QEMU initializes preallocated backend memory as the objects are parsed from
the command line. This is not optimal in some cases (e.g. memory spanning
multiple NUMA nodes) because the memory objects are initialized in series.
Allow the initialization to occur in parallel (asynchronously). In order to
ensure optimal thread placement, asynchronous initialization requires prealloc
context threads to be in use.
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Message-ID: <20240131165327.3154970-2-mark.kanda@oracle.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We used to check that the memory region size is multiples of the overall
requested address alignment for the device memory address.
We removed that check, because there are cases (i.e., hv-balloon) where
devices unconditionally request an address alignment that has a very large
alignment (i.e., 32 GiB), but the actual memory device size might not be
multiples of that alignment.
However, this change:
(a) allows for some practically impossible DIMM sizes, like "1GB+1 byte".
(b) allows for DIMMs that partially cover hugetlb pages, previously
reported in [1].
Both scenarios don't make any sense: we might even waste memory.
So let's reintroduce that check, but only check that the
memory region size is multiples of the memory region alignment (i.e.,
page size, huge page size), but not any additional memory device
requirements communicated using md->get_min_alignment().
The following examples now fail again as expected:
(a) 1M with 2M THP
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-ram,id=mem1,size=1M \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x200000
(b) 1G+1byte
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-ram,id=mem1,size=1073741825B \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x200000
(c) Unliagned hugetlb size (2M)
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-file,id=mem1,mem-path=/dev/hugepages/tmp,size=511M \
-device pc-dimm,id=dimm1,memdev=mem1
backend memory size must be multiple of 0x200000
(d) Unliagned hugetlb size (1G)
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-file,id=mem1,mem-path=/dev/hugepages1G/tmp,size=2047M \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x40000000
Note that this fix depends on a hv-balloon change to communicate its
additional alignment requirements using get_min_alignment() instead of
through the memory region.
[1] https://lkml.kernel.org/r/f77d641d500324525ac036fe1827b3070de75fc1.1701088320.git.mprivozn@redhat.com
Message-ID: <20240117135554.787344-3-david@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Reported-by: Michal Privoznik <mprivozn@redhat.com>
Fixes: eb1b7c4bd4 ("memory-device: Drop size alignment check")
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
The character "+" is now forbidden in QOM device names (see commit
b447378e12 - "Limit type names to alphanumerical and some few special
characters"). For the "power5+" and "power7+" CPU names, there is
currently a hack in type_name_is_valid() to still allow them for
compatibility reasons. However, there is a much nicer solution for this:
Simply use aliases! This way we can still support the old names without
the need for the ugly hack in type_name_is_valid().
Message-ID: <20240117141054.73841-2-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When the maximum count of SCRIPTS instructions is reached, the code
stops execution and returns, but fails to decrement the reentrancy
counter. This effectively renders the SCSI controller unusable
because on next entry the reentrancy counter is still above the limit.
This bug was seen on HP-UX 10.20 which seems to trigger SCRIPTS
loops.
Fixes: b987718bbb ("hw/scsi/lsi53c895a: Fix reentrancy issues in the LSI controller (CVE-2023-0330)")
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-ID: <20240128202214.2644768-1-svens@stackframe.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Let's implement the get_min_alignment() callback for memory devices, and
copy for the device memory region the alignment of the host memory
region. This mimics what virtio-mem does, and allows for re-introducing
proper alignment checks for the memory region size (where we don't care
about additional device requirements) in memory device core.
Message-ID: <20240117135554.787344-2-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
This function is no longer used, as all its callers have been converted
to use pci_init_nic_devices() instead.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Obtain the MAC address from the NIC configuration if there is one, or
generate one explicitly so that it can be placed in the PROM.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Create the device only if there is a corresponding NIC config for it.
Remove the explicit check on nd_table[0].used from hw/hppa/machine.c
which (since commit d8a3220005) tries to do the same thing.
