Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base address of the SMBus io ports and its enabled status is set
by registers in the PCI config space but this was not correctly
emulated. Instead the SMBus registers were mapped on realize to the
base address set by a property to the address expected by fuloong2e
firmware.
Fix the base and config register handling to more closely model
hardware which allows to remove the property and allows the guest to
control this mapping. Do all this in reset instead of realize so it's
correctly updated on reset.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <f2ca2ad5f08ba8cee07afd9d67b4e75cda21db09.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move lines around so that object definitions become consecutive and
not scattered around. This brings functions belonging to an object
together so it's clearer what is defined and what parts belong to
which object.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <9f942989dba46fc1c23b881f6cb135948f818c2f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The superio memory region holds the io space index/data registers used
to access the superio config registers that are implemented in struct
SuperIOConfig. To keep these related things together move the memory
region to SuperIOConfig and rename it accordingly.
Also remove the unused "data" member of SuperIOConfig which is not
needed as we store actual data values in the regs array.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <dc3c4e7632716ca73c10506bd02ee93b39c28705.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use less confusing naming for superio config register handling related
parts that makes it clearer what belongs to this part.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <4d30a2b4b771b2ad651509885daae79d7c4fe7a8.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Rename local variable holding object state for readability and
consistency.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <69655b23df2ecebbf0aff29726f4b4746f5b74de.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These are not used or not needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <35cefcc3518a3395a796bb6ad6fbc308adc65266.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Drop DPRINTF and use trace functions instead. Two debug messages about
unimplemented registers could be converted to qemu_log_mask() but in
reality all registers are currently unimplemented (we just store and
return values of writable regs but do nothing with them). As we
already trace register access there's no need for additional debug
messages so these are just removed and a comment is added as a reminder.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <785854022a37035f66d89e70cb6ca1bc0e0d0163.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove legacy vt82c686b_pm_init() function and also rename
VT82C686B_PM type name to match other device names.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a70982b32f11222d335385b90749abb6cf2e2cce.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The via-[am]c97 code is supposed to implement the audio part of VIA
south bridge chips so it is better placed under hw/audio/. Split it
off into a separate file.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <af083634e3b9efe67e6c4247cf0185d3fa7b1810.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These are legacy init functions that are just equivalent to directly
calling pci_create_simple so do that instead. Also rename objects to
lower case via-ac97 and via-mc97 matching naming of other devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1c4373c8aeb6c4fb2a8df2c864b0e91a977a3d7b.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is really the ISA bridge part so name the type accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <78db2ced4b41a8a775dbc6c97a90db683952c2cb.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There's no reason to suffix everything with _DEVICE when the names are
already unique without it and shorter names are more readable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <ea89683ebb3528c0f79ed99d3d3cfcefb63c3bfb.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These parts are common between VT82C686B and VT8231 so can be shared
in the future. Rename them to VIA prefix accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <510ddb17836a2c2e68a27cf2dcaee420bc2efbc1.1609584215.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We already have a generic PCI_SLOT() macro in "hw/pci/pci.h"
to extract the PCI slot identifier, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201012124506.3406909-5-philmd@redhat.com>
Keep CPU hotunplug with SMI disabled on 5.2 and older and enable
it by default on newer machine types.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be reused by next patch to check validity of unplug
feature.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023121933.19227-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
libFuzzer triggered the following assertion:
cat << EOF | qemu-system-i386 -M pc-q35-5.0 \
-nographic -monitor none -serial none \
-qtest stdio -d guest_errors -trace pci\*
outl 0xcf8 0x8400f841
outl 0xcfc 0xebed205d
outl 0x5d02 0xedf82049
EOF
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
hw/pci/pci.c:268: int pci_bus_get_irq_level(PCIBus *, int): Assertion `irq_num < bus->nirq' failed.
This is because ich9_lpc_sci_irq() returns -1 for reserved
(illegal) values, but ich9_lpc_pmbase_sci_update() considers
it valid and store it in a 8-bit unsigned type. Then the 255
value is used as GSI IRQ, resulting in a PIRQ value of 247,
more than ICH9_LPC_NB_PIRQS (8).
Fix by simply ignoring the invalid access (and reporting it):
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
ICH9 LPC: SCI IRQ SEL #3 is reserved
pci_cfg_read mch 00:0 @0x0 -> 0x8086
pci_cfg_read mch 00:0 @0x0 -> 0x29c08086
...
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: 8f242cb724 ("ich9: implement SCI_IRQ_SEL register")
BugLink: https://bugs.launchpad.net/qemu/+bug/1878642
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200717151705.18611-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the "smi_negotiated_features" field of ICH9LPCState as
a QOM property.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will allow firmware to notify QEMU that firmware requires SMI
being triggered on CPU hot[un]plug, so that it would be able to account
for hotplugged CPU and relocate it to new SMM base and/or safely remove
CPU on unplug.
