This fixes compress with colo.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
So make everything that uses it uint64_t no int64_t.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20230504113841.23130-2-quintela@redhat.com>
migration_stats is just too long, and it is going to have more than
ram counters in the near future.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
There is already include/qemu/stats.h, so stats.h was a bad idea.
We want this file to not depend on anything else, we will move all the
migration counters/stats to this struct.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
As we set its value, it needs to be operated with atomics.
We rename it from remaining to better reflect its meaning.
Statistics always return the real reamaining bytes. This was used to
store how much pages where dirty on the previous generation, so we can
calculate the expected downtime as: dirty_bytes_last_sync /
current_bandwith.
If we use the actual remaining bytes, we would see a very small value
at the end of the iteration.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
I am open to use ram_bytes_remaining() in its only use and be more
"optimistic" about the downtime.
Don't use __nocheck() functions.
Use stat64_get() now that it exists.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
---
Don't use __nocheck() variants
Use stat64_get()
This makes the function more regular with everything else.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once there, make it more regular and remove the need for
MigrationState parameter.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once there, rename it to migrate_tls() and make it return bool for
consistency.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
---
Fix typos found by fabiano
To be consistent with every other parameter, rename to
migrate_block_incremental().
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to migrate_return_path()
to be consistent with all other capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to migrate_block()
to be consistent with all other capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to migrate_xbzrle()
to be consistent with all other capabilities.
We change the type to return bool also for consistency.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to
migrate_zero_copy_send() to be consistent with all other capabilities.
We can remove the CONFIG_LINUX guard. We already check that we can't
setup this capability in migrate_caps_check().
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to migrate_multifd()
to be consistent with all other capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to migrate_events()
to be consistent with all other capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to migrate_compress()
to be consistent with all other capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Once that we are there, we rename the function to migrate_colo() to be
consistent with all other capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
We move there all capabilities helpers from migration.c.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
---
Following David advise:
- looked through the history, capabilities are newer than 2012, so we
can remove that bit of the header.
- This part is posterior to Anthony.
Original Author is Orit. Once there,
I put myself. Peter Xu also did quite a bit of work here.
Anyone else wants/needs to be there? I didn't search too hard
because nobody asked before to be added.
What do you think?
And remove the convoluted use of qmp_migrate_set_capabilities() to
enable disable MIGRATION_CAPABILITY_BLOCK.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
It has nothing to do with migration, except for the "migrate" in the
name of the command. Move it with the rest of the ui commands.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
It is only used there, so we can make it static.
Once there, remove spice.h that it is not used.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
---
fix David Edmonson ui/qemu-spice.h unintended removal
No need to declare a temporary variable.
Suggested-by: Juan Quintela <quintela@redhat.com>
Fixes: 1df36e8c6289 ("migration: Handle block device inactivation failures better")
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We used to pass the old capabilities array and the new
capabilities as a list.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
It is clear from the context what that means, and such a long name
with the extra long names of the capabilities make very difficilut to
stay inside the 80 columns limit.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Consider what happens when performing a migration between two host
machines connected to an NFS server serving multiple block devices to
the guest, when the NFS server becomes unavailable. The migration
attempts to inactivate all block devices on the source (a necessary
step before the destination can take over); but if the NFS server is
non-responsive, the attempt to inactivate can itself fail. When that
happens, the destination fails to get the migrated guest (good,
because the source wasn't able to flush everything properly):
(qemu) qemu-kvm: load of migration failed: Input/output error
at which point, our only hope for the guest is for the source to take
back control. With the current code base, the host outputs a message, but then appears to resume:
(qemu) qemu-kvm: qemu_savevm_state_complete_precopy_non_iterable: bdrv_inactivate_all() failed (-1)
(src qemu)info status
VM status: running
but a second migration attempt now asserts:
(src qemu) qemu-kvm: ../block.c:6738: int bdrv_inactivate_recurse(BlockDriverState *): Assertion `!(bs->open_flags & BDRV_O_INACTIVE)' failed.
Whether the guest is recoverable on the source after the first failure
is debatable, but what we do not want is to have qemu itself fail due
to an assertion. It looks like the problem is as follows:
In migration.c:migration_completion(), the source sets 'inactivate' to
true (since COLO is not enabled), then tries
savevm.c:qemu_savevm_state_complete_precopy() with a request to
inactivate block devices. In turn, this calls
block.c:bdrv_inactivate_all(), which fails when flushing runs up
against the non-responsive NFS server. With savevm failing, we are
now left in a state where some, but not all, of the block devices have
been inactivated; but migration_completion() then jumps to 'fail'
rather than 'fail_invalidate' and skips an attempt to reclaim those
those disks by calling bdrv_activate_all(). Even if we do attempt to
reclaim disks, we aren't taking note of failure there, either.
Thus, we have reached a state where the migration engine has forgotten
all state about whether a block device is inactive, because we did not
set s->block_inactive in enough places; so migration allows the source
to reach vm_start() and resume execution, violating the block layer
invariant that the guest CPUs should not be restarted while a device
is inactive. Note that the code in migration.c:migrate_fd_cancel()
will also try to reactivate all block devices if s->block_inactive was
set, but because we failed to set that flag after the first failure,
the source assumes it has reclaimed all devices, even though it still
has remaining inactivated devices and does not try again. Normally,
qmp_cont() will also try to reactivate all disks (or correctly fail if
the disks are not reclaimable because NFS is not yet back up), but the
auto-resumption of the source after a migration failure does not go
through qmp_cont(). And because we have left the block layer in an
inconsistent state with devices still inactivated, the later migration
attempt is hitting the assertion failure.
Since it is important to not resume the source with inactive disks,
this patch marks s->block_inactive before attempting inactivation,
rather than after succeeding, in order to prevent any vm_start() until
it has successfully reactivated all devices.
See also https://bugzilla.redhat.com/show_bug.cgi?id=2058982
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Lukas Straub <lukasstraub2@web.de>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Rest of counters that refer to pages has a _pages suffix.
And historically, this showed the number of full pages transferred.
The name "normal" refered to the fact that they were sent without any
optimization (compression, xbzrle, zero_page, ...).
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Rest of counters that refer to pages has a _pages suffix.
And historically, this showed the number of pages composed of the same
character, here comes the name "duplicated". But since years ago, it
refers to the number of zero_pages.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
In the spirit of:
commit 394d323bc3451e4d07f13341cb8817fac8dfbadd
Author: Peter Xu <peterx@redhat.com>
Date: Tue Oct 11 17:55:51 2022 -0400
migration: Use atomic ops properly for page accountings
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Using MgrationStats as type for ram_counters mean that we didn't have
to re-declare each value in another struct. The need of atomic
counters have make us to create MigrationAtomicStats for this atomic
counters.
