MacOS X uses multiple techniques for calibrating timers depending upon the detected
hardware. One of these calibration routines compares the change in the timebase
against the KeyLargo timer and uses this to recalculate the clock frequency,
timebase frequency and bus frequency if the calibration exceeds certain limits.
This recalibration occurs despite the correct values being passed via the device
tree, and is likely due to buggy firmware on some hardware.
The timebase frequency of 100MHz was set way back in 2005 by commit fa296b0fb4
("PIC fix - changed back TB frequency to 100 MHz") and with this value on a
mac99,via=pmu machine the OSX 10.2 timer calibration incorrectly calculates the
bus frequency as 400MHz instead of 100MHz. The most noticeable side-effect is
the UI appears sluggish and not very responsive for normal use.
Change the timebase frequency from 100MHz to 25MHz which matches that of a real
G4 AGP machine (the closest match to QEMU's mac99 machine) and allows OSX 10.2
to correctly detect all of the clock frequency, timebase frequency and bus
frequency.
Tested on various MacOS images from OS 9.2 through to OSX 10.4, along with Linux
and NetBSD and I was unable to find any regressions from this change.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240304073548.2098806-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Introduce a new enum type property allowing to set an
IOMMU granule. Values are 4k, 8k, 16k, 64k and host.
This latter indicates the vIOMMU granule will match
the host page size.
A subsequent patch will add such a property to the
virtio-iommu device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240227165730.14099-2-eric.auger@redhat.com>
deliver_bitmask is allocated on the heap in apic_deliver(), but there
are many paths in the function that return before the corresponding
g_free() is reached. Fix this by switching to g_autofree and, while at
it, also switch to g_new. Do the same in apic_deliver_irq() as well
for consistency.
Fixes: b5ee0468e9 ("apic: add support for x2APIC mode", 2024-02-14)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-ID: <20240304224133.267640-1-pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The "isapc" machine only provides an ISA bus, not a PCI one,
and doesn't instanciate any i440FX south bridge.
Its machine class defines PCMachineClass::pci_enabled = false,
and pc_init1() only uses the pci_type argument when pci_enabled
is true. Since for this machine the argument is not used,
passing NULL makes more sense.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240301185936.95175-5-philmd@linaro.org>
All callers use host_type=TYPE_I440FX_PCI_HOST_BRIDGE.
Directly use this definition within pc_init1().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240301185936.95175-4-philmd@linaro.org>
NotifyVmexitOption_str() is QAPI-generated in
"qapi/qapi-types-run-state.h", which "sysemu/runstate.h"
already includes.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240301185936.95175-3-philmd@linaro.org>
As the comment in qapi/error, passing @errp to error_prepend() requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
...
* - It should not be passed to error_prepend(), error_vprepend() or
* error_append_hint(), because that doesn't work with &error_fatal.
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
ERRP_GUARD() could avoid the case when @errp is the pointer of
error_fatal, the user can't see this additional information, because
exit() happens in error_setg earlier than information is added [1].
The remote_object_set_fd() passes @errp to error_prepend(), and as a
PropertyInfo.set method, its @errp is so widely sourced that it is
necessary to protect it with ERRP_GUARD().
To avoid the issue like [1] said, add missing ERRP_GUARD() at the
beginning of this function.
[1]: Issue description in the commit message of commit ae7c80a7bd
("error: New macro ERRP_GUARD()").
Cc: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Cc: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240229143914.1977550-4-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As the comment in qapi/error, passing @errp to error_prepend() requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
...
* - It should not be passed to error_prepend(), error_vprepend() or
* error_append_hint(), because that doesn't work with &error_fatal.
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
ERRP_GUARD() could avoid the case when @errp is the pointer of
error_fatal, the user can't see this additional information, because
exit() happens in error_setg earlier than information is added [1].
The xen_netdev_connect() passes @errp to error_prepend(), and its @errp
parameter is from xen_device_frontend_changed().
