. 128G, is likely to detect savevm downtime
and to complain about stalled CPUs. This happens because we re-read
the timebase just before migrating it and we thus don't account for
all the time between VM stop and pre-save.
A very similar situation was already addressed for live migration of
paused guests (commit d14f339762). Extend the logic to do the same
with savevm.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1893787
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160693010619.1111945.632640981169395440.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All users are passing &error_abort already. Document the fact
that spapr_drc_attach() should only be passed a free DRC, which
is supposedly the case if appropriate checking is done earlier.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201201113728.885700-5-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_core_pre_plug() already guarantees that the slot for the given core
ID is available. It is thus safe to assume that spapr_find_cpu_slot()
returns a slot during plug. Turn the error path into an assertion.
It is also safe to assume that no device is attached to the corresponding
DRC and that spapr_drc_attach() shouldn't fail.
Pass &error_abort to spapr_drc_attach() and simplify error handling.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201201113728.885700-4-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU is hot-plugged, we set its compat mode to match the boot
CPU, which was either set by machine reset or by CAS. This is currently
handled in the plug handler after the core got realized. Potential errors
of ppc_set_compat() are propagated to the hot-plug logic.
Handling errors this late in the hot-plug sequence is generally frown
upon. Ideally, we should do sanity checks in a pre-plug handler and pass
&error_abort to ppc_set_compat() in the plug handler.
We can filter out some error cases of ppc_set_compat() by calling
ppc_check_compat() at pre-plug. But ppc_set_compat() also sets the
compat register in KVM, and KVM doesn't provide any API that would
allow to check valid compat mode settings beforehand.
However, at this point we know that the compat mode was already
successfully set for the boot CPU. Since this all boils down to
setting a register with the very same value that was valid
for the boot CPU, it should definitely not fail for hot-plugged
CPUS.
Pass &error_abort to ppc_set_compat().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201201113728.885700-3-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This hack registers dummy VMState entries of ICPs in order to
support migration of old pseries machine types that used to
create all smp.max_cpus possible ICPs at machine init.
Part of the work is to unregister the dummy entries when plugging
an actual vCPU core, and to register them back when unplugging the
core. The code that unregisters the dummy ICPs in spapr_core_plug()
is misplaced: if ppc_set_compat() fails afterwards, the hotplug
operation will be cancelled and the dummy ICPs won't be registered
back since the unplug handler isn't called.
Unregister the dummy ICPs at the end of spapr_core_plug().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201201113728.885700-2-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
I have been keeping those logging messages in an ugly form for
while. Make them clean !
Beware not to activate all of them, this is really verbose.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201123163717.1368450-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The '%u' conversion specifier is for decimal notation.
When prefixing a format with '0x', we want the hexadecimal
specifier ('%x').
Inspired-by: Dov Murik <dovmurik@linux.vnet.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201103112558.2554390-4-philmd@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -Wimplicit-fallthrough in our CFLAGS, the compiler showed warning:
hw/ppc/ppc.c: In function ‘ppc6xx_set_irq’:
hw/ppc/ppc.c:118:16: warning: this statement may fall through [-Wimplicit-fallthrough=]
118 | if (level) {
| ^
hw/ppc/ppc.c:123:9: note: here
123 | case PPC6xx_INPUT_INT:
| ^~~~
According to the discussion, a break statement needs to be added here.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201116024810.2415819-7-kuhn.chenqun@huawei.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There can be only one TPM proxy at a time. This is currently
checked at plug time. But this can be detected at pre-plug in
order to error out earlier.
This allows to get rid of error handling in the plug handler.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120234208.683521-9-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We currently detect that a PHB index is already in use at plug time.
But this can be decteted at pre-plug in order to error out earlier.
This allows to pass &error_abort to spapr_drc_attach() and to end
up with a plug handler that doesn't need to report errors anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120234208.683521-8-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Read documentation in "qapi/error.h" and changelog of commit
e3fe3988d7 ("error: Document Error API usage rules") for
rationale.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120234208.683521-7-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Pre-plug of a memory device, be it an NVDIMM or a PC-DIMM, ensures
that the memory slot is available and that addresses don't overlap
with existing memory regions. The corresponding DRCs in the LMB
and PMEM namespaces are thus necessarily attachable at plug time.
Pass &error_abort to spapr_drc_attach() in spapr_add_lmbs() and
spapr_add_nvdimm(). This allows to greatly simplify error handling
on the plug path.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120234208.683521-3-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PHB acts as the hotplug handler for PCI devices. It does some
sanity checks on DR enablement, PCI bridge chassis numbers and
multifunction. These checks are currently performed at plug time,
but they would best sit in a pre-plug handler in order to error
out as early as possible.
Create a spapr_pci_pre_plug() handler and move all the checking
there. Add a check that the associated DRC doesn't already have
an attached device. This is equivalent to the slot availability
check performed by do_pci_register_device() upon realization of
the PCI device.
This allows to pass &error_abort to spapr_drc_attach() and to end
up with a plug handler that doesn't need to report errors anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120234208.683521-2-groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Never used from the start.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120174646.619395-6-groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR XIVE device is created by the machine in spapr_irq_init().
The latter overrides any value provided by the user with -global for
the "nr-irqs" and "nr-ends" properties with strictly positive values.
It seems reasonable to assume these properties should never be 0,
which wouldn't make much sense by the way.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120174646.619395-2-groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PTC field has 8 bits, PVPE has 4. We plan to use the
"hw/registerfields.h" API with MIPS CPU definitions
(target/mips/cpu.h). Meanwhile we use magic 8 and 4.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201204222622.2743175-6-f4bug@amsat.org>
Do not initialize MT-related config register if the MT ASE
is not present.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201204222622.2743175-5-f4bug@amsat.org>
Instead of accessing CP0_Config3 directly and checking
the 'Multi-Threading Present' bit, introduce an helper
to simplify code review.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201204222622.2743175-3-f4bug@amsat.org>
Address translation is an architectural thing (not hardware
related). Move the helpers from hw/ to target/.
As physical address and KVM are specific to system mode
emulation, restrict this file to softmmu, so it doesn't
get compiled for user-mode emulation.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201206233949.3783184-2-f4bug@amsat.org>
As cpu_supports_isa() / cpu_supports_cps_smp() take a 'cpu_type'
name argument, rename them cpu_type_supports_FEAT().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201207215257.4004222-2-f4bug@amsat.org>
ads7846 is a touch-screen controller that is an input device rather
than a display device, so move it to the hw/input folder.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201115123503.1110665-1-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
While this change helps triskaidekaphobic developers, it
is a good practice to avoid magic values and using constant
definitions instead.
Introduce the PAM_REGIONS_COUNT and use it. No logical change.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Julia Suvorova <jusual@redhat.com>
Message-Id: <20201202132038.1276404-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Fix code style. Don't use '#' flag of printf format ('%#') in
format strings, use '0x' prefix instead
Signed-off-by: Xinhao Zhang <zhangxinhao1@huawei.com>
Signed-off-by: Kai Deng <dengkai1@huawei.com>
Message-Id: <20201104133709.3326630-1-zhangxinhao1@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The handling of the GLUE (General Logic Unit) device is
currently open-coded. Make this into a proper QOM device.
This minor piece of modernisation gets rid of the free
floating qemu_irq array 'pic', which Coverity points out
is technically leaked when we exit the machine init function.
(The replacement glue device is not leaked because it gets
added to the sysbus, so it's accessible via that.)
Fixes: Coverity CID 1421883
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201106235109.7066-3-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The q800 board code connects both of the IRQ outputs of the ESCC
to the same pic[3] qemu_irq. Connecting two qemu_irqs outputs directly
to the same input is not valid as it produces subtly wrong behaviour
(for instance if both the IRQ lines are high, and then one goes
low, the PIC input will see this as a high-to-low transition
even though the second IRQ line should still be holding it high).
This kind of wiring needs an explicitly created OR gate; add one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20201106235109.7066-2-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Neither sysbus.h nor module.h are required to compile this file.
diag288 is not a sysbus device, and module.h (for type_init) is
included eventually through qom/object.h.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20201118090344.243117-1-thuth@redhat.com>
[CH: tweaked description]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
serial_hd(i) is NULL if and only if i >= serial_max_hds(). Test
serial_hd(i) instead of bounding the loop at serial_max_hds(),
thus removing one more function that vl.c is expected to export.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move CHECKPOINT_INIT right before the machine initialization is
completed. Everything before is essentially an extension of
command line parsing.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some very simple initialization routines can be nested in existing
subsystem-level functions, do that to simplify qemu_init.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Once smp_parse is done, the validation operates on the MachineState.
There is no reason for that code to be in vl.c.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 5ec3a23e6c ("serial: convert PIO to new memory
api read/write") we don't need to worry about accesses bigger
than 8-bit. Use the extract()/deposit() functions to access
the correct part of the 16-bit 'divider' register.
Reported-by: Jonathan D. Belanger <jbelanger1@rochester.rr.com>
Buglink: https://bugs.launchpad.net/qemu/+bug/1904331
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201120161933.2514089-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the machine properties or loader parameters instead.
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the machine properties instead.
Cc: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull defaults to digic4_board_init so that a MachineState is available.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201026143028.3034018-15-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201026143028.3034018-14-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201026143028.3034018-13-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ROM loader state is global and not part of the MCU, and the
BIOS is in machine->firmware. So just like the kernel case,
load it in the board.
Due to the ordering between CPU reset and ROM reset, the ROM
has to be registered before the CPU is realized, otherwise
the reset vector is loaded before the ROM is there.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-11-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-10-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-9-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-7-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-6-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201026143028.3034018-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Get the firmware name from the MachineState object.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-4-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201026143028.3034018-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename 'slave stream'
as 'sink stream'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200910070131.435543-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename 'slave stream'
as 'sink stream'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200910070131.435543-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename 'slave stream'
as 'sink stream'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200910070131.435543-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename max_slaves
as max_peripherals.
Patch generated using:
$ sed -i s/slave/peripheral/ \
hw/ssi/aspeed_smc.c include/hw/ssi/aspeed_smc.h
One line in aspeed_smc_read() has been manually tweaked
to pass checkpatch.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201012124955.3409127-2-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds support the kernel-irqchip option for
WHPX with on or off value. 'split' value is not supported
for the option. The option only works for the latest version
of Windows (ones that are coming out on Insiders). The
change maintains backward compatibility on older version of
Windows where this option is not supported.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Message-Id: <SN4PR2101MB0880B13258DA9251F8459F4DC0170@SN4PR2101MB0880.namprd21.prod.outlook.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The IOAPIC has an 'Extended Destination ID' field in its RTE, which maps
to bits 11-4 of the MSI address. Since those address bits fall within a
given 4KiB page they were historically non-trivial to use on real hardware.
The Intel IOMMU uses the lowest bit to indicate a remappable format MSI,
and then the remaining 7 bits are part of the index.
Where the remappable format bit isn't set, we can actually use the other
seven to allow external (IOAPIC and MSI) interrupts to reach up to 32768
CPUs instead of just the 255 permitted on bare metal.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <78097f9218300e63e751e077a0a5ca029b56ba46.camel@infradead.org>
[Fix UBSAN warning. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Change to "expects a THING" where that's an obvious improvement
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201113082626.2725812-11-armbru@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
contrib/plugins/hotblocks.c
contrib/plugins/hotpages.c
contrib/plugins/howvec.c
contrib/plugins/lockstep.c
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/fp/platform.h
tests/migration/s390x/a-b-bios.c
tests/plugin/bb.c
tests/plugin/empty.c
tests/plugin/insn.c
tests/plugin/mem.c
tests/test-rcu-simpleq.c
tests/test-rcu-slist.c
tests/test-rcu-tailq.c
tests/uefi-test-tools/UefiTestToolsPkg/BiosTablesTest/BiosTablesTest.c
contrib/plugins/, tests/plugin/, and tests/test-rcu-slist.c appear not
to include osdep.h intentionally. The remaining reverts are the same
as in commit bbfff19688.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201113061216.2483385-1-armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAl/SDVIACgkQUaNDx8/7
7KFF3BAAvYPgi/XJN0caP0qbxZy7GvBA1nmINQq910d1ARz04Vin8K6oj9x02taq
1MMhk9KryNRF1VuT98eya8u9htsg1OxrosqSAwjrtI72oSRWLGSl1Ww0sKIPcBET
OUq8pfAv+gW5lVWRkpnEA4Ly33PMTp5zfT3sy0riuSf+Z7Mg/8Lk28tNSOYu6hBl
LUZddcweMshishrJ46F1SSwWFfdZ2+5Y1eLSDRGwn8Ba5xy6SI3UDQVFze1vFmo3
h1Sd9s2tVJtJn4It2op41XKQX99uoGUy98CYVrbAd/1euZIm/6c4ju9upZiFUU/p
wm8I1njd5ybdPzRmJkJ8zQxsblgvw/Ua0YLmX/4aFsPUlKPyomOr++YMXcyrThEY
cxezJsSmj5f/oVaGRULbRVR8hhaM18RLBgwQAbfNSOTylmFa+URT6FLR4mnysfhz
zv76xt6S8BIS8CAgxqB13tj4tQPXUansQsuVTWwRwE8mHd5Vkhau2oOQR5n9cV+n
FNjvmqUN7ICtekmwMmBdNOI4yiGBY1ckcj/UoCzkuAYK444kzTqFfB4CZABNhs5f
/fjAsWAvYtqsLFUWCUnpHkxyq/8N0hpSZc0DI3FDPsup4/NlRG17p+DcrNqimwIE
SZ1I28YYdmoh1igMQK46x7UvvnceCCXkHAnR+nGix8jOpSCWLKs=
=abAb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20201210' into staging
Aspeed patches :
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
# gpg: Signature made Thu 10 Dec 2020 11:58:10 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20201210:
aspeed: g220a-bmc: Add an FRU
aspeed/smc: Add support for address lane disablement
ast2600: SRAM is 89KB
aspeed: Add support for the g220a-bmc board
hw/misc: add an EMC141{3,4} device model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct a typo in the name we give the NVIC object.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-28-peter.maydell@linaro.org
The RAS feature has a block of memory-mapped registers at offset
0x5000 within the PPB. For a "minimal RAS" implementation we provide
no error records and so the only registers that exist in the block
are ERRIIDR and ERRDEVID.
The "RAZ/WI for privileged, BusFault for nonprivileged" behaviour
of the "nvic-default" region is actually valid for minimal-RAS,
so the main benefit of providing an explicit implementation of
the register block is more accurate LOG_UNIMP messages, and a
framework for where we could add a real RAS implementation later
if necessary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-27-peter.maydell@linaro.org
For v8.1M the architecture mandates that CPUs must provide at
least the "minimal RAS implementation" from the Reliability,
Availability and Serviceability extension. This consists of:
* an ESB instruction which is a NOP
-- since it is in the HINT space we need only add a comment
* an RFSR register which will RAZ/WI
* a RAZ/WI AIRCR.IESB bit
-- the code which handles writes to AIRCR does not allow setting
of RES0 bits, so we already treat this as RAZ/WI; add a comment
noting that this is deliberate
* minimal implementation of the RAS register block at 0xe0005000
-- this will be in a subsequent commit
* setting the ID_PFR0.RAS field to 0b0010
-- we will do this when we add the Cortex-M55 CPU model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-26-peter.maydell@linaro.org
In commit 077d744910 we added code to handle the v8M
requirement that returns from NMI or HardFault forcibly deactivate
those exceptions regardless of what interrupt the guest is trying to
deactivate. Unfortunately this broke the handling of the "illegal
exception return because the returning exception number is not
active" check for those cases. In the pseudocode this test is done
on the exception the guest asks to return from, but because our
implementation was doing this in armv7m_nvic_complete_irq() after the
new "deactivate NMI/HardFault regardless" code we ended up doing the
test on the VecInfo for that exception instead, which usually meant
failing to raise the illegal exception return fault.
