The LoPAR spec provides no way for the guest kernel to report failure of
hotplug/hotunplug events. This wouldn't be bad if those operations were
granted to always succeed, but that's far for the reality.
What ends up happening is that, in the case of a failed hotunplug,
regardless of whether it was a QEMU error or a guest misbehavior, the
pSeries machine is retaining the unplug state of the device in the
running guest. This state is cleanup in machine reset, where it is
assumed that this state represents a device that is pending unplug, and
the device is hotunpluged from the board. Until the reset occurs, any
hotunplug operation of the same device is forbid because there is a
pending unplug state.
This behavior has at least one undesirable side effect. A long standing
pending unplug state is, more often than not, the result of a hotunplug
error. The user had to dealt with it, since retrying to unplug the
device is noy allowed, and then in the machine reset we're removing the
device from the guest. This means that we're failing the user twice -
failed to hotunplug when asked, then hotunplugged without notice.
Solutions to this problem range between trying to predict when the
hotunplug will fail and forbid the operation from the QEMU layer, from
opening up the IRQ queue to allow for multiple hotunplug attempts, from
telling the users to 'reboot the machine if something goes wrong'. The
first solution is flawed because we can't fully predict guest behavior
from QEMU, the second solution is a trial and error remediation that
counts on a hope that the unplug will eventually succeed, and the third
is ... well.
This patch introduces a crude, but effective solution to hotunplug
errors in the pSeries machine. For each unplug done, we'll timeout after
some time. If a certain amount of time passes, we'll cleanup the
hotunplug state from the machine. During the timeout period, any unplug
operations in the same device will still be blocked. After that, we'll
assume that the guest failed the operation, and allow the user to try
again. If the timeout is too short we'll prevent legitimate hotunplug
situations to occur, so we'll need to overestimate the regular time an
unplug operation takes to succeed to account that.
The true solution for the hotunplug errors in the pSeries machines is a
PAPR change to allow for the guest to warn the platform about it. For
now, the work done in this timeout design can be used for the new PAPR
'abort hcall' in the future, given that for both cases we'll need code
to cleanup the existing unplug states of the DRCs.
At this moment we're adding the basic wiring of the timer into the DRC.
Next patch will use the timer to timeout failed CPU hotunplugs.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The commit d03b174a83 (target/ppc: simplify bcdadd/sub functions)
meant to simplify some of the code but it inadvertently altered the
way the CR6 field is set after the operation has overflowed.
The CR6 bits are set based on the *unbounded* result of the operation,
so we need to look at the result before returning from bcd_add_mag,
otherwise we will look at 0 when it overflows.
Consider the following subtraction:
v0 = 0x9999999999999999999999999999999c (maximum positive BCD value)
v1 = 0x0000000000000000000000000000001d (negative one BCD value)
bcdsub. v0,v0,v1,0
The Power ISA 2.07B says:
If the unbounded result is greater than zero, do the following.
If PS=0, the sign code of the result is set to 0b1100.
If PS=1, the sign code of the result is set to 0b1111.
If the operation overflows, CR field 6 is set to 0b0101. Otherwise,
CR field 6 is set to 0b0100.
POWER9 hardware:
vr0 = 0x0000000000000000000000000000000c (positive zero BCD value)
cr6 = 0b0101 (0x5) (positive, overflow)
QEMU:
vr0 = 0x0000000000000000000000000000000c (positive zero BCD value)
cr6 = 0b0011 (0x3) (zero, overflow) <--- wrong
This patch reverts the part of d03b174a83 that introduced the
problem and adds a test-case to avoid further regressions:
before:
$ make run-tcg-tests-ppc64le-linux-user
(...)
TEST bcdsub on ppc64le
bcdsub: qemu/tests/tcg/ppc64le/bcdsub.c:58: test_bcdsub_gt:
Assertion `(cr >> 4) == ((1 << 2) | (1 << 0))' failed.
Fixes: d03b174a83 (target/ppc: simplify bcdadd/sub functions)
Reported-by: Paul Clarke <pc@us.ibm.com>
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20210222194035.2723056-1-farosas@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves the current documentation in files specific to each
platform family. PowerNV machine is updated, the other machines need
to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210222133956.156001-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
[dwg: Trivial capitalization fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_drc_detach() is not the best name for what the function does. The
function does not detach the DRC, it makes an uncommited attempt to do
it. It'll mark the DRC as pending unplug, via the 'unplug_request'
flag, and only if the DRC state is drck->empty_state it will detach the
DRC, via spapr_drc_release().