Though its @errp points to @local_err of xen_device_frontend_changed(),
to follow the requirement of @errp, add missing ERRP_GUARD() at the
beginning of this function.
[1]: Issue description in the commit message of commit ae7c80a7bd
("error: New macro ERRP_GUARD()").
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paul Durrant <paul@xen.org>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240229143914.1977550-3-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As the comment in qapi/error, passing @errp to error_prepend() requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
...
* - It should not be passed to error_prepend(), error_vprepend() or
* error_append_hint(), because that doesn't work with &error_fatal.
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
ERRP_GUARD() could avoid the case when @errp is the pointer of
error_fatal, the user can't see this additional information, because
exit() happens in error_setg earlier than information is added [1].
The xen_console_connect() passes @errp to error_prepend() without
ERRP_GUARD().
There're 2 places will call xen_console_connect():
- xen_console_realize(): the @errp is from DeviceClass.realize()'s
parameter.
- xen_console_frontend_changed(): the @errp points its caller's
@local_err.
To avoid the issue like [1] said, add missing ERRP_GUARD() at the
beginning of xen_console_connect().
[1]: Issue description in the commit message of commit ae7c80a7bd
("error: New macro ERRP_GUARD()").
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paul Durrant <paul@xen.org>
Cc: "Marc-André Lureau" <marcandre.lureau@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-ID: <20240228163723.1775791-15-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In order to build this file once for all targets, replace:
TARGET_PAGE_BITS -> qemu_target_page_bits()
TARGET_PAGE_SIZE -> qemu_target_page_size()
TARGET_PAGE_MASK -> -qemu_target_page_size()
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20231114163123.74888-4-philmd@linaro.org>
We are going to replace TARGET_PAGE_MASK by a
runtime variable. In order to reduce code duplication,
propagate TARGET_PAGE_MASK to get_physmapping() and
xen_phys_offset_to_gaddr().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20231114163123.74888-3-philmd@linaro.org>
Use TARGET_PAGE_SIZE to calculate TARGET_PAGE_ALIGN.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20231114163123.74888-2-philmd@linaro.org>
xen-hvm.c calls xc_set_hvm_param() from <xenctrl.h>,
so better compile it with Xen CPPFLAGS.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20231114143816.71079-19-philmd@linaro.org>
"hw/xen/xen_pt.h" requires "hw/xen/xen_native.h" which is target
specific. It also declares IGD methods, which are not target
specific.
Target-agnostic code can use IGD methods. To allow that, extract
these methos into a new "hw/xen/xen_igd.h" header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20231114143816.71079-18-philmd@linaro.org>
Commit eaab4d60d3 ("Introduce Xen PCI Passthrough, qdevice")
introduced both xen_pt.[ch], but only added the license to
xen_pt.c. Use the same license for xen_pt.h.
Suggested-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20231114143816.71079-17-philmd@linaro.org>
Instead of the target-specific TARGET_PAGE_BITS definition,
use qemu_target_page_bits() which is target agnostic.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20231114143816.71079-15-philmd@linaro.org>
To avoid a potential global variable shadow in
hw/i386/pc_piix.c::pc_init1(), rename Xen's
"ram_memory" as "xen_memory".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20231114143816.71079-11-philmd@linaro.org>
Similarly to the restriction in hw/pci/msix.c (see commit
e1e4bf2252 "msix: fix msix_vector_masked"), restrict the
xen_is_pirq_msi() call in msi_is_masked() to Xen.
No functional change intended.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20231114143816.71079-7-philmd@linaro.org>
vAPIC isn't KVM specific, so having its name prefixed 'kvm'
is misleading. Rename it simply 'vapic'. Rename the single
function prefixed 'kvm'.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230905145159.7898-1-philmd@linaro.org>
MCFG segments should point to PCI configuration range, not BAR MMIO.