In the case for "configurable exception targeting the opposite
security state" we detected the illegal-return case but went ahead
and deactivated the VecInfo anyway, which is wrong because that is
the VecInfo for the other security state.
Rearrange the code so that we first identify the illegal return
cases, then see if we really need to deactivate NMI or HardFault
instead, and finally do the deactivation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-25-peter.maydell@linaro.org
v8.1M introduces a new TRD flag in the CCR register, which enables
checking for stack frame integrity signatures on SG instructions.
This bit is not banked, and is always RAZ/WI to Non-secure code.
Adjust the code for handling CCR reads and writes to handle this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-23-peter.maydell@linaro.org
In v8.1M a REVIDR register is defined, which is at address 0xe00ecfc
and is a read-only IMPDEF register providing implementation specific
minor revision information, like the v8A REVIDR_EL1. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-19-peter.maydell@linaro.org
The FPDSCR register has a similar layout to the FPSCR. In v8.1M it
gains new fields FZ16 (if half-precision floating point is supported)
and LTPSIZE (always reads as 4). Update the reset value and the code
that handles writes to this register accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-16-peter.maydell@linaro.org
For M-profile CPUs, the range from 0xe0000000 to 0xe00fffff is the
Private Peripheral Bus range, which includes all of the memory mapped
devices and registers that are part of the CPU itself, including the
NVIC, systick timer, and debug and trace components like the Data
Watchpoint and Trace unit (DWT). Within this large region, the range
0xe000e000 to 0xe000efff is the System Control Space (NVIC, system
registers, systick) and 0xe002e000 to 0exe002efff is its Non-secure
alias.
The architecture is clear that within the SCS unimplemented registers
should be RES0 for privileged accesses and generate BusFault for
unprivileged accesses, and we currently implement this.
It is less clear about how to handle accesses to unimplemented
regions of the wider PPB. Unprivileged accesses should definitely
cause BusFaults (R_DQQS), but the behaviour of privileged accesses is
not given as a general rule. However, the register definitions of
individual registers for components like the DWT all state that they
are RES0 if the relevant component is not implemented, so the
simplest way to provide that is to provide RAZ/WI for the whole range
for privileged accesses. (The v7M Arm ARM does say that reserved
registers should be UNK/SBZP.)
Expand the container MemoryRegion that the NVIC exposes so that
it covers the whole PPB space. This means:
* moving the address that the ARMV7M device maps it to down by
0xe000 bytes
* moving the off and the offsets within the container of all the
subregions forward by 0xe000 bytes
* adding a new default MemoryRegion that covers the whole container
at a lower priority than anything else and which provides the
RAZWI/BusFault behaviour
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-2-peter.maydell@linaro.org
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-5-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-4-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-3-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201126111109.112238-2-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Trusted Firmware now supports A72 on sbsa-ref by default [1] so enable
it for QEMU as well. A53 was already enabled there.
1. https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7117
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201120141705.246690-1-marcin.juszkiewicz@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect CAN0 and CAN1 on the ZynqMP.
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-3-git-send-email-fnu.vikram@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xilinx ZynqMP CAN controller is developed based on SocketCAN, QEMU CAN bus
implementation. Bus connection and socketCAN connection for each CAN module
can be set through command lines.
Example for using single CAN:
-object can-bus,id=canbus0 \
-machine xlnx-zcu102.canbus0=canbus0 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0
Example for connecting both CAN to same virtual CAN on host machine:
-object can-bus,id=canbus0 -object can-bus,id=canbus1 \
-machine xlnx-zcu102.canbus0=canbus0 \
-machine xlnx-zcu102.canbus1=canbus1 \
-object can-host-socketcan,id=socketcan0,if=vcan0,canbus=canbus0 \
-object can-host-socketcan,id=socketcan1,if=vcan0,canbus=canbus1
To create virtual CAN on the host machine, please check the QEMU CAN docs:
https://github.com/qemu/qemu/blob/master/docs/can.txt
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-2-git-send-email-fnu.vikram@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Accroding to the SMMUv3 spec, the SPAN field of Level1 Stream Table
Descriptor is 5 bits([4:0]).
Fixes: 9bde7f0674f(hw/arm/smmuv3: Implement translate callback)
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Message-id: 20201124023711.1184-1-jiangkunkun@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an eeprom device and fill it with fru
information
$ ipmitool fru print 0
Product Manufacturer : Bytedance
Product Name : G220A
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201210103607.556-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The controller can be configured to disable or enable address and data
byte lanes when issuing commands. This is useful in read command mode
to send SPI NOR commands that don't have an address space, such as
RDID. It's a good way to have a unified read operation for registers
and flash contents accesses.
A new SPI driver proposed by Aspeed makes use of this feature. Add
support for address lanes to start with. We will do the same for the
data lanes if they are controlled one day.
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20201120161547.740806-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On the AST2600A1, the SRAM size was increased to 89KB.
Fixes: 7582591ae7 ("aspeed: Support AST2600A1 silicon revision")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201112012113.835858-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
G220A is a 2 socket x86 motherboard supported by OpenBMC.
Strapping configuration was obtained from hardware.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20201122105134.671-2-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Largely inspired by the TMP421 temperature sensor, here is a model for
the EMC1413/EMC1414 temperature sensors.
Specs can be found here :
http://ww1.microchip.com/downloads/en/DeviceDoc/20005274A.pdf
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201122105134.671-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Create second ioapic, route virtio-mmio IRQs to it,
allow more virtio-mmio devices (24 instead of 8).
Needs ACPI, enabled by default, can be turned off
using -machine ioapic2=off
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-8-kraxel@redhat.com
With the improved gsi_handler() we don't need
our private version any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-7-kraxel@redhat.com
Allows to move them in case we have enough
irq lines available.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-6-kraxel@redhat.com
This will allow to increase the number of transports in
case we have enough irq lines available for them all.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-5-kraxel@redhat.com
Add ioapic_init_secondary to initialize it, wire up
in gsi handling and acpi apic table creation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-4-kraxel@redhat.com
Rewrite function to use switch() for IRQ number mapping.
Check i8259_irq exists before raising it so the function
also works in case no i8259 (aka pic) is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20201203105423.10431-3-kraxel@redhat.com
Added AER capability for virtio-pci devices.
Also added property for devices, by default AER is disabled.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20201203110713.204938-3-andrew@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Removed hardcoded offset for ats. Added cap offset counter
for future capabilities like AER.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20201203110713.204938-2-andrew@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Keep CPU hotunplug with SMI disabled on 5.2 and older and enable
it by default on newer machine types.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be reused by next patch to check validity of unplug
feature.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
if firmware and QEMU negotiated CPU hotunplug support, generate
_EJ0 method so that it will mark CPU for removal by firmware and
pass control to it by triggering SMI.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Adds bit #4 to status/control field of CPU hotplug MMIO interface.
New bit will be used OSPM to mark CPUs as pending for removal by firmware,
when it calls _EJ0 method on CPU device node. Later on, when firmware
sees this bit set, it will perform CPU eject which will clear bit #4
as well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At Hewlett Packard Inc. we have a need for increased fw size to enable testing of our custom fw.
Rebase v6 patch to d73c46e4
Signed-off-by: Erich McMillan <erich.mcmillan@hp.com>
Message-Id: <20201208155338.14-1-erich.mcmillan@hp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Coverity points out that the realize function for the TYPE_MCF5206_MBAR
device leaks the IRQ array it allocates with qemu_allocate_irqs().
Keep a pointer to it in the device state struct to avoid the leak.
(Since it needs to stay around for the life of the simulation there
is no need to actually free it, and the leak was harmless.)
Fixes: Coverity CID 1432412
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201120172314.14725-1-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add 6.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201109173928.1001764-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only three uses remained, and we can remove them on that case.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-28-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate device just once.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-27-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pass it as an argument.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-26-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-25-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
So we can calculate the device id when we need it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-24-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It can never give one error.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-23-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We check that it exist at device creation time, so we don't have to
check anywhere else.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-22-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit:
* Rename them to failover_find_primary_devices() so
- it starts with failover_
- it don't connect anything, just find the primary device
* Create documentation for the function
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-19-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It just calls virtio_net_find_primary(), so just update the callers.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-18-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use pasive.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-17-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We didn't use at all the -1 value, and we don't really care. It was
only used for the cases when this is not the device that we are
searching for. And in that case we should not hide the device.
Once there, simplify virtio-Snet_primary_should_be_hidden.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-16-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
a - is_my_primary() never sets one error
b - If we return 1, primary_device_id is always set
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-15-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Two things, at this point:
* n->primary_device_id has to be set, otherwise
virtio_net_find_primary don't work. So we have a leak here.
* it has to be exactly the same that prim_dev->id because what
qdev_find_recursive() does is just compare this two values.
So remove the unneeded assignment and leaky bits.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-14-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was only used once. And we have there opts->id, so no need for it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-13-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can calculate it, and we only use it once anyways.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-12-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was really only used once, in failover_add_primary(). Just search
for it on global opts when it is needed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-11-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-10-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
You should not use passive naming variables.
And once there, be able to search for them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-9-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Never both.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-8-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It was only set "once", and with the wrong value. As far as I can see,
libvirt still don't use it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-7-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-6-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Just remove the struct member.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-5-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-4-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Once there, remove not needed cast.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20201118083748.1328-3-quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If table size is changed between virt_acpi_build and
virt_acpi_build_update, the table size would not be updated to
UEFI, therefore, just align the size to 128kb, which is enough
and same with x86. It would warn if 64k is not enough and the
align size should be updated.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-7-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resources of pxbs are obtained by crs_build and the resources
used by pxbs would be moved from the resources defined for host-bridge.
The resources for pxb are composed of following two parts:
1. The bar space of the pci-bridge/pcie-root-port behined it
2. The config space of devices behind it.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-6-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract crs build form acpi_build.c, the function could also be used
to build the crs for pxbs for arm. The resources are composed by two parts:
1. The bar space of pci-bridge/pcie-root-ports
2. The resources needed by devices behind PXBs.
The base and limit of memory/io are obtained from the config via two APIs:
pci_bridge_get_base and pci_bridge_get_limit
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-5-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add bus property to virt machine for primary PCI root bus and use it to add
extra pci roots behind it.
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Message-Id: <20201119014841.7298-4-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract extra pci roots addition from pc machine, which could be used by
other machines.
In order to make uefi get the extra roots, it is necessary to write extra
roots into fw_cfg. And only if the uefi knows there are extra roots,
the config spaces of devices behind the root could be obtained.
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Message-Id: <20201119014841.7298-3-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract two APIs acpi_dsdt_add_pci_route_table and
acpi_dsdt_add_pci_osc from acpi_dsdt_add_pci. The first
API is used to specify the pci route table and the second
API is used to declare the operation system capabilities.
These two APIs would be used to specify the pxb-pcie in DSDT.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-2-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If we find a queue with an inconsistent guest index value, explicitly mark the
device as needing a reset - and broken - via virtio_error().
There's at least one driver implementation - the virtio-win NetKVM driver - that
is able to handle a VIRTIO_CONFIG_S_NEEDS_RESET notification and successfully
restore the device to a working state. Other implementations do not correctly
handle this, but as the VQ is not in a functional state anyway, this is still
worth doing.
Signed-off-by: John Levon <john.levon@nutanix.com>
Message-Id: <20201120185103.GA442386@sent>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although they didn't reach the notifier because of the filtering in
memory_region_notify_iommu_one, the vt-d was still splitting huge
memory invalidations in chunks. Skipping it.
This improves performance in case of netperf with vhost-net:
* TCP_STREAM: From 1923.6Mbit/s to 2175.13Mbit/s (13%)
* TCP_RR: From 8464.73 trans/s to 8932.703333 trans/s (5.5%)
* UDP_RR: From 8562.08 trans/s to 9005.62/s (5.1%)
* UDP_STREAM: No change observed (insignificant 0.1% improvement)
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-5-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows us to differentiate between regular IOMMU map/unmap events
and DEVIOTLB unmap. Doing so, notifiers that only need device IOTLB
invalidations will not receive regular IOMMU unmappings.
Adapt intel and vhost to use it.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-4-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This way we can tell between regular IOMMUTLBEntry (entry of IOMMU
hardware) and notifications.
In the notifications, we set explicitly if it is a MAPs or an UNMAP,
instead of trusting in entry permissions to differentiate them.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Previous name didn't reflect the iommu operation.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A case was reported where s->io_buffer_index can be out of range.
The report skimped on the details but it seems to be triggered
by s->lba == -1 on the READ/READ CD paths (e.g. by sending an
ATAPI command with LBA = 0xFFFFFFFF). For now paper over it
with assertions. The first one ensures that there is no overflow
when incrementing s->io_buffer_index, the second checks for the
buffer overrun.
Note that the buffer overrun is only a read, so I am not sure
if the assertion failure is actually less harmful than the overrun.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20201201120926.56559-1-pbonzini@redhat.com
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An integer underflow could occur during packet transmission due to 'tx_len' not
being updated if SONIC_TFC register is set to zero. Check for negative 'tx_len'
when removing existing FCS.
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1899722
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-id: 20201124092445.658647-1-mcascell@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit bccb20c49d as it
introduced a regression blocking bus addresses > 0x1f or higher.
Legal bus numbers go up to 0xff.
Fixes: bccb20c49d ("Use qemu_strtoul() in set_pci_host_devaddr()")
Reported-by: Klaus Herman <kherman@inbox.lv>
Reported-by: Geoffrey McRae <geoff@hostfission.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: "Philippe Mathieu-Daudé" <philmd@redhat.com>
Message-Id: <20201120130409.956956-1-mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
While receiving packets via e1000e_write_packet_to_guest() routine,
'desc_offset' is advanced only when RX descriptor is processed. And
RX descriptor is not processed if it has NULL buffer address.
This may lead to an infinite loop condition. Increament 'desc_offset'
to process next descriptor in the ring to avoid infinite loop.
Reported-by: Cheol-woo Myung <330cjfdn@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
By default dirty pages tracking is enabled during iterative phase
(pre-copy phase).
Added per device opt-out option 'x-pre-copy-dirty-page-tracking' to
disable dirty pages tracking during iterative phase. If the option
'x-pre-copy-dirty-page-tracking=off' is set for any VFIO device, dirty
pages tracking during iterative phase will be disabled.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Support for migration of vfio devices is still in flux. Developers
are attempting to add support for new devices and new architectures,
but none are yet readily available for validation. We have concerns
whether we're transferring device resources at the right point in the
migration, whether we're guaranteeing that updates during pre-copy are
migrated, and whether we can provide bit-stream compatibility should
any of this change. Even the question of whether devices should
participate in dirty page tracking during pre-copy seems contentious.