Create RAMStats type which is a merge of MigrationStats and
MigrationAtomicStats removing unused members.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
---
Fix typos found by David Edmondson
In 8.0 devel window we reworked preempt channel creation, so that there'll
be no race condition when the migration channel and preempt channel got
established in the wrong order in commit 5655aab079.
However no one noticed that the change will also be not compatible with
older qemus, majorly 7.1/7.2 versions where preempt mode started to be
supported.
Leverage the same pre-7.2 flag introduced in the previous patch to recover
the behavior hopefully before 8.0 releases, so we don't break migration
when we migrate from 8.0 to older qemu binaries.
Fixes: 5655aab079 ("migration: Postpone postcopy preempt channel to be after main")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
postcopy_qemufile_src object should be owned by one thread, either the main
thread (e.g. when at the beginning, or at the end of migration), or by the
return path thread (when during a preempt enabled postcopy migration). If
that's not the case the access to the object might be racy.
postcopy_preempt_shutdown_file() can be potentially racy, because it's
called at the end phase of migration on the main thread, however during
which the return path thread hasn't yet been recycled; the recycle happens
in await_return_path_close_on_source() which is after this point.
It means, logically it's posslbe the main thread and the return path thread
are both operating on the same qemufile. While I don't think qemufile is
thread safe at all.
postcopy_preempt_shutdown_file() used to be needed because that's where we
send EOS to dest so that dest can safely shutdown the preempt thread.
To avoid the possible race, remove this only place that a race can happen.
Instead we figure out another way to safely close the preempt thread on
dest.
The core idea during postcopy on deciding "when to stop" is that dest will
send a postcopy SHUT message to src, telling src that all data is there.
Hence to shut the dest preempt thread maybe better to do it directly on
dest node.
This patch proposed such a way that we change postcopy_prio_thread_created
into PreemptThreadStatus, so that we kick the preempt thread on dest qemu
by a sequence of:
mis->preempt_thread_status = PREEMPT_THREAD_QUIT;
qemu_file_shutdown(mis->postcopy_qemufile_dst);
While here shutdown() is probably so far the easiest way to kick preempt
thread from a blocked qemu_get_be64(). Then it reads preempt_thread_status
to make sure it's not a network failure but a willingness to quit the
thread.
We could have avoided that extra status but just rely on migration status.
The problem is postcopy_ram_incoming_cleanup() is just called early enough
so we're still during POSTCOPY_ACTIVE no matter what.. So just make it
simple to have the status introduced.
One flag x-preempt-pre-7-2 is added to keep old pre-7.2 behaviors of
postcopy preempt.
Fixes: 9358982744 ("migration: Send requested page directly in rp-return thread")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Once that res_compatible is removed, they don't make sense anymore.
We remove the _only preffix. And to make things clearer we rename
them to must_precopy and can_postcopy.
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Nothing assigns to it after previous commit.
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Currently running migration_incoming_state_destroy() without first running
multifd_load_cleanup() will cause a yank error:
qemu-system-x86_64: ../util/yank.c:107: yank_unregister_instance:
Assertion `QLIST_EMPTY(&entry->yankfns)' failed.
(core dumped)
The above error happens in the target host, when multifd is being used
for precopy, and then postcopy is triggered and the migration finishes.
This will crash the VM in the target host.
To avoid that, move multifd_load_cleanup() inside
migration_incoming_state_destroy(), so that the load cleanup becomes part
of the incoming state destroying process.
Running multifd_load_cleanup() twice can become an issue, though, but the
only scenario it could be ran twice is on process_incoming_migration_bh().
So removing this extra call is necessary.
On the other hand, this multifd_load_cleanup() call happens way before the
migration_incoming_state_destroy() and having this happening before
dirty_bitmap_mig_before_vm_start() and vm_start() may be a need.
So introduce a new function multifd_load_shutdown() that will mainly stop
all multifd threads and close their QIOChannels. Then use this function
instead of multifd_load_cleanup() to make sure nothing else is received
before dirty_bitmap_mig_before_vm_start().
Fixes: b5eea99ec2 ("migration: Add yank feature")
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since it's introduction in commit f986c3d256 ("migration: Create multifd
migration threads"), multifd_load_cleanup() never returned any value
different than 0, neither set up any error on errp.
Even though, on process_incoming_migration_bh() an if clause uses it's
return value to decide on setting autostart = false, which will never
happen.
In order to simplify the codebase, change multifd_load_cleanup() signature
to 'void multifd_load_cleanup(void)', and for every usage remove error
handling or decision made based on return value != 0.
Fixes: b5eea99ec2 ("migration: Add yank feature")
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Postcopy with preempt-mode enabled needs two channels to communicate. The
order of channel establishment is not guaranteed. It can happen that the
dest QEMU got the preempt channel connection request before the main
channel is established, then the migration may make no progress even during
precopy due to the wrong order.
To fix it, create the preempt channel only if we know the main channel is
established.
For a general postcopy migration, we delay it until postcopy_start(),
that's where we already went through some part of precopy on the main
channel. To make sure dest QEMU has already established the channel, we
wait until we got the first PONG received. That's something we do at the
start of precopy when postcopy enabled so it's guaranteed to happen sooner
or later.
For a postcopy recovery, we delay it to qemu_savevm_state_resume_prepare()
where we'll have round trips of data on bitmap synchronizations, which
means the main channel must have been established.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This is mostly useless, but useful for us to know whether the main channel
is correctly established without changing the migration protocol.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since we just dropped the only case where postcopy_preempt_setup() can
return an error, it doesn't need a retval anymore because it never fails.
Move the preempt check to the caller, preparing it to be used elsewhere to
do nothing but as simple as kicking the async connection.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The whole idea of multi-channel checks was not properly done, IMHO.
Currently we check multi-channel in a lot of places, but actually that's
not needed because we only need to check it right after we get the URI and
that should be it.
If the URI check succeeded, we should never need to check it again because
we must have it. If it check fails, we should fail immediately on either
the qmp_migrate or qmp_migrate_incoming, instead of failingg it later after
the connection established.
Neither should we fail any set capabiliities like what we used to do here:
5ad15e8614 ("migration: allow enabling mutilfd for specific protocol only", 2021-10-19)
Because logically the URI will only be set later after the capability is
set, so it doesn't make a lot of sense to check the URI type when setting
the capability, because we're checking the cap with an old URI passed in,
and that may not even be the URI we're going to use later.
This patch mostly reverted all such checks for before, dropping the
variable migrate_allow_multi_channels and helpers. Instead, add a common
helper to check URI for multi-channels for either qmp_migrate and
qmp_migrate_incoming and that should do all the proper checks. The failure
will only trigger with the "migrate" or "migrate_incoming" command, or when
user specified "-incoming xxx" where "xxx" is not "defer".