Signed-off-by: Ilya Chugin <danger_mail@list.ru>
Fixes: 55ecd83b36 ("hw/riscv/virt-acpi-build.c: Add IO controllers and devices")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Message-ID: <180d236d-c8e4-411a-b4d2-632eb82092fa@list.ru>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The reads to in_clrip[x] registers return rectified input values of the
interrupt sources.
A rectified input value of an interrupt source is defined by the section
"4.5.2 Source configurations (sourcecfg[1]–sourcecfg[1023])" of the RISC-V
AIA specification as:
"rectified input value = (incoming wire value) XOR (source is inverted)"
Update the riscv_aplic_read_input_word() implementation to match the above.
Fixes: e8f79343cf ("hw/intc: Add RISC-V AIA APLIC device emulation")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240306095722.463296-3-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The writes to setipnum_le register in APLIC MSI-mode have special
consideration for level-triggered interrupts as-per section "4.9.2
Special consideration for level-sensitive interrupt sources" of the
RISC-V AIA specification.
Particularly, the below text from the RISC-V specification defines
the behaviour of writes to setipnum_le for level-triggered interrupts:
"A second option is for the interrupt service routine to write the
APLIC’s source identity number for the interrupt to the domain’s
setipnum register just before exiting. This will cause the interrupt’s
pending bit to be set to one again if the source is still asserting
an interrupt, but not if the source is not asserting an interrupt."
Fix setipnum_le write emulation for APLIC MSI-mode by implementing
the above behaviour in riscv_aplic_set_pending() function.
Fixes: e8f79343cf ("hw/intc: Add RISC-V AIA APLIC device emulation")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240306095722.463296-2-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 'virt' machine makes assumptions on the Advanced Core-Local
Interruptor, or aclint, based on 'tcg_enabled()' conditionals. This
will impact MSI related tests support when adding a RISC-V 'virt' libqos
machine. The accelerator used in that case, 'qtest', isn't being
accounted for and we'll error out if we try to enable aclint.
Create a new virt_aclint_allowed() helper to gate the aclint code
considering both TCG and 'qtest' accelerators. The error message is
left untouched, mentioning TCG only, because we don't expect the
regular user to be aware of 'qtest'.
We want to add 'qtest' support for aclint only, leaving the TCG specific
bits out of it. This is done by changing the current format we use
today:
if (tcg_enabled()) {
if (s->have_aclint) { - aclint logic - }
else { - non-aclint, TCG logic - }
}
into:
if (virt_aclint_allowed() && s->have_aclint) {
- aclint logic -
} else if (tcg_enabled()) {
- non-aclint, TCG logic -
}
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240217192607.32565-6-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We want to add a RISC-V 'virt' libqos machine to increase our test
coverage. Some of the tests will try to plug a virtio-iommu-pci
device into the board and do some tests with it.
Enable virtio-iommu-pci in the 'virt' machine.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240217192607.32565-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Hotplugged FDT nodes will attempt to write this node that, at this
moment, is being created only in create_fdt_pcie() during
finalize_fdt().
Create it earlier.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240217192607.32565-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Enable ACPI NUMA support by adding the following 2 ACPI tables:
SRAT: provides the association for memory/Harts and Proximity Domains
SLIT: provides the relative distance between Proximity Domains
The SRAT RINTC Affinity Structure definition[1] was based on the recently
approved ACPI CodeFirst ECR[2].
[1] https://github.com/riscv-non-isa/riscv-acpi/issues/25
[2] https://mantis.uefi.org/mantis/view.php?id=2433
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240129094200.3581037-1-haibo1.xu@intel.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, the initrd is placed at 128MB, which overlaps with the kernel
when it is large (for example syzbot kernels are). From the kernel side,
there is no reason we could not push the initrd further away in memory
to accommodate large kernels, so move the initrd at 512MB when possible.