This is a contrast with its pair spapr_drc_attach(), where the function
is indeed creating the DRC QOM object. If you know what
spapr_drc_attach() does, you can be misled into thinking that
spapr_drc_detach() is removing the DRC from QEMU internal state, which
isn't true.
The current role of this function is better described as a request for
detach, since there's no guarantee that we're going to detach the DRC in
the end. Rename the function to spapr_drc_unplug_request to reflect
what is is doing.
The initial idea was to change the name to spapr_drc_detach_request(),
and later on change the unplug_request flag to detach_request. However,
unplug_request is a migratable boolean for a long time now and renaming
it is not worth the trouble. spapr_drc_unplug_request() setting
drc->unplug_request is more natural than spapr_drc_detach_request
setting drc->unplug_request.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When moving a physical DRC to "Available", drc_isolate_physical() will
move the DRC state to STATE_PHYSICAL_POWERON and, if the DRC is marked
for unplug, call spapr_drc_detach(). For physical DRCs,
drck->empty_state is STATE_PHYSICAL_POWERON, meaning that we're sure
that spapr_drc_detach() will end up calling spapr_drc_release() in the
end.
Likewise, for logical DRCs, drc_set_unusable will move the DRC to
"Unusable" state, setting drc->state to STATE_LOGICAL_UNUSABLE, which is
the drck->empty_state for logical DRCs. spapr_drc_detach() will call
spapr_drc_release() in this case as well.
In both scenarios, spapr_drc_detach() is being used as a
spapr_drc_release(), wrapper, where we also set unplug_requested (which
is already true, otherwise spapr_drc_detach() wouldn't be called in the
first place) and check if drc->state == drck->empty_state, which we also
know it's guaranteed to be true because we just set it.
Just use spapr_drc_release() in these functions to be clear of our
intentions in both these functions.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is mostly compiler warnings fixed but while doing this,
a bug in MIN() in tcgbios was found.
Alexey Kardashevskiy (14):
helpers: Define MIN()
libc: Compile with -Wextra
elf: Compile with -Wextra
usb: Compile with -Wextra
veth: Compile with -Wextra
virtio: Compile with -Wextra
e1000: Compile with -Wextra
libnet: Compile with -Wextra
libhv: Compile with -Wextra
libnvram: Compile with -Wextra
libtpm: Compile with -Wextra
slof/prim: Compile with -Wextra
Makefile: Actually compile with -Wextra
version: update to 20210217
Thomas Huth (1):
virtio-serial: Remove superfluous serial-* words
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
drc_isolate_logical() is used to move the DRC from the "Configured" to
the "Available" state, erroring out if the DRC is in the unexpected
"Unisolate" state and doing nothing (with RTAS_OUT_SUCCESS) if the DRC
is already in "Available" or in "Unusable" state.
When moving from "Configured" to "Available", the DRC is moved to the
LOGICAL_AVAILABLE state, a drc->unplug_requested check is done and, if
true, spapr_drc_detach() is called.
What spapr_drc_detach() does then is:
- set drc->unplug_requested to true. In fact, this is the only place
where unplug_request is set to true;
- does nothing else if drc->state != drck->empty_state. If the DRC
state is equal to drck->empty_state, spapr_drc_release() is
called. For logical DRCs, drck->empty_state = LOGICAL_UNUSABLE.
In short, calling spapr_drc_detach() in drc_isolate_logical() does
nothing. It'll set unplug_request to true again ('again' since it was
already true - otherwise the function wouldn't be called), and will
return without calling spapr_drc_release() because the DRC is not in
LOGICAL_UNUSABLE, since drc_isolate_logical() just moved it to
LOGICAL_AVAILABLE. The only place where the logical DRC is released is
when called from drc_set_unusable(), when it is moved to the
"Unusable" state. As it should, according to PAPR.
Even though calling spapr_drc_detach() in drc_isolate_logical() is
benign, removing it will avoid further thought about the matter. So
let's go ahead and do that.