The lasi_82596 support has been disabled since it was first introduced,
since enable_lasi_lan() has always been zero. This allows the user to
enable it by explicitly requesting a NIC model 'lasi_82596' or just
using the alias 'lasi'. Otherwise, it defaults to a PCI NIC as before.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
When converting to the shiny build-system-du-jour, a typo prevented the
last_i82596 driver from being built. Correct the config option name to
re-enable the build. And include "sysemu/sysemu.h" so it actually builds.
Fixes: b1419fa665 ("meson: convert hw/net")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2144
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The MIPS SIM platform instantiates its NIC only if a corresponding
configuration exists for it. Use qemu_create_nic_device() function for
that.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
If a corresponding NIC configuration was found, it will have a MAC address
already assigned, so use that. Else, generate and assign a default one.
Using qemu_find_nic_info() is simpler than the alternative of using
qemu_configure_nic_device() and then having to fetch the "mac" property
as a string and convert it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Rather than just using qemu_configure_nic_device(), populate the MAC
address in the system-registers device by peeking at the NICInfo before
it's assigned to the device.
Generate the MAC address early, if there is no matching -nic option.
Otherwise the MAC address wouldn't be generated until net_client_init1()
runs.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Also update the test to specify which device to attach the test socket
to, and remove the comment lamenting the fact that we can't do so.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preseve the existing behaviour for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preserve the existing behaviour of each caller for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The first sunhme NIC gets placed a function 1 on slot 1 of PCI bus A,
and the rest are dynamically assigned on PCI bus B.
Previously, any PCI NIC would get the special treatment purely by
virtue of being first in the list.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Previously, the first PCI NIC would be assigned to slot 2 even if the
user override the model and made it something other than an rtl8139
which is the default. Everything else would be dynamically assigned.
Now, the first rtl8139 gets slot 2 and everything else is dynamic.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Avoid directly referencing nd_table[] by first instantiating any
spapr-vlan devices using a qemu_get_nic_info() loop, then calling
pci_init_nic_devices() to do the rest.
No functional change intended.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Previously, the first PCI NIC would be placed in PCI slot 3 and the rest
would be dynamically assigned. Even if the user overrode the default NIC
type and made it something other than PCNet.
Now, the first PCNet NIC (that is, anything not explicitly specified
to be anything different) will go to slot 3 even if it isn't the first
NIC specified on the command line. And anything else will be dynamically
assigned.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The Malta board setup code would previously place the first NIC into PCI
slot 11 if was a PCNet card, and the rest (including the first if it was
anything other than a PCNet card) would be dynamically assigned.
Now it will place any PCNet NIC into slot 11, and then anything else will
be dynamically assigned.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The previous behaviour was: *if* the first NIC specified on the command
line was an RTL8139 (or unspecified model) then it gets assigned to PCI
slot 7, which is where the Fuloong board had an RTL8139. All other
devices (including the first, if it was specified as anything other than
an rtl8319) get dynamically assigned on the bus.
The new behaviour is subtly different: If the first NIC was given a
specific model *other* than rtl8139, and a subsequent NIC was not,
then the rtl8139 (or unspecified) NIC will go to slot 7 and the rest
will be dynamically assigned.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
When instantiating XenBus itself, for each NIC which is configured with
either the model unspecified, or set to to "xen" or "xen-net-device",
create a corresponding xen-net-device for it.
Now we can revert the previous more hackish version which relied on the
platform code explicitly registering the NICs on its own XenBus, having
returned the BusState* from xen_bus_init() itself.
This also fixes the setup for Xen PV guests, which was previously broken
in various ways and never actually managed to peer with the netdev.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Eliminate direct access to nd_table[] and nb_nics by processing the the
Xen and ISA NICs first and then calling pci_init_nic_devices() for the
rest.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The loop over nd_table[] to add PCI NICs is repeated in quite a few
places. Add a helper function to do it.
Some platforms also try to instantiate a specific model in a specific
slot, to match the real hardware. Add pci_init_nic_in_slot() for that
purpose.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
This patch will allow the SPI controller to be accessible from BCM2835 based
boards as SPI0. SPI driver is usually disabled by default and config.txt does
not work.
