One of the functions of the ADU is indirect memory access engines that
send and receive data via ADU registers.
This implements the ADU LPC memory access functionality sufficiently
for IBM proprietary firmware to access the UART and print characters
to the serial port as it does on real hardware.
This requires a linkage between adu and lpc, which allows adu to
perform memory access in the lpc space.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The POWER8 LPC ISA device irqs all get combined and reported to the line
connected the PSI LPCHC irq. POWER9 changed this so only internal LPC
host controller irqs use that line, and the device irqs get routed to
4 new lines connected to PSI SERIRQ0-3.
POWER9 also introduced a new feature that automatically clears the irq
status in the LPC host controller when EOI'ed, so software does not have
to.
The powernv OPAL (skiboot) firmware managed to work because the LPCHC
irq handler scanned all LPC irqs and handled those including clearing
status even on POWER9 systems. So LPC irqs worked despite OPAL thinking
it was running in POWER9 mode. After this change, UART interrupts show
up on serirq1 which is where OPAL routes them to:
cat /proc/interrupts
...
20: 0 XIVE-IRQ 1048563 Level opal-psi#0:lpchc
...
25: 34 XIVE-IRQ 1048568 Level opal-psi#0:lpc_serirq_mux1
Whereas they previously turn up on lpchc.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The LPC HC irq status register bits are set when an LPC IRQSER input is
asserted. These irq status bits drive the PSI irq to the CPU interrupt
controller. The LPC HC irq status bits are cleared by software writing
to the register with 1's for the bits to clear.
Existing register write was clearing the irq status bits even when the
input was asserted, this results in interrupts being lost.
This fix changes the behavior to keep track of the device IRQ status
in internal state that is separate from the irq status register, and
only allowing the irq status bits to be cleared if the associated
input is not asserted.
Signed-off-by: Glenn Miles <milesg@linux.ibm.com>
[np: rebased before P9 PSI SERIRQ patch, adjust changelog/comments]
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Mechanical change running Coccinelle spatch with content
generated from the qom-cast-macro-clean-cocci-gen.py added
in the previous commit.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230601093452.38972-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
As lpc-hc is designed for re-entrant calls from xscom, mark it
re-entrancy safe.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
[clg: mark opb_master_regs as re-entrancy safe also ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230526073850.2772197-1-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
isa_bus_irqs() register an array of input IRQs on
the ISA bus. Rename it as isa_bus_register_input_irqs().
Mechanical change using:
$ sed -i -e 's/isa_bus_irqs/isa_bus_register_input_irqs/g' \
$(git grep -wl isa_bus_irqs)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-10-philmd@linaro.org>
PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip are defined
in pnv.h. Many users of the header don't actually need them. One
instance is this inclusion loop: hw/ppc/pnv_homer.h includes
hw/ppc/pnv.h for typedef PnvChip, and vice versa for struct PnvHomer.
Similar structs live in their own headers: PnvHomerClass and PnvHomer
in pnv_homer.h, PnvLpcClass and PnvLpcController in pci_lpc.h,
PnvPsiClass, PnvPsi, Pnv8Psi, Pnv9Psi, Pnv10Psi in pnv_psi.h, ...
Move PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip to new
pnv_chip.h, and adjust include directives. This breaks the inclusion
loop mentioned above.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221222104628.659681-2-armbru@redhat.com>
Create an anonymous output GPIO line to connect the LPC device with
the PSIHB device and raise the appropriate PSI IRQ line depending on
the processor model.
A temporary __pnv_psi_irq_set() routine is introduced to handle the
transition. It will be removed when all devices raising PSI interrupts
are converted to use GPIOs.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220323072846.1780212-3-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This to map the PNOR from the machine init handler directly and finish
the cleanup of the LPC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-8-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On PowerNV systems, the BMC is in charge of mapping the PNOR contents
on the LPC FW address space using the HIOMAP protocol. Under QEMU, we
emulate this behavior and we also add an extra control on the flash
accesses by letting the HIOMAP command handler decide whether the
memory region is accessible or not depending on the firmware requests.
However, this behavior is not compatible with hostboot like firmwares
which need this mapping to be always available. For this reason, the
PNOR memory region is initially disabled for skiboot mode only.
This is badly placed under the LPC model and requires the use of the
machine. Since it doesn't add much, simply remove the initial setting.
The extra control in the HIOMAP command handler will still be performed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-7-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201016145346.27167-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It was missing the instance_size field.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200822083920.2668930-1-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200228123303.14540-1-philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The address_space_rw() function allows either reads or writes
depending on the is_write argument passed to it; this is useful
when the direction of the access is determined programmatically
(as for instance when handling the KVM_EXIT_MMIO exit reason).
Under the hood it just calls either address_space_write() or
address_space_read_full().
We also use it a lot with a constant is_write argument, though,
which has two issues:
* when reading "address_space_rw(..., 1)" this is less
immediately clear to the reader as being a write than
"address_space_write(...)"