In short, migration support has not had enough soak time and it feels
premature to mark it as supported.
Create an experimental option such that we can continue to develop.
[Retaining previous acks/reviews for a previously identical code
change with different specifics in the commit log.]
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When 'j = icu->nr_sense – 1', the 'j < icu->nr_sense' condition is true,
then 'j = icu->nr_sense', the'icu->init_sense[j]' has out-of-bounds access.
The asan showed stack:
ERROR: AddressSanitizer: heap-buffer-overflow on address 0x604000004d7d at pc 0x55852cd26a76 bp 0x7ffe39f26200 sp 0x7ffe39f261f0
READ of size 1 at 0x604000004d7d thread T0
#0 0x55852cd26a75 in rxicu_realize ../hw/intc/rx_icu.c:311
#1 0x55852cf075f7 in device_set_realized ../hw/core/qdev.c:886
#2 0x55852cd4a32f in property_set_bool ../qom/object.c:2251
#3 0x55852cd4f9bb in object_property_set ../qom/object.c:1398
#4 0x55852cd54f3f in object_property_set_qobject ../qom/qom-qobject.c:28
#5 0x55852cd4fc3f in object_property_set_bool ../qom/object.c:1465
#6 0x55852cbf0b27 in register_icu ../hw/rx/rx62n.c:156
#7 0x55852cbf12a6 in rx62n_realize ../hw/rx/rx62n.c:261
#8 0x55852cf075f7 in device_set_realized ../hw/core/qdev.c:886
#9 0x55852cd4a32f in property_set_bool ../qom/object.c:2251
#10 0x55852cd4f9bb in object_property_set ../qom/object.c:1398
#11 0x55852cd54f3f in object_property_set_qobject ../qom/qom-qobject.c:28
#12 0x55852cd4fc3f in object_property_set_bool ../qom/object.c:1465
#13 0x55852cbf1a85 in rx_gdbsim_init ../hw/rx/rx-gdbsim.c:109
#14 0x55852cd22de0 in qemu_init ../softmmu/vl.c:4380
#15 0x55852ca57088 in main ../softmmu/main.c:49
#16 0x7feefafa5d42 in __libc_start_main (/lib64/libc.so.6+0x26d42)
Add the 'ice->src[i].sense' initialize to the default value, and then
process init_sense array to identify which irqs should be level-triggered.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201111141733.2358800-1-kuhn.chenqun@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%i" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 5F9FD78B.8000300@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit ae5643ecc6 "hw/display/tcx: Allow 64-bit accesses to framebuffer stippler
and blitter" enabled 64-bit access for the TCX framebuffer stippler and blitter
but missed applying the change to one of the blitter MemoryRegions.
Whilst the original change works for me on my local NetBSD test image, the latest
NetBSD ISO panics on startup without this fix.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: ae5643ecc6 ("hw/display/tcx: Allow 64-bit accesses to framebuffer stippler and blitter")
Buglink: https://bugs.launchpad.net/bugs/1892540
Message-Id: <20201120081754.18250-1-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Remove the "default y" for USB_XHCI_SYSBUS because
sysbus devices are not user creatable; boards that use them will
specify them manually with "imply" or "select" clauses.
It would be nice to keep the ability to remove PCIe and USB from microvm,
since thos can be disabled on the command line and therefore should not
be included if QEMU is configured --without-default-devices. However
it's too late for 5.2 to figure out a place for the DSDT creation code.
Reported-by: Bruce Rogers <brogers@suse.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The zPCI group and function structures are big endian. However, we do
not consistently store them as big endian locally, and are missing some
conversions.
Let's just store the structures as host endian instead and convert to
big endian when actually handling the instructions retrieving the data.
Also fix the layout of ClpReqQueryPciGrp: g is actually only 8 bit. This
also fixes accesses on little endian hosts, and makes accesses on big
endian hosts consistent.
Fixes: 28dc86a072 ("s390x/pci: use a PCI Group structure")
Fixes: 9670ee7527 ("s390x/pci: use a PCI Function structure")
Fixes: 1e7552ff5c ("s390x/pci: get zPCI function info from host")
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201118104202.1301363-1-cohuck@redhat.com>
Hot-unplugging a vfio-pci device on s390x causes a QEMU crash:
qemu-system-s390x: ../softmmu/memory.c:2772:
do_address_space_destroy: Assertion `QTAILQ_EMPTY(&as->listeners)' failed.
In s390, the IOMMU address space is freed during device unplug but the
associated vfio-pci device may not yet be finalized and therefore may
still have a listener registered to the IOMMU address space.
Commit a2166410ad ("spapr_pci: Unregister listeners before destroying
the IOMMU address space") previously resolved this issue for spapr_pci.
We are now seeing this in s390x; it would seem the possibility for this
issue was already present but based on a bisect commit 2d24a64661
("device-core: use RCU for list of children of a bus") has now changed
the timing such that it is now readily reproducible.
Add logic to ensure listeners are removed before destroying the address
space.
Reported-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1605562955-21152-1-git-send-email-mjrosato@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The Control Program Name Code (CPNC) portion of the diag318
info must be set within the SIE block of each VCPU in the
configuration. The handler will iterate through each VCPU
and dirty the diag318_info reg to be synced with KVM on a
subsequent sync_regs call.
Additionally, the diag318 info resets must be handled via
userspace. As such, QEMU will reset this value for each
VCPU during a modified clear, load normal, and load clear
reset event.
Fixes: fabdada935 ("s390: guest support for diagnose 0x318")
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Message-Id: <20201113221022.257054-1-walling@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This fixes a regression that badly breaks some guest setups because
IPIs end up misconfigured in the XIVE interrupt controller. Hopefully,
the last fix for sPAPR. I'm sending this PR with the blessing of David
who is currently on holidays.
-----BEGIN PGP SIGNATURE-----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=zUP3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/ppc-for-5.2-20201118' into staging
ppc patch queue for 2020-11-18
This fixes a regression that badly breaks some guest setups because
IPIs end up misconfigured in the XIVE interrupt controller. Hopefully,
the last fix for sPAPR. I'm sending this PR with the blessing of David
who is currently on holidays.
# gpg: Signature made Wed 18 Nov 2020 10:26:31 GMT
# gpg: using RSA key B4828BAF943140CEF2A3491071D4D5E5822F73D6
# gpg: Good signature from "Greg Kurz <groug@kaod.org>" [full]
# gpg: aka "Gregory Kurz <gregory.kurz@free.fr>" [full]
# gpg: aka "[jpeg image of size 3330]" [full]
# Primary key fingerprint: B482 8BAF 9431 40CE F2A3 4910 71D4 D5E5 822F 73D6
* remotes/gkurz/tags/ppc-for-5.2-20201118:
Revert series "spapr/xive: Allocate vCPU IPIs from the vCPU contexts"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This series was largely built on the assumption that IPI numbers are
numerically equal to vCPU ids. Even if this happens to be the case
in practice with the default machine settings, this ceases to be true
if VSMT is set to a different value than the number of vCPUs per core.
This causes bogus IPI numbers to be created in KVM from a guest stand
point. This leads to unknow results in the guest, including crashes
or missing vCPUs (see BugLink) and even non-fatal oopses in current
KVM that lacks a check before accessing misconfigured HW (see [1]).
A tentative patch was sent (see [2]) but it seems too complex to be
merged in an RC. Since the original changes are essentially an
optimization, it seems safer to revert them for now. The damage is
done by commit acbdb9956f ("spapr/xive: Allocate IPIs independently
from the other sources") but the previous patches in the series are
really preparatory patches. So this reverts the whole series:
eab0a2d06e ("spapr/xive: Allocate vCPU IPIs from the vCPU contexts")
acbdb9956f ("spapr/xive: Allocate IPIs independently from the other sources")
fa94447a2c ("spapr/xive: Use kvmppc_xive_source_reset() in post_load")
235d3b1162 ("spapr/xive: Modify kvm_cpu_is_enabled() interface")
[1] https://marc.info/?l=kvm-ppc&m=160458409722959&w=4
[2] https://lists.gnu.org/archive/html/qemu-devel/2020-11/msg03626.html
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Fixes: acbdb9956f ("spapr/xive: Allocate IPIs independently from the other sources")
BugLink: https://bugs.launchpad.net/qemu/+bug/1900241
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <160554086275.1325084.12110142252189044646.stgit@bahia.lan>
Fix also a similar typo in a code comment.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <20201117193448.393472-1-sw@weilnetz.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Update NetBSD VM to version 9.1
* Misc fixes (e.g. categorize some devices)
-----BEGIN PGP SIGNATURE-----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=A3/B
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-11-17' into staging
* Fixes for compiling on Haiku, and add Haiku VM for compile-testing
* Update NetBSD VM to version 9.1
* Misc fixes (e.g. categorize some devices)
# gpg: Signature made Tue 17 Nov 2020 09:20:31 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-11-17:
max111x: put it into the 'misc' category
nand: put it into the 'storage' category
ads7846: put it into the 'input' category
ssd0323: put it into the 'display' category
gitlab-ci: Use $CI_REGISTRY instead of hard-coding registry.gitlab.com
target/microblaze: Fix possible array out of bounds in mmu_write()
tests/vm: update NetBSD to 9.1
tests/vm: Add Haiku test based on their vagrant images
configure: Add a proper check for sys/ioccom.h and use it in tpm_ioctl.h
configure: Do not build pc-bios/optionrom on Haiku
configure: Fix the _BSD_SOURCE define for the Haiku build
qemu/bswap: Remove unused qemu_bswap_len()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TMP105 datasheet says that in Interrupt Mode (when TM==1) the device
signals an alert when the temperature equals or exceeds the T_high value and
then remains high until a device register is read or the device responds to
the SMBUS Alert Response address, or the device is put into Shutdown Mode.
Thereafter the Alert pin will only be re-signalled when temperature falls
below T_low; alert can then be cleared in the same set of ways, and the
device returns to its initial "alert when temperature goes above T_high"
mode. (If this textual description is confusing, see figure 3 in the
TI datasheet at https://www.ti.com/lit/gpn/tmp105 .)
We were misimplementing this as a simple "always alert if temperature is
above T_high or below T_low" condition, which gives a spurious alert on
startup if using the "T_high = 80 degrees C, T_low = 75 degrees C" reset
limit values.
Implement the correct (hysteresis) behaviour by tracking whether we
are currently looking for the temperature to rise over T_high or
for it to fall below T_low. Our implementation of the comparator
mode (TM==0) wasn't wrong, but rephrase it to match the way that
interrupt mode is now handled for clarity.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-3-peter.maydell@linaro.org
The TMP105 datasheet (https://www.ti.com/lit/gpn/tmp105) says that the
power-up reset values for the T_low and T_high registers are 80 degrees C
and 75 degrees C, which are 0x500 and 0x4B0 hex according to table 5. These
values are then shifted right by four bits to give the register reset
values, since both registers store the 12 bits of temperature data in bits
[15..4] of a 16 bit register.
We were resetting these registers to zero, which is problematic for Linux
guests which enable the alert interrupt and then immediately take an
unexpected overtemperature alert because the current temperature is above
freezing...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-2-peter.maydell@linaro.org
This patch fixes CID 1432800 by removing an unnecessary check.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 5edab03d40 we added tracepoints to the ps2 keyboard
and mouse emulation. However we didn't remove all the debug-by-printf
support. In fact there is only one printf() remaining, and it is
redundant with the trace_ps2_write_mouse() event next to it.
Remove the printf() and the now-unused DEBUG* macros.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20201101133258.4240-1-peter.maydell@linaro.org
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 20201111073651.72804-1-alex.chen@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The removal of the selection of A15MPCORE from ARM_VIRT also
removed what A15MPCORE selects, ARM_GIC. We still need ARM_GIC.
Fixes: bec3c97e0c ("hw/arm/virt: Remove dependency on Cortex-A15 MPCore peripherals")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201111143440.112763-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the SD spec, to indicate a 2 GiB card, BLOCK_LEN shall be 1024
bytes, hence the READ_BL_LEN field in the CSD register shall be 10
instead of 9.
This fixes the acceptance test error for the NetBSD 9.0 test of the
Orange Pi PC that has an expanded SD card image of 2 GiB size.
Fixes: 6d2d4069c4 ("hw/sd: Correct the maximum size of a Standard Capacity SD Memory Card")
Reported-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-Id: <20201025152357.11865-1-bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The category of the max111x device is not set, put it into the 'misc'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201112125824.763182-5-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The category of the nand device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201112125824.763182-4-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The category of the ads7846 device is not set, put it into the 'input'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201112125824.763182-3-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The category of the ssd0323 device is not set, put it into the 'display'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201112125824.763182-2-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Linux has some OS-specific (and sometimes weird) mappings for various SCSI
statuses and sense codes. The most important is probably RESERVATION
CONFLICT. Add them so that they can be reported back to the guest
kernel.
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----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=GI5d
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-11-15' into staging
Fix Lesser GPL license versions (should be "2.1" and not "2")
# gpg: Signature made Sun 15 Nov 2020 16:20:10 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-11-15: (26 commits)
nomaintainer: Fix Lesser GPL version number
test: Fix LGPL information in the file headers
tests/acceptance: Fix LGPL information in the file headers
tests/migration: Fix LGPL information in the file headers
sparc tcg cpus: Fix Lesser GPL version number
e1000e: Fix Lesser GPL version number
x86 hvf cpus: Fix Lesser GPL version number
nvdimm: Fix Lesser GPL version number
w32: Fix Lesser GPL version number
tpm: Fix Lesser GPL version number
overall/alpha tcg cpus|hppa: Fix Lesser GPL version number
overall usermode...: Fix Lesser GPL version number
migration: Fix Lesser GPL version number
parallel nor flash: Fix Lesser GPL version number
arm tcg cpus: Fix Lesser GPL version number
x86 tcg cpus: Fix Lesser GPL version number
linux user: Fix Lesser GPL version number
usb: Fix Lesser GPL version number
tricore tcg cpus: Fix Lesser GPL version number
xtensa tcg cpus: Fix Lesser GPL version number
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GCC 9.3.0 thinks that 'method' can be left uninitialized. This code
is already in the "if (bsel || pcihp_bridge_en)" block statement,
but it isn't smart enough to figure it out.
Restrict the code to be used only in the "if (bsel || pcihp_bridge_en)"
block statement to fix (on Ubuntu):
../hw/i386/acpi-build.c: In function 'build_append_pci_bus_devices':
../hw/i386/acpi-build.c:496:9: error: 'method' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
496 | aml_append(parent_scope, method);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: df4008c9c5 ("piix4: don't reserve hw resources when hotplug is off globally")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201108204535.2319870-4-philmd@redhat.com>
Message-Id: <20201110192316.26397-8-alex.bennee@linaro.org>
The v variable goes negative for reg < 0x20. Reorder the code
to first sanity check then calculate v and assign intr to make
sanity checkers happy.
Buglink: https://bugs.launchpad.net/qemu/+bug/1902112
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201105134112.25119-7-kraxel@redhat.com
Add property so scsi command logging can be switched
at runtime instead of compile time.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201105134112.25119-3-kraxel@redhat.com
Replace most DPRINTF macros with trace events.