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To support query migration thread infomation, save and delete
thread(live_migration and multifdsend) information at thread
creation and finish.
Signed-off-by: Jiang Jiacheng <jiangjiacheng@huawei.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Current logic assumes that channel connections on the destination side are
always established in the same order as the source and the first one will
always be the main channel followed by the multifid or post-copy
preemption channel. This may not be always true, as even if a channel has a
connection established on the source side it can be in the pending state on
the destination side and a newer connection can be established first.
Basically causing out of order mapping of channels on the destination side.
Currently, all channels except post-copy preempt send a magic number, this
patch uses that magic number to decide the type of channel. This logic is
applicable only for precopy(multifd) live migration, as mentioned, the
post-copy preempt channel does not send any magic number. Also, tls live
migrations already does tls handshake before creating other channels, so
this issue is not possible with tls, hence this logic is avoided for tls
live migrations. This patch uses read peek to check the magic number of
channels so that current data/control stream management remains
un-effected.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: manish.mishra <manish.mishra@nutanix.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The downtime should be displayed during postcopy phase because the
switchover phase is done. OTOH it's weird to show "expected downtime"
which can confuse what does that mean if the switchover has already
happened anyway.
This is a slight ABI change on QMP, but I assume it shouldn't affect
anyone.
Reviewed-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Let's factor out this check, to be used in virtio-mem context next.
While at it, fix a spelling error in a related comment.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>S
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
... and store it in the migration state. This is a preparation for
storing selected vmds's already in qemu_savevm_state_setup().
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Until previous commit, save_live_pending() was used for ram. Now with
the split into state_pending_estimate() and state_pending_exact() it
is not needed anymore, so remove them.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We split the function into to:
- state_pending_estimate: We estimate the remaining state size without
stopping the machine.
- state pending_exact: We calculate the exact amount of remaining
state.
The only "device" that implements different functions for _estimate()
and _exact() is ram.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This moves the command from MAINTAINERS sections "Human Monitor (HMP)"
and "QMP" to "Migration".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20230124121946.1139465-19-armbru@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Hi
This are the patches that I had to drop form the last PULL request because they werent fixes:
- AVX2 is dropped, intel posted a fix, I have to redo it
- Fix for out of order channels is out
Daniel nacked it and I need to redo it
-----BEGIN PGP SIGNATURE-----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=zGNB
-----END PGP SIGNATURE-----
Merge tag 'next-8.0-pull-request' of https://gitlab.com/juan.quintela/qemu into staging
Migration patches for 8.0
Hi
This are the patches that I had to drop form the last PULL request because they werent fixes:
- AVX2 is dropped, intel posted a fix, I have to redo it
- Fix for out of order channels is out
Daniel nacked it and I need to redo it
# gpg: Signature made Thu 15 Dec 2022 09:38:29 GMT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'next-8.0-pull-request' of https://gitlab.com/juan.quintela/qemu:
migration: Drop rs->f
migration: Remove old preempt code around state maintainance
migration: Send requested page directly in rp-return thread
migration: Move last_sent_block into PageSearchStatus
migration: Make PageSearchStatus part of RAMState
migration: Add pss_init()
migration: Introduce pss_channel
migration: Teach PSS about host page
migration: Use atomic ops properly for page accountings
migration: Yield bitmap_mutex properly when sending/sleeping
migration: Remove RAMState.f references in compression code
migration: Trivial cleanup save_page_header() on same block check
migration: Cleanup xbzrle zero page cache update logic
migration: Add postcopy_preempt_active()
migration: Take bitmap mutex when completing ram migration
migration: Export ram_release_page()
migration: Export ram_transferred_ram()
multifd: Create page_count fields into both MultiFD{Recv,Send}Params
multifd: Create page_size fields into both MultiFD{Recv,Send}Params
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the new code to send pages in rp-return thread, there's little help to
keep lots of the old code on maintaining the preempt state in migration
thread, because the new way should always be faster..
Then if we'll always send pages in the rp-return thread anyway, we don't
need those logic to maintain preempt state anymore because now we serialize
things using the mutex directly instead of using those fields.
It's very unfortunate to have those code for a short period, but that's
still one intermediate step that we noticed the next bottleneck on the
migration thread. Now what we can do best is to drop unnecessary code as
long as the new code is stable to reduce the burden. It's actually a good
thing because the new "sending page in rp-return thread" model is (IMHO)
even cleaner and with better performance.
Remove the old code that was responsible for maintaining preempt states, at
the meantime also remove x-postcopy-preempt-break-huge parameter because
with concurrent sender threads we don't really need to break-huge anymore.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
With all the facilities ready, send the requested page directly in the
rp-return thread rather than queuing it in the request queue, if and only
if postcopy preempt is enabled. It can achieve so because it uses separate
channel for sending urgent pages. The only shared data is bitmap and it's
protected by the bitmap_mutex.
Note that since we're moving the ownership of the urgent channel from the
migration thread to rp thread it also means the rp thread is responsible
for managing the qemufile, e.g. properly close it when pausing migration
happens. For this, let migration_release_from_dst_file to cover shutdown
of the urgent channel too, renaming it as migration_release_dst_files() to
better show what it does.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To prepare for thread-safety on page accountings, at least below counters
need to be accessed only atomically, they are:
ram_counters.transferred
ram_counters.duplicate
ram_counters.normal
ram_counters.postcopy_bytes
There are a lot of other counters but they won't be accessed outside
migration thread, then they're still safe to be accessed without atomic
ops.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/migration.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-17-armbru@redhat.com>
Multifd thread model does not work for compression, explicitly disable it.
Note that previuosly even we can enable both of them, nothing will go
wrong, because the compression code has higher priority so multifd feature
will just be ignored. Now we'll fail even earlier at config time so the
user should be aware of the consequence better.
Note that there can be a slight chance of breaking existing users, but
let's assume they're not majority and not serious users, or they should
have found that multifd is not working already.
With that, we can safely drop the check in ram_save_target_page() for using
multifd, because when multifd=on then compression=off, then the removed
check on save_page_use_compression() will also always return false too.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The preempt mode requires the capability to assign channel for each of the
page, while the compression logic will currently assign pages to different
compress thread/local-channel so potentially they're incompatible.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Callers of coroutine_fn must be coroutine_fn themselves, or the call
must be within "if (qemu_in_coroutine())". Apply coroutine_fn to
functions where this holds.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Faria <afaria@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220922084924.201610-26-pbonzini@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Coverity complains that when we use the return value from
migrate_multifd_compression() as an array index:
multifd_recv_state->ops = multifd_ops[migrate_multifd_compression()];
that this might overrun the array (which is declared to have size
MULTIFD_COMPRESSION__MAX). This is because the function return type
is MultiFDCompression, which is an autogenerated enum. The code
generator includes the "one greater than the maximum possible value"
MULTIFD_COMPRESSION__MAX in the enum, even though this is not
actually a valid value for the enum, and this makes Coverity think
that migrate_multifd_compression() could return that __MAX value and
index off the end of the array.