The ideal solution would have been to place the initrd based on the
kernel size but we actually can't since the bss size is not known when
the image is loaded by load_image_targphys_as() and the initrd would
then overlap with this section.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240206154042.514698-1-alexghiti@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Generate Serial Port Console Redirection Table (SPCR) for RISC-V
virtual machine.
Signed-off-by: Sia Jee Heng <jeeheng.sia@starfivetech.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240129021440.17640-3-jeeheng.sia@starfivetech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V should also generate the SPCR in a manner similar to ARM.
Therefore, instead of replicating the code, relocate this function
to the common AML build.
Signed-off-by: Sia Jee Heng <jeeheng.sia@starfivetech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240129021440.17640-2-jeeheng.sia@starfivetech.com>
[ Changes by AF:
- Add missing Language SPCR entry
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The sun4v RTC device model added under commit a0e893039c in 2016
was unfortunately added with a license of GPL-v3-or-later, which is
not compatible with other QEMU code which has a GPL-v2-only license.
Relicense the code in the .c and the .h file to GPL-v2-or-later,
to make it compatible with the rest of QEMU.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini (for Red Hat) <pbonzini@redhat.com>
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240223161300.938542-1-peter.maydell@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externally" (using input
irqs) results in an out irq (transmitted to SYSCFG)
- output mode : setting a bit in ODR sets the corresponding out irq
(if this line is configured in output mode)
- pull-up, pull-down
- push-pull, open-drain
Difference with the real GPIOs :
- Alternate Function and Analog mode aren't implemented :
pins in AF/Analog behave like pins in input mode
- floating pins stay at their last value
- register IDR reset values differ from the real one :
values are coherent with the other registers reset values
and the fact that AF/Analog modes aren't implemented
- setting I/O output speed isn't supported
- locking port bits isn't supported
- ADC function isn't supported
- GPIOH has 16 pins instead of 2 pins
- writing to registers LCKR, AFRL, AFRH and ASCR is ineffective
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240305210444.310665-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we can generate reliable clock frequencies from the RCC, remove
the hacky definition of the sysclk in the b_l475e_iot01a initialisation
code and use the correct RCC clock.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240303140643.81957-8-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add write protections for the fields in the CR register.
PLL configuration write protections (among others) have not
been handled yet. This is planned in a future patch set.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-7-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Update the RCC state and propagate frequency changes when writing to the
RCC registers. Currently, ICSCR, CIER, the reset registers and the stop
mode registers are not implemented.
Some fields have not been implemented due to uncertainty about
how to handle them (Like the clock security system or bypassing
mecanisms).
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-6-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate the whole clock tree and using the Clock multiplexers and
the PLLs defined in the previous commits. This allows to statically
define the clock tree and easily follow the clock signal from one end to
another.
Also handle three-phase reset now that we have defined a known base
state for every object.
(Reset handling based on hw/misc/zynq_sclr.c)
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-5-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This object represents the PLLs and their channels. The PLLs allow for a
more fine-grained control of the clocks frequency.
The migration handling is based on hw/misc/zynq_sclr.c.
Three phase reset will be handled in a later commit.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-4-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This object is used to represent every multiplexer in the clock tree as
well as every clock output, every presecaler, frequency multiplier, etc.
This allows to use a generic approach for every component of the clock tree
(except the PLLs).
The migration handling is based on hw/misc/zynq_sclr.c.
Three phase reset will be handled in a later commit.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240303140643.81957-3-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Add the necessary files to add a simple RCC implementation with just
reads from and writes to registers. Also instantiate the RCC in the
STM32L4x5_SoC. It is needed for accurate emulation of all the SoC
clocks and timers.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240303140643.81957-2-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds loopback for sent characters, sent BREAK,
and modem-control signals.
Loopback of send and modem-control is often used for uart
self tests in real hardware but missing from current pl011
model, resulting in self-test failures when running in QEMU.