Drop some DPRINTF macros.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201105134112.25119-2-kraxel@redhat.com
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124134.20083-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023123749.19941-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023123516.19843-1-chetan4windows@gmail.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023123034.19609-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Fixed subject]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122913.19561-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122332.19369-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122157.19321-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023121933.19227-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201019061126.3102-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201016145346.27167-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
If an interrupt occurs between when we claim and complete an interrupt
we currently drop the interrupt in ibex_plic_irqs_set_pending(). This
somewhat matches hardware that also ignore the interrupt between the
claim and complete process.
In the case of hardware though the physical interrupt line will still
be asserted after we have completed the interrupt. This means we will
still act on the interrupt after the complete process. In QEMU we don't
and instead we drop the interrupt as it is never recorded.
This patch changed the behaviour of the Ibex PLIC so that we save all
interrupts that occur while we are between claiming and completing an
interrupt so that we can act on them after the completition process.
This fixes interrupts being dropped when running Tock on OpenTitain in
QEMU.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: e7bcf98c6925b1e6e7828e7c3f85293a09a65b12.1605136387.git.alistair.francis@wdc.com
Storing properties directly in XHCIPciState.xhci doesn't work,
the object_initialize_child() call in xhci_instance_init() will
overwrite them.
This changes the defaults for some properties, which in turn breaks
live migration and possibly other things as well.
So add XHCINecState, store properties there, copy them over on
instance init.
Fixes: 8ddab8dd3d ("usb/hcd-xhci: Split pci wrapper for xhci base model")
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201112103741.2335-1-kraxel@redhat.com
The '%u' conversion specifier is for decimal notation.
When prefixing a format with '0x', we want the hexadecimal
specifier ('%x').
Inspired-by: Dov Murik <dovmurik@linux.vnet.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20201103112558.2554390-3-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit ec87f206d7 ("cirrus: replace debug printf with trace points")
forgot to remove this code once replaced. Do it now.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20201103112558.2554390-2-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since commit 755fba11fb and 8ddab8dd3d we can not build
USB_XHCI_NEC without USB_XHCI_PCI. Correct the Kconfig
dependency.
Fixes: 755fba11fb ("usb/hcd-xhci: Move qemu-xhci device to hcd-xhci-pci.c")
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201109135300.2592982-2-philmd@redhat.com
[ kraxel: restore "default y if PCI_DEVICES" because
"qemu-system-ppc64 -M pseries,usb=on" needs USB_XHCI_NEC=y ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
GCC 9.3.0 thinks that 'method' can be left uninitialized. This code
is already in the "if (bsel || pcihp_bridge_en)" block statement,
but it isn't smart enough to figure it out.
Restrict the code to be used only in the "if (bsel || pcihp_bridge_en)"
block statement to fix (on Ubuntu):
../hw/i386/acpi-build.c: In function 'build_append_pci_bus_devices':
../hw/i386/acpi-build.c:496:9: error: 'method' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
496 | aml_append(parent_scope, method);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: df4008c9c5 ("piix4: don't reserve hw resources when hotplug is off globally")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201107194045.438027-1-philmd@redhat.com>
Acked-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU currently truncates the mmap_offset field when sending
VHOST_USER_ADD_MEM_REG and VHOST_USER_REM_MEM_REG messages. The struct
layout looks like this:
typedef struct VhostUserMemoryRegion {
uint64_t guest_phys_addr;
uint64_t memory_size;
uint64_t userspace_addr;
uint64_t mmap_offset;
} VhostUserMemoryRegion;
typedef struct VhostUserMemRegMsg {
uint32_t padding;
/* WARNING: there is a 32-bit hole here! */
VhostUserMemoryRegion region;
} VhostUserMemRegMsg;
The payload size is calculated as follows when sending the message in
hw/virtio/vhost-user.c:
msg->hdr.size = sizeof(msg->payload.mem_reg.padding) +
sizeof(VhostUserMemoryRegion);
This calculation produces an incorrect result of only 36 bytes.
sizeof(VhostUserMemRegMsg) is actually 40 bytes.
The consequence of this is that the final field, mmap_offset, is
truncated. This breaks x86_64 TCG guests on s390 hosts. Other guest/host
combinations may get lucky if either of the following holds:
1. The guest memory layout does not need mmap_offset != 0.
2. The host is little-endian and mmap_offset <= 0xffffffff so the
truncation has no effect.
Fix this by extending the existing 32-bit padding field to 64-bit. Now
the padding reflects the actual compiler padding. This can be verified
using pahole(1).
Also document the layout properly in the vhost-user specification. The
vhost-user spec did not document the exact layout. It would be
impossible to implement the spec without looking at the QEMU source
code.
Existing vhost-user frontends and device backends continue to work after
this fix has been applied. The only change in the wire protocol is that
QEMU now sets hdr.size to 40 instead of 36. If a vhost-user
implementation has a hardcoded size check for 36 bytes, then it will
fail with new QEMUs. Both QEMU and DPDK/SPDK don't check the exact
payload size, so they continue to work.
Fixes: f1aeb14b08 ("Transmit vhost-user memory regions individually")
Cc: Raphael Norwitz <raphael.norwitz@nutanix.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20201109174355.1069147-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: f1aeb14b08 ("Transmit vhost-user memory regions individually")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
There is a field with vmstate_ghes_state as vmsd in vmstate_ghes_state,
which will lead to infinite recursion in dump_vmstate_vmsd.
Fixes: a08a64627b ("ACPI: Record the Generic Error Status Block address")
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201112020638.874515-1-liangpeng10@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit 348b8d1a76 "macio: don't reference serial_hd() directly within the device"
removed the setting of user_creatable to false on the basis that the restriction
was due to the use of serial_hd() in macio_instance_init().
Unfortunately this isn't the full story since the PIC object property links
must still be set before the device is realized. Whilst it is possible to update
the macio device and Mac machines to resolve this, the fix is too invasive at
this point in the release cycle.
For now simply set user_creatable back to false in macio_class_init() to
prevent QEMU from segfaulting in anticipation of the proper fix arriving in
QEMU 6.0.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201110103111.18395-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of casting an address within a uint8_t array to a
uint32_t*, use stl_le_p(). This handles possibly misaligned
addresses which would otherwise crash on some hosts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The ctucan driver defines types for its registers which are a union
of a uint32_t with a struct with bitfields for the individual
fields within that register. This is a bad idea, because bitfields
aren't portable. The ctu_can_fd_regs.h header works around the
most glaring of the portability issues by defining the
fields in two different orders depending on the setting of the
__LITTLE_ENDIAN_BITFIELD define. However, in ctucan_core.h this
is unconditionally set to 1, which is wrong for big-endian hosts.
Set it only if HOST_WORDS_BIGENDIAN is not set. There is no need
for a "have we defined it already" guard, because the only place
that should set it is ctucan_core.h, which has the usual
double-inclusion guard.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Coverity points out that in ctucan_send_ready_buffers() we
set buff_st_mask = 0xf << (i * 4) inside the loop, but then
we never use it before overwriting it later.
The only thing we use the mask for is as part of the code that is
inserting the new buff_st field into tx_status. That is more
comprehensibly written using deposit32(), so do that and drop the
mask variable entirely.
We also update the buff_st local variable at multiple points
during this function, but nothing can ever see these
intermediate values, so just drop those, write the final
TXT_TOK as a fixed constant value, and collapse the only
remaining set/use of buff_st down into an extract32().
Fixes: Coverity CID 1432869
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The ctucan device has 4 CAN bus cores, each of which has a set of 20
32-bit registers for writing the transmitted data. The registers are
however not contiguous; each core's buffers is 0x100 bytes after
the last.
We got the checks on the address wrong in the ctucan_mem_write()
function:
* the first "is addr in range at all" check allowed
addr == CTUCAN_CORE_MEM_SIZE, which is actually the first
byte off the end of the range
* the decode of addresses into core-number plus offset in the
tx buffer for that core failed to check that the offset was
in range, so the guest could write off the end of the
tx_buffer[] array
NB: currently the values of CTUCAN_CORE_MEM_SIZE, CTUCAN_CORE_TXBUF_NUM,
etc, make "buff_num >= CTUCAN_CORE_TXBUF_NUM" impossible, but we
retain this as a runtime check rather than an assertion to permit
those values to be changed in future (in hardware they are
configurable synthesis parameters).
Fix the top level check, and check the offset is within the buffer.
Fixes: Coverity CID 1432874
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Advertise both types of events as supported when the guest OS
queries the pvpanic device. Currently only PVPANIC_PANICKED is
exposed; PVPANIC_CRASHLOADED must also be advertised, but only on
new machine types.
Fixes: 7dc58deea7 ("pvpanic: implement crashloaded event handling")
Reported-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the peer's type is vdpa, we need to set the mac address to hardware
in virtio_net_device_realize,
Signed-off-by: Cindy Lu <lulu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
* Oss-fuzz updates
* Publish the docs built during gitlab CI to the user's gitlab.io page
* Update the OpenBSD VM test to v6.8
* Fix the device-crash-test script to run with the meson build system
* Some small s390x fixes
-----BEGIN PGP SIGNATURE-----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=a3YE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-11-10' into staging
* Some small qtest fixes
* Oss-fuzz updates
* Publish the docs built during gitlab CI to the user's gitlab.io page
* Update the OpenBSD VM test to v6.8
* Fix the device-crash-test script to run with the meson build system
* Some small s390x fixes
# gpg: Signature made Tue 10 Nov 2020 11:05:06 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-11-10:
s390x: Avoid variable size warning in ipl.h
s390x: fix clang 11 warnings in cpu_models.c
qtest: Update references to parse_escape() in comments
fuzz: add virtio-blk fuzz target
docs: add "page source" link to sphinx documentation
gitlab: force enable docs build in Fedora, Ubuntu, Debian
gitlab: publish the docs built during CI
configure: surface deprecated targets in the help output
fuzz: Make fork_fuzz.ld compatible with LLVM's LLD
scripts/oss-fuzz: give all fuzzers -target names
docs/fuzz: update fuzzing documentation post-meson
docs/fuzz: rST-ify the fuzzing documentation
MAINTAINERS: Add gitlab-pipeline-status script to GitLab CI section
gitlab-ci: Drop generic cache rule
tests/qtest/tpm: Remove redundant check in the tpm_test_swtpm_test()
qtest: Fix bad printf format specifiers
device-crash-test: Check if path is actually an executable file
tests/vm: update openbsd to release 6.8
meson: always include contrib/libvhost-user
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nseries machines have a codepath that allows them to load a
secondary bootloader. This code wasn't checking that the
load_image_targphys() succeeded. Check the return value and report
the error to the user.
While we're in the vicinity, fix the comment style of the
comment documenting what this image load is doing.
Fixes: Coverity CID 1192904
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201103114918.11807-1-peter.maydell@linaro.org
We don't need to fill the full pic[] array if we only use
few of the interrupt lines. Directly call qdev_get_gpio_in()
when necessary.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-6-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MusicPal board code connects both of the IRQ outputs of the UART
to the same INTC qemu_irq. Connecting two qemu_irqs outputs directly
to the same input is not valid as it produces subtly wrong behaviour
(for instance if both the IRQ lines are high, and then one goes
low, the INTC input will see this as a high-to-low transition
even though the second IRQ line should still be holding it high).
This kind of wiring needs an explicitly created OR gate; add one.
Inspired-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
omap2420_mpu_init() introduced in commit 827df9f3c5 ("Add basic
OMAP2 chip support") takes care of creating the 3 UARTs.
Then commit 58a26b477e ("Emulate a serial bluetooth HCI with H4+
extensions and attach to n8x0's UART") added n8x0_uart_setup()
which create the UART and connects it to an IRQ output,
overwritting the existing peripheral and its IRQ connection.
This is incorrect.
Fortunately we don't need to fix this, because commit 6da68df7f9
("hw/arm/nseries: Replace the bluetooth chardev with a "null"
chardev") removed the use of this peripheral. We can simply
remove the code.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The system configuration controller (SYSCFG) doesn't have
any output IRQ (and the INTC input #71 belongs to the UART6).
Remove the invalid code.
Fixes: db635521a0 ("stm32f205: Add the stm32f205 SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can use one MPC per SRAM bank, but we currently only wire the
IRQ from the first expansion MPC to the IRQ splitter. Fix that.
Fixes: bb75e16d5e ("hw/arm/iotkit: Wire up MPC interrupt lines")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using a Cortex-A15, the Virt machine does not use any
MPCore peripherals. Remove the dependency.
Fixes: 7951c7b7c0 ("hw/arm: Express dependencies of the virt machine with Kconfig")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201107114852.271922-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should use printf format specifier "%u" instead of "%d" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 5FA280F5.8060902@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 32bd322a01 ("hw/timer/armv7m_systick: Rewrite to use ptimers")
changed armv7m_systick to build on ptimers. Make sure we have ptimers
in the build when building armv7m_systick.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201104103343.30392-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Ibex PLIC, the other fixes the Hypvervisor access functions.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl+qDs0ACgkQIeENKd+X
cFR/OwgAra3yNXMLZKHSsQt/fGeymv5gfWCbS3T4ncOLUcaC3IXEaf7udmWVhC4S
g9g6OhbO2jofRvSn0t0hZHAAnbTizKwesRXMQFfqAERn66Aa+yHmZYjsJrRHlwMf
MC3XBO5kgDISwvq7/CEI/RO8el2lEScuH9Mdc7cgDnoPpdX1Vy9Hl5RaDdqCHQck
XcqSnpjRkVQ8pKK6OhvDfD/Al5olKoHFR8k3gy+TrSpVsGDubGljOKUY/m7Ihs0m
ZVZMGbn+BISiFnqtoqb9O29ZxMPZv3tolmRPbT7d+4RqgK2cQ3WS63jXejii21ew
KCWv8CSWyGjMo5td+d6V6QXkPNifpg==
=75u0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20201109' into staging
This fixes two bugs in the RISC-V port. One is a bug in the
Ibex PLIC, the other fixes the Hypvervisor access functions.
# gpg: Signature made Tue 10 Nov 2020 03:53:49 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20201109:
hw/intc/ibex_plic: Clear the claim register when read
target/riscv: Split the Hypervisor execute load helpers
target/riscv: Remove the hyp load and store functions
target/riscv: Remove the HS_TWO_STAGE flag
target/riscv: Set the virtualised MMU mode when doing hyp accesses
target/riscv: Add a virtualised MMU Mode
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
S390IPLState contains two IplParameterBlock, which may in turn have
either a IPLBlockPV or a IplBlockFcp, both ending with a variable
sized field (an array).
This causes a warning with clang 11 or greater, which checks that
variable sized type are only allocated at the end of the struct:
In file included from ../qemu-cfi-v3/target/s390x/diag.c:21:
../qemu-cfi-v3/hw/s390x/ipl.h:161:23: error: field 'iplb' with variable sized type 'IplParameterBlock' (aka 'union IplParameterBlock') not at the end of a struct or class is a GNU extension [-Werror,-Wgnu-variable-sized-type-not-at-end]
IplParameterBlock iplb;
^
../qemu-cfi-v3/hw/s390x/ipl.h:162:23: error: field 'iplb_pv' with variable sized type 'IplParameterBlock' (aka 'union IplParameterBlock') not at the end of a struct or class is a GNU extension [-Werror,-Wgnu-variable-sized-type-not-at-end]
IplParameterBlock iplb_pv;
In this case, however, the warning is a false positive, because
IPLBlockPV and IplBlockFcp are allocated in a union wrapped at 4K,
making the union non-variable sized.