Suppress the Coverity error by asserting that the value we're going
to return is within range.
Resolves: Coverity CID 1487239, 1487254
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220721115207.729615-2-peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Some of params->has_* = true are missing in migration_instance_init, this
causes migrate_params_check() to skip some tests, allowing some
unsupported scenarios.
Fix this by adding all missing params->has_* = true in
migration_instance_init().
Fixes: 69ef1f36b0 ("migration: define 'tls-creds' and 'tls-hostname' migration parameters")
Fixes: 1d58872a91 ("migration: do not wait for free thread")
Fixes: d2f1d29b95 ("migration: add support for a "tls-authz" migration parameter")
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Message-Id: <20220726010235.342927-1-leobras@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Migration with zero-copy-send currently has it's limitations, as it can't
be used with TLS nor any kind of compression. In such scenarios, it should
output errors during parameter / capability setting.
But currently there are some ways of setting this not-supported scenarios
without printing the error message:
!) For 'compression' capability, it works by enabling it together with
zero-copy-send. This happens because the validity test for zero-copy uses
the helper unction migrate_use_compression(), which check for compression
presence in s->enabled_capabilities[MIGRATION_CAPABILITY_COMPRESS].
The point here is: the validity test happens before the capability gets
enabled. If all of them get enabled together, this test will not return
error.
In order to fix that, replace migrate_use_compression() by directly testing
the cap_list parameter migrate_caps_check().
2) For features enabled by parameters such as TLS & 'multifd_compression',
there was also a possibility of setting non-supported scenarios: setting
zero-copy-send first, then setting the unsupported parameter.
In order to fix that, also add a check for parameters conflicting with
zero-copy-send on migrate_params_check().
3) XBZRLE is also a compression capability, so it makes sense to also add
it to the list of capabilities which are not supported with zero-copy-send.
Fixes: 1abaec9a1b ("migration: Change zero_copy_send from migration parameter to migration capability")
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Message-Id: <20220719122345.253713-1-leobras@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220711211112.18951-3-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It's useful for specifying tls credentials all in the cmdline (along with
the -object tls-creds-*), especially for debugging purpose.
The trick here is we must remember to not free these fields again in the
finalize() function of migration object, otherwise it'll cause double-free.
The thing is when destroying an object, we'll first destroy the properties
that bound to the object, then the object itself. To be explicit, when
destroy the object in object_finalize() we have such sequence of
operations:
object_property_del_all(obj);
object_deinit(obj, ti);
So after this change the two fields are properly released already even
before reaching the finalize() function but in object_property_del_all(),
hence we don't need to free them anymore in finalize() or it's double-free.
This also fixes a trivial memory leak for tls-authz as we forgot to free it
before this patch.
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185515.27475-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add migrate_channel_requires_tls() to detect whether the specific channel
requires TLS, leveraging the recently introduced migrate_use_tls(). No
functional change intended.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185513.27421-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add a property field that can conditionally disable the "break sending huge
page" behavior in postcopy preemption. By default it's enabled.
It should only be used for debugging purposes, and we should never remove
the "x-" prefix.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Manish Mishra <manish.mishra@nutanix.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185511.27366-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This patch allows the postcopy preempt channel to be created
asynchronously. The benefit is that when the connection is slow, we won't
take the BQL (and potentially block all things like QMP) for a long time
without releasing.
A function postcopy_preempt_wait_channel() is introduced, allowing the
migration thread to be able to wait on the channel creation. The channel
is always created by the main thread, in which we'll kick a new semaphore
to tell the migration thread that the channel has created.
We'll need to wait for the new channel in two places: (1) when there's a
new postcopy migration that is starting, or (2) when there's a postcopy
migration to resume.
For the start of migration, we don't need to wait for this channel until
when we want to start postcopy, aka, postcopy_start(). We'll fail the
migration if we found that the channel creation failed (which should
probably not happen at all in 99% of the cases, because the main channel is
using the same network topology).
For a postcopy recovery, we'll need to wait in postcopy_pause(). In that
case if the channel creation failed, we can't fail the migration or we'll
crash the VM, instead we keep in PAUSED state, waiting for yet another
recovery.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Manish Mishra <manish.mishra@nutanix.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185509.27311-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
To allow postcopy recovery, the ram fast load (preempt-only) dest QEMU thread
needs similar handling on fault tolerance. When ram_load_postcopy() fails,
instead of stopping the thread it halts with a semaphore, preparing to be
kicked again when recovery is detected.
A mutex is introduced to make sure there's no concurrent operation upon the
socket. To make it simple, the fast ram load thread will take the mutex during
its whole procedure, and only release it if it's paused. The fast-path socket
will be properly released by the main loading thread safely when there's
network failures during postcopy with that mutex held.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185506.27257-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This patch enables postcopy-preempt feature.
It contains two major changes to the migration logic:
(1) Postcopy requests are now sent via a different socket from precopy
background migration stream, so as to be isolated from very high page
request delays.
(2) For huge page enabled hosts: when there's postcopy requests, they can now
intercept a partial sending of huge host pages on src QEMU.
After this patch, we'll live migrate a VM with two channels for postcopy: (1)
PRECOPY channel, which is the default channel that transfers background pages;
and (2) POSTCOPY channel, which only transfers requested pages.
There's no strict rule of which channel to use, e.g., if a requested page is
already being transferred on precopy channel, then we will keep using the same
precopy channel to transfer the page even if it's explicitly requested. In 99%
of the cases we'll prioritize the channels so we send requested page via the
postcopy channel as long as possible.
On the source QEMU, when we found a postcopy request, we'll interrupt the
PRECOPY channel sending process and quickly switch to the POSTCOPY channel.
After we serviced all the high priority postcopy pages, we'll switch back to
PRECOPY channel so that we'll continue to send the interrupted huge page again.
There's no new thread introduced on src QEMU.
On the destination QEMU, one new thread is introduced to receive page data from
the postcopy specific socket (done in the preparation patch).
This patch has a side effect: after sending postcopy pages, previously we'll
assume the guest will access follow up pages so we'll keep sending from there.
Now it's changed. Instead of going on with a postcopy requested page, we'll go
back and continue sending the precopy huge page (which can be intercepted by a
postcopy request so the huge page can be sent partially before).
Whether that's a problem is debatable, because "assuming the guest will
continue to access the next page" may not really suite when huge pages are
used, especially if the huge page is large (e.g. 1GB pages). So that locality
hint is much meaningless if huge pages are used.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185504.27203-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Create a new socket for postcopy to be prepared to send postcopy requested
pages via this specific channel, so as to not get blocked by precopy pages.
