Since previous commit the MIPSITUState::cpu0 field is not
used anymore. Remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240209090513.9401-6-philmd@linaro.org>
Previous commit removed the MT*C0(SAAR) helpers which
were the only calls to itc_reconfigure() out of hw/,
we can reduce its scope and declare it statically.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240209090513.9401-3-philmd@linaro.org>
The MPS2 SCC device is broadly the same for all FPGA images, but has
minor differences in the behaviour of the CFG registers depending on
the image. In many cases we don't really care about the functionality
controlled by these registers and a reads-as-written or similar
behaviour is sufficient for the moment.
For the AN536 the required behaviour is:
* A_CFG0 has CPU reset and halt bits
- implement as reads-as-written for the moment
* A_CFG1 has flash or ATCM address 0 remap handling
- QEMU doesn't model this; implement as reads-as-written
* A_CFG2 has QSPI select (like AN524)
- implemented (no behaviour, as with AN524)
* A_CFG3 is MCC_MSB_ADDR "additional MCC addressing bits"
- QEMU doesn't care about these, so use the existing
RAZ behaviour for convenience
* A_CFG4 is board rev (like all other images)
- no change needed
* A_CFG5 is ACLK frq in hz (like AN524)
- implemented as reads-as-written, as for other boards
* A_CFG6 is core 0 vector table base address
- implemented as reads-as-written for the moment
* A_CFG7 is core 1 vector table base address
- implemented as reads-as-written for the moment
Make the changes necessary for this; leave TODO comments where
appropriate to indicate where we might want to come back and
implement things like CPU reset.
The other aspects of the device specific to this FPGA image (like the
values of the board ID and similar registers) will be set via the
device's qdev properties.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-8-peter.maydell@linaro.org
An access fault is raised when the Access Flag is not set in the
looked-up PTE and the AFFD field is not set in the corresponding context
descriptor. This was already implemented for stage 2. Implement it for
stage 1 as well.
Signed-off-by: Luc Michel <luc.michel@amd.com>
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Mostafa Saleh <smostafa@google.com>
Message-id: 20240213082211.3330400-1-luc.michel@amd.com
[PMM: tweaked comment text]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Armv8.1+ CPUs have the Virtual Host Extension (VHE) which adds a
non-secure EL2 virtual timer. We implemented the timer itself in the
CPU model, but never wired up its IRQ line to the GIC.
Wire up the IRQ line (this is always safe whether the CPU has the
interrupt or not, since it always creates the outbound IRQ line).
Report it to the guest via dtb and ACPI if the CPU has the feature.
The DTB binding is documented in the kernel's
Documentation/devicetree/bindings/timer/arm\,arch_timer.yaml
and the ACPI table entries are documented in the ACPI specification
version 6.3 or later.
Because the IRQ line ACPI binding is new in 6.3, we need to bump the
FADT table rev to show that we might be using 6.3 features.
Note that exposing this IRQ in the DTB will trigger a bug in EDK2
versions prior to edk2-stable202311, for users who use the virt board
with 'virtualization=on' to enable EL2 emulation and are booting an
EDK2 guest BIOS, if that EDK2 has assertions enabled. The effect is
that EDK2 will assert on bootup:
ASSERT [ArmTimerDxe] /home/kraxel/projects/qemu/roms/edk2/ArmVirtPkg/Library/ArmVirtTimerFdtClientLib/ArmVirtTimerFdtClientLib.c(72): PropSize == 36 || PropSize == 48
If you see that assertion you should do one of:
* update your EDK2 binaries to edk2-stable202311 or newer
* use the 'virt-8.2' versioned machine type
* not use 'virtualization=on'
(The versions shipped with QEMU itself have the fix.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Message-id: 20240122143537.233498-3-peter.maydell@linaro.org
vhost-user-snd support
x2APIC mode with TCG support
CXL update to r3.1
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXMoXUPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpFtMIAKUKD0hzJrwOyPo4xsRUMbsB3ehIsJsMKfOK
w+JWzTaojAG8ENPelWBdL2sEIs5U73VOchjLqHbH2m5sz6GJ13214amvdU/fYc8+
/dU2ZKoAmaR5L1ovKO/fq07y/J6DrITZ5tosy2i84Xa8EnsL4j3wEPNVWsDi7dna
mvXUICSOOoJQ4O2YhSruKCQ8qIgF1/0Oi3u/rcrW3alSs8VQlrtQXxl6k+LbYqek
+Fytco3jMRHPvQ+GYUIwGuHjN15ghArcvbsV0GIa+24BPY5h7YbDYGbfasePT5OK
zDz51jitkoyDrQr+OzwOEe/X5+dVGhayRXfMtU5Qm53IE3y61qc=
=K4b1
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
vhost-user-snd support
x2APIC mode with TCG support
CXL update to r3.1
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXMoXUPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpFtMIAKUKD0hzJrwOyPo4xsRUMbsB3ehIsJsMKfOK
# w+JWzTaojAG8ENPelWBdL2sEIs5U73VOchjLqHbH2m5sz6GJ13214amvdU/fYc8+
# /dU2ZKoAmaR5L1ovKO/fq07y/J6DrITZ5tosy2i84Xa8EnsL4j3wEPNVWsDi7dna
# mvXUICSOOoJQ4O2YhSruKCQ8qIgF1/0Oi3u/rcrW3alSs8VQlrtQXxl6k+LbYqek
# +Fytco3jMRHPvQ+GYUIwGuHjN15ghArcvbsV0GIa+24BPY5h7YbDYGbfasePT5OK
# zDz51jitkoyDrQr+OzwOEe/X5+dVGhayRXfMtU5Qm53IE3y61qc=
# =K4b1
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 14 Feb 2024 11:18:13 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (60 commits)
MAINTAINERS: Switch to my Enfabrica email
virtio-gpu-rutabaga.c: override resource_destroy method
virtio-gpu.c: add resource_destroy class method
hw/display/virtio-gpu.c: use reset_bh class method
hw/smbios: Fix port connector option validation
hw/smbios: Fix OEM strings table option validation
virtio-gpu: Correct virgl_renderer_resource_get_info() error check
hw/cxl: Standardize all references on CXL r3.1 and minor updates
hw/cxl: Update mailbox status registers.
hw/cxl: Update RAS Capability Definitions for version 3.
hw/cxl: Update link register definitions.
hw/cxl: Update HDM Decoder capability to version 3
tests/acpi: Update DSDT.cxl to reflect change _STA return value.
hw/i386: Fix _STA return value for ACPI0017
tests/acpi: Allow update of DSDT.cxl
hw/mem/cxl_type3: Fix potential divide by zero reported by coverity
hw/cxl: Pass NULL for a NULL MemoryRegionOps
hw/cxl: Pass CXLComponentState to cache_mem_ops
hw/cxl/device: read from register values in mdev_reg_read()
hw/cxl/mbox: Remove dead code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When destroying/unrefing resources, devices such as virtio-gpu-rutabaga
need to do their own bookkeeping (free rutabaga resources that are
associated with the virtio_gpu_simple_resource).
This commit adds a class method so that virtio-gpu-rutabaga can override
it in the next commit.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <b0a86630c4d601f3a269fd7e08cfefc13bd4e219.1706626470.git.manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previously not all references mentioned any spec version at all.
Given r3.1 is the current specification available for evaluation at
www.computeexpresslink.org update references to refer to that.
Hopefully this won't become a never ending job.
A few structure definitions have been updated to add new fields.
Defaults of 0 and read only are valid choices for these new DVSEC
registers so go with that for now.
There are additional error codes and some of the 'questions' in
the comments are resolved now.
Update documentation reference to point to the CXL r3.1 specification
with naming closer to what is on the cover.
For cases where there are structure version numbers, add defines
so they can be found next to the register definitions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst the reported version was 1 so there should be no changes,
a couple of fields (where the value 0 was valid) were not
defined. Make those explicit and update references to be based
on CXL r3.1.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Part of bringing all of CXL emulation inline with CXL r3.1.
No functional changes.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Not actually implemented, but we need to reserve more space for
the larger version of the structure in CXL r3.1.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Part of standardizing the QEMU code on CXL r3.1.
No fuctional changes as everything added is optional and
it is set as not implemented.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the current mdev_reg_read() implementation, it consistently returns
that the Media Status is Ready (01b). This was fine until commit
25a52959f9 ("hw/cxl: Add support for device sanitation") because the
media was presumed to be ready.
However, as per the CXL 3.0 spec "8.2.9.8.5.1 Sanitize (Opcode 4400h)",
during sanitation, the Media State should be set to Disabled (11b). The
mentioned commit correctly sets it to Disabled, but mdev_reg_read()
still returns Media Status as Ready.
To address this, update mdev_reg_read() to read register values instead
of returning dummy values.
Note that __toggle_media() managed to not only write something
that no one read, it did it to the wrong register storage and
so changed the reported mailbox size which was definitely not
the intent. That gets fixed as a side effect of allocating
separate state storage for this register.
Fixes: commit 25a52959f9 ("hw/cxl: Add support for device sanitation")
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The real SuperI/O chips emulated by QEMU allow for relocating and enabling or
disabling their SuperI/O functions via software. So far this is not implemented.
Prepare for that by adding isa_parallel_set_{enabled,iobase}.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-10-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The real SuperI/O chips emulated by QEMU allow for relocating and enabling or
disabling their SuperI/O functions via software. So far this is not implemented.
Prepare for that by adding isa_serial_set_{enabled,iobase}.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-9-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The real SuperI/O chips emulated by QEMU allow for relocating and enabling or
disabling their SuperI/O functions via software. So far this is not implemented.
Prepare for that by adding isa_fdc_set_{enabled,iobase}.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ParallelState::portio_list isn't used inside ParallelState context but only
inside ISAParallelState context, so move it there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU populates the apic_state attribute of x86 CPUs if supported by real
hardware or if SMP is active. When handling interrupts, it just checks whether
apic_state is populated to route the interrupt to the PIC or to the APIC.
However, chapter 10.4.3 of [1] requires that:
When IA32_APIC_BASE[11] is 0, the processor is functionally equivalent to an
IA-32 processor without an on-chip APIC.
This means that when apic_state is populated, QEMU needs to check for the
MSR_IA32_APICBASE_ENABLE flag in addition. Implement this which fixes some
real-world BIOSes.
[1] Intel 64 and IA-32 Architectures Software Developer's Manual, Vol. 3A:
System Programming Guide, Part 1
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240106132546.21248-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit adds support for x2APIC transitions when writing to
MSR_IA32_APICBASE register and finally adds CPUID_EXT_X2APIC to
TCG_EXT_FEATURES.
The set_base in APICCommonClass now returns an integer to indicate error in
execution. apic_set_base return -1 on invalid APIC state transition,
accelerator can use this to raise appropriate exception.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-4-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit extends the APIC ID to 32-bit long and remove the 255 max APIC
ID limit in userspace APIC. The array that manages local APICs is now
dynamically allocated based on the max APIC ID of created x86 machine.
Also, new x2APIC IPI destination determination scheme, self IPI and x2APIC
mode register access are supported.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-3-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit creates apic_register_read/write which are used by both
apic_mem_read/write for MMIO access and apic_msr_read/write for MSR access.
The apic_msr_read/write returns -1 on error, accelerator can use this to
raise the appropriate exception.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-2-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch derives vhost-user-input from vhost-user-base class, so make
the input stub as a simpler boilerplate wrapper.
With the refactoring, vhost-user-input adds the property 'chardev', this
leads to conflict with the vhost-user-input-pci adds the same property.
To resolve the error, remove the duplicate property from
vhost-user-input-pci.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20231120043721.50555-5-leo.yan@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-12-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we can take advantage of the new base class and make
vhost-user-i2c a much simpler boilerplate wrapper. Also as this
doesn't require any target specific hacks we only need to build the
stubs once.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-6-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now the new base class supports config handling we can take advantage
and make vhost-user-gpio a much simpler boilerplate wrapper. Also as
this doesn't require any target specific hacks we only need to build
the stubs once.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-5-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we can take advantage of our new base class and make
vhost-user-rng a much simpler boilerplate wrapper. Also as this
doesn't require any target specific hacks we only need to build the
stubs once.
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-4-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Lets keep a cleaner split between the base class and the derived
vhost-user-device which we can use for generic vhost-user stubs. This
includes an update to introduce the vq_size property so the number of
entries in a virtq can be defined.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-2-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the DRQ IRQ is updated every time DMA data is sent/received which
is both inefficient and causes excessive logging of the DRQ state. Add a
new drq_state bool that only updates the DRQ IRQ if its state changes.
This commit adds the new drq_state bool to the migration state: since the
version number has already been increased earlier in the series, there is
no need to repeat it again here. The DRQ IRQ is (currently) only used for
PDMA transfers which already have a migration break in this series so
there are no problems setting its value post-load.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-87-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The IRQ represented by irq_data is actually the DRQ (DMA request) line so rename
it accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-86-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
According to the datasheet the previous ESP command remains in the ESP_CMD
register, which caused a problem when consecutive TI commands were issued as
it becomes impossible for the state machine to know when the first TI
command finishes.
This was the original reason for introducing the ti_cmd field which kept
track of the last written command for this purpose. However closer reading
of the datasheet shows that a TI command that terminates due to a change of
SCSI target phase resets the ESP_CMD register to zero which solves this
problem.
Now that this has been fixed in the previous commit, remove the unneeded
ti_cmd field and access the ESP_CMD register directly instead. Bump the
vmstate_esp version to indicate that the ti_cmd field is no longer included.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-64-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This field is currently used to handle deferred interrupts for the DATA IN phase
but the code will soon be updated to do the same for the DATA OUT phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-58-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Note that this is a migration break for the q800 machine because the extra PDMA
information is no longer included.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-57-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The special logic in write_response_pdma_cb() is now no longer required since
esp_do_dma() can be used as a direct replacement.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-55-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The special logic in satn_stop_pdma_cb() is now no longer required since
esp_do_dma() can be used as a direct replacement.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-53-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The special logic in satn_pdma_cb() is now no longer required since esp_do_dma()
can be used as a direct replacement.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-50-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This can now be handled by the existing do_dma_pdma_cb() function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-37-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Some enhancements and fixes for the hppa target.
The major change is, that this patchset adds a new SeaBIOS-hppa firmware
which is built as 32- and 64-bit firmware.
The new 64-bit firmware is necessary to fully support 64-bit operating systems
(HP-UX, Linux, NetBSD,...).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZcquAQAKCRD3ErUQojoP
X9pjAQCVsWyuYlGCW2paIGVWKV0vsOpwetUrbhRtFUZGqZxb4AD9FbMsXRcCN/oq
CotBPY/a8MEzIQcwYl5QbcI5nNW4ygs=
=RA0B
-----END PGP SIGNATURE-----
Merge tag 'hppa64-pull-request' of https://github.com/hdeller/qemu-hppa into staging
target/hppa: Enhancements and fixes
Some enhancements and fixes for the hppa target.
The major change is, that this patchset adds a new SeaBIOS-hppa firmware
which is built as 32- and 64-bit firmware.
The new 64-bit firmware is necessary to fully support 64-bit operating systems
(HP-UX, Linux, NetBSD,...).
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZcquAQAKCRD3ErUQojoP
# X9pjAQCVsWyuYlGCW2paIGVWKV0vsOpwetUrbhRtFUZGqZxb4AD9FbMsXRcCN/oq
# CotBPY/a8MEzIQcwYl5QbcI5nNW4ygs=
# =RA0B
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 12 Feb 2024 23:47:13 GMT
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* tag 'hppa64-pull-request' of https://github.com/hdeller/qemu-hppa:
hw/hppa/machine: Load 64-bit firmware on 64-bit machines
target/hppa: Update SeaBIOS-hppa to version 16
hw/net/tulip: add chip status register values
target/hppa: PDC_BTLB_INFO uses 32-bit ints
target/hppa: Allow read-access to PSW with rsm 0,reg instruction
lasi: Add reset I/O ports for LASI audio and FDC
target/hppa: Implement do_transaction_failed handler for I/O errors
lasi: allow access to LAN MAC address registers
hw/pci-host/astro: Implement Hard Fail and Soft Fail mode
hw/pci-host/astro: Avoid aborting on access failure
target/hppa: Add "diag 0x101" for console output support
disas/hppa: Add disassembly for qemu specific instructions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SocketAddress branch @fd is documented in enum SocketAddressType,
unlike the other branches. That's because the branch's type is String
from common.json.
Use a local copy of String, so we can put the documentation in the
usual place.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240205074709.3613229-14-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Linux writes zeroes at bootup into the default ports for LASI audio and
LASI floppy controller to reset those devices. Allow writing to those
registers to avoid HPMCs.
Signed-off-by: Helge Deller <deller@gmx.de>
The Astro/Elroy chip can work in either Hard-Fail or Soft-Fail mode.
Hard fail means the system bus will send an HPMC (=crash) to the
processor, soft fail means the system bus will ignore timeouts of
MMIO-reads or MMIO-writes and return -1ULL.
The HF mode is controlled by a bit in the status register and is usually
programmed by the OS. Return the corresponing values based on the current
value of that bit.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This regressed qemu-system-xtensa:
TEST test_load_store on xtensa
qemu-system-xtensa: Some ROM regions are overlapping
These ROM regions might have been loaded by direct user request or by default.
They could be BIOS/firmware images, a guest kernel, initrd or some other file loaded into guest memory.
Check whether you intended to load all this guest code, and whether it has been built to load to the correct addresses.
The following two regions overlap (in the memory address space):
test_load_store ELF program header segment 1 (addresses 0x0000000000001000 - 0x0000000000001f26)
test_load_store ELF program header segment 2 (addresses 0x0000000000001ab8 - 0x0000000000001ab8)
make[1]: *** [Makefile:187: run-test_load_store] Error 1
This reverts commit 62570f1434.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240207163812.3231697-5-alex.bennee@linaro.org>
* Check for 'A' extension on all atomic instructions
* Add support for 'B' extension
* Internally deprecate riscv_cpu_options
* Implement optional CSR mcontext of debug Sdtrig extension
* Internally add cpu->cfg.vlenb and remove cpu->cfg.vlen
* Support vlenb and vregs[] in KVM
* RISC-V gdbstub and TCG plugin improvements
* Remove vxrm and vxsat from FCSR
* Use RISCVException as return type for all csr ops
* Use g_autofree more and fix a memory leak
* Add support for Zaamo and Zalrsc
* Support new isa extension detection devicetree properties
* SMBIOS support for RISC-V virt machine
* Enable xtheadsync under user mode
* Add rv32i,rv32e and rv64e CPUs
-----BEGIN PGP SIGNATURE-----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=yuRM
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20240209' of https://github.com/alistair23/qemu into staging
RISC-V PR for 9.0
* Check for 'A' extension on all atomic instructions
* Add support for 'B' extension
* Internally deprecate riscv_cpu_options
* Implement optional CSR mcontext of debug Sdtrig extension
* Internally add cpu->cfg.vlenb and remove cpu->cfg.vlen
* Support vlenb and vregs[] in KVM
* RISC-V gdbstub and TCG plugin improvements
* Remove vxrm and vxsat from FCSR
* Use RISCVException as return type for all csr ops
* Use g_autofree more and fix a memory leak
* Add support for Zaamo and Zalrsc
* Support new isa extension detection devicetree properties
* SMBIOS support for RISC-V virt machine
* Enable xtheadsync under user mode
* Add rv32i,rv32e and rv64e CPUs
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmXGBRAACgkQr3yVEwxT
# gBPqVA//etMiwP8+lQb2E4pw+QwBIzpm3qFyBlqgSCFrekj1u2kYNd4CH3CKurWE
# ysoQ6OAMeb0MUbRHdjrejjzD/wOg7JNA9h7ynM1VbupveBrJY3GWC6qQWSG+A1j/
# LSgmr/dDya74chDxjxa+7ld3xqloHi5OtdGaeORfdPXl7mjCCKKCoSKYCex1ykup
# uuB7bsjeWeWEbuUsntmeuHJLZJuhpnbuZJmp17tEo+3vWXqjxV00Lik+XMwh3gua
# KOLiAqHjGr2NEhA3Mg1JLcQ+6JLTDM9ugZpQeNGQwMkfuB/RAU7jO/1Di3flbadF
# 8l2xOHu3mydDbfdxTGZNJjcIrMTX/YEewAYZLRYpNsyPOMntgq8HEegwCdWGvK7C
# M5Tc59MNSuBt+zkZkHd21qLYusa2ThP4YT/schh7IA+2F1TSKdhlptEzi2oebIc7
# ilLSgZ9Of72QlAH2OPJNSAL9Nbc06MHEM0JiHIJa5u+XdcVRhZus5h1YIOKXisqF
# YPP22RnI5Jj5d5csa/0ONAZGFh5SRMTJtpjKoKSkzoYJWDjCQ2MiUAOmLscchMZd
# wbK0vjeRf6kRG4U4z7nTmHS9kzH8RXUZDecVcOITuMpKih9LhUiCZ+xPunFYPycJ
# WNFa9/pENcCXJweXvtk4NHwx933rX56678lF6KY2hwUwwaiBOv4=
# =yuRM
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 09 Feb 2024 10:57:20 GMT
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20240209' of https://github.com/alistair23/qemu: (61 commits)
target/riscv: add rv32i, rv32e and rv64e CPUs
target/riscv/cpu.c: add riscv_bare_cpu_init()
target/riscv: Enable xtheadsync under user mode
qemu-options: enable -smbios option on RISC-V
target/riscv: SMBIOS support for RISC-V virt machine
smbios: function to set default processor family
smbios: add processor-family option
target/riscv: support new isa extension detection devicetree properties
target/riscv: use misa_mxl_max to populate isa string rather than TARGET_LONG_BITS
target/riscv: Expose Zaamo and Zalrsc extensions
target/riscv: Check 'A' and split extensions for atomic instructions
target/riscv: Add Zaamo and Zalrsc extension infrastructure
hw/riscv/virt.c: use g_autofree in create_fdt_*
hw/riscv/virt.c: use g_autofree in virt_machine_init()
hw/riscv/virt.c: use g_autofree in create_fdt_virtio()
hw/riscv/virt.c: use g_autofree in create_fdt_sockets()
hw/riscv/virt.c: use g_autofree in create_fdt_socket_cpus()
hw/riscv/numa.c: use g_autofree in socket_fdt_write_distance_matrix()
hw/riscv/virt-acpi-build.c: fix leak in build_rhct()
target/riscv: Use RISCVException as return type for all csr ops
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a function to set the default processor family.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240123184229.10415-3-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
usb-storage is for the most part just a wrapper around an internally
created scsi-disk device. It uses DEFINE_BLOCK_PROPERTIES() to offer all
of the usual block device properties to the user, but then only forwards
a few select properties to the internal device while the rest is
silently ignored.
This changes scsi_bus_legacy_add_drive() to accept a whole BlockConf
instead of some individual values inside of it so that usb-storage can
now pass the whole configuration to the internal scsi-disk. This enables
the remaining block device properties, e.g. logical/physical_block_size
or discard_granularity.
Buglink: https://issues.redhat.com/browse/RHEL-22375
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240131130607.24117-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The VirtIOBlock::rq field has had the type void * since its introduction
in commit 869a5c6df1 ("Stop VM on error in virtio-blk. (Gleb
Natapov)").
Perhaps this was done to avoid the forward declaration of
VirtIOBlockReq.
Hanna Czenczek <hreitz@redhat.com> pointed out the missing type. Specify
the actual type because there is no need to use void * here.
Suggested-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240206190610.107963-5-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
QEMU initializes preallocated backend memory as the objects are parsed from
the command line. This is not optimal in some cases (e.g. memory spanning
multiple NUMA nodes) because the memory objects are initialized in series.
Allow the initialization to occur in parallel (asynchronously). In order to
ensure optimal thread placement, asynchronous initialization requires prealloc
context threads to be in use.
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Message-ID: <20240131165327.3154970-2-mark.kanda@oracle.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
To be used after all targets have populated the hook.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This function is no longer used, as all its callers have been converted
to use pci_init_nic_devices() instead.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Create the device only if there is a corresponding NIC config for it.
Remove the explicit check on nd_table[0].used from hw/hppa/machine.c
which (since commit d8a3220005) tries to do the same thing.
The lasi_82596 support has been disabled since it was first introduced,
since enable_lasi_lan() has always been zero. This allows the user to
enable it by explicitly requesting a NIC model 'lasi_82596' or just
using the alias 'lasi'. Otherwise, it defaults to a PCI NIC as before.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preseve the existing behaviour for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Some callers instantiate the device unconditionally, others will do so only
if there is a NICInfo to go with it. This appears to be fairly random, but
preserve the existing behaviour of each caller for now.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
When instantiating XenBus itself, for each NIC which is configured with
either the model unspecified, or set to to "xen" or "xen-net-device",
create a corresponding xen-net-device for it.
Now we can revert the previous more hackish version which relied on the
platform code explicitly registering the NICs on its own XenBus, having
returned the BusState* from xen_bus_init() itself.
This also fixes the setup for Xen PV guests, which was previously broken
in various ways and never actually managed to peer with the netdev.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Eliminate direct access to nd_table[] and nb_nics by processing the the
Xen and ISA NICs first and then calling pci_init_nic_devices() for the
rest.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The loop over nd_table[] to add PCI NICs is repeated in quite a few
places. Add a helper function to do it.
Some platforms also try to instantiate a specific model in a specific
slot, to match the real hardware. Add pci_init_nic_in_slot() for that
purpose.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
This patch will allow the SPI controller to be accessible from BCM2835 based
boards as SPI0. SPI driver is usually disabled by default and config.txt does
not work.
Instead, dtmerge can be used to apply spi=on on a bcm2835 dtb file.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-3-rayhan.faizel@gmail.com
[PMM: indent tweak]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the SPI controller for the BCM2835. Polling and interrupt modes
of transfer are supported. DMA and LoSSI modes are currently unimplemented.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-2-rayhan.faizel@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the basic registers of GMAC device and sets
registers for networking functionalities.
Squashed IRQ Implementation patch into this one for compliation.
Tested:
The following message shows up with the change:
Broadcom BCM54612E stmmac-0:00: attached PHY driver [Broadcom BCM54612E] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
stmmaceth f0802000.eth eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Change-Id: If71c6d486b95edcccba109ba454870714d7e0940
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Nabih Estefan Diaz <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-2-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M2Sxxx SoC family can only be used with Cortex-M3.
Propagating the CPU type from the board level is pointless.
Hard-code the CPU type at the SoC level.
Remove the now ignored MachineClass::default_cpu_type field.
Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-6-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
BusClass currently has transitional infrastructure to support
subclasses which implement the legacy BusClass::reset method rather
than the Resettable interface. We have now removed all the users of
BusClass::reset in the tree, so we can remove the transitional
infrastructure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-6-peter.maydell@linaro.org
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
-----BEGIN PGP SIGNATURE-----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=0C5S
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu into staging
aspeed queue:
* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
controller bridge
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmW7Sa8ACgkQUaNDx8/7
# 7KG7mw/8DbMJY6aqgq5YANszzem1ktJphPCNxq081cbczCOUpCNX4aL+0/ANvxxD
# lbJQB+SZeIRmuFbxYPhq68rtzB4vG7tsQpns4H33EPKT4vuzF70lq4fgptMiun3q
# 1ZJ2LF3jonvQWdhbC17wzAQz0FFb4F7XOxz++UL4okPsgzsYItnd+TWs8q7+erRb
# 84UwN+eBTBAl/FiNk679/tBTqAfCVGgQ7dzotr4f3tg5POvrGOrlEjAn0O+dGGDj
# wgILmpEBsTsilRB1tz8Kw0j/v/VkHz1DJu45lRAV9CIrN22iKcjMilNGgNDT8kcI
# yAlxAw3iN+hVFqDov8wFPjDYd/Qw2oRAPy2Kd14hW9xL8zBOTms1JK5L0PS2+Feo
# ZjMJ2cOJq3t4Wt1ZXRhgHfF4ANwP0OZ/y9bHCy3CkBljEeiTQbikHP9gVV4qHXZH
# 4Q0HnDZQwAgobw3CmZ8jVx1dQueqy3ycuvkhCyv3S0l/tdbtXDtr5pNNu3dAP/PJ
# 3nifLdRImhDvxxO9GKaCdUVLzELzMJl0GrgAsVJPKVnKHA4IiVKmB+XcW9IUbfy/
# 3zA2wHJLrEF+MF6MsuNcEYCCqUvyNLm7rUrXk1wNLXpCJ35bbW5IYy7Ty/8E2GHb
# D5Cv/EPNhMBiNA4+HqQlMOTC13Ozv2qwCuWYCh2Ik8mnzaEiyTo=
# =0C5S
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Feb 2024 07:35:11 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu:
hw/fsi: Update MAINTAINER list
hw/fsi: Added FSI documentation
hw/fsi: Added qtest
hw/arm: Hook up FSI module in AST2600
hw/fsi: Aspeed APB2OPB & On-chip peripheral bus
hw/fsi: Introduce IBM's FSI master
hw/fsi: Introduce IBM's cfam
hw/fsi: Introduce IBM's fsi-slave model
hw/fsi: Introduce IBM's FSI Bus
hw/fsi: Introduce IBM's scratchpad device
hw/fsi: Introduce IBM's Local bus
hw/arm/aspeed: Check for CPU types in machine_run_board_init()
hw/arm/aspeed: Introduce aspeed_soc_cpu_type() helper
hw/arm/aspeed: Init CPU defaults in a common helper
hw/arm/aspeed: Set default CPU count using aspeed_soc_num_cpus()
hw/arm/aspeed: Remove dead code
tests/avocado/machine_aspeed.py: Update buildroot images to 2023.11
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service
processor access to the internal buses of a host POWER processor to
perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage,
including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of
interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on buses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: fsi.lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
The LBUS is modelled to maintain the qdev bus hierarchy and to take
advantage of the object model to automatically generate the CFAM
configuration block. The configuration block presents engines in the
order they are attached to the CFAM's LBUS. Engine implementations
should subclass the LBusDevice and set the 'config' member of
LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for
a CFAM to be simultaneously driven from multiple FSI links. The modeling
is not so complete; it's assumed that each CFAM is attached to a single
FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This
is not necessary to get FSI off the ground thanks to the mapping of the
CFAM address space onto the OPB address space - the models follow this
directly and map the CFAM memory region into the OPB's memory region.
Future work includes supporting more advanced accesses that drive the
FSI master directly rather than indirectly via the CFAM mapping, which
will require implementing the FSI state machine and methods for each of
the FSI symbols on the slave. Further down the track we can also look at
supporting the bitbanged SoftFSI drivers in Linux by extending the FSI
slave model to resolve sequences of GPIO IRQs into FSI symbols, and
calling the associated symbol method on the slave to map the access onto
the CFAM.
Testing:
Tested by reading cfam config address 0 on rainier machine type.
root@p10bmc:~# pdbg -a getcfam 0x0
p0: 0x0 = 0xc0022d15
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved FSIMasterState under AspeedAPB2OPBState
- modified fsi_opb_fsi_master_address() and
fsi_opb_opb2fsi_address()
- instroduced fsi_aspeed_apb2opb_init()
- reworked fsi_aspeed_apb2opb_realize()
- removed FSIMasterState object and fsi_opb_realize()
- simplified OPBus
- introduced fsi_aspeed_apb2opb_rw to fix endianness issue ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
This commit models the FSI master. CFAM is hanging out of FSI master which is a bus controller.
The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - move FSICFAMState object under FSIMasterState
- introduced fsi_master_init()
- reworked fsi_master_realize()
- dropped FSIBus definition ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on busses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c
- introduced fsi_cfam_instance_init()
- reworked fsi_cfam_realize() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where FSI bus is introduced.
The FSI bus is a simple bus where FSI master is attached.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed include/hw/fsi/engine-scratchpad.h and
hw/fsi/engine-scratchpad.c
- dropped FSI_SCRATCHPAD
- included FSIBus definition
- dropped hw/fsi/trace-events changes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The scratchpad provides a set of non-functional registers. The firmware
is free to use them, hardware does not support any special management
support. The scratchpad registers can be read or written from LBUS
slave. The scratch pad is managed under FSI CFAM state.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
- moved FSIScratchPad code under cfam.c ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a part of patchset where IBM's Flexible Service Interface is
introduced.
The LBUS is modelled to maintain mapped memory for the devices. The
memory is mapped after CFAM config, peek table and FSI slave registers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed lbus_add_device() bc unused
- removed lbus_create_device() bc used only once
- removed "address" property
- updated meson.build to build fsi dir
- included an empty hw/fsi/trace-events ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Aspeed SoCs use a single CPU type (set as AspeedSoCClass::cpu_type).
Convert it to a NULL-terminated array (of a single non-NULL element).
Set MachineClass::valid_cpu_types[] to use the common machine code
to provide hints when the requested CPU is invalid (see commit
e702cbc19e ("machine: Improve is_cpu_type_supported()").
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to alter AspeedSoCClass::cpu_type in the next
commit, introduce the aspeed_soc_cpu_type() helper to
retrieve the per-SoC CPU type from AspeedSoCClass.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAmW6NScPHG1qdEB0bHMu
bXNrLnJ1AAoJEHAbT2saaT5ZdQYH/2fhfhZotH0V2qAcMxlOoHbAE9UhZNRsSYtf
QFP0GXFYFAMm7LHkPUbvKgO7LylKWAOMn/zKZqgj1Vf1EpoKQ2FwLtR/buDz86Ec
pi2OrDPRA7Ay5c3ow3YZZkUOhQTTcR5rNjYctPtt/J4j8ol/z5vre7weJIg2bCJe
zI7vIVg7iFFzbkXY20KHngJ5nDC+aEm7WaGlxAP8kfkvy324Wy9O2k8qu2J5zbLT
HGvh3rwEDvRTYe4CaKFFHWNV0m4092HAr/dJBobugI5VZ6QQpK6Tgy8N+4ZrCHD2
SjUKeym85VTOYGuY8b18fk5MQK2SzsfBUJ4x8VGC75W4mJ8agdc=
=HImO
-----END PGP SIGNATURE-----
Merge tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu into staging
trivial patches for 2024-01-31
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAmW6NScPHG1qdEB0bHMu
# bXNrLnJ1AAoJEHAbT2saaT5ZdQYH/2fhfhZotH0V2qAcMxlOoHbAE9UhZNRsSYtf
# QFP0GXFYFAMm7LHkPUbvKgO7LylKWAOMn/zKZqgj1Vf1EpoKQ2FwLtR/buDz86Ec
# pi2OrDPRA7Ay5c3ow3YZZkUOhQTTcR5rNjYctPtt/J4j8ol/z5vre7weJIg2bCJe
# zI7vIVg7iFFzbkXY20KHngJ5nDC+aEm7WaGlxAP8kfkvy324Wy9O2k8qu2J5zbLT
# HGvh3rwEDvRTYe4CaKFFHWNV0m4092HAr/dJBobugI5VZ6QQpK6Tgy8N+4ZrCHD2
# SjUKeym85VTOYGuY8b18fk5MQK2SzsfBUJ4x8VGC75W4mJ8agdc=
# =HImO
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 31 Jan 2024 11:55:19 GMT
# gpg: using RSA key 7B73BAD68BE7A2C289314B22701B4F6B1A693E59
# gpg: issuer "mjt@tls.msk.ru"
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>" [full]
# gpg: aka "Michael Tokarev <mjt@corpit.ru>" [full]
# gpg: aka "Michael Tokarev <mjt@debian.org>" [full]
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D 4324 457C E0A0 8044 65C5
# Subkey fingerprint: 7B73 BAD6 8BE7 A2C2 8931 4B22 701B 4F6B 1A69 3E59
* tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu: (21 commits)
hw/hyperv: Include missing headers
hw/intc/xics: Include missing 'cpu.h' header
hw/arm: Add `\n` to hint message
hw/loongarch: Add `\n` to hint message
hw/i386: Add `\n` to hint message
backends/hostmem: Fix block comments style (checkpatch.pl warnings)
misc: Clean up includes
riscv: Clean up includes
cxl: Clean up includes
include: Clean up includes
m68k: Clean up includes
acpi: Clean up includes
aspeed: Clean up includes
disas/riscv: Clean up includes
hyperv: Clean up includes
scripts/clean-includes: Update exclude list
mailmap: Fix Stefan Weil email
qemu-docs: Update options for graphical frontends
qapi/migration.json: Fix the member name for MigrationCapability
colo: examples: remove mentions of script= and (wrong) downscript=
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In cases where a device tries to read more bytes than the block device
contains, the error is vague: "device requires X bytes, block backend
provides Y bytes".
This patch changes the errors of this function to include the block
backend name, the device id and device type name where appropriate.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 7260eadff22c08457740117c1bb7bd2b4353acb9.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a simple method to return some kind of human readable identifier for
use in error messages.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 8b566bfced98ae44be1fcc1f8e7215f0c3393aa1.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This commit was created with scripts/clean-includes:
./scripts/clean-includes --git include include/*/*.h include/*/*/*.h
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes:
./scripts/clean-includes --git m68k include/hw/audio/asc.h include/hw/m68k/*.h
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This commit was created with scripts/clean-includes:
./scripts/clean-includes --git acpi include/hw/*/*acpi.h hw/*/*acpi.c
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In order to make accel/tcg/ target agnostic,
introduce the cpu_exec_halt() handler.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240124101639.30056-9-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In order to make accel/tcg/ target agnostic,
introduce the need_replay_interrupt() handler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Message-Id: <20240124101639.30056-7-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
QEMU coding style recommends using structure typedefs.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Always include fake_user_interrupt in user-only build, despite
only being used for i386. This will enable cpu-exec.c to be
compiled only once.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Message-ID: <20240119144024.14289-18-anjo@rev.ng>
[rth: Split out of a larger patch; remove TARGET_I386 conditional.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The ifdef out of which it is moved is not quite right: do_interrupt is
only needed for system mode. Move it to the top of a different ifdef
block, which preserves its position within the structure for that case.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20240119144024.14289-18-anjo@rev.ng>
[rth: Split from a larger patch and simplified.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
cpu-common.h is only needed for vaddr
Signed-off-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20240119144024.14289-8-anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch implements a 32 half word FIFO as per imx serial device
specifications. If a non empty FIFO is below the trigger level, an
ageing timer will tick for a duration of 8 characters. On expiry,
AGTIM will be set triggering an interrupt. AGTIM timer resets when
there is activity in the receive FIFO.
Otherwise, RRDY is set when trigger level is exceeded. The receive
trigger level is 8 in newer kernel versions and 1 in older ones.
This change will break migration compatibility for the imx boards.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240125151931.83494-1-rayhan.faizel@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: commit message tidyups]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add MMDC, OCOTP, SQPI, CAAM, and USBMISC as unimplemented devices.
This allows operating systems such as Linux to run emulations such as
mcimx6ul-evk.
Before commit 0cd4926b85 ("Refactor i.MX6UL processor code"), the affected
memory ranges were covered by the unimplemented DAP device. The commit
reduced the DAP address range from 0x100000 to 4kB, and the emulation
thus no longer covered the various unimplemented devices in the affected
address range.
Fixes: 0cd4926b85 ("Refactor i.MX6UL processor code")
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240120005356.2599547-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now than we can access the M-profile bank index
definitions from the target-agnostic "cpu-qom.h"
header, we don't need the huge "cpu.h" anymore
(except in hw/arm/armv7m.c). Reduce its inclusion
to the source unit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-17-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"target/arm/cpu.h" is target specific, any file including it
becomes target specific too, thus this is the same for any file
including "hw/misc/xlnx-versal-crl.h".
"hw/misc/xlnx-versal-crl.h" doesn't require any target specific
definition however, only the target-agnostic QOM definitions
from "target/arm/cpu-qom.h". Include the latter header to avoid
tainting unnecessary objects as target-specific.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-14-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
include/hw/arm/xlnx-versal.h uses the ARMCPU structure which
is defined in the "target/arm/cpu.h" header. Include it in
order to avoid when refactoring unrelated headers:
In file included from hw/arm/xlnx-versal-virt.c:20:
include/hw/arm/xlnx-versal.h:62:23: error: array has incomplete element type 'ARMCPU' (aka 'struct ArchCPU')
ARMCPU cpu[XLNX_VERSAL_NR_ACPUS];
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240118200643.29037-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add watchdog timer support to Allwinner-H40 and Bananapi.
The watchdog timer is added as an overlay to the Timer
module memory map.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Message-id: 20240115182757.1095012-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports an AHCI compliant SATA controller.
Add support for it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240115182757.1095012-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports two USB host ports shared between a USB 2.0 EHCI
host controller and a USB 1.1 OHCI host controller. Add support for both
of them.
If machine USB support is not enabled, create unimplemented devices
for the USB memory ranges to avoid crashes when booting Linux.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240115182757.1095012-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The dataplane code is really about using ioeventfd. It's used both for
IOThreads (what we think of as dataplane) and for the core virtio-pci
code's ioeventfd feature (which is enabled by default and used when no
IOThread has been specified). Rename the code to reflect this.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-4-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The dataplane code used to be significantly different from the
non-dataplane code and therefore had a separate source file.
Over time the difference has gotten smaller because the I/O code paths
were unified. Nowadays the distinction between the VirtIOBlock and
VirtIOBlockDataPlane structs is more of an inconvenience that hinders
code simplification.
Move hw/block/dataplane/virtio-blk.c into hw/block/virtio-blk.c, merging
VirtIOBlockDataPlane's fields into VirtIOBlock.
hw/block/virtio-blk.c used VirtIOBlock->dataplane to check if
virtio_blk_data_plane_create() was successful. This is not necessary
because ->dataplane_started and ->dataplane_disabled can be used
instead. This patch makes those changes in order to drop
VirtIOBlock->dataplane.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240119135748.270944-2-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some ELF files really do have segments of zero size, e.g.:
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
RISCV_ATTRIBUT 0x00000000000025b8 0x0000000000000000 0x0000000000000000
0x000000000000003e 0x0000000000000000 R 0x1
LOAD 0x0000000000001000 0x0000000080200000 0x0000000080200000
0x00000000000001d1 0x00000000000001d1 R E 0x1000
LOAD 0x00000000000011d1 0x00000000802001d1 0x00000000802001d1
0x0000000000000e37 0x0000000000000e37 RW 0x1000
LOAD 0x0000000000000120 0x0000000000000000 0x0000000000000000
0x0000000000000000 0x0000000000000000 0x1000
The current logic does not check for this condition, resulting in
the incorrect assignment of 'lowaddr' as zero.
There is already a piece of codes inside the segment traversal loop
that checks for zero-sized loadable segments for not creating empty
ROM blobs. Let's move this check to the beginning of the loop to
cover both scenarios.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240116155049.390301-1-bmeng@tinylab.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
ISM devices are sensitive to manipulation of the IOMMU, so the ISM device
needs to be reset before the vfio-pci device is reset (triggering a full
UNMAP). In order to ensure this occurs, trigger ISM device resets from
subsystem_reset before triggering the PCI bus reset (which will also
trigger vfio-pci reset). This only needs to be done for ISM devices
which were enabled for use by the guest.
Further, ensure that AIF is disabled as part of the reset event.
Fixes: ef1535901a ("s390x: do a subsystem reset before the unprotect on reboot")
Fixes: 03451953c7 ("s390x/pci: reset ISM passthrough devices on shutdown and system reset")
Reported-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-ID: <20240118185151.265329-4-mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Use a flag to keep track of whether AIF is currently enabled. This can be
used to avoid enabling/disabling AIF multiple times as well as to determine
whether or not it should be disabled during reset processing.
Fixes: d0bc7091c2 ("s390x/pci: enable adapter event notification for interpreted devices")
Reported-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-ID: <20240118185151.265329-2-mjrosato@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
j is used while loading an ELF file to byteswap segments'
data. If data is larger than 2GB an overflow may happen.
So j should be elf_word.
This commit fixes a minor bug: it's unlikely anybody is trying to
load ELF files with 2GB+ segments for wrong-endianness targets,
but if they did, it wouldn't work correctly.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: 7ef295ea5b ("loader: Add data swap option to load-elf")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SYSCFG input GPIOs aren't connected yet. When the STM32L4x5 GPIO
device will be implemented, its output GPIOs will be connected to the
SYSCFG input GPIOs.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240109194438.70934-3-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Although very similar to the STM32F4xx EXTI, STM32L4x5 EXTI generates
more than 32 event/interrupt requests and thus uses more registers
than STM32F4xx EXTI which generates 23 event/interrupt requests.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240109160658.311932-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix device presence checking in the virtio-ccw qtest
* Support codespell checking in checkpatch.pl
* Fix emulation of LAE s390x instruction
* Work around htags bug when environment is large
* Some other small clean-ups here and there
-----BEGIN PGP SIGNATURE-----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=F/j2
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-01-11' of https://gitlab.com/thuth/qemu into staging
* Fix non-deterministic failures of the 'netdev-socket' qtest
* Fix device presence checking in the virtio-ccw qtest
* Support codespell checking in checkpatch.pl
* Fix emulation of LAE s390x instruction
* Work around htags bug when environment is large
* Some other small clean-ups here and there
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmWgHlgRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXAnBAAjQve/Jmfp9p8eQmswG7cl/a2TuJ59b9X
# SFRja2PprV/Wp4kxxEJX4er9F2+rlMusNL62LBp/QjZi9u4lCvCmuB7sMa0wEkjr
# BPPBrkxkAT+/8vhGpYg2GrxZv/UOLkycp3sjEp4v5yXWQw+OEBnkZZ+AuHddpnEr
# NKMKss71uQmccvuzD5FMDfbJQcSBD/yGPyFfDrv1RKreYRlbkEDVlcVoZpfoMwQY
# Pl167iDdmjVtsT+4wf8vHo5W/AYKDOjlV6AoujCnJVZnGx6BtDLiF/iNJ/VU1Ty5
# cRxySPT64HG+cGrbRqz9IjDvs++WW5EQn1jPY8NO2XFz3sney6Cs/pLKjqJY9S7P
# kfOXOBZG3zOI1kgd/CSR5b4szg4XvtTZaupczKiGOpYC9klf0oQNXGU5jXi3Csop
# Q332oUgiPeNdOx/4tXobFX6RwVCqLRYZbHx9RRYSxWlqJJPAB74/n+RZsmOtsxuJ
# RaiPKDmbVlslkUm78gIa5e6DMwDk2wmlkqa64W7VZxyqfQTRDPiPvfMGePkj6tmZ
# h9vUsELwwORlHpZyL08n0fzs3aeIYwzPwhfr+5iQZIawIp4Zqo8i8Lic/WfIlok9
# rmPIA0mjs1VtrUsroItw4NcY04xcVa7hkhz4EbkZROrfGamdkLuvbk2OKuOeoL0U
# lpgtQL6jA7E=
# =F/j2
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 11 Jan 2024 16:59:04 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-01-11' of https://gitlab.com/thuth/qemu:
.gitlab-ci.d/buildtest.yml: Work around htags bug when environment is large
tests/tcg/s390x: Test LOAD ADDRESS EXTENDED
target/s390x: Fix LAE setting a wrong access register
scripts/checkpatch: Support codespell checking
hw/s390x/ccw: Replace dirname() with g_path_get_dirname()
hw/s390x/ccw: Replace basename() with g_path_get_basename()
target/s390x/kvm/pv: Provide some more useful information if decryption fails
gitlab: fix s390x tag for avocado-system-centos
tests/qtest/virtio-ccw: Fix device presence checking
qtest: ensure netdev-socket tests have non-overlapping names
net: handle QIOTask completion to report useful error message
net: add explicit info about connecting/listening state
Revert "tests/qtest/netdev-socket: Raise connection timeout to 120 seconds"
Revert "osdep: add getloadavg"
Revert "netdev: set timeout depending on loadavg"
qtest: use correct boolean type for failover property
q800: move dp8393x_prom memory region to Q800MachineState
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZZ/QKgAKCRBAov/yOSY+
34eqBADA48++Z9gETFNheLUHdYEaja2emn+gSaoHLFquyq/l53w8RfrUII+BzV1o
T7D8xjlVQldAYZzqQn2pQe2S7r4ggfeNmxGxwJbCTW9sooGMwBnU8+Ix3ruSet7K
gI+UHLU4oHk6jdrT384tux2EG+qUmlLN1c7j4G/z1OzKEwFv7Q==
=+Pi0
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20240111' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20240111
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZZ/QKgAKCRBAov/yOSY+
# 34eqBADA48++Z9gETFNheLUHdYEaja2emn+gSaoHLFquyq/l53w8RfrUII+BzV1o
# T7D8xjlVQldAYZzqQn2pQe2S7r4ggfeNmxGxwJbCTW9sooGMwBnU8+Ix3ruSet7K
# gI+UHLU4oHk6jdrT384tux2EG+qUmlLN1c7j4G/z1OzKEwFv7Q==
# =+Pi0
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 11 Jan 2024 11:25:30 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20240111' of https://gitlab.com/gaosong/qemu:
hw/intc/loongarch_extioi: Add vmstate post_load support
hw/intc/loongarch_extioi: Add dynamic cpu number support
hw/loongarch/virt: Set iocsr address space per-board rather than percpu
hw/intc/loongarch_ipi: Use MemTxAttrs interface for ipi ops
target/loongarch: Add loongarch kvm into meson build
target/loongarch: Implement set vcpu intr for kvm
target/loongarch: Restrict TCG-specific code
target/loongarch: Implement kvm_arch_handle_exit
target/loongarch: Implement kvm_arch_init_vcpu
target/loongarch: Implement kvm_arch_init function
target/loongarch: Implement kvm get/set registers
target/loongarch: Supplement vcpu env initial when vcpu reset
target/loongarch: Define some kvm_arch interfaces
linux-headers: Synchronize linux headers from linux v6.7.0-rc8
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On LoongArch physical machine, one extioi interrupt controller only
supports 4 cpus. With processor more than 4 cpus, there are multiple
extioi interrupt controllers; if interrupts need to be routed to
other cpus, they are forwarded from extioi node0 to other extioi nodes.
On virt machine model, there is simple extioi interrupt device model.
All cpus can access register of extioi interrupt controller, however
interrupt can only be route to 4 vcpu for compatible with old kernel.
This patch adds dynamic cpu number support about extioi interrupt.
