When you run QEMU with an Aspeed machine and a single serial device
using stdio like this:
qemu -machine ast2600-evb -drive ... -serial stdio
The guest OS can read and write to the UART5 registers at 0x1E784000 and
it will receive from stdin and write to stdout. The Aspeed SoC's have a
lot more UART's though (AST2500 has 5, AST2600 has 13) and depending on
the board design, may be using any of them as the serial console. (See
"stdout-path" in a DTS to check which one is chosen).
Most boards, including all of those currently defined in
hw/arm/aspeed.c, just use UART5, but some use UART1. This change adds
some flexibility for different boards without requiring users to change
their command-line invocation of QEMU.
I tested this doesn't break existing code by booting an AST2500 OpenBMC
image and an AST2600 OpenBMC image, each using UART5 as the console.
Then I tested switching the default to UART1 and booting an AST2600
OpenBMC image that uses UART1, and that worked too.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901153615.2746885-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
UART5 is typically used as the default debug UART on the AST2600, but
UART1 is also designed to be a debug UART. All the AST2600 UART's have
semi-configurable clock rates through registers in the System Control
Unit (SCU), but only UART5 works out of the box with zero-initialized
values. The rest of the UART's expect a few of the registers to be
initialized to non-zero values, or else the clock rate calculation will
yield zero or undefined (due to a divide-by-zero).
For reference, the U-Boot clock rate driver here shows the calculation:
https://github.com/facebook/openbmc-uboot/blob/15f7e0dc01d8/drivers/clk/aspeed/clk_ast2600.c#L357
To summarize, UART5 allows selection from 4 rates: 24 MHz, 192 MHz, 24 /
13 MHz, and 192 / 13 MHz. The other UART's allow selecting either the
"low" rate (UARTCLK) or the "high" rate (HUARTCLK). UARTCLK and HUARTCLK
are configurable themselves:
UARTCLK = UXCLK * R / (N * 2)
HUARTCLK = HUXCLK * HR / (HN * 2)
UXCLK and HUXCLK are also configurable, and depend on the APLL and/or
HPLL clock rates, which also derive from complicated calculations. Long
story short, there's lots of multiplication and division from
configurable registers, and most of these registers are zero-initialized
in QEMU, which at best is unexpected and at worst causes this clock rate
driver to hang from divide-by-zero's. This can also be difficult to
diagnose, because it may cause U-Boot to hang before serial console
initialization completes, requiring intervention from gdb.
This change just initializes all of these registers with default values
from the datasheet.
To test this, I used Facebook's AST2600 OpenBMC image for "fuji", with
the following diff applied (because fuji uses UART1 for console output,
not UART5).
@@ -323,8 +323,8 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)
}
/* UART - attach an 8250 to the IO space as our UART5 */
- serial_mm_init(get_system_memory(), sc->memmap[ASPEED_DEV_UART5], 2,
- aspeed_soc_get_irq(s, ASPEED_DEV_UART5),
+ serial_mm_init(get_system_memory(), sc->memmap[ASPEED_DEV_UART1], 2,
+ aspeed_soc_get_irq(s, ASPEED_DEV_UART1),
38400, serial_hd(0), DEVICE_LITTLE_ENDIAN);
/* I2C */
Without these clock rate registers being initialized, U-Boot hangs in
the clock rate driver from a divide-by-zero, because the UART1 clock
rate register reads return zero, and there's no console output. After
initializing them with default values, fuji boots successfully.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg: Removed _PARAM suffix ]
Message-Id: <20210906134023.3711031-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Witherspoon uses the DPS310 as a temperature sensor. Rainier uses it as
a temperature and humidity sensor.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210629142336.750058-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is the latest revision of the ASPEED 2600 SoC. As there is no
need to model multiple revisions of the same SoC for the moment,
update the SCU AST2600 to model the A3 revision instead of the A1 and
adapt the AST2600 SoC and machines.
Reset values are taken from v8 of the datasheet.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Introduced an Aspeed "ast2600-a3" SoC class
- Commit log update ]
Message-Id: <20210629142336.750058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These are the devices documented by the Rainier device tree. With this
we can see the guest discovering the multiplexers and probing the eeprom
devices:
i2c i2c-2: Added multiplexed i2c bus 16
i2c i2c-2: Added multiplexed i2c bus 17
i2c i2c-2: Added multiplexed i2c bus 18
i2c i2c-2: Added multiplexed i2c bus 19
i2c-mux-gpio i2cmux: 4 port mux on 1e78a180.i2c-bus adapter
at24 20-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 20
at24 21-0051: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 21
at24 22-0052: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: Introduced aspeed_eeprom_init ]
Message-Id: <20210629142336.750058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There was a bit of a thinko in the state calculation where every odd pin
in was reported in e.g. "pwm0" mode rather than "off". This was the
result of an incorrect bit shift for the 2-bit field representing each
LED state.
Fixes: a90d8f8467 ("misc/pca9552: Add qom set and get")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210723043624.348158-1-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are two GPIO controllers in the ast2600; one is 3.3V and the other
is 1.8V.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210713065854.134634-4-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There's no need to define the registers relative to the 0x800 offset
where the controller is mapped, as the device is instantiated as it's
own model at the correct memory address.
Simplify the defines and remove the offset to save future confusion.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210713065854.134634-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The logic in the handling for the control register required toggling the
enable state for writes to stick. Rework the condition chain to allow
sequential writes that do not update the enable state.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
While some of the critical fields remain the same, there is variation in
the definition of the control register across the SoC generations.
Reserved regions are adjusted, while in other cases the mutability or
behaviour of fields change.
Introduce a callback to sanitize the value on writes to ensure model
behaviour reflects the hardware.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to its dts file in the Linux kernel, we need mac0 and mac1 enabled
instead of mac1 and mac2. Also, g220a is based on aspeed-g5 (ast2500) which
doesn't even have the third interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210810035742.550391-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Commit 7582591ae7 ("aspeed: Support AST2600A1 silicon revision") switched
the silicon revision for AST2600 to revision A1. On revision A1, the first
Ethernet interface is operational. Enable it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210808200457.889955-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When mergeable buffer is enabled, we try to set the num_buffers after
the virtqueue elem has been unmapped. This will lead several issues,
E.g a use after free when the descriptor has an address which belongs
to the non direct access region. In this case we use bounce buffer
that is allocated during address_space_map() and freed during
address_space_unmap().
Fixing this by storing the elems temporarily in an array and delay the
unmap after we set the the num_buffers.
This addresses CVE-2021-3748.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: fbe78f4f55 ("virtio-net support")
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Adding this callback provides a way to resume the processing of
cmds in fenceq and cmdq that were not processed because the UI
was waiting on a fence and blocked cmd processing.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-6-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create sync objects and fences only for dmabufs that are blobs. Once a
fence is created (after glFlush) and is signalled,
graphic_hw_gl_flushed() will be called and virtio-gpu cmd processing
will be resumed.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-4-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* mark MPS2/MPS3 board-internal i2c buses as 'full' so that command
line user-created devices are not plugged into them
* Take an exception if PSTATE.IL is set
* Support an emulated ITS in the virt board
* Add support for kudo-bmc board
* Probe for KVM_CAP_ARM_VM_IPA_SIZE when creating scratch VM
* cadence_uart: Fix clock handling issues that prevented
u-boot from running
-----BEGIN PGP SIGNATURE-----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=7BH/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210913-3' into staging
target-arm queue:
* mark MPS2/MPS3 board-internal i2c buses as 'full' so that command
line user-created devices are not plugged into them
* Take an exception if PSTATE.IL is set
* Support an emulated ITS in the virt board
* Add support for kudo-bmc board
* Probe for KVM_CAP_ARM_VM_IPA_SIZE when creating scratch VM
* cadence_uart: Fix clock handling issues that prevented
u-boot from running
# gpg: Signature made Mon 13 Sep 2021 21:04:52 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210913-3: (23 commits)
hw/arm/mps2.c: Mark internal-only I2C buses as 'full'
hw/arm/mps2-tz.c: Mark internal-only I2C buses as 'full'
hw/arm/mps2-tz.c: Add extra data parameter to MakeDevFn
qdev: Support marking individual buses as 'full'
target/arm: Merge disas_a64_insn into aarch64_tr_translate_insn
target/arm: Take an exception if PSTATE.IL is set
tests/data/acpi/virt: Update IORT files for ITS
hw/arm/virt: add ITS support in virt GIC
tests/data/acpi/virt: Add IORT files for ITS
hw/intc: GICv3 redistributor ITS processing
hw/intc: GICv3 ITS Feature enablement
hw/intc: GICv3 ITS Command processing
hw/intc: GICv3 ITS command queue framework
hw/intc: GICv3 ITS register definitions added
hw/intc: GICv3 ITS initial framework
hw/arm: Add support for kudo-bmc board.
hw/arm/virt: KVM: Probe for KVM_CAP_ARM_VM_IPA_SIZE when creating scratch VM
hw/char: cadence_uart: Log a guest error when device is unclocked or in reset
hw/char: cadence_uart: Ignore access when unclocked or in reset for uart_{read, write}()
hw/char: cadence_uart: Convert to memop_with_attrs() ops
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The various MPS2 boards implemented in mps2.c have multiple I2C
buses: a bus dedicated to the audio configuration, one for the LCD
touchscreen controller, and two which are connected to the external
Shield expansion connector. Mark the buses which are used only for
board-internal devices as 'full' so that if the user creates i2c
devices on the commandline without specifying a bus name then they
will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-5-peter.maydell@linaro.org
The various MPS2 boards have multiple I2C buses: typically a bus
dedicated to the audio configuration, one for the LCD touchscreen
controller, one for a DDR4 EEPROM, and two which are connected to the
external Shield expansion connector. Mark the buses which are used
only for board-internal devices as 'full' so that if the user creates
i2c devices on the commandline without specifying a bus name then
they will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-4-peter.maydell@linaro.org
The mps2-tz boards use a data-driven structure to create the devices
that sit behind peripheral protection controllers. Currently the
functions which create these devices are passed an 'opaque' pointer
which is always the address within the machine struct of the device
to create, and some "all devices need this" information like irqs and
addresses.
If a specific device needs more information than this, it is
currently not possible to pass that through from the PPCInfo
data structure. Add support for passing an extra data parameter,
so that we can more flexibly handle the needs of specific
device types. To provide some type-safety we make this extra
parameter a pointer to a union (which initially has no members).
In particular, we would like to be able to indicate which of the
i2c controllers are for on-board devices only and which are
connected to the external 'shield' expansion port; a subsequent
patch will use this mechanism for that purpose.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-3-peter.maydell@linaro.org
Included creation of ITS as part of virt platform GIC
initialization. This Emulated ITS model now co-exists with kvm
ITS and is enabled in absence of kvm irq kernel support in a
platform.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-9-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implemented lpi processing at redistributor to get lpi config info
from lpi configuration table,determine priority,set pending state in
lpi pending table and forward the lpi to cpuif.Added logic to invoke
redistributor lpi processing with translated LPI which set/clear LPI
from ITS device as part of ITS INT,CLEAR,DISCARD command and
GITS_TRANSLATER processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-7-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added properties to enable ITS feature and define qemu system
address space memory in gicv3 common,setup distributor and
redistributor registers to indicate LPI support.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-6-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added ITS command queue handling for MAPTI,MAPI commands,handled ITS
translation which triggers an LPI via INT command as well as write
to GITS_TRANSLATER register,defined enum to differentiate between ITS
command interrupt trigger and GITS_TRANSLATER based interrupt trigger.
Each of these commands make use of other functionalities implemented to
get device table entry,collection table entry or interrupt translation
table entry required for their processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-5-shashi.mallela@linaro.org
[PMM: use INTERRUPT for ItsCmdType enum name to avoid
conflict with INT type defined by Windows headers]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added functionality to trigger ITS command queue processing on
write to CWRITE register and process each command queue entry to
identify the command type and handle commands like MAPD,MAPC,SYNC.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-4-shashi.mallela@linaro.org
[PMM: fixed format string nit]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Defined descriptors for ITS device table,collection table and ITS
command queue entities.Implemented register read/write functions,
extract ITS table parameters and command queue parameters,extended
gicv3 common to capture qemu address space(which host the ITS table
platform memories required for subsequent ITS processing) and
initialize the same in ITS device.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-3-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added register definitions relevant to ITS,implemented overall
ITS device framework with stubs for ITS control and translater
regions read/write,extended ITS common to handle mmio init between
existing kvm device and newer qemu device.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-2-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've got SW that expects FSBL (Bootlooader) to setup clocks and
resets. It's quite common that users run that SW on QEMU without
FSBL (FSBL typically requires the Xilinx tools installed). That's
fine, since users can stil use -device loader to enable clocks etc.
To help folks understand what's going, a log (guest-error) message
would be helpful here. In particular with the serial port since
things will go very quiet if they get things wrong.
Suggested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-7-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Read or write to uart registers when unclocked or in reset should be
ignored. Add the check there, and as a result of this, the check in
uart_write_tx_fifo() is now unnecessary.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-6-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This converts uart_read() and uart_write() to memop_with_attrs() ops.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-5-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the clock/reset check is done in uart_receive(), but we
can move the check to uart_can_receive() which is earlier.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present when input clock is disabled, any character transmitted
to tx fifo can still show on the serial line, which is wrong.
Fixes: b636db306e ("hw/char/cadence_uart: add clock support")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210901124521.30599-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of today, when booting upstream U-Boot for Xilinx Zynq, the UART
does not receive anything. Debugging shows that the UART input clock
frequency is zero which prevents the UART from receiving anything as
per the logic in uart_receive().
From zynq_slcr_reset_exit() comment, it intends to compute output
clocks according to ps_clk and registers. zynq_slcr_compute_clocks()
is called to accomplish the task, inside which device_is_in_reset()
is called to actually make the attempt in vain.
Rework reset_hold() and reset_exit() so that in the reset exit phase,
the logic can really compute output clocks in reset_exit().
With this change, upstream U-Boot boots properly again with:
$ qemu-system-arm -M xilinx-zynq-a9 -m 1G -display none -serial null -serial stdio \
-device loader,file=u-boot-dtb.bin,addr=0x4000000,cpu-num=0
Fixes: 38867cb7ec ("hw/misc/zynq_slcr: add clock generation for uarts")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210901124521.30599-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The file already existed, but nobody had noticed the warning until now.
Add it at the bottom, since that is where unknown files go in legacy mode.
Fixes: 217f1b4a72 ("target-i386: Publish advised value of MSR_IA32_FEATURE_CONTROL via fw_cfg")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A PS/2 keyboard has a separate command reply queue that is
independent of the key queue. This prevents that command replies
and keyboard input mix. Keyboard command replies take precedence
over queued keystrokes. A new keyboard command removes any
remaining command replies from the command reply queue.
Implement a separate keyboard command reply queue and clear the
command reply queue before command execution. This brings the
PS/2 keyboard emulation much closer to a real PS/2 keyboard.
The command reply queue is located in a few free bytes directly
in front of the scancode queue. Because the scancode queue has
a maximum length of 16 bytes there are 240 bytes available for
the command reply queue. At the moment only a maximum of 3 bytes
are required. For compatibility reasons rptr, wptr and count kept
their function. rptr is the start, wptr is the end and count is
the length of the entire keyboard queue. The new variable cwptr
is the end of the command reply queue or -1 if the queue is
empty. To write to the command reply queue, rptr is moved
backward by the number of required bytes and the command replies
are written to the buffer starting at the new rptr position.
After writing, cwptr is at the old rptr position. Copying cwptr
to rptr clears the command reply queue. The command reply queue
can't overflow because each new keyboard command clears the
command reply queue.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/501
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/502
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210810133258.8231-2-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Extend the used ps2 buffer size to the available buffer size but
keep the maximum ps2 queue size.
The next patch needs a few bytes of the larger buffer size.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210810133258.8231-1-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
These will soon be required to enable nubus devices to support interrupts.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Now that q800 VIA1 and VIA2 are completely separate devices there is no need to
add a specific device prefix to ensure that the IRQ lines remain separate.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Peter Maydell