A new thread is also created on dest qemu to receive data from this new channel
based on the ram_load_postcopy() routine.
The ram_load_postcopy(POSTCOPY) branch and the thread has not started to
function, and that'll be done in follow up patches.
Cleanup the new sockets on both src/dst QEMUs, meanwhile look after the new
thread too to make sure it'll be recycled properly.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185502.27149-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: With Peter's fix to quieten compiler warning on
start_migration
Firstly, postcopy already preempts precopy due to the fact that we do
unqueue_page() first before looking into dirty bits.
However that's not enough, e.g., when there're host huge page enabled, when
sending a precopy huge page, a postcopy request needs to wait until the whole
huge page that is sending to finish. That could introduce quite some delay,
the bigger the huge page is the larger delay it'll bring.
This patch adds a new capability to allow postcopy requests to preempt existing
precopy page during sending a huge page, so that postcopy requests can be
serviced even faster.
Meanwhile to send it even faster, bypass the precopy stream by providing a
standalone postcopy socket for sending requested pages.
Since the new behavior will not be compatible with the old behavior, this will
not be the default, it's enabled only when the new capability is set on both
src/dst QEMUs.
This patch only adds the capability itself, the logic will be added in follow
up patches.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185342.26794-2-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Now that all QEMUFile callbacks are removed, the entire concept can be
deleted.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The name 'ftell' gives the misleading impression that the QEMUFile
objects are seekable. This is not the case, as in general we just
have an opaque stream. The users of this method are only interested
in the total bytes processed. This switches to a new name that
reflects the intended usage.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Wrapped long line
When originally implemented, zero_copy_send was designed as a Migration
paramenter.
But taking into account how is that supposed to work, and how
the difference between a capability and a parameter, it only makes sense
that zero-copy-send would work better as a capability.
Taking into account how recently the change got merged, it was decided
that it's still time to make it right, and convert zero_copy_send into
a Migration capability.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: always define the capability, even on non-Linux but error if
set; avoids build problems with the capability
Implement zero copy send on nocomp_send_write(), by making use of QIOChannel
writev + flags & flush interface.
Change multifd_send_sync_main() so flush_zero_copy() can be called
after each iteration in order to make sure all dirty pages are sent before
a new iteration is started. It will also flush at the beginning and at the
end of migration.
Also make it return -1 if flush_zero_copy() fails, in order to cancel
the migration process, and avoid resuming the guest in the target host
without receiving all current RAM.
This will work fine on RAM migration because the RAM pages are not usually freed,
and there is no problem on changing the pages content between writev_zero_copy() and
the actual sending of the buffer, because this change will dirty the page and
cause it to be re-sent on a next iteration anyway.
A lot of locked memory may be needed in order to use multifd migration
with zero-copy enabled, so disabling the feature should be necessary for
low-privileged users trying to perform multifd migrations.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220513062836.965425-9-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
A lot of places check parameters.tls_creds in order to evaluate if TLS is
in use, and sometimes call migrate_get_current() just for that test.
Add new helper function migrate_use_tls() in order to simplify testing
for TLS usage.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220513062836.965425-6-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add property that allows zero-copy migration of memory pages
on the sending side, and also includes a helper function
migrate_use_zero_copy_send() to check if it's enabled.
No code is introduced to actually do the migration, but it allow
future implementations to enable/disable this feature.
On non-Linux builds this parameter is compiled-out.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220513062836.965425-5-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The 'status' field for the migration is updated normally using
an atomic operation from the migration thread.
Most readers of it aren't that careful, and in most cases it doesn't
matter.
In query_migrate->fill_source_migration_info the 'state'
is read twice; the first time to decide which state fields to fill in,
and then secondly to copy the state to the status field; that can end up
with a status that's inconsistent; e.g. setting up the fields
for 'setup' and then having an 'active' status. In that case
libvirt gets upset by the lack of ram info.
The symptom is:
libvirt.libvirtError: internal error: migration was active, but no RAM info was set
Read the state exactly once in fill_source_migration_info.
This is a possible fix for:
https://bugzilla.redhat.com/show_bug.cgi?id=2074205
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220413113329.103696-1-dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Previously migration didn't have an easy way to cleanup the listening
transport, migrate recovery only allows to execute once. That's done with a
trick flag in postcopy_recover_triggered.
Now the facility is already there.
Drop postcopy_recover_triggered and instead allows a new migrate-recover to
release the previous listener transport.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-8-peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We used to use postcopy_try_recover() to replace migration_incoming_setup() to
setup incoming channels. That's fine for the old world, but in the new world
there can be more than one channels that need setup. Better move the channel
setup out of it so that postcopy_try_recover() only handles the last phase of
switching to the recovery phase.
To do that in migration_fd_process_incoming(), move the postcopy_try_recover()
call to be after migration_incoming_setup(), which will setup the channels.
While in migration_ioc_process_incoming(), postpone the recover() routine right
before we'll jump into migration_incoming_process().
A side benefit is we don't need to pass in QEMUFile* to postcopy_try_recover()
anymore. Remove it.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-7-peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This variable, along with its helpers, is used to detect whether multiple
channel will be supported for migration. In follow up patches, there'll be
other capability that requires multi-channels. Hence move it outside multifd
specific code and make it public. Meanwhile rename it from "multifd" to
"multi_channels" to show its real meaning.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-5-peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We used to release it right after migrate_fd_connect(). That's not good
enough when there're more than one socket pair required, because it'll be
needed to establish TLS connection for the rest channels.
One example is multifd, where we copied over the hostname for each channel
but that's actually not needed.
Keeping the hostname until the cleanup phase of migration.
Cc: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-2-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Fixup checkpatch error; don't need to check for NULL
around g_free
Replace the global variables with inlined helper functions. getpagesize() is very
likely annotated with a "const" function attribute (at least with glibc), and thus
optimization should apply even better.
This avoids the need for a constructor initialization too.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220323155743.1585078-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Following the bdrv_activate renaming, change also the name
of the respective callers.
bdrv_invalidate_cache_all -> bdrv_activate_all
blk_invalidate_cache -> blk_activate
test_sync_op_invalidate_cache -> test_sync_op_activate
No functional change intended.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220209105452.1694545-5-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a helper to cleanup the transport listener.
When do it, we should also null-ify the cleanup hook and the data, then it's
even safe to call it multiple times.
Move the socket_address_list cleanup altogether, because that's a mirror of the
listener channels and only for the purpose of query-migrate. Hence when
someone wants to cleanup the listener transport, it should also want to cleanup
the socket list too, always.
No functional change intended.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220301083925.33483-15-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We used to have quite a few places making sure -EIO happened and that's the
only way to trigger postcopy recovery. That's based on the assumption that
we'll only return -EIO for channel issues.