Fix the warning by turning the two variable sized arrays into arrays
of size 0. This avoids the compiler error and should produce the
same code.
Signed-off-by: Daniele Buono <dbuono@linux.vnet.ibm.com>
Message-Id: <20201105221905.1350-5-dbuono@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
After claiming the interrupt by reading the claim register we want to
clear the register to make sure the interrupt doesn't appear at the next
read.
This matches the documentation for the claim register as when an interrupt
is claimed by a target the relevant bit of IP is cleared (which we already
do): https://docs.opentitan.org/hw/ip/rv_plic/doc/index.html
This also matches the current hardware.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 68d4575deef2559b7a747f3bda193fcf43af4558.1604629928.git.alistair.francis@wdc.com
Since 7f0f1acedf ("hw/block/nvme: support multiple namespaces"), the
namespaces member of NvmeCtrl is no longer a dynamically allocated
array. Remove the free.
Fixes: 7f0f1acedf ("hw/block/nvme: support multiple namespaces")
Reported-by: Coverity (CID 1436131)
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20201104102248.32168-4-its@irrelevant.dk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
nvme_map_sgl_data erroneously uses the sgls member of NvmeIdNs as a
uint16_t.
Reported-by: Coverity (CID 1436129)
Fixes: cba0a8a344 ("hw/block/nvme: add support for scatter gather lists")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20201104102248.32168-3-its@irrelevant.dk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
As load_device_tree() returns allocated memory,
we need to free it.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Fixes: bda19d7bb5 ("hw/rx: Add RX GDB simulator")
Reported-by: Coverity (CID 1432307: RESOURCE_LEAK)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201102104542.2064745-1-f4bug@amsat.org>
Coverity points out that the error-handling paths in the
boston_fdt_filter() function don't free the fdt that was allocated.
Fix the leak by using g_autofree.
Fixes: Coverity CID 1432275
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201106175823.1650-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
* Fix meson build config for Xen.
* Code style fixes.
-----BEGIN PGP SIGNATURE-----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=TwzC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cschoenebeck/tags/pull-9p-20201106' into staging
9pfs: some fixes
* Fix meson build config for Xen.
* Code style fixes.
# gpg: Signature made Fri 06 Nov 2020 09:12:51 GMT
# gpg: using RSA key 96D8D110CF7AF8084F88590134C2B58765A47395
# gpg: issuer "qemu_oss@crudebyte.com"
# gpg: Good signature from "Christian Schoenebeck <qemu_oss@crudebyte.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: ECAB 1A45 4014 1413 BA38 4926 30DB 47C3 A012 D5F4
# Subkey fingerprint: 96D8 D110 CF7A F808 4F88 5901 34C2 B587 65A4 7395
* remotes/cschoenebeck/tags/pull-9p-20201106:
hw/9pfs: Fix Kconfig dependency problem between 9pfs and Xen
hw/9pfs : add space before the open parenthesis '('
hw/9pfs : open brace '{' following struct go on the same line
hw/9pfs : add spaces around operator
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A small PR this time, one bugfix, one removal of minor dead code, one
warning suppression.
-----BEGIN PGP SIGNATURE-----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=e8LT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-5.2-20201105' into staging
ppc patch queue for 2020-11-05
A small PR this time, one bugfix, one removal of minor dead code, one
warning suppression.
# gpg: Signature made Thu 05 Nov 2020 03:44:51 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-5.2-20201105:
spapr: Convert hpt_prepare_thread() to use qemu_try_memalign()
spapr: Drop dead code in spapr_reallocate_hpt()
target/ppc/excp_helper: Add a fallthrough for fix compiler warning
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Lots of fixes all over the place.
virtio-mem and virtio-iommu patches are kind of fixes but
it seems better to just make them behave sanely than
try to educate users about the limitations ...
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl+i9YMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpySQH/Ru/sxB9PncR1HsqSf0HC0tt/EMKgyZTXEwQ
FITcjkCvBDS98a1VUvvZbjzTEDEZNnoUv94MjdLeBoptJ7GtK6nPoI6Ke0p1Zqbe
mlY2BCb0FpN8FE+mthjAI03mhw6o8Qo/OPtyISQzUxCVVqUHL5TRAVAQdeidoK8n
RBQ4WogwM/h7wI0d9GGgSxAON8IRQnBYImtzJieBb6zeScwKVFTWI1tqBdOyFN0/
AhzQiNZuhZ7a1XGJIsxmWB1NK2kcXNJuOF0ANh4coIHR0JzmH3xRy+Jnf5e3dYsw
LI23DUZPSTJJXAwKPucyTG7RTX8F55N9DVHC9KDRD6Ntq1oreJ4=
=pcbN
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,vhost,virtio: fixes
Lots of fixes all over the place.
virtio-mem and virtio-iommu patches are kind of fixes but
it seems better to just make them behave sanely than
try to educate users about the limitations ...
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 04 Nov 2020 18:40:03 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
contrib/vhost-user-blk: fix get_config() information leak
block/export: fix vhost-user-blk get_config() information leak
block/export: make vhost-user-blk config space little-endian
configure: introduce --enable-vhost-user-blk-server
libvhost-user: follow QEMU comment style
vhost-blk: set features before setting inflight feature
Revert "vhost-blk: set features before setting inflight feature"
net: Add vhost-vdpa in show_netdevs()
vhost-vdpa: Add qemu_close in vhost_vdpa_cleanup
vfio: Don't issue full 2^64 unmap
virtio-iommu: Set supported page size mask
vfio: Set IOMMU page size as per host supported page size
memory: Add interface to set iommu page size mask
virtio-iommu: Add notify_flag_changed() memory region callback
virtio-iommu: Add replay() memory region callback
virtio-iommu: Call memory notifiers in attach/detach
virtio-iommu: Add memory notifiers for map/unmap
virtio-iommu: Store memory region in endpoint struct
virtio-iommu: Fix virtio_iommu_mr()
hw/smbios: Fix leaked fd in save_opt_one() error path
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit b2c00bce54 ("meson: convert hw/9pfs, cleanup") introduced
CONFIG_9PFS (probably a wrong conflict resolution). This config is
not used anywhere. Backends depend on CONFIG_FSDEV_9P which itself
depends on CONFIG_VIRTFS.
Remove the invalid CONFIG_9PFS and use CONFIG_FSDEV_9P instead, to
fix the './configure --without-default-devices --enable-xen' build:
/usr/bin/ld: libcommon.fa.p/hw_xen_xen-legacy-backend.c.o: in function `xen_be_register_common':
hw/xen/xen-legacy-backend.c:754: undefined reference to `xen_9pfs_ops'
/usr/bin/ld: libcommon.fa.p/fsdev_qemu-fsdev.c.o:(.data.rel+0x8): undefined reference to `local_ops'
/usr/bin/ld: libcommon.fa.p/fsdev_qemu-fsdev.c.o:(.data.rel+0x20): undefined reference to `synth_ops'
/usr/bin/ld: libcommon.fa.p/fsdev_qemu-fsdev.c.o:(.data.rel+0x38): undefined reference to `proxy_ops'
collect2: error: ld returned 1 exit status
Fixes: b2c00bce54 ("meson: convert hw/9pfs, cleanup")
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Message-Id: <20201104115706.3101190-3-philmd@redhat.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Fix code style. Space required before the open parenthesis '('.
Signed-off-by: Xinhao Zhang <zhangxinhao1@huawei.com>
Signed-off-by: Kai Deng <dengkai1@huawei.com>
Reported-by: Euler Robot <euler.robot@huawei.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201030043515.1030223-3-zhangxinhao1@huawei.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Fix code style. Open braces for struct should go on the same line.
Signed-off-by: Xinhao Zhang <zhangxinhao1@huawei.com>
Signed-off-by: Kai Deng <dengkai1@huawei.com>
Reported-by: Euler Robot <euler.robot@huawei.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201030043515.1030223-2-zhangxinhao1@huawei.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
s390-pci-vfio.c calls into the vfio code, so we need it to be
built conditionally on vfio (which implies CONFIG_LINUX).
Fixes: cd7498d07f ("s390x/pci: Add routine to get the vfio dma available count")
Reported-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20201103123237.718242-1-cohuck@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
HPT resizing is asynchronous: the guest first kicks off the creation of a
new HPT, then it waits for that new HPT to be actually created and finally
it asks the current HPT to be replaced by the new one.
In the case of a userland allocated HPT, this currently relies on calling
qemu_memalign() which aborts on OOM and never returns NULL. Since we seem
to have path to report the failure to the guest with an H_NO_MEM return
value, use qemu_try_memalign() instead of qemu_memalign().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160398563636.32380.1747166034877173994.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Sometimes QEMU needs to allocate the HPT in userspace, namely with TCG
or PR KVM. This is performed with qemu_memalign() because of alignment
requirements. Like glib's allocators, its behaviour is to abort on OOM
instead of returning NULL.
This could be changed to qemu_try_memalign(), but in the specific case
of spapr_reallocate_hpt(), the outcome would be to terminate QEMU anyway
since no HPT means no MMU for the guest. Drop the dead code instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160398562892.32380.15006707861753544263.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The source and destination x,y display parameters in ati_2d_blt()
may run off the vga limits if either of s->regs.[src|dst]_[xy] is
zero. Check the parameter values to avoid potential crash.
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20201021103818.1704030-1-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Note that whilst the device does not do anything with these values, they are
logged with trace events and stored to allow future implementation.
The default flow control is set to none at reset as documented in the Linux
ftdi_sio.h header file.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-id: 20201027150456.24606-9-mark.cave-ayland@ilande.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Also implement the behaviour reported in Linux's ftdi_sio.c whereby if an invalid
data_bits value is provided then the hardware defaults to using 8.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201027150456.24606-8-mark.cave-ayland@ilande.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some operating systems will generate a new device ID when a USB device is unplugged
and then replugged into the USB. If this is done whilst switching between multiple
applications over a virtual serial port, the change of device ID requires going
back into the OS/application to locate the new device accordingly.
Add a new always-plugged property that if specified will ensure that the device
always remains attached to the USB regardless of the state of the backend
chardev.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-id: 20201027150456.24606-7-mark.cave-ayland@ilande.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The DeviceOutVendor and DeviceInVendor macros can be replaced with their
equivalent VendorDeviceOutRequest and VendorDeviceRequest macros from usb.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201027150456.24606-6-mark.cave-ayland@ilande.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20201103123617.28256-1-jin.yu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit adb29c0273.
The commit broke -device vhost-user-blk-pci because the
vhost_dev_prepare_inflight() function it introduced segfaults in
vhost_dev_set_features() when attempting to access struct vhost_dev's
vdev pointer before it has been assigned.
To reproduce the segfault simply launch a vhost-user-blk device with the
contrib vhost-user-blk device backend:
$ build/contrib/vhost-user-blk/vhost-user-blk -s /tmp/vhost-user-blk.sock -r -b /var/tmp/foo.img
$ build/qemu-system-x86_64 \
-device vhost-user-blk-pci,id=drv0,chardev=char1,addr=4.0 \
-object memory-backend-memfd,id=mem,size=1G,share=on \
-M memory-backend=mem,accel=kvm \
-chardev socket,id=char1,path=/tmp/vhost-user-blk.sock
Segmentation fault (core dumped)
Cc: Jin Yu <jin.yu@intel.com>
Cc: Raphael Norwitz <raphael.norwitz@nutanix.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20201102165709.232180-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
IOMMUs may declare memory regions spanning from 0 to UINT64_MAX. When
attempting to deal with such region, vfio_listener_region_del() passes a
size of 2^64 to int128_get64() which throws an assertion failure. Even
ignoring this, the VFIO_IOMMU_DMA_MAP ioctl cannot handle this size
since the size field is 64-bit. Split the request in two.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-11-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to the loongson spec
(http://www.loongson.cn/uploadfile/cpu/3B1500/Loongson_3B1500_cpu_user_1.pdf)
and the macro definition(#define R_PERCORE_ISR(x) (0x40 + 0x8 * x)), we know
that the ISR size per CORE is 8, so here we need to divide
(addr - R_PERCORE_ISR(0)) by 8, not 4.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <5FA12391.8090400@huawei.com>
[PMD: Shortened subject]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201023122633.19466-1-chetan4windows@gmail.com>
[PMD: Added hw/mips/ prefix in subject]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201016143509.26692-1-chetan4windows@gmail.com>
[PMD: Split hw/ vs target/]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We deprecated the support for the 'r4k' machine for the 5.0 release
(commit d32dc61421), which means that our deprecation policy allows
us to drop it in release 5.2. Remove the code.
To repeat the rationale from the deprecation note:
- this virtual machine has no specification
- the Linux kernel dropped support for it 10 years ago
Users are recommended to use the Malta board instead.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
ACKed-by: Peter Krempa <pkrempa@redhat.com>
Message-Id: <20201102201311.2220005-1-f4bug@amsat.org>
The latest SD card image [1] released by Microchip ships a Linux
kernel with built-in PolarFire SoC I2C driver support. The device
tree file includes the description for the I2C1 node hence kernel
tries to probe the I2C1 device during boot.
It is enough to create an unimplemented device for I2C1 to allow
the kernel to continue booting to the shell.
[1] ftp://ftpsoc.microsemi.com/outgoing/core-image-minimal-dev-icicle-kit-es-sd-20201009141623.rootfs.wic.gz
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-11-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When system memory is larger than 1 GiB (high memory), PolarFire SoC
maps it at address 0x10_0000_0000. Address 0xC000_0000 and above is
aliased to the same 1 GiB low memory with different cache attributes.
At present QEMU maps the system memory contiguously from 0x8000_0000.
This corrects the wrong QEMU logic. Note address 0x14_0000_0000 is
the alias to the high memory, and even physical memory is only 1 GiB,
the HSS codes still tries to probe the high memory alias address.
It seems there is no issue on the real hardware, so we will have to
take that into the consideration in our emulation. Due to this, we
we increase the default system memory size to 1537 MiB (the minimum
required high memory size by HSS) so that user gets notified an error
when less than 1537 MiB is specified.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201101170538.3732-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Somehow HSS needs to access address 0 [1] for the DDR calibration data
which is in the chipset's reserved memory. Let's map it.
[1] See the config_copy() calls in various places in ddr_setup() in
the HSS source codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-9-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously SYSREG was created as an unimplemented device. Now that
we have a simple SYSREG module, connect it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-8-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This creates a minimum model for Microchip PolarFire SoC SYSREG
module. It only implements the ENVM_CR register to tell guest
software that eNVM is running at the configured divider rate.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-7-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously IOSCB_CFG was created as an unimplemented device. With
the new IOSCB model, its memory range is already covered by the
IOSCB hence remove the previous unimplemented device creation in
the SoC codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-6-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This creates a model for PolarFire SoC IOSCB [1] module. It actually
contains lots of sub-modules like various PLLs to control different
peripherals. Only the mininum capabilities are emulated to make the
HSS DDR memory initialization codes happy. Lots of sub-modules are
created as an unimplemented devices.