This implementation matches what is observed in real pl011
hardware placed in loopback mode:
1. Input characters and BREAK events from serial backend
are ignored, but
2. Both TX characters and BREAK events are still sent to
serial backend, in addition to be looped back to RX.
Signed-off-by: Tong Ho <tong.ho@amd.com>
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20240227054855.44204-1-tong.ho@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
BCM2835 has three I2C controllers. All of them share the same interrupt line.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240224191038.2409945-3-rayhan.faizel@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A few deficiencies in the current device model need to be noted.
1. FIFOs are not used. All sends and receives are done directly.
2. Repeated starts are not emulated. Repeated starts can be triggered in real
hardware by sending a new read transfer request in the window time between
transfer active set of write transfer request and done bit set of the same.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240224191038.2409945-2-rayhan.faizel@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix GIC settings when using --without-default-devices
* Fix USB PCAP streams on Windows
* Remove temporary files from test-util-sockets
* Fix TLS io channels sending too much data to the backend
-----BEGIN PGP SIGNATURE-----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=9JAI
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-03-01' of https://gitlab.com/thuth/qemu into staging
* Fix some bugs in the vring setup of libqos
* Fix GIC settings when using --without-default-devices
* Fix USB PCAP streams on Windows
* Remove temporary files from test-util-sockets
* Fix TLS io channels sending too much data to the backend
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmXhjBcRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWzZw/+OTSsKg6JTX0z3fjL6If+Ns/EnFiniHHI
# y1jR7fPub3ybFokgHIWrRVG+9ol+1tJuPlO5Bsx1SKFzNC8++l1iyK7E25xnmp2P
# Ry/Z0ZSWp3JWCtLm6km5pKl3wWI9p0XwfUOJbCWYM5dOsd2a4C4DSvjcwNXR7pTB
# 4AxXFj5G5UwXuffgPnBzeerm5baNweSqa/uczUY6Od+iJwmHpaSk0SJ4NIlIYvnS
# z3BH81trQAoKYZyywp0aF+jH9w3YNwD1XDp2Bcf3qSWDdokN55V13yyiSllTfUwX
# Lq3fotoLqFJL0A4m8a3TdCKMP8ReoJATSriPHJmGMgqWGTnvtRBIsx1pmMpYRB6U
# EltaKW0WXeQAad0ZYGl4odx7kQUQjdc8HTQRTevQD9g3XpZZN0o9MfTPdM2eR5h6
# xaS8UEc61YJAcmD27Ir92JGGGMLBTYz4OGLx3Rj7l7S759GQ67qih9TGcE9nqSj+
# +wAHfiOjUZnSWnp7Hq4M/TIjNh0BuyBW4oRBASaikjjQ82Hih5bPTdRu1J8lYuXC
# PhN8dLwdk0NMrnnHuFDKq/sXjDeXF3Hg0AmtVvOGiB2z2OeVSPtMxl/YgniGVTbj
# CHXDqDrBAa7i6WxAo+TtUgE20iVz5uYzGqHmxTNpq6FzIRb1uvHksbjFlin79Pkw
# eF0Dj80zxAY=
# =9JAI
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 01 Mar 2024 08:04:39 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-03-01' of https://gitlab.com/thuth/qemu:
chardev/char-socket: Fix TLS io channels sending too much data to the backend
tests/unit/test-util-sockets: Remove temporary file after test
hw/usb/bus.c: PCAP adding 0xA in Windows version
hw/intc/Kconfig: Fix GIC settings when using "--without-default-devices"
libqos/virtio.c: fix 'avail_event' offset in qvring_init()
libqos/virtio.c: init all elems in qvring_indirect_desc_setup()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
V2: fix build error on mipsel
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZeBrwAAKCRBAov/yOSY+
33YXA/4+A5Bpe/3+mSAWZSUlluGTqUi0ILBYRMyX1RXovMx4uCRGr7PXzAf03yKS
MZzlVzTuOK69WmTm/iTdYWOxkXisC3gzxL/wm8hP4lzh4c0dHrHRsKHqq6gR3+t2
ojdZn7TefeflnNqIhxXxgxb1OETofhBNnBJ74pvqxO7XV5SWnA==
=J2Kb
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20240229' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20240229
