The value from twoD_foreground (which is in host endian format) must
be converted to the endianness of the framebuffer (currently always
little endian) before it can be used to perform the fill operation.
Signed-off-by: Marcus Comstedt <marcus@mc.pp.se>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
So that we don't have to call qdev_get_machine() to get the machine
class and the sPAPRIrq backend holding the number of MSIs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The new layout using static IRQ number does not leave much space to
the dynamic MSI range, only 0x100 IRQ numbers. Increase the total
number of IRQS for newer machines and introduce a legacy XICS backend
for pre-3.1 machines to maintain compatibility.
For the old backend, provide a 'nr_msis' value covering the full IRQ
number space as it does not use the bitmap allocator to allocate MSI
interrupt numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The number of MSI interrupts a sPAPR machine can allocate is in direct
relation with the number of interrupts of the sPAPRIrq backend. Define
statically this value at the sPAPRIrq class level and use it for the
"ibm,pe-total-#msi" property of the sPAPR PHB.
According to the PAPR specs, "ibm,pe-total-#msi" defines the maximum
number of MSIs that are available to the PE. We choose to advertise
the maximum number of MSIs that are available to the machine for
simplicity of the model and to avoid segmenting the MSI interrupt pool
which can be easily shared. If the pool limit is reached, it can be
extended dynamically.
Finally, remove XICS_IRQS_SPAPR which is now unused.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the PReP specification section 6.1.6 "System Interrupt
Assignments", all PCI interrupts are routed via IRQ 15.
Instead of mapping each PCI IRQ separately, we introduce an OR gate within the
raven PCI host bridge and then wire the single output of the OR gate to the
interrupt controller.
Note that whilst the (now deprecated) PReP machine still exists we still need
to preserve the old IRQ routing. This is done by adding a new "is-legacy-prep"
property to the raven PCI host bridge which is set to true for the PReP
machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This really lays the groundwork for the upcoming patches: it renames the
irqs PREPPCIState struct member to pci_irqs (as soon there will be a
distinction) and then changes the raven IRQ opaque to use PREPPCIState
instead of just irqs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
OpenBIOS gained 40p support in 5b20e4cace
Use it, instead of relying on an unmaintained and very limited firmware.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
-----BEGIN PGP SIGNATURE-----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=WnE4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.1-20180907' into staging
ppc patch queue 2018-09-07
Here's another pull request for qemu-3.1. No real theme here, just an
assortment of various fixes. Probably the most notable thing is the
removal of the ppcemb target which has been deprecated for some time
now.
# gpg: Signature made Fri 07 Sep 2018 08:30:02 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.1-20180907:
target-ppc: Extend HWCAP2 bits for ISA 3.0
target/ppc/kvm: set vcpu as online/offline
Fix a deadlock case in the CPU hotplug flow
spapr: Correct reference count on spapr-cpu-core
mac_newworld: implement custom FWPathProvider
uninorth: add ofw-addr property to allow correct fw path generation
mac_oldworld: implement custom FWPathProvider
grackle: set device fw_name and address for correct fw path generation
macio: add addr property to macio IDE object
macio: add macio bus to help with fw path generation
macio: move MACIOIDEState type declarations to macio.h
spapr_pci: fix potential NULL pointer dereference
spapr: fix leak of rev array
ppc: Remove deprecated ppcemb target
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAluQU38ACgkQIeENKd+X
cFRAXQgAlhNcwby+Jsk8sbLajMWXEtww9FIv+XESldPOJHmJyCkNDVZX8MuMM7+f
8NraD3YGDJvXP/BEcmyE5yPC6mx+OIi8ufzqP0rUML1x4+Tpxp8nZ7sBH197RtGg
eImPA6oKvg4wyfNOrZ+hGa8HF/iMT03TqeKggUPf3dVAs8LV2iUwBIzrRLB4IhIN
yFnhbcw8cW04tWUhYg4+viDY2k0q7fMrJZkASD/RjGMBjubJkwWvSYOdMIEWSpcG
2qLT5SohzUzHyKPONsoBKjSIP+nKgtyYR6IJh40FDd5S5RRMHe/n3q9jChIkHMma
x1eSNvVd41++QlBKqDeAlA+gbdK/uw==
=FJn/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-pullreq-20180905' into staging
A misc collection of RISC-V related patches for 3.1.