[1] PF_SoC_RegMap_V1_1/MPFS250T/mpfs250t_ioscb_memmap_dri.htm in
https://www.microsemi.com/document-portal/doc_download/1244581-polarfire-soc-register-map
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-5-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect DDR SGMII PHY module and CFG module to the PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-4-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The PolarFire SoC DDR Memory Controller mainly includes 2 modules,
called SGMII PHY module and the CFG module, as documented in the
chipset datasheet.
This creates a single file that groups these 2 modules, providing
the minimum functionalities that make the HSS DDR initialization
codes happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-3-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
It is not easy to find out the memory map for a specific component
in the PolarFire SoC as the information is scattered in different
documents. Add some comments so that people can know where to get
such information from the Microchip website.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-2-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add sifive_plic vmstate for supporting sifive_plic migration.
Current vmstate framework only supports one structure parameter
as num field to describe variable length arrays, so introduce
num_enables.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Yipeng Yin <yinyipeng1@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201026115530.304-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Extend virt machine to allow passing custom DTB using "-dtb"
command-line parameter. This will help users pass modified DTB
to virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201022053225.2596110-2-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Extend sifive_u machine to allow passing custom DTB using "-dtb"
command-line parameter. This will help users pass modified DTB
or Linux SiFive DTB to sifive_u machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201022053225.2596110-1-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
libFuzzer triggered the following assertion:
cat << EOF | qemu-system-i386 -M pc-q35-5.0 \
-nographic -monitor none -serial none \
-qtest stdio -d guest_errors -trace pci\*
outl 0xcf8 0x8400f841
outl 0xcfc 0xebed205d
outl 0x5d02 0xedf82049
EOF
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
hw/pci/pci.c:268: int pci_bus_get_irq_level(PCIBus *, int): Assertion `irq_num < bus->nirq' failed.
This is because ich9_lpc_sci_irq() returns -1 for reserved
(illegal) values, but ich9_lpc_pmbase_sci_update() considers
it valid and store it in a 8-bit unsigned type. Then the 255
value is used as GSI IRQ, resulting in a PIRQ value of 247,
more than ICH9_LPC_NB_PIRQS (8).
Fix by simply ignoring the invalid access (and reporting it):
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
ICH9 LPC: SCI IRQ SEL #3 is reserved
pci_cfg_read mch 00:0 @0x0 -> 0x8086
pci_cfg_read mch 00:0 @0x0 -> 0x29c08086
...
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: 8f242cb724 ("ich9: implement SCI_IRQ_SEL register")
BugLink: https://bugs.launchpad.net/qemu/+bug/1878642
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200717151705.18611-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The virtio-iommu device can deal with arbitrary page sizes for virtual
endpoints, but for endpoints assigned with VFIO it must follow the page
granule used by the host IOMMU driver.
Implement the interface to set the vIOMMU page size mask, called by VFIO
for each endpoint. We assume that all host IOMMU drivers use the same
page granule (the host page granule). Override the page_size_mask field
in the virtio config space.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-10-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Set IOMMU supported page size mask same as host Linux supported page
size mask.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-9-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add notify_flag_changed() to notice when memory listeners are added and
removed.
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-7-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement the replay callback to setup all mappings for a new memory
region.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-6-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Call the memory notifiers when attaching an endpoint to a domain, to
replay existing mappings, and when detaching the endpoint, to remove all
mappings.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-5-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extend VIRTIO_IOMMU_T_MAP/UNMAP request to notify memory listeners. It
will call VFIO notifier to map/unmap regions in the physical IOMMU.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-4-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Store the memory region associated to each endpoint into the endpoint
structure, to allow efficient memory notification on map/unmap.
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-3-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Due to an invalid mask, virtio_iommu_mr() may return the wrong memory
region. It hasn't been too problematic so far because the function was
only used to test existence of an endpoint, but that is about to change.
Fixes: cfb42188b2 ("virtio-iommu: Implement attach/detach command")
Cc: QEMU Stable <qemu-stable@nongnu.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20201030180510.747225-2-jean-philippe@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix the following Coverity issue (RESOURCE_LEAK):
CID 1432879: Resource leak
Handle variable fd going out of scope leaks the handle.
Replace a close() call by qemu_close() since the handle is
opened with qemu_open().
Fixes: bb99f4772f ("hw/smbios: support loading OEM strings values from a file")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201030152742.1553968-1-philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix uninitialized value issues reported by Coverity:
Field 'msg.reserved' is uninitialized when calling write().
While the 'struct vhost_msg' does not have a 'reserved' field,
we still initialize it to have the two parts of the function
consistent.
Reported-by: Coverity (CID 1432864: UNINIT)
Fixes: c471ad0e9b ("vhost_net: device IOTLB support")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201103063541.2463363-1-philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix code style. Operator needs spaces both sides.
Signed-off-by: Xinhao Zhang <zhangxinhao1@huawei.com>
Signed-off-by: Kai Deng <dengkai1@huawei.com>
Message-Id: <20201103102634.273021-3-zhangxinhao1@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix code style. Space required before the open parenthesis '('.
Signed-off-by: Xinhao Zhang <zhangxinhao1@huawei.com>
Signed-off-by: Kai Deng <dengkai1@huawei.com>
Message-Id: <20201103102634.273021-2-zhangxinhao1@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix code style. Don't use '#' flag of printf format ('%#') in
format strings, use '0x' prefix instead
Signed-off-by: Xinhao Zhang <zhangxinhao1@huawei.com>
Signed-off-by: Kai Deng <dengkai1@huawei.com>
Message-Id: <20201103102634.273021-1-zhangxinhao1@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The block size determines the alignment requirements. Implement
get_min_alignment() of the TYPE_MEMORY_DEVICE interface.
This allows auto-assignment of a properly aligned address in guest
physical address space. For example, when specifying a 2GB block size
for a virtio-mem device with 10GB with a memory setup "-m 4G, 20G",
we'll no longer fail when realizing.
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201008083029.9504-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a callback that can be used to express additional alignment
requirements (exceeding the ones from the memory region).
Will be used by virtio-mem to express special alignment requirements due
to manually configured, big block sizes (e.g., 1GB with an ordinary
memory-backend-ram). This avoids failing later when realizing, because
auto-detection wasn't able to assign a properly aligned address.
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201008083029.9504-6-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's warn instead of bailing out - the worst thing that can happen is
that we'll fail hot/coldplug later. The user got warned, and this should
be rare.
This will be necessary for memory devices with rather big (user-defined)
alignment requirements - say a virtio-mem device with a 2G block size -
which will become important, for example, when supporting vfio in the
future.
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201008083029.9504-5-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's allow a minimum block size of 1 MiB in all configurations. Select
the default block size based on
- The page size of the memory backend.
- The THP size if the memory backend size corresponds to the real host
page size.
- The global minimum of 1 MiB.
and warn if something smaller is configured by the user.
VIRTIO_MEM only supports Linux (depends on LINUX), so we can probe the
THP size unconditionally.
For now we only support virtio-mem on x86-64 - there isn't a user-visible
change (x86-64 only supports 2 MiB THP on the PMD level) - the default
was, and will be 2 MiB.
If we ever have THP on the PUD level (e.g., 1 GiB THP on x86-64), we
expect it to be more transparent - e.g., to only optimize fully populated
ranges unless explicitly told /configured otherwise (in contrast to PMD
THP).
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201008083029.9504-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The spec states:
"The device MUST set addr, region_size, usable_region_size, plugged_size,
requested_size to multiples of block_size."
With block sizes > 256MB, we currently wouldn't guarantee that for the
usable_region_size.
Note that we cannot exceed the region_size, as we already enforce the
alignment there properly.
Fixes: 910b25766b ("virtio-mem: Paravirtualized memory hot(un)plug")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201008083029.9504-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The spec states:
"The device MUST set addr, region_size, usable_region_size, plugged_size,
requested_size to multiples of block_size."
In some cases, we currently don't guarantee that for "addr": For example,
when starting a VM with 4 GiB boot memory and a virtio-mem device with a
block size of 2 GiB, "memaddr"/"addr" will be auto-assigned to
0x140000000 (5 GiB).
We'll try to improve auto-assignment for memory devices next, to avoid
bailing out in case memory device code selects a bad address.
Note: The Linux driver doesn't support such big block sizes yet.
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Fixes: 910b25766b ("virtio-mem: Paravirtualized memory hot(un)plug")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201008083029.9504-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----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=s4KC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/nvme/tags/pull-nvme-20201102' into staging
nvme pull 2 Nov 2020
# gpg: Signature made Mon 02 Nov 2020 15:20:30 GMT
# gpg: using RSA key DBC11D2D373B4A3755F502EC625156610A4F6CC0
# gpg: Good signature from "Keith Busch <kbusch@kernel.org>" [unknown]
# gpg: aka "Keith Busch <keith.busch@gmail.com>" [unknown]
# gpg: aka "Keith Busch <keith.busch@intel.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DBC1 1D2D 373B 4A37 55F5 02EC 6251 5661 0A4F 6CC0
* remotes/nvme/tags/pull-nvme-20201102: (30 commits)
hw/block/nvme: fix queue identifer validation
hw/block/nvme: fix create IO SQ/CQ status codes
hw/block/nvme: fix prp mapping status codes
hw/block/nvme: report actual LBA data shift in LBAF
hw/block/nvme: add trace event for requests with non-zero status code
hw/block/nvme: add nsid to get/setfeat trace events
hw/block/nvme: reject io commands if only admin command set selected
hw/block/nvme: support for admin-only command set
hw/block/nvme: validate command set selected
hw/block/nvme: support per-namespace smart log
hw/block/nvme: fix log page offset check
hw/block/nvme: remove pointless rw indirection
hw/block/nvme: update nsid when registered
hw/block/nvme: change controller pci id
pci: allocate pci id for nvme
hw/block/nvme: support multiple namespaces
hw/block/nvme: refactor identify active namespace id list
hw/block/nvme: add support for sgl bit bucket descriptor
hw/block/nvme: add support for scatter gather lists
hw/block/nvme: harden cmb access
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In gicv3_init_cpuif() we copy the ARMCPU gicv3_maintenance_interrupt
into the GICv3CPUState struct's maintenance_irq field. This will
only work if the board happens to have already wired up the CPU
maintenance IRQ before the GIC was realized. Unfortunately this is
not the case for the 'virt' board, and so the value that gets copied
is NULL (since a qemu_irq is really a pointer to an IRQState struct
under the hood). The effect is that the CPU interface code never
actually raises the maintenance interrupt line.
Instead, since the GICv3CPUState has a pointer to the CPUState, make
the dereference at the point where we want to raise the interrupt, to
avoid an implicit requirement on board code to wire things up in a
particular order.
Reported-by: Jose Martins <josemartins90@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201009153904.28529-1-peter.maydell@linaro.org
Reviewed-by: Luc Michel <luc@lmichel.fr>
In exynos4210_fimd_update(), the pointer s is dereferinced before
being check if it is valid, which may lead to NULL pointer dereference.
So move the assignment to global_width after checking that the s is valid.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 5F9F8D88.9030102@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In omap_lcd_interrupts(), the pointer omap_lcd is dereferinced before
being check if it is valid, which may lead to NULL pointer dereference.
So move the assignment to surface after checking that the omap_lcd is valid
and move surface_bits_per_pixel(surface) to after the surface assignment.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: AlexChen <alex.chen@huawei.com>
Message-id: 5F9CDB8A.9000001@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting a CPU with EL3 using the -kernel flag, set up CPTR_EL3 so
that SVE will not trap to EL3.
Signed-off-by: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030151541.11976-1-remi@remlab.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BIT_ULL() macro to ensure we use 64-bit arithmetic.
This fixes the following Coverity issue (OVERFLOW_BEFORE_WIDEN):
CID 1432363 (#1 of 1): Unintentional integer overflow:
overflow_before_widen:
Potentially overflowing expression 1 << scale with type int
(32 bits, signed) is evaluated using 32-bit arithmetic, and
then used in a context that expects an expression of type
hwaddr (64 bits, unsigned).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201030144617.1535064-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is to allow IDE disks to be unplugged when adding to QEMU via:
-drive file=/root/disk_file,if=none,id=ide-disk0,format=raw
-device ide-hd,drive=ide-disk0,bus=ide.0,unit=0
as the current code only works for disk added with:
-drive file=/root/disk_file,if=ide,index=0,media=disk,format=raw
Since the code already have the IDE controller as `dev`, we don't need
to use the legacy DriveInfo to find all the drive we want to unplug.
We can simply use `blk` from the controller, as it kind of was already
assume to be the same, by setting it to NULL.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20201027154058.495112-1-anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The type of input variable is unsigned int
while the printer type is int. So fix incorrect print type.
Signed-off-by: Zhengui li <lizhengui@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use the capability chains of the VFIO_DEVICE_GET_INFO ioctl to retrieve
the CLP information that the kernel exports.
To be compatible with previous kernel versions we fall back on previous
predefined values, same as the emulation values, when the ioctl is found
to not support capability chains. If individual CLP capabilities are not
found, we fall back on default values for only those capabilities missing
from the chain.
This patch is based on work previously done by Pierre Morel.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: non-Linux build fixes]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now that VFIO_DEVICE_GET_INFO supports capability chains, add a helper
function to find specific capabilities in the chain.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use a ClpRspQueryPci structure to hold the information related to a
zPCI Function.
This allows us to be ready to support different zPCI functions and to
retrieve the zPCI function information from the host.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add a step to remove all stashed PCI groups to avoid stale data between
machine resets.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use a S390PCIGroup structure to hold the information related to a
zPCI Function group.
This allows us to be ready to support multiple groups and to retrieve
the group information from the host.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When an s390 guest is using lazy unmapping, it can result in a very
large number of oustanding DMA requests, far beyond the default
limit configured for vfio. Let's track DMA usage similar to vfio
in the host, and trigger the guest to flush their DMA mappings
before vfio runs out.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: non-Linux build fixes]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Create new files for separating out vfio-specific work for s390
pci. Add the first such routine, which issues VFIO_IOMMU_GET_INFO
ioctl to collect the current dma available count.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: Fix non-Linux build with CONFIG_LINUX]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The underlying host may be limiting the number of outstanding DMA
requests for type 1 IOMMU. Add helper functions to check for the
DMA available capability and retrieve the current number of DMA
mappings allowed.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: vfio_get_info_dma_avail moved inside CONFIG_LINUX]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Rather than duplicating the same loop in multiple locations,
create a static function to do the work.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Seems a more appropriate location for them.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added amount of bytes transferred to the VM at destination by all VFIO
devices
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If the device is not a failover primary device, call
vfio_migration_probe() and vfio_migration_finalize() to enable
migration support for those devices that support it respectively to
tear it down again.