It'll work in 99.99% cases but logically that won't cover some corner cases.
One example is e.g. ram_block_from_stream() could fail with an interrupted
network, then -EINVAL will be returned instead of -EIO.
I remembered Dave Gilbert pointed that out before, but somehow this is
overlooked. Neither did I encounter anything outside the -EIO error.
However we'd better touch that up before it triggers a rare VM data loss during
live migrating.
To cover as much those cases as possible, remove the -EIO restriction on
triggering the postcopy recovery, because even if it's not a channel failure,
we can't do anything better than halting QEMU anyway - the corpse of the
process may even be used by a good hand to dig out useful memory regions, or
the admin could simply kill the process later on.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220301083925.33483-11-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Provide information on the number of bytes copied in the pre-copy,
downtime and post-copy phases of migration.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It will just never fail. Drop those return values where they're constantly
zeros.
A tiny touch-up on the tracepoint so trace_ram_postcopy_send_discard_bitmap()
is called after the logic itself (which sounds more reasonable).
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The MIGRATION_STATUS_ACTIVE indicates that migration is running.
Remove it to be handled by the default operation,
It should be part of the unknown ending states.
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
COLO dose not support postcopy migration and remove the Fixme.
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In the migration_completion() no other status is expected, for
example MIGRATION_STATUS_CANCELLING, MIGRATION_STATUS_CANCELLED, etc.
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
virtio-net-failover test tries several device combinations that produces
some expected warnings.
These warning can be confusing, so we disable them during the qtest
sequence.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20211220145314.390697-1-lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
[thuth: Fix memory leak by using error_free()]
Signed-off-by: Thomas Huth <thuth@redhat.com>
When the PVM guest poweroff, the COLO thread may wait a semaphore
in colo_process_checkpoint().So, we should wake up the COLO thread
before migration shutdown.
Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch fixed as follows:
Thread 1 (Thread 0x7f34ee738d80 (LWP 11212)):
#0 __pthread_clockjoin_ex (threadid=139847152957184, thread_return=0x7f30b1febf30, clockid=<optimized out>, abstime=<optimized out>, block=<optimized out>) at pthread_join_common.c:145
#1 0x0000563401998e36 in qemu_thread_join (thread=0x563402d66610) at util/qemu-thread-posix.c:587
#2 0x00005634017a79fa in process_incoming_migration_co (opaque=0x0) at migration/migration.c:502
#3 0x00005634019b59c9 in coroutine_trampoline (i0=63395504, i1=22068) at util/coroutine-ucontext.c:115
#4 0x00007f34ef860660 in ?? () at ../sysdeps/unix/sysv/linux/x86_64/__start_context.S:91 from /lib/x86_64-linux-gnu/libc.so.6
#5 0x00007f30b21ee730 in ?? ()
#6 0x0000000000000000 in ?? ()
Thread 13 (Thread 0x7f30b3dff700 (LWP 11747)):
#0 __lll_lock_wait (futex=futex@entry=0x56340218ffa0 <qemu_global_mutex>, private=0) at lowlevellock.c:52
#1 0x00007f34efa000a3 in _GI__pthread_mutex_lock (mutex=0x56340218ffa0 <qemu_global_mutex>) at ../nptl/pthread_mutex_lock.c:80
#2 0x0000563401997f99 in qemu_mutex_lock_impl (mutex=0x56340218ffa0 <qemu_global_mutex>, file=0x563401b7a80e "migration/colo.c", line=806) at util/qemu-thread-posix.c:78
#3 0x0000563401407144 in qemu_mutex_lock_iothread_impl (file=0x563401b7a80e "migration/colo.c", line=806) at /home/workspace/colo-qemu/cpus.c:1899
#4 0x00005634017ba8e8 in colo_process_incoming_thread (opaque=0x563402d664c0) at migration/colo.c:806
#5 0x0000563401998b72 in qemu_thread_start (args=0x5634039f8370) at util/qemu-thread-posix.c:519
#6 0x00007f34ef9fd609 in start_thread (arg=<optimized out>) at pthread_create.c:477
#7 0x00007f34ef924293 in clone () at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95
The QEMU main thread is holding the lock:
(gdb) p qemu_global_mutex
$1 = {lock = {_data = {lock = 2, __count = 0, __owner = 11212, __nusers = 9, __kind = 0, __spins = 0, __elision = 0, __list = {_prev = 0x0, __next = 0x0}},
__size = "\002\000\000\000\000\000\000\000\314+\000\000\t", '\000' <repeats 26 times>, __align = 2}, file = 0x563401c07e4b "util/main-loop.c", line = 240,
initialized = true}
>From the call trace, we can see it is a deadlock bug. and the QEMU main thread holds the global mutex to wait until the COLO thread ends. and the colo thread
wants to acquire the global mutex, which will cause a deadlock. So, we should release the qemu_global_mutex before waiting colo thread ends.
Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch fixes the following:
qemu-system-x86_64: invalid runstate transition: 'shutdown' -> 'running'
Aborted (core dumped)
The gdb bt as following:
0 __GI_raise (sig=sig@entry=6) at ../sysdeps/unix/sysv/linux/raise.c:50
1 0x00007faa3d613859 in __GI_abort () at abort.c:79
2 0x000055c5a21268fd in runstate_set (new_state=RUN_STATE_RUNNING) at vl.c:723
3 0x000055c5a1f8cae4 in vm_prepare_start () at /home/workspace/colo-qemu/cpus.c:2206
4 0x000055c5a1f8cb1b in vm_start () at /home/workspace/colo-qemu/cpus.c:2213
5 0x000055c5a2332bba in migration_iteration_finish (s=0x55c5a4658810) at migration/migration.c:3376
6 0x000055c5a2332f3b in migration_thread (opaque=0x55c5a4658810) at migration/migration.c:3527
7 0x000055c5a251d68a in qemu_thread_start (args=0x55c5a5491a70) at util/qemu-thread-posix.c:519
8 0x00007faa3d7e9609 in start_thread (arg=<optimized out>) at pthread_create.c:477
9 0x00007faa3d710293 in clone () at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95
Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
If the compression migration fails or is canceled, the query for the value of
compression_counters during the next compression migration is wrong.
Signed-off-by: yuxiating <yuxiating@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This avoids to call migrate_get_current() in the caller function
whereas migration_cancel() already needs the pointer to the current
migration state.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Let's use QEMU_ALIGN_DOWN() and friends to make the code a bit easier to
read.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
An internal version that removes -only-migratable implications. It can be used
for temporary migration blockers like dump-guest-memory.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
save_snapshot() checks migration blocker, which looks sane. At the meantime we
should also teach the blocker add helper to fail if during a snapshot, just
like for migrations.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To: <quintela@redhat.com>, <dgilbert@redhat.com>, <qemu-devel@nongnu.org>
CC: Li Zhijian <lizhijian@cn.fujitsu.com>
Date: Sat, 31 Jul 2021 22:05:52 +0800 (5 weeks, 4 days, 17 hours ago)
And change the default to true so that in '-incoming defer' case, user is able
to change multifd capability.