As a note, this logic was introduced in commit bbf5c878ab. Since
then, the DRC handling code was refactored and enhanced, and PAPR
itself went through some changes in the DRC area as well. It is
expected that some assumptions we had back then are now deprecated.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210211225246.17315-2-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We no longer need to include sm501_template.h multiple times, so
we can simply inline its contents into sm501.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-4-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that we only include sm501_template.h for the DEPTH==32 case, we
can expand out the uses of the BPP, PIXEL_TYPE and PIXEL_NAME macros
in that header.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-3-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the sm501 display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210212180653.27588-2-peter.maydell@linaro.org>
Acked-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Milkymist board requires more than the PTIMER. Directly
select the LM32_DEVICES. This fixes:
/usr/bin/ld:
libqemu-lm32-softmmu.fa.p/target_lm32_gdbstub.c.o: in function `lm32_cpu_gdb_read_register':
target/lm32/gdbstub.c:46: undefined reference to `lm32_pic_get_im'
target/lm32/gdbstub.c:48: undefined reference to `lm32_pic_get_ip'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_im':
target/lm32/op_helper.c:107: undefined reference to `lm32_pic_set_im'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_ip':
target/lm32/op_helper.c:114: undefined reference to `lm32_pic_set_ip'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_jtx':
target/lm32/op_helper.c:120: undefined reference to `lm32_juart_set_jtx'
libqemu-lm32-softmmu.fa.p/target_lm32_op_helper.c.o: in function `helper_wcsr_jrx':
target/lm32/op_helper.c:125: undefined reference to `lm32_juart_set_jrx'
libqemu-lm32-softmmu.fa.p/target_lm32_translate.c.o: in function `lm32_cpu_dump_state':
target/lm32/translate.c:1161: undefined reference to `lm32_pic_get_ip'
target/lm32/translate.c:1161: undefined reference to `lm32_pic_get_im'
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210221225626.2589247-4-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We want to be able to use the 'LM32' config for architecture
specific features. As CONFIG_LM32 is only used to select
peripherals, rename it CONFIG_LM32_DEVICES.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210221225626.2589247-3-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We want to be able to use the 'LM32' config for architecture
specific features. Introduce CONFIG_LM32_EVR to select the
lm32-evr / lm32-uclinux boards.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210221225626.2589247-2-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Update the common copyright string that we use in
-version reports, About dialogs, etc, to 2021.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210309162258.28633-1-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Follow the inclusive terminology from the "Conscious Language in your
Open Source Projects" guidelines [*] and replace the word "blacklist"
appropriately.
[*] https://github.com/conscious-lang/conscious-lang-docs/blob/main/faq.md
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210303184644.1639691-6-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Follow the inclusive terminology from the "Conscious Language in your
Open Source Projects" guidelines [*] and replace the word "blacklist"
appropriately.
[*] https://github.com/conscious-lang/conscious-lang-docs/blob/main/faq.md
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210303184644.1639691-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Follow the inclusive terminology from the "Conscious Language in your
Open Source Projects" guidelines [*] and replace the word "blacklist"
appropriately.
[*] https://github.com/conscious-lang/conscious-lang-docs/blob/main/faq.md
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210303184644.1639691-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Follow the inclusive terminology from the "Conscious Language in your
Open Source Projects" guidelines [*] and replace the words "whitelist"
appropriately.
[*] https://github.com/conscious-lang/conscious-lang-docs/blob/main/faq.md
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210303184644.1639691-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Follow the inclusive terminology from the "Conscious Language in your
Open Source Projects" guidelines [*] and replace the words "whitelist"
appropriately.
[*] https://github.com/conscious-lang/conscious-lang-docs/blob/main/faq.md
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303184644.1639691-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We forward-declare Object typedef in "qemu/typedefs.h" since commit
ca27b5eb7c ("qom/object: Move Object typedef to 'qemu/typedefs.h'").
Use it everywhere to make the code simpler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210225182003.3629342-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These flags cause the output to look strange for 'make check', and
they aren't needed to reproduce bugs, if they reappear.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210216181316.794276-1-alxndr@bu.edu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We already got a global function called id_generate() to create unique
IDs within QEMU. Let's use it in the network subsytem, too, instead of
inventing our own ID scheme here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210215090225.1046239-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The qemu-img.rst, qemu-nbd.rst, virtfs-proxy-helper.rst, qemu-trace-stap.rst,
and virtiofsd.rst manuals were moved to docs/tools, so this update MAINTAINERS
accordingly.
