Remove unneeded variables and setting value to 0 on zero initialised
data and replace check for error with error_fatal. Rationalise loop
that sets PCI config header fields read only.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <e4caf35ca10a68f5c74ae3f93fa0bcfa9457beea.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The vt82c686b-pm model can be shared between VT82C686B and VT8231. The
only difference between the two is the device id in what we emulate so
make an abstract via-pm model by renaming appropriately and add types
for vt82c686b-pm and vt8231-pm based on it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <34969fc7be984fa070479bfb9f748993a0aef31b.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This device is part of the multifunction VIA superio/south bridge chip
so not useful in itself.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <d0a806fed5e8055aee4fcf5b2f4790e6dd0f9dc6.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Similar to the SMBus io registers there is a power management io range
that is set via similar base address reg and enable bit. Some handling
of this was already there but with several problems: using the wrong
registers and bits, wrong size range, not acually updating mapping and
handling reset correctly, nor emulating any of the actual io
registers. Some of these errors are fixed up here.
After this patch we use the correct base address register, enable bit
and region size and allow guests to map/unmap this region, but we
still don't emulate any of the registers in this range.
PMD notes regarding the Configuration Space Power Management Registers:
- 0x40 General Configuration 0
- 0x41 General Configuration 1
. Bit 7: I/O Enable for ACPI I/O Base
- 0x48 Power Mgmt I/O Base
. Bit 0: Always set
. Bits 7-15: Power Management I/O Register Base Address
(this explains the change 0xffc0 -> 0xff80)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 4/4, added notes]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base address of the SMBus io ports and its enabled status is set
by registers in the PCI config space but this was not correctly
emulated. Instead the SMBus registers were mapped on realize to the
base address set by a property to the address expected by fuloong2e
firmware.
Fix the base and config register handling to more closely model
hardware which allows to remove the property and allows the guest to
control this mapping. Do all this in reset instead of realize so it's
correctly updated on reset.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <f2ca2ad5f08ba8cee07afd9d67b4e75cda21db09.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move lines around so that object definitions become consecutive and
not scattered around. This brings functions belonging to an object
together so it's clearer what is defined and what parts belong to
which object.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <9f942989dba46fc1c23b881f6cb135948f818c2f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The superio memory region holds the io space index/data registers used
to access the superio config registers that are implemented in struct
SuperIOConfig. To keep these related things together move the memory
region to SuperIOConfig and rename it accordingly.
Also remove the unused "data" member of SuperIOConfig which is not
needed as we store actual data values in the regs array.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <dc3c4e7632716ca73c10506bd02ee93b39c28705.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per core ISR is a set of 32-bit registers spaced by 8 bytes.
This patch fixed calculation of it's size and also added check
of alignment at reading & writing.
Fixes: Coverity CID 1438965 and CID 1438967
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Message-Id: <20210112012527.28927-1-jiaxun.yang@flygoat.com>
[PMD: Added Coverity CID]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Translate embedded assembly into IO writes which is more
readable.
Also hardcode cm_base at boot time instead of reading from CP0.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-5-jiaxun.yang@flygoat.com>
[PMD: Kept code comments]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here boston)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here fuloong2e)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add a bootloader helper to generate simple bootloaders for kernel.
It can help us reduce inline hex hack and also keep MIPS release 6
compatibility easier.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-2-jiaxun.yang@flygoat.com>
[PMD: Restricted bl_reg enum to C source,
inverted bl_gen_write() args,
added license in hw/mips/bootloader.h]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the loongson3 defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210122122404.11970-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
s->prnsts is updated in both branches of the if () else () statement.
Move the common bits outside so that it is cleaner.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1613447214-81951-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Unlike SD mode, when SD card is working in SPI mode, the argument
of CMD13 is stuff bits. Hence we should bypass the RCA check.
See "Physical Layer Specification Version 8.00", chapter 7.3.1.3
Detailed Command Description (SPI mode):
"The card shall ignore stuff bits and reserved bits in an argument"
and Table 7-3 Commands and Arguments (SPI mode):
"CMD13 Argument [31:0] stuff bits"
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in CMD24/25 for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in sd_erase() for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These APIs and macros may be referenced by functions that are
currently before them. Move them ahead a little bit.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, CMD30
response type is R1, not R1b.
Fixes: a1bb27b1e9 ("SD card emulation initial implementation")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, the
following commands:
- CMD28 (SET_WRITE_PROT)
- CMD29 (CLR_WRITE_PROT)
- CMD30 (SEND_WRITE_PROT)
are only supported by SDSC cards.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For high capacity memory cards, the erase start address and end
address are multiplied by 512, but the address check is still
based on the original block number in sd->erase_{start, end}.
Fixes: 1bd6fd8ed5 ("hw/sd/sdcard: Do not attempt to erase out of range addresses")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Besides CMD12, the following command's reponse type is R1b:
- SET_WRITE_PROT (CMD28)
- CLR_WRITE_PROT (CMD29)
- ERASE (CMD38)
Reuse the same s->stopping to indicate a R1b reponse is needed.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
CMD12's response type is R1b, which is basically a R1 plus optional
addition of the busy signal token that can be any number of bytes.
A zero value indicates card is busy and a non-zero value indicates
the card is ready for the next command.
Current implementation sends the busy signal token without sending
the R1 first. This does not break the U-Boot/Linux mmc_spi driver,
but it does not make the VxWorks driver happy.