Instead, dtmerge can be used to apply spi=on on a bcm2835 dtb file.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-3-rayhan.faizel@gmail.com
[PMM: indent tweak]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the SPI controller for the BCM2835. Polling and interrupt modes
of transfer are supported. DMA and LoSSI modes are currently unimplemented.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-2-rayhan.faizel@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Implementation of Transmit function for packets
- Implementation for reading and writing from and to descriptors in
memory for Tx
Added relevant trace-events
NOTE: This function implements the steps detailed in the datasheet for
transmitting messages from the GMAC.
Change-Id: Icf14f9fcc6cc7808a41acd872bca67c9832087e6
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-6-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Implementation of Receive function for packets
- Implementation for reading and writing from and to descriptors in
memory for Rx
When RX starts, we need to flush the queued packets so that they
can be received by the GMAC device. Without this it won't work
with TAP NIC device.
When RX descriptor list is full, it returns a DMA_STATUS for
software to handle it. But there's no way to indicate the software has
handled all RX descriptors and the whole pipeline stalls.
We do something similar to NPCM7XX EMC to handle this case.
1. Return packet size when RX descriptor is full, effectively dropping
these packets in such a case.
2. When software clears RX descriptor full bit, continue receiving
further packets by flushing QEMU packet queue.
Added relevant trace-events
Change-Id: I132aa254a94cda1a586aba2ea33bbfc74ecdb831
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-5-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the basic registers of GMAC device and sets
registers for networking functionalities.
Squashed IRQ Implementation patch into this one for compliation.
Tested:
The following message shows up with the change:
Broadcom BCM54612E stmmac-0:00: attached PHY driver [Broadcom BCM54612E] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
stmmaceth f0802000.eth eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Change-Id: If71c6d486b95edcccba109ba454870714d7e0940
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Nabih Estefan Diaz <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-2-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to the QEMU Coding Style document:
> Do not use printf(), fprintf() or monitor_printf(). Instead, use
> error_report() or error_vreport() from error-report.h. This ensures the
> error is reported in the right place (current monitor or stderr), and in
> a uniform format.
> Use error_printf() & friends to print additional information.
This commit changes fprintfs that report warnings and errors to the
appropriate report functions.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 42a8953553cf68e8bacada966f93af4fbce45919.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on tracepoints should be able to opt-in to each tracepoint and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into tracepoints.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: b000ab73022dfeb7a7ab0ee8fd0f41fb208adaf0.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on tracepoints should be able to opt-in to each tracepoint and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into tracepoints.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 2fbe1fbc59078e384761c932e97cfa4276a53d75.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. Errors or warnings are converted to error_report and
warn_report calls.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: fe5e3bd54231abe933f95a24e0e88208cd8cfd8f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 799c5141c5751cf2341e1d095349612e046424a8.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.
This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.#
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 39db71dd87bf2007cf7812f3d91dde53887f1f2f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The latest version of qemu (v8.2.0-869-g7a1dc45af5) crashes when booting
the mcimx7d-sabre emulation with Linux v5.11 and later.
qemu-system-arm: ../system/memory.c:2750: memory_region_set_alias_offset: Assertion `mr->alias' failed.
Problem is that the Designware PCIe emulation accepts the full value range
for the iATU Viewport Register. However, both hardware and emulation only
support four inbound and four outbound viewports.
The Linux kernel determines the number of supported viewports by writing
0xff into the viewport register and reading the value back. The expected
value when reading the register is the highest supported viewport index.
Match that code by masking the supported viewport value range when the
register is written. With this change, the Linux kernel reports
imx6q-pcie 33800000.pcie: iATU: unroll F, 4 ob, 4 ib, align 0K, limit 4G
as expected and supported.