Fixes: a08b4a9fe6 ("docs: Move tools documentation to tools manual")
Signed-off-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210204135425.1380280-1-wainersm@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When dbus_vmstate_post_load() fails, it complains to stderr. Except
on short read, where it checks with g_return_val_if_fail(). This
fails silently if G_DISABLE_CHECKS is undefined (it should be), or
else pads the short read with uninitialized bytes.
Replace g_return_val_if_fail() by a proper error check.
Fixes: 5010cec2bc
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210126124240.2081959-2-armbru@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
On Fedora 33, gcc 10.2.1 notes that scsi_cdb_length(buf) can set
len==-1, which in turn overflows g_malloc():
[5/5] Linking target qemu-system-x86_64
In function ‘scsi_disk_new_request_dump’,
inlined from ‘scsi_new_request’ at ../hw/scsi/scsi-disk.c:2608:9:
../hw/scsi/scsi-disk.c:2582:19: warning: argument 1 value ‘18446744073709551612’ exceeds maximum object size 9223372036854775807 [-Walloc-size-larger-than=]
2582 | line_buffer = g_malloc(len * 5 + 1);
| ^
Silence it with a decent assertion, since we only convert a buffer to
bytes when we have a valid cdb length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210209152350.207958-1-eblake@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
An assorted set of spelling fixes in various places.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210309111510.79495-1-mjt@msgid.tls.msk.ru>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAmBEwfEeHG1hcmsuY2F2
ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIfYZYH/AwOuqycV9XI1s3K
valsExtSmcj6oTrFTSyak0U7QL9G5pm40qEHwQkwFwYecaQXfFNMN1Mt4gYpsLai
JNhV29tzWrQtNFepCjvvuJihDY5IC/3NWyrWqYXRNZ5IGMvde3HUcg210bFOC3mf
iOtZ40ZjBspTwG4eJCOLBBDeXVAMkVUjdfqtsq66zGteHsJjNEpso0HLdMvlFkud
QLF4g06h8iFMxwahZYEwY+fKUHphqfZn8INr01ODQIy3nBGVgenKz9DKPw/pg/UD
nfxhuYwftDof65JpYEhClOWas3AztFJ1YyyP/cibwosLBQVphj3R05/kF6VuyuyP
gZjux0w=
=RPt3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mcayland/tags/qemu-sparc-20210307' into staging
qemu-sparc queue
# gpg: Signature made Sun 07 Mar 2021 12:07:13 GMT
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* remotes/mcayland/tags/qemu-sparc-20210307: (42 commits)
esp: add support for unaligned accesses
esp: implement non-DMA transfers in PDMA mode
esp: add trivial implementation of the ESP_RFLAGS register
esp: convert cmdbuf from array to Fifo8
esp: convert ti_buf from array to Fifo8
esp: transition to message out phase after SATN and stop command
esp: add maxlen parameter to get_cmd()
esp: raise interrupt after every non-DMA byte transferred to the FIFO
esp: remove old deferred command completion mechanism
esp: defer command completion interrupt on incoming data transfers
esp: latch individual bits in ESP_RINTR register
esp: implement FIFO flush command
esp: add 4 byte PDMA read and write transfers
esp: remove pdma_origin from ESPState
esp: use FIFO for PDMA transfers between initiator and device
esp: fix PDMA target selection
esp: rename get_cmd_cb() to esp_select()
esp: remove CMD pdma_origin
esp: use in-built TC to determine PDMA transfer length
esp: use ti_wptr/ti_rptr to manage the current FIFO position for PDMA
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2600 allocates distinct GIC IRQs for the LPC subdevices such as
the iBT device. Previously on the AST2400 and AST2500 the LPC subdevices
shared a single LPC IRQ.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-4-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The datasheet says we have 197 IRQs allocated, and we need more than 128
to describe IRQs from LPC devices. Raise the value now to allow
modelling of the LPC devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This appears to be a requirement of the GIC model. The AST2600 allocates
197 GIC IRQs, which we will adjust shortly.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Firmware images can be found on the OpenBMC jenkins site and on the
OpenBMC GitHub release page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210303072743.1551329-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ast2600 machines do not have PSCI firmware, so this property should
have never been set. Removing this node fixes SMP booting Linux kernels
that have PSCI enabled, as Linux fails to find PSCI in the device tree
and falls back to the soc-specific method for enabling secondary CPUs.