V2: fix build error on mipsel
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZeBrwAAKCRBAov/yOSY+
# 33YXA/4+A5Bpe/3+mSAWZSUlluGTqUi0ILBYRMyX1RXovMx4uCRGr7PXzAf03yKS
# MZzlVzTuOK69WmTm/iTdYWOxkXisC3gzxL/wm8hP4lzh4c0dHrHRsKHqq6gR3+t2
# ojdZn7TefeflnNqIhxXxgxb1OETofhBNnBJ74pvqxO7XV5SWnA==
# =J2Kb
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 29 Feb 2024 11:34:24 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20240229' of https://gitlab.com/gaosong/qemu:
loongarch: Change the UEFI loading mode to loongarch
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since Windows text files use CRLFs for all \n, the Windows version of QEMU
inserts a CR in the PCAP stream when a LF is encountered when using USB PCAP
files. This is due to the fact that the PCAP file is opened as TEXT instead
of BINARY.
To show an example, when using a very common protocol to USB disks, the BBB
protocol uses a 10-byte command packet. For example, the READ_CAPACITY(10)
command will have a command block length of 10 (0xA). When this 10-byte
command (part of the 31-byte CBW) is placed into the PCAP file, the Windows
file manager inserts a 0xD before the 0xA, turning the 31-byte CBW into a
32-byte CBW.
Actual CBW:
0040 55 53 42 43 01 00 00 00 08 00 00 00 80 00 0a 25 USBC...........%
0050 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...............
PCAP CBW
0040 55 53 42 43 01 00 00 00 08 00 00 00 80 00 0d 0a USBC............
0050 25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 %..............
I believe simply opening the PCAP file as BINARY instead of TEXT will fix
this issue.
Resolves: https://bugs.launchpad.net/qemu/+bug/2054889
Signed-off-by: Benjamin David Lunt <benlunt@fysnet.net>
Message-ID: <000101da6823$ce1bbf80$6a533e80$@fysnet.net>
[thuth: Break long line to avoid checkpatch.pl error]
Signed-off-by: Thomas Huth <thuth@redhat.com>
When using "--without-default-devices", the ARM_GICV3_TCG and ARM_GIC_KVM
settings currently get disabled, though the arm virt machine is only of
very limited use in that case. This also causes the migration-test to
fail in such builds. Let's make sure that we always keep the GIC switches
enabled in the --without-default-devices builds, too.
Message-ID: <20240221110059.152665-1-thuth@redhat.com>
Tested-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This removes a hidden use of qemu_host_page_size, hoisting
two uses of qemu_real_host_page_size to a local variable.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Helge Deller <deller@gmx.de>
The UEFI loading mode in loongarch is very different
from that in other architectures:loongarch's UEFI code
is in rom, while other architectures' UEFI code is in flash.
loongarch UEFI can be loaded as follows:
-machine virt,pflash=pflash0-format
-bios ./QEMU_EFI.fd
Other architectures load UEFI using the following methods:
-machine virt,pflash0=pflash0-format,pflash1=pflash1-format
loongarch's UEFI loading method makes qemu and libvirt incompatible
when using NVRAM, and the cost of loongarch's current loading method
far outweighs the benefits, so we decided to use the same UEFI loading
scheme as other architectures.
Cc: Andrea Bolognani <abologna@redhat.com>
Cc: maobibo@loongson.cn
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: Song Gao <gaosong@loongson.cn>
Cc: zhaotianrui@loongson.cn
Signed-off-by: Xianglai Li <lixianglai@loongson.cn>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <0bd892aa9b88e0f4cc904cb70efd0251fc1cde29.1708336919.git.lixianglai@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Mark Cave-Ayland