Fixes: d64e5eabc4 ("pci: Add support for Designware IP block")
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Nikita Ostrenkov <n.ostrenkov@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240129060055.2616989-1-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The npcm7xx Soc is created with a Cortex-A9 core, see in
hw/arm/npcm7xx.c:
static void npcm7xx_init(Object *obj)
{
NPCM7xxState *s = NPCM7XX(obj);
for (int i = 0; i < NPCM7XX_MAX_NUM_CPUS; i++) {
object_initialize_child(obj, "cpu[*]", &s->cpu[i],
ARM_CPU_TYPE_NAME("cortex-a9"));
}
The MachineClass::default_cpu_type field is ignored: delete it.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-8-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Musca boards use the embedded subsystems (SSE) tied to a specific
Cortex core. Our models only use the Cortex-M33.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Remove the now unused MachineClass::default_cpu_type field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-7-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M2Sxxx SoC family can only be used with Cortex-M3.
Propagating the CPU type from the board level is pointless.
Hard-code the CPU type at the SoC level.
Remove the now ignored MachineClass::default_cpu_type field.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-6-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Restrict MachineClass::valid_cpu_types[] to the single
valid CPU types.
Instead of ignoring invalid CPU type requested by the user:
$ qemu-system-arm -M midway -cpu cortex-a7 -S -monitor stdio
QEMU 8.2.50 monitor - type 'help' for more information
(qemu) info qom-tree
/machine (midway-machine)
/cpu[0] (cortex-a15-arm-cpu)
...
we now display an error:
$ qemu-system-arm -M midway -cpu cortex-a7
qemu-system-arm: Invalid CPU model: cortex-a7
The only valid type is: cortex-a15
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Restrict MachineClass::valid_cpu_types[] to the single
valid CPU type.
Instead of ignoring invalid CPU type requested by the user:
$ qemu-system-arm -M nuri -cpu cortex-a7 -S -monitor stdio
QEMU 8.2.50 monitor - type 'help' for more information
(qemu) info qom-tree
/machine (nuri-machine)
/soc (exynos4210)
/cpu[0] (cortex-a9-arm-cpu)
...
We now display an error:
$ qemu-system-arm -M nuri -cpu cortex-a7
qemu-system-arm: Invalid CPU model: cortex-a7
The only valid type is: cortex-a9
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
BusClass currently has transitional infrastructure to support
subclasses which implement the legacy BusClass::reset method rather
than the Resettable interface. We have now removed all the users of
BusClass::reset in the tree, so we can remove the transitional
infrastructure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-6-peter.maydell@linaro.org
Switch the s390x virtual-css bus from using BusClass::reset to the
Resettable interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-5-peter.maydell@linaro.org
Switch the ADB bus from using BusClass::reset to the Resettable
interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-4-peter.maydell@linaro.org
Switch vmbus from using BusClass::reset to the Resettable interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-3-peter.maydell@linaro.org
Switch the PCI bus from using BusClass::reset to the Resettable
interface.
This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-2-peter.maydell@linaro.org
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
-----BEGIN PGP SIGNATURE-----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=0C5S
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu into staging
aspeed queue:
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmW7Sa8ACgkQUaNDx8/7
# 7KG7mw/8DbMJY6aqgq5YANszzem1ktJphPCNxq081cbczCOUpCNX4aL+0/ANvxxD
# lbJQB+SZeIRmuFbxYPhq68rtzB4vG7tsQpns4H33EPKT4vuzF70lq4fgptMiun3q
# 1ZJ2LF3jonvQWdhbC17wzAQz0FFb4F7XOxz++UL4okPsgzsYItnd+TWs8q7+erRb
# 84UwN+eBTBAl/FiNk679/tBTqAfCVGgQ7dzotr4f3tg5POvrGOrlEjAn0O+dGGDj
# wgILmpEBsTsilRB1tz8Kw0j/v/VkHz1DJu45lRAV9CIrN22iKcjMilNGgNDT8kcI
# yAlxAw3iN+hVFqDov8wFPjDYd/Qw2oRAPy2Kd14hW9xL8zBOTms1JK5L0PS2+Feo
# ZjMJ2cOJq3t4Wt1ZXRhgHfF4ANwP0OZ/y9bHCy3CkBljEeiTQbikHP9gVV4qHXZH
# 4Q0HnDZQwAgobw3CmZ8jVx1dQueqy3ycuvkhCyv3S0l/tdbtXDtr5pNNu3dAP/PJ
# 3nifLdRImhDvxxO9GKaCdUVLzELzMJl0GrgAsVJPKVnKHA4IiVKmB+XcW9IUbfy/
# 3zA2wHJLrEF+MF6MsuNcEYCCqUvyNLm7rUrXk1wNLXpCJ35bbW5IYy7Ty/8E2GHb
# D5Cv/EPNhMBiNA4+HqQlMOTC13Ozv2qwCuWYCh2Ik8mnzaEiyTo=
# =0C5S
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Feb 2024 07:35:11 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu:
hw/fsi: Update MAINTAINER list