Move the testing logic of s->stopping in the SSI_SD_RESPONSE state
a bit later, after the first byte of the card reponse is sent out,
to conform with the spec. After the busy signal token is sent, the
state should be transferred to SSI_SD_CMD.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210128063035.15674-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The SEND_IF_COND command (CMD8) response is of format R7, but
current code returns R1 for CMD8. Fix it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For a multiple block write operation, each block begins with a multi
write start token. Unlike the SD mode that the multiple block write
ends when receiving a STOP_TRAN command (CMD12), a special stop tran
token is used to signal the card.
Emulating this by manually sending a CMD12 to the SD card core, to
bring it out of the receiving data state.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-7-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add 2 more states for the block write operation. The SPI host needs
to send a data start token to start the transfer, and the data block
written to the card will be acknowledged by a data response token.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 6 -> 7]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present there is a data_ready() callback for the SD data read
path. Let's add a receive_ready() for the SD data write path.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the single/multiple block write in SPI mode is blocked
by sd_normal_command(). Remove the limitation.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The single block read (CMD17) codes are the same as the multiple
block read (CMD18). Merge them into one. The same applies to single
block write (CMD24) and multiple block write (CMD25).
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In the case of a multiple block read operation every transferred
block has its suffix of CRC16. Update the state machine logic to
handle multiple block read.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 5 -> 6]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When viewing/debugging memory regions it is sometimes hard to figure
out which PCI device something belongs to. Make the names unique by
including the vdev name in the name string.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20210213130325.14781-2-alex.bennee@linaro.org>
Without that wireshark complains about invalid control setup data
for non-control transfers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210216144939.841873-1-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In order to keep track of the alternate setting that should be used for
a given interface, the USBDevice struct keeps an array of alternate
setting values, which is indexed by the interface number. In
usb_host_set_interface, when this array is updated, usb_host_ep_update
is called as a result. However, when usb_host_ep_update accesses the
active libusb_config_descriptor, it indexes udev->altsetting with the
loop variable, rather than the interface number.
With the simple trace backend enable, this behavior can be seen:
[...]
usb_xhci_xfer_start 0.440 pid=1215 xfer=0x5596a4b85930 slotid=0x1 epid=0x1 streamid=0x0
usb_packet_state_change 1.703 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'undef' n=b'setup'
usb_host_req_control 2.269 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 req=0x10b value=0x1 index=0xd
usb_host_set_interface 0.449 pid=1215 bus=0x1 addr=0x5 interface=0xd alt=0x1
usb_host_parse_config 2542.648 pid=1215 bus=0x1 addr=0x5 value=0x2 active=0x1
usb_host_parse_interface 1.804 pid=1215 bus=0x1 addr=0x5 num=0xc alt=0x0 active=0x1
usb_host_parse_endpoint 2.012 pid=1215 bus=0x1 addr=0x5 ep=0x2 dir=b'in' type=b'int' active=0x1
usb_host_parse_interface 1.598 pid=1215 bus=0x1 addr=0x5 num=0xd alt=0x0 active=0x1
usb_host_req_emulated 3.593 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 status=0x0
usb_packet_state_change 2.550 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'setup' n=b'complete'
usb_xhci_xfer_success 4.298 pid=1215 xfer=0x5596a4b85930 bytes=0x0
[...]
In particular, it is seen that although usb_host_set_interface sets the
alternate setting of interface 0xd to 0x1, usb_host_ep_update uses 0x0
as the alternate setting due to using the incorrect index to
udev->altsetting.
Fix this problem by getting the interface number from the active
libusb_config_descriptor, and then using that as the index to
udev->altsetting.
Signed-off-by: Nick Rosbrook <rosbrookn@ainfosec.com>
Message-Id: <20210201213021.500277-1-rosbrookn@ainfosec.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When SEV-ES is enabled, it is not possible modify the guests register
state after it has been initially created, encrypted and measured.
Normally, an INIT-SIPI-SIPI request is used to boot the AP. However, the
hypervisor cannot emulate this because it cannot update the AP register
state. For the very first boot by an AP, the reset vector CS segment
value and the EIP value must be programmed before the register has been
encrypted and measured. Search the guest firmware for the guest for a
specific GUID that tells Qemu the value of the reset vector to use.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <22db2bfb4d6551aed661a9ae95b4fdbef613ca21.1611682609.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector. The table goes
backwards in memory so all entries are of the form
<data>|len|<GUID>
Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.
The foot of the table is of this form and <len> for this case
describes the entire size of the table. The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.
Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux blkfront expects both "discard-granularity" and
"discard-alignment" present on xenbus in order to properly enable the
feature, not exposing "discard-alignment" left some Linux blkfront
versions with a broken discard setup. This has also been addressed in
Linux with:
https://lore.kernel.org/lkml/20210118151528.81668-1-roger.pau@citrix.com/T/#u
Fix QEMU to report a "discard-alignment" of 0, in order for it to work
with older Linux frontends.
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Message-Id: <20210118153330.82324-1-roger.pau@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
cmd_fis is mapped as DMA_DIRECTION_FROM_DEVICE, however, it is read
from, and not written to anywhere. Fix the DMA_DIRECTION and mark
cmd_fis as read-only in the code.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210119164051.89268-1-alxndr@bu.edu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Copy bootinfo.h and bootinfo-mac.h from arch/m68k/include/uapi/asm/
to include/standard-headers/asm-m68k/
Imported from linux v5.9 but didn't change since v4.14 (header update)
and since v4.10 (content update).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20201220112615.933036-2-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Use nr_apu_cpus in favor of hard coding 2.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210210142048.3125878-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
BALATON Zoltan