# gpg: Signature made Wed 05 Sep 2018 23:06:55 BST
# gpg: using RSA key 21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-pullreq-20180905:
riscv: remove define cpu_init()
hw/riscv/spike: Set the soc device tree node as a simple-bus
hw/riscv/virtio: Set the soc device tree node as a simple-bus
target/riscv: call gen_goto_tb on DISAS_TOO_MANY
target/riscv: optimize indirect branches
target/riscv: optimize cross-page direct jumps in softmmu
RISC-V: Simplify riscv_cpu_local_irqs_pending
RISC-V: Use atomic_cmpxchg to update PLIC bitmaps
RISC-V: Improve page table walker spec compliance
RISC-V: Update address bits to support sv39 and sv48
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- split off the individual virtio-ccw devices into separate files
-----BEGIN PGP SIGNATURE-----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=c1n9
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180829' into staging
- various fixes and improvements in the tcg code
- split off the individual virtio-ccw devices into separate files
# gpg: Signature made Wed 29 Aug 2018 10:38:03 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180829:
target/s390x: use regular spaces in translate.c
hw/s390x: Move virtio-ccw-blk code to a separate file
hw/s390x: Move virtio-ccw-net code to a separate file
hw/s390x: Move virtio-ccw-input code to a separate file
hw/s390x: Move virtio-ccw-gpu code to a separate file
hw/s390x: Move vhost-vsock-ccw code to a separate file
hw/s390x: Move virtio-ccw-crypto code to a separate file
hw/s390x: Move virtio-ccw-9p code to a separate file
hw/s390x: Move virtio-ccw-rng code to a separate file
hw/s390x: Move virtio-ccw-scsi code to a separate file
hw/s390x: Move virtio-ccw-balloon code to a separate file
hw/s390x: Move virtio-ccw-serial code to a separate file
hw/s390x/virtio-ccw: Consolidate calls to virtio_ccw_unrealize()
target/s390x: fix PACK reading 1 byte less and writing 1 byte more
target/s390x: add EX support for TRT and TRTR
target/s390x: fix IPM polluting irrelevant bits
target/s390x: fix CSST decoding and runtime alignment check
target/s390x: add BAL and BALR instructions
tests/tcg: add a simple s390x test
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To allow Linux to enumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Set the newly added register(KVM_REG_PPC_ONLINE) to indicate if the vcpu is
online(1) or offline(0)
KVM will use this information to set the RWMR register, which controls the PURR
and SPURR accumulation.
CC: paulus@samba.org
Signed-off-by: Nikunj A Dadhania <nikunj@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Switch from cpu_physical_memory_map to dma_memory_map,
so iommu mappings for virtio-gpu objects work properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180829122101.29852-3-kraxel@redhat.com>
No functional change, just preparation for a followup patch
which needs a VirtIOGPU pointer.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20180829122101.29852-2-kraxel@redhat.com>
We need to set cs->halted to 1 before calling ppc_set_compat. The reason
is that ppc_set_compat kicks up the new thread created to manage the
hotplugged KVM virtual CPU and the code drives directly to KVM_RUN
ioctl. When cs->halted is 1, the code:
int kvm_cpu_exec(CPUState *cpu)
...
if (kvm_arch_process_async_events(cpu)) {
atomic_set(&cpu->exit_request, 0);
return EXCP_HLT;
}
...
returns before it reaches KVM_RUN, giving time to the main thread to
finish its job. Otherwise we can fall in a deadlock because the KVM
thread will issue the KVM_RUN ioctl while the main thread is setting up
KVM registers. Depending on how these jobs are scheduled we'll end up
freezing QEMU.
The following output shows kvm_vcpu_ioctl sleeping because it cannot get
the mutex and never will.
PS: kvm_vcpu_ioctl was triggered kvm_set_one_reg - compat_pvr.
STATE: TASK_UNINTERRUPTIBLE|TASK_WAKEKILL
PID: 61564 TASK: c000003e981e0780 CPU: 48 COMMAND: "qemu-system-ppc"
#0 [c000003e982679a0] __schedule at c000000000b10a44
#1 [c000003e98267a60] schedule at c000000000b113a8
#2 [c000003e98267a90] schedule_preempt_disabled at c000000000b11910
#3 [c000003e98267ab0] __mutex_lock at c000000000b132ec
#4 [c000003e98267bc0] kvm_vcpu_ioctl at c00800000ea03140 [kvm]
#5 [c000003e98267d20] do_vfs_ioctl at c000000000407d30
#6 [c000003e98267dc0] ksys_ioctl at c000000000408674
#7 [c000003e98267e10] sys_ioctl at c0000000004086f8
#8 [c000003e98267e30] system_call at c00000000000b488
crash> struct -x kvm.vcpus 0xc000003da0000000
vcpus = {0xc000003db4880000, 0xc000003d52b80000, 0xc0000039e9c80000, 0xc000003d0e200000, 0xc000003d58280000, 0x0, 0x0, ...}
crash> struct -x kvm_vcpu.mutex.owner 0xc000003d58280000
mutex.owner = {
counter = 0xc000003a23a5c881 <- flag 1: waiters
},
crash> bt 0xc000003a23a5c880
PID: 61579 TASK: c000003a23a5c880 CPU: 9 COMMAND: "CPU 4/KVM"
(active)
crash> struct -x kvm_vcpu.mutex.wait_list 0xc000003d58280000
mutex.wait_list = {
next = 0xc000003e98267b10,
prev = 0xc000003e98267b10
},
crash> struct -x mutex_waiter.task 0xc000003e98267b10
task = 0xc000003e981e0780
The following command-line was used to reproduce the problem (note: gdb
and trace can change the results).