hw/fsi: Added FSI documentation
hw/fsi: Added qtest
hw/arm: Hook up FSI module in AST2600
hw/fsi: Aspeed APB2OPB & On-chip peripheral bus
hw/fsi: Introduce IBM's FSI master
hw/fsi: Introduce IBM's cfam
hw/fsi: Introduce IBM's fsi-slave model
hw/fsi: Introduce IBM's FSI Bus
hw/fsi: Introduce IBM's scratchpad device
hw/fsi: Introduce IBM's Local bus
hw/arm/aspeed: Check for CPU types in machine_run_board_init()
hw/arm/aspeed: Introduce aspeed_soc_cpu_type() helper
hw/arm/aspeed: Init CPU defaults in a common helper
hw/arm/aspeed: Set default CPU count using aspeed_soc_num_cpus()
hw/arm/aspeed: Remove dead code
tests/avocado/machine_aspeed.py: Update buildroot images to 2023.11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service
processor access to the internal buses of a host POWER processor to
perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage,
including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of
interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on buses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
The LBUS is modelled to maintain the qdev bus hierarchy and to take
advantage of the object model to automatically generate the CFAM
configuration block. The configuration block presents engines in the
order they are attached to the CFAM's LBUS. Engine implementations
should subclass the LBusDevice and set the 'config' member of
LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for
a CFAM to be simultaneously driven from multiple FSI links. The modeling
is not so complete; it's assumed that each CFAM is attached to a single
FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This
is not necessary to get FSI off the ground thanks to the mapping of the
CFAM address space onto the OPB address space - the models follow this
directly and map the CFAM memory region into the OPB's memory region.
Future work includes supporting more advanced accesses that drive the
FSI master directly rather than indirectly via the CFAM mapping, which
will require implementing the FSI state machine and methods for each of
the FSI symbols on the slave. Further down the track we can also look at
supporting the bitbanged SoftFSI drivers in Linux by extending the FSI
slave model to resolve sequences of GPIO IRQs into FSI symbols, and
calling the associated symbol method on the slave to map the access onto
the CFAM.
Testing:
Tested by reading cfam config address 0 on rainier machine type.
root@p10bmc:~# pdbg -a getcfam 0x0
p0: 0x0 = 0xc0022d15
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved FSIMasterState under AspeedAPB2OPBState
- modified fsi_opb_fsi_master_address() and
fsi_opb_opb2fsi_address()
- instroduced fsi_aspeed_apb2opb_init()
- reworked fsi_aspeed_apb2opb_realize()
- removed FSIMasterState object and fsi_opb_realize()
- simplified OPBus
- introduced fsi_aspeed_apb2opb_rw to fix endianness issue ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
This commit models the FSI master. CFAM is hanging out of FSI master which is a bus controller.
The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - move FSICFAMState object under FSIMasterState
- introduced fsi_master_init()
- reworked fsi_master_realize()
- dropped FSIBus definition ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on busses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c
- introduced fsi_cfam_instance_init()
- reworked fsi_cfam_realize() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where FSI bus is introduced.
The FSI bus is a simple bus where FSI master is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed include/hw/fsi/engine-scratchpad.h and
hw/fsi/engine-scratchpad.c
- dropped FSI_SCRATCHPAD
- included FSIBus definition
- dropped hw/fsi/trace-events changes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The scratchpad provides a set of non-functional registers. The firmware
is free to use them, hardware does not support any special management
support. The scratchpad registers can be read or written from LBUS
slave. The scratch pad is managed under FSI CFAM state.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The LBUS is modelled to maintain mapped memory for the devices. The
memory is mapped after CFAM config, peek table and FSI slave registers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed lbus_add_device() bc unused
- removed lbus_create_device() bc used only once
- removed "address" property
- updated meson.build to build fsi dir
- included an empty hw/fsi/trace-events ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Aspeed SoCs use a single CPU type (set as AspeedSoCClass::cpu_type).