With old kernel legacy extioi model is used, however kernel can detect
and choose new route method in future, so that interrupt can be routed to
all vcpus.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-4-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
LoongArch system has iocsr address space, most iocsr registers are
per-board, however some iocsr register spaces banked for percpu such
as ipi mailbox and extioi interrupt status. For banked iocsr space,
each cpu has the same iocsr space, but separate data.
This patch changes iocsr address space per-board rather percpu,
for iocsr registers specified for cpu, MemTxAttrs.requester_id
can be parsed for the cpu. With this patches, the total address space
on board will be simple, only iocsr address space and system memory,
rather than the number of cpu and system memory.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
There is no need to dynamically allocate the memory region from the heap.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231227210212.245106-1-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Update the GPEX host bridge properties related to MMIO ranges with
values set for the virt machine.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231218150247.466427-12-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
ACPI DSDT generator needs information like ECAM range, PIO range, 32-bit
and 64-bit PCI MMIO range etc related to the PCI host bridge. Instead of
making these values machine specific, create properties for the GPEX
host bridge with default value 0. During initialization, the firmware
can initialize these properties with correct values for the platform.
This basically allows DSDT generator code independent of the machine
specific memory map accesses.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231218150247.466427-11-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some macros and static function related to IMSIC are defined in virt.c.
They are required in virt-acpi-build.c. So, make them public.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231218150247.466427-5-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V also needs to create the virtio in DSDT in the same way as ARM.
So, instead of duplicating the code, move this function to the device
specific file which is common across architectures.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231218150247.466427-3-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V also needs to use the same code to create fw_cfg in DSDT. So,
avoid code duplication by moving the code in arm and riscv to a device
specific file.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231218150247.466427-2-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
A SoC will not have a direct access to the NVIC embedded in its ARM
core. By aliasing the "num-prio-bits" property similarly to what is
done for the "num-irq" one, a SoC can easily configure it on its
armv7m instance.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240106181503.1746200-3-sam@rfc1149.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds a new STM32L4x5 SoC, it is necessary to add support for
the B-L475E-IOT01A board.
The implementation is derived from the STM32F405 SoC.
The implementation contains no peripherals, only memory regions are
implemented.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240108135849.351719-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As previously done for the sPAPR and legacy IOMMU backends, convert
the VFIOIOMMUOps struct to a QOM interface. The set of of operations
for this backend can be referenced with a literal typename instead of
a C struct.
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move vfio_spapr_container_setup() to a VFIOIOMMUClass::setup handler
and convert the sPAPR VFIOIOMMUOps struct to a QOM interface. The
sPAPR QOM interface inherits from the legacy QOM interface because
because both have the same basic needs. The sPAPR interface is then
extended with the handlers specific to the sPAPR IOMMU.
This allows reuse and provides better abstraction of the backends. It
will be useful to avoid compiling the sPAPR IOMMU backend on targets
not supporting it.
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
This will help in converting the sPAPR IOMMU backend to a QOM interface.
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Convert the legacy VFIOIOMMUOps struct to the new VFIOIOMMU QOM
interface. The set of of operations for this backend can be referenced
with a literal typename instead of a C struct. This will simplify
support of multiple backends.
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
VFIOContainerBase was not introduced as an abstract QOM object because
it felt unnecessary to expose all the IOMMU backends to the QEMU
machine and human interface. However, we can still abstract the IOMMU
backend handlers using a QOM interface class. This provides more
flexibility when referencing the various implementations.
Simply transform the VFIOIOMMUOps struct in an InterfaceClass and do
some initial name replacements. Next changes will start converting
VFIOIOMMUOps.
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
This allows to abstract a bit more the sPAPR IOMMU support in the
legacy IOMMU backend.
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Tested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
There is no universal BIOS, each machine needs a specific one.
Move the machine-specific definitions to each machine code and
remove this bogus header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20231122184334.18201-1-philmd@linaro.org>
xive2_regs.h only requires declarations from "qemu/bswap.h".
Include it instead of the huge target-specific "cpu.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20231122183920.17905-1-philmd@linaro.org>
'next_cpu' was converted to 'node' in commit bdc44640cb
("cpu: Use QTAILQ for CPU list").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231129183243.15859-1-philmd@linaro.org>
The dynamic state tracing was removed in commit d0aaf08bb9.
Fixes: d0aaf08bb9 ("tcg: remove the final vestiges of dstate")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231129182734.15565-1-philmd@linaro.org>
Add a helper to return a machine default CPU type.
If this machine is restricted to a single CPU type,
use it as default, obviously.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231116163726.28952-1-philmd@linaro.org>
Add helper cpu_model_from_type() to extract the CPU model name from
the CPU type name in two circumstances: (1) The CPU type name is the
combination of the CPU model name and suffix. (2) The CPU type name
is same to the CPU model name.
The helper will be used in the subsequent commits to conver the
CPU type name to the CPU model name.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231114235628.534334-6-gshan@redhat.com>
[PMD: Mention returned string must be released with g_free()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the memory listener to a common place rather than always in the
first / last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-14-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The memory listener functions can call these too. Make vdpa_iommu work
with VhostVDPAShared.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-13-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callers only have the shared information by the end of this series.
Start converting this functions.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-12-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the iommu_list member to VhostVDPAShared so all vhost_vdpa can use
it, rather than always in the first / last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-11-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It is always VHOST_IOTLB_MSG_V2. We can always make it back per
vhost_dev if needed.
This change makes easier for vhost_vdpa_map and unmap not to depend on
vhost_vdpa but only in VhostVDPAShared.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-10-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the backend_cap member to VhostVDPAShared so all vhost_vdpa can use
it, rather than always in the first / last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-9-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the iotlb_batch_begin_sent member to VhostVDPAShared so all
vhost_vdpa can use it, rather than always in the first / last
vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-8-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the file descriptor to VhostVDPAShared so all vhost_vdpa can use
it, rather than always in the first / last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-7-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the shadow_data member to VhostVDPAShared so all vhost_vdpa can use
it, rather than always in the first or last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-5-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the iova range to VhostVDPAShared so all vhost_vdpa can use it,
rather than always in the first or last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-4-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will register the vhost_vdpa memory listener while the VM
is migrating at the destination, so we can map the memory to the device
before stopping the VM at the source. The main goal is to reduce the
downtime.
However, the destination QEMU is unaware of which vhost_vdpa device will
register its memory_listener. If the source guest has CVQ enabled, it
will be the CVQ device. Otherwise, it will be the first one.
Move the iova tree to VhostVDPAShared so all vhost_vdpa can use it,
rather than always in the first or last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-3-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will hold properties shared among all vhost_vdpa instances associated
with of the same device. For example, we just need one iova_tree or one
memory listener for the entire device.
Next patches will register the vhost_vdpa memory listener at the
beginning of the VM migration at the destination. This enables QEMU to
map the memory to the device before stopping the VM at the source,
instead of doing while both source and destination are stopped, thus
minimizing the downtime.
However, the destination QEMU is unaware of which vhost_vdpa struct will
register its memory_listener. If the source guest has CVQ enabled, it
will be the one associated with the CVQ. Otherwise, it will be the
first one.
Save the memory operations related members in a common place rather than
always in the first / last vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20231221174322.3130442-2-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds support for vhost-scsi to be able to create a worker thread
per virtqueue. Right now for vhost-net we get a worker thread per
tx/rx virtqueue pair which scales nicely as we add more virtqueues and
CPUs, but for scsi we get the single worker thread that's shared by all
virtqueues. When trying to send IO to more than 2 virtqueues the single
thread becomes a bottlneck.
This patch adds a new setting, worker_per_virtqueue, which can be set
to:
false: Existing behavior where we get the single worker thread.
true: Create a worker per IO virtqueue.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20231204231618.21962-3-michael.christie@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
This adds the vhost backend callouts for the worker ioctls added in the
6.4 linux kernel commit:
c1ecd8e95007 ("vhost: allow userspace to create workers")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20231204231618.21962-2-michael.christie@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZYPyvQAKCRBAov/yOSY+
38/vBADT3b+Wo/2AeXOO3OXOM1VBhIvzDjY1OWytuJpkF3JGW45cMLqgtIgMj8h7
NtzRS3JbFYbYuxITeeo1Ppl6dAD0pCZjIU6OCBxAJ6ADPsE/xD8nYWrMGqYVXg7E
hN0Cno2sf6dmJ0QxUxn7G+cUuvNtnGaDSZE+RAkjtzq1nvx7CQ==
=mte5
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20231221' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20231221
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZYPyvQAKCRBAov/yOSY+
# 38/vBADT3b+Wo/2AeXOO3OXOM1VBhIvzDjY1OWytuJpkF3JGW45cMLqgtIgMj8h7
# NtzRS3JbFYbYuxITeeo1Ppl6dAD0pCZjIU6OCBxAJ6ADPsE/xD8nYWrMGqYVXg7E
# hN0Cno2sf6dmJ0QxUxn7G+cUuvNtnGaDSZE+RAkjtzq1nvx7CQ==
# =mte5
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 21 Dec 2023 03:09:33 EST
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20231221' of https://gitlab.com/gaosong/qemu:
target/loongarch: Add timer information dump support
hw/loongarch/virt: Align high memory base address with super page size
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add the iothread-vq-mapping parameter to assign virtqueues to IOThreads.
Store the vq:AioContext mapping in the new struct
VirtIOBlockDataPlane->vq_aio_context[] field and refactor the code to
use the per-vq AioContext instead of the BlockDriverState's AioContext.
Reimplement --device virtio-blk-pci,iothread= and non-IOThread mode by
assigning all virtqueues to the IOThread and main loop's AioContext in
vq_aio_context[], respectively.
The comment in struct VirtIOBlockDataPlane about EventNotifiers is
stale. Remove it.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20231220134755.814917-5-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
virtio-blk and virtio-scsi devices will need a way to specify the
mapping between IOThreads and virtqueues. At the moment all virtqueues
are assigned to a single IOThread or the main loop. This single thread
can be a CPU bottleneck, so it is necessary to allow finer-grained
assignment to spread the load.
Introduce DEFINE_PROP_IOTHREAD_VQ_MAPPING_LIST() so devices can take a
parameter that maps virtqueues to IOThreads. The command-line syntax for
this new property is as follows:
--device '{"driver":"foo","iothread-vq-mapping":[{"iothread":"iothread0","vqs":[0,1,2]},...]}'
IOThreads are specified by name and virtqueues are specified by 0-based
index.
It will be common to simply assign virtqueues round-robin across a set
of IOThreads. A convenient syntax that does not require specifying
individual virtqueue indices is available:
--device '{"driver":"foo","iothread-vq-mapping":[{"iothread":"iothread0"},{"iothread":"iothread1"},...]}'
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20231220134755.814917-4-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qdev_alias_all_properties() aliases a DeviceState's qdev properties onto
an Object. This is used for VirtioPCIProxy types so that --device
virtio-blk-pci has properties of its embedded --device virtio-blk-device
object.
Currently this function is implemented using qdev properties. Change the
function to use QOM object class properties instead. This works because
qdev properties create QOM object class properties, but it also catches
any QOM object class-only properties that have no qdev properties.
This change ensures that properties of devices are shown with --device
foo,\? even if they are QOM object class properties.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20231220134755.814917-2-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The AioContext lock no longer has any effect. Remove it.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-ID: <20231205182011.1976568-9-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Protect the Task Management Function BH state with a lock. The TMF BH
runs in the main loop thread. An IOThread might process a TMF at the
same time as the TMF BH is running. Therefore tmf_bh_list and tmf_bh
must be protected by a lock.
Run TMF request completion in the IOThread using aio_wait_bh_oneshot().
This avoids more locking to protect the virtqueue and SCSI layer state.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231205182011.1976568-2-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Stop depending on the AioContext lock and instead access
SCSIDevice->requests from only one thread at a time:
- When the VM is running only the BlockBackend's AioContext may access
the requests list.
- When the VM is stopped only the main loop may access the requests
list.
These constraints protect the requests list without the need for locking
in the I/O code path.
Note that multiple IOThreads are not supported yet because the code
assumes all SCSIRequests are executed from a single AioContext. Leave
that as future work.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-ID: <20231204164259.1515217-2-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
s->rq is accessed from IO_CODE and GLOBAL_STATE_CODE. Introduce a lock
to protect s->rq and eliminate reliance on the AioContext lock.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20230914140101.1065008-3-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With LoongArch virt machine, there is low memory space with region
0--0x10000000, and high memory space with started from 0x90000000.
High memory space is aligned with 256M, it will be better if it is
aligned with 1G, which is super page aligned for 4K page size.
Currently linux kernel and uefi bios has no limitation with high
memory base address, it is ok to set high memory base address
with 0x80000000.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231127040231.4123715-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
* Some header clean-ups by Philippe
* Restrict type names to alphanumerical range (and a few special characters)
* Fix analyze-migration.py script on s390x
* Clean up and improve some tests
* Document handling of commas in CLI options parameters
-----BEGIN PGP SIGNATURE-----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=TA1/
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-12-20' of https://gitlab.com/thuth/qemu into staging
* Add compat machines for QEMU 9.0
* Some header clean-ups by Philippe
* Restrict type names to alphanumerical range (and a few special characters)
* Fix analyze-migration.py script on s390x
* Clean up and improve some tests
* Document handling of commas in CLI options parameters
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmWCtYsRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWLnw//cNJrxG0V+j0iakX+C7HRumVrLBDI4KYY
# Cp2Hx92SyeQ0Kk8DJS6JueTV0SLjMsV77APu2YPH7ELmPlk+CB9gqmV7xVoYNvsm
# QbRPlIjFw8MHLekadc2A+C+pn48tWACoOdBEDIfazKrxybnf0B57RC/fIfMKHjbs
# 2ALCoFbbgphs7yWuzTHK8ayKaGMhUVkWfzHQwpnq899olHyZBhkl951uKJA6VmLx
# KvggePkpszLjmmXA8MH1hDCcizki31cB0ZKTbQFCyE42s2S3Hvg0GueU90O7Y1cj
# lS5tPVQxyEhUYMLL+/hudlf2OYqVn2BalB7ieUQIy6rG8yoc9zxfIKQi0ccl+2oA
# s8HRq5S0bSjtilQogU1LQL/Gk6W1/N9MmnhKvCGB+BTK5KX7s4EQk02y9gGZm/8s
# pMErMyaXTG4dLiTAK42VgMVDqCYvzBmE+Gj91OmoUR7fb+VMrsWxeBFxMPDn+VtL
# TMJegIFsjw2QCSitcU4v+nP0qtKgXGbuZtrGXKabrxH5PmeQFJDSM7TwpTK4qvjK
# QMIQKBbz8BfJnUzN8qAaaJEpp1T5tcMJClKtfcgxq/+VyaSaHLmD0cljqBC+g+y7
# FTo+fa7oYx44sAlqapdEXBSGn4T+J26iuCef13CCCiPfYBv/tk3b2E0AWHj4y58I
# +VpInjUaPBQ=
# =TA1/
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 20 Dec 2023 04:36:11 EST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-12-20' of https://gitlab.com/thuth/qemu:
tests/unit/test-qmp-event: Replace fixture by global variables
tests/unit/test-qmp-event: Simplify event emission check
tests/unit/test-qmp-event: Drop superfluous mutex
tests/qtest/npcm7xx_pwm-test: Only do full testing in slow mode
qemu-options: Clarify handling of commas in options parameters
tests/qtest/migration-test: Fix analyze-migration.py for s390x
qom/object: Limit type names to alphanumerical and some few special characters
tests/unit/test-io-task: Rename "qemu:dummy" to avoid colon in the name
memory: Remove "qemu:" prefix from the "qemu:ram-discard-manager" type name
hw: Replace anti-social QOM type names (again)
docs/system/arm: Fix for rename of type "xlnx.bbram-ctrl"
target: Restrict 'sysemu/reset.h' to system emulation
hw/s390x/ipl: Remove unused 'exec/exec-all.h' included header
hw/misc/mips_itu: Remove unnecessary 'exec/exec-all.h' header
hw/ppc/spapr_hcall: Remove unused 'exec/exec-all.h' included header
system/qtest: Restrict QTest API to system emulation
system/qtest: Include missing 'hw/core/cpu.h' header
MAINTAINERS: Add some more vmware-related files to the corresponding section
hw: Add compat machines for 9.0
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* arm/kvm: drop the split between "common KVM support" and
"64-bit KVM support", since 32-bit Arm KVM no longer exists
* arm/kvm: clean up APIs to be consistent about CPU arguments
* Don't implement *32_EL2 registers when EL1 is AArch64 only
* Restrict DC CVAP & DC CVADP instructions to TCG accel
* Restrict TCG specific helpers
* Propagate MDCR_EL2.HPMN into PMCR_EL0.N
* Include missing 'exec/exec-all.h' header
* fsl-imx: add simple RTC emulation for i.MX6 and i.MX7 boards
-----BEGIN PGP SIGNATURE-----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=GWIA
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20231219' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* arm/kvm: drop the split between "common KVM support" and
"64-bit KVM support", since 32-bit Arm KVM no longer exists
* arm/kvm: clean up APIs to be consistent about CPU arguments
* Don't implement *32_EL2 registers when EL1 is AArch64 only
* Restrict DC CVAP & DC CVADP instructions to TCG accel
* Restrict TCG specific helpers
* Propagate MDCR_EL2.HPMN into PMCR_EL0.N
* Include missing 'exec/exec-all.h' header
* fsl-imx: add simple RTC emulation for i.MX6 and i.MX7 boards
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmWB6o0ZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3mxMEACRpRxJ81pLs8fFYC5BgRhU
# BCxr+ZqarBygzsH9YWUN2TFFKlEZi7mLu6lzFsfN/qEmYCg8VslPbulQHqcGkx51
# kVxXFp/KuGlKt4zGRagZUJxgYAwwU5mnK6dTZT5/ZF6yWX67dXn8V7MP9lqqEPw5
# 5gut7Mu4f7MiAQbwZY1CWP+iu5uZmdsBuKxA6zkxOWJh/A1SfaqQRO6xVQttLAxS
# DPMTpQGmwPS4I+3gGNnqlSu6etp2tdy2K0cW3fhMp6hx70uNMHmFNzRhT/6TaKka
# 9AqXQsFHQiFXDGAm6PmCvfQI6KpLljDyNL/TuUkQWi72bGEHjUsJAdG0aXVOa30W
# uC7vuJkdZrP/t5P1AkZhWQUrlawDRV2YHNDD+gY4fxJL/STkGyU6M8R1nm1J+InN
# n0SeK0VHRC6DRPXCMQhC5QwKUH6ZjFZRs/r2opTu9p+ThQAQRmZBiVfdISCDMYnN
# DCiSb78gIFaUkwtiP44qq8MJQjsHnXtTD1Akqyo2fXSKs66jDK9Gnc8gENYdpghe
# 7V36bOp6scROHOB2a/r8gT42RKzSN6uh6xByaaToza63/bPgvHnn8vvQQbB01AgX
# zJC1xs3dwY8JMyqDefda0K0NDPS8TzNsXYmgxxxcQJpUvB4VVjet9VIMF3T+d8HO
# Pas41Z1gsQY+rcaRk/9mPA==
# =GWIA
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 19 Dec 2023 14:10:05 EST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20231219' of https://git.linaro.org/people/pmaydell/qemu-arm: (43 commits)
fsl-imx: add simple RTC emulation for i.MX6 and i.MX7 boards
target/arm/helper: Propagate MDCR_EL2.HPMN into PMCR_EL0.N
target/arm/tcg: Including missing 'exec/exec-all.h' header
target/arm: Restrict DC CVAP & DC CVADP instructions to TCG accel
target/arm: Restrict TCG specific helpers
target/arm: Don't implement *32_EL2 registers when EL1 is AArch64 only
target/arm/kvm: Have kvm_arm_hw_debug_active take a ARMCPU argument
target/arm/kvm: Have kvm_arm_handle_debug take a ARMCPU argument
target/arm/kvm: Have kvm_arm_handle_dabt_nisv take a ARMCPU argument
target/arm/kvm: Have kvm_arm_verify_ext_dabt_pending take a ARMCPU arg
target/arm/kvm: Have kvm_arm_[get|put]_virtual_time take ARMCPU argument
target/arm/kvm: Have kvm_arm_vcpu_finalize take a ARMCPU argument
target/arm/kvm: Have kvm_arm_vcpu_init take a ARMCPU argument
target/arm/kvm: Have kvm_arm_pmu_set_irq take a ARMCPU argument
target/arm/kvm: Have kvm_arm_pmu_init take a ARMCPU argument
target/arm/kvm: Have kvm_arm_pvtime_init take a ARMCPU argument
target/arm/kvm: Have kvm_arm_set_device_attr take a ARMCPU argument
target/arm/kvm: Have kvm_arm_sve_get_vls take a ARMCPU argument
target/arm/kvm: Have kvm_arm_sve_set_vls take a ARMCPU argument
target/arm/kvm: Have kvm_arm_add_vcpu_properties take a ARMCPU argument
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
QOM type names containing ',' result in awful UI. We got rid of them
in v6.0.0 (commit e178113ff6 hw: Replace anti-social QOM type names).
A few have crept back since:
xlnx,cframe-reg
xlnx,efuse
xlnx,pmc-efuse-cache
xlnx,versal-cfu-apb
xlnx,versal-cfu-fdro
xlnx,versal-cfu-sfr
xlnx,versal-crl
xlnx,versal-efuse
xlnx,zynqmp-efuse
These are all device types. They can't be plugged with -device /
device_add, except for "xlnx,efuse" (I'm not sure that one is
intentional).
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-aarch64 -device xlnx,,pmc-efuse-cache,help
They can also be used with -global, where you must *not* double the
comma:
$ qemu-system-aarch64 -global xlnx,efuse.drive-index=2
Trap for the unwary.
"xlnx,efuse", "xlnx,versal-efuse", "xlnx,pmc-efuse-cache",
"xlnx-zynqmp-efuse" are from v6.2.0, "xlnx,versal-crl" is from v7.1.0,
and the remainder are new.
Rename them all to "xlnx-FOO", like commit e178113ff6 did.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-ID: <20231117114457.177308-3-thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Introduce a helper function to replace the common code to initialize
VFIODevice in pci, platform, ap and ccw VFIO device.
No functional change intended.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Some of the callbacks in VFIOIOMMUOps pass VFIOContainerBase poiner,
those callbacks only need read access to the sub object of VFIOContainerBase.
So make VFIOContainerBase, VFIOContainer and VFIOIOMMUFDContainer as const
in these callbacks.
Local functions called by those callbacks also need same changes to avoid
build error.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
This gives management tools like libvirt a chance to open the vfio
cdev with privilege and pass FD to qemu. This way qemu never needs
to have privilege to open a VFIO or iommu cdev node.
Together with the earlier support of pre-opening /dev/iommu device,
now we have full support of passing a vfio device to unprivileged
qemu by management tool. This mode is no more considered for the
legacy backend. So let's remove the "TODO" comment.
Add helper functions vfio_device_set_fd() and vfio_device_get_name()
to set fd and get device name, they will also be used by other vfio
devices.
There is no easy way to check if a device is mdev with FD passing,
so fail the x-balloon-allowed check unconditionally in this case.
There is also no easy way to get BDF as name with FD passing, so
we fake a name by VFIO_FD[fd].
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Legacy vfio pci and iommufd cdev have different process to hot reset
vfio device, expand current code to abstract out pci_hot_reset callback
for legacy vfio, this same interface will also be used by iommufd
cdev vfio device.
Rename vfio_pci_hot_reset to vfio_legacy_pci_hot_reset and move it
into container.c.
vfio_pci_[pre/post]_reset and vfio_pci_host_match are exported so
they could be called in legacy and iommufd pci_hot_reset callback.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The iommufd backend is implemented based on the new /dev/iommu user API.
This backend obviously depends on CONFIG_IOMMUFD.
So far, the iommufd backend doesn't support dirty page sync yet.
Co-authored-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Introduce an empty spapr backend which will hold spapr specific
content, currently only prereg_listener and hostwin_list.
Also introduce two spapr specific callbacks add/del_window into
VFIOIOMMUOps. Instantiate a spapr ops with a helper setup_spapr_ops
and assign it to bcontainer->ops.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Meanwhile remove the helper function vfio_free_container as it
only calls g_free now.
No functional change intended.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move listener to base container. Also error and initialized fields
are moved at the same time.
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
In the prospect to get rid of VFIOContainer refs
in common.c lets convert misc functions to use the base
container object instead:
vfio_devices_all_dirty_tracking
vfio_devices_all_device_dirty_tracking
vfio_devices_all_running_and_mig_active
vfio_devices_query_dirty_bitmap
vfio_get_dirty_bitmap
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
VFIO Device is also changed to point to base container instead of
legacy container.
No functional change intended.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
dirty_pages_supported field is also moved to the base container
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move the space field to the base object. Also the VFIOAddressSpace
now contains a list of base containers.
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move the giommu_list field in the base container and store
the base container in the VFIOGuestIOMMU.
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
This adds two helper functions vfio_container_init/destroy which will be
used by both legacy and iommufd containers to do base container specific
initialization and release.
No functional change intended.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
This empty VFIOIOMMUOps named vfio_legacy_ops will hold all general
IOMMU ops of legacy container.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Introduce a dumb VFIOContainerBase object and its targeted interface.
This is willingly not a QOM object because we don't want it to be
visible from the user interface. The VFIOContainerBase will be
smoothly populated in subsequent patches as well as interfaces.
No functional change intended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
GUEST_VIRTIO_MMIO_* was added in Xen 4.17, so only define them
for CONFIG_XEN_CTRL_INTERFACE_VERSIONs up to 4.16.
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The VIA integrated south bridge chips combine several functions and
allow routing their interrupts to any of the ISA IRQs also allowing
multiple sources to share the same ISA IRQ. E.g. pegasos2 firmware
configures everything to use IRQ 9 but amigaone routes them to
separate ISA IRQs so the current simplified routing does not work.
Bring back via_isa_set_irq() and change it to take the component that
wants to change an IRQ and keep track of interrupt status of each
source separately and do the mapping to ISA IRQ within the ISA bridge.
This may not handle cases when an ISA IRQ is controlled by devices
directly, not going through via_isa_set_irq() such as serial, parallel
or keyboard but these IRQs being conventionally fixed are not likely
to be change by guests or share with other devices so this does not
cause a problem in practice.
This reverts commit 4e5a20b6da.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <1c3902d4166234bef0a476026441eaac3dd6cda5.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
It seems that the url changed a bit, and it triggers an error. Fix the URLs so
the documentation can be reached again.
Signed-off-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20231124143505.1493184-3-fkonrad@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The spips, qspips, and zynqmp-qspips share the same realize function
(xilinx_spips_realize) and initialize their io memory region with different
mmio_ops passed through the class. The size of the memory region is set to
the largest area (0x200 bytes for zynqmp-qspips) thus it is possible to write
out of s->regs[addr] in xilinx_spips_write for spips and qspips.
This fixes that wrong behavior.
Reviewed-by: Luc Michel <luc.michel@amd.com>
Signed-off-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20231124143505.1493184-2-fkonrad@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The VirtioPCIDeviceTypeInfo structure, added in commit a4ee4c8baa
("virtio: Helper for registering virtio device types") got extended
in commit 8ea90ee690 ("virtio: add class_size") with the @class_size
field. Do similarly with the @instance_finalize field.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231121174051.63038-2-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function reads the value of the PCI_CLASS_PROG register for PCI IDE
controllers and configures the PCI BARs and/or IDE ioports accordingly.
In the case where we switch to legacy mode, the PCI BARs are set to return zero
(as suggested in the "PCI IDE Controller" specification), the legacy IDE ioports
are enabled, and the PCI interrupt pin cleared to indicate legacy IRQ routing.
Conversely when we switch to native mode, the legacy IDE ioports are disabled
and the PCI interrupt pin set to indicate native IRQ routing. The contents of
the PCI BARs are unspecified, but this is not an issue since if a PCI IDE
controller has been switched to native mode then its BARs will need to be
programmed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These definitions are present in ioport.c which is currently only available when
CONFIG_IDE_ISA is enabled. Move them to the IDE core so that they can be made
available to PCI IDE controllers that support switching to legacy mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The 'stm32vldiscovery' machine ignores the CPU type requested by
the command line. This might confuse users, since the following
will create a machine with a Cortex-M3 CPU:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
qemu-system-aarch64: Invalid CPU type: neoverse-n1-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'netduino2' machine ignores the CPU type requested by the
command line. This might confuse users, since the following will
create a machine with a Cortex-M3 CPU:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
qemu-system-arm: Invalid CPU type: cortex-a9-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both 'netduinoplus2' and 'olimex-stm32-h405' machines ignore the
CPU type requested by the command line. This might confuse users,
since the following will create a machine with a Cortex-M4 CPU:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
qemu-system-aarch64: Invalid CPU type: cortex-r5f-arm-cpu
The valid types are: cortex-m4-arm-cpu
Since the SoC family can only use Cortex-M4 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Constify MachineClass::valid_cpu_types[i], as suggested by Richard
Henderson.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231117071704.35040-2-philmd@linaro.org
[PMD: Constify HPPA machines,
restrict valid_cpu_types to machine_class_init() handlers]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: 388d6b574e "hw/cxl: Use switch statements for read and write of cachemem registers"
Fixes: 3314efd276 "hw/cxl/mbox: Add Physical Switch Identify command."
Fixes: 004e3a93b8 "hw/cxl: Add tunneled command support to mailbox for switch cci."
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Until now, array properties are actually implemented with a hack that
uses multiple properties on the QOM level: a static "foo-len" property
and after it is set, dynamically created "foo[i]" properties.
In external interfaces (-device on the command line and device_add in
QMP), this interface was broken by commit f3558b1b ('qdev: Base object
creation on QDict rather than QemuOpts') because QDicts are unordered
and therefore it could happen that QEMU tried to set the indexed
properties before setting the length, which fails and effectively makes
array properties inaccessible. In particular, this affects the 'ports'
property of the 'rocker' device, which used to be configured like this:
-device rocker,len-ports=2,ports[0]=dev0,ports[1]=dev1
This patch reworks the external interface so that instead of using a
separate top-level property for the length and for each element, we use
a single true array property that accepts a list value. In the external
interfaces, this is naturally expressed as a JSON list and makes array
properties accessible again. The new syntax looks like this:
-device '{"driver":"rocker","ports":["dev0","dev1"]}'
Creating an array property on the command line without using JSON format
is currently not possible. This could be fixed by switching from
QemuOpts to a keyval parser, which however requires consideration of the
compatibility implications.
All internal users of devices with array properties go through
qdev_prop_set_array() at this point, so updating it takes care of all of
them.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1090
Fixes: f3558b1b76
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231109174240.72376-12-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This queue, the last one before the 8.2 feature freeze, has miscellanous
changes that includes new PowerNV features and the new AmigaONE XE
board.
-----BEGIN PGP SIGNATURE-----
iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZUqiORYcZGFuaWVsaGI0
MTNAZ21haWwuY29tAAoJEDzZypbeAzFkBSUA/2qm8CyrRqY5+tsjtWQqZmPZ3L1F
CgnXFNqtY2tzbTe5AQCi6FeQBEmXbZYVfryZyA+CQ4DUERc+18pe6hV3bBR9Cg==
=cnHS
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20231107' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2023-11-07:
This queue, the last one before the 8.2 feature freeze, has miscellanous
changes that includes new PowerNV features and the new AmigaONE XE
board.
# -----BEGIN PGP SIGNATURE-----
#
# iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZUqiORYcZGFuaWVsaGI0
# MTNAZ21haWwuY29tAAoJEDzZypbeAzFkBSUA/2qm8CyrRqY5+tsjtWQqZmPZ3L1F
# CgnXFNqtY2tzbTe5AQCi6FeQBEmXbZYVfryZyA+CQ4DUERc+18pe6hV3bBR9Cg==
# =cnHS
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 08 Nov 2023 04:46:49 HKT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20231107' of https://gitlab.com/danielhb/qemu:
ppc: qtest already exports qtest_rtas_call()
hw/pci-host: Update PHB5 XSCOM registers
ppc/pnv: Fix number of I2C engines and ports for power9/10
ppc/pnv: Connect PNV I2C controller to powernv10
ppc/pnv: Connect I2C controller model to powernv9 chip
ppc/pnv: Add an I2C controller model
tests/avocado: Add test for amigaone board
hw/ppc: Add emulation of AmigaOne XE board
hw/pci-host: Add emulation of Mai Logic Articia S
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* Fix condition code problem in the CLC and LAALG instruction
* Fix ordering of the new s390x topology list entries
* Add some more files to the MAINTAINERS file
* Allow newer versions of Tesseract in the m68k nextcube test
-----BEGIN PGP SIGNATURE-----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=y+cC
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-11-07' of https://gitlab.com/thuth/qemu into staging
* Fix s390x CPU reconfiguration information in the SCLP facility map
* Fix condition code problem in the CLC and LAALG instruction
* Fix ordering of the new s390x topology list entries
* Add some more files to the MAINTAINERS file
* Allow newer versions of Tesseract in the m68k nextcube test
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmVKgksRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWIHg//TM3JOpsMEqHKlUKqOJH02mFQrK6H7LG0
# BC56FG7T+/mpYs1NTG92t8nCK03C2ZCweQWD7ZulRJAjPhZv+TF5bJEForivU7+k
# PKEshz9xKCWn2YGyNnf2LA06J1JkF215+KlReOoxwSgj1cPlHfBLQ0DtxmpJJZ1G
# h5p4d26BbSlwR58HrFWTlhgJMPenl59BETUGIK1FklBxunmZeeijddfniAhOT44y
# i0u9/H9KCg3tkwBROUy+42QV+ef32kz/yvi5RmYQI5W7PixO4sxH6MYduOjshsu9
# wK70f8EOwiZV6lFxqmbV7vxFeNnp5IuaVU7PMBoAkwZqLw99mSFy1+1BabCuL5b+
# 3iUTiD4UW48MYwE2Ua6Lit4kpfjhwcp/UYz6pIk6TCBQX6LfzO+nj+rod0GdIpyZ
# 4Lwm7jBtpTlYkGrsMvpA/qcidOtqPA1lmBTNlY1hFodQF6KWtyObn0w5AM80xeeU
# /mGxQDz97Bpz7LKZvhu+k38jaWvnJFnl3jF1zet88CYL9YL+YI/k1KjhFafCXb0V
# 38Xpt5JTWxyLSh2B3gx0OpokX5bftvW9GlLix0HqL7c23uYwR2Bq+Rd6I8SAlk4C
# uJq6gqP8IFBFHfgbmyqf/fyd/eHxm7J1voIdy9PZyxZ1JYT9A7yu56qV6SJYwCpr
# aARwui/Dm4o=
# =y+cC
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 08 Nov 2023 02:30:35 HKT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-11-07' of https://gitlab.com/thuth/qemu:
target/s390x/cpu topology: Fix ordering and creation of TLEs
tests/tcg/s390x: Test ADD LOGICAL WITH CARRY
tests/tcg/s390x: Test LAALG with negative cc_src
target/s390x: Fix LAALG not updating cc_src
tests/tcg/s390x: Test CLC with inaccessible second operand
target/s390x: Fix CLC corrupting cc_src
target/s390x/cpu_models: Use 'first_cpu' in s390_get_feat_block()
s390/sclp: fix SCLP facility map
tests/avocado: Allow newer versions of tesseract in the nextcube test
MAINTAINERS: Add artist.c to the hppa machine section
MAINTAINERS: Add the virtio-gpu documentation to the corresponding section
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Having two functions with the same name is a bad idea. As spapr only
uses the function locally, made it static.
When you compile with clang, you get this compilation error:
/usr/bin/ld: tests/qtest/libqos/libqos.fa.p/.._libqtest.c.o: in function `qtest_rtas_call':
/scratch/qemu/clang/full/all/../../../../../mnt/code/qemu/full/tests/qtest/libqtest.c:1195: multiple definition of `qtest_rtas_call'; libqemu-ppc64-softmmu.fa.p/hw_ppc_spapr_rtas.c.o:/scratch/qemu/clang/full/all/../../../../../mnt/code/qemu/full/hw/ppc/spapr_rtas.c:536: first defined here
clang-16: error: linker command failed with exit code 1 (use -v to see invocation)
ninja: build stopped: subcommand failed.
make: *** [Makefile:162: run-ninja] Error 1
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20231030163834.4638-1-quintela@redhat.com>
[dhb: remove 'spapr_rtas.h' include from spapr_rtas.c]
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add new XSCOM registers introduced in PHB5.
Apply bit-masks within xscom-write methods.
Bit-masks specified using PPC_BITMASK macro.
Signed-off-by: Saif Abrar <saif.abrar@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Message-ID: <20231016175948.10869-1-saif.abrar@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Power9 is supposed to have 4 PIB-connected I2C engines with the
following number of ports on each engine:
0: 2
1: 13
2: 2
3: 2
Power10 also has 4 engines but has the following number of ports
on each engine:
0: 14
1: 14
2: 2
3: 16
Current code assumes that they all have the same (maximum) number.
This can be a problem if software expects to see a certain number
of ports present (Power Hypervisor seems to care).
Fixed this by adding separate tables for power9 and power10 that
map the I2C controller number to the number of I2C buses that should
be attached for that engine.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Message-ID: <20231025152714.956664-1-milesg@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Wires up four I2C controller instances to the powernv10 chip
XSCOM address space.
Each controller instance is wired up to two I2C buses of
its own. No other I2C devices are connected to the buses
at this time.
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20231017221434.810363-1-milesg@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Wires up three I2C controller instances to the powernv9 chip
XSCOM address space.
Each controller instance is wired up to a single I2C bus of
its own. No other I2C devices are connected to the buses
at this time.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[milesg: Split wiring from addition of model itself]
[milesg: Added new commit message]
[milesg: Moved hardcoded attributes into PnvChipClass]
[milesg: Removed TODO comment for I2C]
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <20231016222013.3739530-3-milesg@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The more recent IBM power processors have an embedded I2C
controller that is accessible by software via the XSCOM
address space.
Each instance of the I2C controller is capable of controlling
multiple I2C buses (one at a time). Prior to beginning a
transaction on an I2C bus, the bus must be selected by writing
the port number associated with the bus into the PORT_NUM
field of the MODE register. Once an I2C bus is selected,
the status of the bus can be determined by reading the
Status and Extended Status registers.
I2C bus transactions can be started by writing a command to
the Command register and reading/writing data from/to the
FIFO register.
Not supported :
. 10 bit I2C addresses
. Multimaster
. Slave
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[milesg: Split wiring to powernv9 into its own commit]
[milesg: Added more detail to commit message]
[milesg: Added SPDX Licensed Identifier to new files]
[milesg: updated copyright dates]
[milesg: Added use of g_autofree]
[milesg: Added NULL check after pnv_i2c_get_bus]
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <20231016222013.3739530-2-milesg@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Qemu's SCLP implementation incorrectly reports that it supports CPU
reconfiguration. If a guest issues a CPU reconfiguration request it
is rejected as invalid command.
Fix the SCLP_HAS_CPU_INFO mask, and remove the unused
SCLP_CMDW_CONFIGURE_CPU and SCLP_CMDW_DECONFIGURE_CPU defines.
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Message-ID: <20231024100703.929679-1-hca@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The Articia S is a generic chipset supporting several different CPUs
that were among others used on some PPC boards. This is a minimal
emulation of the parts needed for emulating the AmigaOne board.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <83822787431701cf4d460298d3e3845f362e5da1.1698406922.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
VCAP is a register for devices with energy storage capacitors.
Reviewed-by: Benjamin Streb <bstreb@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-4-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PMBus devices may integrate fans whose operation is configurable
over PMBus. This commit allows the driver to read and write the
fan control registers but does not model the operation of fans.
Reviewed-by: Stephen Longfield <slongfield@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-3-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The VOUT_MODE command is described in the PMBus Specification,
Part II, Ver 1.3 Section 8.3
VOUT_MODE has a three bit mode and 4 bit parameter, the three bit
mode determines whether voltages are formatted as uint16, uint16,
VID, and Direct modes. VID and Direct modes use the remaining 5 bits
to scale the voltage readings.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-2-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PMBus devices can send and receive variable length data using the
block read and write format, with the first byte in the payload
denoting the length.
This is mostly used for strings and on-device logs. Devices can
respond to a block read with an empty string.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-1-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In the nr_threads' comment, specify it represents the
number of threads in the "core" to avoid confusion.
Also add comment for nr_dies in CPUX86State.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231024090323.1859210-5-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
For function comments in this file, keep the comment style consistent
with other files in the directory.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@Intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231024090323.1859210-2-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Fix:
hw/core/loader.c:1073:27: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
bool option_rom, MemoryRegion *mr,
^
include/sysemu/sysemu.h:57:22: note: previous declaration is here
extern QEMUOptionRom option_rom[MAX_OPTION_ROMS];
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20231010115048.11856-3-philmd@linaro.org>
Fix:
hw/core/machine.c:1302:22: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
const CPUArchId *cpus = possible_cpus->cpus;
^
hw/core/numa.c:69:17: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
uint16List *cpus = NULL;
^
hw/acpi/aml-build.c:2005:20: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
CPUArchIdList *cpus = ms->possible_cpus;
^
hw/core/machine-smp.c:77:14: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
unsigned cpus = config->has_cpus ? config->cpus : 0;
^
include/hw/core/cpu.h:589:17: note: previous declaration is here
extern CPUTailQ cpus;
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20231010115048.11856-2-philmd@linaro.org>
Following the example documented since commit e3fe3988d7 ("error:
Document Error API usage rules"), have cpu_exec_realizefn()
return a boolean indicating whether an error is set or not.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230918160257.30127-22-philmd@linaro.org>
Let CPUClass::class_by_name() handlers to return abstract classes,
and filter them once in the public cpu_class_by_name() method.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230908112235.75914-3-philmd@linaro.org>
"hw/s390x/sclp.h" is a header used by target-agnostic objects
(such hw/char/sclpconsole[-lm].c), thus can not use target-specific
types, such CPUS390XState.
Have sclp_service_call[_protected]() take a S390CPU pointer, which
is target-agnostic.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231106114500.5269-3-philmd@linaro.org>
"hw/s390x/css.h" is a header used by target-agnostic objects
(such hw/s390x/virtio-ccw-gpu.c), thus can not use target-specific
types, such CPUS390XState.
Have css_do_sic() take S390CPU a pointer, which is target-agnostic.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20231106114500.5269-2-philmd@linaro.org>
The OBJECT_DECLARE_CPU_TYPE() macro forward-declares the
PowerPCCPUClass type. This forward declaration is sufficient
for code in hw/ to use the QOM definitions. No need to expose
the structure definition. Keep it local to target/ppc/ by
moving it to target/ppc/cpu.h.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231013125630.95116-5-philmd@linaro.org>
Introduce cpu_exec_reset_hold() which call an accelerator
specific AccelOpsClass::cpu_reset_hold() handler.
Define a stub on TCG user emulation, because CPU reset is
irrelevant there.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230918104153.24433-3-philmd@linaro.org>
virtio sound card support
vhost-user: back-end state migration
cxl:
line length reduction
enabling fabric management
vhost-vdpa:
shadow virtqueue hash calculation Support
shadow virtqueue RSS Support
tests:
CPU topology related smbios test cases
Fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmVKDDoPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpF08H/0Zts8uvkHbgiOEJw4JMHU6/VaCipfIYsp01
GSfwYOyEsXJ7GIxKWaCiMnWXEm7tebNCPKf3DoUtcAojQj3vuF9XbWBKw/bfRn83
nGO/iiwbYViSKxkwqUI+Up5YiN9o0M8gBFrY0kScPezbnYmo5u2bcADdEEq6gH68
D0Ea8i+WmszL891ypvgCDBL2ObDk3qX3vA5Q6J2I+HKX2ofJM59BwaKwS5ghw+IG
BmbKXUZJNjUQfN9dQ7vJuiuqdknJ2xUzwW2Vn612ffarbOZB1DZ6ruWlrHty5TjX
0w4IXEJPBgZYbX9oc6zvTQnbLDBJbDU89mnme0TcmNMKWmQKTtc=
=vEv+
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, fixes
virtio sound card support
vhost-user: back-end state migration
cxl:
line length reduction
enabling fabric management
vhost-vdpa:
shadow virtqueue hash calculation Support
shadow virtqueue RSS Support
tests:
CPU topology related smbios test cases
Fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmVKDDoPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpF08H/0Zts8uvkHbgiOEJw4JMHU6/VaCipfIYsp01
# GSfwYOyEsXJ7GIxKWaCiMnWXEm7tebNCPKf3DoUtcAojQj3vuF9XbWBKw/bfRn83
# nGO/iiwbYViSKxkwqUI+Up5YiN9o0M8gBFrY0kScPezbnYmo5u2bcADdEEq6gH68
# D0Ea8i+WmszL891ypvgCDBL2ObDk3qX3vA5Q6J2I+HKX2ofJM59BwaKwS5ghw+IG
# BmbKXUZJNjUQfN9dQ7vJuiuqdknJ2xUzwW2Vn612ffarbOZB1DZ6ruWlrHty5TjX
# 0w4IXEJPBgZYbX9oc6zvTQnbLDBJbDU89mnme0TcmNMKWmQKTtc=
# =vEv+
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 07 Nov 2023 18:06:50 HKT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (63 commits)
acpi/tests/avocado/bits: enable console logging from bits VM
acpi/tests/avocado/bits: enforce 32-bit SMBIOS entry point
hw/cxl: Add tunneled command support to mailbox for switch cci.
hw/cxl: Add dummy security state get
hw/cxl/type3: Cleanup multiple CXL_TYPE3() calls in read/write functions
hw/cxl/mbox: Add Get Background Operation Status Command
hw/cxl: Add support for device sanitation
hw/cxl/mbox: Wire up interrupts for background completion
hw/cxl/mbox: Add support for background operations
hw/cxl: Implement Physical Ports status retrieval
hw/pci-bridge/cxl_downstream: Set default link width and link speed
hw/cxl/mbox: Add Physical Switch Identify command.
hw/cxl/mbox: Add Information and Status / Identify command
hw/cxl: Add a switch mailbox CCI function
hw/pci-bridge/cxl_upstream: Move defintion of device to header.
hw/cxl/mbox: Generalize the CCI command processing
hw/cxl/mbox: Pull the CCI definition out of the CXLDeviceState
hw/cxl/mbox: Split mailbox command payload into separate input and output
hw/cxl/mbox: Pull the payload out of struct cxl_cmd and make instances constant
hw/cxl: Fix a QEMU_BUILD_BUG_ON() in switch statement scope issue.
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add Xen PV console and network support, the former of which enables the
Xen "PV shim" to be used to support PV guests.
Also clean up the block support and make it work when the user passes
just 'drive file=IMAGE,if=xen' on the command line.
Update the documentation to reflect all of these, taking the opportunity
to simplify what it says about q35 by making unplug work for AHCI.
Ignore the VCPU_SSHOTTMR_future timer flag, and advertise the 'fixed'
per-vCPU upcall vector support, as newer upstream Xen do.
-----BEGIN PGP SIGNATURE-----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=Dg79
-----END PGP SIGNATURE-----
Merge tag 'pull-xenfv.for-upstream-20231107' of git://git.infradead.org/users/dwmw2/qemu into staging
Xen PV guest support for 8.2
Add Xen PV console and network support, the former of which enables the
Xen "PV shim" to be used to support PV guests.
Also clean up the block support and make it work when the user passes
just 'drive file=IMAGE,if=xen' on the command line.
Update the documentation to reflect all of these, taking the opportunity
to simplify what it says about q35 by making unplug work for AHCI.
Ignore the VCPU_SSHOTTMR_future timer flag, and advertise the 'fixed'
per-vCPU upcall vector support, as newer upstream Xen do.
# -----BEGIN PGP SIGNATURE-----
#
# iQJIBAABCAAyFiEEvgfZ/VSAmrLEsP9fY3Ys2mfi81kFAmVJ/7EUHGR3bXcyQGlu
# ZnJhZGVhZC5vcmcACgkQY3Ys2mfi81k+/xAAswivVR4+nwz3wTSN7EboGogS3hy+
# ZsTpvbJnfprGQJAK8vv8OP4eunaCJkO/dy3M/33Dh270msmV6I/1ki0E1RIPG45D
# n5wKM1Zxk0ABvjIgdp3xiLwITTdruJ+k9aqV8U9quhjgNFdOa7yjBOG8MD32GEPZ
# KHbavJ++huOu7+DZHJRNRq4gI/fREIULoPGHVg7WuEiRDYokOOmMROXqmTHTaUkV
# yFhkofzWxlpYhh7qRQx6/A80CSf7xwCof8krjdMCOYj3XGzYVZND0z5ZfHQYEwqt
# fowhargA8gH4V3d21S/MWCaZ+QrswFXZhcnl5wuGgWakV4ChvFETKs+fz2mODWUx
# 2T13trqeFJ5ElTrSpH1iWCoSEy6KCeLecvx7c/6HPSkDYQ3w5q8dXPpqgEtXY24S
# Wcmw4PkQ+HrLX7wbSU7QLyTZjvCQLFZ3Sb0uTf2zwsJZyeCCiT2lqAaogoMm6Kg0
# m/jG1JzE+9AC3j0Upp1lS3EK1qdxIuLdBuIcaEBEjy7Am+Y14PlZYoU2c751KbRF
# kqnIOYMoijX0PJDomPqCQtYNE0mrtogo0AbcFFIu+4k25vGbkl7xS5p2du9qw2Rd
# ++IdqQYzdzrUcIwmxocFQqFBJQ2dcbOGB1d7+VJ+A1Uj3yY2/DnFG5WqSaqS0KJi
# ZhBdFs3OTlPnRoM=
# =Dg79
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 07 Nov 2023 17:13:21 HKT
# gpg: using RSA key BE07D9FD54809AB2C4B0FF5F63762CDA67E2F359
# gpg: issuer "dwmw2@infradead.org"
# gpg: Good signature from "David Woodhouse <dwmw2@infradead.org>" [unknown]
# gpg: aka "David Woodhouse <dwmw2@exim.org>" [unknown]
# gpg: aka "David Woodhouse <david@woodhou.se>" [unknown]
# gpg: aka "David Woodhouse <dwmw2@kernel.org>" [unknown]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: BE07 D9FD 5480 9AB2 C4B0 FF5F 6376 2CDA 67E2 F359
* tag 'pull-xenfv.for-upstream-20231107' of git://git.infradead.org/users/dwmw2/qemu:
docs: update Xen-on-KVM documentation
xen-platform: unplug AHCI disks
hw/i386/pc: support '-nic' for xen-net-device
hw/xen: update Xen PV NIC to XenDevice model
hw/xen: only remove peers of PCI NICs on unplug
hw/xen: add support for Xen primary console in emulated mode
hw/xen: update Xen console to XenDevice model
hw/xen: do not repeatedly try to create a failing backend device
hw/xen: add get_frontend_path() method to XenDeviceClass
hw/xen: automatically assign device index to block devices
hw/xen: populate store frontend nodes with XenStore PFN/port
i386/xen: advertise XEN_HVM_CPUID_UPCALL_VECTOR in CPUID
include: update Xen public headers to Xen 4.17.2 release
hw/xen: Clean up event channel 'type_val' handling to use union
i386/xen: Ignore VCPU_SSHOTTMR_future flag in set_singleshot_timer()
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The default NIC creation seems a bit hackish to me. I don't understand
why each platform has to call pci_nic_init_nofail() from a point in the
code where it actually has a pointer to the PCI bus, and then we have
the special cases for things like ne2k_isa.