Removed migration blocker from VFIO PCI device specific structure and use
migration blocker from generic structure of VFIO device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With vIOMMU, IO virtual address range can get unmapped while in pre-copy
phase of migration. In that case, unmap ioctl should return pages pinned
in that range and QEMU should find its correcponding guest physical
addresses and report those dirty.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
[aw: fix error_report types, fix cpu_physical_memory_set_dirty_lebitmap() cast]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When vIOMMU is enabled, register MAP notifier from log_sync when all
devices in container are in stop and copy phase of migration. Call replay
and get dirty pages from notifier callback.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio_listener_log_sync gets list of dirty pages from container using
VFIO_IOMMU_GET_DIRTY_BITMAP ioctl and mark those pages dirty when all
devices are stopped and saving state.
Return early for the RAM block section of mapped MMIO region.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
[aw: fix error_report types, fix cpu_physical_memory_set_dirty_lebitmap() cast]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Call VFIO_IOMMU_DIRTY_PAGES ioctl to start and stop dirty pages tracking
for VFIO devices.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added helper functions to get IOMMU info capability chain.
Added function to get migration capability information from that
capability chain for IOMMU container.
Similar change was proposed earlier:
https://lists.gnu.org/archive/html/qemu-devel/2018-05/msg03759.html
Disable migration for devices if IOMMU module doesn't support migration
capability.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Cc: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Cc: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Sequence during _RESUMING device state:
While data for this device is available, repeat below steps:
a. read data_offset from where user application should write data.
b. write data of data_size to migration region from data_offset.
c. write data_size which indicates vendor driver that data is written in
staging buffer.
For user, data is opaque. User should write data in the same order as
received.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added .save_live_pending, .save_live_iterate and .save_live_complete_precopy
functions. These functions handles pre-copy and stop-and-copy phase.
In _SAVING|_RUNNING device state or pre-copy phase:
- read pending_bytes. If pending_bytes > 0, go through below steps.
- read data_offset - indicates kernel driver to write data to staging
buffer.
- read data_size - amount of data in bytes written by vendor driver in
migration region.
- read data_size bytes of data from data_offset in the migration region.
- Write data packet to file stream as below:
{VFIO_MIG_FLAG_DEV_DATA_STATE, data_size, actual data,
VFIO_MIG_FLAG_END_OF_STATE }
In _SAVING device state or stop-and-copy phase
a. read config space of device and save to migration file stream. This
doesn't need to be from vendor driver. Any other special config state
from driver can be saved as data in following iteration.
b. read pending_bytes. If pending_bytes > 0, go through below steps.
c. read data_offset - indicates kernel driver to write data to staging
buffer.
d. read data_size - amount of data in bytes written by vendor driver in
migration region.
e. read data_size bytes of data from data_offset in the migration region.
f. Write data packet as below:
{VFIO_MIG_FLAG_DEV_DATA_STATE, data_size, actual data}
g. iterate through steps b to f while (pending_bytes > 0)
h. Write {VFIO_MIG_FLAG_END_OF_STATE}
When data region is mapped, its user's responsibility to read data from
data_offset of data_size before moving to next steps.
Added fix suggested by Artem Polyakov to reset pending_bytes in
vfio_save_iterate().
Added fix suggested by Zhi Wang to add 0 as data size in migration stream and
add END_OF_STATE delimiter to indicate phase complete.
Suggested-by: Artem Polyakov <artemp@nvidia.com>
Suggested-by: Zhi Wang <zhi.wang.linux@gmail.com>
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Define flags to be used as delimiter in migration stream for VFIO devices.
Added .save_setup and .save_cleanup functions. Map & unmap migration
region from these functions at source during saving or pre-copy phase.
Set VFIO device state depending on VM's state. During live migration, VM is
running when .save_setup is called, _SAVING | _RUNNING state is set for VFIO
device. During save-restore, VM is paused, _SAVING state is set for VFIO device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added migration state change notifier to get notification on migration state
change. These states are translated to VFIO device state and conveyed to
vendor driver.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VM state change handler is called on change in VM's state. Based on
VM state, VFIO device state should be changed.
Added read/write helper functions for migration region.
Added function to set device_state.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[aw: lx -> HWADDR_PRIx, remove redundant parens]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Whether the VFIO device supports migration or not is decided based of
migration region query. If migration region query is successful and migration
region initialization is successful then migration is supported else
migration is blocked.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Added functions to save and restore PCI device specific data,
specifically config space of PCI device.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This function will be used for migration region.
Migration region is mmaped when migration starts and will be unmapped when
migration is complete.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Just a bunch of bugfixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl+cCq8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpKWkH/0qq+u2z/q0KYzmodcdW2eFNsvKF2e+Dz3Af
zZGMREH93DsKAQ2k3t84sz2RAaAP45cCqrq+v8kSzmpaC7GqKYA/VceeLwy8e6Eu
YKvu5QixrOVTpNg2QV/w44ywgtA4NbWy5Fr9S4qhzPyyD/gtE609weZ1vQnSFT7B
Gg4vr1lcqskwYTH7sh+bpsDTUeANr7QaknWKnaomroz+IUO8m9ig6RKtegaXhQCj
xswI4458S3nklqnoGMa56j46VYwft8YHO1lBiR1WefTHylknyng9Tdvf9G5mnzVg
wyrMTuT36lMXIa5KcSZeECIt2ZUT6KSSjWzEKZNXL5lS3gfUo7o=
=powp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,vhost,virtio: misc fixes
Just a bunch of bugfixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 30 Oct 2020 12:44:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
intel_iommu: Fix two misuse of "0x%u" prints
virtio: skip guest index check on device load
vhost-blk: set features before setting inflight feature
pci: Disallow improper BAR registration for type 1
pci: Change error_report to assert(3)
pci: advertise a page aligned ATS
pc: Implement -no-hpet as sugar for -machine hpet=on
vhost: Don't special case vq->used_phys in vhost_get_log_size()
pci: Assert irqnum is between 0 and bus->nirqs in pci_bus_change_irq_level
hw/pci: Extract pci_bus_change_irq_level() from pci_change_irq_level()
hw/virtio/vhost-vdpa: Fix Coverity CID 1432864
acpi/crs: Support ranges > 32b for hosts
acpi/crs: Prevent bad ranges for host bridges
vhost-vsock: set vhostfd to non-blocking mode
vhost-vdpa: negotiate VIRTIO_NET_F_STATUS with driver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Dave magically found this. Fix them with "0x%x".
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201019173922.100270-1-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU must be careful when loading device state off migration streams to
prevent a malicious source from exploiting the emulator. Overdoing these
checks has the side effect of allowing a guest to "pin itself" in cloud
environments by messing with state which is entirely in its control.
Similarly to what f3081539 achieved in usb_device_post_load(), this
commit removes such a check from virtio_load(). Worth noting, the result
of a load without this check is the same as if a guest enables a VQ with
invalid indexes to begin with. That is, the virtual device is set in a
broken state (by the datapath handler) and must be reset.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Message-Id: <20201028134643.110698-1-felipe@nutanix.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Message-Id: <20200910134851.7817-1-jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Prevent future developers working on root complexes, root ports, or
bridges that also wish to implement a BAR for those, from shooting
themselves in the foot. PCI type 1 headers only support 2 base address
registers. It is incorrect and difficult to figure out what is wrong
with the device when this mistake is made. With this, it is immediate
and obvious what has gone wrong.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201015181411.89104-2-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Asserts are used for developer bugs. As registering a bar of the wrong
size is not something that should be possible for a user to achieve,
this is a developer bug.
While here, use the more obvious helper function.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201015181411.89104-1-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
After Linux kernel commit 61363c1474b1 ("iommu/vt-d: Enable ATS only
if the device uses page aligned address."), ATS will be only enabled
if device advertises a page aligned request.
Unfortunately, vhost-net is the only user and we don't advertise the
aligned request capability in the past since both vhost IOTLB and
address_space_get_iotlb_entry() can support non page aligned request.
Though it's not clear that if the above kernel commit makes
sense. Let's advertise a page aligned ATS here to make vhost device
IOTLB work with Intel IOMMU again.
Note that in the future we may extend pcie_ats_init() to accept
parameters like queue depth and page alignment.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200909081731.24688-1-jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Get rid of yet another global variable.
The default will be hpet=on only if CONFIG_HPET=y.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20201021144716.1536388-1-ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The first loop in vhost_get_log_size() computes the size of the dirty log
bitmap so that it allows to track changes in the entire guest memory, in
terms of GPA.
When not using a vIOMMU, the address of the vring's used structure,
vq->used_phys, is a GPA. It is thus already covered by the first loop.
When using a vIOMMU, vq->used_phys is a GIOVA that will be translated
to an HVA when the vhost backend needs to update the used structure. It
will log the corresponding GPAs into the bitmap but it certainly won't
log the GIOVA.
So in any case, vq->used_phys shouldn't be explicitly used to size the
bitmap. Drop the second loop.
This fixes a crash of the source when migrating a guest using in-kernel
vhost-net and iommu_platform=on on POWER, because DMA regions are put
over 0x800000000000000ULL. The resulting insanely huge log size causes
g_malloc0() to abort.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1879349
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160208823418.29027.15172801181796272300.stgit@bahia.lan>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These assertions similar to those in the adjacent pci_bus_get_irq_level()
function ensure that irqnum lies within the valid PCI bus IRQ range.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201011082022.3016-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201024203900.3619498-3-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract pci_bus_change_irq_level() from pci_change_irq_level() to
make it clearer it operates on the bus.
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201024203900.3619498-2-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix uninitialized value issues reported by Coverity:
Field 'msg.reserved' is uninitialized when calling write().
Fixes: a5bd05800f ("vhost-vdpa: batch updating IOTLB mappings")
Reported-by: Coverity (CID 1432864: UNINIT)
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201028154004.776760-1-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to PCIe spec 5.0 Type 1 header space Base Address Registers
are defined by 7.5.1.2.1 Base Address Registers (same as Type 0). The
_CRS region should allow for the same range (up to 64b). Prior to this
change, any host bridge utilizing more than 32b for the BAR would have
the address truncated and likely lead to conflicts when the operating
systems reads the _CRS object.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201026193924.985014-2-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Prevent _CRS resources being quietly chopped off and instead throw an
assertion. _CRS is used by host bridges to declare regions of io and/or
memory that they consume. On some (all?) platforms the host bridge
doesn't have PCI header space and so they need some way to convey the
information.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201026193924.985014-1-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
vhost IOTLB API uses read()/write() to exchange iotlb messages with
the kernel module.
The QEMU implementation expects a non-blocking fd, indeed commit
c471ad0e9b ("vhost_net: device IOTLB support") set it for vhost-net.
Without this patch, if we enable iommu for the vhost-vsock device,
QEMU can hang when exchanging IOTLB messages.
As commit 894022e616 ("net: check if the file descriptor is valid
before using it") did for tap, let's use qemu_try_set_nonblock()
when fd is provided by the user.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20201029144849.70958-1-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
-----BEGIN PGP SIGNATURE-----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=igPS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.2-20201028' into staging
ppc patch queue 2020-10-28
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
# gpg: Signature made Tue 27 Oct 2020 14:13:21 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.2-20201028:
ppc/: fix some comment spelling errors
spapr: Improve spapr_reallocate_hpt() error reporting
target/ppc: Fix kvmppc_load_htab_chunk() error reporting
spapr: Use error_append_hint() in spapr_reallocate_hpt()
spapr: Simplify error handling in spapr_memory_plug()
spapr: Pass &error_abort when getting some PC DIMM properties
spapr: Use appropriate getter for PC_DIMM_SLOT_PROP
spapr: Use appropriate getter for PC_DIMM_ADDR_PROP
pc-dimm: Drop @errp argument of pc_dimm_plug()
spapr: Simplify spapr_cpu_core_realize() and spapr_cpu_core_unrealize()
spapr: Make spapr_cpu_core_unrealize() idempotent
spapr: Drop spapr_delete_vcpu() unused argument
spapr: Unrealize vCPUs with qdev_unrealize()
spapr: Fix leak of CPU machine specific data
spapr: Move spapr_create_nvdimm_dr_connectors() to core machine code
hw/net: move allocation to the heap due to very large stack frame
ppc/spapr: re-assert IRQs during event-scan if there are pending
spapr: Clarify why DR connectors aren't user creatable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no actual code in the CONFIG_VIRGL=n case. So building is
(a) pointless and (b) makes macos ranlib complain.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20201026142851.28735-1-kraxel@redhat.com
Build virtio-gpu vga devices modular. Must be a separate module because
not all qemu softmmu variants come with VGA support.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20201023064618.21409-3-kraxel@redhat.com
Build virtio-gpu pci devices modular. Must be a separate module because
not all qemu softmmu variants come with PCI support.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201023064618.21409-2-kraxel@redhat.com
We only need to zero-initialize 'val' once.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201012170950.3491912-4-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The region is registered as 64KiB in sabre_init():
memory_region_init_io(&s->sabre_config, OBJECT(s), &sabre_config_ops, s,
"sabre-config", 0x10000);
Remove the superfluous check.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201012170950.3491912-3-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The current link redirects to https://www.oracle.com/sun/
announcing "Oracle acquired Sun Microsystems in 2010, ..."
but does not give hint where to find the datasheet.
Use the archived PDF on the Wayback Machine, which works.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201012170950.3491912-2-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The rework of the sabre IRQs in commit 6864fa3897 "sun4u: update PCI topology to
include simba PCI bridges" changed the IRQ routing so that both PCI and legacy
OBIO IRQs are routed through the sabre PCI host bridge to the CPU.
Unfortunately this commit failed to increase the number of PCI bus IRQs
accordingly meaning that access to the legacy IRQs OBIO (irqnum >= 0x20) would
overflow the PCI bus IRQ array causing strange failures running qemu-system-sparc64
in NetBSD.
Cc: qemu-stable@nongnu.org
Reported-by: Harold Gutch <logix@foobar.franken.de>
Fixes: https://bugs.launchpad.net/qemu/+bug/1838658
Fixes: 6864fa3897 ("sun4u: update PCI topology to include simba PCI bridges")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201011081347.2146-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The S24/TCX datasheet is listed as "Unable to locate" on [1].
However the NetBSD revision 1.32 of the driver introduced
64-bit accesses to the stippler and blitter [2]. It is safe
to assume these memory regions are 64-bit accessible.
QEMU implementation is 32-bit, so fill the 'impl' fields.
Michael Lorenz (author of the NetBSD code [2]) provided us with more
information in [3]:
> IIRC the real hardware *requires* 64bit accesses for stipple and
> blitter operations to work. For stipples you write a 64bit word into
> STIP space, the address defines where in the framebuffer you want to
> draw, the data contain a 32bit bitmask, foreground colour and a ROP.
> BLIT space works similarly, the 64bit word contains an offset were to
> read pixels from, and how many you want to copy.
>
> One more thing since there seems to be some confusion - 64bit accesses
> on the framebuffer are fine as well. TCX/S24 is *not* an SBus device,
> even though its node says it is.
> S24 is a card that plugs into a special slot on the SS5 mainboard,
> which is shared with an SBus slot and looks a lot like a horizontal
> UPA slot. Both S24 and TCX are accessed through the Micro/TurboSPARC's
> AFX bus which is 64bit wide and intended for graphics.
> Early FFB docs even mentioned connecting to both AFX and UPA,
> no idea if that was ever realized in hardware though.