Convert it to a NULL-terminated array (of a single non-NULL element).
Set MachineClass::valid_cpu_types[] to use the common machine code
to provide hints when the requested CPU is invalid (see commit
e702cbc19e ("machine: Improve is_cpu_type_supported()").
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to alter AspeedSoCClass::cpu_type in the next
commit, introduce the aspeed_soc_cpu_type() helper to
retrieve the per-SoC CPU type from AspeedSoCClass.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rework aspeed_soc_num_cpus() as a new init_cpus_defaults()
helper to reduce code duplication.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Since commit b7f1a0cb76 ("arm/aspeed: Compute the number
of CPUs from the SoC definition") Aspeed machines use the
aspeed_soc_num_cpus() helper to set the number of CPUs.
Use it for the ast1030-evb (commit 356b230ed1 "aspeed/soc:
Add AST1030 support") and supermicrox11-bmc (commit 40a38df55e
"hw/arm/aspeed: Add board model for Supermicro X11 BMC") machines.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Remove copy/paste typo from commit 6c323aba40 ("hw/arm/aspeed:
Adding new machine Tiogapass in QEMU").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAmW6NScPHG1qdEB0bHMu
bXNrLnJ1AAoJEHAbT2saaT5ZdQYH/2fhfhZotH0V2qAcMxlOoHbAE9UhZNRsSYtf
QFP0GXFYFAMm7LHkPUbvKgO7LylKWAOMn/zKZqgj1Vf1EpoKQ2FwLtR/buDz86Ec
pi2OrDPRA7Ay5c3ow3YZZkUOhQTTcR5rNjYctPtt/J4j8ol/z5vre7weJIg2bCJe
zI7vIVg7iFFzbkXY20KHngJ5nDC+aEm7WaGlxAP8kfkvy324Wy9O2k8qu2J5zbLT
HGvh3rwEDvRTYe4CaKFFHWNV0m4092HAr/dJBobugI5VZ6QQpK6Tgy8N+4ZrCHD2
SjUKeym85VTOYGuY8b18fk5MQK2SzsfBUJ4x8VGC75W4mJ8agdc=
=HImO
-----END PGP SIGNATURE-----
Merge tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu into staging
trivial patches for 2024-01-31
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAmW6NScPHG1qdEB0bHMu
# bXNrLnJ1AAoJEHAbT2saaT5ZdQYH/2fhfhZotH0V2qAcMxlOoHbAE9UhZNRsSYtf
# QFP0GXFYFAMm7LHkPUbvKgO7LylKWAOMn/zKZqgj1Vf1EpoKQ2FwLtR/buDz86Ec
# pi2OrDPRA7Ay5c3ow3YZZkUOhQTTcR5rNjYctPtt/J4j8ol/z5vre7weJIg2bCJe
# zI7vIVg7iFFzbkXY20KHngJ5nDC+aEm7WaGlxAP8kfkvy324Wy9O2k8qu2J5zbLT
# HGvh3rwEDvRTYe4CaKFFHWNV0m4092HAr/dJBobugI5VZ6QQpK6Tgy8N+4ZrCHD2
# SjUKeym85VTOYGuY8b18fk5MQK2SzsfBUJ4x8VGC75W4mJ8agdc=
# =HImO
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 31 Jan 2024 11:55:19 GMT
# gpg: using RSA key 7B73BAD68BE7A2C289314B22701B4F6B1A693E59
# gpg: issuer "mjt@tls.msk.ru"
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>" [full]
# gpg: aka "Michael Tokarev <mjt@corpit.ru>" [full]
# gpg: aka "Michael Tokarev <mjt@debian.org>" [full]
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D 4324 457C E0A0 8044 65C5
# Subkey fingerprint: 7B73 BAD6 8BE7 A2C2 8931 4B22 701B 4F6B 1A69 3E59
* tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu: (21 commits)
hw/hyperv: Include missing headers
hw/intc/xics: Include missing 'cpu.h' header
hw/arm: Add `\n` to hint message
hw/loongarch: Add `\n` to hint message
hw/i386: Add `\n` to hint message
backends/hostmem: Fix block comments style (checkpatch.pl warnings)
misc: Clean up includes
riscv: Clean up includes
cxl: Clean up includes
include: Clean up includes
m68k: Clean up includes
acpi: Clean up includes
aspeed: Clean up includes
disas/riscv: Clean up includes
hyperv: Clean up includes
scripts/clean-includes: Update exclude list
mailmap: Fix Stefan Weil email
qemu-docs: Update options for graphical frontends
qapi/migration.json: Fix the member name for MigrationCapability
colo: examples: remove mentions of script= and (wrong) downscript=
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In cases where a device tries to read more bytes than the block device
contains, the error is vague: "device requires X bytes, block backend
provides Y bytes".