If qmp_device_add() can *find* the appropriate bus and instantiate
the device on it, why can't we just do that from generic code for
creating the default NICs too?
But that isn't a yak I want to shave today. Add a xenbus field to the
PCMachineState so that it can make its way from pc_basic_device_init()
to pc_nic_init() and be handled as a special case like ne2k_isa is.
Now we can launch emulated Xen guests with '-nic user'.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The primary console is special because the toolstack maps a page into
the guest for its ring, and also allocates the guest-side event channel.
The guest's grant table is even primed to export that page using a known
grant ref#. Add support for all that in emulated mode, so that we can
have a primary console.
For reasons unclear, the backends running under real Xen don't just use
a mapping of the well-known GNTTAB_RESERVED_CONSOLE grant ref (which
would also be in the ring-ref node in XenStore). Instead, the toolstack
sets the ring-ref node of the primary console to the GFN of the guest
page. The backend is expected to handle that special case and map it
with foreignmem operations instead.
We don't have an implementation of foreignmem ops for emulated Xen mode,
so just make it map GNTTAB_RESERVED_CONSOLE instead. This would probably
work for real Xen too, but we can't work out how to make real Xen create
a primary console of type "ioemu" to make QEMU drive it, so we can't
test that; might as well leave it as it is for now under Xen.
Now at last we can boot the Xen PV shim and run PV kernels in QEMU.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
If xen_backend_device_create() fails to instantiate a device, the XenBus
code will just keep trying over and over again each time the bus is
re-enumerated, as long as the backend appears online and in
XenbusStateInitialising.
The only thing which prevents the XenBus code from recreating duplicates
of devices which already exist, is the fact that xen_device_realize()
sets the backend state to XenbusStateInitWait. If the attempt to create
the device doesn't get *that* far, that's when it will keep getting
retried.
My first thought was to handle errors by setting the backend state to
XenbusStateClosed, but that doesn't work for XenConsole which wants to
*ignore* any device of type != "ioemu" completely.
So, make xen_backend_device_create() *keep* the XenBackendInstance for a
failed device, and provide a new xen_backend_exists() function to allow
xen_bus_type_enumerate() to check whether one already exists before
creating a new one.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The primary Xen console is special. The guest's side is set up for it by
the toolstack automatically and not by the standard PV init sequence.
Accordingly, its *frontend* doesn't appear in …/device/console/0 either;
instead it appears under …/console in the guest's XenStore node.
To allow the Xen console driver to override the frontend path for the
primary console, add a method to the XenDeviceClass which can be used
instead of the standard xen_device_get_frontend_path()
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
There's no need to force the user to assign a vdev. We can automatically
assign one, starting at xvda and searching until we find the first disk
name that's unused.
This means we can now allow '-drive if=xen,file=xxx' to work without an
explicit separate -driver argument, just like if=virtio.
Rip out the legacy handling from the xenpv machine, which was scribbling
over any disks configured by the toolstack, and didn't work with anything
but raw images.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
... in order to advertise the XEN_HVM_CPUID_UPCALL_VECTOR feature,
which will come in a subsequent commit.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Paul Durrant <paul@xen.org>
This implementation of tunneling makes the choice that our Type 3 device is
a Logical Device (LD) of a Multi-Logical Device (MLD) that just happens to
only have one LD for now.
Tunneling is supported from a Switch Mailbox CCI (and shortly via MCTP over
I2C connected to the switch MCTP CCI) via an outer level to the FM owned LD
in the MLD Type 3 device. From there an inner tunnel may be used to access
particular LDs.
Protocol wise, the following is what happens in a real system but we
don't emulate the transports - just the destinations and the payloads.
( Host -> Switch Mailbox CCI - in band FM-API mailbox command
or
Host -> Switch MCTP CCI - MCTP over I2C using the CXL FM-API
MCTP Binding.
)
then (if a tunnel command)
Switch -> Type 3 FM Owned LD - MCTP over PCI VDM using the
CXL FM-API binding (addressed by switch port)
then (if unwrapped command also a tunnel command)
Type 3 FM Owned LD to LD0 via internal transport
(addressed by LD number)
or (added shortly)
Host to Type 3 FM Owned MCTP CCI - MCTP over I2C using the
CXL FM-API MCTP Binding.
then (if unwrapped comand is a tunnel comamnd)
Type 3 FM Owned LD to LD0 via internal transport.
(addressed by LD number)
It is worth noting that the tunneling commands over PCI VDM
presumably use the appropriate MCTP binding depending on opcode.
This may be the CXL FMAPI binding or the CXL Memory Device Binding.
Additional commands will need to be added to make this
useful beyond testing the tunneling works.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-18-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make use of the background operations through the sanitize command, per CXL
3.0 specs. Traditionally run times can be rather long, depending on the
size of the media.
Estimate times based on:
https://pmem.io/documents/NVDIMM_DSM_Interface-V1.8.pdf
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-14-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Notify when the background operation is done. Note that for now background
commands are only supported on the main Type 3 mailbox.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-13-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support background commands in the mailbox, and update
cmd_infostat_bg_op_sts() accordingly. This patch does not implement mbox
interrupts upon completion, so the kernel driver must rely on polling to
know when the operation is done.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-12-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable it for the switch CCI.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL switch CCIs were added in CXL r3.0. They are a PCI function,
identified by class code that provides a CXL mailbox (identical
to that previously defined for CXL type 3 memory devices) over which
various FM-API commands may be used. Whilst the intent of this
feature is enable switch control from a BMC attached to a switch
upstream port, it is also useful to allow emulation of this feature
on the upstream port connected to a host using the CXL devices as
this greatly simplifies testing.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid repetition of switch upstream port specific data in the
CXLDeviceState structure it will be necessary to access the switch USP
specific data from mailbox callbacks. Hence move it to cxl_device.h so it
is no longer an opaque structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023160806.13206-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By moving the parts of the mailbox command handling that are CCI type
specific out to the caller, make the main handling code generic. Rename it
to cxl_process_cci_message() to reflect this new generality.
Change the type3 mailbox handling (reused shortly for the switch
mailbox CCI) to take a snapshot of the mailbox input data rather
than operating on it in place. This reduces the chance of bugs
due to aliasing going forwars.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enables having multiple CCIs per devices. Each CCI (mailbox) has it's own
state and command list, so they can't share a single structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
New CCI types that will be supported shortly do not have a single buffer
used in both directions. As such, split it up. To avoid the complexities
of implementing all commands to handle potential aliasing, take a copy of
the input before use.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Putting the pointer in the structure for command handling puts a single
variable element inside an otherwise constant structure. Move it out as
a directly passed variable and take the cxl_cmd structures constant.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023160806.13206-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Michael Tsirkin observed that there were some unnecessarily
long lines in the CXL code in a recent review.
This patch is intended to rectify that where it does not
hurt readability.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Done to reduce line lengths where this is used.
Ext seems sufficiently obvious that it need not be spelt out
fully.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Handle output IO messages in the transmit (TX) virtqueue.
It allocates a VirtIOSoundPCMBuffer for each IO message and copies the
data buffer to it. When the IO buffer is written to the host's sound
card, the guest will be notified that it has been consumed.
The lifetime of an IO message is:
1. Guest sends IO message to TX virtqueue.
2. QEMU adds it to the appropriate stream's IO buffer queue.
3. Sometime later, the host audio backend calls the output callback,
virtio_snd_pcm_out_cb(), which is defined with an AUD_open_out()
call. The callback gets an available number of bytes the backend can
receive. Then it writes data from the IO buffer queue to the backend.
If at any time a buffer is exhausted, it is returned to the guest as
completed.
4. If the guest releases the stream, its buffer queue is flushed by
attempting to write any leftover data to the audio backend and
releasing all IO messages back to the guest. This is how according to
the spec the guest knows the release was successful.
Based-on: 5a2f350eec
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Anton Yakovlev <Anton.Yakovlev@opensynergy.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <b7c6fc458c763d09a4abbcb620ae9b220afa5b8f.1698062525.git.manos.pitsidianakis@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Receive guest requests in the control (CTRL) queue of the virtio sound
device and reply with a NOT SUPPORTED error to all control commands.
The receiving handler is virtio_snd_handle_ctrl(). It stores all control
messages in the queue in the device's command queue. Then it calls
virtio_snd_process_cmdq() to handle each message.
The handler is process_cmd() which replies with VIRTIO_SND_S_NOT_SUPP.
Based-on: 5a2f350eec
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Anton Yakovlev <Anton.Yakovlev@opensynergy.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <3224aff87e7c4f2777bfe1bbbbca93b72525992c.1698062525.git.manos.pitsidianakis@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a new VIRTIO device for the virtio sound device id. Functionality
will be added in the following commits.
Based-on: 5a2f350eec
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Anton Yakovlev <Anton.Yakovlev@opensynergy.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <f9678a41fe97b5886c1b04795f1be046509de866.1698062525.git.manos.pitsidianakis@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_save_backend_state() and vhost_load_backend_state() can be used by
vhost front-ends to easily save and load the back-end's state to/from
the migration stream.
Because we do not know the full state size ahead of time,
vhost_save_backend_state() simply reads the data in 1 MB chunks, and
writes each chunk consecutively into the migration stream, prefixed by
its length. EOF is indicated by a 0-length chunk.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-Id: <20231016134243.68248-7-hreitz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the interface for transferring the back-end's state during migration
as defined previously in vhost-user.rst.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-Id: <20231016134243.68248-6-hreitz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/hppa: Map astro chip 64-bit I/O mem
hw/hppa: Turn on 64-bit cpu for C3700
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmVJqDEdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV8n5Qf/R15CvXGMgjDJjoV2
ILMFM+Rpg17SR2yu060sEZ01R3iHdobeCcDB184K0RI9JLrpcBFar+PeF023o9fn
O9MnfIyL6/ggzaeIpQ9AD2uT0HJMU9hLFoyQqQvnhDHHcT34raL2+Zkrkb2vvauH
XET7awXN9xYCnY4ALrfcapzlrHqI77ahz0vReUWPxk7eGY2ez8dEOiFW2WLBmuMx
mAFAMrFQhq66GjoMDl8JiGHD/KBJQ9X4eUAEotS27lTCOYU0ryA6dWBGqBSTWCUa
smpxkeGQKOew+717HV1H4FdCRYG1Rgm7yFN423JULeew+T7DHvfe0K55vMIulx5I
g3oVZA==
=dxC7
-----END PGP SIGNATURE-----
Merge tag 'pull-pa-20231106' of https://gitlab.com/rth7680/qemu into staging
target/hppa: Implement PA2.0 instructions
hw/hppa: Map astro chip 64-bit I/O mem
hw/hppa: Turn on 64-bit cpu for C3700
# -----BEGIN PGP SIGNATURE-----
#
# iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmVJqDEdHHJpY2hhcmQu
# aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV8n5Qf/R15CvXGMgjDJjoV2
# ILMFM+Rpg17SR2yu060sEZ01R3iHdobeCcDB184K0RI9JLrpcBFar+PeF023o9fn
# O9MnfIyL6/ggzaeIpQ9AD2uT0HJMU9hLFoyQqQvnhDHHcT34raL2+Zkrkb2vvauH
# XET7awXN9xYCnY4ALrfcapzlrHqI77ahz0vReUWPxk7eGY2ez8dEOiFW2WLBmuMx
# mAFAMrFQhq66GjoMDl8JiGHD/KBJQ9X4eUAEotS27lTCOYU0ryA6dWBGqBSTWCUa
# smpxkeGQKOew+717HV1H4FdCRYG1Rgm7yFN423JULeew+T7DHvfe0K55vMIulx5I
# g3oVZA==
# =dxC7
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 07 Nov 2023 11:00:01 HKT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* tag 'pull-pa-20231106' of https://gitlab.com/rth7680/qemu: (85 commits)
hw/hppa: Allow C3700 with 64-bit and B160L with 32-bit CPU only
hw/hppa: Turn on 64-bit CPU for C3700 machine
hw/pci-host/astro: Trigger CPU irq on CPU HPA in high memory
hw/pci-host/astro: Map Astro chip into 64-bit I/O memory region
target/hppa: Improve interrupt logging
target/hppa: Update IIAOQ, IIASQ for pa2.0
target/hppa: Create raise_exception_with_ior
target/hppa: Add unwind_breg to CPUHPPAState
target/hppa: Clear upper bits in mtctl for pa1.x
target/hppa: Avoid async_safe_run_on_cpu on uniprocessor system
target/hppa: Add pa2.0 cpu local tlb flushes
target/hppa: Implement pa2.0 data prefetch instructions
linux-user/hppa: Drop EXCP_DUMP from handled exceptions
hw/hppa: Translate phys addresses for the cpu
include/hw/elf: Remove truncating signed casts
target/hppa: Return zero for r0 from load_gpr
target/hppa: Precompute zero into DisasContext
target/hppa: Fix interruption based on default PSW
target/hppa: Implement PERMH
target/hppa: Implement MIXH, MIXW
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There's nothing about elf that specifically requires signed vs unsigned.
This is very much a target-specific preference.
In the meantime, casting low and high from uint64_t back to Elf_SWord
to uint64_t discards high bits that might have been set by translate_fn.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Support for non 64b IOVA space
* Introduction of a PCIIOMMUOps callback structure to ease future
extensions
* Fix for a buffer overrun when writing the VF token
* PPC cleanups preparing ground for IOMMUFD support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmVI+bIACgkQUaNDx8/7
7KHW4g/9FmgX0k2Elm1BAul3slJtuBT8/iHKfK19rhXICxhxS5xBWJA8FmosTWAT
91YqQJhOHARxLd9VROfv8Fq8sAo+Ys8bP3PTXh5satjY5gR9YtmMSVqvsAVLn7lv
a/0xp7wPJt2UeKzvRNUqFXNr7yHPwxFxbJbmmAJbNte8p+TfE2qvojbJnu7BjJbg
sTtS/vFWNJwtuNYTkMRoiZaUKEoEZ8LnslOqKUjgeO59g4i3Dq8e2JCmHANPFWUK
cWmr7AqcXgXEnLSDWTtfN53bjcSCYkFVb4WV4Wv1/7hUF5jQ4UR0l3B64xWe0M3/
Prak3bWOM/o7JwLBsgaWPngXA9V0WFBTXVF4x5qTwhuR1sSV8MxUvTKxI+qqiEzA
FjU89oSZ+zXId/hEUuTL6vn1Th8/6mwD0L9ORchNOQUKzCjBzI4MVPB09nM3AdPC
LGThlufsZktdoU2KjMHpc+gMIXQYsxkgvm07K5iZTZ5eJ4tV5KB0aPvTZppGUxe1
YY9og9F3hxjDHQtEuSY2rzBQI7nrUpd1ZI5ut/3ZgDWkqD6aGRtMme4n4GsGsYb2
Ht9+d2RL9S8uPUh+7rV8K/N3+vXgXRaEYTuAScKtflEbA7YnZA5nUdMng8x0kMTQ
Y73XCd4UGWDfSSZsgaIHGkM/MRIHgmlrfcwPkWqWW9vF+92O6Hw=
=/Du0
-----END PGP SIGNATURE-----
Merge tag 'pull-vfio-20231106' of https://github.com/legoater/qemu into staging
vfio queue:
* Support for non 64b IOVA space
* Introduction of a PCIIOMMUOps callback structure to ease future
extensions
* Fix for a buffer overrun when writing the VF token
* PPC cleanups preparing ground for IOMMUFD support
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmVI+bIACgkQUaNDx8/7
# 7KHW4g/9FmgX0k2Elm1BAul3slJtuBT8/iHKfK19rhXICxhxS5xBWJA8FmosTWAT
# 91YqQJhOHARxLd9VROfv8Fq8sAo+Ys8bP3PTXh5satjY5gR9YtmMSVqvsAVLn7lv
# a/0xp7wPJt2UeKzvRNUqFXNr7yHPwxFxbJbmmAJbNte8p+TfE2qvojbJnu7BjJbg
# sTtS/vFWNJwtuNYTkMRoiZaUKEoEZ8LnslOqKUjgeO59g4i3Dq8e2JCmHANPFWUK
# cWmr7AqcXgXEnLSDWTtfN53bjcSCYkFVb4WV4Wv1/7hUF5jQ4UR0l3B64xWe0M3/
# Prak3bWOM/o7JwLBsgaWPngXA9V0WFBTXVF4x5qTwhuR1sSV8MxUvTKxI+qqiEzA
# FjU89oSZ+zXId/hEUuTL6vn1Th8/6mwD0L9ORchNOQUKzCjBzI4MVPB09nM3AdPC
# LGThlufsZktdoU2KjMHpc+gMIXQYsxkgvm07K5iZTZ5eJ4tV5KB0aPvTZppGUxe1
# YY9og9F3hxjDHQtEuSY2rzBQI7nrUpd1ZI5ut/3ZgDWkqD6aGRtMme4n4GsGsYb2
# Ht9+d2RL9S8uPUh+7rV8K/N3+vXgXRaEYTuAScKtflEbA7YnZA5nUdMng8x0kMTQ
# Y73XCd4UGWDfSSZsgaIHGkM/MRIHgmlrfcwPkWqWW9vF+92O6Hw=
# =/Du0
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 06 Nov 2023 22:35:30 HKT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-vfio-20231106' of https://github.com/legoater/qemu: (22 commits)
vfio/common: Move vfio_host_win_add/del into spapr.c
vfio/spapr: Make vfio_spapr_create/remove_window static
vfio/container: Move spapr specific init/deinit into spapr.c
vfio/container: Move vfio_container_add/del_section_window into spapr.c
vfio/container: Move IBM EEH related functions into spapr_pci_vfio.c
util/uuid: Define UUID_STR_LEN from UUID_NONE string
util/uuid: Remove UUID_FMT_LEN
vfio/pci: Fix buffer overrun when writing the VF token
util/uuid: Add UUID_STR_LEN definition
hw/pci: modify pci_setup_iommu() to set PCIIOMMUOps
test: Add some tests for range and resv-mem helpers
virtio-iommu: Consolidate host reserved regions and property set ones
virtio-iommu: Implement set_iova_ranges() callback
virtio-iommu: Record whether a probe request has been issued
range: Introduce range_inverse_array()
virtio-iommu: Introduce per IOMMUDevice reserved regions
util/reserved-region: Add new ReservedRegion helpers
range: Make range_compare() public
virtio-iommu: Rename reserved_regions into prop_resv_regions
vfio: Collect container iova range info
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This driver is like virtio-balloon on steroids: it allows both changing the
guest memory allocation via ballooning and (in the next patch) inserting
pieces of extra RAM into it on demand from a provided memory backend.
The actual resizing is done via ballooning interface (for example, via
the "balloon" HMP command).
This includes resizing the guest past its boot size - that is, hot-adding
additional memory in granularity limited only by the guest alignment
requirements, as provided by the next patch.
In contrast with ACPI DIMM hotplug where one can only request to unplug a
whole DIMM stick this driver allows removing memory from guest in single
page (4k) units via ballooning.
After a VM reboot the guest is back to its original (boot) size.
In the future, the guest boot memory size might be changed on reboot
instead, taking into account the effective size that VM had before that
reboot (much like Hyper-V does).
For performance reasons, the guest-released memory is tracked in a few
range trees, as a series of (start, count) ranges.
Each time a new page range is inserted into such tree its neighbors are
checked as candidates for possible merging with it.
Besides performance reasons, the Dynamic Memory protocol itself uses page
ranges as the data structure in its messages, so relevant pages need to be
merged into such ranges anyway.
One has to be careful when tracking the guest-released pages, since the
guest can maliciously report returning pages outside its current address
space, which later clash with the address range of newly added memory.
Similarly, the guest can report freeing the same page twice.
The above design results in much better ballooning performance than when
using virtio-balloon with the same guest: 230 GB / minute with this driver
versus 70 GB / minute with virtio-balloon.
During a ballooning operation most of time is spent waiting for the guest
to come up with newly freed page ranges, processing the received ranges on
the host side (in QEMU and KVM) is nearly instantaneous.
The unballoon operation is also pretty much instantaneous:
thanks to the merging of the ballooned out page ranges 200 GB of memory can
be returned to the guest in about 1 second.
With virtio-balloon this operation takes about 2.5 minutes.
These tests were done against a Windows Server 2019 guest running on a
Xeon E5-2699, after dirtying the whole memory inside guest before each
balloon operation.
Using a range tree instead of a bitmap to track the removed memory also
means that the solution scales well with the guest size: even a 1 TB range
takes just a few bytes of such metadata.
Since the required GTree operations aren't present in every Glib version
a check for them was added to the meson build script, together with new
"--enable-hv-balloon" and "--disable-hv-balloon" configure arguments.
If these GTree operations are missing in the system's Glib version this
driver will be skipped during QEMU build.
An optional "status-report=on" device parameter requests memory status
events from the guest (typically sent every second), which allow the host
to learn both the guest memory available and the guest memory in use
counts.
Following commits will add support for their external emission as
"HV_BALLOON_STATUS_REPORT" QMP events.
The driver is named hv-balloon since the Linux kernel client driver for
the Dynamic Memory Protocol is named as such and to follow the naming
pattern established by the virtio-balloon driver.
The whole protocol runs over Hyper-V VMBus.
The driver was tested against Windows Server 2012 R2, Windows Server 2016
and Windows Server 2019 guests and obeys the guest alignment requirements
reported to the host via DM_CAPABILITIES_REPORT message.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
This commit adds Hyper-V Dynamic Memory Protocol definitions, taken
from hv_balloon Linux kernel driver, adapted to the QEMU coding style and
definitions.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Only spapr supports a customed host window list, other vfio driver
assume 64bit host window. So remove the check in listener callback
and move vfio_host_win_add/del into spapr.c and make it static.
With the check removed, we still need to do the same check for
VFIO_SPAPR_TCE_IOMMU which allows a single host window range
[dma32_window_start, dma32_window_size). Move vfio_find_hostwin
into spapr.c and do same check in vfio_container_add_section_window
instead.
When mapping a ram device section, if it's unaligned with
hostwin->iova_pgsizes, this mapping is bypassed. With hostwin
moved into spapr, we changed to check container->pgsizes.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
vfio_spapr_create_window calls vfio_spapr_remove_window,
With reoder of definition of the two, we can make
vfio_spapr_create/remove_window static.
No functional changes intended.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move spapr specific init/deinit code into spapr.c and wrap
them with vfio_spapr_container_init/deinit, this way footprint
of spapr is further reduced, vfio_prereg_listener could also
be made static.
vfio_listener_release is unnecessary when prereg_listener is
moved out, so have it removed.
No functional changes intended.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
With vfio_eeh_as_ok/vfio_eeh_as_op moved and made static,
vfio.h becomes empty and is deleted.
No functional changes intended.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Acked-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Let's support empty memory devices -- memory devices that don't have a
memory device region in the current configuration. hv-balloon with an
optional memdev is the primary use case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
This patch modifies pci_setup_iommu() to set PCIIOMMUOps
instead of setting PCIIOMMUFunc. PCIIOMMUFunc is used to
get an address space for a PCI device in vendor specific
way. The PCIIOMMUOps still offers this functionality. But
using PCIIOMMUOps leaves space to add more iommu related
vendor specific operations.
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Yi Sun <yi.y.sun@linux.intel.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hervé Poussineau <hpoussin@reactos.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Cc: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Cc: Jagannathan Raman <jag.raman@oracle.com>
Cc: Matthew Rosato <mjrosato@linux.ibm.com>
Cc: Eric Farman <farman@linux.ibm.com>
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Helge Deller <deller@gmx.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
[ clg: - refreshed on latest QEMU
- included hw/remote/iommu.c
- documentation update
- asserts in pci_setup_iommu()
- removed checks on iommu_bus->iommu_ops->get_address_space
- included Elroy PCI host (PA-RISC) ]
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The implementation populates the array of per IOMMUDevice
host reserved ranges.
It is forbidden to have conflicting sets of host IOVA ranges
to be applied onto the same IOMMU MR (implied by different
host devices).
In case the callback is called after the probe request has
been issues by the driver, a warning is issued.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: "Michael S. Tsirkin" <mst@redhat.com>
Tested-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Add an IOMMUDevice 'probe_done' flag to record that the driver
already issued a probe request on that device.
This will be useful to double check host reserved regions aren't
notified after the probe and hence are not taken into account
by the driver.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: "Michael S. Tsirkin" <mst@redhat.com>
Tested-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
For the time being the per device reserved regions are
just a duplicate of IOMMU wide reserved regions. Subsequent
patches will combine those with host reserved regions, if any.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Yanghang Liu <yanghliu@redhat.com>
Reviewed-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Rename VirtIOIOMMU (nb_)reserved_regions fields with the "prop_" prefix
to highlight those fields are set through a property, at machine level.
They are IOMMU wide.
A subsequent patch will introduce per IOMMUDevice reserved regions
that will include both those IOMMU wide property reserved
regions plus, sometimes, host reserved regions, if the device is
backed by a host device protected by a physical IOMMU. Also change
nb_ prefix by nr_.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Collect iova range information if VFIO_IOMMU_TYPE1_INFO_CAP_IOVA_RANGE
capability is supported.
This allows to propagate the information though the IOMMU MR
set_iova_ranges() callback so that virtual IOMMUs
get aware of those aperture constraints. This is only done if
the info is available and the number of iova ranges is greater than
0.
A new vfio_get_info_iova_range helper is introduced matching
the coding style of existing vfio_get_info_dma_avail. The
boolean returned value isn't used though. Code is aligned
between both.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
* linux-user/elfload: Add missing arm64 hwcap values
* stellaris-gamepad: Convert to qdev
* docs/specs: Convert various txt docs to rST
* MAINTAINERS: Make sure that gicv3_internal.h is covered, too
* hw/arm/pxa2xx_gpio: Pass CPU using QOM link property
* hw/watchdog/wdt_imx2: Trace MMIO access and timer activity
* hw/misc/imx7_snvs: Trace MMIO access
* hw/misc/imx6_ccm: Convert DPRINTF to trace events
* hw/i2c/pm_smbus: Convert DPRINTF to trace events
* target/arm: Enable FEAT_MOPS insns in user-mode emulation
* linux-user: Report AArch64 hwcap2 fields above bit 31
* target/arm: Make FEAT_MOPS SET* insns handle Xs == XZR correctly
* target/arm: Fix SVE STR increment
* hw/char/stm32f2xx_usart: implement TX interrupts
* target/arm: Correctly propagate stage 1 BTI guarded bit in a two-stage walk
* xlnx-versal-virt: Add AMD/Xilinx TRNG device
-----BEGIN PGP SIGNATURE-----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=OgfH
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20231102' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* linux-user/elfload: Add missing arm64 hwcap values
* stellaris-gamepad: Convert to qdev
* docs/specs: Convert various txt docs to rST
* MAINTAINERS: Make sure that gicv3_internal.h is covered, too
* hw/arm/pxa2xx_gpio: Pass CPU using QOM link property
* hw/watchdog/wdt_imx2: Trace MMIO access and timer activity
* hw/misc/imx7_snvs: Trace MMIO access
* hw/misc/imx6_ccm: Convert DPRINTF to trace events
* hw/i2c/pm_smbus: Convert DPRINTF to trace events
* target/arm: Enable FEAT_MOPS insns in user-mode emulation
* linux-user: Report AArch64 hwcap2 fields above bit 31
* target/arm: Make FEAT_MOPS SET* insns handle Xs == XZR correctly
* target/arm: Fix SVE STR increment
* hw/char/stm32f2xx_usart: implement TX interrupts
* target/arm: Correctly propagate stage 1 BTI guarded bit in a two-stage walk
* xlnx-versal-virt: Add AMD/Xilinx TRNG device
* tag 'pull-target-arm-20231102' of https://git.linaro.org/people/pmaydell/qemu-arm: (33 commits)
tests/qtest: Introduce tests for AMD/Xilinx Versal TRNG device
hw/arm: xlnx-versal-virt: Add AMD/Xilinx TRNG device
hw/misc: Introduce AMD/Xilix Versal TRNG device
target/arm: Correctly propagate stage 1 BTI guarded bit in a two-stage walk
hw/char/stm32f2xx_usart: Add more definitions for CR1 register
hw/char/stm32f2xx_usart: Update IRQ when DR is written
hw/char/stm32f2xx_usart: Extract common IRQ update code to update_irq()
target/arm: Fix SVE STR increment
target/arm: Make FEAT_MOPS SET* insns handle Xs == XZR correctly
linux-user: Report AArch64 hwcap2 fields above bit 31
target/arm: Enable FEAT_MOPS insns in user-mode emulation
hw/i2c/pm_smbus: Convert DPRINTF to trace events
hw/misc/imx6_ccm: Convert DPRINTF to trace events
hw/misc/imx7_snvs: Trace MMIO access
hw/watchdog/wdt_imx2: Trace timer activity
hw/watchdog/wdt_imx2: Trace MMIO access
hw/arm/pxa2xx_gpio: Pass CPU using QOM link property
MAINTAINERS: Make sure that gicv3_internal.h is covered, too
docs/specs/vmgenid: Convert to rST
docs/specs/vmcoreinfo: Convert to rST
...
Conflicts:
hw/input/stellaris_input.c
The qdev conversion in this pull request ("stellaris-gamepad: Convert
to qdev") eliminates the vmstate_register() call that was converted to
vmstate_register_any() in the conflicting migration pull request.
vmstate_register_any() is no longer necessary now that this device has
been converted to qdev, so take this pull request's version of
stellaris_gamepad.c over the previous pull request's
stellaris_input.c (the file was renamed).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Hi
In this pull request:
- migration reboot mode (steve)
* I disabled the test because our CI don't like programs using so
much shared memory. Searching for a fix.
- test for postcopy recover (fabiano)
- MigrateAddress QAPI (het)
- better return path error handling (peter)
- traces for downtime (peter)
- vmstate_register() check for duplicates (juan)
thomas find better solutions for s390x and ipmi.
now also works on s390x
Please, apply.
-----BEGIN PGP SIGNATURE-----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=uaqL
-----END PGP SIGNATURE-----
Merge tag 'migration-20231102-pull-request' of https://gitlab.com/juan.quintela/qemu into staging
Migration Pull request (20231102)
Hi
In this pull request:
- migration reboot mode (steve)
* I disabled the test because our CI don't like programs using so
much shared memory. Searching for a fix.
- test for postcopy recover (fabiano)
- MigrateAddress QAPI (het)
- better return path error handling (peter)
- traces for downtime (peter)
- vmstate_register() check for duplicates (juan)
thomas find better solutions for s390x and ipmi.
now also works on s390x
Please, apply.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEGJn/jt6/WMzuA0uC9IfvGFhy1yMFAmVDipMACgkQ9IfvGFhy
# 1yNYnQ/9E5Cywsoqljqa/9FiKBSII2qMrmkfu6JLKqePnsh5pFZiukbudYRuJCCe
# ZTDEmD0NmKRJbDx2xRU1qx/e6gKJy+gz37KP89Buuh/WwZHPboPYtxQpGvCSiH26
# J3i+1+TgaqmkLzcO35wa8tp6gneQclWeAwKgMvdb4cm2pJEhgWRKI62ccyLzxeve
# UCzFQn60t55ETyVZGnRD4YwdTQvGKH+DPlyTuJOLR3DePuvZd8EdH+ypvB4RLAy7
# 3+CuQOxmF5LRXPbpJuAeOsudbmhhHzrO/yL7ZmsiKQTthsJv+SzC1bO94jhQrawZ
# Q7GCii5KpGq0KnRTRKZRGk6XKwxcYRduXMX3R5tXuVmDmCZsjhXzziU8yEdftph8
# 5TJdk1o0Gb043EFu81mrsQYS+9yJqe6sy6m3PTJaec54cAty5ln+c17WOvpAOaSV
# +1phe05ftuVPmQ3KWhbIR/tCmavNLwEZxpVIfyaKJx04bFbtQ9gRpRyURORX4KXc
# s4WXvNirQEohxYBnP4TPvA09xBTW3V08pk/wRDwt0YDXnLiqCltOuxD8r05K8K4B
# MkCLcWj0g7he2tBkF60oz1KSIE0oTB81um9AzLIv5F2YSYLaJM5BIcoC437MR2f4
# MOR7drR1fP5GsRu/SeU5BWvhVq3IvdOxR7G2MLNRJJvl7ZtGXDc=
# =uaqL
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 02 Nov 2023 19:40:03 HKT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'migration-20231102-pull-request' of https://gitlab.com/juan.quintela/qemu: (40 commits)
migration: modify test_multifd_tcp_none() to use new QAPI syntax.
migration: Implement MigrateChannelList to hmp migration flow.
migration: Implement MigrateChannelList to qmp migration flow.
migration: modify migration_channels_and_uri_compatible() for new QAPI syntax
migration: New migrate and migrate-incoming argument 'channels'
migration: Convert the file backend to the new QAPI syntax
migration: convert exec backend to accept MigrateAddress.
migration: convert rdma backend to accept MigrateAddress
migration: convert socket backend to accept MigrateAddress
migration: convert migration 'uri' into 'MigrateAddress'
migration: New QAPI type 'MigrateAddress'
migration: Change ram_dirty_bitmap_reload() retval to bool
tests/migration-test: Add a test for postcopy hangs during RECOVER
migration: Allow network to fail even during recovery
migration: Refactor error handling in source return path
tests/qtest: migration: add reboot mode test
cpr: reboot mode
cpr: relax vhost migration blockers
cpr: relax blockdev migration blockers
migration: per-mode blockers
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Connect the support for Versal True Random Number Generator
(TRNG) device.
Warning: unlike the TRNG component in a real device from the
Versal device familiy, the connected TRNG model is not of
cryptographic grade and is not intended for use cases when
cryptograpically strong TRNG is needed.
Signed-off-by: Tong Ho <tong.ho@amd.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20231031184611.3029156-3-tong.ho@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds a non-cryptographic grade implementation of the
model for the True Random Number Generator (TRNG) component
in AMD/Xilinx Versal device family.
This implements all 3 modes defined by the actual hardware
specs, all of which selectable by guest software at will
at anytime:
1) PRNG mode, in which the generated sequence is required to
be reproducible after reseeded by the same 384-bit value
as supplied by guest software.
2) Test mode, in which the generated sequence is required to
be reproducible ater reseeded by the same 128-bit test
seed supplied by guest software.
3) TRNG mode, in which non-reproducible sequence is generated
based on periodic reseed by a suitable entropy source.
This model is only intended for non-real world testing of
guest software, where cryptographically strong PRNG or TRNG
is not needed.
This model supports versions 1 & 2 of the device, with
default to be version 2; the 'hw-version' uint32 property
can be set to 0x0100 to override the default.
Other implemented properties:
- 'forced-prng', uint64
When set to non-zero, mode 3's entropy source is implemented
as a deterministic sequence based on the given value and other
deterministic parameters.
This option allows the emulation to test guest software using
mode 3 and to reproduce data-dependent defects.
- 'fips-fault-events', uint32, bit-mask
bit 3: Triggers the SP800-90B entropy health test fault irq
bit 1: Triggers the FIPS 140-2 continuous test fault irq
Signed-off-by: Tong Ho <tong.ho@amd.com>
Message-id: 20231031184611.3029156-2-tong.ho@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we have converted to qdev, we can use the newer
qemu_input_handler_register() API rather than the legacy
qemu_add_kbd_event_handler().
Since we only have one user, take the opportunity to convert
from scancodes to QCodes, rather than using
qemu_input_key_value_to_scancode() (which adds an 0xe0
prefix and encodes up/down indication in the scancode,
which our old handler function then had to reverse). That
lets us drop the old state field which was tracking whether
we were halfway through a two-byte scancode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231030114802.3671871-7-peter.maydell@linaro.org
Convert the hw/input/stellaris_input device to qdev.
The interface uses an array property for the board to specify the
keycodes to use, so the s->keycodes memory is now allocated by the
array-property machinery.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231030114802.3671871-6-peter.maydell@linaro.org
Instead of exposing the ugly hack of how we represent arrays in qdev (a
static "foo-len" property and after it is set, dynamically created
"foo[i]" properties) to boards, add an interface that allows setting the
whole array at once.
Once all internal users of devices with array properties have been
converted to use this function, we can change the implementation to move
away from this hack.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231030114802.3671871-4-peter.maydell@linaro.org
This source file implements a stellaris gamepad device; rename
it so that it is a closer match to the device name.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231030114802.3671871-2-peter.maydell@linaro.org
Create a mode migration parameter that can be used to select alternate
migration algorithms. The default mode is normal, representing the
current migration algorithm, and does not need to be explicitly set.
No functional change until a new mode is added, except that the mode is
shown by the 'info migrate' command.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <1698263069-406971-2-git-send-email-steven.sistare@oracle.com>
There is no point in having mcf_uart_init() demote the DeviceState
pointer and return a void one. Directly return the real typedef.
mcf_uart_init() do both init + realize: rename as mcf_uart_create().
Similarly, mcf_uart_mm_init() do init / realize / mmap: rename as
mcf_uart_create_mmap().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231019104929.16517-1-philmd@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Avoid the interrupt controller directly access the 'first_cpu'
global. Pass 'cpu' from the board code.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231024083010.12453-2-philmd@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231020130331.50048-6-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-11-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-8-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-7-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-6-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"hw/arm/boot.h" is only required on the source file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20231025065316.56817-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM array and VIC peripheral are only used by the
2400 series, remove them from the common AspeedSoCState.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The v7-A cluster is specific to the Aspeed 2600 series,
remove it from the common AspeedSoCState.
The ARM cores belong to the MP cluster, but the array
is currently used by TYPE_ASPEED2600_SOC. We'll clean
that soon, but for now keep it in Aspeed2600SoCState.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The v7-M core is specific to the Aspeed 10x0 series,
remove it from the common AspeedSoCState.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
TYPE_ASPEED2400_SOC inherits from TYPE_ASPEED_SOC.
In few commits we'll add more fields, but to keep
review process simple, don't add any yet.
TYPE_ASPEED_SOC is common to various Aspeed SoCs,
define it in aspeed_soc_common.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
TYPE_ASPEED2600_SOC inherits from TYPE_ASPEED_SOC.
In few commits we'll add more fields, but to keep
review process simple, don't add any yet.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
TYPE_ASPEED10X0_SOC inherits from TYPE_ASPEED_SOC.
In few commits we'll add more fields, but to keep
review process simple, don't add any yet.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
infrastructure for vhost-vdpa shadow work
piix south bridge rework
reconnect for vhost-user-scsi
dummy ACPI QTG DSM for cxl
tests, cleanups, fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmU06PMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpNIsH/0DlKti86VZLJ6PbNqsnKxoK2gg05TbEhPZU
pQ+RPDaCHpFBsLC5qsoMJwvaEQFe0e49ZFemw7bXRzBxgmbbNnZ9ArCIPqT+rvQd
7UBmyC+kacVyybZatq69aK2BHKFtiIRlT78d9Izgtjmp8V7oyKoz14Esh8wkE+FT
ypHUa70Addi6alNm6BVkm7bxZxi0Wrmf3THqF8ViYvufzHKl7JR5e17fKWEG0BqV
9W7AeHMnzJ7jkTvBGUw7g5EbzFn7hPLTbO4G/VW97k0puS4WRX5aIMkVhUazsRIa
zDOuXCCskUWuRapiCwY0E4g7cCaT8/JR6JjjBaTgkjJgvo5Y8Eg=
=ILek
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups
infrastructure for vhost-vdpa shadow work
piix south bridge rework
reconnect for vhost-user-scsi
dummy ACPI QTG DSM for cxl
tests, cleanups, fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmU06PMPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpNIsH/0DlKti86VZLJ6PbNqsnKxoK2gg05TbEhPZU
# pQ+RPDaCHpFBsLC5qsoMJwvaEQFe0e49ZFemw7bXRzBxgmbbNnZ9ArCIPqT+rvQd
# 7UBmyC+kacVyybZatq69aK2BHKFtiIRlT78d9Izgtjmp8V7oyKoz14Esh8wkE+FT
# ypHUa70Addi6alNm6BVkm7bxZxi0Wrmf3THqF8ViYvufzHKl7JR5e17fKWEG0BqV
# 9W7AeHMnzJ7jkTvBGUw7g5EbzFn7hPLTbO4G/VW97k0puS4WRX5aIMkVhUazsRIa
# zDOuXCCskUWuRapiCwY0E4g7cCaT8/JR6JjjBaTgkjJgvo5Y8Eg=
# =ILek
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 22 Oct 2023 02:18:43 PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (62 commits)
intel-iommu: Report interrupt remapping faults, fix return value
MAINTAINERS: Add include/hw/intc/i8259.h to the PC chip section
vhost-user: Fix protocol feature bit conflict
tests/acpi: Update DSDT.cxl with QTG DSM
hw/cxl: Add QTG _DSM support for ACPI0017 device
tests/acpi: Allow update of DSDT.cxl
hw/i386/cxl: ensure maxram is greater than ram size for calculating cxl range
vhost-user: fix lost reconnect
vhost-user-scsi: start vhost when guest kicks
vhost-user-scsi: support reconnect to backend
vhost: move and rename the conn retry times
vhost-user-common: send get_inflight_fd once
hw/i386/pc_piix: Make PIIX4 south bridge usable in PC machine
hw/isa/piix: Implement multi-process QEMU support also for PIIX4
hw/isa/piix: Resolve duplicate code regarding PCI interrupt wiring
hw/isa/piix: Reuse PIIX3's PCI interrupt triggering in PIIX4
hw/isa/piix: Rename functions to be shared for PCI interrupt triggering
hw/isa/piix: Reuse PIIX3 base class' realize method in PIIX4
hw/isa/piix: Share PIIX3's base class with PIIX4
hw/isa/piix: Harmonize names of reset control memory regions
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The VHOST_USER_PROTOCOL_F_XEN_MMAP feature bit was defined in
f21e95ee97, which has been part of qemu's 8.1.0 release. However, it
seems it was never added to qemu's code, but it is well possible that it
is already used by different front-ends outside of qemu (i.e., Xen).
VHOST_USER_PROTOCOL_F_SHARED_OBJECT in contrast was added to qemu's code
in 1609476662, but never defined in the vhost-user specification. As a
consequence, both bits were defined to be 17, which cannot work.
Regardless of whether actual code or the specification should take
precedence, F_XEN_MMAP is already part of a qemu release, while
F_SHARED_OBJECT is not. Therefore, bump the latter to take number 18
instead of 17, and add this to the specification.
Take the opportunity to add at least a little note on the
VhostUserShared structure to the specification. This structure is
referenced by the new commands introduced in 1609476662, but was not
defined.
Fixes: 1609476662
("vhost-user: add shared_object msg")
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-Id: <20231016083201.23736-1-hreitz@redhat.com>
Reviewed-by: Emmanouil Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a simple _DSM call support for the ACPI0017 device to return fake QTG
ID values of 0 and 1 in all cases. This for _DSM plumbing testing from the OS.
Following edited for readability
Device (CXLM)
{
Name (_HID, "ACPI0017") // _HID: Hardware ID
...
Method (_DSM, 4, Serialized) // _DSM: Device-Specific Method
{
If ((Arg0 == ToUUID ("f365f9a6-a7de-4071-a66a-b40c0b4f8e52")))
{
If ((Arg2 == Zero))
{
Return (Buffer (One) { 0x01 })
}
If ((Arg2 == One))
{
Return (Package (0x02)
{
One,
Package (0x02)
{
Zero,
One
}
})
}
}
}
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231012125623.21101-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the vhost-user is reconnecting to the backend, and if the vhost-user fails
at the get_features in vhost_dev_init(), then the reconnect will fail
and it will not be retriggered forever.
The reason is:
When the vhost-user fails at get_features, the vhost_dev_cleanup will be called
immediately.
vhost_dev_cleanup calls 'memset(hdev, 0, sizeof(struct vhost_dev))'.
The reconnect path is:
vhost_user_blk_event
vhost_user_async_close(.. vhost_user_blk_disconnect ..)
qemu_chr_fe_set_handlers <----- clear the notifier callback
schedule vhost_user_async_close_bh
The vhost->vdev is null, so the vhost_user_blk_disconnect will not be
called, then the event fd callback will not be reinstalled.
All vhost-user devices have this issue, including vhost-user-blk/scsi.
With this patch, if the vdev->vdev is null, the fd callback will still
be reinstalled.
Fixes: 71e076a07d ("hw/virtio: generalise CHR_EVENT_CLOSED handling")
Signed-off-by: Li Feng <fengli@smartx.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20231009044735.941655-6-fengli@smartx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the backend crashes and restarts, the device is broken.
This patch adds reconnect for vhost-user-scsi.
This patch also improves the error messages, and reports some silent errors.
Tested with spdk backend.
Signed-off-by: Li Feng <fengli@smartx.com>
Message-Id: <20231009044735.941655-4-fengli@smartx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Multiple devices need this macro, move it to a common header.
Signed-off-by: Li Feng <fengli@smartx.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20231009044735.941655-3-fengli@smartx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU's PIIX3 implementation actually models the real PIIX4, but with different
PCI IDs. Usually, guests deal just fine with it. Still, in order to provide a
more consistent illusion to guests, allow QEMU's PIIX4 implementation to be used
in the PC machine.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20231007123843.127151-30-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the PC machine, the PIT is created in board code to allow it to be
virtualized with various virtualization techniques. So explicitly disable its
creation in the PC machine via a property which defaults to enabled. Once the
PIIX implementations are consolidated this default will keep Malta working
without further ado.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20231007123843.127151-22-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the PC machine, the PIC is created in board code to allow it to be
virtualized with various virtualization techniques. So explicitly disable its
creation in the PC machine via a property which defaults to enabled. Once the
PIIX implementations are consolidated this default will keep Malta working
without further ado.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20231007123843.127151-21-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PIIX4 has its own, private PIIX4State structure. PIIX3 has almost the
same structure, provided in a public header. So reuse it and add a
cpu_intr attribute to it which is only used by PIIX4.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20231007123843.127151-19-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
TYPE_PIIX3_PCI_DEVICE was the former base class of the Xen and non-Xen variants
of the PIIX3 ISA device models. It will become the base class for the PIIX3 and
PIIX4 device models, so drop the "3" from the type names.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231007123843.127151-15-shentey@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The power management controller is an integral part of PIIX3 (function 3). So
create it as part of the south bridge.
Note that the ACPI function is optional in QEMU. This is why it gets
object_initialize_child()'ed in realize rather than in instance_init.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231007123843.127151-14-shentey@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The USB controller is an integral part of PIIX3 (function 2). So create
it as part of the south bridge.
Note that the USB function is optional in QEMU. This is why it gets
object_initialize_child()'ed in realize rather than in instance_init.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231007123843.127151-13-shentey@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The IDE controller is an integral part of PIIX3 (function 1). So create it as
part of the south bridge.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231007123843.127151-12-shentey@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
TYPE_PIIX3_DEVICE doesn't instantiate a PIC since it relies on the board to do
so. The "pic" attribute, however, suggests that there is one. Rename the
attribute to reflect that it represents ISA interrupt lines. Use the same naming
convention as in the VIA south bridges as well as in TYPE_I82378.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20231007123843.127151-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid assigning the private member of struct PIIX3State from outside which goes
against best QOM practices. Instead, implement best QOM practice by adding an
"isa-irqs" array property to TYPE_PIIX3_DEVICE and assign it in board code, i.e.
from outside.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20231007123843.127151-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PIIX_NUM_PIC_IRQS is assumed to be the same as ISA_NUM_IRQS, otherwise
inconsistencies can occur.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231007123843.127151-5-shentey@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-user-scsi has a VirtioDeviceClass->reset() function that calls
->vhost_reset_device(). The other vhost devices don't notify the vhost
device upon reset.
Stateful vhost devices may need to handle device reset in order to free
resources or prevent stale device state from interfering after reset.
Call ->vhost_device_reset() from virtio_reset() so that that vhost
devices are notified of device reset.
This patch affects behavior as follows:
- vhost-kernel: No change in behavior since ->vhost_reset_device() is
not implemented.
- vhost-user: back-ends that negotiate
VHOST_USER_PROTOCOL_F_RESET_DEVICE now receive a
VHOST_USER_DEVICE_RESET message upon device reset. Otherwise there is
no change in behavior. DPDK, SPDK, libvhost-user, and the
vhost-user-backend crate do not negotiate
VHOST_USER_PROTOCOL_F_RESET_DEVICE automatically.
- vhost-vdpa: an extra SET_STATUS 0 call is made during device reset.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20231004014532.1228637-4-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
This series adds a new PA-RISC machine emulation for the HP-PARISC
C3700 workstation.
The physical HP C3700 machine has a PA2.0 (64-bit) CPU, in contrast to
the existing emulation of a B160L workstation which is a 32-bit only
machine and where it's Dino PCI controller isn't 64-bit capable.
With the HP C3700 machine emulation (together with the emulated Astro
Memory controller and the Elroy PCI bridge) it's now possible to
enhance the hppa CPU emulation to support the 64-bit instruction set
in upcoming patches.
Helge
v4 changes:
- Fix testsuite error in astro by adding a realize() implementation
v3 changes:
based on feedback from BALATON Zoltan <balaton@eik.bme.hu>:
- apply paches in different order to bring them logically closer to each other
- update comments in lasips2
- rephrased title and commit message of MAINTAINERS patch
v2 changes:
suggestions by BALATON Zoltan <balaton@eik.bme.hu>:
- merged pci_ids and tulip patch
- dropped comments in lasips2
- mention additional cleanups in patch "Require at least SeaBIOS-hppa version 10"
suggestions by Philippe Mathieu-Daudé <philmd@linaro.org>:
- dropped static pci_bus variable
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZTGzDQAKCRD3ErUQojoP
X9psAP0cHfTuJuXMiBWhrJhfp5VV0TURvaNXjCGyK8qvfbK+zgEArg3nvKhZPvnu
jVSq6b/Ppf3eCAZIYSVIsfLITbElTQ4=
=Esj+
-----END PGP SIGNATURE-----
Merge tag 'C3700-pull-request' of https://github.com/hdeller/qemu-hppa into staging
target/hppa: Add emulation of a C3700 HP-PARISC workstation
This series adds a new PA-RISC machine emulation for the HP-PARISC
C3700 workstation.
The physical HP C3700 machine has a PA2.0 (64-bit) CPU, in contrast to
the existing emulation of a B160L workstation which is a 32-bit only
machine and where it's Dino PCI controller isn't 64-bit capable.
With the HP C3700 machine emulation (together with the emulated Astro
Memory controller and the Elroy PCI bridge) it's now possible to
enhance the hppa CPU emulation to support the 64-bit instruction set
in upcoming patches.
Helge
v4 changes:
- Fix testsuite error in astro by adding a realize() implementation
v3 changes:
based on feedback from BALATON Zoltan <balaton@eik.bme.hu>:
- apply paches in different order to bring them logically closer to each other
- update comments in lasips2
- rephrased title and commit message of MAINTAINERS patch
v2 changes:
suggestions by BALATON Zoltan <balaton@eik.bme.hu>:
- merged pci_ids and tulip patch
- dropped comments in lasips2
- mention additional cleanups in patch "Require at least SeaBIOS-hppa version 10"
suggestions by Philippe Mathieu-Daudé <philmd@linaro.org>:
- dropped static pci_bus variable
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZTGzDQAKCRD3ErUQojoP
# X9psAP0cHfTuJuXMiBWhrJhfp5VV0TURvaNXjCGyK8qvfbK+zgEArg3nvKhZPvnu
# jVSq6b/Ppf3eCAZIYSVIsfLITbElTQ4=
# =Esj+
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 19 Oct 2023 15:51:57 PDT
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* tag 'C3700-pull-request' of https://github.com/hdeller/qemu-hppa:
hw/hppa: Add new HP C3700 machine
hw/hppa: Split out machine creation
hw/hppa: Provide RTC and DebugOutputPort on CPU #0
hw/hppa: Export machine name, BTLBs, power-button address via fw_cfg
MAINTAINERS: Update HP-PARISC entries
pci-host: Wire up new Astro/Elroy PCI bridge
hw/pci-host: Add Astro system bus adapter found on PA-RISC machines
lasips2: LASI PS/2 devices are not user-createable
pci_ids/tulip: Add PCI vendor ID for HP and use it in tulip
hw/hppa: Require at least SeaBIOS-hppa version 10
target/hppa: Update to SeaBIOS-hppa version 10
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
- MAINTAINERS updates (Zoltan, Thomas)
- Fix cutils::get_relocated_path on Windows host (Akihiko)
- Housekeeping in Memory APIs (Marc-André)
- SDHCI fix for SDMA transfer (Lu, Jianxian)
- Various QOM/QDev/SysBus cleanups (Philippe)
- Constify QemuInputHandler structure (Philippe)
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmUxnKAACgkQ4+MsLN6t
wN6UPw//abFZgckpxDYow4UfMu7esvkhICBvXjqDEdX2U/PBYmef049T5RVW8oDm
NWnxRA9XydzTeToH56tU2tjXbjWKF5LcJVwrCNl6XFRdLYaR3hzejm96hX99C89J
PB/2ineeAwidBoFfgjkvz0FLRr1ePaN74YXedPSHzywG+0dAOvpNUubbsggn3i5k
1wTlgfDvL6iz8NMEOSBp6cv5D4Ix0WshkqlCac0gQ74lYSM1tk/EeRiSy2IHWQQB
4FHd9Wo9brzLQCbhbb4FapTK0POScy0LebzRWOWfLtyWS+FRBC3kxO126I67CwMb
XRS4YgBqC3U7IGsbzV+fWP01pVeJRzZ1vrv4vdiIYvqTdgNlmFbGjJUwEmPmrokt
q5UreAjMUNLMEXiY6QHFq3N5I+UMY1jslcf7K/ZwDqSlqaquAe+gbnQOAMXDYgb6
GWsBrLM2WA5E9ObbxsHdxgZqW1NxcWJpSBvjNiOV9t/jqoqpxYwHr5HAvR1xUwm+
qRKRayRpLlX/Yad4NlvJaH5jvsMrI4bnxTYWVevLvYzc07Xo3dVxW1c+P+WCdjfM
O3bLAvwO7Mw7GRiSNpU8zTbRJu/dS4NWDWZ24u606Cy7qD/qouz89JjkKVYYSFkX
vNp7YOenPf4K6pak/lC3NOLIPlYmnnCLv3RCiaO6wHi4bk1yEBU=
=9dZy
-----END PGP SIGNATURE-----
Merge tag 'hw-misc-20231019' of https://github.com/philmd/qemu into staging
Misc hardware patch queue
- MAINTAINERS updates (Zoltan, Thomas)
- Fix cutils::get_relocated_path on Windows host (Akihiko)
- Housekeeping in Memory APIs (Marc-André)
- SDHCI fix for SDMA transfer (Lu, Jianxian)
- Various QOM/QDev/SysBus cleanups (Philippe)
- Constify QemuInputHandler structure (Philippe)
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmUxnKAACgkQ4+MsLN6t
# wN6UPw//abFZgckpxDYow4UfMu7esvkhICBvXjqDEdX2U/PBYmef049T5RVW8oDm
# NWnxRA9XydzTeToH56tU2tjXbjWKF5LcJVwrCNl6XFRdLYaR3hzejm96hX99C89J
# PB/2ineeAwidBoFfgjkvz0FLRr1ePaN74YXedPSHzywG+0dAOvpNUubbsggn3i5k
# 1wTlgfDvL6iz8NMEOSBp6cv5D4Ix0WshkqlCac0gQ74lYSM1tk/EeRiSy2IHWQQB
# 4FHd9Wo9brzLQCbhbb4FapTK0POScy0LebzRWOWfLtyWS+FRBC3kxO126I67CwMb
# XRS4YgBqC3U7IGsbzV+fWP01pVeJRzZ1vrv4vdiIYvqTdgNlmFbGjJUwEmPmrokt
# q5UreAjMUNLMEXiY6QHFq3N5I+UMY1jslcf7K/ZwDqSlqaquAe+gbnQOAMXDYgb6
# GWsBrLM2WA5E9ObbxsHdxgZqW1NxcWJpSBvjNiOV9t/jqoqpxYwHr5HAvR1xUwm+
# qRKRayRpLlX/Yad4NlvJaH5jvsMrI4bnxTYWVevLvYzc07Xo3dVxW1c+P+WCdjfM
# O3bLAvwO7Mw7GRiSNpU8zTbRJu/dS4NWDWZ24u606Cy7qD/qouz89JjkKVYYSFkX
# vNp7YOenPf4K6pak/lC3NOLIPlYmnnCLv3RCiaO6wHi4bk1yEBU=
# =9dZy
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 19 Oct 2023 14:16:16 PDT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'hw-misc-20231019' of https://github.com/philmd/qemu: (46 commits)
ui/input: Constify QemuInputHandler structure
hw/net: Declare link using static DEFINE_PROP_LINK() macro
hw/dma: Declare link using static DEFINE_PROP_LINK() macro
hw/scsi/virtio-scsi: Use VIRTIO_SCSI_COMMON() macro
hw/display/virtio-gpu: Use VIRTIO_DEVICE() macro
hw/block/vhost-user-blk: Use DEVICE() / VIRTIO_DEVICE() macros
hw/virtio/virtio-pmem: Replace impossible check by assertion
hw/s390x/css-bridge: Realize sysbus device before accessing it
hw/isa: Realize ISA bridge device before accessing it
hw/arm/virt: Realize ARM_GICV2M sysbus device before accessing it
hw/acpi: Realize ACPI_GED sysbus device before accessing it
hw/pci-host/bonito: Do not use SysBus API to map local MMIO region
hw/misc/allwinner-dramc: Do not use SysBus API to map local MMIO region
hw/misc/allwinner-dramc: Move sysbus_mmio_map call from init -> realize
hw/i386/intel_iommu: Do not use SysBus API to map local MMIO region
hw/i386/amd_iommu: Do not use SysBus API to map local MMIO region
hw/audio/pcspk: Inline pcspk_init()
hw/intc/spapr_xive: Do not use SysBus API to map local MMIO region
hw/intc/spapr_xive: Move sysbus_init_mmio() calls around
hw/ppc/pnv: Do not use SysBus API to map local MMIO region
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When the host supports the CPU topology facility, the PTF
instruction with function code 2 is interpreted by the SIE,
provided that the userland hypervisor activates the interpretation
by using the KVM_CAP_S390_CPU_TOPOLOGY KVM extension.
The PTF instructions with function code 0 and 1 are intercepted
and must be emulated by the userland hypervisor.
During RESET all CPU of the configuration are placed in
horizontal polarity.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Co-developed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Signed-off-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Message-ID: <20231016183925.2384704-8-nsg@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
During a subsystem reset the Topology-Change-Report is cleared
by the machine.
Let's ask KVM to clear the Modified Topology Change Report (MTCR)
bit of the SCA in the case of a subsystem reset.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Co-developed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Signed-off-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Message-ID: <20231016183925.2384704-7-nsg@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The maximum nested topology entries is used by the guest to
know how many nested topology are available on the machine.
Let change the MNEST value from 2 to 4 in the SCLP READ INFO
structure now that we support books and drawers.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20231016183925.2384704-6-nsg@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
On interception of STSI(15.1.x) the System Information Block
(SYSIB) is built from the list of pre-ordered topology entries.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Co-developed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Message-ID: <20231016183925.2384704-5-nsg@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The topology information are attributes of the CPU and are
specified during the CPU device creation.
On hot plug we:
- calculate the default values for the topology for drawers,
books and sockets in the case they are not specified.
- verify the CPU attributes
- check that we have still room on the desired socket
The possibility to insert a CPU in a mask is dependent on the
number of cores allowed in a socket, a book or a drawer, the
checking is done during the hot plug of the CPU to have an
immediate answer.
If the complete topology is not specified, the core is added
in the physical topology based on its core ID and it gets
defaults values for the modifier attributes.
This way, starting QEMU without specifying the topology can
still get some advantage of the CPU topology.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Co-developed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Message-ID: <20231016183925.2384704-4-nsg@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
S390 adds two new SMP levels, drawers and books to the CPU
topology.
S390 CPUs have specific topology features like dedication and
entitlement. These indicate to the guest information on host
vCPU scheduling and help the guest make better scheduling decisions.
Add the new levels to the relevant QAPI structs.
Add all the supported topology levels, dedication and entitlement
as properties to S390 CPUs.
Create machine-common.json so we can later include it in
machine-target.json also.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Co-developed-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Message-ID: <20231016183925.2384704-3-nsg@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The 64-bit PA-RISC machines use a Astro system bus adapter (SBA)
with Elroy PCI host chips.
Later generation Astro chips were named Pluto, Ike and REO.
Signed-off-by: Helge Deller <deller@gmx.de>
Access to QemuInputHandlerState::handler are read-only.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231017131251.43708-1-philmd@linaro.org>
pcspk_init() is a legacy init function, inline and remove it.
Since the device is realized using &error_fatal, use the same
error for setting the "pit" link.
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20231019073307.99608-1-philmd@linaro.org>
In order to make the next commit trivial, move sysbus_init_mmio()
calls just before the corresponding sysbus_mmio_map() calls.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20231019131647.19690-4-philmd@linaro.org>
pnv_xscom_realize() is not used to *realize* QDev object, rename
it as pnv_xscom_init(). The Error** argument is unused: remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20231019131647.19690-3-philmd@linaro.org>
Fix:
hw/pci/pci.c:504:54: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
MemoryRegion *address_space_io,
^
hw/pci/pci.c:533:38: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
MemoryRegion *address_space_io,
^
hw/pci/pci.c:543:40: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
MemoryRegion *address_space_io,
^
hw/pci/pci.c:590:45: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
MemoryRegion *address_space_io,
^
include/exec/address-spaces.h:35:21: note: previous declaration is here
extern AddressSpace address_space_io;
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231010115048.11856-6-philmd@linaro.org>
Fix:
hw/acpi/pcihp.c:499:36: error: declaration shadows a variable in the global scope [-Werror,-Wshadow]
MemoryRegion *address_space_io,
^
include/exec/address-spaces.h:35:21: note: previous declaration is here
extern AddressSpace address_space_io;
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20231010115048.11856-5-philmd@linaro.org>
When prototyping a heterogenous machine including the ITU,
we get:
include/hw/misc/mips_itu.h:76:5: error: unknown type name 'MIPSCPU'
MIPSCPU *cpu0;
^
MIPSCPU is declared in the target specific "cpu.h" header,
but we don't want to include it, because "cpu.h" is target
specific and its inclusion taints all files including
"mips_itu.h", which become target specific too. We can
however use the 'ArchCPU *' type in the public header.
By keeping the TYPE_MIPS_CPU QOM type check in the link
property declaration, QOM core code will still check the
property is a correct MIPS CPU.
TYPE_MIPS_ITU is still built per-(MIPS)target, but its header
can now be included by other targets.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231009171443.12145-4-philmd@linaro.org>
We already provide "hw/misc/mips_itu.h" to declare prototype
related to MIPSITUState. Move itc_reconfigure() declaration
there.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231009171443.12145-3-philmd@linaro.org>
"hw/mips/cpudevs.h" contains declarations which are specific
to the MIPS architecture; it doesn't make sense for these to
be called from a non-MIPS architecture. Move the declarations
to "target/mips/cpu.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231009171443.12145-2-philmd@linaro.org>
virt.h defines a number of IRQs that are ultimately described by Arm's
Base System Architecture specification. Move these to a dedicated header
so that they can be reused by other platforms that do the same.
Include that header from virt.h to minimise churn.
While we're moving the definitions, sort them into numerical order,
and add the ARCH_TIMER_NS_EL2_VIRT_IRQ definition used by sbsa-ref
and which will eventually be needed by virt also.
Signed-off-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20230919090229.188092-3-quic_llindhol@quicinc.com
[PMM: Remove unused PPI_TO_INTID macro; sort numerically;
add ARCH_TIMER_NS_EL2_VIRT_IRQ]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GIC Private Peripheral Interrupts (PPI) are defined as GIC INTID 16-31.
As in, PPI0 is INTID16 .. PPI15 is INTID31.
Arm's Base System Architecture specification (BSA) lists the mandated and
recommended private interrupt IDs by INTID, not by PPI index. But current
definitions in virt define them by PPI index, complicating cross
referencing.
Meanwhile, the PPI(x) macro counterintuitively adds 16 to the input value,
converting a PPI index to an INTID.
Resolve this by redefining the BSA-allocated PPIs by their INTIDs,
and replacing the PPI(x) macro with an INTID_TO_PPI(x) one where required.
Signed-off-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20230919090229.188092-2-quic_llindhol@quicinc.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This replaces the comma (,) to dot (.) in the device type name
so the name can be used with the 'driver=' command line option.
Signed-off-by: Tong Ho <tong.ho@amd.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20231003052139.199665-1-tong.ho@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
struct arm_boot_info is declared in "hw/arm/boot.h".
By including the correct header we don't need to declare
it again in "target/arm/cpu-qom.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231013130214.95742-1-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The file is obviously related to the raspberrypi machine, so
it should reside in hw/arm/ instead of hw/misc/. And while we're
at it, also adjust the wildcard in MAINTAINERS so that it covers
this file, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231012073458.860187-1-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implementing RAMFB migration is quite straightforward. One caveat is to
treat the whole RAMFBCfg as a blob, since that's what is exposed to the
guest directly. This avoid having to fiddle with endianness issues if we
were to migrate fields individually as integers.
The devices using RAMFB will have to include ramfb_vmstate in their
migration description.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
No functional changes.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move all the code really dependent on the legacy VFIO container/group
into a separate file: container.c. What does remain in common.c is
the code related to VFIOAddressSpace, MemoryListeners, migration and
all other general operations.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Some functions iterate over all the VFIODevices. This is currently
achieved by iterating over all groups/devices. Let's
introduce a global list of VFIODevices simplifying that scan.
This will also be useful while migrating to IOMMUFD by hiding the
group specificity.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
let's store the parent contaienr within the VFIODevice.
This simplifies the logic in vfio_viommu_preset() and
brings the benefice to hide the group specificity which
is useful for IOMMUFD migration.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Several functions need to iterate over the VFIO devices attached to
a given container. This is currently achieved by iterating over the
groups attached to the container and then over the devices in the group.
Let's introduce a per container device list that simplifies this
search.
Per container list is used in below functions:
vfio_devices_all_dirty_tracking
vfio_devices_all_device_dirty_tracking
vfio_devices_all_running_and_mig_active
vfio_devices_dma_logging_stop
vfio_devices_dma_logging_start
vfio_devices_query_dirty_bitmap
This will also ease the migration of IOMMUFD by hiding the group
specificity.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Let the vfio-ccw device use vfio_attach_device() and
vfio_detach_device(), hence hiding the details of the used
IOMMU backend.
Note that the migration reduces the following trace
"vfio: subchannel %s has already been attached" (featuring
cssid.ssid.devid) into "device is already attached"
Also now all the devices have been migrated to use the new
vfio_attach_device/vfio_detach_device API, let's turn the
legacy functions into static functions, local to container.c.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
We want the VFIO devices to be able to use two different
IOMMU backends, the legacy VFIO one and the new iommufd one.
Introduce vfio_[attach/detach]_device which aim at hiding the
underlying IOMMU backend (IOCTLs, datatypes, ...).
Once vfio_attach_device completes, the device is attached
to a security context and its fd can be used. Conversely
When vfio_detach_device completes, the device has been
detached from the security context.
At the moment only the implementation based on the legacy
container/group exists. Let's use it from the vfio-pci device.
Subsequent patches will handle other devices.
We also take benefit of this patch to properly free
vbasedev->name on failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Introduce two new helpers, vfio_kvm_device_[add/del]_fd
which take as input a file descriptor which can be either a group fd or
a cdev fd. This uses the new KVM_DEV_VFIO_FILE VFIO KVM device group,
which aliases to the legacy KVM_DEV_VFIO_GROUP.
vfio_kvm_device_[add/del]_group then call those new helpers.
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Move low-level iommu agnostic helpers to a separate helpers.c
file. They relate to regions, interrupts, device/region
capabilities and etc.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZSimNQAKCRBAov/yOSY+
33XwBADF9ZKlESDBDa/huNFAKD7BsUIdglHfz9lHnLY+kQbCun4HyTLtp2IBsySu
mZTjdfU/LnaBidFLjEnmZZMPyiI3oV1ruSzT53egSDaxrFUXGpc9oxtMNLsyfk9P
swdngG13Fc9sWVKC7IJeYDYXgkvHY7NxsiV8U9vdqXOyw2uoHA==
=ufPc
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20231013' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20231013
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZSimNQAKCRBAov/yOSY+
# 33XwBADF9ZKlESDBDa/huNFAKD7BsUIdglHfz9lHnLY+kQbCun4HyTLtp2IBsySu
# mZTjdfU/LnaBidFLjEnmZZMPyiI3oV1ruSzT53egSDaxrFUXGpc9oxtMNLsyfk9P
# swdngG13Fc9sWVKC7IJeYDYXgkvHY7NxsiV8U9vdqXOyw2uoHA==
# =ufPc
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 12 Oct 2023 22:06:45 EDT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20231013' of https://gitlab.com/gaosong/qemu:
LoongArch: step down as general arch maintainer
hw/loongarch/virt: Remove unused 'loongarch_virt_pm' region
hw/loongarch/virt: Remove unused ISA Bus
hw/loongarch/virt: Remove unused ISA UART
hw/loongarch: remove global loaderparams variable
target/loongarch: Add preldx instruction
target/loongarch: fix ASXE flag conflict
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This modifies the common virtio-gpu.h file have the fields and
defintions needed by gfxstream/rutabaga, by VirtioGpuRutabaga.
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Tested-by: Alyssa Ross <hi@alyssa.is>
Tested-by: Emmanouil Pitsidianakis <manos.pitsidianakis@linaro.org>
Tested-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Emmanouil Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Antonio Caggiano <quic_acaggian@quicinc.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Use VIRTIO_GPU_SHM_ID_HOST_VISIBLE as id for virtio-gpu.
Signed-off-by: Antonio Caggiano <antonio.caggiano@collabora.com>
Tested-by: Alyssa Ross <hi@alyssa.is>
Tested-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Huang Rui <ray.huang@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Define a new capability type 'VIRTIO_PCI_CAP_SHARED_MEMORY_CFG' to allow
defining shared memory regions with sizes and offsets of 2^32 and more.
Multiple instances of the capability are allowed and distinguished
by a device-specific 'id'.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Antonio Caggiano <antonio.caggiano@collabora.com>
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Tested-by: Alyssa Ross <hi@alyssa.is>
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Gurchetan Singh <gurchetansingh@chromium.org>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
The LoongArch 'virt' machine doesn't use its ISA I/O region.
If a ISA device were to be mapped there, there is no support
for ISA IRQ. Unlikely useful. Simply remove.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231010135342.40219-3-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Having large virtio-mem devices that only expose little memory to a VM
is currently a problem: we map the whole sparse memory region into the
guest using a single memslot, resulting in one gigantic memslot in KVM.
KVM allocates metadata for the whole memslot, which can result in quite
some memory waste.
Assuming we have a 1 TiB virtio-mem device and only expose little (e.g.,
1 GiB) memory, we would create a single 1 TiB memslot and KVM has to
allocate metadata for that 1 TiB memslot: on x86, this implies allocating
a significant amount of memory for metadata:
(1) RMAP: 8 bytes per 4 KiB, 8 bytes per 2 MiB, 8 bytes per 1 GiB
-> For 1 TiB: 2147483648 + 4194304 + 8192 = ~ 2 GiB (0.2 %)
With the TDP MMU (cat /sys/module/kvm/parameters/tdp_mmu) this gets
allocated lazily when required for nested VMs
(2) gfn_track: 2 bytes per 4 KiB
-> For 1 TiB: 536870912 = ~512 MiB (0.05 %)
(3) lpage_info: 4 bytes per 2 MiB, 4 bytes per 1 GiB
-> For 1 TiB: 2097152 + 4096 = ~2 MiB (0.0002 %)
(4) 2x dirty bitmaps for tracking: 2x 1 bit per 4 KiB page
-> For 1 TiB: 536870912 = 64 MiB (0.006 %)
So we primarily care about (1) and (2). The bad thing is, that the
memory consumption *doubles* once SMM is enabled, because we create the
memslot once for !SMM and once for SMM.
Having a 1 TiB memslot without the TDP MMU consumes around:
* With SMM: 5 GiB
* Without SMM: 2.5 GiB
Having a 1 TiB memslot with the TDP MMU consumes around:
* With SMM: 1 GiB
* Without SMM: 512 MiB
... and that's really something we want to optimize, to be able to just
start a VM with small boot memory (e.g., 4 GiB) and a virtio-mem device
that can grow very large (e.g., 1 TiB).
Consequently, using multiple memslots and only mapping the memslots we
really need can significantly reduce memory waste and speed up
memslot-related operations. Let's expose the sparse RAM memory region using
multiple memslots, mapping only the memslots we currently need into our
device memory region container.
The feature can be enabled using "dynamic-memslots=on" and requires
"unplugged-inaccessible=on", which is nowadays the default.
Once enabled, we'll auto-detect the number of memslots to use based on the
memslot limit provided by the core. We'll use at most 1 memslot per
gigabyte. Note that our global limit of memslots accross all memory devices
is currently set to 256: even with multiple large virtio-mem devices,
we'd still have a sane limit on the number of memslots used.
The default is to not dynamically map memslot for now
("dynamic-memslots=off"). The optimization must be enabled manually,
because some vhost setups (e.g., hotplug of vhost-user devices) might be
problematic until we support more memslots especially in vhost-user backends.
Note that "dynamic-memslots=on" is just a hint that multiple memslots
*may* be used for internal optimizations, not that multiple memslots
*must* be used. The actual number of memslots that are used is an
internal detail: for example, once memslot metadata is no longer an
issue, we could simply stop optimizing for that. Migration source and
destination can differ on the setting of "dynamic-memslots".
Message-ID: <20230926185738.277351-17-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We want to support memory devices that can automatically decide how many
memslots they will use. In the worst case, they have to use a single
memslot.
The target use cases are virtio-mem and the hyper-v balloon.
Let's calculate a reasonable limit such a memory device may use, and
instruct the device to make a decision based on that limit. Use a simple
heuristic that considers:
* A memslot soft-limit for all memory devices of 256; also, to not
consume too many memslots -- which could harm performance.
* Actually still free and unreserved memslots
* The percentage of the remaining device memory region that memory device
will occupy.
Further, while we properly check before plugging a memory device whether
there still is are free memslots, we have other memslot consumers (such as
boot memory, PCI BARs) that don't perform any checks and might dynamically
consume memslots without any prior reservation. So we might succeed in
plugging a memory device, but once we dynamically map a PCI BAR we would
be in trouble. Doing accounting / reservation / checks for all such
users is problematic (e.g., sometimes we might temporarily split boot
memory into two memslots, triggered by the BIOS).
We use the historic magic memslot number of 509 as orientation to when
supporting 256 memory devices -> memslots (leaving 253 for boot memory and
other devices) has been proven to work reliable. We'll fallback to
suggesting a single memslot if we don't have at least 509 total memslots.
Plugging vhost devices with less than 509 memslots available while we
have memory devices plugged that consume multiple memslots due to
automatic decisions can be problematic. Most configurations might just fail
due to "limit < used + reserved", however, it can also happen that these
memory devices would suddenly consume memslots that would actually be
required by other memslot consumers (boot, PCI BARs) later. Note that this
has always been sketchy with vhost devices that support only a small number
of memslots; but we don't want to make it any worse.So let's keep it simple
and simply reject plugging such vhost devices in such a configuration.
Eventually, all vhost devices that want to be fully compatible with such
memory devices should support a decent number of memslots (>= 509).
Message-ID: <20230926185738.277351-13-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's add vhost_get_max_memslots().
Message-ID: <20230926185738.277351-12-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We want to support memory devices that have a dynamically managed memory
region container as device memory region. This device memory region maps
multiple RAM memory subregions (e.g., aliases to the same RAM memory
region), whereby these subregions can be (un)mapped on demand.
Each RAM subregion will consume a memslot in KVM and vhost, resulting in
such a new device consuming memslots dynamically, and initially usually
0. We already track the number of used vs. required memslots for all
memslots. From that, we can derive the number of reserved memslots that
must not be used otherwise.
The target use case is virtio-mem and the hyper-v balloon, which will
dynamically map aliases to RAM memory region into their device memory
region container.
Properly document what's supported and what's not and extend the vhost
memslot check accordingly.
Message-ID: <20230926185738.277351-10-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's track how many memslots are required by plugged memory devices and
how many are currently actually getting used by plugged memory
devices.
"required - used" is the number of reserved memslots. For now, the number
of used and required memslots is always equal, and there are no
reservations. This is a preparation for memory devices that want to
dynamically consume memslots after initially specifying how many they
require -- where we'll end up with reserved memslots.
To track the number of used memslots, create a new address space for
our device memory and register a memory listener (add/remove) for that
address space.
Message-ID: <20230926185738.277351-9-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
We want to support memory devices that have a memory region container as
device memory region that maps multiple RAM memory regions. Let's start
by supporting memory devices that statically map multiple RAM memory
regions and, thereby, consume multiple memslots.
We already have one device that uses a container as device memory region:
NVDIMMs. However, a NVDIMM always ends up consuming exactly one memslot.
Let's add support for that by asking the memory device via a new
callback how many memslots it requires.
Message-ID: <20230926185738.277351-7-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's return the number of free slots instead of only checking if there
is a free slot. Required to support memory devices that consume multiple
memslots.
This is a preparation for memory devices that consume multiple memslots.
Message-ID: <20230926185738.277351-6-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Checking whether the memory regions are equal is sufficient: if they are
equal, then most certainly the contained fd is equal.
The whole vhost-user memslot handling is suboptimal and overly
complicated. We shouldn't have to lookup a RAM memory regions we got
notified about in vhost_user_get_mr_data() using a host pointer. But that
requires a bigger rework -- especially an alternative vhost_set_mem_table()
backend call that simply consumes MemoryRegionSections.
For now, let's just drop vhost_backend_can_merge().
Message-ID: <20230926185738.277351-3-david@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Having multiple vhost devices, some filtering out fd-less memslots and
some not, can mess up the "used_memslot" accounting. Consequently our
"free memslot" checks become unreliable and we might run out of free
memslots at runtime later.
An example sequence which can trigger a potential issue that involves
different vhost backends (vhost-kernel and vhost-user) and hotplugged
memory devices can be found at [1].
Let's make the filtering mechanism less generic and distinguish between
backends that support private memslots (without a fd) and ones that only
support shared memslots (with a fd). Track the used_memslots for both
cases separately and use the corresponding value when required.
Note: Most probably we should filter out MAP_PRIVATE fd-based RAM regions
(for example, via memory-backend-memfd,...,shared=off or as default with
memory-backend-file) as well. When not using MAP_SHARED, it might not work
as expected. Add a TODO for now.
[1] https://lkml.kernel.org/r/fad9136f-08d3-3fd9-71a1-502069c000cf@redhat.com
Message-ID: <20230926185738.277351-2-david@redhat.com>
Fixes: 988a27754b ("vhost: allow backends to filter memory sections")
Cc: Tiwei Bie <tiwei.bie@intel.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Avoid using trivial variable names in macros, otherwise we get
the following compiler warning when compiling with -Wshadow=local:
In file included from ../../qemu/hw/display/virtio-gpu-virgl.c:19:
../../home/thuth/devel/qemu/hw/display/virtio-gpu-virgl.c:
In function ‘virgl_cmd_submit_3d’:
../../qemu/include/hw/virtio/virtio-gpu.h:228:16: error: declaration of ‘s’
shadows a previous local [-Werror=shadow=compatible-local]
228 | size_t s;
| ^
../../qemu/hw/display/virtio-gpu-virgl.c:215:5: note: in expansion of macro
‘VIRTIO_GPU_FILL_CMD’
215 | VIRTIO_GPU_FILL_CMD(cs);
| ^~~~~~~~~~~~~~~~~~~
../../qemu/hw/display/virtio-gpu-virgl.c:213:12: note: shadowed declaration
is here
213 | size_t s;
| ^
cc1: all warnings being treated as errors
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20231009084559.41427-1-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
An array is a more appropriate data structure than a list for gdb_regs
since it is initialized only with append operation and read-only after
initialization.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230912224107.29669-13-akihiko.odaki@daynix.com>
[AJB: fixed a checkpatch violation]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231009164104.369749-20-alex.bennee@linaro.org>
All implementations of gdb_arch_name() returns dynamic duplicates of
static strings. It's also unlikely that there will be an implementation
of gdb_arch_name() that returns a truly dynamic value due to the nature
of the function returning a well-known identifiers. Qualify the value
gdb_arch_name() with const and make all of its implementations return
static strings.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230912224107.29669-8-akihiko.odaki@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231009164104.369749-15-alex.bennee@linaro.org>
add support for booting:
- MacOS 7.1 - 8.1, with or without virtual memory enabled
- A/UX 3.0.1
- NetBSD 9.3
- Linux (via EMILE)
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEzS913cjjpNwuT1Fz8ww4vT8vvjwFAmUiSrISHGxhdXJlbnRA
dml2aWVyLmV1AAoJEPMMOL0/L748oSUQAKAm3TPYQUDDVFTi2uhzv6IgNSgOVUhK
3I3xoNb0UR9AT3Wfg1fah5La3p0kL9Y25gvhCl6veUg39WVicv3fbqUevbJ1Nwgl
ovwS3MRRcvYhU+omcXImFfoIPyOxfSf3vZ6SedIkB24hQyXN9eFBZMfgCODU6lfo
rAd/Hm50N2jRI8aKjvN+uHFRz75wqq6rNk/4QLWihRqhtWrjUDPHOTMI9sQxWy9z
LcXxVKbWCY8/WOAandsGL94l2jfu94HM6CfwHaumdxvPBZT6WUyCv3T1rJsVJU29
b8oTLcwKAmZ7lGLbjl6GdB8q5KAJFCAGLWuEbNIMj0orB37OpUd0Wx2SD9+aA53H
yoKGbk6N1UappTtcnZCfwzWRzNaXrRno+w+/xYjlKsXBdHV9ZXHMGD5ERxoC6MY7
ISsCa4bafeUDes6SCetgq87ho69E8l+gAlNYPgidHaTP226BjrYWQRJIa0leczfO
aE6dAG7MQFOnOjeOHEJMDB2XpKHiVe1lyVGQH485cLW1J6LHJFWUfUUH2Zjs1v1z
eXZHBTclPO2wbuQzXG6pAz2jdF/9w4ft/aA0PQhQcFxa9RB6AoNFG/juHJN5eUiw
NXJetR2g1juNPqmMFWDNMJ7Zzce5Chjoj69XJBFYSXhgbOtwpUpoEPZUeIMcW1eJ
Va2HvyDQPp1B
=RUHg
-----END PGP SIGNATURE-----
Merge tag 'q800-for-8.2-pull-request' of https://github.com/vivier/qemu-m68k into staging
Pull request q800 20231008
add support for booting:
- MacOS 7.1 - 8.1, with or without virtual memory enabled
- A/UX 3.0.1
- NetBSD 9.3
- Linux (via EMILE)
# -----BEGIN PGP SIGNATURE-----
#
# iQJGBAABCAAwFiEEzS913cjjpNwuT1Fz8ww4vT8vvjwFAmUiSrISHGxhdXJlbnRA
# dml2aWVyLmV1AAoJEPMMOL0/L748oSUQAKAm3TPYQUDDVFTi2uhzv6IgNSgOVUhK
# 3I3xoNb0UR9AT3Wfg1fah5La3p0kL9Y25gvhCl6veUg39WVicv3fbqUevbJ1Nwgl
# ovwS3MRRcvYhU+omcXImFfoIPyOxfSf3vZ6SedIkB24hQyXN9eFBZMfgCODU6lfo
# rAd/Hm50N2jRI8aKjvN+uHFRz75wqq6rNk/4QLWihRqhtWrjUDPHOTMI9sQxWy9z
# LcXxVKbWCY8/WOAandsGL94l2jfu94HM6CfwHaumdxvPBZT6WUyCv3T1rJsVJU29
# b8oTLcwKAmZ7lGLbjl6GdB8q5KAJFCAGLWuEbNIMj0orB37OpUd0Wx2SD9+aA53H
# yoKGbk6N1UappTtcnZCfwzWRzNaXrRno+w+/xYjlKsXBdHV9ZXHMGD5ERxoC6MY7
# ISsCa4bafeUDes6SCetgq87ho69E8l+gAlNYPgidHaTP226BjrYWQRJIa0leczfO
# aE6dAG7MQFOnOjeOHEJMDB2XpKHiVe1lyVGQH485cLW1J6LHJFWUfUUH2Zjs1v1z
# eXZHBTclPO2wbuQzXG6pAz2jdF/9w4ft/aA0PQhQcFxa9RB6AoNFG/juHJN5eUiw
# NXJetR2g1juNPqmMFWDNMJ7Zzce5Chjoj69XJBFYSXhgbOtwpUpoEPZUeIMcW1eJ
# Va2HvyDQPp1B
# =RUHg
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 08 Oct 2023 02:22:42 EDT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* tag 'q800-for-8.2-pull-request' of https://github.com/vivier/qemu-m68k:
mac_via: extend timer calibration hack to work with A/UX
q800: add alias for MacOS toolbox ROM at 0x40000000
q800: add ESCC alias at 0xc000
mac_via: always clear ADB interrupt when switching to A/UX mode
mac_via: implement ADB_STATE_IDLE state if shift register in input mode
mac_via: workaround NetBSD ADB bus enumeration issue
mac_via: work around underflow in TimeDBRA timing loop in SETUPTIMEK
swim: update IWM/ISM register block decoding
swim: split into separate IWM and ISM register blocks
swim: add trace events for IWM and ISM registers
q800: add easc bool machine class property to switch between ASC and EASC
q800: add Apple Sound Chip (ASC) audio to machine
asc: generate silence if FIFO empty but engine still running
audio: add Apple Sound Chip (ASC) emulation
q800: allow accesses to RAM area even if less memory is available
q800: add IOSB subsystem
q800: implement additional machine id bits on VIA1 port A
q800: add machine id register
q800: add djMEMC memory controller
q800-glue.c: convert to Resettable interface
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
According to the Apple Quadra 800 Developer Note document, the Quadra 800 ROM
consists of 2 ROM code sections based at offsets 0x0 and 0x800000. A/UX attempts
to access the toolbox ROM at the lower offset during startup, so provide a
memory alias to allow the access to succeed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tests on real Q800 hardware show that the ESCC is addressable at multiple locations
within the ESCC memory region - at least 0xc000, 0xc020 (as expected by the MacOS
toolbox ROM) and 0xc040.
All released NetBSD kernels before 10 use the 0xc000 address which causes a fatal
error when running the MacOS booter. Add a single memory region alias at 0xc000
to enable NetBSD kernels to start booting under QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS toolbox ROM calculates the number of branches that can be executed
per millisecond as part of its timer calibration. Since modern hosts are
considerably quicker than original hardware, the negative counter reaches zero
before the calibration completes leading to division by zero later in
CALCULATESLOD.
Instead of trying to fudge the timing loop (which won't work for TimeDBRA/TimeSCCDB
anyhow), use the pattern of access to the VIA1 registers to detect when SETUPTIMEK
has finished executing and write some well-known good timer values to TimeDBRA
and TimeSCCDB taken from real hardware with a suitable scaling factor.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Update the IWM/ISM register block decoding to match the description given in the
"SWIM Chip Users Reference". This allows us to validate the device response to
the guest OS which currently only does just enough to indicate that the floppy
drive is unavailable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The swim chip provides an implementation of both Apple's IWM and ISM floppy disk
controllers. Split the existing implementation into separate register banks for
each controller, whilst also switching the IWM registers from 16-bit to 8-bit
as implemented in real hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This determines whether the Apple Sound Chip (ASC) is set to enhanced mode
(default) or to original mode. The real Q800 hardware used an EASC chip however
a lot of older software only works with the older ASC chip.
Adding this as a machine parameter allows QEMU to be used as an developer aid
for testing and migrating code from ASC to EASC.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Quadra 800 has the enhanced ASC (EASC) audio chip which supports both the
legacy IRQ routing through VIA2 and also "A/UX" mode routing direct to the
CPU.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231004083806.757242-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS (un)helpfully leaves the FIFO engine running even when all the samples have
been written to the hardware, and expects the FIFO status flags and IRQ to be
updated continuously.
There is an additional problem in that not all audio backends guarantee an
all-zero output when there is no FIFO data available, in particular the Windows
dsound backend which re-uses its internal circular buffer causing the last played
sound to loop indefinitely.
Whilst this is effectively a bug in the Windows dsound backend, work around it
for now using a simple heuristic: if the FIFO remains empty for half a cycle
(~23ms) then continuously fill the generated buffer with empty silence.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Apple Sound Chip was primarily used by the Macintosh II to generate sound
in hardware which was previously handled by the toolbox ROM with software
interrupts.
Implement both the standard ASC and also the enhanced ASC (EASC) functionality
which is used in the Quadra 800.
Note that whilst real ASC hardware uses AUDIO_FORMAT_S8, this implementation uses
AUDIO_FORMAT_U8 instead because AUDIO_FORMAT_S8 is rarely used and not supported
by some audio backends like PulseAudio and DirectSound when played directly with
-audiodev out.mixing-engine=off.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Co-developed-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231004083806.757242-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS attempts a series of writes and reads over the entire RAM area in order
to determine the amount of RAM within the machine. Allow accesses to the
entire RAM area ignoring writes and always reading zero for areas where there
is no physical RAM installed to allow MacOS to detect the memory size without
faulting.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It is needed because it defines the BIOSConfig area.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <20231004083806.757242-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS reads this address to identify the hardware.
This is a basic implementation returning the ID of Quadra 800.
Details:
http://mess.redump.net/mess/driver_info/mac_technical_notes
"There are 3 ID schemes [...]
The third and most scalable is a machine ID register at 0x5ffffffc.
The top word must be 0xa55a to be valid. Then bits 15-11 are 0 for
consumer Macs, 1 for portables, 2 for high-end 68k, and 3 for high-end
PowerPC. Bit 10 is 1 if additional ID bits appear elsewhere (e.g. in VIA1).
The rest of the bits are a per-model identifier.
Model Lower 16 bits of ID
...
Quadra/Centris 610/650/800 0x2BAD"
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The djMEMC controller is used to store information related to the physical memory
configuration.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
vdpa:
shadow vq vlan support
net migration with cvq
cxl:
support emulating 4 HDM decoders
serial number extended capability
virtio:
hared dma-buf
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmUd4/YPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpyM8H/02cRbJcQOjYt7j68zPW6GaDXxBI/UmdWDyG
15LZZbGNOPjyjNd3Vz1M7stQ5rhoKcgo/RdI+0E60a78svgW5JvpXoXR3pksc3Dx
v28B/akXwHUErYFSZQ+2VHNc8OhCd0v2ehxZxbwPEAYIOAj3hcCIVoPGXTnKJmAJ
imr5hjH0wZUc0+xdsmn8Vfdv5NTzpwfVObbGiMZejeJsaoh0y6Rt8RANBMY67KQD
S7/HPlVuDYf/y43t4ZEHNYuV9RaCdZZYlLWwV1scdKaYcofgmtJOKbOdCjHRXgj+
004Afb3rggIoCfnCzOFzhGx+MLDtLjvEn2N4oLEWCLi+k/3huaA=
=GAvH
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pci: features, cleanups
vdpa:
shadow vq vlan support
net migration with cvq
cxl:
support emulating 4 HDM decoders
serial number extended capability
virtio:
hared dma-buf
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (53 commits)
libvhost-user: handle shared_object msg
vhost-user: add shared_object msg
hw/display: introduce virtio-dmabuf
util/uuid: add a hash function
virtio: remove unused next argument from virtqueue_split_read_next_desc()
virtio: remove unnecessary thread fence while reading next descriptor
virtio: use shadow_avail_idx while checking number of heads
libvhost-user.c: add assertion to vu_message_read_default
pcie_sriov: unregister_vfs(): fix error path
hw/i386/pc: improve physical address space bound check for 32-bit x86 systems
amd_iommu: Fix APIC address check
vdpa net: follow VirtIO initialization properly at cvq isolation probing
vdpa net: stop probing if cannot set features
vdpa net: fix error message setting virtio status
hw/pci-bridge/cxl-upstream: Add serial number extended capability support
hw/cxl: Support 4 HDM decoders at all levels of topology
hw/cxl: Fix and use same calculation for HDM decoder block size everywhere
hw/cxl: Add utility functions decoder interleave ways and target count.
hw/cxl: Push cxl_decoder_count_enc() and cxl_decode_ig() into .c
vdpa net: zero vhost_vdpa iova_tree pointer at cleanup
...
Conflicts:
hw/core/machine.c
Context conflict with commit 314e0a84cd ("hw/core: remove needless
includes") because it removed an adjacent #include.
Add three new vhost-user protocol
`VHOST_USER_BACKEND_SHARED_OBJECT_* messages`.
These new messages are sent from vhost-user
back-ends to interact with the virtio-dmabuf
table in order to add or remove themselves as
virtio exporters, or lookup for virtio dma-buf
shared objects.
The action taken in the front-end depends
on the type stored in the virtio shared
object hash table.
When the table holds a pointer to a vhost
backend for a given UUID, the front-end sends
a VHOST_USER_GET_SHARED_OBJECT to the
backend holding the shared object.
The messages can only be sent after successfully
negotiating a new VHOST_USER_PROTOCOL_F_SHARED_OBJECT
vhost-user protocol feature bit.
Finally, refactor code to send response message so
that all common parts both for the common REPLY_ACK
case, and other data responses, can call it and
avoid code repetition.
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-4-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This API manages objects (in this iteration,
dmabuf fds) that can be shared along different
virtio devices, associated to a UUID.
The API allows the different devices to add,
remove and/or retrieve the objects by simply
invoking the public functions that reside in the
virtio-dmabuf file.
For vhost backends, the API stores the pointer
to the backend holding the object.
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20231002065706.94707-3-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
32-bit x86 systems do not have a reserved memory for hole64. On those 32-bit
systems without PSE36 or PAE CPU features, hotplugging memory devices are not
supported by QEMU as QEMU always places hotplugged memory above 4 GiB boundary
which is beyond the physical address space of the processor. Linux guests also
does not support memory hotplug on those systems. Please see Linux
kernel commit b59d02ed08690 ("mm/memory_hotplug: disable the functionality
for 32b") for more details.
Therefore, the maximum limit of the guest physical address in the absence of
additional memory devices effectively coincides with the end of
"above 4G memory space" region for 32-bit x86 without PAE/PSE36. When users
configure additional memory devices, after properly accounting for the
additional device memory region to find the maximum value of the guest
physical address, the address will be outside the range of the processor's
physical address space.
This change adds improvements to take above into consideration.
For example, previously this was allowed:
$ ./qemu-system-x86_64 -cpu pentium -m size=10G
With this change now it is no longer allowed:
$ ./qemu-system-x86_64 -cpu pentium -m size=10G
qemu-system-x86_64: Address space limit 0xffffffff < 0x2bfffffff phys-bits too low (32)
However, the following are allowed since on both cases physical address
space of the processor is 36 bits:
$ ./qemu-system-x86_64 -cpu pentium2 -m size=10G
$ ./qemu-system-x86_64 -cpu pentium,pse36=on -m size=10G
For 32-bit, without PAE/PSE36, hotplugging additional memory is no longer allowed.
$ ./qemu-system-i386 -m size=1G,maxmem=3G,slots=2
qemu-system-i386: Address space limit 0xffffffff < 0x1ffffffff phys-bits too low (32)
$ ./qemu-system-i386 -machine q35 -m size=1G,maxmem=3G,slots=2
qemu-system-i386: Address space limit 0xffffffff < 0x1ffffffff phys-bits too low (32)
A new compatibility flag is introduced to make sure pc_max_used_gpa() keeps
returning the old value for machines 8.1 and older.
Therefore, the above is still allowed for older machine types in order to support
compatibility. Hence, the following still works:
$ ./qemu-system-i386 -machine pc-i440fx-8.1 -m size=1G,maxmem=3G,slots=2
$ ./qemu-system-i386 -machine pc-q35-8.1 -m size=1G,maxmem=3G,slots=2
Further, following is also allowed as with PSE36, the processor has 36-bit
address space:
$ ./qemu-system-i386 -cpu 486,pse36=on -m size=1G,maxmem=3G,slots=2
After calling CPUID with EAX=0x80000001, all AMD64 compliant processors
have the longmode-capable-bit turned on in the extended feature flags (bit 29)
in EDX. The absence of CPUID longmode can be used to differentiate between
32-bit and 64-bit processors and is the recommended approach. QEMU takes this
approach elsewhere (for example, please see x86_cpu_realizefn()), With
this change, pc_max_used_gpa() also uses the same method to detect 32-bit
processors.
Unit tests are modified to not run 32-bit x86 tests that use memory hotplug.
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230922160413.165702-1-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support these decoders in CXL host bridges (pxb-cxl), CXL Switch USP
and CXL Type 3 end points.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to avoid having the size of the per HDM decoder register block
repeated in lots of places, create the register definitions for HDM
decoder 1 and use the offset between the first registers in HDM decoder 0 and
HDM decoder 1 to establish the offset.
Calculate in each function as this is more obvious and leads to shorter
line lengths than a single #define which would need a long name
to be specific enough.
Note that the code currently only supports one decoder, so the bugs this
fixes don't actually affect anything.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230913132523.29780-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As an encoded version of these key configuration parameters is available
in a register, provide functions to extract it again so as to avoid
the need for duplicating the storage.
Whilst here update the _enc() function to include additional values
as defined in the CXL 3.0 specification. Whilst they are not
currently used in the emulation, they may be in future and it is
easier to compare with the specification if all values are covered.
Add a spec reference for cxl_interleave_ways_enc() for consistency
with the target count equivalent (and because it's nice to know where
the magic numbers come from).
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no strong justification for keeping these in the header
so push them down into the associated cxl-component-utils.c file.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913132523.29780-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that TYPE_ACPI_GED_X86 doesn't assign AcpiDeviceIfClass::madt_cpu any more
it is the same as TYPE_ACPI_GED.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "hw/boards.h" is unused since the previous commit. Since its removal
requires include fixes in various unrelated files to keep the code compiling it
has been split in a dedicated commit.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This virtual method was always set to the x86-specific pc_madt_cpu_entry(),
even in piix4 which is also used in MIPS. The previous changes use
pc_madt_cpu_entry() otherwise, so madt_cpu can be dropped.
Since pc_madt_cpu_entry() is now only used in x86-specific code, the stub
in hw/acpi/acpi-x86-stub can be removed as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
build_cpus_aml() is architecture independent but needs to create architecture-
specific CPU AML. So far this was achieved by using a virtual method from
TYPE_ACPI_DEVICE_IF. However, build_cpus_aml() would resolve this interface from
global (!) state. This makes it quite incomprehensible where this interface
comes from (TYPE_PIIX4_PM?, TYPE_ICH9_LPC_DEVICE?, TYPE_ACPI_GED_X86?) an can
lead to crashes when the generic code is ported to new architectures.
So far, build_cpus_aml() is only called in architecture-specific code -- and
only in x86. We can therefore simply pass pc_madt_cpu_entry() as callback to
build_cpus_aml(). This is the same callback that would be used through
TYPE_ACPI_DEVICE_IF.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230908084234.17642-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move the definition of VhostUserProtocolFeature to
include/hw/virtio/vhost-user.h.
Remove previous definitions in hw/scsi/vhost-user-scsi.c,
hw/virtio/vhost-user.c, and hw/virtio/virtio-qmp.c.
Previously there were 3 separate definitions of this over 3 different
files. Now only 1 definition of this will be present for these 3 files.
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Reviewed-by: Emmanouil Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20230926224107.2951144-4-jonah.palmer@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The vhost-vdpa net backend needs to enable vrings in a different order
than default, so export it.
No functional change intended except for tracing, that now includes the
(virtio) index being enabled and the return value of the ioctl.
Still ignoring return value of this function if called from
vhost_vdpa_dev_start, as reorganize calling code around it is out of
the scope of this series.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230822085330.3978829-3-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-vdpa shadowed CVQ needs to know the maximum number of
vlans supported by the virtio-net device, so QEMU can restore
the VLAN state in a migration.
Co-developed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <ca03403319c6405ea7c400836a572255bbc9ceba.1690106284.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To use the generic device the user will need to provide the config
region size via the command line. We also add a notifier so the guest
can be pinged if the remote daemon updates the config.
With these changes:
-device vhost-user-device-pci,virtio-id=41,num_vqs=2,config_size=8
is equivalent to:
-device vhost-user-gpio-pci
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-11-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In theory we shouldn't need to repeat so much boilerplate to support
vhost-user backends. This provides a generic vhost-user-base QOM
object and a derived vhost-user-device for which the user needs to
provide the few bits of information that aren't currently provided by
the vhost-user protocol. This should provide a baseline implementation
from which the other vhost-user stub can specialise.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-8-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
current code sets PCI_SEC_LATENCY_TIMER to RW, but for
pcie to pcie bridges it must be RO 0 according to
pci express spec which says:
This register does not apply to PCI Express. It must be read-only
and hardwired to 00h. For PCI Express to PCI/PCI-X Bridges, refer to the
[PCIe-to-PCI-PCI-X-Bridge] for requirements for this register.
also, fix typo in comment where it's made writeable - this typo
is likely what prevented us noticing we violate this requirement
in the 1st place.
Reported-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-Id: <de9d05366a70172e1789d10591dbe59e39c3849c.1693432039.git.mst@redhat.com>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Minimize the displacement to can_do_io, since it may
be touched at the start of each TranslationBlock.
It fits into other padding within the substructure.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Retain the separate structure to emphasize its importance.
Enforce CPUArchState always follows CPUState without padding.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Accept that we will consume space in CPUState for CONFIG_USER_ONLY,
since we cannot test CONFIG_SOFTMMU within hw/core/cpu.h.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The AccelCPUClass::cpu_realizefn handler is meant for target
specific code, rename it using '_target_' to emphasis it.
Suggested-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20231003123026.99229-3-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* fix for KVM on Apple M2
* introduce machine property "audiodev"
* ui/vnc: Require audiodev= to enable audio
* audio: remove QEMU_AUDIO_* and -audio-help support
* audio: forbid using default audiodev backend with -audiodev and -nodefaults
* remove compatibility code for old machine types
* make-release: do not ship dtc sources
* build system cleanups
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmUb0QgUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOpnAf9EFXfGkXpqQ5Q8ZbVlVc5GQKofMHW
OZwamTBlp/c07+QcQiMxwLhIW0iyDhrfdCjoFSUaTA8O10FM1YrFv4SkUryYb9B3
bmoTl4NeLvmkxpC47GEeaaBfjyM0G/9Ip9Zsuqx3u+gSzwTbkEstA2u7gcsN0tL9
VlhMSiV82uHhRC/DJYLxr+8bRYSIm1AeuI8K/O1yags85Kztf3UiQUhePIKLznMH
BdORjD+i46xM1dE8ifpdsunm462cDWz/faAnIH0YVKBlshnQHXKTO+GDA/Fbfl51
wFfupZXo93wwgawS7elAUzI+gwaKCPRHA8NDcukeO91hTzk6i14y04u5SQ==
=nv64
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* fix from optionrom build
* fix for KVM on Apple M2
* introduce machine property "audiodev"
* ui/vnc: Require audiodev= to enable audio
* audio: remove QEMU_AUDIO_* and -audio-help support
* audio: forbid using default audiodev backend with -audiodev and -nodefaults
* remove compatibility code for old machine types
* make-release: do not ship dtc sources
* build system cleanups
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmUb0QgUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroOpnAf9EFXfGkXpqQ5Q8ZbVlVc5GQKofMHW
# OZwamTBlp/c07+QcQiMxwLhIW0iyDhrfdCjoFSUaTA8O10FM1YrFv4SkUryYb9B3
# bmoTl4NeLvmkxpC47GEeaaBfjyM0G/9Ip9Zsuqx3u+gSzwTbkEstA2u7gcsN0tL9
# VlhMSiV82uHhRC/DJYLxr+8bRYSIm1AeuI8K/O1yags85Kztf3UiQUhePIKLznMH
# BdORjD+i46xM1dE8ifpdsunm462cDWz/faAnIH0YVKBlshnQHXKTO+GDA/Fbfl51
# wFfupZXo93wwgawS7elAUzI+gwaKCPRHA8NDcukeO91hTzk6i14y04u5SQ==
# =nv64
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 03 Oct 2023 04:30:00 EDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (24 commits)
audio: forbid default audiodev backend with -nodefaults
audio: propagate Error * out of audio_init
vt82c686 machines: Support machine-default audiodev with fallback
hw/ppc: Support machine-default audiodev with fallback
hw/arm: Support machine-default audiodev with fallback
Introduce machine property "audiodev"
audio: remove QEMU_AUDIO_* and -audio-help support
audio: simplify flow in audio_init
audio: commonize voice initialization
audio: return Error ** from audio_state_by_name
audio: allow returning an error from the driver init
audio: Require AudioState in AUD_add_capture
ui/vnc: Require audiodev= to enable audio
crypto: only include tls-cipher-suites in emulators
scsi-disk: ensure that FORMAT UNIT commands are terminated
esp: restrict non-DMA transfer length to that of available data
esp: use correct type for esp_dma_enable() in sysbus_esp_gpio_demux()
Makefile: build plugins before running TCG tests
meson: clean up static_library keyword arguments
make-release: do not ship dtc sources
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Many machine types have default audio devices with no way to set the underlying
audiodev. Instead of adding an option for each and every one of them, this new
property can be used as a default during machine initialisation when creating
such devices.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
[Make the property optional, instead of including it in all machines. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
this fixes numerous warnings of this type :
In file included from ../hw/ppc/spapr_pci.c:43:
../hw/ppc/spapr_pci.c: In function ‘spapr_dt_phb’:
../include/hw/ppc/fdt.h:18:13: warning: declaration of ‘ret’ shadows a previous local [-Wshadow=compatible-local]
18 | int ret = (exp); \
| ^~~
../hw/ppc/spapr_pci.c:2355:5: note: in expansion of macro ‘_FDT’
2355 | _FDT(bus_off = fdt_add_subnode(fdt, 0, phb->dtbusname));
| ^~~~
../hw/ppc/spapr_pci.c:2311:24: note: shadowed declaration is here
2311 | int bus_off, i, j, ret;
| ^~~
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230918145850.241074-2-clg@kaod.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
According to cxl_interleave_ways_enc(), fw->num_targets is allowed to be up
to 16. This also corresponds to CXL r3.0 spec. So, the fw->target_hbs[]
array is iterated from 0 to 15. But it is statically declared of length 8.
Thus, out of bound array access may occur.
Fixes: c28db9e000 ("hw/pci-bridge: Make PCIe and CXL PXB Devices inherit from TYPE_PXB_DEV")
Signed-off-by: Dmitry Frolov <frolov@swemel.ru>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Link: https://lore.kernel.org/r/20230913101055.754709-1-frolov@swemel.ru
Cc: qemu-stable@nongnu.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace the magic number 32 with CXL_RAS_ERR_HEADER_NUM for better code
readability and maintainability.
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
"Host Memory Backends" and "Memory devices" queue ("mem"):
- Support and document VM templating with R/O files using a new "rom"
parameter for memory-backend-file
- Some cleanups and fixes around NVDIMMs and R/O file handling for guest
RAM
- Optimize ioeventfd updates by skipping address spaces that are not
applicable
-----BEGIN PGP SIGNATURE-----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=iraT
-----END PGP SIGNATURE-----
Merge tag 'mem-2023-09-19' of https://github.com/davidhildenbrand/qemu into staging
Hi,
"Host Memory Backends" and "Memory devices" queue ("mem"):
- Support and document VM templating with R/O files using a new "rom"
parameter for memory-backend-file
- Some cleanups and fixes around NVDIMMs and R/O file handling for guest
RAM
- Optimize ioeventfd updates by skipping address spaces that are not
applicable
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEG9nKrXNcTDpGDfzKTd4Q9wD/g1oFAmUJdykRHGRhdmlkQHJl
# ZGhhdC5jb20ACgkQTd4Q9wD/g1pf2w//akOUoYMuamySGjXtKLVyMKZkjIys+Ama
# k2C0xzsWAHBP572ezwHi8uxf5j9kzAjsw6GxDZ7FAamD9MhiohkEvkecloBx6f/c
# q3fVHblBNkG7v2urtf4+6PJtJvhzOST2SFXfWeYhO/vaA04AYCDgexv82JN3gA6B
# OS8WyOX62b8wILPSY2GLZ8IqpE9XnOYZwzVBn6YB1yo7ZkYEfXO6cA8nykNuNcOE
# vppqDo7uVIX6317FWj8ygxmzFfOaj0WT2MT2XFzEIDfg8BInQN8HC4mTn0hcVKMa
# N1y+eZH733CQKT+uNBRZ5YOeljOi4d6gEEyvkkA/L7e5D3Qg9hIdvHb4uryCFSWX
# Vt07OP1XLBwCZFobOC6sg+2gtTZJxxYK89e6ZzEd0454S24w5bnEteRAaCGOP0XL
# ww9xYULqhtZs55UC4rvZHJwdUAk1fIY4VqynwkeQXegvz6BxedNeEkJiiEU0Tizx
# N2VpsxAJ7H/LLSFeZoCRESo4azrH6U4n7S/eS1tkCniFqibfe2yIQCDoJVfb42ec
# gfg/vThCrDwHkIHzkMmoV8NndA7Q7SIkyMfYeEEBeZMeg8JzYll4DJEw/jQCacxh
# KRUa+AZvGlTJUq0mkvyOVfLki+iaehoIUuY1yvMrmdWijPO8n3YybmP9Ljhr8VdR
# 9MSYZe+I2v8=
# =iraT
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 19 Sep 2023 06:25:45 EDT
# gpg: using RSA key 1BD9CAAD735C4C3A460DFCCA4DDE10F700FF835A
# gpg: issuer "david@redhat.com"
# gpg: Good signature from "David Hildenbrand <david@redhat.com>" [unknown]
# gpg: aka "David Hildenbrand <davidhildenbrand@gmail.com>" [full]
# gpg: aka "David Hildenbrand <hildenbr@in.tum.de>" [unknown]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 1BD9 CAAD 735C 4C3A 460D FCCA 4DDE 10F7 00FF 835A
* tag 'mem-2023-09-19' of https://github.com/davidhildenbrand/qemu:
memory: avoid updating ioeventfds for some address_space
machine: Improve error message when using default RAM backend id
softmmu/physmem: Hint that "readonly=on,rom=off" exists when opening file R/W for private mapping fails
docs: Start documenting VM templating
docs: Don't mention "-mem-path" in multi-process.rst
softmmu/physmem: Never return directories from file_ram_open()
softmmu/physmem: Fail creation of new files in file_ram_open() with readonly=true
softmmu/physmem: Bail out early in ram_block_discard_range() with readonly files
softmmu/physmem: Remap with proper protection in qemu_ram_remap()
backends/hostmem-file: Add "rom" property to support VM templating with R/O files
softmmu/physmem: Distinguish between file access mode and mmap protection
nvdimm: Reject writing label data to ROM instead of crashing QEMU
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In this short queue we're making two important changes:
- Nicholas Piggin is now the qemu-ppc maintainer. Cédric Le Goater and
Daniel Barboza will act as backup during Nick's transition to this new
role.
- Support for NVIDIA V100 GPU with NVLink2 is dropped from qemu-ppc.
Linux removed the same support back in 5.13, we're following suit now.
A xive Coverity fix is also included.
-----BEGIN PGP SIGNATURE-----
iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZQhPnBYcZGFuaWVsaGI0
MTNAZ21haWwuY29tAAoJEDzZypbeAzFk5QUBAJJNnCtv/SPP6bQVNGMgtfI9sz2z
MEttDa7SINyLCiVxAP0Y9z8ZHEj6vhztTX0AAv2QubCKWIVbJZbPV5RWrHCEBQ==
=y3nh
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20230918' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2023-09-18:
In this short queue we're making two important changes:
- Nicholas Piggin is now the qemu-ppc maintainer. Cédric Le Goater and
Daniel Barboza will act as backup during Nick's transition to this new
role.
- Support for NVIDIA V100 GPU with NVLink2 is dropped from qemu-ppc.
Linux removed the same support back in 5.13, we're following suit now.
A xive Coverity fix is also included.
# -----BEGIN PGP SIGNATURE-----
#
# iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZQhPnBYcZGFuaWVsaGI0
# MTNAZ21haWwuY29tAAoJEDzZypbeAzFk5QUBAJJNnCtv/SPP6bQVNGMgtfI9sz2z
# MEttDa7SINyLCiVxAP0Y9z8ZHEj6vhztTX0AAv2QubCKWIVbJZbPV5RWrHCEBQ==
# =y3nh
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 18 Sep 2023 09:24:44 EDT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20230918' of https://gitlab.com/danielhb/qemu:
spapr: Remove support for NVIDIA V100 GPU with NVLink2
ppc/xive: Fix uint32_t overflow
MAINTAINERS: Nick Piggin PPC maintainer, other PPC changes
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, when using a true R/O NVDIMM (ROM memory backend) with a label
area, the VM can easily crash QEMU by trying to write to the label area,
because the ROM memory is mmap'ed without PROT_WRITE.
[root@vm-0 ~]# ndctl disable-region region0
disabled 1 region
[root@vm-0 ~]# ndctl zero-labels nmem0
-> QEMU segfaults
Let's remember whether we have a ROM memory backend and properly
reject the write request:
[root@vm-0 ~]# ndctl disable-region region0
disabled 1 region
[root@vm-0 ~]# ndctl zero-labels nmem0
zeroed 0 nmem
In comparison, on a system with a R/W NVDIMM:
[root@vm-0 ~]# ndctl disable-region region0
disabled 1 region
[root@vm-0 ~]# ndctl zero-labels nmem0
zeroed 1 nmem
For ACPI, just return "unsupported", like if no label exists. For spapr,
return "H_P2", similar to when no label area exists.
Could we rely on the "unarmed" property? Maybe, but it looks cleaner to
only disallow what certainly cannot work.
After all "unarmed=on" primarily means: cannot accept persistent writes. In
theory, there might be setups where devices with "unarmed=on" set could
be used to host non-persistent data (temporary files, system RAM, ...); for
example, in Linux, admins can overwrite the "readonly" setting and still
write to the device -- which will work as long as we're not using ROM.
Allowing writing label data in such configurations can make sense.
Message-ID: <20230906120503.359863-2-david@redhat.com>
Fixes: dbd730e859 ("nvdimm: check -object memory-backend-file, readonly=on option")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
NVLink2 support was removed from the PPC PowerNV platform and VFIO in
Linux 5.13 with commits :
562d1e207d32 ("powerpc/powernv: remove the nvlink support")
b392a1989170 ("vfio/pci: remove vfio_pci_nvlink2")
This was 2.5 years ago. Do the same in QEMU with a revert of commit
ec132efaa8 ("spapr: Support NVIDIA V100 GPU with NVLink2"). Some
adjustements are required on the NUMA part.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20230918091717.149950-1-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Now that we defer address space update and tlb_flush until
the next async_run_on_cpu, the plugin run at the end of the
instruction no longer has to contend with a flushed tlb.
Therefore, delete SavedIOTLB entirely.
Properly return false from tlb_plugin_lookup when we do
not have a tlb match.
Fixes a bug in which SavedIOTLB had stale data, because
there were multiple i/o accesses within a single insn.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Small downtime optimisation for VFIO migration
* P2P support for VFIO migration
* Introduction of a save_prepare() handler to fail VFIO migration
* Fix on DMA logging ranges calculation for OVMF enabling dynamic window
-----BEGIN PGP SIGNATURE-----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=44e0
-----END PGP SIGNATURE-----
Merge tag 'pull-vfio-20230911' of https://github.com/legoater/qemu into staging
vfio queue:
* Small downtime optimisation for VFIO migration
* P2P support for VFIO migration
* Introduction of a save_prepare() handler to fail VFIO migration
* Fix on DMA logging ranges calculation for OVMF enabling dynamic window
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmT+uZQACgkQUaNDx8/7
# 7KGFSw//UIqSet6MUxZZh/t7yfNFUTnxx6iPdChC3BphBaDDh99FCQrw5mPZ8ImF
# 4rz0cIwSaHXraugEsC42TDaGjEmcAmYD0Crz+pSpLU21nKtYyWtZy6+9kyYslMNF
# bUq0UwD0RGTP+ZZi6GBy1hM30y/JbNAGeC6uX8kyJRuK5Korfzoa/X5h+B2XfouW
# 78G1mARHq5eOkGy91+rAJowdjqtkpKrzkfCJu83330Bb035qAT/PEzGs5LxdfTla
# ORNqWHy3W+d8ZBicBQ5vwrk6D5JIZWma7vdXJRhs1wGO615cuyt1L8nWLFr8klW5
# MJl+wM7DZ6UlSODq7r839GtSuWAnQc2j7JKc+iqZuBBk1v9fGXv2tZmtuTGkG2hN
# nYXSQfuq1igu1nGVdxJv6WorDxsK9wzLNO2ckrOcKTT28RFl8oCDNSPPTKpwmfb5
# i5RrGreeXXqRXIw0VHhq5EqpROLjAFwE9tkJndO8765Ag154plxssaKTUWo5wm7/
# kjQVuRuhs5nnMXfL9ixLZkwD1aFn5fWAIaR0psH5vGD0fnB1Pba+Ux9ZzHvxp5D8
# Kg3H6dKlht6VXdQ/qb0Up1LXCGEa70QM6Th2iO924ydZkkmqrSj+CFwGHvBsINa4
# 89fYd77nbRbdwWurj3JIznJYVipau2PmfbjZ/jTed4RxjBQ+fPA=
# =44e0
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 11 Sep 2023 02:54:12 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-vfio-20230911' of https://github.com/legoater/qemu:
vfio/common: Separate vfio-pci ranges
vfio/migration: Block VFIO migration with background snapshot
vfio/migration: Block VFIO migration with postcopy migration
migration: Add .save_prepare() handler to struct SaveVMHandlers
migration: Move more initializations to migrate_init()
vfio/migration: Fail adding device with enable-migration=on and existing blocker
migration: Add migration prefix to functions in target.c
vfio/migration: Allow migration of multiple P2P supporting devices
vfio/migration: Add P2P support for VFIO migration
vfio/migration: Refactor PRE_COPY and RUNNING state checks
qdev: Add qdev_add_vm_change_state_handler_full()
sysemu: Add prepare callback to struct VMChangeStateEntry
vfio/migration: Move from STOP_COPY to STOP in vfio_save_cleanup()
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move the PRE_COPY and RUNNING state checks to helper functions.
This is in preparation for adding P2P VFIO migration support, where
these helpers will also test for PRE_COPY_P2P and RUNNING_P2P states.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Connect the Configuration Frame controller (CFRAME_REG) and the
Configuration Frame broadcast controller (CFRAME_BCAST_REG) to the
Versal machine.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-9-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the Configuration Frame Unit (CFU_APB, CFU_FDRO and CFU_SFR) to
the Versal machine.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Acked-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-8-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame broadcast
controller (CFRAME_BCAST_REG).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-7-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame controller
(CFRAME_REG).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20230831165701.2016397-6-francisco.iglesias@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame Unit's Single
Frame Read port (CFU_SFR).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-5-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of Xilinx Versal's Configuration Frame Unit's data out
port (CFU_FDRO).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-4-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a model of the software programming interface (CFU_APB) of
Xilinx Versal's Configuration Frame Unit.
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230831165701.2016397-3-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the Xilinx Configuration Frame Interface (CFI) for transmitting
CFI data packets between the Xilinx Configuration Frame Unit models
(CFU_APB, CFU_FDRO and CFU_SFR), the Xilinx CFRAME controller (CFRAME_REG)
and the Xilinx CFRAME broadcast controller (CFRAME_BCAST_REG) models (when
emulating bitstream programming and readback).
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Acked-by: Edgar E. Iglesias <edgar@zeroasic.com>
Message-id: 20230831165701.2016397-2-francisco.iglesias@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Universal Flash Storage (UFS) is a high-performance mass storage device
with a serial interface. It is primarily used as a high-performance
data storage device for embedded applications.
This commit contains code for UFS device to be recognized
as a UFS PCI device.
Patches to handle UFS logical unit and Transfer Request will follow.
Signed-off-by: Jeuk Kim <jeuk20.kim@samsung.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 10232660d462ee5cd10cf673f1a9a1205fc8276c.1693980783.git.jeuk20.kim@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* debug facility improvements
* timebase and decrementer fixes
* record-replay fixes
* TCG fixes
* XIVE model improvements for multichip
-----BEGIN PGP SIGNATURE-----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=BUg6
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20230906' of https://github.com/legoater/qemu into staging
ppc queue :
* debug facility improvements
* timebase and decrementer fixes
* record-replay fixes
* TCG fixes
* XIVE model improvements for multichip
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmT4WKoACgkQUaNDx8/7
# 7KHjOg//bwENCptopnvX5XVTdGLRgBKoMWPkQhWPv4aHYz4t+bxHVWopdMU7i0aL
# hge+ZCCkMKsg2rADczbpWytAvC3vo1Pn4zZhZNQuEvYKIpiWVN6hSflmXWP/bN1I
# AGHlptKvNYKlPfGsmzZ2OZ2yItzrOwKFC/PnPSEc6dxjWfe9hEwzApxaAkOfX8wf
# C+oH8DPvFmh3PH3rI4psCn/xYtxAPW1zosBtgT7Ii1XreABMHLIfIpOmPPh1yF0d
# J7BgBdmxIvsN+syH/vh5jTtU4N/gQVorwyds9MX82Y3j0roxBVVLqH8rFjJA3Jsq
# c/g8WTi1hHiDd8G4m1JcLI1VAhsgh1KhqG9pDaSdQXhP0E4p8N/XjxOR5ro+KxM3
# Dz/Q77VoEKuat+AXg71kc68i11CninhTVSyGnjI80ISWWYvHFQ2Sv8J9U6sS/d0m
# +fo6hed7DDgfXg4OMtedF4HMmc6JAfm9eBzHUoanaoIzX0vX6vetXeMfWh6iceYW
# KNcQuUi3Pvvh/AjE36jusqTkbTleP5Yo4OKNJz4pEP4sU2wQPYU32Lo7Kg7p4WPA
# j+emWmWX4gcn9zTvm2LPYwkdgQ5HgigUJzq9i9qlMqfOOCpRwAsE7V0KxyV0NwDT
# cAAOBCdNm4t94Ni3KEING7xuDzERvJ7H2D6uRQjVsre8cMUO0QE=
# =BUg6
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 06 Sep 2023 06:47:06 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-ppc-20230906' of https://github.com/legoater/qemu: (35 commits)
ppc/xive: Add support for the PC MMIOs
ppc/xive: Handle END triggers between chips with MMIOs
ppc/xive: Introduce a new XiveRouter end_notify() handler
ppc/xive: Use address_space routines to access the machine RAM
target/ppc: Fix the order of kvm_enable judgment about kvmppc_set_interrupt()
hw/ppc/e500: fix broken snapshot replay
target/ppc: Flush inputs to zero with NJ in ppc_store_vscr
target/ppc: Fix LQ, STQ register-pair order for big-endian
tests/avocado: ppc64 reverse debugging tests for pseries and powernv
tests/avocado: reverse-debugging cope with re-executing breakpoints
tests/avocado: boot ppc64 pseries replay-record test to Linux VFS mount
spapr: Fix record-replay machine reset consuming too many events
spapr: Fix machine reset deadlock from replay-record
target/ppc: Fix timebase reset with record-replay
target/ppc: Fix CPU reservation migration for record-replay
hw/ppc: Read time only once to perform decrementer write
hw/ppc: Reset timebase facilities on machine reset
target/ppc: Migrate DECR SPR
hw/ppc: Always store the decrementer value
target/ppc: Sign-extend large decrementer to 64-bits
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmTxsaQACgkQUaNDx8/7
7KGXmg//XJNisscl/VWSBaGmH5MbQUAg/QCRalXx1V/lJ8rhE/JqwnWKuoPFd4EN
iDlh3ufpzxPhHFc9boechuM5ytlrJxpLJoCIJ4sw/4qnO3Dy3Q6BCy1t8Ma62D1u
oE7cAMHsriJ1uTJNHUTFo72VapTaH2XwFN9lFDuQW45d+WWAXtVJsqvRgFETNmw6
YYnTTpH2gLTZZFEgOixhWpGLh4Ibc/l8U1VzL0ctQmC11xng0bqk3PAqU9NGzcM5
MJmEGAxg43CnFu9NJI1nMqC/coi/8PFtrM7HprSwE3H8Jkwncs4ePVT+kZQC+VNQ
7EaVkksfEGHlN8XP5+eQDrQ5yT6ve+fbHTLQhwULfeyt0GlQ8h1yewvHCDWo/zw3
XI1ZyOcNZ2yiaenSUrTPzu0LiqZEJQnzRjPCpgTi1fU08ryEMEaPtr176YDLCguQ
cpRj4QSZHCrGl/Eo9NlkFP/2rQDKTvCcedKPkYLQtsurSiH/36Oj9YvZycNtZ574
ortKAtru4YV/rglNX4L8JDhdI+nqvy1liifpJsiS/2KBZDpVFaP8PzGIV40HNy3G
8/LVTnaggZaScF3ftHhkg84uQumELS9l2dhsNCL9HqdlrNXLQrVAIR6iuQlpOKBa
5S/6h7ZXGOb1qNVQjYp4HCrB7X1KIJYksZ3GdUREf8ot5Ds1FhE=
=ymmX
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu into staging
aspeed queue:
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmTxsaQACgkQUaNDx8/7
# 7KGXmg//XJNisscl/VWSBaGmH5MbQUAg/QCRalXx1V/lJ8rhE/JqwnWKuoPFd4EN
# iDlh3ufpzxPhHFc9boechuM5ytlrJxpLJoCIJ4sw/4qnO3Dy3Q6BCy1t8Ma62D1u
# oE7cAMHsriJ1uTJNHUTFo72VapTaH2XwFN9lFDuQW45d+WWAXtVJsqvRgFETNmw6
# YYnTTpH2gLTZZFEgOixhWpGLh4Ibc/l8U1VzL0ctQmC11xng0bqk3PAqU9NGzcM5
# MJmEGAxg43CnFu9NJI1nMqC/coi/8PFtrM7HprSwE3H8Jkwncs4ePVT+kZQC+VNQ
# 7EaVkksfEGHlN8XP5+eQDrQ5yT6ve+fbHTLQhwULfeyt0GlQ8h1yewvHCDWo/zw3
# XI1ZyOcNZ2yiaenSUrTPzu0LiqZEJQnzRjPCpgTi1fU08ryEMEaPtr176YDLCguQ
# cpRj4QSZHCrGl/Eo9NlkFP/2rQDKTvCcedKPkYLQtsurSiH/36Oj9YvZycNtZ574
# ortKAtru4YV/rglNX4L8JDhdI+nqvy1liifpJsiS/2KBZDpVFaP8PzGIV40HNy3G
# 8/LVTnaggZaScF3ftHhkg84uQumELS9l2dhsNCL9HqdlrNXLQrVAIR6iuQlpOKBa
# 5S/6h7ZXGOb1qNVQjYp4HCrB7X1KIJYksZ3GdUREf8ot5Ds1FhE=
# =ymmX
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 01 Sep 2023 05:40:52 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu: (26 commits)
hw/sd: Introduce a "sd-card" SPI variant model
hw/sd: Add sd_cmd_SET_BLOCK_COUNT() handler
hw/sd: Add sd_cmd_SEND_TUNING_BLOCK() handler
hw/sd: Add sd_cmd_SEND_RELATIVE_ADDR() handler
hw/sd: Add sd_cmd_ALL_SEND_CID() handler
hw/sd: Add sd_cmd_SEND_OP_CMD() handler
hw/sd: Add sd_cmd_GO_IDLE_STATE() handler
hw/sd: Add sd_cmd_unimplemented() handler
hw/sd: Add sd_cmd_illegal() handler
hw/sd: Introduce sd_cmd_handler type
hw/sd: Move proto_name to SDProto structure
hw/sd: When card is in wrong state, log which spec version is used
hw/sd: When card is in wrong state, log which state it is
hw/sd/sdcard: Return ILLEGAL for CMD19/CMD23 prior SD spec v3.01
aspeed: Get the BlockBackend of FMC0 from the flash device
m25p80: Introduce an helper to retrieve the BlockBackend of a device
aspeed: Create flash devices only when defaults are enabled
hw/ssi: Check for duplicate CS indexes
aspeed/smc: Wire CS lines at reset
hw/ssi: Introduce a ssi_get_cs() helper
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It will help us model the END triggers on the PowerNV machine, which
can be rerouted to another interrupt controller.
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
spapr_machine_reset gets a random number to populate the device-tree
rng seed with. When loading a snapshot for record-replay, the machine
is reset again, and that tries to consume the random event record
again, crashing due to inconsistent record
Fix this by saving the seed to populate the device tree with, and
skipping the rng on snapshot load.
Acked-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the machine is reset to load a new snapshot while being debugged
with replay-record, it is done from another thread, so the CPU does
not run the register setting operations. Set CPU registers directly in
machine reset.
Cc: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Lower interrupts, delete timers, and set time facility registers
back to initial state on machine reset.
This is not so important for record-replay since timebase and
decrementer are migrated, but it gives a cleaner reset state.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: checkpatch.pl fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and replace the SDState::spi attribute with a test checking the
SDProto array of commands.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Introduce a new structure to hold the bus protocol specific
fields: SDProto. The first field is the protocol name.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210624142209.1193073-4-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It will help in getting rid of some drive_get(IF_MTD) calls by
retrieving the BlockBackend directly from the m25p80 device.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Simple routine to retrieve a DeviceState object on a SPI bus using its
CS index. It will be useful for the board to wire the CS lines.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Boards will use this new property to identify the device CS line and
wire the SPI controllers accordingly.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Added support for the buffer organization option in pool buffer control
register.when set to 1,The buffer is split into two parts: Lower 16 bytes
for Tx and higher 16 bytes for Rx.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Fixed inconsistency between the regisiter bit field definition header file
and the ast2600 datasheet. The reg name is I2CD1C:Pool Buffer Control
Register in old register mode and I2CC0C: Master/Slave Pool Buffer Control
Register in new register mode. They share bit field
[12:8]:Transmit Data Byte Count and bit field
[29:24]:Actual Received Pool Buffer Size according to the datasheet.
According to the ast2600 datasheet,the actual Tx count is
Transmit Data Byte Count plus 1, and the max Rx size is
Receive Pool Buffer Size plus 1, both in Pool Buffer Control Register.
The version before forgot to plus 1, and mistake Rx count for Rx size.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 3be3d6ccf2 ("aspeed: i2c: Migrate to registerfields API")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
kvmclock_create() is only implemented in hw/i386/kvm/clock.h.
Restrict the "hw/kvm/clock.h" header to i386 by moving it to
hw/i386/.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230620083228.88796-3-philmd@linaro.org>
We shouldn't call kvmclock_create() when KVM is not available
or disabled:
- check for kvm_enabled() before calling it
- assert KVM is enabled once called
Since the call is elided when KVM is not available, we can
remove the stub (it is never compiled).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230620083228.88796-2-philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-14-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
By default, C function prototypes declared in headers are visible,
so there is no need to declare them as 'extern' functions.
Remove this redundancy in a single bulk commit; do not modify:
- meson.build (used to check function availability at runtime)
- pc-bios/
- libdecnumber/
- tests/
- *.c
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230605175647.88395-5-philmd@linaro.org>
HAX is deprecated since commits 73741fda6c ("MAINTAINERS: Abort
HAXM maintenance") and 90c167a1da ("docs/about/deprecated: Mark
HAXM in QEMU as deprecated"), released in v8.0.0.
Per the latest HAXM release (v7.8 [*]), the latest QEMU supported
is v7.2:
Note: Up to this release, HAXM supports QEMU from 2.9.0 to 7.2.0.
The next commit (https://github.com/intel/haxm/commit/da1b8ec072)
added:
HAXM v7.8.0 is our last release and we will not accept
pull requests or respond to issues after this.
It became very hard to build and test HAXM. Its previous
maintainers made it clear they won't help. It doesn't seem to be
a very good use of QEMU maintainers to spend their time in a dead
project. Save our time by removing this orphan zombie code.
[*] https://github.com/intel/haxm/releases/tag/v7.8.0
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230831082016.60885-1-philmd@linaro.org>
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
-----BEGIN PGP SIGNATURE-----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=MFh3
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmTwbukZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3ihBD/wK8Iz0KpTAwZBDAodnSZrh
# tQnJAvYFp8CxA4O8sZ9IeWsZh90gzsTCZi0NqUTTzvWCJfxkB7qTPdlJT5IzVxou
# oEUk2aogSJhRA3XRJzqArXsPlnZGSYDbtwKx4VtfCvOCCH08Y7nhnFaRj1oFnR4Q
# 0PE/8YtGXTBxLHrO8U3tomg7zElzOUP8ZVZtb30BOyw1jtfSD03IZR8dzpA43u1E
# Hh418WvVekmwFoFNh8yUeHzbyXMZufzvbJPuDGJ8pPWwIpvSG6chOnKF8jZll+Ur
# DqOsDkGlQgcBR2QwYfSPClrEkX8yahJ95PBfM6giG+DQC7OiElqXqTiUGZcpgUVo
# uSUbzS4YPsxCnyVV6SBXV+f/8hdXBxOSHTgl7OAFa8X9OwWwspxHJ/v2o/2ibnUT
# hTTkFp/w1nQwVEN8xf1DOUpm/J2Wr8UeH4f776daSrfKAol2BKbHb8dOgGLQCwqb
# G+iDcE4bkzRqly6f+uVk8xSEZDd9P1NYoxKV+gNlV1dTspdHVpTC+rXMa8dRw5hI
# 4KgaAslj++Xa229xkjORXCJ1cICRIebYg7+SjvTtGBYsFV7plsCcYb/R9yLmhVCf
# fKHKKaYe9sQJ82apOIkTc+nnW8BQQx6XUmU/A//iZ8JGLk6DpJcZ8f1m/2rVZTsl
# 9+lsmpBf4w+uR4o+Womhfw==
# =MFh3
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 31 Aug 2023 06:43:53 EDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm: (24 commits)
hw/arm: Set number of MPU regions correctly for an505, an521, an524
hw/arm/armv7m: Add mpu-ns-regions and mpu-s-regions properties
target/arm: Do all "ARM_FEATURE_X implies Y" checks in post_init
rtc: Use time_t for passing and returning time offsets
hw/rtc/aspeed_rtc: Use 64-bit offset for holding time_t difference
hw/rtc/twl92230: Use int64_t for sec_offset and alm_sec
hw/rtc/m48t59: Use 64-bit arithmetic in set_alarm()
target/arm: Catch illegal-exception-return from EL3 with bad NSE/NS
Add i.MX7 SRC device implementation
Add i.MX7 missing TZ devices and memory regions
Refactor i.MX7 processor code
Add i.MX6UL missing devices.
Refactor i.MX6UL processor code
Remove i.MX7 IOMUX GPR device from i.MX6UL
target/arm: properly document FEAT_CRC32
target/arm: Implement FEAT_HPDS2 as a no-op
target/arm: Suppress FEAT_TRBE (Trace Buffer Extension)
target/arm: Apply access checks to neoverse-v1 special registers
target/arm: Apply access checks to neoverse-n1 special registers
target/arm: Introduce make_ccsidr64
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The IoTKit, SSE200 and SSE300 all default to 8 MPU regions. The
MPS2/MPS3 FPGA images don't override these except in the case of
AN547, which uses 16 MPU regions.
Define properties on the ARMSSE object for the MPU regions (using the
same names as the documented RTL configuration settings, and
following the pattern we already have for this device of using
all-caps names as the RTL does), and set them in the board code.
We don't actually need to override the default except on AN547,
but it's simpler code to have the board code set them always
rather than tracking which board subtypes want to set them to
a non-default value separately from what that value is.
Tho overall effect is that for mps2-an505, mps2-an521 and mps3-an524
we now correctly use 8 MPU regions, while mps3-an547 stays at its
current 16 regions.
It's possible some guest code wrongly depended on the previous
incorrectly modeled number of memory regions. (Such guest code
should ideally check the number of regions via the MPU_TYPE
register.) The old behaviour can be obtained with additional
-global arguments to QEMU:
For mps2-an521 and mps2-an524:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16 -global sse-200.CPU1_MPU_NS=16 -global sse-200.CPU1_MPU_S=16
For mps2-an505:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16
NB that the way the implementation allows this use of -global
is slightly fragile: if the board code explicitly sets the
properties on the sse-200 object, this overrides the -global
command line option. So we rely on:
- the boards that need fixing all happen to use the SSE defaults
- we can write the board code to only set the property if it
is different from the default, rather than having all boards
explicitly set the property
- the board that does need to use a non-default value happens
to need to set it to the same value (16) we previously used
This works, but there are some kinds of refactoring of the
mps2-tz.c code that would break the support for -global here.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1772
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-4-peter.maydell@linaro.org
M-profile CPUs generally allow configuration of the number of MPU
regions that they have. We don't currently model this, so our
implementations of some of the board models provide CPUs with the
wrong number of regions. RTOSes like Zephyr that hardcode the
expected number of regions may therefore not run on the model if they
are set up to run on real hardware.
Add properties mpu-ns-regions and mpu-s-regions to the ARMV7M object,
matching the ability of hardware to configure the number of Secure
and NonSecure regions separately. Our actual CPU implementation
doesn't currently support that, and it happens that none of the MPS
boards we model set the number of regions differently for Secure vs
NonSecure, so we provide an interface to the boards and SoCs that
won't need to change if we ever do add that functionality in future,
but make it an error to configure the two properties to different
values.
(The property name on the CPU is the somewhat misnamed-for-M-profile
"pmsav7-dregion", so we don't follow that naming convention for
the properties here. The TRM doesn't say what the CPU configuration
variable names are, so we pick something, and follow the lowercase
convention we already have for properties here.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-3-peter.maydell@linaro.org
In the aspeed_rtc device we store a difference between two time_t
values in an 'int'. This is not really correct when time_t could
be 64 bits. Enlarge the field to 'int64_t'.
This is a migration compatibility break for the aspeed boards.
While we are changing the vmstate, remove the accidental
duplicate of the offset field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The SRC device is normally used to start the secondary CPU.
When running Linux directly, QEMU is emulating a PSCI interface that UBOOT
is installing at boot time and therefore the fact that the SRC device is
unimplemented is hidden as Qemu respond directly to PSCI requets without
using the SRC device.
But if you try to run a more bare metal application (maybe uboot itself),
then it is not possible to start the secondary CPU as the SRC is an
unimplemented device.
This patch adds the ability to start the secondary CPU through the SRC
device so that you can use this feature in bare metal applications.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ce9a0162defd2acee5dc7f8a674743de0cded569.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add various memory segments
- OCRAM
- OCRAM EPDC
- OCRAM PXP
- OCRAM S
- ROM
- CAAM
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: f887a3483996ba06d40bd62ffdfb0ecf68621987.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for all i.MX7 devices in i.MX7 header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 59e195d33e4d486a8d131392acd46633c8c10ed7.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add 4 missing PWM devices
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 59e4dc56e14eccfefd379275ec19048dff9c10b3.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for most i.MX6UL devices in i.MX6UL header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: d579043fbd4e4b490370783fda43fc02c8e9be75.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
i.MX7 IOMUX GPR device is not equivalent to i.MX6UL IOMUXC GPR device.
In particular, register 22 is not present on i.MX6UL and this is actualy
The only register that is really emulated in the i.MX7 IOMUX GPR device.
Note: The i.MX6UL code is actually also implementing the IOMUX GPR device
as an unimplemented device at the same bus adress and the 2 instantiations
were actualy colliding. So we go back to the unimplemented device for now.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 48681bf51ee97646479bb261bee19abebbc8074e.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to use virtio backends we need to initialize RAM for the
xen-mapcache (which is responsible for mapping guest memory using foreign
mapping) to work. Calculate and add hi/low memory regions based on
machine->ram_size.
Use the constants defined in public header arch-arm.h to be aligned with the xen
toolstack.
While using this machine, the toolstack should then pass real ram_size using
"-m" arg. If "-m" is not given, create a QEMU machine without IOREQ and other
emulated devices like TPM and VIRTIO. This is done to keep this QEMU machine
usable for /etc/init.d/xencommons.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
In order to use virtio backends we need to allocate virtio-mmio
parameters (irq and base) and register corresponding buses.
Use the constants defined in public header arch-arm.h to be
aligned with the toolstack. So the number of current supported
virtio-mmio devices is 10.
For the interrupts triggering use already existing on Arm
device-model hypercall.
The toolstack should then insert the same amount of device nodes
into guest device-tree.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Using "-device virtio-gpu,blob=true" currently does not work on big
endian hosts (like s390x). The guest kernel prints an error message
like:
[drm:virtio_gpu_dequeue_ctrl_func [virtio_gpu]] *ERROR* response 0x1200 (command 0x10c)
and the display stays black. When running QEMU with "-d guest_errors",
it shows an error message like this:
virtio_gpu_create_mapping_iov: nr_entries is too big (83886080 > 16384)
which indicates that this value has not been properly byte-swapped.
And indeed, the virtio_gpu_create_blob_bswap() function (that should
swap the fields in the related structure) fails to swap some of the
entries. After correctly swapping all missing values here, too, the
virtio-gpu device is now also working with blob=true on s390x hosts.
Fixes: e0933d91b1 ("virtio-gpu: Add virtio_gpu_resource_create_blob")
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2230469
Message-Id: <20230815122007.928049-1-thuth@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Implement nRF51 DETECT signal in the GPIO peripheral.
The reference manual makes mention of a per-pin DETECT signal, but these
are not exposed to the user. See https://devzone.nordicsemi.com/f/nordic-q-a/39858/gpio-per-pin-detect-signal-available
for more information. Currently, I don't see a reason to model these.
Signed-off-by: Chris Laplante <chris@laplante.io>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230728160324.1159090-2-chris@laplante.io
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Calling OpenGL from different threads can have bad consequences if not
carefully reviewed. It's not generally supported. In my case, I was
debugging a crash in glDeleteTextures from OPENGL32.DLL, where I asked
qemu for gl=es, and thus ANGLE implementation was expected. libepoxy did
resolution of the global pointer for glGenTexture to the GLES version
from the main thread. But it resolved glDeleteTextures to the GL
version, because it was done from a different thread without correct
context. Oops.
Let's stick to the main thread for GL calls by using a BH.
Note: I didn't use atomics for reset_finished check, assuming the BQL
will provide enough of sync, but I might be wrong.
Acked-by: Dongwon Kim <dongwon.kim@intel.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230726173929.690601-3-marcandre.lureau@redhat.com>
The first bitfield here is supposed to be used as a 64-bit equivalent
to the "uint64_t msi_addr" in the union. To make this work correctly
on big endian hosts, too, the __addr_hi field has to be part of the
bitfield, and the the bitfield members must be declared with "uint64_t"
instead of "uint32_t" - otherwise the values are placed in the wrong
bytes on big endian hosts.
Same applies to the 32-bit "msi_data" field: __resved1 must be part
of the bitfield, and the members must be declared with "uint32_t"
instead of "uint16_t".
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-7-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The code already tries to do some endianness handling here, but
currently fails badly:
- While it already swaps the data when logging errors / tracing, it fails
to byteswap the value before e.g. accessing entry->irte.present
- entry->irte.source_id is swapped with le32_to_cpu(), though this is
a 16-bit value
- The whole union is apparently supposed to be swapped via the 64-bit
data[2] array, but the struct is a mixture between 32 bit values
(the first 8 bytes) and 64 bit values (the second 8 bytes), so this
cannot work as expected.
Fix it by converting the struct to two proper 64-bit bitfields, and
by swapping the values only once for everybody right after reading
the data from memory.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230802135723.178083-3-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The QEMU CI fails in virtio-scmi test occasionally. As reported by
Thomas Huth, this happens most likely when the system is loaded and it
fails with the following error:
qemu-system-aarch64: ../../devel/qemu/hw/pci/msix.c:659:
msix_unset_vector_notifiers: Assertion `dev->msix_vector_use_notifier && dev->msix_vector_release_notifier' failed.
../../devel/qemu/tests/qtest/libqtest.c:200: kill_qemu() detected QEMU death from signal 6 (Aborted) (core dumped)
As discovered by Fabiano Rosas, the cause is a duplicate invocation of
msix_unset_vector_notifiers via duplicate vu_scmi_stop calls:
msix_unset_vector_notifiers
virtio_pci_set_guest_notifiers
vu_scmi_stop
vu_scmi_disconnect
...
qemu_chr_write_buffer
msix_unset_vector_notifiers
virtio_pci_set_guest_notifiers
vu_scmi_stop
vu_scmi_set_status
...
qemu_cleanup
While vu_scmi_stop calls are protected by vhost_dev_is_started()
check, it's apparently not enough. vhost-user-blk and vhost-user-gpio
use an extra protection, see f5b22d06fb (vhost: recheck dev state in
the vhost_migration_log routine) for the motivation. Let's use the
same in vhost-user-scmi, which fixes the failure above.
Fixes: a5dab090e1 ("hw/virtio: Add boilerplate for vhost-user-scmi device")
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Message-Id: <20230720101037.2161450-1-mzamazal@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Coverity points out (CID 1513106, 1513107) that MemoryListener is a
192 byte struct which we are passing around by value. Switch to
passing a const pointer into xen_register_ioreq() and then to
xen_do_ioreq_register(). We can also make the file-scope
MemoryListener variables const, since nothing changes them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230718101057.1110979-1-peter.maydell@linaro.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Commit 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs") split
calls to scsi_req_new() and scsi_req_enqueue() in the virtio-scsi device.
No ill effects were observed until commit 8cc5583abe ("virtio-scsi: Send
"REPORTED LUNS CHANGED" sense data upon disk hotplug events") added a
unit attention that was easy to trigger with device hotplug and
hot-unplug.
Because the two calls were separated, all requests in the batch were
prepared calling scsi_req_new() to report a sense. The first one
submitted would report the right sense and reset it to NO_SENSE, while
the others reported CHECK_CONDITION with no sense data. This caused
SCSI errors in Linux.
To solve this issue, let's fetch the unit attention as early as possible
when we prepare the request, so that only the first request in the batch
will use the unit attention SCSIReqOps and the others will not report
CHECK CONDITION.
Fixes: 1880ad4f4e ("virtio-scsi: Batched prepare for cmd reqs")
Fixes: 8cc5583abe ("virtio-scsi: Send "REPORTED LUNS CHANGED" sense data upon disk hotplug events")
Reported-by: Thomas Huth <thuth@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2176702
Co-developed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-ID: <20230712134352.118655-2-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In many cases, blindly unplugging a virtio-mem device is problematic. We
can only safely remove a device once:
* The guest is not expecting to be able to read unplugged memory
(unplugged-inaccessible == on)
* The virtio-mem device does not have memory plugged (size == 0)
* The virtio-mem device does not have outstanding requests to the VM to
plug memory (requested-size == 0)
So let's add a callback to the virtio-mem device class to check for that.
We'll wire-up virtio-mem-pci next.
Message-ID: <20230711153445.514112-7-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's support unplug requests for virtio-md-pci devices that provide
a unplug_request_check() callback.
We'll wire that up for virtio-mem-pci next.
Message-ID: <20230711153445.514112-6-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's factor out (un)plug handling, to be reused from arm/virt code.
Provide stubs for the case that CONFIG_VIRTIO_MD is not selected because
neither virtio-mem nor virtio-pmem is enabled. While this cannot
currently happen for x86, it will be possible for arm/virt.
Message-ID: <20230711153445.514112-3-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's add a new abstract "virtio memory device" type, and use it as
parent class of virtio-mem-pci and virtio-pmem-pci.
Message-ID: <20230711153445.514112-2-david@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's avoid iterating over all devices and simply track it in the
DeviceMemoryState.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-11-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
There are no remaining users in the tree. Libvirt never used that
property and a quick internet search revealed no other users.
Further, we renamed that property already in commit f2ffbe2b7d
("pc: rename "hotplug memory" terminology to "device memory"") without
anybody complaining.
So let's just get rid of it.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-9-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Let's intrduce a new helper that we will use to replace existing memory
device setup code during machine initialization. We'll enforce that the
size has to be > 0.
Once all machines were converted, we'll only allocate ms->device_memory
if the size > 0.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20230623124553.400585-3-david@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
vhost-user-gpu: edid
vhost-user-scmi device
vhost-vdpa: _F_CTRL_RX and _F_CTRL_RX_EXTRA support for svq
cleanups, fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmSsjYMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp2vYH/20u6TAMssE/UAJoUU0ypbJkbHjDqiqDeuZN
qDYazLUWIJTUbDnSfXAiRcdJuukEpEFcoHa9O6vgFE/SNod51IrvsJR9CbZxNmk6
D+Px9dkMckDE/yb8f6hhcHsi7/1v04I0oSXmJTVYxWSKQhD4Km6x8Larqsh0u4yd
n6laZ+VK5H8sk6QvI5vMz+lYavACQVryiWV/GAigP21B0eQK79I5/N6y0q8/axD5
cpeTzUF+m33SfLfyd7PPmibCQFYrHDwosynSnr3qnKusPRJt2FzWkzOiZgbtgE2L
UQ/S4sYTBy8dZJMc0wTywbs1bSwzNrkQ+uS0v74z9wCUYTgvQTA=
=RsOh
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
pc,pci,virtio: cleanups, fixes, features
vhost-user-gpu: edid
vhost-user-scmi device
vhost-vdpa: _F_CTRL_RX and _F_CTRL_RX_EXTRA support for svq
cleanups, fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmSsjYMPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp2vYH/20u6TAMssE/UAJoUU0ypbJkbHjDqiqDeuZN
# qDYazLUWIJTUbDnSfXAiRcdJuukEpEFcoHa9O6vgFE/SNod51IrvsJR9CbZxNmk6
# D+Px9dkMckDE/yb8f6hhcHsi7/1v04I0oSXmJTVYxWSKQhD4Km6x8Larqsh0u4yd
# n6laZ+VK5H8sk6QvI5vMz+lYavACQVryiWV/GAigP21B0eQK79I5/N6y0q8/axD5
# cpeTzUF+m33SfLfyd7PPmibCQFYrHDwosynSnr3qnKusPRJt2FzWkzOiZgbtgE2L
# UQ/S4sYTBy8dZJMc0wTywbs1bSwzNrkQ+uS0v74z9wCUYTgvQTA=
# =RsOh
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 11 Jul 2023 12:00:19 AM BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (66 commits)
vdpa: Allow VIRTIO_NET_F_CTRL_RX_EXTRA in SVQ
vdpa: Restore packet receive filtering state relative with _F_CTRL_RX_EXTRA feature
vdpa: Allow VIRTIO_NET_F_CTRL_RX in SVQ
vdpa: Avoid forwarding large CVQ command failures
vdpa: Accessing CVQ header through its structure
vhost: Fix false positive out-of-bounds
vdpa: Restore packet receive filtering state relative with _F_CTRL_RX feature
vdpa: Restore MAC address filtering state
vdpa: Use iovec for vhost_vdpa_net_load_cmd()
pcie: Specify 0 for ARI next function numbers
pcie: Use common ARI next function number
include/hw/virtio: document some more usage of notifiers
include/hw/virtio: add kerneldoc for virtio_init
include/hw/virtio: document virtio_notify_config
hw/virtio: fix typo in VIRTIO_CONFIG_IRQ_IDX comments
include/hw: document the device_class_set_parent_* fns
include: attempt to document device_class_set_props
vdpa: Fix possible use-after-free for VirtQueueElement
pcie: Add hotplug detect state register to cmask
virtio-iommu: Rework the traces in virtio_iommu_set_page_size_mask()
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The current implementers of ARI are all SR-IOV devices. The ARI next
function number field is undefined for VF according to PCI Express Base
Specification Revision 5.0 Version 1.0 section 9.3.7.7. The PF still
requires some defined value so end the linked list formed with the field
by specifying 0 as required for any ARI implementation according to
section 7.8.7.2.
For migration, the field will keep having 1 as its value on the old
QEMU machine versions.
Fixes: 2503461691 ("pcie: Add some SR/IOV API documentation in docs/pcie_sriov.txt")
Fixes: 44c2c09488 ("hw/nvme: Add support for SR-IOV")
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20230710153838.33917-3-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the only implementers of ARI is SR-IOV devices, and they
behave similar. Share the ARI next function number.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20230710153838.33917-2-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Lets document some more of the core VirtIODevice structure.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-7-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-6-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-5-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These are useful functions for when you want proper inheritance of
functionality across realize/unrealize calls.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-3-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I'm still not sure how I achieve by use case of the parent class
defining the following properties:
static Property vud_properties[] = {
DEFINE_PROP_CHR("chardev", VHostUserDevice, chardev),
DEFINE_PROP_UINT16("id", VHostUserDevice, id, 0),
DEFINE_PROP_UINT32("num_vqs", VHostUserDevice, num_vqs, 1),
DEFINE_PROP_END_OF_LIST(),
};
But for the specialisation of the class I want the id to default to
the actual device id, e.g.:
static Property vu_rng_properties[] = {
DEFINE_PROP_UINT16("id", VHostUserDevice, id, VIRTIO_ID_RNG),
DEFINE_PROP_UINT32("num_vqs", VHostUserDevice, num_vqs, 1),
DEFINE_PROP_END_OF_LIST(),
};
And so far the API for doing that isn't super clear.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-2-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When running on a 64kB page size host and protecting a VFIO device
with the virtio-iommu, qemu crashes with this kind of message:
qemu-kvm: virtio-iommu page mask 0xfffffffffffff000 is incompatible
with mask 0x20010000
qemu: hardware error: vfio: DMA mapping failed, unable to continue
This is due to the fact the IOMMU MR corresponding to the VFIO device
is enabled very late on domain attach, after the machine init.
The device reports a minimal 64kB page size but it is too late to be
applied. virtio_iommu_set_page_size_mask() fails and this causes
vfio_listener_region_add() to end up with hw_error();
To work around this issue, we transiently enable the IOMMU MR on
machine init to collect the page size requirements and then restore
the bypass state.
Fixes: 90519b9053 ("virtio-iommu: Add bypass mode support to assigned device")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20230705165118.28194-2-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
There is also pci_new() which creates non-multifunction PCI devices.
Accordingly the parameter is always set to true when a multi function PCI
device is to be created.
The reason for the parameter's existence seems to be that it is used in the
internal PCI code as well which is the only location where it gets set to
false. This one usage can be resolved by factoring out an internal helper
function.
Remove this redundant, error-prone parameter.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230304114043.121024-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Every TYPE_PCI_IDE device performs the same not-so-trivial bit manipulation by
copy'n'paste code. Extract this into bmdma_status_writeb(), mirroring
bmdma_cmd_writeb().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20230531211043.41724-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Now that via_isa_set_irq() is unused it can be removed.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
* Use xl instead of mxl for disassemble
* Factor out extension tests to cpu_cfg.h
* disas/riscv: Add vendor extension support
* disas/riscv: Add support for XVentanaCondOps
* disas/riscv: Add support for XThead* instructions
* Fix mstatus related problems
* Fix veyron-v1 CPU properties
* Fix the xlen for data address when MPRV=1
* opensbi: Upgrade from v1.2 to v1.3
* Enable 32-bit Spike OpenSBI boot testing
* Support the watchdog timer of HiFive 1 rev b
* Only build qemu-system-riscv$$ on rv$$ host
* Add RVV registers to log
* Restrict ACLINT to TCG
* Add syscall riscv_hwprobe
* Add support for BF16 extensions
* KVM_RISCV_SET_TIMER macro is not configured correctly
* Generate devicetree only after machine initialization is complete
* virt: Convert fdt_load_addr to uint64_t
* KVM: fixes and enhancements
* Add support for the Zfa extension
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmSr+ekACgkQr3yVEwxT
gBMMGg//ZCcyH3KXB49c2KUIFO6FKYUxN9uC3giZCtuGyEH8T2yDgZVVXnxwU+Ij
+3Ej6T/ZdWMpePC9qf+xKzHWZk7Qc8Tcg+JgQbga573894yZInRwYl8HsSlEKA+Z
vlqSBPxTlp9rlDwGP/LjGljyIFqL4konk9zi3FL4ZXTF1iHUGrh/953Y3wIreEfl
KX5UznnWcgy2BqQT1vihMbM8qCVK6iryH+QZ6LiAsPMSX1rIzk8ectQryILzoIYh
bMiwCLVMyr4ZrUXjmGTF+7/WcOWwhhyfpdstf2iotKALelZtVHit0wHcty2GYQde
nvN83jJWu04DGXkPBUsqCUQXczGo1QHjJUH3RIRJzfOby/lGt4pSzHAfKA+iNUht
ikM3SdBsXMO+ogjTtTcCMb7/m2vsMoQP60VRts9Mh3YVD0cgr7RqpqRoEMugVYnr
ca8Vijf71mB+y+pq477eV1Q8BoKpr8xa1OlFkNKPC17uMD7HoDMI44QgFOgtYp10
TMsqqyB75q6PZhSEwm63xbmH0Zpo8kSqT/E3MTtGTyPeuL8TNNNSkCmFaGYmRrbI
XEp7vG2RaDJOvDomS3nUhA5ruc8SaXd0q25q2gLYQfCsehfFqZAwuNB5xf1zS0M0
ov1/gwaqU93t6nLbo2cCbb0plkIFKwwJ9KKjD06wJ4KPe0TGFzk=
=3XFD
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230710-1' of https://github.com/alistair23/qemu into staging
Third RISC-V PR for 8.1
* Use xl instead of mxl for disassemble
* Factor out extension tests to cpu_cfg.h
* disas/riscv: Add vendor extension support
* disas/riscv: Add support for XVentanaCondOps
* disas/riscv: Add support for XThead* instructions
* Fix mstatus related problems
* Fix veyron-v1 CPU properties
* Fix the xlen for data address when MPRV=1
* opensbi: Upgrade from v1.2 to v1.3
* Enable 32-bit Spike OpenSBI boot testing
* Support the watchdog timer of HiFive 1 rev b
* Only build qemu-system-riscv$$ on rv$$ host
* Add RVV registers to log
* Restrict ACLINT to TCG
* Add syscall riscv_hwprobe
* Add support for BF16 extensions
* KVM_RISCV_SET_TIMER macro is not configured correctly
* Generate devicetree only after machine initialization is complete
* virt: Convert fdt_load_addr to uint64_t
* KVM: fixes and enhancements
* Add support for the Zfa extension
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmSr+ekACgkQr3yVEwxT
# gBMMGg//ZCcyH3KXB49c2KUIFO6FKYUxN9uC3giZCtuGyEH8T2yDgZVVXnxwU+Ij
# +3Ej6T/ZdWMpePC9qf+xKzHWZk7Qc8Tcg+JgQbga573894yZInRwYl8HsSlEKA+Z
# vlqSBPxTlp9rlDwGP/LjGljyIFqL4konk9zi3FL4ZXTF1iHUGrh/953Y3wIreEfl
# KX5UznnWcgy2BqQT1vihMbM8qCVK6iryH+QZ6LiAsPMSX1rIzk8ectQryILzoIYh
# bMiwCLVMyr4ZrUXjmGTF+7/WcOWwhhyfpdstf2iotKALelZtVHit0wHcty2GYQde
# nvN83jJWu04DGXkPBUsqCUQXczGo1QHjJUH3RIRJzfOby/lGt4pSzHAfKA+iNUht
# ikM3SdBsXMO+ogjTtTcCMb7/m2vsMoQP60VRts9Mh3YVD0cgr7RqpqRoEMugVYnr
# ca8Vijf71mB+y+pq477eV1Q8BoKpr8xa1OlFkNKPC17uMD7HoDMI44QgFOgtYp10
# TMsqqyB75q6PZhSEwm63xbmH0Zpo8kSqT/E3MTtGTyPeuL8TNNNSkCmFaGYmRrbI
# XEp7vG2RaDJOvDomS3nUhA5ruc8SaXd0q25q2gLYQfCsehfFqZAwuNB5xf1zS0M0
# ov1/gwaqU93t6nLbo2cCbb0plkIFKwwJ9KKjD06wJ4KPe0TGFzk=
# =3XFD
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 10 Jul 2023 01:30:33 PM BST
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20230710-1' of https://github.com/alistair23/qemu: (54 commits)
riscv: Add support for the Zfa extension
target/riscv/kvm.c: read/write (cbom|cboz)_blocksize in KVM
target/riscv/kvm.c: add kvmconfig_get_cfg_addr() helper
target/riscv: update multi-letter extension KVM properties
target/riscv/cpu.c: create KVM mock properties
target/riscv/cpu.c: remove priv_ver check from riscv_isa_string_ext()
target/riscv/cpu.c: add satp_mode properties earlier
target/riscv/kvm.c: add multi-letter extension KVM properties
target/riscv/kvm.c: update KVM MISA bits
target/riscv: add KVM specific MISA properties
target/riscv/cpu: add misa_ext_info_arr[]
target/riscv/kvm.c: init 'misa_ext_mask' with scratch CPU
target/riscv: handle mvendorid/marchid/mimpid for KVM CPUs
target/riscv: read marchid/mimpid in kvm_riscv_init_machine_ids()
target/riscv: use KVM scratch CPUs to init KVM properties
target/riscv/cpu.c: restrict 'marchid' value
target/riscv/cpu.c: restrict 'mimpid' value
target/riscv/cpu.c: restrict 'mvendorid' value
hw/riscv/virt.c: skip 'mmu-type' FDT if satp mode not set
target/riscv: skip features setup for KVM CPUs
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There is also pci_create_simple() which creates non-multifunction PCI
devices. Accordingly the parameter is always set to true when a multi
function PCI device is to be created.
The reason for the parameter's existence seems to be that it is used in the
internal PCI code as well which is the only location where it gets set to
false. This one usage can be replaced by trivial code.
Remove this redundant, error-prone parameter.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230304114043.121024-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
i440fx_init() is a legacy init function. The previous patches worked towards
TYPE_I440FX_PCI_HOST_BRIDGE to be instantiated the QOM way. Do this now by
transforming the parameters passed to i440fx_init() into property assignments.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-17-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
I440FX needs a different PCI device model if the "igd-passthru" property is
enabled. The type name is currently passed as a parameter to i440fx_init(). This
parameter will be replaced by a property assignment once i440fx_init() gets
resolved.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-16-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce the properties in anticipation of QOM'ification; Q35 has the same
properties.
Note that we want to avoid a "ram size" property in the QOM interface since it
seems redundant to both properties introduced in this change. Thus the removal
of the ram_size parameter. We assume the invariant of both properties to sum up
to "ram size" which is already asserted in pc_memory_init(). Under Xen the
invariant seems to hold as well, so we now also check it there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-15-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The goal is to eliminate i440fx_init() which is a legacy init function. This
neccessitates the memory regions to be properties, like in Q35, which will be
assigned in board code.
Since i440fx needs different PCI devices in Xen mode, and since i440fx shall
be self-contained, the PCI device will be created during realization of the
host. Thus the pointers need to be moved to the host structure to be usable as
properties.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-13-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a macro to avoid copy and pasting strings which can easily
cause typos.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230630073720.21297-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The number of cores/threads per socket are needed for smbios, and are
also useful for other modules.
Provide the helpers to wrap the calculation of cores/threads per socket
so that we can avoid calculation errors caused by other modules miss
topology changes.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20230628135437.1145805-2-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This creates the QEMU side of the vhost-user-scmi device which connects to
the remote daemon. It is based on code of similar vhost-user devices.
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Message-Id: <20230628100524.342666-2-mzamazal@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This functionality can be shared with upcoming use in vhost-user-gpu, so
move it to the shared file to avoid duplicating it.
Signed-off-by: Erico Nunes <ernunes@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230626164708.1163239-2-ernunes@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The guest can disable or never enable Device-TLB. In these cases,
it can't be used even if enabled in QEMU. So, check Device-TLB state
before registering IOMMU notifier and select unmap flag depending on
that. Also, implement a way to change IOMMU notifier flag if Device-TLB
state is changed.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2001312
Signed-off-by: Viktor Prutyanov <viktor@daynix.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230626091258.24453-2-viktor@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Protected Virtualization (PV) is not a real hardware device:
it is a feature of the firmware on s390x that is exposed to
userspace via the KVM interface.
Move the pv.c/pv.h files to target/s390x/kvm/ to make this clearer.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230624200644.23931-1-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Create the AON device when we realize the sifive_e machine.
This patch only implemented the functionality of the watchdog timer,
not all the functionality of the AON device.
Signed-off-by: Tommy Wu <tommy.wu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230627141216.3962299-3-tommy.wu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The watchdog timer is in the always-on domain device of HiFive 1 rev b,
so this patch added the AON device to the sifive_e machine. This patch
only implemented the functionality of the watchdog timer.
Signed-off-by: Tommy Wu <tommy.wu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230627141216.3962299-2-tommy.wu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Report the PCIe capability version for a device
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Robin Voetter <robin@streamhpc.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Make vfio_migration_realize() adhere to the convention of other realize()
callbacks(like qdev_realize) by returning bool instead of int.
Suggested-by: Cédric Le Goater <clg@redhat.com>
Suggested-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Contrary to multiple device blocker which needs to consider already-attached
devices to unblock/block dynamically, the vIOMMU migration blocker is a device
specific config. Meaning it only needs to know whether the device is bypassing
or not the vIOMMU (via machine property, or per pxb-pcie::bypass_iommu), and
does not need the state of currently present devices. For this reason, the
vIOMMU global migration blocker can be consolidated into the per-device
migration blocker, allowing us to remove some unnecessary code.
This change also makes vfio_mig_active() more accurate as it doesn't check for
global blocker.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The Quad Management Engine (QME) manages power related settings for its
quad. The xscom region is separate from the quad xscoms, therefore a new
region is added. The xscoms in a QME select a given core by selecting
the forth nibble.
Implement dummy reads for the stop state history (SSH) and special
wakeup (SPWU) registers. This quietens some sxcom errors when skiboot
boots on p10.
Power9 does not have a QME.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-ID: <20230707071213.9924-1-joel@jms.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The P10 core xscom memory regions overlap because the size is wrong.
The P10 core+L2 xscom region size is allocated as 0x1000 (with some
unused ranges). "EC" is used as a closer match, as "EX" includes L3
which has a disjoint xscom range that would require a different
region if it were implemented.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230706053923.115003-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Rename TYPE_PPC440_PCIX_HOST_BRIDGE to better match its string value,
move it to common header and use it also in sam460ex to replace hard
coded type name.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <1a1c3fe4b120f345d1005ad7ceca4500783691f7.1688641673.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add a QOM type name define for ppc4xx-host-bridge in the common header
and replace direct use of the string name with the constant.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <f6e2956b3a09ee481b970ef7873b374c846ba0a8.1688641673.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Rename the TYPE_PPC4xx_PCI_HOST_BRIDGE define and its string value to
match each other and other similar types and to avoid confusion with
"ppc4xx-host-bridge" type defined in same file.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-ID: <c59c28ef440633dbd1de0bda0a93b7862ef91104.1688641673.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
After previous changes we can now remove the legacy init function and
move the device creation to board code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <29aafeea9f1c871c739600a7b093c5456e8a1dc8.1688586835.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add a PnvQuad class for the P10 powernv machine. No xscoms are
implemented yet, but this allows them to be added.
The size is reduced to avoid the quad region from overlapping with the
core region.
address-space: xscom-0
0000000000000000-00000003ffffffff (prio 0, i/o): xscom-0
0000000100000000-00000001000fffff (prio 0, i/o): xscom-quad.0
0000000100108000-0000000100907fff (prio 0, i/o): xscom-core.3
0000000100110000-000000010090ffff (prio 0, i/o): xscom-core.2
0000000100120000-000000010091ffff (prio 0, i/o): xscom-core.1
0000000100140000-000000010093ffff (prio 0, i/o): xscom-core.0
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-ID: <20230704054204.168547-4-joel@jms.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Make the existing pnv_quad_xscom_read/write be P9 specific, in
preparation for a different P10 callback.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-ID: <20230704054204.168547-3-joel@jms.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The PQ state of a xive interrupt is always initialized to Q=1, which
means the interrupt is disabled. Since a xive source can be embedded
in many objects, this patch adds a property to allow that behavior to
be refined if needed.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230703081215.55252-2-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Fix up the kerneldoc markup and start documenting the various fields
in QDEV related structures. This involved:
- moving overall description to a DOC: comment at top
- fixing various markup issues for types and structures
- adding missing Return: statements
- adding some typedefs to hide QLIST macros in headers
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230630180423.558337-25-alex.bennee@linaro.org>
The lack of SVE memory instrumentation has been an omission in plugin
handling since it was introduced. Fortunately we can utilise the
probe_* functions to force all all memory access to follow the slow
path. We do this by checking the access type and presence of plugin
memory callbacks and if set return the TLB_MMIO flag.
We have to jump through a few hoops in user mode to re-use the flag
but it was the desired effect:
./qemu-system-aarch64 -display none -serial mon:stdio \
-M virt -cpu max -semihosting-config enable=on \
-kernel ./tests/tcg/aarch64-softmmu/memory-sve \
-plugin ./contrib/plugins/libexeclog.so,ifilter=st1w,afilter=0x40001808 -d plugin
gives (disas doesn't currently understand st1w):
0, 0x40001808, 0xe54342a0, ".byte 0xa0, 0x42, 0x43, 0xe5", store, 0x40213010, RAM, store, 0x40213014, RAM, store, 0x40213018, RAM
And for user-mode:
./qemu-aarch64 \
-plugin contrib/plugins/libexeclog.so,afilter=0x4007c0 \
-d plugin \
./tests/tcg/aarch64-linux-user/sha512-sve
gives:
1..10
ok 1 - do_test(&tests[i])
0, 0x4007c0, 0xa4004b80, ".byte 0x80, 0x4b, 0x00, 0xa4", load, 0x5500800370, load, 0x5500800371, load, 0x5500800372, load, 0x5500800373, load, 0x5500800374, load, 0x5500800375, load, 0x5500800376, load, 0x5500800377, load, 0x5500800378, load, 0x5500800379, load, 0x550080037a, load, 0x550080037b, load, 0x550080037c, load, 0x550080037d, load, 0x550080037e, load, 0x550080037f, load, 0x5500800380, load, 0x5500800381, load, 0x5500800382, load, 0x5500800383, load, 0x5500800384, load, 0x5500800385, load, 0x5500800386, lo
ad, 0x5500800387, load, 0x5500800388, load, 0x5500800389, load, 0x550080038a, load, 0x550080038b, load, 0x550080038c, load, 0x550080038d, load, 0x550080038e, load, 0x550080038f, load, 0x5500800390, load, 0x5500800391, load, 0x5500800392, load, 0x5500800393, load, 0x5500800394, load, 0x5500800395, load, 0x5500800396, load, 0x5500800397, load, 0x5500800398, load, 0x5500800399, load, 0x550080039a, load, 0x550080039b, load, 0x550080039c, load, 0x550080039d, load, 0x550080039e, load, 0x550080039f, load, 0x55008003a0, load, 0x55008003a1, load, 0x55008003a2, load, 0x55008003a3, load, 0x55008003a4, load, 0x55008003a5, load, 0x55008003a6, load, 0x55008003a7, load, 0x55008003a8, load, 0x55008003a9, load, 0x55008003aa, load, 0x55008003ab, load, 0x55008003ac, load, 0x55008003ad, load, 0x55008003ae, load, 0x55008003af
(4007c0 is the ld1b in the sha512-sve)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Robert Henry <robhenry@microsoft.com>
Cc: Aaron Lindsay <aaron@os.amperecomputing.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230630180423.558337-20-alex.bennee@linaro.org>
The major parts of VFIO migration are supported today in QEMU. This
includes basic VFIO migration, device dirty page tracking and precopy
support.
Thus, at this point in time, it seems appropriate to make VFIO migration
non-experimental: remove the x prefix from enable_migration property,
change it to ON_OFF_AUTO and let the default value be AUTO.
In addition, make the following adjustments:
1. When enable_migration is ON and migration is not supported, fail VFIO
device realization.
2. When enable_migration is AUTO (i.e., not explicitly enabled), require
device dirty tracking support. This is because device dirty tracking
is currently the only method to do dirty page tracking, which is
essential for migrating in a reasonable downtime. Setting
enable_migration to ON will not require device dirty tracking.
3. Make migration error and blocker messages more elaborate.
4. Remove error prints in vfio_migration_query_flags().
5. Rename trace_vfio_migration_probe() to
trace_vfio_migration_realize().
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Currently, VFIO bytes_transferred is not reset properly:
1. bytes_transferred is not reset after a VM snapshot (so a migration
following a snapshot will report incorrect value).
2. bytes_transferred is a single counter for all VFIO devices, however
upon migration failure it is reset multiple times, by each VFIO
device.
Fix it by introducing a new function vfio_reset_bytes_transferred() and
calling it during migration and snapshot start.
Remove existing bytes_transferred reset in VFIO migration state
notifier, which is not needed anymore.
Fixes: 3710586caa ("qapi: Add VFIO devices migration stats in Migration stats")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
A common helper implementing the realloc algorithm for handling
capabilities.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Robin Voetter <robin@streamhpc.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Loading of a VFIO device's data can take a substantial amount of time as
the device may need to allocate resources, prepare internal data
structures, etc. This can increase migration downtime, especially for
VFIO devices with a lot of resources.
To solve this, VFIO migration uAPI defines "initial bytes" as part of
its precopy data stream. Initial bytes can be used in various ways to
improve VFIO migration performance. For example, it can be used to
transfer device metadata to pre-allocate resources in the destination.
However, for this to work we need to make sure that all initial bytes
are sent and loaded in the destination before the source VM is stopped.
Use migration switchover ack capability to make sure a VFIO device's
initial bytes are sent and loaded in the destination before the source
stops the VM and attempts to complete the migration.
This can significantly reduce migration downtime for some devices.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Pre-copy support allows the VFIO device data to be transferred while the
VM is running. This helps to accommodate VFIO devices that have a large
amount of data that needs to be transferred, and it can reduce migration
downtime.
Pre-copy support is optional in VFIO migration protocol v2.
Implement pre-copy of VFIO migration protocol v2 and use it for devices
that support it. Full description of it can be found in the following
Linux commit: 4db52602a607 ("vfio: Extend the device migration protocol
with PRE_COPY").
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
VFIO migration flags are queried once in vfio_migration_init(). Store
them in VFIOMigration so they can be used later to check the device's
migration capabilities without re-querying them.
This will be used in the next patch to check if the device supports
precopy migration.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: YangHang Liu <yanghliu@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
"kvm_arm.h" contains external and internal prototype declarations.
Files under the hw/ directory should only access the KVM external
API.
In order to avoid machine / device models to include "kvm_arm.h"
simply to get the QOM GIC/ITS class name, un-inline each class
name getter to the proper device model file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230405160454.97436-4-philmd@linaro.org>
We want all accelerators to share the same opaque pointer in
CPUState.
Rename the 'hvf_vcpu_state' structure as 'AccelCPUState'.
Use the generic 'accel' field of CPUState instead of 'hvf'.
Replace g_malloc0() by g_new0() for readability.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230624174121.11508-17-philmd@linaro.org>
hThread variable is only used by the HAX accelerator,
so move it to the accelerator specific context.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230624174121.11508-9-philmd@linaro.org>
We want all accelerators to share the same opaque pointer in
CPUState. Start with the HAX context, renaming its forward
declarated structure 'hax_vcpu_state' as 'AccelCPUState'.
Document the CPUState field. Directly use the typedef.
Remove the amusing but now unnecessary casts in NVMM / WHPX.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230624174121.11508-8-philmd@linaro.org>
All accelerators will share a single opaque context
in CPUState. Start by renaming 'hax_vcpu' as 'accel'.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230624174121.11508-7-philmd@linaro.org>
SUN Type 4, 5 and 5c keyboards have dip switches to choose the language layout
of the keyboard. Solaris makes an ioctl to query the value of the dipswitches
and uses that value to select keyboard layout. Also the SUN bios like the one
in the file ss5.bin uses this value to support at least some keyboard layouts.
However, the OpenBIOS provided with qemu is hardcoded to always use an US
keyboard layout.
Before this patch, qemu allways gave dip switch value 0x21 (US keyboard),
this patch uses a command line switch like
"-global escc.chnA-sunkbd-layout=de" to select dip switch value. A table is
used to lookup values from arguments like:
-global escc.chnA-sunkbd-layout=fr
-global escc.chnA-sunkbd-layout=es
But the patch also accepts numeric dip switch values directly:
-global escc.chnA-sunkbd-layout=0x2b
-global escc.chnA-sunkbd-layout=43
Both values above are the same and select swedish keyboard as explained in
table 3-15 at
https://docs.oracle.com/cd/E19683-01/806-6642/new-43/index.html
Unless you want to do a full Solaris installation but happen to have
access to a Sun bios file, the easiest way to test that the patch works
is to:
qemu-system-sparc -global escc.chnA-sunkbd-layout=sv -bios /path/to/ss5.bin
If you already happen to have a Solaris installation in a qemu disk image
file you can easily try different keyboard layouts after this patch is
applied.
Signed-off-by: Henrik Carlqvist <hc1245@poolhem.se>
Message-Id: <20230623203007.56d3d182.hc981@poolhem.se>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[MCA edit: update unsigned char to uint8_t, fix spacing issues]
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Allocate pixman bits for scanouts with qemu_win32_map_alloc() so we can
set a shareable handle on the associated display surface.
Note: when bits are provided to pixman_image_create_bits(), you must also give
the rowstride (the argument is ignored when bits is NULL)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230606115658.677673-11-marcandre.lureau@redhat.com>
We have run out of bits we can use within the CPUTLBEntry comparators,
as TLB_FLAGS_MASK cannot overlap alignment.
Store slow_flags[] in CPUTLBEntryFull, and merge with the flags from
the comparator. A new TLB_FORCE_SLOW bit is set within the comparator
as an indication that the slow path must be used.
Move TLB_BSWAP to TLB_SLOW_FLAGS_MASK. Since we are out of bits,
we cannot create a new bit without moving an old one.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
asymmetric crypto support for cryptodev-vhost-user
rom migration when rom size changes
poison get, inject, clear; mock cxl events and irq support for cxl
shadow virtqueue offload support for vhost-vdpa
vdpa now maps shadow vrings with MAP_SHARED
max_cpus went up to 1024 and we default to smbios 3.0 for pc
Fixes, cleanups all over the place. In particular
hw/acpi: Fix PM control register access
works around a very long standing bug in memory core.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmSZl5EPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRph+8H/RZodqCadmQ1evpeWs7RBSvJeZgbJTVl/9/h
+ObvEmVz2+X4D+O1Kxh54vDV0SNVq3XjyrFy3Ur57MAR6r2ZWwB6HySaeFdi4zIm
N0SMkfUylDnf7ulyjzJoXDzHOoFnqAM6fU/jcoQXBIdUeeqwPrzLOZHrGrwevPWK
iH5JP66suOVlBuKLJjlUKI3/4vK3oTod5Xa3Oz2Cw1oODtbIa97N8ZAdBgZd3ah9
7mjZjcH54kFRwfidz/rkpY5NMru8BlD54MyEOWofvTL2w7aoWmVO99qHEK+SjLkG
x4Mx3aYlnOEvkJ+5yBHvtXS4Gc5T9ltY84AvcwPNuz4RKCORi1s=
=Do8p
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: fixes, features, cleanups
asymmetric crypto support for cryptodev-vhost-user
rom migration when rom size changes
poison get, inject, clear; mock cxl events and irq support for cxl
shadow virtqueue offload support for vhost-vdpa
vdpa now maps shadow vrings with MAP_SHARED
max_cpus went up to 1024 and we default to smbios 3.0 for pc
Fixes, cleanups all over the place. In particular
hw/acpi: Fix PM control register access
works around a very long standing bug in memory core.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmSZl5EPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRph+8H/RZodqCadmQ1evpeWs7RBSvJeZgbJTVl/9/h
# +ObvEmVz2+X4D+O1Kxh54vDV0SNVq3XjyrFy3Ur57MAR6r2ZWwB6HySaeFdi4zIm
# N0SMkfUylDnf7ulyjzJoXDzHOoFnqAM6fU/jcoQXBIdUeeqwPrzLOZHrGrwevPWK
# iH5JP66suOVlBuKLJjlUKI3/4vK3oTod5Xa3Oz2Cw1oODtbIa97N8ZAdBgZd3ah9
# 7mjZjcH54kFRwfidz/rkpY5NMru8BlD54MyEOWofvTL2w7aoWmVO99qHEK+SjLkG
# x4Mx3aYlnOEvkJ+5yBHvtXS4Gc5T9ltY84AvcwPNuz4RKCORi1s=
# =Do8p
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 26 Jun 2023 03:50:09 PM CEST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (53 commits)
vhost-vdpa: do not cleanup the vdpa/vhost-net structures if peer nic is present
vhost_net: add an assertion for TAP client backends
intel_iommu: Fix address space unmap
intel_iommu: Fix flag check in replay
intel_iommu: Fix a potential issue in VFIO dirty page sync
vhost-user: fully use new backend/frontend naming
virtio-scsi: avoid dangling host notifier in ->ioeventfd_stop()
hw/i386/pc: Clean up pc_machine_initfn
vdpa: fix not using CVQ buffer in case of error
vdpa: mask _F_CTRL_GUEST_OFFLOADS for vhost vdpa devices
vhost: fix vhost_dev_enable_notifiers() error case
vdpa: Allow VIRTIO_NET_F_CTRL_GUEST_OFFLOADS in SVQ
vdpa: Add vhost_vdpa_net_load_offloads()
virtio-net: expose virtio_net_supported_guest_offloads()
hw/net/virtio-net: make some VirtIONet const
vdpa: reuse virtio_vdev_has_feature()
include/hw/virtio: make some VirtIODevice const
vdpa: map shadow vrings with MAP_SHARED
vdpa: reorder vhost_vdpa_net_cvq_cmd_page_len function
vdpa: do not block migration if device has cvq and x-svq=on
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Slave/master nomenclature was replaced with backend/frontend in commit
1fc19b6527 ("vhost-user: Adopt new backend naming")
This patch replaces all remaining uses of master and slave in the
codebase.
Signed-off-by: Emmanouil Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20230613080849.2115347-1-manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
To support restoring offloads state in vdpa, it is necessary to
expose the function virtio_net_supported_guest_offloads().
According to VirtIO standard, "Upon feature negotiation
corresponding offload gets enabled to preserve backward compatibility.".
Therefore, QEMU uses this function to get the device supported offloads.
This allows QEMU to know the device's defaults and skip the control
message sending if these defaults align with the driver's configuration.
Note that the device's defaults can mismatch the driver's configuration
only at live migration.
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <43679506f3f039a7aa2bdd5b49785107b5dfd7d4.1685704856.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Tested-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The VirtIODevice structure is not modified in
virtio_vdev_has_feature(). Therefore, make it const
to allow this function to accept const variables.
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Reviewed-by: Eugenio Pérez Martin <eperezma@redhat.com>
Message-Id: <16c0561b921310a32c240a4fb6e8cee3ffee16fe.1685704856.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Tested-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, pc-q35 and pc-i44fx machine models are default to use SMBIOS 2.8
(32-bit entry point). Since SMBIOS 3.0 (64-bit entry point) is now fully
supported since QEMU 7.0, default to use SMBIOS 3.0 for newer machine
models. This is necessary to avoid the following message when launching
a VM with large number of vcpus.
"SMBIOS 2.1 table length 66822 exceeds 65535"
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Message-Id: <20230607205717.737749-2-suravee.suthikulpanit@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
* Validate cluster and NUMA node boundary on ARM and RISC-V
* various small TCG features from newer processors
* Remove dubious 'event_notifier-posix.c' include
* fix git-submodule.sh in releases
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmSZS0IUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroN+tgf/axJdG9NXKCyXgc0vzjKVhSR4Y+tC
EPxkg7Rq7uOMgbph9oTS/2Kzh9LnP6kLt2qnS4igRHGuEBd58yD6fFNDv0LJsK/l
B/d0WGHMKV0KMYOX24rkyfohVu37GhVRsiVSIlIiQVTC9JtYer7WxdnyoDaPKvY8
dpbKgDrd59vAlsHrpj7ZubVQPcL3lXrLryimpDohMH6Ba+4wZq+7dKPpal97QOP2
3i7isUBTQiMOcVjW6GEiNcDLSJqj5DSgylhdFnaBsq/ThpC2PxWoXcCbV28QELzf
5+J+RXQavmeWKZMR0q98iBzWbrsVtaSxAkHHiwbUMMqQvkfY6Dpo5dMHWw==
=WHE2
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* kvm: reuse per-vcpu stats fd to avoid vcpu interruption
* Validate cluster and NUMA node boundary on ARM and RISC-V
* various small TCG features from newer processors
* Remove dubious 'event_notifier-posix.c' include
* fix git-submodule.sh in releases
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmSZS0IUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroN+tgf/axJdG9NXKCyXgc0vzjKVhSR4Y+tC
# EPxkg7Rq7uOMgbph9oTS/2Kzh9LnP6kLt2qnS4igRHGuEBd58yD6fFNDv0LJsK/l
# B/d0WGHMKV0KMYOX24rkyfohVu37GhVRsiVSIlIiQVTC9JtYer7WxdnyoDaPKvY8
# dpbKgDrd59vAlsHrpj7ZubVQPcL3lXrLryimpDohMH6Ba+4wZq+7dKPpal97QOP2
# 3i7isUBTQiMOcVjW6GEiNcDLSJqj5DSgylhdFnaBsq/ThpC2PxWoXcCbV28QELzf
# 5+J+RXQavmeWKZMR0q98iBzWbrsVtaSxAkHHiwbUMMqQvkfY6Dpo5dMHWw==
# =WHE2
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 26 Jun 2023 10:24:34 AM CEST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [undefined]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
git-submodule.sh: allow running in validate mode without previous update
target/i386: implement SYSCALL/SYSRET in 32-bit emulators
target/i386: implement RDPID in TCG
target/i386: sysret and sysexit are privileged
target/i386: AMD only supports SYSENTER/SYSEXIT in 32-bit mode
target/i386: Intel only supports SYSCALL/SYSRET in long mode
target/i386: TCG supports WBNOINVD
target/i386: TCG supports XSAVEERPTR
target/i386: do not accept RDSEED if CPUID bit absent
target/i386: TCG supports RDSEED
target/i386: TCG supports 3DNow! prefetch(w)
target/i386: fix INVD vmexit
kvm: reuse per-vcpu stats fd to avoid vcpu interruption
hw/riscv: Validate cluster and NUMA node boundary
hw/arm: Validate cluster and NUMA node boundary
numa: Validate cluster and NUMA node boundary if required
hw/remote/proxy: Remove dubious 'event_notifier-posix.c' include
build: further refine build.ninja rules
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A regression has been detected in latency testing of KVM guests.
More specifically, it was observed that the cyclictest
numbers inside of an isolated vcpu (running on isolated pcpu) are:
Where a maximum of 50us is acceptable.
The implementation of KVM_GET_STATS_FD uses run_on_cpu to query
per vcpu statistics, which interrupts the vcpu (and is unnecessary).
To fix this, open the per vcpu stats fd on vcpu initialization,
and read from that fd from QEMU's main thread.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For some architectures like ARM64, multiple CPUs in one cluster can be
associated with different NUMA nodes, which is irregular configuration
because we shouldn't have this in baremetal environment. The irregular
configuration causes Linux guest to misbehave, as the following warning
messages indicate.
-smp 6,maxcpus=6,sockets=2,clusters=1,cores=3,threads=1 \
-numa node,nodeid=0,cpus=0-1,memdev=ram0 \
-numa node,nodeid=1,cpus=2-3,memdev=ram1 \
-numa node,nodeid=2,cpus=4-5,memdev=ram2 \
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/sched/topology.c:2271 build_sched_domains+0x284/0x910
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.14.0-268.el9.aarch64 #1
pstate: 00400005 (nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : build_sched_domains+0x284/0x910
lr : build_sched_domains+0x184/0x910
sp : ffff80000804bd50
x29: ffff80000804bd50 x28: 0000000000000002 x27: 0000000000000000
x26: ffff800009cf9a80 x25: 0000000000000000 x24: ffff800009cbf840
x23: ffff000080325000 x22: ffff0000005df800 x21: ffff80000a4ce508
x20: 0000000000000000 x19: ffff000080324440 x18: 0000000000000014
x17: 00000000388925c0 x16: 000000005386a066 x15: 000000009c10cc2e
x14: 00000000000001c0 x13: 0000000000000001 x12: ffff00007fffb1a0
x11: ffff00007fffb180 x10: ffff80000a4ce508 x9 : 0000000000000041
x8 : ffff80000a4ce500 x7 : ffff80000a4cf920 x6 : 0000000000000001
x5 : 0000000000000001 x4 : 0000000000000007 x3 : 0000000000000002
x2 : 0000000000001000 x1 : ffff80000a4cf928 x0 : 0000000000000001
Call trace:
build_sched_domains+0x284/0x910
sched_init_domains+0xac/0xe0
sched_init_smp+0x48/0xc8
kernel_init_freeable+0x140/0x1ac
kernel_init+0x28/0x140
ret_from_fork+0x10/0x20
Improve the situation to warn when multiple CPUs in one cluster have
been associated with different NUMA nodes. However, one NUMA node is
allowed to be associated with different clusters.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230509002739.18388-2-gshan@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The presenters for xive on P9 and P10 are mostly similar but the
behavior can be tuned through a few CQ registers. This patch adds a
"get_config" method, which will allow to access that config from the
presenter in a later patch.
For now, just define the config for the TIMA version.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Doorbells in SMT need to coordinate msgsnd/msgclr and DPDES access from
multiple threads that affect the same state.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Create spapr_nested.c for most of the nested HV implementation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rather than use a copy of CPUPPCState to store the host state while
the environment has been switched to the L2, use a new struct for
this purpose.
Have helper functions to save and load this host state.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These events include a copy of the device health information at the
time of the event. Actually using the emulated device health would
require a lot of controls to manipulate that state. Given the aim
of this injection code is to just test the flows when events occur,
inject the contents of the device health state as well.
Future work may add more sophisticate device health emulation
including direct generation of these records when events occur
(such as a temperature threshold being crossed). That does not
reduce the usefulness of this more basic generation of the events.
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230530133603.16934-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Defined in CXL r3.0 8.2.9.2.1.2 DRAM Event Record, this event
provides information related to DRAM devices.
Example injection command in QMP:
{ "execute": "cxl-inject-dram-event",
"arguments": {
"path": "/machine/peripheral/cxl-mem0",
"log": "informational",
"flags": 1,
"dpa": 1000,
"descriptor": 3,
"type": 3,
"transaction-type": 192,
"channel": 3,
"rank": 17,
"nibble-mask": 37421234,
"bank-group": 7,
"bank": 11,
"row": 2,
"column": 77,
"correction-mask": [33, 44, 55,66]
}}
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230530133603.16934-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To facilitate testing provide a QMP command to inject a general media
event. The event can be added to the log specified.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230530133603.16934-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Replace the stubbed out CXL Get/Set Event interrupt policy mailbox
commands. Enable those commands to control interrupts for each of the
event log types.
Skip the standard input mailbox length on the Set command due to DCD
being optional. Perform the checks separately.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230530133603.16934-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL testing is benefited from an artificial event log injection
mechanism.
Add an event log infrastructure to insert, get, and clear events from
the various logs available on a device.
Replace the stubbed out CXL Get/Clear Event mailbox commands with
commands that operate on the new infrastructure.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230530133603.16934-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Following patches will need access to the mailbox return code
type so move it to the header.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230530133603.16934-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The device status register block was defined. However, there were no
individual registers nor any data wired up.
Define the event status register [CXL 3.0; 8.2.8.3.1] as part of the
device status register block. Wire up the register and initialize the
event status for each log.
To support CXL 3.0 the version of the device status register block needs
to be 2. Change the macro to allow for setting the version.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230530133603.16934-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current implementation is very simple so many of the corner
cases do not exist (e.g. fragmenting larger poison list entries)
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230526170010.574-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Inject poison using QMP command cxl-inject-poison to add an entry to the
poison list.
For now, the poison is not returned CXL.mem reads, but only via the
mailbox command Get Poison List. So a normal memory read to an address
that is on the poison list will not yet result in a synchronous exception
(and similar for partial cacheline writes).
That is left for a future patch.
See CXL rev 3.0, sec 8.2.9.8.4.1 Get Poison list (Opcode 4300h)
Kernel patches to use this interface here:
https://lore.kernel.org/linux-cxl/cover.1665606782.git.alison.schofield@intel.com/
To inject poison using QMP (telnet to the QMP port)
{ "execute": "qmp_capabilities" }
{ "execute": "cxl-inject-poison",
"arguments": {
"path": "/machine/peripheral/cxl-pmem0",
"start": 2048,
"length": 256
}
}
Adjusted to select a device on your machine.
Note that the poison list supported is kept short enough to avoid the
complexity of state machine that is needed to handle the MORE flag.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230526170010.574-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Also change the instantiation of the macfb device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-23-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the mac-nubus-bridge device to use
object_initialize_child() and map the Nubus address space using
memory_region_add_subregion() instead of sysbus_mmio_map().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the SWIM device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the ESP device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the escc_orgate device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the ESCC device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the dp8393x device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Jason Wang <jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This is to enable them to be used outside of dp8393x.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Jason Wang <jasowang@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the VIA2 device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the VIA1 device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The current use of aliased memory regions causes us 2 problems: firstly the
output of "info qom-tree" is absolutely huge and difficult to read, and
secondly we have already reached the internal limit for memory regions as
adding any new memory region into the mac-io region causes QEMU to assert
with "phys_section_add: Assertion `map->sections_nb < TARGET_PAGE_SIZE'
failed".
Implement the mac-io region aliasing using a single IO memory region that
applies IO_SLICE_MASK representing the maximum size of the aliased region and
then forwarding the access to the existing mac-io memory region using the
address space API.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move all devices from the IO region to within the container in preparation
for updating the IO aliasing mechanism.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the GLUE device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will allow the q800-glue.h header to be included separately so that the
GLUE device can be referenced externally.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-8-mark.cave-ayland@ilande.co.uk>
[lv: update comment]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the CPU to use object_initialize_child()
followed by a separate realisation.
Restrict valid CPU types to m68040.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-6-mark.cave-ayland@ilande.co.uk>
[lv: update commit message]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This provides an overall container and owner for Machine-related objects such
as MemoryRegions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This reverts commit d7ee93e243.
That commit tries to make a field in the CPUState struct not be
present when CONFIG_USER_ONLY is set. Unfortunately, you can't
conditionally omit fields in structs like this based on ifdefs that
are set per-target. If you try it, then code in files compiled
per-target (where CONFIG_USER_ONLY is or can be set) will disagree
about the struct layout with files that are compiled once-only (where
this kind of ifdef is never set).
This manifests specifically in 'make check-tcg' failing, because code
in cpus-common.c that sets up the CPUState::cpu_index field puts it
at a different offset from the code in plugins/core.c in
qemu_plugin_vcpu_init_hook() which reads the cpu_index field. The
latter then hits an assert because from its point of view every
thread has a 0 cpu_index. There might be other weird behaviour too.
Mostly we catch this kind of bug because the CONFIG_whatever is
listed in include/exec/poison.h and so the reference to it in
build-once source files will then cause a compiler error.
Unfortunately CONFIG_USER_ONLY is an exception to that: we have some
places where we use it in "safe" ways in headers that will be seen by
once-only source files (e.g. ifdeffing out function prototypes) and
it would be a lot of refactoring to be able to get to a position
where we could poison it. This leaves us in a "you have to be
careful to walk around the bear trap" situation...
Fixes: d7ee93e243 ("cputlb: Restrict SavedIOTLB to system emulation")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230620175712.1331625-1-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Commit 2f3a57ee47 ("cputlb: ensure we save the IOTLB data in
case of reset") added the SavedIOTLB structure -- which is
system emulation specific -- in the generic CPUState structure.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216215519.5522-3-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since we *might* have user emulation with softmmu,
replace the system emulation check by !user emulation one.
Invert the #ifdef'ry in TCGCPUOps structure for clarity.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-6-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230612223456.33824-5-philmd@linaro.org
Message-Id: <20230531155258.8361-1-sergey.kambalin@auriga.com>
[PMD: Split from bigger patch: 3/4]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[PMM: added a comment about RPI_FIRMWARE_CORE_CLK_RATE
really being SoC-specific]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Linux kernel added a flood check for RX data recently in commit
496a4471b7c3 ("serial: imx: work-around for hardware RX flood"). This
check uses the wake bit in the UART status register 2. The wake bit
indicates that the receiver detected a start bit on the RX line. If the
kernel sees a number of RX interrupts without the wake bit being set, it
treats this as spurious data and resets the UART port. imx_serial does
never set the wake bit and triggers the kernel's flood check.
This patch adds support for the wake bit. wake is set when we receive a
new character (it's not set for break events). It seems that wake is
cleared by the kernel driver, the hardware does not have to clear it
automatically after data was read.
The wake bit can be configured as an interrupt source. Support this
mechanism as well.
Co-developed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a new machine xenpvh which creates a IOREQ server to register/connect with
Xen Hypervisor.
Optional: When CONFIG_TPM is enabled, it also creates a tpm-tis-device, adds a
TPM emulator and connects to swtpm running on host machine via chardev socket
and support TPM functionalities for a guest domain.
Extra command line for aarch64 xenpvh QEMU to connect to swtpm:
-chardev socket,id=chrtpm,path=/tmp/myvtpm2/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-machine tpm-base-addr=0x0c000000 \
swtpm implements a TPM software emulator(TPM 1.2 & TPM 2) built on libtpms and
provides access to TPM functionality over socket, chardev and CUSE interface.
Github repo: https://github.com/stefanberger/swtpm
Example for starting swtpm on host machine:
mkdir /tmp/vtpm2
swtpm socket --tpmstate dir=/tmp/vtpm2 \
--ctrl type=unixio,path=/tmp/vtpm2/swtpm-sock &
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
This is done to prepare for enabling xenpv support for ARM architecture.
On ARM it is possible to have a functioning xenpv machine with only the
PV backends and no IOREQ server. If the IOREQ server creation fails,
continue to the PV backends initialization.
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Paul Durrant <paul@xen.org>
This patch does following:
1. creates arch_handle_ioreq() and arch_xen_set_memory(). This is done in
preparation for moving most of xen-hvm code to an arch-neutral location,
move the x86-specific portion of xen_set_memory to arch_xen_set_memory.
Also, move handle_vmport_ioreq to arch_handle_ioreq.
2. Pure code movement: move common functions to hw/xen/xen-hvm-common.c
Extract common functionalities from hw/i386/xen/xen-hvm.c and move them to
hw/xen/xen-hvm-common.c. These common functions are useful for creating
an IOREQ server.
xen_hvm_init_pc() contains the architecture independent code for creating
and mapping a IOREQ server, connecting memory and IO listeners, initializing
a xen bus and registering backends. Moved this common xen code to a new
function xen_register_ioreq() which can be used by both x86 and ARM machines.
Following functions are moved to hw/xen/xen-hvm-common.c:
xen_vcpu_eport(), xen_vcpu_ioreq(), xen_ram_alloc(), xen_set_memory(),
xen_region_add(), xen_region_del(), xen_io_add(), xen_io_del(),
xen_device_realize(), xen_device_unrealize(),
cpu_get_ioreq_from_shared_memory(), cpu_get_ioreq(), do_inp(),
do_outp(), rw_phys_req_item(), read_phys_req_item(),
write_phys_req_item(), cpu_ioreq_pio(), cpu_ioreq_move(),
cpu_ioreq_config(), handle_ioreq(), handle_buffered_iopage(),
handle_buffered_io(), cpu_handle_ioreq(), xen_main_loop_prepare(),
xen_hvm_change_state_handler(), xen_exit_notifier(),
xen_map_ioreq_server(), destroy_hvm_domain() and
xen_shutdown_fatal_error()
3. Removed static type from below functions:
1. xen_region_add()
2. xen_region_del()
3. xen_io_add()
4. xen_io_del()
5. xen_device_realize()
6. xen_device_unrealize()
7. xen_hvm_change_state_handler()
8. cpu_ioreq_pio()
9. xen_exit_notifier()
4. Replace TARGET_PAGE_SIZE with XC_PAGE_SIZE to match the page side with Xen.
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
* Skip Vector set tail when vta is zero
* Move zc* out of the experimental properties
* Mask the implicitly enabled extensions in isa_string based on priv version
* Rework CPU extension validation and validate MISA changes
* Fixup PMP TLB cacheing errors
* Writing to pmpaddr and MML/MMWP correctly triggers TLB flushes
* Fixup PMP bypass checks
* Deny access if access is partially inside a PMP entry
* Correct OpenTitanState parent type/size
* Fix QEMU crash when NUMA nodes exceed available CPUs
* Fix pointer mask transformation for vector address
* Updates and improvements for Smstateen
* Support disas for Zcm* extensions
* Support disas for Z*inx extensions
* Remove unused decomp_rv32/64 value for vector instructions
* Enable PC-relative translation
* Assume M-mode FW in pflash0 only when "-bios none"
* Support using pflash via -blockdev option
* Add vector registers to log
* Clean up reference of Vector MTYPE
* Remove the check for extra Vector tail elements
* Smepmp: Return error when access permission not allowed in PMP
* Fixes for smsiaddrcfg and smsiaddrcfgh in AIA
-----BEGIN PGP SIGNATURE-----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=fOTc
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230614' of https://github.com/alistair23/qemu into staging
Second RISC-V PR for 8.1
* Skip Vector set tail when vta is zero
* Move zc* out of the experimental properties
* Mask the implicitly enabled extensions in isa_string based on priv version
* Rework CPU extension validation and validate MISA changes
* Fixup PMP TLB cacheing errors
* Writing to pmpaddr and MML/MMWP correctly triggers TLB flushes
* Fixup PMP bypass checks
* Deny access if access is partially inside a PMP entry
* Correct OpenTitanState parent type/size
* Fix QEMU crash when NUMA nodes exceed available CPUs
* Fix pointer mask transformation for vector address
* Updates and improvements for Smstateen
* Support disas for Zcm* extensions
* Support disas for Z*inx extensions
* Remove unused decomp_rv32/64 value for vector instructions
* Enable PC-relative translation
* Assume M-mode FW in pflash0 only when "-bios none"
* Support using pflash via -blockdev option
* Add vector registers to log
* Clean up reference of Vector MTYPE
* Remove the check for extra Vector tail elements
* Smepmp: Return error when access permission not allowed in PMP
* Fixes for smsiaddrcfg and smsiaddrcfgh in AIA
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmSJFRoACgkQr3yVEwxT
# gBMUkg/8Cuhqpx+zy7MeouVkyhEjUuhtCWyr0WVZBJzDkVEOrlY6TyR0hb5/o1Js
# LZf6ZMF6JQDN78bmUct8yFBZBGafey5tyonDCsnD7CNQuLPf2NSjTHhu9n5hKFqF
# F8Mpn9iFu6k1pr0iF7FbCccVWuDb3P4h2PaM0iFhmf4uz42BCMYdgJThhvv38xlt
# jr6A3dcjTpp8yB+iRCuhL2IU2XVee0XBiDUECqRXd0gmtOtqJNST8L+l8YkLy1VO
# WUMe8RCO6NMP7BLJ383WwCDeiFTo0mJebZQ0eR/G1xEhy7c8BBMh/CgQmq2F3wDZ
# Q0biaeozADgAaCC7aOAHI+1sAoMhOm1v2WhIVmh+XXUqT9856cKwc7DUPBmzb9Sj
# N5Zh+t9WCnZG7qpfxvkDF0Y/aRODMHZ1BW5L/ky9yBtyuRwXOJ6VycZTFyRkSwnN
# Gd/s9IClDOP1IP5s4TSMGGdelk4lH97x7fZE/2hxn59lp761JtMxbaEceBtqaBh8
# zNMTNN/KHs8LeiIBI2ZZ+nQav452Y6XYBivQ7OdsI8xkjnjG9gfgXXjvX1TIh0ow
# Hy5ZxtAtjXty49Gmjkx5VcBx4auJcnRDlLTzoZjTxq1te+gEWpw6O1EsEKasVLZe
# uN6PxTOxS3nHvRvPgQc1xNUdhDRqBaYsju6b9YmMxz1uefAjGM0=
# =fOTc
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 14 Jun 2023 03:17:14 AM CEST
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20230614' of https://github.com/alistair23/qemu: (60 commits)
hw/intc: If mmsiaddrcfgh.L == 1, smsiaddrcfg and smsiaddrcfgh are read-only.
target/riscv: Smepmp: Return error when access permission not allowed in PMP
target/riscv/vector_helper.c: Remove the check for extra tail elements
target/riscv/vector_helper.c: clean up reference of MTYPE
target/riscv: Fix initialized value for cur_pmmask
util/log: Add vector registers to log
docs/system: riscv: Add pflash usage details
riscv/virt: Support using pflash via -blockdev option
hw/riscv: virt: Assume M-mode FW in pflash0 only when "-bios none"
target/riscv: Remove pc_succ_insn from DisasContext
target/riscv: Enable PC-relative translation
target/riscv: Use true diff for gen_pc_plus_diff
target/riscv: Change gen_set_pc_imm to gen_update_pc
target/riscv: Change gen_goto_tb to work on displacements
target/riscv: Introduce cur_insn_len into DisasContext
target/riscv: Fix target address to update badaddr
disas/riscv.c: Remove redundant parentheses
disas/riscv.c: Fix lines with over 80 characters
disas/riscv.c: Remove unused decomp_rv32/64 value for vector instructions
disas/riscv.c: Support disas for Z*inx extensions
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allows the struct to be embedded directly into device models without additional
allocation.
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230612081238.1742-3-shentey@gmail.com>
[PMD: Update MAINTAINERS entry and use SPDX license identifier]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Exporting ParallelState is a precondition for exporing TYPE_ISA_PARALLEL to be
performed in the next patch.
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230612081238.1742-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Added QEMU option 'vpu' to log vector extension registers such as gpr\fpu.
Signed-off-by: Ivan Klokov <ivan.klokov@syntacore.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230410124451.15929-2-ivan.klokov@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
OpenTitanState is the 'machine' (or 'board') state: it isn't
a SysBus device, but inherits from the MachineState type.
Correct the instance size.
Doing so we avoid leaking an OpenTitanState pointer in
opentitan_machine_init().
Fixes: fe0fe4735e ("riscv: Initial commit of OpenTitan machine")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230520054510.68822-6-philmd@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Expand the DEFINE_MACHINE() macro, converting the class_init()
handler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230520054510.68822-5-philmd@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
QOM type names are usually defined as TYPE_FOO.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20230520054510.68822-4-philmd@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
While reviewing, the ROUND_UP() macro is easier to figure out.
Besides, the comment confirms we want to round up here.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230523061546.49031-1-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
TIMA addresses are somewhat special and are split in several bit
fields with different meanings. This patch describes it and introduce
macros to more easily access the various fields.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-5-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
During the last patches, TYPE_PIIX3_XEN_DEVICE turned into a clone of
TYPE_PIIX3_DEVICE. Remove this redundancy.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-7-shentey@gmail.com>
Message-Id: <20230403074124.3925-8-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xen_piix3_set_irq() isn't PIIX specific: PIIX is a single PCI device
while xen_piix3_set_irq() maps multiple PCI devices to their respective
IRQs, which is board-specific. Rename xen_piix3_set_irq() to communicate
this.
Also rename XEN_PIIX_NUM_PIRQS to XEN_IOAPIC_NUM_PIRQS since the Xen's
IOAPIC rather than PIIX has this many interrupt routes.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-2-shentey@gmail.com>
Message-Id: <20230403074124.3925-2-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
In restructuring to allow for internal emulation of Xen functionality,
I broke compatibility for Xen 4.6 and earlier. Fix this by explicitly
removing support for anything older than 4.7.1, which is also ancient
but it does still build, and the compatibility support for it is fairly
unintrusive.
Fixes: 15e283c5b6 ("hw/xen: Add foreignmem operations to allow redirection to internal emulation")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230412185102.441523-4-dwmw2@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Only a few important registers are added, especially the SRAM_VER
register.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
R40 has two ethernet controllers named as emac and gmac. The emac is
compatibled with A10, and the GMAC is compatibled with H3.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A64's sd register was similar to H3, and it introduced a new register
named SAMP_DL_REG location at 0x144. The dma descriptor buffer size of
mmc2 is only 8K and the other mmc controllers has 64K.
Also fix allwinner-r40's mmc controller type.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Types of memory that the SDRAM controller supports are DDR2/DDR3
and capacities of up to 2GiB. This commit adds emulation support
of the Allwinner R40 SDRAM controller.
This driver only support 256M, 512M and 1024M memory now.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TWI(i2c) is designed to be used as an interface between CPU host and the
serial 2-Wire bus. It can support all standard 2-Wire transfer, can be
operated in standard mode(100kbit/s) or fast-mode, supporting data rate
up to 400kbit/s.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
R40 has eight UARTs, support both 16450 and 16550 compatible modes.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CCU provides the registers to program the PLLs and the controls
most of the clock generation, division, distribution, synchronization
and gating.
This commit adds support for the Clock Control Unit which emulates
a simple read/write register interface.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 (sun8i) SoC features a Quad-Core Cortex-A7 ARM CPU,
and a Mali400 MP2 GPU from ARM. It's also known as the Allwinner T3
for In-Car Entertainment usage, A40i and A40pro are variants that
differ in applicable temperatures range (industrial and military).
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect CANFD0 and CANFD1 on the Versal-virt machine and update xlnx-versal-virt
document with CANFD command line examples.
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xilinx Versal CANFD controller is developed based on SocketCAN, QEMU CAN bus
implementation. Bus connection and socketCAN connection for each CAN module
can be set through command lines.
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function is unused since commit
bdad3654d3 ('hw/arm/nseries: Remove
invalid/unnecessary n8x0_uart_setup()').
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230523195608.125820-3-shentey@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
As per "Loongson 3A5000/3B5000 Processor Reference Manual",
Loongson 3A5000's IPI implementation have 4 mailboxes per
core.
However, in 78464f023b ("hw/loongarch/virt: Modify ipi as
percpu device"), the number of IPI mailboxes was reduced to
one, which mismatches actual hardware.
It won't affect LoongArch based system as LoongArch boot code
only uses the first mailbox, however MIPS based Loongson boot
code uses all 4 mailboxes.
Fixes Coverity CID: 1512452, 1512453
Fixes: 78464f023b ("hw/loongarch/virt: Modify ipi as percpu device")
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230521102307.87081-2-jiaxun.yang@flygoat.com>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Now we no longer have dynamic state affecting things we can remove the
additional fields in cpu.h and simplify the TB hash calculation.
For the benchmark:
hyperfine -w 2 -m 20 \
"./arm-softmmu/qemu-system-arm -cpu cortex-a15 \
-machine type=virt,highmem=off \
-display none -m 2048 \
-serial mon:stdio \
-netdev user,id=unet,hostfwd=tcp::2222-:22 \
-device virtio-net-pci,netdev=unet \
-device virtio-scsi-pci \
-blockdev driver=raw,node-name=hd,discard=unmap,file.driver=host_device,file.filename=/dev/zen-disk/debian-bullseye-armhf \
-device scsi-hd,drive=hd -smp 4 \
-kernel /home/alex/lsrc/linux.git/builds/arm/arch/arm/boot/zImage \
-append 'console=ttyAMA0 root=/dev/sda2 systemd.unit=benchmark.service' \
-snapshot"
It has a marginal effect on runtime, before:
Time (mean ± σ): 26.279 s ± 2.438 s [User: 41.113 s, System: 1.843 s]
Range (min … max): 24.420 s … 32.565 s 20 runs
after:
Time (mean ± σ): 24.440 s ± 2.885 s [User: 34.474 s, System: 2.028 s]
Range (min … max): 21.663 s … 29.937 s 20 runs
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1358
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230526165401.574474-10-alex.bennee@linaro.org
Message-Id: <20230524133952.3971948-9-alex.bennee@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
- Fix blockdev-create with iothreads
- Remove aio_disable_external() API
-----BEGIN PGP SIGNATURE-----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=yuER
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://repo.or.cz/qemu/kevin into staging
Block layer patches
- Fix blockdev-create with iothreads
- Remove aio_disable_external() API
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmR2JIARHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9brtA/9HVdAdtJxW78J60TE2lTqE9XlqMOEHBZl
# 8GN72trjP2geY/9mVsv/XoFie4ecqFsYjwAWWUuXZwLgAo53jh7oFN7gBH5iGyyD
# +EukYEfjqoykX5BkoK0gbMZZUe5Y4Dr2CNXYw4bNg8kDzj2RLifGA1XhdL3HoiVt
# PHZrhwBR7ddww6gVOnyJrfGL8fMkW/ZNeKRhrTZuSP+63oDOeGTsTumD+YKJzfPs
# p5WlwkuPjcqbO+w32FeVOHVhNI4swkN5svz3fkr8NuflfA7kH6nBQ5wymObbaTLc
# Erx03lrtP1+6nw43V11UnYt6iDMg4EBUQwtzNaKFnk3rMIdjoQYxIM5FTBWL2rYD
# Dg6PhkncXQ1WNWhUaFqpTFLB52XAYsSa4/y2QAGP6nWbqAUAUknQ3exaMvWiq7Z0
# nZeyyhIWvpJIHGCArWRdqqh+zsBdsmUVuPGyZnZgL/cXoJboYiHMyMJSUWE0XxML
# NGrncwxdsBXkVGGwTdHpBT64dcu3ENRgwtraqRLQm+tp5MKNTJB/+Ug2/p1vonHT
# UOoHz//UPskn8sHIyevoHXeu2Ns0uIHzrAXr+7Ay+9UYyIH6a07F4b2BGqkfyi/i
# 8wQsDmJ/idx5C4q1+jS+GuIbpnjIx6nxXwXMqpscUXZmM4Am8OMkiKxQAa1wExGF
# paId+HHwyks=
# =yuER
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 30 May 2023 09:29:52 AM PDT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin: (32 commits)
aio: remove aio_disable_external() API
virtio: do not set is_external=true on host notifiers
virtio-scsi: implement BlockDevOps->drained_begin()
virtio-blk: implement BlockDevOps->drained_begin()
virtio: make it possible to detach host notifier from any thread
block/fuse: do not set is_external=true on FUSE fd
block/export: don't require AioContext lock around blk_exp_ref/unref()
block/export: rewrite vduse-blk drain code
hw/xen: do not set is_external=true on evtchn fds
xen-block: implement BlockDevOps->drained_begin()
block: drain from main loop thread in bdrv_co_yield_to_drain()
block: add blk_in_drain() API
hw/xen: do not use aio_set_fd_handler(is_external=true) in xen_xenstore
block/export: stop using is_external in vhost-user-blk server
block/export: wait for vhost-user-blk requests when draining
util/vhost-user-server: rename refcount to in_flight counter
virtio-scsi: stop using aio_disable_external() during unplug
virtio-scsi: avoid race between unplug and transport event
hw/qdev: introduce qdev_is_realized() helper
block-backend: split blk_do_set_aio_context()
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The virtio-scsi Host Bus Adapter provides access to devices on a SCSI
bus. Those SCSI devices typically have a BlockBackend. When the
BlockBackend enters a drained section, the SCSI device must temporarily
stop submitting new I/O requests.
Implement this behavior by temporarily stopping virtio-scsi virtqueue
processing when one of the SCSI devices enters a drained section. The
new scsi_device_drained_begin() API allows scsi-disk to message the
virtio-scsi HBA.
scsi_device_drained_begin() uses a drain counter so that multiple SCSI
devices can have overlapping drained sections. The HBA only sees one
pair of .drained_begin/end() calls.
After this commit, virtio-scsi no longer depends on hw/virtio's
ioeventfd aio_set_event_notifier(is_external=true). This commit is a
step towards removing the aio_disable_external() API.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230516190238.8401-19-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a helper function to check whether the device is realized without
requiring the Big QEMU Lock. The next patch adds a second caller. The
goal is to avoid spreading DeviceState field accesses throughout the
code.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230516190238.8401-3-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
As everything is in place, we can use a new system property to
advertise which stage is supported and remove bad_ste from STE
stage2 config.
The property added arm-smmuv3.stage can have 3 values:
- "1": Stage-1 only is advertised.
- "2": Stage-2 only is advertised.
If not passed or an unsupported value is passed, it will default to
stage-1.
Advertise VMID16.
Don't try to decode CD, if stage-2 is configured.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20230516203327.2051088-11-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CMD_TLBI_S2_IPA: As S1+S2 is not enabled, for now this can be the
same as CMD_TLBI_NH_VAA.
CMD_TLBI_S12_VMALL: Added new function to invalidate TLB by VMID.
For stage-1 only commands, add a check to throw CERROR_ILL if used
when stage-1 is not supported.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20230516203327.2051088-9-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow TLB to be tagged with VMID.
If stage-1 is only supported, VMID is set to -1 and ignored from STE
and CMD_TLBI_NH* cmds.
Update smmu_iotlb_insert trace event to have vmid.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20230516203327.2051088-8-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Parse stage-2 configuration from STE and populate it in SMMUS2Cfg.
Validity of field values are checked when possible.
Only AA64 tables are supported and Small Translation Tables (STT) are
not supported.
According to SMMUv3 UM(IHI0070E) "5.2 Stream Table Entry": All fields
with an S2 prefix (with the exception of S2VMID) are IGNORED when
stage-2 bypasses translation (Config[1] == 0).
Which means that VMID can be used(for TLB tagging) even if stage-2 is
bypassed, so we parse it unconditionally when S2P exists. Otherwise
it is set to -1.(only S1P)
As stall is not supported, if S2S is set the translation would abort.
For S2R, we reuse the same code used for stage-1 with flag
record_faults. However when nested translation is supported we would
need to separate stage-1 and stage-2 faults.
Fix wrong shift in STE_S2HD, STE_S2HA, STE_S2S.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20230516203327.2051088-6-smostafa@google.com
[PMM: fixed format string]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for adding stage-2 support, rename smmu_ptw_64 to
smmu_ptw_64_s1 and refactor some of the code so it can be reused in
stage-2 page table walk.
Remove AA64 check from PTW as decode_cd already ensures that AA64 is
used, otherwise it faults with C_BAD_CD.
A stage member is added to SMMUPTWEventInfo to differentiate
between stage-1 and stage-2 ptw faults.
Add stage argument to trace_smmu_ptw_level be consistent with other
trace events.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20230516203327.2051088-4-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for adding stage-2 support, add a S2 config
struct(SMMUS2Cfg), composed of the following fields and embedded in
the main SMMUTransCfg:
-tsz: Size of IPA input region (S2T0SZ)
-sl0: Start level of translation (S2SL0)
-affd: AF Fault Disable (S2AFFD)
-record_faults: Record fault events (S2R)
-granule_sz: Granule page shift (based on S2TG)
-vmid: Virtual Machine ID (S2VMID)
-vttb: Address of translation table base (S2TTB)
-eff_ps: Effective PA output range (based on S2PS)
They will be used in the next patches in stage-2 address translation.
The fields in SMMUS2Cfg, are reordered to make the shared and stage-1
fields next to each other, this reordering didn't change the struct
size (104 bytes before and after).
Stage-1 only fields: aa64, asid, tt, ttb, tbi, record_faults, oas.
oas is stage-1 output address size. However, it is used to check
input address in case stage-1 is unimplemented or bypassed according
to SMMUv3 manual IHI0070.E "3.4. Address sizes"
Shared fields: stage, disabled, bypassed, aborted, iotlb_*.
No functional change intended.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20230516203327.2051088-3-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SNVS is supported on both i.MX6 and i.MX6UL and is needed
to support shutdown on the board.
Cc: Peter Maydell <peter.maydell@linaro.org> (odd fixer:SABRELITE / i.MX6)
Cc: Jean-Christophe Dubois <jcd@tribudubois.net> (reviewer:SABRELITE / i.MX6)
Cc: qemu-arm@nongnu.org (open list:SABRELITE / i.MX6)
Cc: qemu-devel@nongnu.org (open list:All patches CC here)
Signed-off-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Message-id: 20230515095015.66860-1-cheptsov@ispras.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This queue includes several assorted fixes for PowerPC SPR
emulation, a change in the default Pegasos2 CPU, the addition
of AIL mode 3 for spapr, a PIC->CPU interrupt fix for prep and
performance enhancements in fpu_helper.c.
-----BEGIN PGP SIGNATURE-----
iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZHOFiRYcZGFuaWVsaGI0
MTNAZ21haWwuY29tAAoJEDzZypbeAzFkVZ0BAMV+9RlHKRlldOSPMEWCWo6hmA/U
9SMyJsZPY3OpDbE3AP9XOQR1boqyT5MJXoeOUq1OLlFm6mY7UA300kBZ7wxVCw==
=IGNT
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20230528' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2023-05-28:
This queue includes several assorted fixes for PowerPC SPR
emulation, a change in the default Pegasos2 CPU, the addition
of AIL mode 3 for spapr, a PIC->CPU interrupt fix for prep and
performance enhancements in fpu_helper.c.
# -----BEGIN PGP SIGNATURE-----
#
# iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZHOFiRYcZGFuaWVsaGI0
# MTNAZ21haWwuY29tAAoJEDzZypbeAzFkVZ0BAMV+9RlHKRlldOSPMEWCWo6hmA/U
# 9SMyJsZPY3OpDbE3AP9XOQR1boqyT5MJXoeOUq1OLlFm6mY7UA300kBZ7wxVCw==
# =IGNT
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 28 May 2023 09:47:05 AM PDT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20230528' of https://gitlab.com/danielhb/qemu:
ppc/pegasos2: Change default CPU to 7457
target/ppc: Add POWER9 DD2.2 model
target/ppc: Merge COMPUTE_CLASS and COMPUTE_FPRF
pnv_lpc: disable reentrancy detection for lpc-hc
target/ppc: Use SMT4 small core chip type in POWER9/10 PVRs
hw/ppc/prep: Fix wiring of PIC -> CPU interrupt
spapr: Add SPAPR_CAP_AIL_MODE_3 for AIL mode 3 support for H_SET_MODE hcall
target/ppc: Alignment faults do not set DSISR in ISA v3.0 onward
target/ppc: Fix width of some 32-bit SPRs
target/ppc: Fix fallback to MFSS for MFFS* instructions on pre 3.0 ISAs
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
POWER9 DD2.1 and earlier had significant limitations when running KVM,
including lack of "mixed mode" MMU support (ability to run HPT and RPT
mode on threads of the same core), and a translation prefetch issue
which is worked around by disabling "AIL" mode for the guest.
These processors are not widely available, and it's difficult to deal
with all these quirks in qemu +/- KVM, so create a POWER9 DD2.2 CPU
and make it the default POWER9 CPU.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Message-Id: <20230515160201.394587-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The behaviour of the Address Translation Mode on Interrupt resource is
not consistently supported by all CPU versions or all KVM versions: KVM
HV does not support mode 2, and does not support mode 3 on POWER7 or
early POWER9 processesors. KVM PR only supports mode 0. TCG supports all
modes (0, 2, 3) on CPUs with support for the corresonding LPCR[AIL] mode.
This leads to inconsistencies in guest behaviour and could cause problems
migrating guests.
This was not noticable for Linux guests for a long time because the
kernel only uses modes 0 and 3, and it used to consider AIL-3 to be
advisory in that it would always keep the AIL-0 vectors around, so it
did not matter whether or not interrupts were delivered according to
the AIL mode. Recent Linux guests depend on AIL mode 3 working as
specified in order to support the SCV facility interrupt. If AIL-3 can
not be provided, then H_SET_MODE must return an error to Linux so it can
disable the SCV facility (failure to do so can lead to userspace being
able to crash the guest kernel).
Add the ail-mode-3 capability to specify that AIL-3 is supported. AIL-0
is implied as the baseline, and AIL-2 is no longer supported by spapr.
AIL-2 is not known to be used by any software, but support in TCG could
be restored with an ail-mode-2 capability quite easily if a regression
is reported.
Modify the H_SET_MODE Address Translation Mode on Interrupt resource
handler to check capabilities and correctly return error if not
supported.
KVM has a cap to advertise support for AIL-3.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230515160216.394612-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add a virtio-multitouch device to the family of devices emulated by
virtio-input implementing the Multi-touch protocol as descripted here:
https://www.kernel.org/doc/html/latest/input/multi-touch-protocol.html?highlight=multi+touch
This patch just add the device itself, without connecting it to any
backends. The following patches will add a PCI-based multitouch device,
some helpers in "ui" and will enable the GTK3 backend to transpose
multi-touch events from the host to the guest.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230526112925.38794-4-slp@redhat.com>
We are going to require the macro from other files, too, so move
this #define to the header file.
Message-Id: <20230512124033.502654-9-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are going to re-use this setting for other targets, so let's
move this to the main MachineClass.
Message-Id: <20230512124033.502654-4-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Now that the RTC is created as part of the southbridges it doesn't need
to be an out-parameter any longer.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230519084734.220480-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Just like in the real hardware (and in PIIX4), create the RTC
controllers in the south bridges.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230519084734.220480-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are new users of this functionality coming shortly so factor
it out from the GET_TIMESTAMP mailbox command handling.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230423162013.4535-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to PCIe Address Translation Services specification 5.1.3.,
ATS Control Register has Enable bit to enable/disable ATS. Guest may
enable/disable PCI ATS and, accordingly, Device-TLB for the VirtIO PCI
device. So, raise/lower a flag and call a trigger function to pass this
event to a device implementation.
Signed-off-by: Viktor Prutyanov <viktor@daynix.com>
Message-Id: <20230512135122.70403-2-viktor@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Unlike pam_update() which takes the subject -- PAMMemoryRegion -- as
first argument, init_pam() takes it as fifth (!) argument. This makes it
quite hard to figure out what an init_pam() invocation actually
initializes. By moving the subject to the front this should become
clearer.
While at it, lower the DeviceState parameter to Object, also
communicating more clearly that this parameter is just the owner rather
than some (heavy?) dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213162004.2797-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Going through pc_memory_init() seems quite complicated for a simple
assignment.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213162004.2797-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
1. The vIOMMU support will make vDPA can work in IOMMU mode. This
will fix security issues while using the no-IOMMU mode.
To support this feature we need to add new functions for IOMMU MR adds and
deletes.
Also since the SVQ does not support vIOMMU yet, add the check for IOMMU
in vhost_vdpa_dev_start, if the SVQ and IOMMU enable at the same time
the function will return fail.
2. Skip the iova_max check vhost_vdpa_listener_skipped_section(). While
MR is IOMMU, move this check to vhost_vdpa_iommu_map_notify()
Verified in vp_vdpa and vdpa_sim_net driver
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20230510054631.2951812-5-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support vIOMMU in vdpa, need to exposed the function
vhost_dev_has_iommu, vdpa will use this function to check
if vIOMMU enable.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20230510054631.2951812-2-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since it's implementation on v8.0.0-rc0, having the PCI_ERR_UNCOR_MASK
set for machine types < 8.0 will cause migration to fail if the target
QEMU version is < 8.0.0 :
qemu-system-x86_64: get_pci_config_device: Bad config data: i=0x10a read: 40 device: 0 cmask: ff wmask: 0 w1cmask:0
qemu-system-x86_64: Failed to load PCIDevice:config
qemu-system-x86_64: Failed to load e1000e:parent_obj
qemu-system-x86_64: error while loading state for instance 0x0 of device '0000:00:02.0/e1000e'
qemu-system-x86_64: load of migration failed: Invalid argument
The above test migrated a 7.2 machine type from QEMU master to QEMU 7.2.0,
with this cmdline:
./qemu-system-x86_64 -M pc-q35-7.2 [-incoming XXX]
In order to fix this, property x-pcie-err-unc-mask was introduced to
control when PCI_ERR_UNCOR_MASK is enabled. This property is enabled by
default, but is disabled if machine type <= 7.2.
Fixes: 010746ae1d ("hw/pci/aer: Implement PCI_ERR_UNCOR_MASK register")
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Message-Id: <20230503002701.854329-1-leobras@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1576
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit enables each CXL Type-3 device to contain one volatile
memory region and one persistent region.
Two new properties have been added to cxl-type3 device initialization:
[volatile-memdev] and [persistent-memdev]
The existing [memdev] property has been deprecated and will default the
memory region to a persistent memory region (although a user may assign
the region to a ram or file backed region). It cannot be used in
combination with the new [persistent-memdev] property.
Partitioning volatile memory from persistent memory is not yet supported.
Volatile memory is mapped at DPA(0x0), while Persistent memory is mapped
at DPA(vmem->size), per CXL Spec 8.2.9.8.2.0 - Get Partition Info.
Signed-off-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230421160827.2227-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In some spots, it would be helpful to be able to use TARGET_NAME
in common (target independent) code, too. Thus introduce a wrapper
that can be called from common code, too, just like we already
have one for target_words_bigendian().
Message-Id: <20230424160434.331175-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
For being able to create a universal QEMU binary one day, core
files like machine-qmp-cmds.c must not contain any "#ifdef TARGET_..."
parts. Thus let's provide the target specific function via a
function pointer in CPUClass instead, as a first step towards
making this file target independent.
Message-Id: <20230424160434.331175-2-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Kernel commit 292a7d6fca33 ("KVM: s390: pv: fix asynchronous teardown
for small VMs") causes the KVM_PV_ASYNC_CLEANUP_PREPARE ioctl to fail
if the VM is not larger than 2GiB. QEMU would attempt it and fail,
print an error message, and then proceed with a normal teardown.
Avoid attempting to use asynchronous teardown altogether when the VM is
not larger than 2 GiB. This will avoid triggering the error message and
also avoid pointless overhead; normal teardown is fast enough for small
VMs.
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Fixes: c3a073c610 ("s390x/pv: Add support for asynchronous teardown for reboot")
Link: https://lore.kernel.org/all/20230421085036.52511-2-imbrenda@linux.ibm.com/
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20230510105531.30623-2-imbrenda@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Fix inline function parameter in pv.h]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The lifetime of the PCIBridgeWindows instance accessed via the windows pointer
in struct PCIBridge is managed separately from the PCIBridge itself.
Triggered by ./qemu-system-x86_64 -M x-remote -display none -monitor stdio
QEMU monitor: device_add cxl-downstream
In some error handling paths (such as the above due to attaching a cxl-downstream
port anything other than a cxl-upstream port) the g_free() of the PCIBridge
windows in pci_bridge_region_cleanup() is called before the final call of
flatview_uref() in address_space_set_flatview() ultimately from
drain_call_rcu()
At one stage this resulted in a crash, currently can still be observed using
valgrind which records a use after free.
When present, only one instance is allocated. pci_bridge_update_mappings()
can operate directly on an instance rather than creating a new one and
swapping it in. Thus there appears to be no reason to not directly
couple the lifetimes of the two structures by embedding the PCIBridgeWindows
within the PCIBridge removing the need for the problematic separate free.
Patch is same as was posted deep in the discussion.
https://lore.kernel.org/qemu-devel/20230403171232.000020bb@huawei.com/
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230421122550.28234-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add separate macro EXTIOI_CPUS for extioi interrupt controller, extioi
only supports 4 cpu. And set macro LOONGARCH_MAX_CPUS as 256 so that
loongarch virt machine supports more cpus.
Interrupts from external devices can only be routed cpu 0-3 because
of extioi limits, cpu internal interrupt such as timer/ipi can be
triggered on all cpus.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230512100421.1867848-3-gaosong@loongson.cn>
ipi is used to communicate between cpus, this patch modified
loongarch ipi device as percpu device, so that there are
2 MemoryRegions with ipi device, rather than 2*cpus
MemoryRegions, which may be large than QDEV_MAX_MMIO if
more cpus are added on loongarch virt machine.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230512100421.1867848-2-gaosong@loongson.cn>
Add signature and signature-granularity properties in spike to specify the target
signatrue file and the line size for signature data.
Recgonize the signature section between begin_signature and end_signature symbols
when loading elf of ACT tests. Then dump signature data in signature section just
before the ACT tests exit.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230405095720.75848-2-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The arm boot.c code includes a utility function write_bootloader()
which assists in writing a boot-code fragment into guest memory,
including handling endianness and fixing it up with entry point
addresses and similar things. This is useful not just for the boot.c
code but also in board model code, so rename it to
arm_write_bootloader() and make it globally visible.
Since we are making it public, make its API a little neater: move the
AddressSpace* argument to be next to the hwaddr argument, and allow
the fixupcontext array to be const, since we never modify it in this
function.
Cc: qemu-stable@nongnu.org
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230424152717.1333930-2-peter.maydell@linaro.org
[PMM: Split out from another patch by Cédric, added doc comment]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This query copies the kernel command line into the message buffer. It
was previously stubbed out to return empty, this commit makes it reflect
the arguments specified with `-append`.
I observed the following peculiarities on my Pi 3B+:
- If the buffer is shorter than the string, the response header gives
the full length, but no data is actually copied.
- No NUL terminator is added: even if the buffer is long enough to fit
one, the buffer's original contents are preserved past the string's
end.
- The VC firmware adds the following extra parameters beside the
user-supplied ones (via /boot/cmdline.txt): `video`, `vc_mem.mem_base`
and `vc_mem.mem_size`. This is currently not implemented in qemu.
Signed-off-by: Daniel Bertalan <dani@danielbertalan.dev>
Message-id: 20230425103250.56653-1-dani@danielbertalan.dev
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added comment about NUL and short-buffer behaviour]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mostly just fixes, cleanups all over the place.
Some optimizations.
More control over slot_reserved_mask.
More feature bits supported for SVQ.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmRHQvAPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpQc0H/RD+RXy7IAnmhkdCyjj0hM8pftPTwCJfrSCW
DLHP4c5jiKO5ngUoAv3YJdM77TBCXlJn6gceeKBrzhGUTtJ7dTLC+Udeq/jW43EF
/E2ldLLbTNFyUqW8yX7D+EVio7Jy4zXTHpczKCF5vO7MaVWS/b3QdCpmjXpEHLNb
janv24vQHHgmRwK96uIdIauJJT8aqYW0arn1po8anxuFS8ok9Tf8LTEF5uBHokJP
MriTwMaqMgRK+4rzh+b6wc7QC5GqIr44gFrsfFYuNOUY0+BizvGvUAtMt+B/XZwt
OF4RSShUh2bhsQoYwgvShfEsR/vWwOl3yMAhcsB+wMgMzMG8MUQ=
=e8DF
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: fixes, features, cleanups
Mostly just fixes, cleanups all over the place.
Some optimizations.
More control over slot_reserved_mask.
More feature bits supported for SVQ.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmRHQvAPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpQc0H/RD+RXy7IAnmhkdCyjj0hM8pftPTwCJfrSCW
# DLHP4c5jiKO5ngUoAv3YJdM77TBCXlJn6gceeKBrzhGUTtJ7dTLC+Udeq/jW43EF
# /E2ldLLbTNFyUqW8yX7D+EVio7Jy4zXTHpczKCF5vO7MaVWS/b3QdCpmjXpEHLNb
# janv24vQHHgmRwK96uIdIauJJT8aqYW0arn1po8anxuFS8ok9Tf8LTEF5uBHokJP
# MriTwMaqMgRK+4rzh+b6wc7QC5GqIr44gFrsfFYuNOUY0+BizvGvUAtMt+B/XZwt
# OF4RSShUh2bhsQoYwgvShfEsR/vWwOl3yMAhcsB+wMgMzMG8MUQ=
# =e8DF
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 25 Apr 2023 04:03:12 AM BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (31 commits)
hw/pci-bridge: Make PCIe and CXL PXB Devices inherit from TYPE_PXB_DEV
hw/pci-bridge: pci_expander_bridge fix type in pxb_cxl_dev_reset()
docs/specs: Convert pci-testdev.txt to rst
docs/specs: Convert pci-serial.txt to rst
docs/specs/pci-ids: Convert from txt to rST
acpi: pcihp: allow repeating hot-unplug requests
virtio: i2c: Check notifier helpers for VIRTIO_CONFIG_IRQ_IDX
docs: Remove obsolete descriptions of SR-IOV support
intel_iommu: refine iotlb hash calculation
docs/cxl: Fix sentence
MAINTAINERS: Add Eugenio Pérez as vhost-shadow-virtqueue reviewer
tests: bios-tables-test: replace memset with initializer
hw/acpi: limit warning on acpi table size to pc machines older than version 2.3
Add my old and new work email mapping and use work email to support acpi
vhost-user-blk-server: notify client about disk resize
pci: avoid accessing slot_reserved_mask directly outside of pci.c
hw: Add compat machines for 8.1
hw/i386/amd_iommu: Factor amdvi_pci_realize out of amdvi_sysbus_realize
hw/i386/amd_iommu: Set PCI static/const fields via PCIDeviceClass
hw/i386/amd_iommu: Move capab_offset from AMDVIState to AMDVIPCIState
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Previously, PXB_CXL_DEVICE, PXB_PCIE_DEVICE and PXB_DEVICE all
have PCI_DEVICE as their direct parent but share a common state
struct PXBDev. convert_to_pxb() is used to get the PXBDev
instance from which ever of these types it is called on.
This patch switches to an explicit hierarchy based on shared
functionality. To allow use of OBJECT_DECLARE_SIMPLE_TYPE()
whilst minimizing code changes, all types are renamed to have
the postfix _DEV rather than _DEVICE. The new heirarchy
has PXB_CXL_DEV with parent PXB_PCIE_DEV which in turn
has parent PXB_DEV which continues to have parent PCI_DEVICE.
This allows simple use of PXB_DEV() etc rather than a custom function
+ removal of duplicated properties and moving the CXL specific
elements out of struct PXBDev.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230420142750.6950-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
i440fx machine versions 2.3 and newer supports dynamic ram
resizing. See commit a1666142db ("acpi-build: make ROMs RAM blocks resizeable") .
Currently supported all q35 machine types (versions 2.4 and newer) supports
resizable RAM/ROM blocks.Therefore the warning generated when the ACPI table
size exceeds a pre-defined value does not apply to those machine versions.
Add a check limiting the warning message to only those machines that does not
support expandable ram blocks (that is, i440fx machines with version 2.2
and older).
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20230329045726.14028-1-anisinha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAmRBLgoACgkQda1lgCoL
QhEPyQf/WfEg8k2hDLExobsSgup1IsnT+mHHTBOZVJvq2efg2YXUTHA56fmD9X6d
crqTq68L5oaMES5iYEZhA7EAgfk3RvxDQGrlXBByPzrc6SSwEHHMR4Zzi5zrbCoW
t6TmaKQrlQqYwkhhsbyqnG46bj0ugCDagkBLfJdVl96fjkYgTspcDxaNwqwy/DPn
GTmQlvdRY09D1nylIdtcLBIfsM+sIkRslyngbUEIy+Bx8EWRy2a8Qw0BdY9g1XoE
e0CaRaFMpju1KOIjq0YSIzt0LSQDFfPc1IlUAC0ZALhNmp+PPNtr4E7+4kFfO2ym
1sT2w25ho8dYDdm/m8tIauCdGoHw4A==
=ML27
-----END PGP SIGNATURE-----
Merge tag 'pull-tpm-2023-04-20-1' of https://github.com/stefanberger/qemu-tpm into staging
Merge tpm 2023/04/20 v1
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAmRBLgoACgkQda1lgCoL
# QhEPyQf/WfEg8k2hDLExobsSgup1IsnT+mHHTBOZVJvq2efg2YXUTHA56fmD9X6d
# crqTq68L5oaMES5iYEZhA7EAgfk3RvxDQGrlXBByPzrc6SSwEHHMR4Zzi5zrbCoW
# t6TmaKQrlQqYwkhhsbyqnG46bj0ugCDagkBLfJdVl96fjkYgTspcDxaNwqwy/DPn
# GTmQlvdRY09D1nylIdtcLBIfsM+sIkRslyngbUEIy+Bx8EWRy2a8Qw0BdY9g1XoE
# e0CaRaFMpju1KOIjq0YSIzt0LSQDFfPc1IlUAC0ZALhNmp+PPNtr4E7+4kFfO2ym
# 1sT2w25ho8dYDdm/m8tIauCdGoHw4A==
# =ML27
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 20 Apr 2023 01:20:26 PM BST
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* tag 'pull-tpm-2023-04-20-1' of https://github.com/stefanberger/qemu-tpm:
qtest: Add a test case for TPM TIS I2C connected to Aspeed I2C controller
qtest: Move tpm_util_tis_transmit() into tpm-tis-utils.c and rename it
qtest: Add functions for accessing devices on Aspeed I2C controller
tests/avocado/aspeed: Add TPM TIS I2C test
tpm: Add support for TPM device over I2C bus
tpm: Extend common APIs to support TPM TIS I2C
docs: Add support for TPM devices over I2C bus
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Allow setting a chardev input file on the command line
* Fix .travis.yml to work with non-public Travis instances, too
* Move a lot of code from specifc_ss into softmmu_ss
* Add a test case for TPM TIS I2C connected to Aspeed I2C controller
* Update tests/vm/freebsd to version 13
* Some more misc minor fixes here and there
-----BEGIN PGP SIGNATURE-----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=8ZFL
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-04-20' of https://gitlab.com/thuth/qemu into staging
* Compat machines for version 8.1
* Allow setting a chardev input file on the command line
* Fix .travis.yml to work with non-public Travis instances, too
* Move a lot of code from specifc_ss into softmmu_ss
* Add a test case for TPM TIS I2C connected to Aspeed I2C controller
* Update tests/vm/freebsd to version 13
* Some more misc minor fixes here and there
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmRBDtMRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXfjw//UYytlyZsDOLAMfFNGQViMmVf29KbrDRe
# doDh4Nl1oZLNKm9C5XlQExhsRbLm6Hi9nyQvSCJs4CvZ1jBY6U7GfgMNIaozXWb3
# 4gQyJb9ACe/z8bQmPUVF2sdW1QZ9zpf8LWpCOTGUZiI2Tevzkz7b/F5ZxiQiseG6
# dXe8UIwdZhG4jz2+6viqjHiGlKoBkegGYoJthcwnR07aRz2woiNr7rKRiJEiv2G7
# UfMVB96uLkpEhaDoohz440/rjviazO1nt6HDvgEajXT1X5P/8phT9IvT7olAZXZH
# R2Qm6YyYcSWavoPms3AryAWG8FjomcyBjuebfAVW5/x+fl/401sn9quBMoZrYPEX
# dfzF64vVokdXNQEH6+qc95PdB6/+d0CZPY8ilMRtAttf2sMw7IgqhG3zDLbj9t6R
# dns2/DY9zu2pp07IEAXn/iVbW4rl2HADUQncr6B/cPy++lYiFvv7LX8OE+YWOsk0
# gvxzYx6rRhr5j7xT1sP30pLwsG3mX7qRDfba1Bt19CzSbu7UGN+w+S1xclgZDoqE
# 0AZIeVUuqqNTEoBLoa2xHUDGs9NjeI2+qIh0R5csS/bqDscLXj0cOluvJO48n4Rt
# +SGQSCSmU/lxn6EbBz4tw3orlp0clBH9fEaSg9lYxuUTYvQOpdYS7u4d63VQFvzp
# dwQ9LRDFNsA=
# =8ZFL
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 20 Apr 2023 11:07:15 AM BST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [undefined]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-04-20' of https://gitlab.com/thuth/qemu: (23 commits)
tests/vm/freebsd: Update to FreeBSD 13.2
qtest: Add a test case for TPM TIS I2C connected to Aspeed I2C controller
qtest: Move tpm_util_tis_transmit() into tpm-tis-utils.c and rename it
qtest: Add functions for accessing devices on Aspeed I2C controller
MAINTAINERS: Add Juan Quintela to developer guides review
cpu: Remove parameter of list_cpus()
hw/core: Move numa.c into the target independent source set
softmmu: Move dirtylimit.c into the target independent source set
hw/display: Compile vga.c as target-independent code
softmmu: Make qtest.c target independent
include/exec: Provide the tswap() functions for target independent code, too
softmmu/qtest: Move the target-specific pseries RTAS code out of qtest.c
hw/char: Move two more files from specific_ss to softmmu_ss
target/i386: Set family/model/stepping of the "max" CPU according to LM bit
tests/migration: Only run auto_converge in slow mode
travis.yml: Add missing 'flex', 'bison' packages to 'GCC (user)' job
travis.yml: Add missing clang-10 package to the 'Clang (disable-tcg)' job
chardev: Allow setting file chardev input file on the command line
qtest: Don't assert on "-qtest chardev:myid"
test: Fix test-crypto-secret when compiling without keyring support
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch provides accessor functions as replacements for direct
access to slot_reserved_mask according to the comment at the top
of include/hw/pci/pci_bus.h which advises that data structures for
PCIBus should not be directly accessed but instead be accessed using
accessor functions in pci.h.
Three accessor functions can conveniently replace all direct accesses
of slot_reserved_mask. With this patch, the new accessor functions are
used in hw/sparc64/sun4u.c and hw/xen/xen_pt.c and pci_bus.h is removed
from the included header files of the same two files.
No functional change intended.
Signed-off-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <b1b7f134883cbc83e455abbe5ee225c71aa0e8d0.1678888385.git.brchuckz@aol.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [sun4u]
Add 8.1 machine types for arm/i440fx/m68k/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20230314173009.152667-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Optimize the virtio-balloon feature on the ARM platform by adding
a variable to keep track of the current hot-plugged pc-dimm size,
instead of traversing the virtual machine's memory modules to count
the current RAM size during the balloon inflation or deflation
process. This variable can be updated only when plugging or unplugging
the device, which will result in an increase of approximately 60%
efficiency of balloon process on the ARM platform.
We tested the total amount of time required for the balloon inflation process on ARM:
inflate the balloon to 64GB of a 128GB guest under stress.
Before: 102 seconds
After: 42 seconds
Signed-off-by: Qi Xi <xiqi2@huawei.com>
Signed-off-by: Ming Yang yangming73@huawei.com
Message-Id: <e13bc78f96774bfab4576814c293aa52@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
When a virtqueue size is changed by the guest via
virtio_queue_set_num(), its region cache is not automatically updated.
If the size was increased, this could lead to accessing the cache out
of bounds. For example, in vring_get_used_event():
static inline uint16_t vring_get_used_event(VirtQueue *vq)
{
return vring_avail_ring(vq, vq->vring.num);
}
static inline uint16_t vring_avail_ring(VirtQueue *vq, int i)
{
VRingMemoryRegionCaches *caches = vring_get_region_caches(vq);
hwaddr pa = offsetof(VRingAvail, ring[i]);
if (!caches) {
return 0;
}
return virtio_lduw_phys_cached(vq->vdev, &caches->avail, pa);
}
vq->vring.num will be greater than caches->avail.len, which will
trigger a failed assertion down the call path of
virtio_lduw_phys_cached().
Fix this by calling virtio_init_region_cache() after
virtio_queue_set_num() if we are not already calling
virtio_queue_set_rings(). In the legacy path this is already done by
virtio_queue_update_rings().
Signed-off-by: Carlos López <clopez@suse.de>
Message-Id: <20230317002749.27379-1-clopez@suse.de>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add read and write functions for accessing registers of I2C devices
connected to the Aspeed I2C controller.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ninad Palsule <ninad@linux.ibm.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20230331173051.3857801-2-stefanb@linux.ibm.com
Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices.
This commit includes changes for the common code.
- Added support for the new checksum registers which are required for
the I2C support. The checksum calculation is handled in the qemu
common code.
- Added wrapper function for read and write data so that I2C code can
call it without MMIO interface.
The TPM TIS I2C spec describes in the table in section "Interface Locality
Usage per Register" that the TPM_INT_ENABLE and TPM_INT_STATUS registers
must be writable for any locality even if the locality is not the active
locality. Therefore, remove the checks whether the writing locality is the
active locality for these registers.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Message-id: 20230414220754.1191476-3-ninadpalsule@us.ibm.com
Add fec[12]-phy-connected properties and use it to set phy-connected
and phy-consumer properties for imx_fec.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20230315145248.1639364-5-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add fec[12]-phy-connected properties and use it to set phy-connected
and phy-consumer properties for imx_fec.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20230315145248.1639364-3-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SOC on i.MX6UL and i.MX7 has 2 Ethernet interfaces. The PHY on each may
be connected to separate MDIO busses, or both may be connected on the same
MDIO bus using different PHY addresses. Commit 461c51ad42 ("Add a phy-num
property to the i.MX FEC emulator") added support for specifying PHY
addresses, but it did not provide support for linking the second PHY on
a given MDIO bus to the other Ethernet interface.
To be able to support two PHY instances on a single MDIO bus, two properties
are needed: First, there needs to be a flag indicating if the MDIO bus on
a given Ethernet interface is connected. If not, attempts to read from this
bus must always return 0xffff. Implement this property as phy-connected.
Second, if the MDIO bus on an interface is active, it needs a link to the
consumer interface to be able to provide PHY access for it. Implement this
property as phy-consumer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20230315145248.1639364-2-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add read and write functions for accessing registers of I2C devices
connected to the Aspeed I2C controller.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ninad Palsule <ninad@linux.ibm.com>
Message-Id: <20230331173051.3857801-2-stefanb@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch adds WDT to Allwinner-H3 and Orangepi-PC.
WDT is added as an overlay to the Timer module memory area.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds WDT to Allwinner-A10 and Cubieboard.
WDT is added as an overlay to the Timer module memory map.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-3-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds basic support for Allwinner WDT.
Both sun4i and sun6i variants are supported.
However, interrupt generation is not supported, so WDT can be used only to trigger system reset.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-2-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Migrate rtc_ref (which only needs to be 32-bit because it is summed to
a 32-bit register), which requires bumping the migration version.
The HPPA machine does not have versioned machine types so it is okay
to block migration to old versions of QEMU.
While at it, drop the write-only field rtc from LasiState.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CPU watchpoints can be use by non-TCG accelerators.
KVM uses them:
$ git grep CPUWatchpoint|fgrep kvm
target/arm/kvm64.c:1558: CPUWatchpoint *wp = find_hw_watchpoint(cs, debug_exit->far);
target/i386/kvm/kvm.c:5216:static CPUWatchpoint hw_watchpoint;
target/ppc/kvm.c:443:static CPUWatchpoint hw_watchpoint;
target/s390x/kvm/kvm.c:139:static CPUWatchpoint hw_watchpoint;
See for example commit e4482ab7e3 ("target-arm: kvm - add support
for HW assisted debug"):
This adds basic support for HW assisted debug. The ioctl interface
to KVM allows us to pass an implementation defined number of break
and watch point registers. [...]
This partially reverts commit 2609ec2868.
Fixes: 2609ec2868 ("softmmu: Extract watchpoint API from physmem.c")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230328173117.15226-4-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Both cpu_check_watchpoint() and cpu_watchpoint_address_matches()
are specific to TCG system emulation. Declare them in "tcg-cpu-ops.h"
to be sure accessing them from non-TCG code is a compilation error.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230328173117.15226-2-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Bring the block files in line with the QEMU coding style, with spaces
for indentation. This patch partially resolves the issue 371.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/371
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230314095001.13801-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Bring the block files in line with the QEMU coding style, with spaces
for indentation. This patch partially resolves the issue 371.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/371
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230315043229.62100-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The usage in hw/core/cpu.h only requires QEMU_PLUGIN_EV_MAX.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230310195252.210956-7-richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230315174331.2959-17-alex.bennee@linaro.org>
Reviewed-by: Emilio Cota <cota@braap.org>
Bring the files in line with the QEMU coding style, with spaces
for indentation.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/378
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230315032649.57568-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Several features that landed at the last possible moment:
Passthrough HDM decoder emulation
Refactor cryptodev
RAS error emulation and injection
acpi-index support on non-hotpluggable slots
Dynamically switch to vhost shadow virtqueues at vdpa net migration
Plus a couple of bugfixes that look important to have in the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQJ8TYPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp37YIAMpQA5/ddmKKz/ABtBMHB5JX/SVYcG+1xkBR
j9IFYusOfmmDfmgAhv0Qxi9+Wik95lszVZUnphvocSGd0PXH47pK7yv9RZ1ttaYX
oAbXrGqXo8rUhl1ksQsJ8Iasj2di1BLP0byPuozbRkg1Kkz5TqRd9+hBqSBGEx21
tsP5708UVCDAriwYYO78Cx0ZasmB9bqqeom5FdEsg9sYJ5aElOOvitp9YO1p2xhU
gRvhD+k/aqNi+mfOUF7qGDBanxKgx75VV/KU1cjjS9R1vNtwRhfc/26PBrROY00a
wkZWnAxmzDFKRS6cEfeb+eDGEVjC3IqLAjcFeuAIT/78CwdvIiY=
=e1yv
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, fixes
Several features that landed at the last possible moment:
Passthrough HDM decoder emulation
Refactor cryptodev
RAS error emulation and injection
acpi-index support on non-hotpluggable slots
Dynamically switch to vhost shadow virtqueues at vdpa net migration
Plus a couple of bugfixes that look important to have in the release.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQJ8TYPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp37YIAMpQA5/ddmKKz/ABtBMHB5JX/SVYcG+1xkBR
# j9IFYusOfmmDfmgAhv0Qxi9+Wik95lszVZUnphvocSGd0PXH47pK7yv9RZ1ttaYX
# oAbXrGqXo8rUhl1ksQsJ8Iasj2di1BLP0byPuozbRkg1Kkz5TqRd9+hBqSBGEx21
# tsP5708UVCDAriwYYO78Cx0ZasmB9bqqeom5FdEsg9sYJ5aElOOvitp9YO1p2xhU
# gRvhD+k/aqNi+mfOUF7qGDBanxKgx75VV/KU1cjjS9R1vNtwRhfc/26PBrROY00a
# wkZWnAxmzDFKRS6cEfeb+eDGEVjC3IqLAjcFeuAIT/78CwdvIiY=
# =e1yv
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 09 Mar 2023 14:46:14 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (72 commits)
virtio: fix reachable assertion due to stale value of cached region size
hw/virtio/vhost-user: avoid using unitialized errp
hw/pxb-cxl: Support passthrough HDM Decoders unless overridden
hw/pci: Add pcie_count_ds_port() and pcie_find_port_first() helpers
hw/mem/cxl_type3: Add CXL RAS Error Injection Support.
hw/pci/aer: Make PCIE AER error injection facility available for other emulation to use.
hw/cxl: Fix endian issues in CXL RAS capability defaults / masks
hw/mem/cxl-type3: Add AER extended capability
hw/pci-bridge/cxl_root_port: Wire up MSI
hw/pci-bridge/cxl_root_port: Wire up AER
hw/pci/aer: Add missing routing for AER errors
hw/pci/aer: Implement PCI_ERR_UNCOR_MASK register
pcihp: add ACPI PCI hotplug specific is_hotpluggable_bus() callback
pcihp: move fields enabling hotplug into AcpiPciHpState
acpi: pci: move out ACPI PCI hotplug generator from generic slot generator build_append_pci_bus_devices()
acpi: pci: move BSEL into build_append_pcihp_slots()
acpi: pci: drop BSEL usage when deciding that device isn't hotpluggable
pci: move acpi-index uniqueness check to generic PCI device code
tests: acpi: update expected blobs
tests: acpi: add non zero function device with acpi-index on non-hotpluggble bus
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
igb can use this function to change its behavior depending on the
number of virtual functions currently enabled.
Signed-off-by: Gal Hammer <gal.hammer@sap.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
hw/net/mii.h provides common definitions for MII.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
* Deprecate 32-bit x86 and arm hosts for system emulation
* Check bison version to be >= 3.0
* Compile vnc test only if vnc is really enabled
* Check docs/config/ich9-ehci-uhci.cfg via the readconfig-test
* s390x: Add support for list-directed IPL from ECKD DASD
-----BEGIN PGP SIGNATURE-----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=p13b
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-03-07' of https://gitlab.com/thuth/qemu into staging
* Refine the distro support policy
* Deprecate 32-bit x86 and arm hosts for system emulation
* Check bison version to be >= 3.0
* Compile vnc test only if vnc is really enabled
* Check docs/config/ich9-ehci-uhci.cfg via the readconfig-test
* s390x: Add support for list-directed IPL from ECKD DASD
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmQIQD0RHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbX+EA/5ATc/Rz9Y8TZF36/sUKrmjOxQnX91hgRW
# zovgZejoHtek1AC4pLd9kcpo1JonXkOfmbkNRYTw6+1wY6Ipt2apkWAc+MqfvQ80
# dGznbLXnX/E2QHW7h5XqvAhRGvjog9b38zAQcR37PKZ9DkSfWBwMgTT2SXYpLUjR
# YWgqPGBYRq1ViG4q7hv2dHqi/idzh+DOWFGU5NAQC1fEBOmPYN9u6vfbX86dwZsy
# S9pqw16yN2MZKL2bgIViFIjdhPPMO3RFcv8NTPipzk3g/pHNIv58+xCE8r/Tp8LW
# JRQzdh6JbGvj1BXH68igXWGUFW6dhOXZWhgmFe4QEDaiCj91pHGvQCYgo2agx2bl
# rXaSQXSMhIcm+t9C9kO6UNxZf+1HohcM1ZlQXhvX6FcBPVMUx/52YEpiK+OtBKyq
# 43AlKp4fp1xXLFSOyMNgSMR90sksng6CEoQqTr0jCZtF8H18wb+eHfb6dME3XRCw
# SKQeNGhkP1FxaQnlRAkeBxW7GkDE5YBjf9pSIaLZ/8VsLdyo3SK/DLkre5+qnu/V
# lksZlt1K7xDLxRFopBuVJ3MHeFSRazBDbWfrRFOALkdbGEEeZnnmEPFjD3mag+P4
# 1y9WmBJHRLlvhlm195WA8babenUZoOfLkPrL0k7mNLs9sZyx1eIkZfOUgCWjFE2V
# 9VBOWL8oi/w=
# =p13b
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 08 Mar 2023 07:58:53 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-03-07' of https://gitlab.com/thuth/qemu:
pc-bios/s390-ccw: Update s390-ccw.img with the list-directed IPL fix
pc-bios: Add support for List-Directed IPL from ECKD DASD
docs/config: Set the "kvm" accelerator via "[accel]" section
tests/qtest/readconfig: Test docs/config/ich9-ehci-uhci.cfg
tests/qtest/readconfig: Rework test_object_rng_resp into a generic function
gitlab-ci.d/crossbuilds: Drop the 32-bit arm system emulation jobs
docs/about/deprecated: Deprecate 32-bit arm hosts for system emulation
gitlab-ci.d/crossbuilds: Drop the i386 system emulation job
docs/about/deprecated: Deprecate 32-bit x86 hosts for system emulation
include/hw/i386: Clean up includes in x86.h
test: Check vnc enable before compiling vnc test
Hexagon (meson.build): define min bison version
docs/about/build-platforms: Refine the distro support policy
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is phase 2, following on from the basic platform support which was
already merged.
• Add a simple single-tenant internal XenStore implementation
• Indirect Xen gnttab/evtchn/foreignmem/xenstore through operations table
• Provide emulated back ends for Xen operations
• Header cleanups to allow PV back ends to build without Xen itself
• Enable PV back ends in emulated mode
• Documentation update
Tested-by: Paul Durrant <paul@xen.org>
... on real Xen (master branch, 4.18) with a Debian guest.
-----BEGIN PGP SIGNATURE-----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=JGLX
-----END PGP SIGNATURE-----
Merge tag 'xenfv-2' of git://git.infradead.org/users/dwmw2/qemu into staging
Enable PV backends with Xen/KVM emulation
This is phase 2, following on from the basic platform support which was
already merged.
• Add a simple single-tenant internal XenStore implementation
• Indirect Xen gnttab/evtchn/foreignmem/xenstore through operations table
• Provide emulated back ends for Xen operations
• Header cleanups to allow PV back ends to build without Xen itself
• Enable PV back ends in emulated mode
• Documentation update
Tested-by: Paul Durrant <paul@xen.org>
... on real Xen (master branch, 4.18) with a Debian guest.
# -----BEGIN PGP SIGNATURE-----
#
# iQJGBAABCgAwFiEEMUsIrNDeSBEzpfKGm+mA/QrAFUQFAmQHu3wSHGR3bXdAYW1h
# em9uLmNvLnVrAAoJEJvpgP0KwBVE5LYP/0VodDsQdP7Z4L+/IzgBSgEec7qmyQFB
# KlBZS/PmvCZKb0DHLI3GhXIyzD+/fnLtGSRl0rYObnKP7im+MpEDGmn97f6nIITk
# AzkdsVhNEBQFXCkLgQ9y8kTrTmsod9O4sqn0+naa2TX4FPcRN0MaNmpuLEubvaRS
# +JuyHmwy9ZeeAnsU31uJ0nx4F1hW9IDaatNoDeFcFnKCXQp36rtdZUViMowUJvwu
# Q+Xyg6dybusznaoiXd485tTPrTt+FK/wEARse3q2gRh9QblLu0r5BFb0rOfhYCTQ
# jw+5lBsOX+UlffmB9IDakRpVe4RKhvvRQSkRvYkPCshsqud9zMGhaquKg1vKBgca
# I31XSN0LCcon/ahHGtmVAxyZUpWdEnfzO1TbTNpz9oacROklgVgEYdw5Vwca71VD
# SURl6uCt9Jb9WmsR4twus4i4qDjQIDOtOF0hcxpl7HGktkxlGxUVI4qVLXARtVCS
# OTB6N0LlhJ2woj2wYK5BRTiOj03T2MkJEWaYhDdIrQREKWe2Sn4xTOH5kGbQQnOr
# km93odjBZFRHsAUnzXHXW3+yHjMefH7KrHePbmvsO4foGF77bBxosuC2ehFfvNJ0
# VM/H04NDtPYCBwdAr545PSN/q+WzEPQaquLZ0UuTBuPpMMOYd+Ff8YvQWJPyCM18
# 1mq9v6Xe9RQZ
# =JGLX
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 07 Mar 2023 22:32:28 GMT
# gpg: using RSA key 314B08ACD0DE481133A5F2869BE980FD0AC01544
# gpg: issuer "dwmw@amazon.co.uk"
# gpg: Good signature from "David Woodhouse <dwmw@amazon.co.uk>" [unknown]
# gpg: aka "David Woodhouse <dwmw@amazon.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 314B 08AC D0DE 4811 33A5 F286 9BE9 80FD 0AC0 1544
* tag 'xenfv-2' of git://git.infradead.org/users/dwmw2/qemu: (27 commits)
docs: Update Xen-on-KVM documentation for PV disk support
MAINTAINERS: Add entry for Xen on KVM emulation
i386/xen: Initialize Xen backends from pc_basic_device_init() for emulation
hw/xen: Implement soft reset for emulated gnttab
hw/xen: Map guest XENSTORE_PFN grant in emulated Xenstore
hw/xen: Add emulated implementation of XenStore operations
hw/xen: Add emulated implementation of grant table operations
hw/xen: Hook up emulated implementation for event channel operations
hw/xen: Only advertise ring-page-order for xen-block if gnttab supports it
hw/xen: Avoid crash when backend watch fires too early
hw/xen: Build PV backend drivers for CONFIG_XEN_BUS
hw/xen: Rename xen_common.h to xen_native.h
hw/xen: Use XEN_PAGE_SIZE in PV backend drivers
hw/xen: Move xenstore_store_pv_console_info to xen_console.c
hw/xen: Add xenstore operations to allow redirection to internal emulation
hw/xen: Add foreignmem operations to allow redirection to internal emulation
hw/xen: Pass grant ref to gnttab unmap operation
hw/xen: Add gnttab operations to allow redirection to internal emulation
hw/xen: Add evtchn operations to allow redirection to internal emulation
hw/xen: Create initial XenStore nodes
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CXL r3.0 specification allows for there to be no HDM decoders on CXL
Host Bridges if they have only a single root port. Instead, all accesses
directed to the host bridge (as specified in CXL Fixed Memory Windows)
are assumed to be routed to the single root port.
Linux currently assumes this implementation choice. So to simplify testing,
make QEMU emulation also default to no HDM decoders under these particular
circumstances, but provide a hdm_for_passthrough boolean option to have
HDM decoders as previously.
Technically this is breaking backwards compatibility, but given the only
known software stack used with the QEMU emulation is the Linux kernel
and this configuration did not work before this change, there are
unlikely to be any complaints that it now works. The option is retained
to allow testing of software that does allow for these HDM decoders to exist,
once someone writes it.
Reported-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
--
v2: Pick up and fix typo in tag from Fan Ni
Message-Id: <20230227153128.8164-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These two helpers enable host bridges to operate differently depending on
the number of downstream ports, in particular if there is only a single
port.
Useful for CXL where HDM address decoders are allowed to be implicit in
the host bridge if there is only a single root port.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230227153128.8164-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playback channel is supported for now but this is enough to get sound
output from some guests using this device on pegasos2.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <63b99410895312f40e7be479f581da0805e605a1.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Back in the mists of time, before EISA came along and required per-pin
level control in the ELCR register, the i8259 had a single chip-wide
level-mode control in bit 3 of ICW1.
Even in the PIIX3 datasheet from 1996 this is documented as 'This bit is
disabled', but apparently MorphOS is using it in the version of the
i8259 which is in the Pegasos2 board as part of the VT8231 chipset.
It's easy enough to implement, and I think it's harmless enough to do so
unconditionally.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
[balaton: updated commit message as asked by author]
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <3f09b2dd109d19851d786047ad5c2ff459c90cd7.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
QOM objects shouldn't access each other internals fields
except using the QOM API.
mips_cps_realize() instantiates a TYPE_MIPS_ITU object, and
directly sets the 'saar' pointer:
if (saar_present) {
s->itu.saar = &env->CP0_SAAR;
}
In order to avoid that, pass the MIPS_CPU object via a QOM
link property, and set the 'saar' pointer in mips_itu_realize().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20230203113650.78146-10-philmd@linaro.org>
Some length properties are signed, other unsigned:
hw/mips/cps.c:183: DEFINE_PROP_UINT32("num-vp", MIPSCPSState, num_vp, 1),
hw/mips/cps.c:184: DEFINE_PROP_UINT32("num-irq", MIPSCPSState, num_irq, 256),
hw/misc/mips_cmgcr.c:215: DEFINE_PROP_INT32("num-vp", MIPSGCRState, num_vps, 1),
hw/misc/mips_cpc.c:167: DEFINE_PROP_UINT32("num-vp", MIPSCPCState, num_vp, 0x1),
hw/misc/mips_itu.c:552: DEFINE_PROP_INT32("num-fifo", MIPSITUState, num_fifo,
hw/misc/mips_itu.c:554: DEFINE_PROP_INT32("num-semaphores", MIPSITUState,
Since negative values are not used (the minimum is '0'),
unify by declaring all properties as unsigned.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230203113650.78146-9-philmd@linaro.org>
Pick names that align with the section drivers should use them from,
avoiding the confusion of calling a _finalize() function from _exit()
and generalizing the actual _finalize() to handle removing the viommu
blocker.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/167820912978.606734.12740287349119694623.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
CXL uses PCI AER Internal errors to signal to the host that an error has
occurred. The host can then read more detailed status from the CXL RAS
capability.
For uncorrectable errors: support multiple injection in one operation
as this is needed to reliably test multiple header logging support in an
OS. The equivalent feature doesn't exist for correctable errors, so only
one error need be injected at a time.
Note:
- Header content needs to be manually specified in a fashion that
matches the specification for what can be in the header for each
error type.
Injection via QMP:
{ "execute": "qmp_capabilities" }
...
{ "execute": "cxl-inject-uncorrectable-errors",
"arguments": {
"path": "/machine/peripheral/cxl-pmem0",
"errors": [
{
"type": "cache-address-parity",
"header": [ 3, 4]
},
{
"type": "cache-data-parity",
"header": [0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31]
},
{
"type": "internal",
"header": [ 1, 2, 4]
}
]
}}
...
{ "execute": "cxl-inject-correctable-error",
"arguments": {
"path": "/machine/peripheral/cxl-pmem0",
"type": "physical"
} }
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230302133709.30373-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This infrastructure will be reused for CXL RAS error injection
in patches that follow.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230302133709.30373-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
This register in AER should be both writeable and should
have a default value with a couple of the errors masked
including the Uncorrectable Internal Error used by CXL for
it's error reporting.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Message-Id: <20230302133709.30373-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Provide pcihp specific callback to check if bus is hotpluggable
and consolidate its scattered hotplug criteria there.
While at it clean up no longer needed
qbus_set_hotplug_handler(BUS(bus), NULL)
workarounds since callback makes qbus_is_hotpluggable() return
correct answer even if hotplug_handler is set on bus.
PS:
see ("pci: fix 'hotplugglable' property behavior") for details
why callback was introduced.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230302161543.286002-35-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
... instead of duplicating them in piix4 and lpc and then
trying to pass them to pcihp routines as arguments.
it simplifies call sites and places pcihp specific in
its own structure.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230302161543.286002-34-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230302161543.286002-33-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the property may flip its state
during VM bring up or just doesn't work as
the name implies.
In particular with PCIE root port that has
'hotplug={on|off}' property, and when it's
turned off, one would expect
'hotpluggable' == false
for any devices attached to it.
Which is not the case since qbus_is_hotpluggable()
used by the property just checks for presence
of any hotplug_handler set on bus.
The problem is that name BusState::hotplug_handler
from its inception is misnomer, as it handles
not only hotplug but also in many cases coldplug
as well (i.e. generic wiring interface), and
it's fine to have hotplug_handler set on bus
while it doesn't support hotplug (ex. pcie-slot
with hotplug=off).
Another case of root port flipping 'hotpluggable'
state when ACPI PCI hotplug is enabled in this
case root port with 'hotplug=off' starts as
hotpluggable and then later on, pcihp
hotplug_handler clears hotplug_handler
explicitly after checking root port's 'hotplug'
property.
So root-port hotpluggablity check sort of works
if pcihp is enabled but is broken if pcihp is
disabled.
One way to deal with the issue is to ask
hotplug_handler if bus it controls is hotpluggable
or not. To do that add is_hotpluggable_bus()
hook to HotplugHandler interface and use it in
'hotpluggable' property + teach pcie-slot to
actually look into 'hotplug' property state
before deciding if bus is hotpluggable.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230302161543.286002-13-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Devices with CVQ need to migrate state beyond vq state. Leaving this to
future series.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230303172445.1089785-11-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The function vhost.c:vhost_dev_stop calls vhost operation
vhost_dev_start(false). In the case of vdpa it totally reset and wipes
the device, making the fetching of the vring base (virtqueue state) totally
useless.
The kernel backend does not use vhost_dev_start vhost op callback, but
vhost-user do. A patch to make vhost_user_dev_start more similar to vdpa
is desirable, but it can be added on top.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230303172445.1089785-8-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows vhost_vdpa to track if it is safe to get the vring base from
the device or not. If it is not, vhost can fall back to fetch idx from
the guest buffer again.
No functional change intended in this patch, later patches will use this
field.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230303172445.1089785-6-eperezma@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Migrating with vIOMMU will require either tracking maximum
IOMMU supported address space (e.g. 39/48 address width on Intel)
or range-track current mappings and dirty track the new ones
post starting dirty tracking. This will be done as a separate
series, so add a live migration blocker until that is fixed.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/r/20230307125450.62409-14-joao.m.martins@oracle.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add device dirty page tracking start/stop functionality. This uses the
device DMA logging uAPI to start and stop dirty page tracking by device.
Device dirty page tracking is used only if all devices within a
container support device dirty page tracking.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/20230307125450.62409-11-joao.m.martins@oracle.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This header is now only for native Xen code, not PV backends that may be
used in Xen emulation. Since the toolstack libraries may depend on the
specific version of Xen headers that they pull in (and will set the
__XEN_TOOLS__ macro to enable internal definitions that they depend on),
the rule is that xen_native.h (and thus the toolstack library headers)
must be included *before* any of the headers in include/hw/xen/interface.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
There's no need for this to be in the Xen accel code, and as we want to
use the Xen console support with KVM-emulated Xen we'll want to have a
platform-agnostic version of it. Make it use GString to build up the
path while we're at it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The previous commit introduced redirectable gnttab operations fairly
much like-for-like, with the exception of the extra arguments to the
->open() call which were always NULL/0 anyway.
This *changes* the arguments to the ->unmap() operation to include the
original ref# that was mapped. Under real Xen it isn't necessary; all we
need to do from QEMU is munmap(), then the kernel will release the grant,
and Xen does the tracking/refcounting for the guest.
When we have emulated grant tables though, we need to do all that for
ourselves. So let's have the back ends keep track of what they mapped
and pass it in to the ->unmap() method for us.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Move the existing code using libxengnttab to xen-operations.c and allow
the operations to be redirected so that we can add emulation of grant
table mapping for backend drivers.
In emulation, mapping more than one grant ref to be virtually contiguous
would be fairly difficult. The best way to do it might be to make the
ram_block mappings actually backed by a file (shmem or a deleted file,
perhaps) so that we can have multiple *shared* mappings of it. But that
would be fairly intrusive.
Making the backend drivers cope with page *lists* instead of expecting
the mapping to be contiguous is also non-trivial, since some structures
would actually *cross* page boundaries (e.g. the 32-bit blkif responses
which are 12 bytes).
So for now, we'll support only single-page mappings in emulation. Add a
XEN_GNTTAB_OP_FEATURE_MAP_MULTIPLE flag to indicate that the native Xen
implementation *does* support multi-page maps, and a helper function to
query it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
The existing implementation calling into the real libxenevtchn moves to
a new file hw/xen/xen-operations.c, and is called via a function table
which in a subsequent commit will also be able to invoke the emulated
event channel support.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
nmi.h and notify.h are not needed here, drop them to speed up
the compiling a little bit.
Message-Id: <20230210111438.1114600-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
* Support for the Zicbiom, ZCicboz, and Zicbop extensions.
* OpenSBI has been updated to version 1.2, see
<https://github.com/riscv-software-src/opensbi/releases/tag/v1.2> for
the release notes.
* Support for setting the virtual address width (ie, sv39/sv48/sv57) on
the command line.
* Support for ACPI on RISC-V.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEKzw3R0RoQ7JKlDp6LhMZ81+7GIkFAmQGYGgTHHBhbG1lckBk
YWJiZWx0LmNvbQAKCRAuExnzX7sYidmyEAC6FEMbbFM5D++qR6w6xM6hXgzcrev6
s1kyRRNVa45uSA78ti/Zi0hsDLNf7ZsNPndF0OIkkO5iAE0OVm3LU7tV1TqKcT82
Dd9VXxe93zEmfnuJazHrMa54SXPhhnNdWHtKlZ6vBfZpbxgx0FFs50xkCsrM5LQZ
hYHxQUqPWQTvF2MdDHrxCuLcdKl+Wg3ysCcgRh2d049KUBrIu6vNaHC2+AGRjCbj
BkrGCkB82fTmVJjzAcVWQxLoAV12pCbJS4og1GtP8hA7WevtB39tbPin9siBKRZp
QBeiIsg0nebkpmZGrb+xWVwlIBNe9yYwJa0KmveQk8v7L5RIzjM1mtDL91VrVljC
KC2tfT570m0Iq2NoFMb3wd/kESHFzVDM/g+XYqRd4KSoiCNP/RbqYNQBwbMc31Tr
E27xfA1D8w2vem0Rk20x3KgPf1Z5OmGXjq6YObTpnAzG8cZlA37qKBP+ortt5aHX
GZSg3CAwknHHVajd4aaegkPsHxm1tRvoTfh38MwkPSNxaA9GD0nz0k9xaYDmeZ2L
olfanNsaQEwcVUId31+7sAENg1TZU0fnj879/nxkMUCazVTdL8/mz+IoTTx0QCST
3+9ATWcyJUlmjbDKIs7kr1L+wJdvvHEJggPAbbPI8ekpXaLZvUYOT6ObzYKNAmwY
wELQBn8QKXcLVA==
=5gAt
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230306' of https://gitlab.com/palmer-dabbelt/qemu into staging
Sixth RISC-V PR for 8.0
* Support for the Zicbiom, ZCicboz, and Zicbop extensions.
* OpenSBI has been updated to version 1.2, see
<https://github.com/riscv-software-src/opensbi/releases/tag/v1.2> for
the release notes.
* Support for setting the virtual address width (ie, sv39/sv48/sv57) on
the command line.
* Support for ACPI on RISC-V.
# -----BEGIN PGP SIGNATURE-----
#
# iQJHBAABCAAxFiEEKzw3R0RoQ7JKlDp6LhMZ81+7GIkFAmQGYGgTHHBhbG1lckBk
# YWJiZWx0LmNvbQAKCRAuExnzX7sYidmyEAC6FEMbbFM5D++qR6w6xM6hXgzcrev6
# s1kyRRNVa45uSA78ti/Zi0hsDLNf7ZsNPndF0OIkkO5iAE0OVm3LU7tV1TqKcT82
# Dd9VXxe93zEmfnuJazHrMa54SXPhhnNdWHtKlZ6vBfZpbxgx0FFs50xkCsrM5LQZ
# hYHxQUqPWQTvF2MdDHrxCuLcdKl+Wg3ysCcgRh2d049KUBrIu6vNaHC2+AGRjCbj
# BkrGCkB82fTmVJjzAcVWQxLoAV12pCbJS4og1GtP8hA7WevtB39tbPin9siBKRZp
# QBeiIsg0nebkpmZGrb+xWVwlIBNe9yYwJa0KmveQk8v7L5RIzjM1mtDL91VrVljC
# KC2tfT570m0Iq2NoFMb3wd/kESHFzVDM/g+XYqRd4KSoiCNP/RbqYNQBwbMc31Tr
# E27xfA1D8w2vem0Rk20x3KgPf1Z5OmGXjq6YObTpnAzG8cZlA37qKBP+ortt5aHX
# GZSg3CAwknHHVajd4aaegkPsHxm1tRvoTfh38MwkPSNxaA9GD0nz0k9xaYDmeZ2L
# olfanNsaQEwcVUId31+7sAENg1TZU0fnj879/nxkMUCazVTdL8/mz+IoTTx0QCST
# 3+9ATWcyJUlmjbDKIs7kr1L+wJdvvHEJggPAbbPI8ekpXaLZvUYOT6ObzYKNAmwY
# wELQBn8QKXcLVA==
# =5gAt
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 06 Mar 2023 21:51:36 GMT
# gpg: using RSA key 2B3C3747446843B24A943A7A2E1319F35FBB1889
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmerdabbelt@google.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
# Subkey fingerprint: 2B3C 3747 4468 43B2 4A94 3A7A 2E13 19F3 5FBB 1889
* tag 'pull-riscv-to-apply-20230306' of https://gitlab.com/palmer-dabbelt/qemu: (22 commits)
MAINTAINERS: Add entry for RISC-V ACPI
hw/riscv/virt.c: Initialize the ACPI tables
hw/riscv/virt: virt-acpi-build.c: Add RHCT Table
hw/riscv/virt: virt-acpi-build.c: Add RINTC in MADT
hw/riscv/virt: Enable basic ACPI infrastructure
hw/riscv/virt: Add memmap pointer to RiscVVirtState
hw/riscv/virt: Add a switch to disable ACPI
hw/riscv/virt: Add OEM_ID and OEM_TABLE_ID fields
riscv: Correctly set the device-tree entry 'mmu-type'
riscv: Introduce satp mode hw capabilities
riscv: Allow user to set the satp mode
riscv: Change type of valid_vm_1_10_[32|64] to bool
riscv: Pass Object to register_cpu_props instead of DeviceState
roms/opensbi: Upgrade from v1.1 to v1.2
gitlab/opensbi: Move to docker:stable
hw: intc: Use cpu_by_arch_id to fetch CPU state
target/riscv: cpu: Implement get_arch_id callback
disas/riscv Fix ctzw disassemble
hw/riscv/virt.c: add cbo[mz]-block-size fdt properties
target/riscv: add Zicbop cbo.prefetch{i, r, m} placeholder
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add basic ACPI infrastructure for RISC-V with below tables.
1) DSDT with below basic objects
- CPUs
- fw_cfg
2) FADT revision 6 with HW_REDUCED flag
3) XSDT
4) RSDP
Add this functionality in a new file virt-acpi-build.c and enable
building this infrastructure.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230302091212.999767-5-sunilvl@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
memmap needs to be exported outside of virt.c so that
modules like acpi can use it. Hence, add a pointer field
in RiscVVirtState structure and initialize it with the
memorymap.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230302091212.999767-4-sunilvl@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
ACPI will be enabled by default. Add a switch to turn off
for testing and debug purposes.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230302091212.999767-3-sunilvl@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
ACPI needs OEM_ID and OEM_TABLE_ID for the machine. Add these fields
in the RISCVVirtState structure and initialize with default values.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230302091212.999767-2-sunilvl@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Allwinner h3 has 4 twi(i2c) devices named twi0, twi1, twi2 and r_twi.
The registers are compatible with TYPE_AW_I2C_SUN6I, write 1 to clear
control register's INT_FLAG bit.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fedora 39 will ship its arm64 kernels in the new generic EFI zboot
format, using gzip compression for the payload.
For doing EFI boot in QEMU, this is completely transparent, as the
firmware or bootloader will take care of this. However, for direct
kernel boot without firmware, we will lose the ability to boot such
distro kernels unless we deal with the new format directly.
EFI zboot images contain metadata in the header regarding the placement
of the compressed payload inside the image, and the type of compression
used. This means we can wire up the existing gzip support without too
much hassle, by parsing the header and grabbing the payload from inside
the loaded zboot image.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Message-id: 20230303160109.3626966-1-ardb@kernel.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: tweaked comment formatting, fixed checkpatch nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Atomic operations are read-modify-write, and we'd like to
be able to test both read and write with one call. This is
easy enough, with BP_MEM_READ | BP_MEM_WRITE.
Add BP_HIT_SHIFT to make it easy to set BP_WATCHPOINT_HIT_*.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This queue includes a stub implementation for the dcblc instruction to
avoid an illegal instrunction exception when using u-boot with mpc85xx.
It also includes a PHB fix with user-created pnv-phb devices and
Skiboot.
-----BEGIN PGP SIGNATURE-----
iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZAJllhYcZGFuaWVsaGI0
MTNAZ21haWwuY29tAAoJEDzZypbeAzFk02YA/2YnJl0aRw6hgiayI2rLbcwQcVfp
oGAhh4QmqFL2UJw2AQDra0kh9sxBSEcqhltNnOa08tBnHPts3W/A8nmFtCd4Cw==
=VRNM
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20230303' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2023-03-03:
This queue includes a stub implementation for the dcblc instruction to
avoid an illegal instrunction exception when using u-boot with mpc85xx.
It also includes a PHB fix with user-created pnv-phb devices and
Skiboot.
# -----BEGIN PGP SIGNATURE-----
#
# iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCZAJllhYcZGFuaWVsaGI0
# MTNAZ21haWwuY29tAAoJEDzZypbeAzFk02YA/2YnJl0aRw6hgiayI2rLbcwQcVfp
# oGAhh4QmqFL2UJw2AQDra0kh9sxBSEcqhltNnOa08tBnHPts3W/A8nmFtCd4Cw==
# =VRNM
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 03 Mar 2023 21:24:38 GMT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20230303' of https://gitlab.com/danielhb/qemu:
pnv_phb4_pec: Simplify/align code to parent user-created PHBs
pnv_phb4_pec: Move pnv_phb4_get_pec() to rightful file
pnv_phb4_pec: Only export existing PHBs to the device tree
pnv_phb4_pec: Keep track of instantiated PHBs
target/ppc/translate: Add dummy implementation for dcblc instruction
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When instantiating a user-created PHB on P9/P10, we don't really have
a reason any more to go through an indirection in pnv_chip_add_phb()
in pnv.c, we can go straight to the right function in
pnv_phb4_pec.c. That way, default PHBs and user-created PHBs are all
handled in the same file. This patch also renames pnv_phb4_get_pec()
to pnv_pec_add_phb() to better reflect that it "hooks" a PHB to a PEC.
For P8, the PHBs are parented to the chip directly, so it makes sense
to keep calling pnv_chip_add_phb() in pnv.c, to also be consistent
with where default PHBs are handled. The only change here is that,
since that function is now only used for P8, we can refine the return
type.
So overall, the PnvPHB front-end now has a pnv_phb_user_get_parent()
function which handles the parenting of the user-created PHBs by
calling the right function in the right file based on the processor
version. It's also easily extensible if we ever need to support a
different parent object.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20230302163715.129635-5-fbarrat@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The function pnv_phb4_get_pec() exposes some internals of the PEC and
PHB logic, yet it was in the higher level hw/ppc/pnv.c file for
historical reasons: P8 implements the PHBs from pnv.c directly, but on
P9/P10, it's done through the CEC model, which has its own file. So
move pnv_phb4_get_pec() to hw/pci-host/pnv_phb4_pec.c, where it fits
naturally.
While at it, replace the PnvPHB4 parameter by the PnvPHB front-end,
since it has all the information needed and simplify it a bit.
No functional changes.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20230302163715.129635-4-fbarrat@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add an array on the PEC object to keep track of the PHBs which are
instantiated. The array can be sparsely populated when using
user-created PHBs. It will be useful for the next patch to only export
instantiated PHBs in the device tree.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20230302163715.129635-2-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
* fix for the Aspeed I2C slave mode
* a new I2C echo device from Klaus and its associated test in avocado.
* initial SoC cleanups to allow the use of block devices instead of
drives on the command line.
* new facebook machines and eeprom fixes for the Fuji
* readline fix
-----BEGIN PGP SIGNATURE-----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=ExnJ
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20230302' of https://github.com/legoater/qemu into staging
aspeed queue:
* fix for the Aspeed I2C slave mode
* a new I2C echo device from Klaus and its associated test in avocado.
* initial SoC cleanups to allow the use of block devices instead of
drives on the command line.
* new facebook machines and eeprom fixes for the Fuji
* readline fix
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmQAnrQACgkQUaNDx8/7
# 7KGIvQ//Te2eSxlZNxAXHb3HSVFRaBW+2EkJzNlalX75olFSzCLe8BnAHK5xPlYv
# JjU0aPjWaPohPLdbNbAsJY2B8AwMGbUTjSv+ORRWF6s97LTVD9WcAYHgOTCz6d2X
# ZrArJ5msEQAFEySOLmBqTcuyW3t4w8XeII+B09HZIS8Gn3F9kX5+4JCw9E4sX8fS
# n9ayclMmrXCPbkGA4bfwJp3KI1Tc/WXNRyG0AmPEmepid7ECr5tVvQoXRMF1Sy/D
# 10qbHEcmQXvZDy85M2ED1niOac4oU+EY8Wvjzkgc36uXcjqf0jIUfw56cwGSNVkW
# MhPXSMiH4tEjgxmtzld3LeA6TGfrFcCvRXYiCuYWHjBS3gptlqY6Q0580vxoQVXL
# lTYui57LB1YStNLcLG9toP0d4/fRfeqEx7ddCQKlopnW/K392eoJo0aYoVGVJhIC
# 3QhN525EFUwMm4FDpdSW29Gfbk/ytpf0u4hQ6JPeBl8psirRKqCGuwr5NOnPYTaN
# yErlsq2eL83t9kLo+2YIqgWic85wNP3kqAjIaE6lminqX7sWFH3V1g9HqUQZVG1g
# msatZMiCCvwSFuz3DPkSfnuhqwaHuhvCATZloCtguCmnbUK9qUVVzvodKw62sZrd
# GdS2XvRNyoOwezz0tDEvPipyZ7RpcaatryHNuzGwRsE5Lvr73dg=
# =ExnJ
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 02 Mar 2023 13:03:48 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20230302' of https://github.com/legoater/qemu:
aspeed/smc: Replace SysBus IRQs with GPIO lines
aspeed: Add a boot_rom overlap region in the SoC spi_boot container
aspeed: Introduce a spi_boot region under the SoC
aspeed/fuji : correct the eeprom size
hw/at24c : modify at24c to support 1 byte address mode
hw/arm/aspeed: Adding new machine Tiogapass in QEMU
hw/arm/aspeed: Adding new machine Yosemitev2 in QEMU
tests/avocado/machine_aspeed.py: Add an I2C slave test
hw/misc: add a toy i2c echo device
hw/i2c: only schedule pending master when bus is idle
readline: fix hmp completion issue
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZAFb5wAKCRBAov/yOSY+
35hmA/sHIGXU5zQV6p6DBILFGEE6x91sPtV8WKY3zujVY0hsfD4SF6bKTaKJYisZ
EztZZ5/EunQcu/vfgO46YtYysEWzrzGiinbZ5lAjxk6sdlBYlfcTQLAQEEW3zPbP
qB3SiiGmGQ0iYFHIlkyi1tCF5OEmqqQKrHYrNVk6cGBoJle2PA==
=giPH
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20230303' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20230303
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZAFb5wAKCRBAov/yOSY+
# 35hmA/sHIGXU5zQV6p6DBILFGEE6x91sPtV8WKY3zujVY0hsfD4SF6bKTaKJYisZ
# EztZZ5/EunQcu/vfgO46YtYysEWzrzGiinbZ5lAjxk6sdlBYlfcTQLAQEEW3zPbP
# qB3SiiGmGQ0iYFHIlkyi1tCF5OEmqqQKrHYrNVk6cGBoJle2PA==
# =giPH
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 03 Mar 2023 02:31:03 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20230303' of https://gitlab.com/gaosong/qemu:
hw/loongarch/virt: add system_powerdown hmp command support
target/loongarch: Implement Chip Configuraiton Version Register(0x0000)
docs/system/loongarch: update loongson3.rst and rename it to virt.rst
loongarch: Add smbios command line option.
hw/loongarch/virt: rename PCH_PIC_IRQ_OFFSET with VIRT_GSI_BASE
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vhost-user support without ioeventfd
word replacements in vhost user spec
shpc improvements
cleanups, fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQBO8QPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpMUMH/3/FVp4qaF4CDwCHn7xWFRJpOREIhX/iWfUu
lGkwxnB7Lfyqdg7i4CAfgMf2emWKZchEE2DamfCo5bIX0IgRU3DWcOdR9ePvJ29J
cKwIYpxZcB4RYSoWL5OUakQLCT3JOu4XWaXeVjyHABjQhf3lGpwN4KmIOBGOy/N6
0YHOQScW2eW62wIOwhAEuYQceMt6KU32Uw3tLnMbJliiBf3a/hPctVNM9TFY9pcd
UYHGfBx/zD45owf1lTVEQFDg0eqPZKWW29g5haiOd5oAyXHHolzu+bt3bU7lH46b
f7iP12LqDudyrgoF5YWv3NJ4HaGm5V3kPqNqLLF/mjF7alxG+N8=
=hN3h
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
vhost-user support without ioeventfd
word replacements in vhost user spec
shpc improvements
cleanups, fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQBO8QPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpMUMH/3/FVp4qaF4CDwCHn7xWFRJpOREIhX/iWfUu
# lGkwxnB7Lfyqdg7i4CAfgMf2emWKZchEE2DamfCo5bIX0IgRU3DWcOdR9ePvJ29J
# cKwIYpxZcB4RYSoWL5OUakQLCT3JOu4XWaXeVjyHABjQhf3lGpwN4KmIOBGOy/N6
# 0YHOQScW2eW62wIOwhAEuYQceMt6KU32Uw3tLnMbJliiBf3a/hPctVNM9TFY9pcd
# UYHGfBx/zD45owf1lTVEQFDg0eqPZKWW29g5haiOd5oAyXHHolzu+bt3bU7lH46b
# f7iP12LqDudyrgoF5YWv3NJ4HaGm5V3kPqNqLLF/mjF7alxG+N8=
# =hN3h
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 03 Mar 2023 00:13:56 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (53 commits)
tests/data/acpi/virt: drop (most) duplicate files.
hw/cxl/mailbox: Use new UUID network order define for cel_uuid
qemu/uuid: Add UUID static initializer
qemu/bswap: Add const_le64()
tests: acpi: Update q35/DSDT.cxl for removed duplicate UID
hw/i386/acpi: Drop duplicate _UID entry for CXL root bridge
tests/acpi: Allow update of q35/DSDT.cxl
hw/cxl: Add CXL_CAPACITY_MULTIPLIER definition
hw/cxl: set cxl-type3 device type to PCI_CLASS_MEMORY_CXL
hw/pci-bridge/cxl_downstream: Fix type naming mismatch
hw/mem/cxl_type3: Improve error handling in realize()
MAINTAINERS: Add Fan Ni as Compute eXpress Link QEMU reviewer
intel-iommu: send UNMAP notifications for domain or global inv desc
smmu: switch to use memory_region_unmap_iommu_notifier_range()
memory: introduce memory_region_unmap_iommu_notifier_range()
intel-iommu: fail DEVIOTLB_UNMAP without dt mode
intel-iommu: fail MAP notifier without caching mode
memory: Optimize replay of guest mapping
chardev/char-socket: set s->listener = NULL in char_socket_finalize
hw/pci: Trace IRQ routing on PCI topology
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Experimantal support for writable misa.
* Support for Svadu extension.
* Support for the Zicond extension.
* Fixes to gdbstub, CSR accesses, dependencies between the various
floating-point exceptions, and XTheadMemPair.
* Many cleanups.
-----BEGIN PGP SIGNATURE-----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=FMkl
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230303' of https://gitlab.com/palmer-dabbelt/qemu into staging
Fifth RISC-V PR for QEMU 8.0
* Experimantal support for writable misa.
* Support for Svadu extension.
* Support for the Zicond extension.
* Fixes to gdbstub, CSR accesses, dependencies between the various
floating-point exceptions, and XTheadMemPair.
* Many cleanups.
# -----BEGIN PGP SIGNATURE-----
#
# iQJHBAABCAAxFiEEKzw3R0RoQ7JKlDp6LhMZ81+7GIkFAmQBrrUTHHBhbG1lckBk
# YWJiZWx0LmNvbQAKCRAuExnzX7sYicHrD/9dHBDOYNwyT/C2Q31NHMcEsVN6J0kW
# 0sVyDb2/TUFoXmClMwS6jZYQQwWD7tjjB7BDcvPJ0QKLblDoZFX5JyxpQypIKWcs
# It/E6mk7aG0epH1GoB/mbHFDbeCm4tbo7Vf6cQGpV/vGWBUaOS67c5nenUK7Tlqw
# NTr9qak+9NYVswvMHZ0lUKtO12W1g/1EVkict2/90P2snWbPZ+foWomifGNljmhy
# 5WtCNp27uBKF/uuD9xubLOxSEcqtZFTuKJy7U3azV4I0IKfd6Is83Kd0IwBOrTgT
# MYkFdtQE1jgbkXYVZjft6ymLuqJrcLFYwD8C2zdNAXJLk1Y+MCtGafgW6f6SkT6B
# FrNaSOqQ9xXiaNStF2FwYdmZ476zcY+eEg2rH1grTwCMewZ9r7m3+H8iat/tR0pt
# 9scYAre1oaL33LB6DGZi3JkssNYyj42sutcNao2hQXRHcsh+vv1dLR+Di2mO6Ji5
# MNfvEgCrWWZjNVSwvhwCXdJPqqpyTbkRf8HJEp0gWvjk6VoF8sWidDw/8oMLj+wW
# qZur7GNe+piJNvly85aFSL9J3SX7RyNeDzX/yK3b4k+g6I/ZziQaNgQtB9gYcm6w
# mj3snCwRbEMEhdhPH0+Chm0Wb97knHJS14Vq9wCe2xh16o3HM5FspboLFkGZMjDV
# tRDPFb7pitwdlA==
# =FMkl
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 03 Mar 2023 08:24:21 GMT
# gpg: using RSA key 2B3C3747446843B24A943A7A2E1319F35FBB1889
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmerdabbelt@google.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
# Subkey fingerprint: 2B3C 3747 4468 43B2 4A94 3A7A 2E13 19F3 5FBB 1889
* tag 'pull-riscv-to-apply-20230303' of https://gitlab.com/palmer-dabbelt/qemu: (59 commits)
target/riscv/vector_helper.c: avoid env_archcpu() when reading RISCVCPUConfig
target/riscv/vector_helper.c: create vext_set_tail_elems_1s()
target/riscv/csr.c: avoid env_archcpu() usages when reading RISCVCPUConfig
target/riscv/csr.c: use riscv_cpu_cfg() to avoid env_cpu() pointers
target/riscv/csr.c: simplify mctr()
target/riscv/csr.c: use env_archcpu() in ctr()
target/riscv: Export Svadu property
target/riscv: Add *envcfg.HADE related check in address translation
target/riscv: Add *envcfg.PBMTE related check in address translation
target/riscv: Add csr support for svadu
target/riscv: Fix the relationship of PBMTE/STCE fields between menvcfg and henvcfg
target/riscv: Fix the relationship between menvcfg.PBMTE/STCE and Svpbmt/Sstc extensions
hw/riscv: Move the dtb load bits outside of create_fdt()
hw/riscv: Skip re-generating DT nodes for a given DTB
target/riscv: Add support for Zicond extension
RISC-V: XTheadMemPair: Remove register restrictions for store-pair
target/riscv: Fix checking of whether instruciton at 'pc_next' spans pages
target/riscv: Group all predicate() routines together
target/riscv: Drop priv level check in mseccfg predicate()
target/riscv: Allow debugger to access sstc CSRs
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For loongarch virt machine, add powerdown notification callback
and send ACPI_POWER_DOWN_STATUS event by acpi ged. Also add
acpi dsdt table for ACPI_POWER_BUTTON_DEVICE device in this
patch.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230303010548.295580-1-gaosong@loongson.cn>
In theory gsi base can start from 0 on loongarch virt machine,
however gsi base is hard-coded in linux kernel loongarch system,
else system fails to boot.
This patch renames macro PCH_PIC_IRQ_OFFSET with VIRT_GSI_BASE,
keeps value unchanged. GSI base is common concept in acpi spec
and easy to understand.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20221228030719.991878-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
The cel_uuid was programatically generated previously because there was
no static initializer for network order UUIDs.
Use the new network order initializer for cel_uuid. Adjust
cxl_initialize_mailbox() because it can't fail now.
Update specification reference.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Tested-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230206172816.8201-11-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The default boot address of the Aspeed SoCs is 0x0. For this reason,
the FMC flash device contents are remapped by HW on the first 256MB of
the address space. In QEMU, this is currently done in the machine init
with the setup of a region alias.
Move this code to the SoC and introduce an extra container to prepare
ground for the boot ROM region which will overlap the FMC flash
remapping.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is not given that the current master will release the bus after a
transfer ends. Only schedule a pending master if the bus is idle.
Fixes: 37fa5ca426 ("hw/i2c: support multiple masters")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20221116084312.35808-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The structure type is unused. Also, it's the only user of corresponding
macros, so drop them too.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Kuchin <antonkuchin@yandex-team.ru>
Message-Id: <20230216180356.156832-10-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We already have indicator values in
include/standard-headers/linux/pci_regs.h , no reason to reinvent them
in include/hw/pci/pcie_regs.h. (and we already have usage of
PCI_EXP_SLTCTL_PWR_IND_BLINK and PCI_EXP_SLTCTL_PWR_IND_OFF in
hw/pci/pcie.c, so let's be consistent)
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Kuchin <antonkuchin@yandex-team.ru>
Message-Id: <20230216180356.156832-9-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_dev_cleanup(), called from vu_gpio_disconnect(), clears vhost_dev
so vhost-user-gpio must set the members of vhost_dev each time
connecting.
do_vhost_user_cleanup() should also acquire the pointer to vqs directly
from VHostUserGPIO instead of referring to vhost_dev as it can be called
after vhost_dev_cleanup().
Fixes: 27ba7b027f ("hw/virtio: add boilerplate for vhost-user-gpio device")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20230130140320.77999-1-akihiko.odaki@daynix.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Philippe Mathieu-Daudé