* calling address_space_rw() bypasses the optimization
in address_space_read() that fast-paths reads of a
fixed length
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.cocci.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200218112457.22712-1-peter.maydell@linaro.org>
[PMD: Update macvm_set_cr0() reported by Laurent Vivier]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The PowerNV machine emulates an OpenPOWER system and the PowerNV chip
devices are models of the internal logic of the POWER processor. They
can not be instantiated by the user on the QEMU command line.
The PHB3/PHB4 devices could be an exception in the future after some
rework on how the device tree is built. For the moment, exclude them
also.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200129113720.7404-1-clg@kaod.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the "hb-mode" option is activated on the powernv machine, the
firmware is mapped at 0x8000000 and the HRMOR of the HW threads are
set to the same address.
The PNOR mapping on the FW address space of the LPC bus is left enabled
to let the firmware load any other images required to boot the host.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144154.10170-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Same a POWER9, only the MMIO window changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This activates HIOMAP support on the QEMU PowerNV machine. The PnvPnor
model is used to access the flash contents. The model simply maps the
contents at a fix offset and enables or disables the mapping.
HIOMAP Protocol description :
https://github.com/openbmc/hiomapd/blob/master/Documentation/protocol.md
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191028070027.22752-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And fix a typo in the MEM address space definition.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191118091908.15044-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC object has both a pointer and a "psi" property pointing to the
PSI object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383334342.165747.3159314903077305653.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
This is just a simple reminder that SerIRQ routing should be
addressed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC Controller on POWER9 is very similar to the one found on
POWER8 but accesses are now done via on MMIOs, without the XSCOM and
ECCB logic. The device tree is populated differently so we add a
specific POWER9 routine for the purpose.
SerIRQ routing is yet to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will ease the introduction of the LPC Controller model for POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV LPC Controller exposes different sets of registers for
each of the functional units it encompasses, among which the OPB
(On-Chip Peripheral Bus) Master and Arbitrer and the LPC HOST
Controller.
The mapping addresses of each register range are correct but the sizes
are too large. Fix the sizes and define the OPB Arbitrer range to fill
the gap between the OPB Master registers and the LPC HOST Controller
registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A specific MemoryRegion is required for the LPC HC Firmware address
space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also introduce utilities to manipulate bitmasks (originaly from OPAL)
which be will be used in the model of the XIVE interrupt controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'pnv' prefix is now used for all and the routines populating the
device tree start with 'pnv_dt'. The handler of the PnvXScomInterface
is also renamed to 'dt_xscom' which should reflect that it is
populating the device tree under the 'xscom@' node of the chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The default LPC bus of a multichip system is on chip 0. It's
recognized by the firmware (skiboot) using a "primary" property in the
device tree.
We introduce a pnv_chip_lpc_offset() routine to locate the LPC node of
a chip and set the property directly from the machine level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It adds the Naples chip which supports proper LPC interrupts via the
LPC controller rather than via an external CPLD.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.9
- ported on latest PowerNV patchset
- moved the IRQ handler in pnv_lpc.c
- introduced pnv_lpc_isa_irq_create() to create the ISA IRQs ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
PnvChip is defined twice and this can confuse old compilers :
CC ppc64-softmmu/hw/ppc/pnv_xscom.o
In file included from qemu.git/hw/ppc/pnv.c:29:
qemu.git/include/hw/ppc/pnv.h:60: error: redefinition of typedef ‘PnvChip’
qemu.git/include/hw/ppc/pnv_xscom.h:24: note: previous declaration of ‘PnvChip’ was here
make[1]: *** [hw/ppc/pnv.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC (Low Pin Count) interface on a POWER8 is made accessible to
the system through the ADU (XSCOM interface). This interface is part
of set of units connected together via a local OPB (On-Chip Peripheral
Bus) which act as a bridge between the ADU and the off chip LPC
endpoints, like external flash modules.
The most important units of this OPB are :
- OPB Master: contains the ADU slave logic, a set of internal
registers and the logic to control the OPB.
- LPCHC (LPC HOST Controller): which implements a OPB Slave, a set of
internal registers and the LPC HOST Controller to control the LPC
interface.
Four address spaces are provided to the ADU :
- LPC Bus Firmware Memory
- LPC Bus Memory
- LPC Bus I/O (ISA bus)
- and the registers for the OPB Master and the LPC Host Controller
On POWER8, an intermediate hop is necessary to reach the OPB, through
a unit called the ECCB. OPB commands are simply mangled in ECCB write
commands.
On POWER9, the OPB master address space can be accessed via MMIO. The
logic is same but the code will be simpler as the XSCOM and ECCB hops
are not necessary anymore.
This version of the LPC controller model doesn't yet implement support
for the SerIRQ deserializer present in the Naples version of the chip
though some preliminary work is there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- ported on latest PowerNV patchset
- changed the XSCOM interface to fit new model
- QOMified the model
- moved the ISA hunks in another patch
- removed printf logging
- added a couple of UNIMP logging
- rewrote commit log ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Nicholas Piggin