This patch changes the errors of this function to include the block
backend name, the device id and device type name where appropriate.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 7260eadff22c08457740117c1bb7bd2b4353acb9.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a simple method to return some kind of human readable identifier for
use in error messages.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 8b566bfced98ae44be1fcc1f8e7215f0c3393aa1.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The following expression is incorrect because blk_pread_nonzeroes()
deals in units of bytes, not sectors:
bytes = MIN(size - offset, BDRV_REQUEST_MAX_SECTORS)
^^^^^^^
BDRV_REQUEST_MAX_BYTES is the appropriate constant.
Fixes: a4b15a8b9e ("pflash: Only read non-zero parts of backend image")
Cc: Xiang Zheng <zhengxiang9@huawei.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240130002712.257815-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Include missing headers in order to avoid when refactoring
unrelated headers:
hw/hyperv/hyperv.c:33:18: error: field ‘msg_page_mr’ has incomplete type
33 | MemoryRegion msg_page_mr;
| ^~~~~~~~~~~
hw/hyperv/hyperv.c: In function ‘synic_update’:
hw/hyperv/hyperv.c:64:13: error: implicit declaration of function ‘memory_region_del_subregion’ [-Werror=implicit-function-declaration]
64 | memory_region_del_subregion(get_system_memory(),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/hyperv/hyperv.c: In function ‘hyperv_hcall_signal_event’:
hw/hyperv/hyperv.c:683:17: error: implicit declaration of function ‘ldq_phys’; did you mean ‘ldub_phys’? [-Werror=implicit-function-declaration]
683 | param = ldq_phys(&address_space_memory, addr);
| ^~~~~~~~
| ldub_phys
hw/hyperv/hyperv.c:683:17: error: nested extern declaration of ‘ldq_phys’ [-Werror=nested-externs]
hw/hyperv/hyperv.c: In function ‘hyperv_hcall_retreive_dbg_data’:
hw/hyperv/hyperv.c:792:24: error: ‘TARGET_PAGE_SIZE’ undeclared (first use in this function); did you mean ‘TARGET_PAGE_BITS’?
792 | msg.u.recv.count = TARGET_PAGE_SIZE - sizeof(*debug_data_out);
| ^~~~~~~~~~~~~~~~
| TARGET_PAGE_BITS
hw/hyperv/hyperv.c: In function ‘hyperv_syndbg_send’:
hw/hyperv/hyperv.c:885:16: error: ‘HV_SYNDBG_STATUS_INVALID’ undeclared (first use in this function)
885 | return HV_SYNDBG_STATUS_INVALID;
| ^~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Include missing headers in order to avoid when refactoring
unrelated headers:
hw/intc/xics.c: In function 'icp_realize':
hw/intc/xics.c:304:5: error: unknown type name 'PowerPCCPU'
304 | PowerPCCPU *cpu;
| ^~~~~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes:
./scripts/clean-includes --git acpi include/hw/*/*acpi.h hw/*/*acpi.c
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Mark Kanda