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To: <quintela@redhat.com>, <dgilbert@redhat.com>, <qemu-devel@nongnu.org>
CC: Li Zhijian <lizhijian@cn.fujitsu.com>
Date: Sat, 31 Jul 2021 22:05:51 +0800 (5 weeks, 4 days, 17 hours ago)
multifd with unsupported protocol will cause a segment fault.
(gdb) bt
#0 0x0000563b4a93faf8 in socket_connect (addr=0x0, errp=0x7f7f02675410) at ../util/qemu-sockets.c:1190
#1 0x0000563b4a797a03 in qio_channel_socket_connect_sync
(ioc=0x563b4d16e8c0, addr=0x0, errp=0x7f7f02675410) at
../io/channel-socket.c:145
#2 0x0000563b4a797abf in qio_channel_socket_connect_worker (task=0x563b4cd86c30, opaque=0x0) at ../io/channel-socket.c:168
#3 0x0000563b4a792631 in qio_task_thread_worker (opaque=0x563b4cd86c30) at ../io/task.c:124
#4 0x0000563b4a91da69 in qemu_thread_start (args=0x563b4c44bb80) at ../util/qemu-thread-posix.c:541
#5 0x00007f7fe9b5b3f9 in ?? ()
#6 0x0000000000000000 in ?? ()
It's enough to check migrate_multifd_is_allowed() in multifd cleanup() and
multifd setup() though there are so many other places using migrate_use_multifd().
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
qemu_savevm_state_complete_postcopy assumes the iothread lock (BQL)
to be held, but instead it isn't.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20211005080751.3797161-3-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit b673eab4e2 "multifd: Make multifd_load_setup() get an Error
parameter" changed migration_incoming_setup() to take an Error **
argument, and adjusted the callers accordingly. It neglected to
change adjust multifd_load_setup(): it still exit()s on error. Clean
that up.
The error now gets propagated up two call chains: via
migration_fd_process_incoming() to rdma_accept_incoming_migration(),
and via migration_ioc_process_incoming() to
migration_channel_process_incoming(). Both chain ends report the
error with error_report_err(), but otherwise ignore it. Behavioral
change: we no longer exit() on this error.
This is consistent with how we handle other errors here, e.g. from
multifd_recv_new_channel() via migration_ioc_process_incoming() to
migration_channel_process_incoming(). Whether it's consistently right
or consistently wrong I can't tell.
Also clean up the return value from the unusual 0 on success, 1 on
error to the more common true on success, false on error.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-11-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
We did this with scripts/coccinelle/use-error_fatal.cocci before, in
commit 50beeb6809 and 007b06578a. This commit cleans up rarer
variations that don't seem worth matching with Coccinelle.
Cc: Thomas Huth <thuth@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-2-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
It's efficient, but hackish to call yank unregister calls in channel_close(),
especially it'll be hard to debug when qemu crashed with some yank function
leaked.
Remove that hack, but instead explicitly unregister yank functions at the
places where needed, they are:
(on src)
- migrate_fd_cleanup
- postcopy_pause
(on dst)
- migration_incoming_state_destroy
- postcopy_pause_incoming
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210722175841.938739-6-peterx@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Accessing from_dst_file is potentially racy in current code base like below:
if (s->from_dst_file)
do_something(s->from_dst_file);
Because from_dst_file can be reset right after the check in another
thread (rp_thread). One example is migrate_fd_cancel().
Use the same qemu_file_lock to protect it too, just like to_dst_file.
When it's safe to access without lock, comment it.
There's one special reference in migration_thread() that can be replaced by
the newly introduced rp_thread_created flag.
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Message-Id: <20210722175841.938739-3-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
with Peter's fixup
It's possible that the migration thread skip the join() of the rp_thread in
below race and crash on src right at finishing migration:
migration_thread rp_thread
---------------- ---------
migration_completion()
(before rp_thread quits)
from_dst_file=NULL
[thread got scheduled out]
s->rp_state.from_dst_file==NULL
(skip join() of rp_thread)
migrate_fd_cleanup()
qemu_fclose(s->to_dst_file)
yank_unregister_instance()
assert(yank_find_entry()) <------- crash
It could mostly happen with postcopy, but that shouldn't be required, e.g., I
think it could also trigger with MIGRATION_CAPABILITY_RETURN_PATH set.
It's suspected that above race could be the root cause of a recent (but rare)
migration-test break reported by either Dave or PMM:
https://lore.kernel.org/qemu-devel/YPamXAHwan%2FPPXLf@work-vm/
The issue is: from_dst_file is reset in the rp_thread, so if the thread reset
it to NULL fast enough then the migration thread will assume there's no
rp_thread at all.
This could potentially cause more severe issue (e.g. crash) after the yank code.
Fix it by using a boolean to keep "whether we've created rp_thread".
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210722175841.938739-2-peterx@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
For each "migrate" command, remember to clear the s->error before going on.
For one reason, when there's a new error it'll be still remembered; see
migrate_set_error() who only sets the error if error==NULL. Meanwhile if a
failed migration completes (e.g., postcopy recovered and finished), we
shouldn't dump an error when calling migrate_fd_cleanup() at last.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210708190653.252961-4-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Below process could crash qemu with postcopy recovery:
1. (hmp) migrate -d ..
2. (hmp) migrate_start_postcopy
3. [network down, postcopy paused]
4. (hmp) migrate -r $WRONG_PORT
when try the recover on an invalid $WRONG_PORT, cleanup_bh will be cleared
5. (hmp) migrate -r $RIGHT_PORT
[qemu crash on assert(cleanup_bh)]
The thing is we shouldn't cleanup if it's postcopy resume; the error is set
mostly because the channel is wrong, so we return directly waiting for the user
to retry.
migrate_fd_cleanup() should only be called when migration is cancelled or
completed.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210708190653.252961-3-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When postcopy pause triggered, we rely on the migration thread to cleanup the
to_dst_file handle, and the return path thread to cleanup the from_dst_file
handle (which is stored in the local variable "rp").
Within the process, from_dst_file cleanup (qemu_fclose) is postponed until it's
setup again due to a postcopy recovery.
It used to work before yank was born; after yank is introduced we rely on the
refcount of IOC to correctly unregister yank function in channel_close(). If
without the early and on-time release of from_dst_file handle the yank function
will be leftover during paused postcopy.