The comment is out of date as Qemu has supported -kernel booting since
9bb6d14081 ("aspeed: Add boot stub for smp booting"), in v5.1.
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210303010505.635621-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The FreeBSD project has a number of enhancements to bsd-user. These changes have
evolved over the past 10 year, and aren't currently updated to the latest
version of qemu due to fluxuations in staffing causing us to fall behind in the
past. We're working on porting all the changes forward and contributing all the
changes back to qemu. Add myself as maintainer and Kyle Evans as a reviewer for
changes. In addition, add a pointer to our github repo in the interim while this
work is ongoing.
Signed-off-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210308224023.75187-1-imp@bsdimp.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
TILE-Gx was only implemented in linux-user mode, but support for this CPU
was removed from the upstream Linux kernel in 2018, and it has also been
dropped from glibc, so there is no new Linux development taking place with
this architecture. For running the old binaries, users can simply use older
versions of QEMU.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210224183952.80463-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Previously, tests were being filtered by the matching target
architectures to be built. The benefit, compared to the current
situation, is a more concise test job that won't show tests canceled
because a matching QEMU binary was not found (those tests won't even
be attempted).
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Message-Id: <20210225232122.1254879-3-crosa@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "get-vm-images" target defined in tests/Makefile.include is a
prerequisite for "check-acceptance", so that those files get
downloaded before the Avocado job even starts.
It looks like on c401c058a1 a TARGETS variable was introduced with a
different content than it was previously coming from the main
Makefile. From that point on, the "get-vm-images" succeed without
doing anything because there was no matching architecture to download.
This restores the download of images (that match targets to be built)
before the job starts, eliminating downloads and their associated
failures during the tests.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Message-Id: <20210225232122.1254879-2-crosa@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Improve current qgraph documentation with a more concrete example
and clearer motivation.
This patch depends on the previous serie
"libqos/qgraph: format qgraph comments for sphinx documentation"
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20210301092432.20342-1-eesposit@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Change documentation style and fix minor typos in tests/qtest/libqos/qgraph.h
to automatically generate sphinx documentation in docs/devel/qgraph.rst
The mechanism explanation that once was in qgraph.h is now moved to qgraph.rst
There is no functional change intended.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20210308073240.6363-1-eesposit@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Support Identify command for Namespace attached controller list. This
command handler will traverse the controller instances in the given
subsystem to figure out whether the specified nsid is attached to the
controllers or not.
The 4096bytes Identify data will return with the first entry (16bits)
indicating the number of the controller id entries. So, the data can
hold up to 2047 entries for the controller ids.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
[k.jensen: rebased for dma refactor]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If namespace inventory is changed due to some reasons (e.g., namespace
attachment/detachment), controller can send out event notifier to the
host to manage namespaces.
This patch sends out the AEN to the host after either attach or detach
namespaces from controllers. To support clear of the event from the
controller, this patch also implemented Get Log Page command for Changed
Namespace List log type. To return namespace id list through the
command, when namespace inventory is updated, id is added to the
per-controller list (changed_ns_list).
To indicate the support of this async event, this patch set
OAES(Optional Asynchronous Events Supported) in Identify Controller data
structure.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch supports Namespace Attachment command for the pre-defined
nvme-ns device nodes. Of course, attach/detach namespace should only be
supported in case 'subsys' is given. This is because if we detach a
namespace from a controller, somebody needs to manage the detached, but
allocated namespace in the NVMe subsystem.
As command effect for the namespace attachment command is registered,
the host will be notified that namespace inventory is changed so that
host will rescan the namespace inventory after this command. For
example, kernel driver manages this command effect via passthru IOCTL.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
[k.jensen: rebased for dma refactor]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch has no functional changes. This patch just refactored
nvme_select_ns_iocs() to iterate the attached namespaces of the
controlller and make it invoke __nvme_select_ns_iocs().
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Daniel Henrique Barboza