[1] http://web.archive.org/web/20111209011516/http://wikis.sun.com/display/FOSSdocs/Home
[2] http://cvsweb.netbsd.org/bsdweb.cgi/src/sys/dev/sbus/tcx.c.diff?r1=1.31&r2=1.32
[3] https://www.mail-archive.com/qemu-devel@nongnu.org/msg734928.html
Cc: qemu-stable@nongnu.org
Reported-by: Andreas Gustafsson <gson@gson.org>
Buglink: https://bugs.launchpad.net/bugs/1892540
Fixes: 55d7bfe229 ("tcx: Implement hardware acceleration")
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Andreas Gustafsson <gson@gson.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201024205100.3623006-1-f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The device should not map itself but instead should be mapped to sysbus by the
sun4u machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead use qdev_set_nic_properties() to configure the on-board NIC at the
sun4m machine level.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Store the child object directly within the sparc32-espdma object rather than
using link properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Store the child object directly within the sparc32-ledma object rather than
using link properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Store the child objects directly within the sparc32-dma object rather than using
link properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200926140216.7368-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
-----BEGIN PGP SIGNATURE-----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=inaF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/led-api-20201026' into staging
API to model LED.
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
# gpg: Signature made Mon 26 Oct 2020 22:03:59 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/led-api-20201026:
hw/arm/tosa: Replace fprintf() calls by LED devices
hw/misc/mps2-scc: Use the LED device
hw/misc/mps2-fpgaio: Use the LED device
hw/arm/aspeed: Add the 3 front LEDs drived by the PCA9552 #1
hw/misc/led: Emit a trace event when LED intensity has changed
hw/misc/led: Allow connecting from GPIO output
hw/misc/led: Add a LED device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRST protocol states that after diagnostics are complete and the
status is posted, we should clear the SRST bit if it should so happen to
be set.
The reset method itself should handle this, but just in case -- make our
intention explicit here.
Signed-off-by: John Snow <jsnow@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20201020200242.1497705-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
We don't need to wait for the falling edge. We can set BSY as
soon as possible and begin immediately resetting the drive. Devices
don't appear to need to take any specific action on the falling edge.
Signed-off-by: John Snow <jsnow@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20201020200242.1497705-3-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Software reset (SRST) should cause the diagnostic command to be run. Make an
explicit call to that routine.
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20201020200242.1497705-2-jsnow@redhat.com
Fixes: 55adb3c456
Fixes: https://bugs.launchpad.net/bugs/1900155
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John Snow <jsnow@redhat.com>
spapr_reallocate_hpt() has three users, two of which pass &error_fatal
and the third one, htab_load(), passes &local_err, uses it to detect
failures and simply propagates -EINVAL up to vmstate_load(), which will
cause QEMU to exit. It is thus confusing that spapr_reallocate_hpt()
doesn't return right away when an error is detected in some cases. Also,
the comment suggesting that the caller is welcome to try to carry on
seems like a remnant in this respect.
This can be improved:
- change spapr_reallocate_hpt() to always report a negative errno on
failure, either as reported by KVM or -ENOSPC if the HPT is smaller
than what was asked,
- use that to detect failures in htab_load() which is preferred over
checking &local_err,
- propagate this negative errno to vmstate_load() because it is more
accurate than propagating -EINVAL for all possible errors.
[dwg: Fix compile error due to omitted prelim patch]
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160371605460.305923.5890143959901241157.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If kvmppc_load_htab_chunk() fails, its return value is propagated up
to vmstate_load(). It should thus be a negative errno, not -1 (which
maps to EPERM and would lure the user into thinking that the problem
is necessarily related to a lack of privilege).
Return the error reported by KVM or ENOSPC in case of short write.
While here, propagate the error message through an @errp argument
and have the caller to print it with error_report_err() instead
of relying on fprintf().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160371604713.305923.5264900354159029580.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Hints should be added with the dedicated error_append_hint() API
because we don't want to print them when using QMP. This requires
to insert ERRP_GUARD as explained in "qapi/error.h".
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160371604030.305923.17464161378167312662.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As recommended in "qapi/error.h", add a bool return value to
spapr_add_lmbs() and spapr_add_nvdimm(), and use them instead
of local_err in spapr_memory_plug().
This allows to get rid of the error propagation overhead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309734178.2739814.3488437759887793902.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Both PC_DIMM_SLOT_PROP and PC_DIMM_ADDR_PROP are defined in the
default property list of the PC DIMM device class:
DEFINE_PROP_UINT64(PC_DIMM_ADDR_PROP, PCDIMMDevice, addr, 0),
DEFINE_PROP_INT32(PC_DIMM_SLOT_PROP, PCDIMMDevice, slot,
PC_DIMM_UNASSIGNED_SLOT),
They should thus be always gettable for both PC DIMMs and NVDIMMs.
An error in getting them can only be the result of a programming
error. It doesn't make much sense to propagate the error in this
case. Abort instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309732180.2739814.7243774674998010907.stgit@bahia.lan>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PC_DIMM_SLOT_PROP property is defined as:
DEFINE_PROP_INT32(PC_DIMM_SLOT_PROP, PCDIMMDevice, slot,
PC_DIMM_UNASSIGNED_SLOT),
Use object_property_get_int() instead of object_property_get_uint().
Since spapr_memory_plug() only gets called if pc_dimm_pre_plug()
succeeded, we expect to have a valid >= 0 slot number, either because
the user passed a valid slot number or because pc_dimm_get_free_slot()
picked one up for us.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309730758.2739814.15821922745424652642.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PC_DIMM_ADDR_PROP property is defined as:
DEFINE_PROP_UINT64(PC_DIMM_ADDR_PROP, PCDIMMDevice, addr, 0),
Use object_property_get_uint() instead of object_property_get_int().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309729609.2739814.4996614957953215591.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
pc_dimm_plug() doesn't use it. It only aborts on error.
Drop @errp and adapt the callers accordingly.
[dwg: Removed unused label to fix compile]
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309728447.2739814.12831204841251148202.stgit@bahia.lan>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the error path of spapr_cpu_core_realize() is just to call
idempotent spapr_cpu_core_unrealize() for rollback, no need to create
and realize the vCPUs in two separate loops.
Merge them and do them same in spapr_cpu_core_unrealize() for symmetry.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160279673321.1808373.2248221100790367912.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_cpu_core_realize() has a rollback path which partially duplicates
the code of spapr_cpu_core_unrealize().
Let's make spapr_cpu_core_unrealize() idempotent and call it instead. This
requires to:
- move the registration and unregistration of the reset handler around
but it is harmless,
- allocate the array of vCPUs with g_new0() to be able to filter out
unused slots,
- make sure to only unrealize vCPUs that have been already realized.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160279672626.1808373.14142129300586424514.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'sc' argument is unused. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160279671929.1808373.10333672533575251075.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since we introduced CPU hot-unplug in sPAPR, we don't unrealize the
vCPU objects explicitly. Instead, we let QOM handle that for us under
object_property_del_all() when the CPU core object is finalized. The
only thing we do is calling cpu_remove_sync() to tear the vCPU thread
down.
This happens to work but it is ugly because:
- we call qdev_realize() but the corresponding qdev_unrealize() is
buried deep in the QOM code
- we call cpu_remove_sync() to undo qemu_init_vcpu() called by
ppc_cpu_realize() in target/ppc/translate_init.c.inc
- the CPU init and teardown paths aren't really symmetrical
The latter didn't bite us so far but a future patch that greatly
simplifies the CPU core realize path needs it to avoid a crash
in QOM.
For all these reasons, have ppc_cpu_unrealize() to undo the changes
of ppc_cpu_realize() by calling cpu_remove_sync() at the right place,
and have the sPAPR CPU core code to call qdev_unrealize().
This requires to add a missing stub because translate_init.c.inc is
also compiled for user mode.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160279671236.1808373.14732005038172874990.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU core is being removed, the machine specific data of each
CPU thread object is leaked.
Fix this by calling the dedicated helper we have for that instead of
simply unparenting the CPU object. Call it from a separate loop in
spapr_cpu_core_unrealize() for symmetry with spapr_cpu_core_realize().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160279670540.1808373.17319746576919615623.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_create_nvdimm_dr_connectors() function doesn't need to access
any internal details of the sPAPR NVDIMM implementation. Also, pretty
much like for the LMBs, only spapr_machine_init() is responsible for the
creation of DR connectors for NVDIMMs.
Make this clear by making this function static in hw/ppc/spapr.c.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160249772183.757627.7396780936543977766.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[dwg] The stack frame itself probably isn't that big a deal, but
avoiding alloca() is generally recommended these days.
Signed-off-by: Elena Afanasova <eafanasova@gmail.com>
Message-Id: <8f07132478469b35fb50a4706691e2b56b10a67b.camel@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we hotplug a CPU during the first second of the kernel boot,
the IRQ can be sent to the kernel while the RTAS event handler
is not installed. The event is queued, but the kernel doesn't
collect it and ignores the new CPU.
As the code relies on edge-triggered IRQ, we can re-assert it
during the event-scan RTAS call if there are still pending
events (as it is already done in check-exception).
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20201015210318.117386-1-lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
DR connector is a device that emulates a firmware abstraction used by PAPR
compliant guests to manage hotplug/dynamic-reconfiguration of PHBs, PCI
devices, memory, and CPUs.
It is internally created by the spapr platform and requires to be owned by
either the machine (PHBs, CPUs, memory) or by a PHB (PCI devices).
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160250199940.765467.6896806997161856576.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The armv7m systick timer is a 24-bit decrementing, wrap-on-zero,
clear-on-write counter. Our current implementation has various
bugs and dubious workarounds in it (for instance see
https://bugs.launchpad.net/qemu/+bug/1872237).
We have an implementation of a simple decrementing counter
and we put a lot of effort into making sure it handles the
interesting corner cases (like "spend a cycle at 0 before
reloading") -- ptimer.
Rewrite the systick timer to use a ptimer rather than
a raw QEMU timer.
Unfortunately this is a migration compatibility break,
which will affect all M-profile boards.
Among other bugs, this fixes
https://bugs.launchpad.net/qemu/+bug/1872237 :
now writes to SYST_CVR when the timer is enabled correctly
do nothing; when the timer is enabled via SYST_CSR.ENABLE,
the ptimer code will (because of POLICY_NO_IMMEDIATE_RELOAD)
arrange that after one timer tick the counter is reloaded
from SYST_RVR and then counts down from there, as the
architecture requires.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201015151829.14656-3-peter.maydell@linaro.org
In ptimer_reload(), we call the callback function provided by the
timer device that is using the ptimer. This callback might disable
the ptimer. The code mostly handles this correctly, except that
we'll still print the warning about "Timer with delta zero,
disabling" if the now-disabled timer happened to be set such that it
would fire again immediately if it were enabled (eg because the
limit/reload value is zero).
Suppress the spurious warning message and the unnecessary
repeat-deletion of the underlying timer in this case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201015151829.14656-2-peter.maydell@linaro.org
Included the newly implemented SBSA generic watchdog device model into
SBSA platform
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201027015927.29495-3-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generic watchdog device model implementation as per ARM SBSA v6.0
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Message-id: 20201027015927.29495-2-shashi.mallela@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the 'uart-out' clock from the CPRMAN to the PL011 instance.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a clock input to the PL011 UART so we can compute the current baud
rate and trace it. This is intended for developers who wish to use QEMU
to e.g. debug their firmware or to figure out the baud rate configured
by an unknown/closed source binary.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Those reset values have been extracted from a Raspberry Pi 3 model B
v1.2, using the 2020-08-20 version of raspios. The dump was done using
the debugfs interface of the CPRMAN driver in Linux (under
'/sys/kernel/debug/clk'). Each exposed clock tree stage (PLLs, channels
and muxes) can be observed by reading the 'regdump' file (e.g.
'plla/regdump').
Those values are set by the Raspberry Pi firmware at boot time (Linux
expects them to be set when it boots up).
Some stages are not exposed by the Linux driver (e.g. the PLL B). For
those, the reset values are unknown and left to 0 which implies a
disabled output.
Once booted in QEMU, the final clock tree is very similar to the one
visible on real hardware. The differences come from some unimplemented
devices for which the driver simply disable the corresponding clock.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This simple mux sits between the PLL channels and the DSI0E and DSI0P
clock muxes. This mux selects between PLLA-DSI0 and PLLD-DSI0 channel
and outputs the selected signal to source number 4 of DSI0E/P clock
muxes. It is controlled by the cm_dsi0hsck register.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A clock mux can be configured to select one of its 10 sources through
the CM_CTL register. It also embeds yet another clock divider, composed
of an integer part and a fractional part. The number of bits of each
part is mux dependent.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The clock multiplexers are the last clock stage in the CPRMAN. Each mux
outputs one clock signal that goes out of the CPRMAN to the SoC
peripherals.
Each mux has at most 10 sources. The sources 0 to 3 are common to all
muxes. They are:
0. ground (no clock signal)
1. the main oscillator (xosc)
2. "test debug 0" clock
3. "test debug 1" clock
Test debug 0 and 1 are actual clock muxes that can be used as sources to
other muxes (for debug purpose).
Sources 4 to 9 are mux specific and can be unpopulated (grounded). Those
sources are fed by the PLL channels outputs.
One corner case exists for DSI0E and DSI0P muxes. They have their source
number 4 connected to an intermediate multiplexer that can select
between PLLA-DSI0 and PLLD-DSI0 channel. This multiplexer is called
DSI0HSCK and is not a clock mux as such. It is really a simple mux from
the hardware point of view (see https://elinux.org/The_Undocumented_Pi).
This mux is not implemented in this commit.
Note that there is some muxes for which sources are unknown (because of
a lack of documentation). For those cases all the sources are connected
to ground in this implementation.
Each clock mux output is exported by the CPRMAN at the qdev level,
adding the suffix '-out' to the mux name to form the output clock name.
(E.g. the 'uart' mux sees its output exported as 'uart-out' at the
CPRMAN level.)
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A PLL channel is able to further divide the generated PLL frequency.
The divider is given in the CTRL_A2W register. Some channels have an
additional fixed divider which is always applied to the signal.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PLLs are composed of multiple channels. Each channel outputs one clock
signal. They are modeled as one device taking the PLL generated clock as
input, and outputting a new clock.
A channel shares the CM register with its parent PLL, and has its own
A2W_CTRL register. A write to the CM register will trigger an update of
the PLL and all its channels, while a write to an A2W_CTRL channel
register will update the required channel only.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN PLLs generate a clock based on a prescaler, a multiplier and
a divider. The prescaler doubles the parent (xosc) frequency, then the
multiplier/divider are applied. The multiplier has an integer and a
fractional part.
This commit also implements the CPRMAN CM_LOCK register. This register
reports which PLL is currently locked. We consider a PLL has being
locked as soon as it is enabled (on real hardware, there is a delay
after turning a PLL on, for it to stabilize).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are 5 PLLs in the CPRMAN, namely PLL A, C, D, H and B. All of them
take the xosc clock as input and produce a new clock.
This commit adds a skeleton implementation for the PLLs as sub-devices
of the CPRMAN. The PLLs are instantiated and connected internally to the
main oscillator.
Each PLL has 6 registers : CM, A2W_CTRL, A2W_ANA[0,1,2,3], A2W_FRAC. A
write to any of them triggers a call to the (not yet implemented)
pll_update function.
If the main oscillator changes frequency, an update is also triggered.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell