When a SCSI command is received from the guest, the CDB length implied
by the first byte might exceed the number of bytes the guest sent. In
this case scsi_req_new() will read uninitialized data, causing
unpredictable behavior.
Adds the buf_len parameter to scsi_req_new() and plumbs it through the
call stack.
Signed-off-by: John Millikin <john@john-millikin.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1127
Message-Id: <20220817053458.698416-1-john@john-millikin.com>
[Fill in correct length for adapters other than ESP. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make ppc-uic a subclass of ppc4xx-dcr-device which will handle the cpu
link and make it uniform with the other PPC4xx devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <eb548130cf60aea8a6ea4dba4dee1686b3cabc3d.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This device is shared between different 4xx socs.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <63d9b14c8ff5f73e35bffca1036394b5235735ee.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The EBC is shared between 405 and 440 so move it to shared file.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <10eae70509ca4bd74858fc2c0a0f0e4eb9330199.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This device is shared between different 4xx socs.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <5b13ebfd12a71a28035bed5a915cbeee81cf21d1.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The PLB is shared between 405 and 440 so move it to the shared file.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <2498384bf3e18959ee8cb984d72fb66b8a6ecadc.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The Memory Access Layer (MAL) controller is currently modeled as a DCR
device with 4 IRQs. Also drop the ppc4xx_mal_init() helper and adapt
the sam460ex machine.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[balaton: ppc4xx_dcr_register changes, add finalize method]
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <d54a243dff94d95ba30dbcc09c27700a90ade932.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The Device Control Registers (DCR) of on-SoC devices are accessed by
software through the use of the mtdcr and mfdcr instructions. These
are converted in transactions on a side band bus, the DCR bus, which
connects the on-SoC devices to the CPU.
Ideally, we should model these accesses with a DCR namespace and DCR
memory regions but today the DCR handlers are installed in a DCR table
under the CPU. Instead, introduce a little device model wrapper to hold
a CPU link and handle registration of DCR handlers.
The DCR device inherits from SysBus because most of these devices also
have MMIO regions and/or IRQs. Being a SysBusDevice makes things easier
to install the device model in the overall SoC.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[balaton: Explicit opaque parameter for dcr callbacks]
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <9b21bdf55e0a728f093bad299e030d98f302ded0.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Drop the use of ppc4xx_init() and duplicate a bit of code related to
clocks in the SoC realize routine. We will clean that up in the
following patches.
ppc_dcr_init() simply allocates default DCR handlers for the CPU. Maybe
this could be done in model initializer of the CPU families needing it.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20220809153904.485018-8-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
When enabling user created PHBs (a change reverted by commit 9c10d86fee)
we were handling PHBs created by default versus by the user in different
manners. The only difference between these PHBs is that one will have a
valid phb3->chip that is assigned during pnv_chip_power8_realize(),
while the user created needs to search which chip it belongs to.
Aside from that there shouldn't be any difference. Making the default
PHBs behave in line with the user created ones will make it easier to
re-introduce them later on. It will also make the code easier to follow
since we are dealing with them in equal manner.
The first step is to turn chip8->phbs[] into a PnvPHB3 pointer array.
This will allow us to assign user created PHBs into it later on. The way
we initilize the default case is now more in line with that would happen
with the user created case: the object is created, parented by the chip
because pnv_xscom_dt() relies on it, and then assigned to the array.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220811163950.578927-6-danielhb413@gmail.com>
pnv_parent_qom_fixup() and pnv_parent_bus_fixup() are versions of the
helpers that were reverted by commit 9c10d86fee "ppc/pnv: Remove
user-created PHB{3,4,5} devices". They are needed to amend the QOM and
bus hierarchies of user created pnv-phbs, matching them with default
pnv-phbs.
A new helper pnv_phb_user_device_init() is created to handle
user-created devices setup. We're going to call it inside
pnv_phb_realize() in case we're realizing an user created device. This
will centralize all user device realated in a single spot, leaving the
realize functions of the phb3/phb4 backends untouched.
Another helper called pnv_chip_add_phb() was added to handle the
particularities of each chip version when adding a new PHB.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220811163950.578927-5-danielhb413@gmail.com>
The same rationale provided in the PHB3 bus case applies here.
Note: we could have merged both buses in a single object, like we did
with the root ports, and spare some boilerplate. The reason we opted to
preserve both buses objects is twofold:
- there's not user side advantage in doing so. Unifying the root ports
presents a clear user QOL change when we enable user created devices back.
The buses objects, aside from having a different QOM name, is transparent
to the user;
- we leave a door opened in case we want to increase the root port limit
for phb4/5 later on without having to deal with phb3 code.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220811163950.578927-3-danielhb413@gmail.com>
We rely on the phb-id and chip-id, which are PHB properties, to assign
chassis and slot to the root port. For default devices this is no big
deal: the root port is being created under pnv_phb_realize() and the
values are being passed on via the 'index' and 'chip-id' of the
pnv_phb_attach_root_port() helper.
If we want to implement user created root ports we have a problem. The
user created root port will not be aware of which PHB it belongs to,
unless we're willing to violate QOM best practices and access the PHB
via dev->parent_bus->parent. What we can do is to access the root bus
parent bus.
Since we're already assigning the root port as QOM child of the bus, and
the bus is initiated using PHB properties, let's add phb-id and chip-id
as properties of the bus. This will allow us trivial access to them, for
both user-created and default root ports, without doing anything too
shady with QOM.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220811163950.578927-2-danielhb413@gmail.com>
The helper is only used in this file.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-13-danielhb413@gmail.com>
The attribute is unused.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-11-danielhb413@gmail.com>
We support only a single root port, PNV_PHB_ROOT_PORT.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-10-danielhb413@gmail.com>
The unified pnv-phb-root-port can be used instead. The phb4-root-port
device isn't exposed to the user in any official QEMU release so there's
no ABI breakage in removing it.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-9-danielhb413@gmail.com>
The unified pnv-phb-root-port can be used in its place. There is no ABI
breakage in doing so because no official QEMU release introduced user
creatable pnv-phb3-root-port devices.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-8-danielhb413@gmail.com>
Change the parent type of the PnvPHB4 device to TYPE_PARENT since the
PCI bus is going to be initialized by the PnvPHB parent. Functions that
needs to access the bus via a PnvPHB4 object can do so via the
phb4->phb_base pointer.
pnv_phb4_pec now creates a PnvPHB object.
The powernv9 machine class will create PnvPHB devices with version '4'.
powernv10 will create using version '5'. Both are using global machine
properties in their class_init() to do that.
These changes will benefit us when adding PnvPHB user creatable devices
for powernv9 and powernv10.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-6-danielhb413@gmail.com>
Similar to what we already did for the PnvPHB3 device, let's add a
helper to init the bus when using a PnvPHB4. This helper will be used by
PnvPHb when PnvPHB4 turns into a backend.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-5-danielhb413@gmail.com>
We need a handful of changes that needs to be done in a single swoop to
turn PnvPHB3 into a PnvPHB backend.
In the PnvPHB3, since the PnvPHB device implements PCIExpressHost and
will hold the PCI bus, change PnvPHB3 parent to TYPE_DEVICE. There are a
couple of instances in pnv_phb3.c that needs to access the PCI bus, so a
phb_base pointer is added to allow access to the parent PnvPHB. The
PnvPHB3 root port will now be connected to a PnvPHB object.
In pnv.c, the powernv8 machine chip8 will now hold an array of PnvPHB
objects. pnv_get_phb3_child() needs to be adapted to return the PnvPHB3
backend from the PnvPHB child. A global property is added in
pnv_machine_power8_class_init() to ensure that all PnvPHBs are created
with phb->version = 3.
After all these changes we're still able to boot a powernv8 machine with
default settings. The real gain will come with user created PnvPHB
devices, coming up next.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-4-danielhb413@gmail.com>
The PnvPHB3 bus init consists of initializing the pci_io and pci_mmio
regions, registering it via pci_register_root_bus() and then setup the
iommu.
We'll want to init the bus from outside pnv_phb3.c when the bus is
removed from the PnvPHB3 device and put into a new parent PnvPHB device.
The new pnv_phb3_bus_init() helper will be used by the parent to init
the bus when using the PHB3 backend.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220624084921.399219-2-danielhb413@gmail.com>
The SBE (Self Boot Engine) are on-chip microcontrollers that perform
early boot steps, as well as provide some runtime facilities (e.g.,
timer, secure register access, MPIPL). The latter facilities are
accessed mostly via a message system called SBEFIFO.
This driver provides initial emulation for the SBE runtime registers
and a very basic SBEFIFO implementation that provides the timer
command. This covers the basic SBE behaviour expected by skiboot when
booting.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20220811093726.1442343-1-npiggin@gmail.com>
[danielhb: fixed SBE_HOST_RESPONSE_MASK long line]
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220707163720.1421716-5-berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Change macro name 'LS7A_XXX' to 'VIRT_XXX', as the loongarch
virt machinue use the GPEX bridge instead of LS7A bridge. So
the macro name should keep consistency.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220729073018.27037-3-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The added enforcing is only relevant in the case of AMD where the
range right before the 1TB is restricted and cannot be DMA mapped
by the kernel consequently leading to IOMMU INVALID_DEVICE_REQUEST
or possibly other kinds of IOMMU events in the AMD IOMMU.
Although, there's a case where it may make sense to disable the
IOVA relocation/validation when migrating from a
non-amd-1tb-aware qemu to one that supports it.
Relocating RAM regions to after the 1Tb hole has consequences for
guest ABI because we are changing the memory mapping, so make
sure that only new machine enforce but not older ones.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220719170014.27028-12-joao.m.martins@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the pre-initialized pci-host qdev and fetch the
pci-hole64-size into pc_memory_init() newly added argument.
Use PCI_HOST_PROP_PCI_HOLE64_SIZE pci-host property for
fetching pci-hole64-size.
This is in preparation to determine that host-phys-bits are
enough and for pci-hole64-size to be considered to relocate
ram-above-4g to be at 1T (on AMD platforms).
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220719170014.27028-4-joao.m.martins@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At the start of pc_memory_init() we usually pass a range of
0..UINT64_MAX as pci_memory, when really its 2G (i440fx) or
32G (q35). To get the real user value, we need to get pci-host
passed property for default pci_hole64_size. Thus to get that,
create the qdev prior to memory init to better make estimations
on max used/phys addr.
This is in preparation to determine that host-phys-bits are
enough and also for pci-hole64-size to be considered to relocate
ram-above-4g to be at 1T (on AMD platforms).
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220719170014.27028-3-joao.m.martins@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rather than hardcoding the 4G boundary everywhere, introduce a
X86MachineState field @above_4g_mem_start and use it
accordingly.
This is in preparation for relocating ram-above-4g to be
dynamically start at 1T on AMD platforms.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220719170014.27028-2-joao.m.martins@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst the interleave granularity is always small enough that this isn't
a real problem (much less than 4GiB) let's change the constant
to ULL to fix the coverity warning.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: 829de299d1 ("hw/cxl/component: Add utils for interleave parameter encoding/decoding")
Fixes: Coverity CID 1488868
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220701132300.2264-4-Jonathan.Cameron@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This got left behind in the move of the CXL setup code from core
files to the machines that support it.
Link: 1ebf9001fb
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220701132300.2264-2-Jonathan.Cameron@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Reviewed-by: Jingqi Liu <jingqi.liu@intel.com>
Message-Id: <20220704085852.330005-1-robert.hu@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tiny machines optimized for fast boot time generally don't use EFI,
which means a random seed has to be supplied some other way. For this
purpose, Linux (≥5.20) supports passing a seed in the setup_data table
with SETUP_RNG_SEED, specially intended for hypervisors, kexec, and
specialized bootloaders. The linked commit shows the upstream kernel
implementation.
At Paolo's request, we don't pass these to versioned machine types ≤7.0.
Link: https://git.kernel.org/tip/tip/c/68b8e9713c8
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220721125636.446842-1-Jason@zx2c4.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This replaces yesterdays pull and:
a) Fixes some test build errors without TLS
b) Reenabled the zlib acceleration on s390
now that we have Ilya's fix
Hyman's dirty page rate limit set
Ilya's fix for zlib vs migration
Peter's postcopy-preempt
Cleanup from Dan
zero-copy tidy ups from Leo
multifd doc fix from Juan
Revert disable of zlib acceleration on s390x
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=wiSA
-----END PGP SIGNATURE-----
Merge tag 'pull-migration-20220720c' of https://gitlab.com/dagrh/qemu into staging
Migration pull 2022-07-20
This replaces yesterdays pull and:
a) Fixes some test build errors without TLS
b) Reenabled the zlib acceleration on s390
now that we have Ilya's fix
Hyman's dirty page rate limit set
Ilya's fix for zlib vs migration
Peter's postcopy-preempt
Cleanup from Dan
zero-copy tidy ups from Leo
multifd doc fix from Juan
Revert disable of zlib acceleration on s390x
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Wed 20 Jul 2022 12:18:56 BST
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* tag 'pull-migration-20220720c' of https://gitlab.com/dagrh/qemu: (30 commits)
Revert "gitlab: disable accelerated zlib for s390x"
migration: Avoid false-positive on non-supported scenarios for zero-copy-send
multifd: Document the locking of MultiFD{Send/Recv}Params
migration/multifd: Report to user when zerocopy not working
Add dirty-sync-missed-zero-copy migration stat
QIOChannelSocket: Fix zero-copy flush returning code 1 when nothing sent
migration: remove unreachable code after reading data
tests: Add postcopy preempt tests
tests: Add postcopy tls recovery migration test
tests: Add postcopy tls migration test
tests: Move MigrateCommon upper
migration: Respect postcopy request order in preemption mode
migration: Enable TLS for preempt channel
migration: Export tls-[creds|hostname|authz] params to cmdline too
migration: Add helpers to detect TLS capability
migration: Add property x-postcopy-preempt-break-huge
migration: Create the postcopy preempt channel asynchronously
migration: Postcopy recover with preempt enabled
migration: Postcopy preemption enablement
migration: Postcopy preemption preparation on channel creation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1
iQEcBAABAgAGBQJi18PHAAoJEO8Ells5jWIRCEQH+wepXDoT6Q56xmUgxVs+hlAD
CXGy71/cNV08Yu3PTTXo8SYaw+KXxsA9ECgIr2hsfPXarAdoOpJFpZR0HoqIzaXd
kpD6bvwN8bEEOlAHxKcb6/VM+VYntZBfkH9m1WLGx3fHILazLblyL8w2Hkp7NK9J
IBpQQ63uU8Xt0+js96Z/sPOKRjrtbKXFT1bhY2CI8MKZpuqNyED0jZYwbNdnRwZN
fuKbpsaaT4Wxx+mQMg7H7a0e/xx3DNi2F6cAtGLH98WYzbLFgExSSK8G8jnwEVfM
EKWfU7N4zmokq7jN99yvGzjIzLrnLX6yn/ifSs+lQOzdtCA9zEbotI+CDCVdPs4=
=9zus
-----END PGP SIGNATURE-----
Merge tag 'net-pull-request' of https://github.com/jasowang/qemu into staging
# gpg: Signature made Wed 20 Jul 2022 09:58:47 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* tag 'net-pull-request' of https://github.com/jasowang/qemu: (25 commits)
net/colo.c: fix segmentation fault when packet is not parsed correctly
net/colo.c: No need to track conn_list for filter-rewriter
net/colo: Fix a "double free" crash to clear the conn_list
softmmu/runstate.c: add RunStateTransition support form COLO to PRELAUNCH
vdpa: Add x-svq to NetdevVhostVDPAOptions
vdpa: Add device migration blocker
vdpa: Extract get features part from vhost_vdpa_get_max_queue_pairs
vdpa: Buffer CVQ support on shadow virtqueue
vdpa: manual forward CVQ buffers
vhost-net-vdpa: add stubs for when no virtio-net device is present
vdpa: Export vhost_vdpa_dma_map and unmap calls
vhost: Add svq avail_handler callback
vhost: add vhost_svq_poll
vhost: Expose vhost_svq_add
vhost: add vhost_svq_push_elem
vhost: Track number of descs in SVQDescState
vhost: Add SVQDescState
vhost: Decouple vhost_svq_add from VirtQueueElement
vhost: Check for queue full at vhost_svq_add
vhost: Move vhost_svq_kick call to vhost_svq_add
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Setup a negative feedback system when vCPU thread
handling KVM_EXIT_DIRTY_RING_FULL exit by introducing
throttle_us_per_full field in struct CPUState. Sleep
throttle_us_per_full microseconds to throttle vCPU
if dirtylimit is in service.
Signed-off-by: Hyman Huang(黄勇) <huangy81@chinatelecom.cn>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <977e808e03a1cef5151cae75984658b6821be618.1656177590.git.huangy81@chinatelecom.cn>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Since the vhost-vdpa device is exposing _F_LOG, adding a migration blocker if
it uses CVQ.
However, qemu is able to migrate simple devices with no CVQ as long as
they use SVQ. To allow it, add a placeholder error to vhost_vdpa, and
only add to vhost_dev when used. vhost_dev machinery place the migration
blocker if needed.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Do a simple forwarding of CVQ buffers, the same work SVQ could do but
through callbacks. No functional change intended.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Shadow CVQ will copy buffers on qemu VA, so we avoid TOCTOU attacks from
the guest that could set a different state in qemu device model and vdpa
device.
To do so, it needs to be able to map these new buffers to the device.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This allows external vhost-net devices to modify the state of the
VirtIO device model once the vhost-vdpa device has acknowledged the
control commands.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
vhost-vdpa control virtqueue needs to know the maximum entries supported
by the virtio-net device, so we know if it is possible to apply the
filter.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add LoongArch flatted device tree, adding cpu device node, firmware cfg node,
pcie node into it, and create fdt rom memory region. Now fdt info is not
full since only uefi bios uses fdt, linux kernel does not use fdt.
Loongarch Linux kernel uses acpi table which is full in qemu virt
machine.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-7-yangxiaojuan@loongson.cn>
[rth: Set TARGET_NEED_FDT, add fdt to meson.build]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Loongarch virt machine uses general hardware reduces acpi method, rather
than LS7A acpi device. Now only power management function is used in
acpi ged device, memory hotplug will be added later. Also acpi tables
such as RSDP/RSDT/FADT etc.
The acpi table has submited to acpi spec, and will release soon.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-6-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add smbios support for loongarch virt machine, and put them into fw_cfg
table so that bios can parse them quickly. The weblink of smbios spec:
https://www.dmtf.org/dsp/DSP0134, the version is 3.6.0.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-5-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add uefi bios loading support, now only uefi bios is porting to
loongarch virt machine.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-3-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add fw_cfg table for loongarch virt machine, including memmap table.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220712083206.4187715-2-yangxiaojuan@loongson.cn>
[rth: Replace fprintf with assert; drop unused return value;
initialize reserved slot to zero.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This legacy function is only used during the initialisation of the MIPS magnum
machine, so inline its functionality directly into mips_jazz_init() and then
remove it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-41-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that the legacy ps2_mouse_init() function is no longer used, it can be completely
removed along with its associated trace-event.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-40-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 mouse device within KBDState using
object_initialize_child() in i8042_initfn() and i8042_mmio_init() and realize
it in i8042_realizefn() and i8042_mmio_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-39-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that the legacy ps2_kbd_init() function is no longer used, it can be completely
removed along with its associated trace-event.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-38-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 keyboard device within KBDState using
object_initialize_child() in i8042_initfn() and i8042_mmio_init() and realize
it in i8042_realizefn() and i8042_mmio_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-37-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 mouse device within LASIPS2MousePort using
object_initialize_child() in lasips2_mouse_port_init() and realize it in
lasips2_mouse_port_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-34-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 keyboard device within LASIPS2KbdPort using
object_initialize_child() in lasips2_kbd_port_init() and realize it in
lasips2_kbd_port_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-33-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This makes it clearer that the pointer is a reference to the LASIPS2 container
device rather than an implied part of the QOM hierarchy.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-30-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now we can implement port-based IRQs by wiring the PS2 device IRQs to the
LASI2Port named input gpios rather than directly to the LASIPS2 device, and
generate the LASIPS2 output IRQ from the int_status bitmap representing the
individual port IRQs instead of the birq boolean.
This enables us to remove the separate PS2 keyboard and PS2 mouse named input
gpios from the LASIPS2 device and simplify the register implementation to
drive the port IRQ using qemu_set_irq() rather than accessing the LASIPS2
device IRQs directly. As a consequence the IRQ level logic in lasips2_set_irq()
can also be simplified accordingly.
For now this patch ignores adding the int_status bitmap and simply drops the
birq boolean from the vmstate_lasips2 VMStateDescription. This is because the
migration stream is already missing some required LASIPS2 fields, and as this
series already introduces a migration break for the lasips2 device it is
easiest to fix this in a follow-up patch.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220712215251.7944-29-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The LASIPS2 device named input gpio is soon to be connected to the port output
IRQs. Add a new int_status field to LASIPS2State which is a bitmap representing
the port input IRQ status which will be enabled in the next patch.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220712215251.7944-28-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The named input gpio is to be connected to the IRQ output of the downstream
PS2 device and used to drive the port IRQ. Initialise the named input gpio
in lasips2_port_init() and add new lasips2_port_class_init() and
lasips2_port_realize() functions to connect the PS2 device output gpio to
the new named input gpio.
Note that the reference to lasips2_port_realize() is stored in
LASIPS2PortDeviceClass but not yet used.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-27-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will soon be used to store the reference to the LASIPS2_PORT parent device
for LASIPS2_KBD_PORT and LASIPS2_MOUSE_PORT.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-26-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Introduce a new lasips2_port_init() QOM init function for the LASIPS2_PORT type
and use it to initialise a new gpio for use as a port IRQ. Add a new qemu_irq
representing the gpio as a new irq field within LASIPS2Port.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-25-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The existing boolean irq field in LASIPS2Port will soon be replaced by a proper
qemu_irq, so rename the field to birq to allow the upcoming qemu_irq to use the
irq name.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-24-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move the initialisation of the mouse port from lasips2_init() to
a new lasips2_mouse_port_init() function which will be invoked using
object_initialize_child() during the LASIPS2 device init.
Update LASIPS2State so that it now holds the new LASIPS2MousePort child object and
ensure that it is realised in lasips2_realize().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-21-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move the initialisation of the keyboard port from lasips2_init() to
a new lasips2_kbd_port_init() function which will be invoked using
object_initialize_child() during the LASIPS2 device init.
Update LASIPS2State so that it now holds the new LASIPS2KbdPort child object and
ensure that it is realised in lasips2_realize().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-20-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_MOUSE_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-19-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_KBD_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-18-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This becomes an abstract QOM type which will be a parent type for separate
keyboard and mouse port types.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-17-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This allows the compiler to enforce that the PS2 device pointer is always of
type PS2State. Update the name of the pointer from dev to ps2dev to emphasise
this type change.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-16-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is only one user of the legacy lasips2_initfn() function which is in
machine_hppa_init(), so inline its functionality into machine_hppa_init() and
then remove it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-15-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base property was only needed for use by vmstate_register() in order to
preserve migration compatibility. Now that the lasips2 migration state is
registered through the DeviceClass vmsd field, the base property and also
the lasips2_properties array can be removed completely as they are no longer
required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-14-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 mouse device within PL050MouseState using
object_initialize_child() in pl050_mouse_init() and realize it in
pl050_mouse_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-12-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instantiate the PS2 keyboard device within PL050KbdState using
object_initialize_child() in pl050_kbd_init() and realize it in
pl050_kbd_realize() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-11-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will soon be used to store the reference to the PL050 parent device
for PL050_KBD_DEVICE and PL050_MOUSE_DEVICE.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-8-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_MOUSE_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-6-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be soon be used to hold the underlying PS2_KBD_DEVICE object.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-5-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This allows the compiler to enforce that the PS2 device pointer is always of
type PS2State. Update the name of the pointer from dev to ps2dev to emphasise
this type change.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-4-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This allows the QOM types in pl050.c to be used elsewhere by simply including
pl050.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220712215251.7944-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is nothing in the specs on DMA engine interrupt lines: it should have
been in the "BCM2835 ARM Peripherals" datasheet but the appropriate
"ARM peripherals interrupt table" (p.113) is nearly empty.
All Raspberry Pi models 1-3 (based on bcm2835) have
Linux device tree (arch/arm/boot/dts/bcm2835-common.dtsi +25):
/* dma channel 11-14 share one irq */
This information is repeated in the driver code
(drivers/dma/bcm2835-dma.c +1344):
/*
* in case of channel >= 11
* use the 11th interrupt and that is shared
*/
In this patch channels 0--10 and 11--14 are handled separately.
Signed-off-by: Andrey Makarov <andrey.makarov@auriga.com>
Message-id: 20220716113210.349153-1-andrey.makarov@auriga.com
[PMM: fixed checkpatch nits]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New ISL69259 device model
* New fby35 multi-SoC machine (AST1030 BIC + AST2600 BMC)
* Aspeed GPIO fixes
* Extension of m25p80 with write protect bits
* More avocado tests using the Aspeed SDK
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmLQJ/kACgkQUaNDx8/7
7KFO5BAAkqiSSQ9G3ihI51ET3+inihrw9wmN7FX5eMOxj8csLz1UbKOJ/YtjXvgt
whfY5/iugVveUW+/X1xZmHbydec24f/umSpqqCtkPkIwCgvN4gjQAriXTK4qqx7g
pCZoWxYeHsR19r985y//I+wFPB//Dd3Ac/1BgA4m0tdy/bK3MPLV2ocDe8d09Yfe
wDYAFby4q8raKzMkJMibP7/phIg4hyguNAYtkSUsJChnXjK8/2ymsjlx7Xz+N1Gp
Fynv9vaFiYOEvmDTPqbs7XMs3Qc+Sjz2RsxgaEdSI4pLk8H8hhgVueYE1ctWlpkI
7q/g5KjXZsq6eKxNYDqU+ysY+vjdLZmO1tEmolgR+k4C+ladUYSBaI1XiGJjCmpb
6vkM2ls1sgmb6C24e8vP64Jp/AgT6Qg7OW1Db3VcpBbQirf9SqtkXezgseOrsnXm
Ni1uQF9NwUiRUWTA/bK4y/pSYNItoQ4KkeoAWPsiEm0d4Pezk2X+EMjJcCTQw9Zx
BFtDxi/3rWB3imvhizynT93+rtNH7Z74kiI7iZGbZr6L2XhpEUlwoo+EOaeb4XAS
ZEuR+kBNUMR9k4YhyF0DlvN61SuD703SdXCROsUq3EzCgza24JM4bl2IMSyv9Wdj
DCL6yYEyf8FsJ9+KtK8A1uXc2yDcV4iGfEqOReTB5+k99ICzgEg=
=faie
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20220714' of https://github.com/legoater/qemu into staging
aspeed queue:
* New ISL69259 device model
* New fby35 multi-SoC machine (AST1030 BIC + AST2600 BMC)
* Aspeed GPIO fixes
* Extension of m25p80 with write protect bits
* More avocado tests using the Aspeed SDK
# gpg: Signature made Thu 14 Jul 2022 15:28:09 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20220714' of https://github.com/legoater/qemu:
aspeed: Add fby35-bmc slot GPIO's
hw/gpio/aspeed: Don't let guests modify input pins
qtest/aspeed_gpio: Add input pin modification test
hw: m25p80: add tests for BP and TB bit write protect
hw: m25p80: Add Block Protect and Top Bottom bits for write protect
test/avocado/machine_aspeed.py: Add SDK tests
docs: aspeed: Minor updates
docs: aspeed: Add fby35 multi-SoC machine section
aspeed: Add AST1030 (BIC) to fby35
aspeed: fby35: Add a bootrom for the BMC
aspeed: Add AST2600 (BMC) to fby35
aspeed: Add fby35 skeleton
aspeed: Make aspeed_board_init_flashes public
aspeed: Refactor UART init for multi-SoC machines
aspeed: Create SRAM name from first CPU index
hw/sensor: Add Renesas ISL69259 device model
hw/sensor: Add IC_DEVICE_ID to ISL voltage regulators
hw/i2c/pmbus: Add idle state to return 0xff's
aspeed: sbc: Allow per-machine settings
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change moves the code that connects the SoC UART's to serial_hd's
to the machine.
It makes each UART a proper child member of the SoC, and then allows the
machine to selectively initialize the chardev for each UART with a
serial_hd.
This should preserve backwards compatibility, but also allow multi-SoC
boards to completely change the wiring of serial devices from the
command line to specific SoC UART's.
This also removes the uart-default property from the SoC, since the SoC
doesn't need to know what UART is the "default" on the machine anymore.
I tested this using the images and commands from the previous
refactoring, and another test image for the ast1030:
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd
wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf
Fuji uses UART1:
qemu-system-arm -machine fuji-bmc \
-drive file=fuji.mtd,format=raw,if=mtd \
-nographic
ast2600-evb uses uart-default=UART5:
qemu-system-arm -machine ast2600-evb \
-drive file=fuji.mtd,format=raw,if=mtd \
-serial null -serial mon:stdio -display none
Wedge100 uses UART3:
qemu-system-arm -machine palmetto-bmc \
-drive file=wedge100.mtd,format=raw,if=mtd \
-serial null -serial null -serial null \
-serial mon:stdio -display none
AST1030 EVB uses UART5:
qemu-system-arm -machine ast1030-evb \
-kernel Y35BCL.elf -nographic
Fixes: 6827ff20b2 ("hw: aspeed: Init all UART's with serial devices")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-4-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds a passthrough for PMBUS_IC_DEVICE_ID to allow Renesas
voltage regulators to return the integrated circuit device ID if they
would like to.
The behavior is very device specific, so it hasn't been added to the
general PMBUS model. Additionally, if the device ID hasn't been set,
then the voltage regulator will respond with the error byte value. The
guest error message will change slightly for IC_DEVICE_ID with this
commit.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-3-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-2-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to correctly report secure boot running firmware the values
of certain registers must be set.
We don't yet have documentation from ASPEED on what they mean. The
meaning is inferred from u-boot's use of them.
Introduce properties so the settings can be configured per-machine.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Tested-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20220628154740.1117349-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When A/UX configures the CDROM device it sends a truncated MODE SELECT request
for page 1 (MODE_PAGE_R_W_ERROR) which is only 6 bytes in length rather than
10. This seems to be due to bug in Apple's code which calculates the CDB message
length incorrectly.
The work at [1] suggests that this truncated request is accepted on real
hardware whereas in QEMU it generates an INVALID_PARAM_LEN sense code which
causes A/UX to get stuck in a loop retrying the command in an attempt to succeed.
Alter the mode page request length check so that truncated requests are allowed
if the SCSI_DISK_QUIRK_MODE_PAGE_TRUNCATED quirk is enabled, whilst also adding a
trace event to enable the condition to be detected.
[1] https://68kmla.org/bb/index.php?threads/scsi2sd-project-anyone-interested.29040/page-7#post-316444
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both MacOS and A/UX make use of vendor-specific MODE SELECT commands with PF=0
to identify SCSI devices:
- MacOS sends a MODE SELECT command with PF=0 for the MODE_PAGE_VENDOR_SPECIFIC
(0x0) mode page containing 2 bytes before initialising a disk
- A/UX (installed on disk) sends a MODE SELECT command with PF=0 during SCSI
bus enumeration, and gets stuck in an infinite loop if it fails
Add a new SCSI_DISK_QUIRK_MODE_PAGE_VENDOR_SPECIFIC_APPLE quirk to allow both
PF=0 MODE SELECT commands and implement a MODE_PAGE_VENDOR_SPECIFIC (0x0)
mode page which is compatible with MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During SCSI bus enumeration A/UX sends a MODE SENSE command to the CDROM with
the DBD bit unset and expects the response to include a block descriptor. As per
the latest SCSI documentation, QEMU currently force-disables the block
descriptor for CDROM devices but the A/UX driver expects the requested block
descriptor to be returned.
If the block descriptor is not returned in the response then A/UX becomes
confused, since the block descriptor returned in the MODE SENSE response is
used to generate a subsequent MODE SELECT command which is then invalid.
Add a new SCSI_DISK_QUIRK_MODE_SENSE_ROM_USE_DBD quirk to allow this behaviour
to be enabled as required. Note that an additional workaround is required for
the previous SCSI_DISK_QUIRK_MODE_PAGE_APPLE_VENDOR quirk which must never
return a block descriptor even though the DBD bit is left unset.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One of the mechanisms MacOS uses to identify CDROM drives compatible with MacOS
is to send a custom MODE SELECT command for page 0x30 to the drive. The
response to this is a hard-coded manufacturer string which must match in order
for the CDROM to be usable within MacOS.
Add an implementation of the MODE SELECT page 0x30 response guarded by a newly
defined SCSI_DISK_QUIRK_MODE_PAGE_APPLE_VENDOR quirk bit so that CDROM drives
attached to non-Apple machines function exactly as before.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In 60592cfed2 ("hw/arm/virt: dt: add kaslr-seed property"), the
kaslr-seed property was added, but the equally as important rng-seed
property was forgotten about, which has identical semantics for a
similar purpose. This commit implements it in exactly the same way as
kaslr-seed. It then changes the name of the disabling option to reflect
that this has more to do with randomness vs determinism, rather than
something particular about kaslr.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[PMM: added deprecated.rst section for the deprecation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new PAPR 2.12 defines a watchdog facility managed via the new
H_WATCHDOG hypercall.
This adds H_WATCHDOG support which a proposed driver for pseries uses:
https://patchwork.ozlabs.org/project/linuxppc-dev/list/?series=303120
This was tested by running QEMU with a debug kernel and command line:
-append \
"pseries-wdt.timeout=60 pseries-wdt.nowayout=1 pseries-wdt.action=2"
and running "echo V > /dev/watchdog0" inside the VM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220622051008.1067464-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
It keeps repeating, move it to the header. This uses __builtin_ffsll() to
allow using the macros in #define.
This is not using the QEMU's FIELD macros as this would require changing
all such macros found in skiboot (the PPC PowerNV firmware).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220628080544.1509428-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
PAPR+/LoPAPR says:
===
The platform must restore the default DMA window for the PE on a call
to the ibm,remove-pe-dma-window RTAS call when all of the following
are true:
a. The call removes the last DMA window remaining for the PE.
b. The DMA window being removed is not the default window
===
This resets DMA as PAPR mandates.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220622052955.1069903-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
It is not advisable to execute an object_dynamic_cast() to poke into
bus->qbus.parent and follow it up with a C cast into the PnvPHB type we
think we got.
In fact this is not needed. There is nothing sophisticated being done
with the PHB object retrieved during root_port_realize() for both PHB3
and PHB4. We're retrieving a PHB reference just to access phb->chip_id
and phb->phb_id and use them to define the chassis/slot of the root
port.
phb->phb_id is already being passed to pnv_phb_attach_root_port() via
the 'index' parameter. Let's also add a 'chip_id' parameter to this
function and assign chassis and slot right there. This will spare us
from the hassle of accessing the PHB object inside realize().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220621173436.165912-4-danielhb413@gmail.com>
In general loongarch ipi device, 32bit registers is emulated, however for
anysend/mailsend device only 64bit register access is supported. So separate
the ipi memory region into two regions, including 32 bits and 64 bits.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220705064901.2353349-2-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Loongarch pch msi intc connects to extioi controller, the range of irq
number is 64-255. Add a property for irqbase, so that we can compute
the irq offset from the view of pch_msi controller with the method:
msi vector (from view of upper extioi intc) - irqbase
Signed-off-by: Mao Bibo <maobibo@loongson.cn>
Message-Id: <20220701030740.2469162-1-maobibo@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the Aspeed machines allocate a ram container region in
which the machine ram region is mapped. See commit ad1a978218
("aspeed: add a RAM memory region container"). An extra region is
mapped after ram in the ram container to catch invalid access done by
FW. That's how FW determines the size of ram. See commit ebe31c0a8e
("aspeed: add a max_ram_size property to the memory controller").
Let's move all the logic under the SoC where it should be. It will
also ease the work on multi SoC support.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220623202123.3972977-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
xen_piix_pci_write_config_client() is implemented in the xen sub tree and
uses PIIX constants internally, thus creating a direct dependency on
PIIX. Now that xen_set_pci_link_route() is stubbable, the logic of
xen_piix_pci_write_config_client() can be moved to PIIX which resolves
the dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-3-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The only user of xen_set_pci_link_route() is
xen_piix_pci_write_config_client() which implements PIIX-specific logic in
the xen namespace. This makes xen-hvm depend on PIIX which could be
avoided if xen_piix_pci_write_config_client() was implemented in PIIX. In
order to do this, xen_set_pci_link_route() needs to be stubbable which
this patch addresses.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-2-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
pi440fx_state is an out-parameter which is never read by the caller.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220612192800.40813-1-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220524154056.2896913-5-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220524154056.2896913-4-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Vhost has error notifications, let's log them like other errors.
For each virt-queue setup eventfd for vring error notifications.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
[vsementsov: rename patch, change commit message and dump error like
other errors in the file]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Message-Id: <20220623161325.18813-3-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Roman Kagan <rvkagan@yandex-team.ru>
Kernel and user vhost may report virtqueue errors via eventfd.
This is only reliable way to get notification about protocol error.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Message-Id: <20220623161325.18813-2-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Roman Kagan <rvkagan@yandex-team.ru>
Now that all the PS2 devices have been converted to use GPIOs the update_irq()
callback function and the update_arg parameter can be removed.
This allows these arguments to be completely removed from ps2_kbd_init() and
ps2_mouse_init(), along with the transitional logic that was added to
ps2_raise_irq() and ps2_lower_irq().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-55-mark.cave-ayland@ilande.co.uk>
This describes the I8042 device interface implemented within QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220624134109.881989-54-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This describes the I8042_MMIO device interface implemented within QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220624134109.881989-51-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This describes the LASI PS2 device interface implemented within QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220624134109.881989-49-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This is in preparation for handling vmstate_register() within the device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-45-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Now that the register memory regions are exposed as SysBus memory regions, move
the mapping of the LASIPS2 registers from lasips2_initfn() to the HPPA machine
(which is its only user).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-43-mark.cave-ayland@ilande.co.uk>
When QOMifying a device it is typical to use _init() as the suffix for an
instance_init function, however this name is already in use by the legacy LASIPS2
wrapper function. Eventually the wrapper function will be removed, but for now
rename it to lasips2_initfn() to avoid a naming collision.
At the same time update lasips2_initfn() return the LASIPS2 device so that it
can later be accessed using qdev APIs by the HPPA machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-41-mark.cave-ayland@ilande.co.uk>
This allows the QOM types in lasips2.c to be used elsewhere by simply including
lasips2.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-40-mark.cave-ayland@ilande.co.uk>
This allows both IRQs to be declared as a single qdev gpio array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-36-mark.cave-ayland@ilande.co.uk>
Define the gpio for the PS2 output IRQ in ps2_init() and add logic to optionally
use it in ps2_raise_irq() and ps2_lower_irq() if the gpio is connected. If the
gpio is not connected then call the legacy update_irq() function as before.
This allows the incremental conversion of devices from the legacy update_irq()
function to use gpios instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-35-mark.cave-ayland@ilande.co.uk>
This function is no longer used outside of ps2.c and so can be declared static.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-32-mark.cave-ayland@ilande.co.uk>
Now that the register memory region is exposed as a SysBus memory region, move
the mapping of the I8042_MMIO registers from i8042_mm_init() to the MIPS magnum
machine (which is its only user).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-29-mark.cave-ayland@ilande.co.uk>
This exposes the I8042_MMIO device to the caller to allow the register memory
region to be mapped outside of i8042_mm_init().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-28-mark.cave-ayland@ilande.co.uk>
Move the initialisation of the register memory region to the I8042_MMIO device
realize function and expose it using sysbus_init_mmio().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-26-mark.cave-ayland@ilande.co.uk>
This will soon be used to set the size of the register memory region using a
qdev property.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-25-mark.cave-ayland@ilande.co.uk>
Currently i8042_mm_init() creates a new KBDState directly which is used by the MIPS
magnum machine. Introduce a new I8042_MMIO QOM type that will soon be used to
allow the MIPS magnum machine to be wired up using standard qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220624134109.881989-22-mark.cave-ayland@ilande.co.uk>
This allows the QOM types in pckbd.c to be used elsewhere by simply including
i8042.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-21-mark.cave-ayland@ilande.co.uk>
This allows the QOM types in pckbd.c to be used elsewhere by simply including
i8042.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-20-mark.cave-ayland@ilande.co.uk>
The functionality of ps2_common_reset() can be moved into a new ps2_reset() function
for the PS2_DEVICE QOM type. Update PS2DeviceClass to hold a reference to the parent
reset function and update the PS2_KBD_DEVICE and PS2_MOUSE_DEVICE types to use
device_class_set_parent_reset() accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-9-mark.cave-ayland@ilande.co.uk>
This is in preparation for allowing the new PS2_KBD_DEVICE and PS2_MOUSE_DEVICE
QOM types to reference the parent PS2_DEVICE device reset() function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-8-mark.cave-ayland@ilande.co.uk>
With the latest changes it is now possible to improve some of the function
prototypes in ps2.c and ps.h to use the appropriate PS2KbdState or
PS2MouseState type instead of being a void opaque.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-7-mark.cave-ayland@ilande.co.uk>
Move the QOM type definitions into the ps2.h header file to allow the new QOM
types to be used by other devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220624134109.881989-6-mark.cave-ayland@ilande.co.uk>
This patch implements initial support for Single Root I/O Virtualization
on an NVMe device.
Essentially, it allows to define the maximum number of virtual functions
supported by the NVMe controller via sriov_max_vfs parameter.
Passing a non-zero value to sriov_max_vfs triggers reporting of SR-IOV
capability by a physical controller and ARI capability by both the
physical and virtual function devices.
NVMe controllers created via virtual functions mirror functionally
the physical controller, which may not entirely be the case, thus
consideration would be needed on the way to limit the capabilities of
the VF.
NVMe subsystem is required for the use of SR-IOV.
Signed-off-by: Lukasz Maniak <lukasz.maniak@linux.intel.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Occasionally a peripheral will have different operating modes, where the
MMIO layout changes, but some of the register fields have the same offsets
and behaviors.
To help support this, we add SHARED_FIELD_XX macros that create SHIFT,
LENGTH, and MASK macros for the fields that are shared across registers,
and accessors for these fields.
An example use may look as follows:
There is a peripheral with registers REG_MODE1 and REG_MODE2 at
different addreses, and both have a field FIELD1 initialized by
SHARED_FIELD().
Depending on what mode the peripheral is operating in, the user could
extract FIELD1 via
SHARED_ARRAY_FIELD_EX32(s->regs, R_REG_MODE1, FIELD1)
or
SHARED_ARRAY_FIELD_EX32(s->regs, R_REG_MODE2, FIELD1)
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Id3dc53e7d2f8741c95697cbae69a81bb699fa3cb
Message-Id: <20220331043248.2237838-2-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are two parts in this patch:
1, support akcipher service by cryptodev-builtin driver
2, virtio-crypto driver supports akcipher service
In principle, we should separate this into two patches, to avoid
compiling error, merge them into one.
Then virtio-crypto gets request from guest side, and forwards the
request to builtin driver to handle it.
Test with a guest linux:
1, The self-test framework of crypto layer works fine in guest kernel
2, Test with Linux guest(with asym support), the following script
test(note that pkey_XXX is supported only in a newer version of keyutils):
- both public key & private key
- create/close session
- encrypt/decrypt/sign/verify basic driver operation
- also test with kernel crypto layer(pkey add/query)
All the cases work fine.
Run script in guest:
rm -rf *.der *.pem *.pfx
modprobe pkcs8_key_parser # if CONFIG_PKCS8_PRIVATE_KEY_PARSER=m
rm -rf /tmp/data
dd if=/dev/random of=/tmp/data count=1 bs=20
openssl req -nodes -x509 -newkey rsa:2048 -keyout key.pem -out cert.pem -subj "/C=CN/ST=BJ/L=HD/O=qemu/OU=dev/CN=qemu/emailAddress=qemu@qemu.org"
openssl pkcs8 -in key.pem -topk8 -nocrypt -outform DER -out key.der
openssl x509 -in cert.pem -inform PEM -outform DER -out cert.der
PRIV_KEY_ID=`cat key.der | keyctl padd asymmetric test_priv_key @s`
echo "priv key id = "$PRIV_KEY_ID
PUB_KEY_ID=`cat cert.der | keyctl padd asymmetric test_pub_key @s`
echo "pub key id = "$PUB_KEY_ID
keyctl pkey_query $PRIV_KEY_ID 0
keyctl pkey_query $PUB_KEY_ID 0
echo "Enc with priv key..."
keyctl pkey_encrypt $PRIV_KEY_ID 0 /tmp/data enc=pkcs1 >/tmp/enc.priv
echo "Dec with pub key..."
keyctl pkey_decrypt $PRIV_KEY_ID 0 /tmp/enc.priv enc=pkcs1 >/tmp/dec
cmp /tmp/data /tmp/dec
echo "Sign with priv key..."
keyctl pkey_sign $PRIV_KEY_ID 0 /tmp/data enc=pkcs1 hash=sha1 > /tmp/sig
echo "Verify with pub key..."
keyctl pkey_verify $PRIV_KEY_ID 0 /tmp/data /tmp/sig enc=pkcs1 hash=sha1
echo "Enc with pub key..."
keyctl pkey_encrypt $PUB_KEY_ID 0 /tmp/data enc=pkcs1 >/tmp/enc.pub
echo "Dec with priv key..."
keyctl pkey_decrypt $PRIV_KEY_ID 0 /tmp/enc.pub enc=pkcs1 >/tmp/dec
cmp /tmp/data /tmp/dec
echo "Verify with pub key..."
keyctl pkey_verify $PUB_KEY_ID 0 /tmp/data /tmp/sig enc=pkcs1 hash=sha1
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: lei he <helei.sig11@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220611064243.24535-2-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When switching address space with mutex lock hold, mapping will be
replayed for assigned device. This will trigger relock deadlock.
Also release the mutex resource in unrealize routine.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220613061010.2674054-3-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently assigned devices can not work in virtio-iommu bypass mode.
Guest driver fails to probe the device due to DMA failure. And the
reason is because of lacking GPA -> HPA mappings when VM is created.
Add a root container memory region to hold both bypass memory region
and iommu memory region, so the switch between them is supported
just like the implementation in virtual VT-d.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220613061010.2674054-2-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
An initial simple upstream port emulation to allow the creation
of CXL switches. The Device ID has been allocated for this use.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220616145126.8002-2-Jonathan.Cameron@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Forward remote device's interrupts to the guest
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Message-id: 9523479eaafe050677f4de2af5dd0df18c27cfd9.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Assign separate address space for each device in the remote processes.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: afe0b0a97582cdad42b5b25636a29c523265a10a.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Define vfio-user object which is remote process server for QEMU. Setup
object initialization functions and properties necessary to instantiate
the object
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: e45a17001e9b38f451543a664ababdf860e5f2f2.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add vfio-user to x-remote machine. It is a boolean, which indicates if
the machine supports vfio-user protocol. The machine configures the bus
differently vfio-user and multiprocess protocols, so this property
informs it on how to configure the bus.
This property should be short lived. Once vfio-user fully replaces
multiprocess, this property could be removed.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 5d51a152a419cbda35d070b8e49b772b60a7230a.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
John Millikin