$ qemu-ppc/build/ppc64-softmmu/qemu-system-ppc64 -cpu host \
-enable-kvm -m 4096 \
-smp 4,maxcpus=8,sockets=1,cores=2,threads=4 \
-display none -nographic \
-drive file=disk1.qcow2,format=qcow2
...
(qemu) device_add host-spapr-cpu-core,core-id=4
[no interaction is possible after it, only SIGKILL to take the terminal
back]
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This reverts commit 93f874fe9d.
Now with virtio-vga being resetted properly the
crash workaround is not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-3-kraxel@redhat.com
We must call the reset functions for both virtio-gpu
and vga to properly reset the combo device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180821111313.27792-2-kraxel@redhat.com
spapr_init_cpus() currently creates spapr-cpu-core objects via
object_new() and setting their realized property to true. This leaves
their reference count at two, because object_new() adds an initial
reference and the realization attaches them to a default parent object
which also increments the reference count.
This causes a problem if one of these cores is hot unplugged: no
delete event is generated for it because it's reference count doesn't
reach zero when it is detached from it's parent.
Correct this by adding a call to object_unref() in spapr_init_cpus().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
since an additional disk node should not be added except for virtio devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the correct generation of bootdevice fw paths for in-built IDE
and virtio-pci-blk devices suitable for OpenBIOS.
Note we also set the MachineClass ignore_boot_device_suffixes property to true
since an additional disk node should not be added except for virtio devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This contains the offset of the IDE controller within the macio address space
and is required to allow the address to be included within the fw path.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As the in-built IDE controller is attached to the macio bus then we should also
model this the same in QEMU to aid fw path generation.
Note that all existing macio devices are moved onto the new macio bus so that
the qdev tree accurately reflects the real hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The generated qapi_event_send_FOO() take an Error ** argument. They
can't actually fail, because all they do with the argument is passing it
to functions that can't fail: the QObject output visitor, and the
@qmp_emit callback, which is either monitor_qapi_event_queue() or
event_test_emit().
Drop the argument, and pass &error_abort to the QObject output visitor
and @qmp_emit instead.
Suggested-by: Eric Blake <eblake@redhat.com>
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815133747.25032-4-peterx@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message rewritten, update to qapi-code-gen.txt corrected]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_BLK has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532542110-9017-1-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_NET has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532542056-8927-1-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_INPUT has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-11-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_GPU has been set. This
can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-10-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VHOST_VSOCK has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-9-git-send-email-thuth@redhat.com>
[CH: updated MAINTAINERS]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_CRYPTO has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-8-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_9P and CONFIG_VIRTFS
have been set. This can be done best if the code resides in a separate
file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-7-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_RNG has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-6-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_SCSI has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-5-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_BALLOON has been
set. This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-4-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The code should only be enabled if CONFIG_VIRTIO_SERIAL has been set.
This can be done best if the code resides in a separate file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-3-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Currently, every virtio-ccw device explicitely sets its unrealize
function to virtio_ccw_unrealize() in its class_init function.
We can simplify this by using a common unrealize function, just like
it is already done for the realize functions.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1532521224-27235-2-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 2c88b098e7 added a call to SPAPR_MACHINE_GET_CLASS(spapr) in
spapr_phb_realize() before we check spapr isn't NULL. This causes QEMU
to crash when starting a non-pseries machine with a sPAPR PHB.
This could be fixed by setting the smc variable after the null check,
but it seems more explicit to use a ternary operator to skip the call
to SPAPR_MACHINE_GET_CLASS() if spapr is NULL, since spapr_phb_realize()
will return immediately in this case.
This was reported by Coverity (CID 1395170 and 1395183).
Fixes: 2c88b098e7
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduced in 04d595b300 ("spapr: do not use CPU_FOREACH_REVERSE",
2018-08-23)
Fixes: CID1395181
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no known available OS for ppc around anymore that uses page
sizes below 4k, so it does not make much sense that we keep wasting
our time on building and testing the ppcemb-softmmu target. It has
been deprecated since two releases, and nobody complained, so let's
remove this now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace all the trace_vtd_err_*() hooks with the new error_report_once()
since they are similar to trace_vtd_err() - dumping the first error
would be mostly enough, then we have them on by default too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-4-peterx@redhat.com>
[Use "%x" instead of "%" PRIx16 to print uint16_t, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Replace existing trace_vtd_err() with error_report_once() then stderr
will capture something if any of the error happens, meanwhile we don't
suffer from any DDOS. Then remove the trace point. Since at it,
provide more information where proper (now we can pass parameters into
the report function).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180815095328.32414-3-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[Two format strings fixed, whitespace tidied up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix passing argument for nanoMIPS bare metal related to the
semihosting regime.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Setup the GT64120 BARs in the nanoMIPS bootloader, in the same way that
they are setup in the MIPS32 bootloader. This is necessary for Linux to
be able to access peripherals, including the UART.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Paul Burton <pburton@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Marcus Comstedt