Without this patch, below steps (quoted from Xiaohui) could trigger qemu src
crash:
1.Boot vm on src host
2.Boot vm on dst host
3.Enable postcopy on src&dst host
4.Load stressapptest in vm and set postcopy speed to 50M
5.Start migration from src to dst host, change into postcopy mode when migration is active.
6.When postcopy is active, down the network card(do migration via this network) on dst host.
7.Wait untill postcopy is paused on src&dst host.
8.Before up network card, recover migration on dst host, will get error like following.
9.Ignore the error of step 8, go on recovering migration on src host:
After step 9, qemu on src host will core dump after some seconds:
qemu-kvm: ../util/yank.c:107: yank_unregister_instance: Assertion `QLIST_EMPTY(&entry->yankfns)' failed.
1.sh: line 38: 44662 Aborted (core dumped)
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210708190653.252961-2-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When the migration fails or is canceled we wait the end of the unplug
operation to be able to plug it back. But if the unplug operation
is never finished we stop to wait and QEMU emits a warning to inform
the user.
Based-on: 20210629155007.629086-1-lvivier@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210701131458.112036-1-lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If the user cancels the migration in the unplug-wait state,
QEMU will try to plug back the card and this fails because the card
is partially unplugged.
To avoid the problem, continue to wait the card unplug, but to
allow the migration to be canceled if the card never finishes to unplug
use a timeout.
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1976852
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210629155007.629086-3-lvivier@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The loop is used in migration_thread() and bg_migration_thread(),
so we can move it to its own function and call it from these both places.
Moreover, in migration_thread() we have a wrong state transition from
SETUP to ACTIVE while state could be WAIT_UNPLUG. This is correctly
managed in bg_migration_thread() so use this code instead.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210629155007.629086-2-lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It's possible qemu_start_incoming_migration() failed at any point, when it
happens we should reset postcopy_recover_triggered to false so that the user
can still retry with a saner incoming port.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210629181356.217312-3-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Starting from commit b5eea99ec2, qmp_migrate_recover() calls unregister
before calling qemu_start_incoming_migration(). I believe it wanted to mitigate
the next call to yank_register_instance(), but I think that's wrong.
Firstly, if during recover, we should keep the yank instance there, not
"quickly removing and adding it back".
Meanwhile, calling qmp_migrate_recover() twice with b5eea99ec2 will directly
crash the dest qemu (right now it can't; but it'll start to work right after
the next patch) because the 1st call of qmp_migrate_recover() will unregister
permanently when the channel failed to establish, then the 2nd call of
qmp_migrate_recover() crashes at yank_unregister_instance().
This patch fixes it by moving yank ops out of qemu_start_incoming_migration()
into qmp_migrate_incoming. For qmp_migrate_recover(), drop the unregister of
yank instance too since we keep it there during the recovery phase.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210629181356.217312-2-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This is a critical failure scenario for migration that is hard to
diagnose from existing probes. Most likely it is caused by an error
from bdrv_flush(), but we're not logging the errno anywhere, hence
this new probe.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
We can detect disk migration in migrate_prepare, if disk migration
is enabled in COLO mode, we can directly report an error.and there
is no need to disable block migration at every checkpoint.
Signed-off-by: Lei Rao <lei.rao@intel.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a cleanup hook for incoming migration that gets called
at the end as a way for a transport to allow cleanup.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210421112834.107651-4-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The CONFIG_VFIO switch only works in target specific code. Since
migration/migration.c is common code, the #ifdef does not have
the intended behavior here. Move the related code to a separate
file now which gets compiled via specific_ss instead.
Fixes: 3710586caa ("qapi: Add VFIO devices migration stats in Migration stats")
Message-Id: <20210414112004.943383-3-thuth@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Resizing while migrating is dangerous and does not work as expected.
The whole migration code works on the usable_length of ram blocks and does
not expect this to change at random points in time.
In the case of precopy, the ram block size must not change on the source,
after syncing the RAM block list in ram_save_setup(), so as long as the
guest is still running on the source.
Resizing can be trigger *after* (but not during) a reset in
ACPI code by the guest
- hw/arm/virt-acpi-build.c:acpi_ram_update()
- hw/i386/acpi-build.c:acpi_ram_update()
Use the ram block notifier to get notified about resizes. Let's simply
cancel migration and indicate the reason. We'll continue running on the
source. No harm done.
Update the documentation. Postcopy will be handled separately.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210429112708.12291-5-david@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Manual merge
Result @blocked is redundant. Unfortunately, we realized this too
close to the release to risk dropping it, so we deprecated it
instead, in commit e11ce6c06.
Since it was deprecated from the start, we can delete it without
the customary grace period. Do so.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210429140424.2802929-1-armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This commit solves the issue with userfault_fd WP feature that
background snapshot is based on. For any never poluated or discarded
memory page, the UFFDIO_WRITEPROTECT ioctl() would skip updating
PTE for that page, thereby loosing WP setting for it.
So we need to pre-fault pages for each RAM block to be protected
before making a userfault_fd wr-protect ioctl().
Fixes: 278e2f551a (migration: support
UFFD write fault processing in ram_save_iterate())
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Reported-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210401092226.102804-4-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert:
Bodged ifdef __linux__ on ram_write_tracking_prepare, should really
go in a stub
The same thing as for incoming postcopy - we cannot deal with concurrent
RAM discards when using background snapshot feature in outgoing migration.
Fixes: 8518278a6a (migration: implementation
of background snapshot thread)
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Reported-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210401092226.102804-3-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Added missing qemu_fflush() on buffer file holding precopy device state.
Increased initial QIOChannelBuffer allocation to 512KB to avoid reallocs.
Typical configurations often require >200KB for device state and VMDESC.
Fixes: 8518278a6a (migration: implementation
of background snapshot thread)
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Message-Id: <20210401092226.102804-2-andrey.gruzdev@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The generic 'migrate_set_parameters' command handle all types of param.
Only the QMP commands were documented in the deprecations page, but the
rationale for deprecating applies equally to HMP, and the replacements
exist. Furthermore the HMP commands are just shims to the QMP commands,
so removing the latter breaks the former unless they get re-implemented.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Replaced various qemu_mutex_lock calls and their respective
qemu_mutex_unlock calls with QEMU_LOCK_GUARD macro. This simplifies
the code by eliminating the respective qemu_mutex_unlock calls.
Signed-off-by: Mahmoud Mandour <ma.mandourr@gmail.com>
Message-Id: <20210311031538.5325-7-ma.mandourr@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Modify query-migrate so that it has a flag indicating if outbound
migration is blocked, and if it is a list of reasons.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210202135522.127380-2-dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
migrate_params_check() has a number of error messages of the form
Parameter 'NAME' expects is invalid, it should be ...
Fix them to something like
Parameter 'NAME' expects a ...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210202141734.2488076-5-armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Lukas Straub