Using negotiated features, follow up patches will insert SMI upcall
into AML code, to make sure that firmware processes hotplug before
guest OS would attempt to use new CPU.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This makes the code consistent with the rest of QOM code in QEMU,
and will make automated conversion to type declaration macros
simpler.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200824215936.2961951-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As we can never have more than ISA_NUM_IRQS (16) ISA IRQs,
replace the not very interesting hw_error() call by an
assert() which is more useful to debug condition that can
not happen.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200901104043.91383-6-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When realizing a Super I/O with IDE controller [*], we get:
qom/object.c:1684: object_property_try_add_child: Assertion `!child->parent' failed.
Aborted (core dumped)
This is because the device is already realized when we try to
add the QOM property to the parent. Fix by realizing *after*
adding the QOM relationship.
[*] Set ISASuperIOClass::ide.count = N with N not zero
(no such thing currently exists; the bug is latent)
Fixes: e508430619 ("hw/isa/superio: Make the components QOM children")
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200721124516.9602-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-37-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
Instead of creating and returning the pc speaker accept it as argument.
That allows to rework the initialization workflow in followup patches.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200702132525.6849-16-kraxel@redhat.com
The floppy controller devices desugar their drive properties into
floppy devices (since commit a92bd191a4 "fdc: Move qdev properties to
FloppyDrive", v2.8.0). This involves some bad magic in
fdctrl_connect_drives(), and exists for backward compatibility.
The functions for boards to create floppy controller devices
fdctrl_init_isa(), fdctrl_init_sysbus(), and sun4m_fdctrl_init()
desugar -drive if=floppy to these floppy controller drive properties.
If you use both -drive if=floppy (or its -fda / -fdb sugar) and
-global isa-fdc for the same floppy device, -global silently loses the
conflict, and both backends involved end up with the floppy device
frontend attached, as demonstrated by iotest 172 (see commit before
previous). This is wrong.
Desugar -drive if=floppy straight to floppy devices instead, with
helper fdctrl_init_drives(). The conflict now gets rejected cleanly:
first, fdctrl_connect_drives() creates the floppy for the controller's
property, then fdctrl_init_drives() attempts to create the floppy for
-drive if=floppy, but fails because the unit is already in use.
Output of iotest 172 changes in three ways:
1. The clash gets rejected.
2. In one test case, "info qtree" has the floppy devices swapped, and
"info block" has their QOM paths swapped. This is because the
floppy device for -fda now gets created after the one for -global
isa-fdc.driveB.
3. The error message for -global floppy.drive=floppy0 changes. Before
the patch, we set isa-fdc.driveA to -fda's block backend, then
create the floppy device for it, then move the backend from
isa-fdc.driveA to floppy.drive. Floppy creation fails when
applying -global floppy.drive=floppy0, because floppy0 is still
attached to isa-fdc. After the patch, we create the floppy for
-fda, then set its drive property to floppy0. Now floppy creation
succeeds, but setting the drive property fails, because -global
already set it. Yes, this is exasperatingly complicated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-5-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-22-armbru@redhat.com>
I'm converting from qdev_create()/qdev_init_nofail() to
qdev_new()/qdev_realize_and_unref(); recent commit "qdev: New
qdev_new(), qdev_realize(), etc." explains why.
ISA devices use qdev_create() through isa_create() and
isa_try_create().
Provide isa_new(), isa_try_new(), and isa_realize_and_unref() for
converting ISA devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-19-armbru@redhat.com>
In addition to the qdev_create() patterns converted so far, we have a
qdev_set_parent_bus() pattern. Mostly when we embed a device in a
parent device rather than allocating it on the heap.
This pattern also puts devices in the dangerous "no QOM parent, but
plugged into bus" state I explained in recent commit "qdev: New
qdev_new(), qdev_realize(), etc."
Apply same solution: convert to qdev_realize(). Coccinelle script:
@@
expression dev, bus, errp;
symbol true;
@@
- qdev_set_parent_bus(DEVICE(dev), bus);
...
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), bus, errp);
@ depends on !(file in "qdev-monitor.c") && !(file in "hw/core/qdev.c")@
expression dev, bus, errp;
symbol true;
@@
- qdev_set_parent_bus(dev, bus);
...
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(dev, bus, errp);
@@
expression dev, bus;
symbol true;
@@
- qdev_set_parent_bus(DEVICE(dev), bus);
...
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize(DEVICE(dev), bus, &error_fatal);
Unconverted uses of qdev_set_parent_bus() remain. They'll be
converted later in this series.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-12-armbru@redhat.com>
[Also convert new hw/virtio/vhost-user-vsock-pci.c]
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
This code is not related to hardware emulation.
Move it under accel/ with the other hypervisors.
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200508100222.7112-1-philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
BALATON Zoltan