Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
AST2700 interrupt controller(INTC) provides hardware interrupt interfaces
to interrupt of processors PSP, SSP and TSP. In INTC, each interrupt of
INT 128 to INT136 combines 32 interrupts.
Introduce a new aspeed_intc class with instance_init and realize handlers.
So far, this model only supports GICINT128 to GICINT136.
It creates 9 GICINT or-gates to connect 32 interrupts sources
from GICINT128 to GICINT136 as IRQ GPIO-OUTPUT pins.
Then, this model registers IRQ handler with its IRQ GPIO-INPUT pins which
connect to GICINT or-gates. And creates 9 GICINT IRQ GPIO-OUTPUT pins which
connect to GIC device with GIC IRQ 128 to 136.
If one interrupt source from GICINT128 to GICINT136
set irq, the OR-GATE irq callback function is called and set irq to INTC by
OR-GATE GPIO-OUTPUT pins. Then, the INTC irq callback function is called and
set irq to GIC by its GICINT IRQ GPIO-OUTPUT pins. Finally, the GIC irq
callback function is called and set irq to CPUs and
CPUs execute Interrupt Service Routine (ISR).
Block diagram of GICINT132:
GICINT132
ETH1 +-----------+
+-------->+0 3|
ETH2 | 4|
+-------->+1 5|
ETH3 | 6|
+-------->+2 19| INTC GIC
UART0 | 20| +--------------------------+
+-------->+7 21| | | +--------------+
UART1 | 22| |orgate0 +----> output_pin0+----------->+GIC128 |
+-------->+8 23| | | | |
UART2 | 24| |orgate1 +----> output_pin1+----------->+GIC129 |
+-------->+9 25| | | | |
UART3 | 26| |orgate2 +----> output_pin2+----------->+GIC130 |
+--------->10 27| | | | |
UART5 | 28| |orgate3 +----> output_pin3+----------->+GIC131 |
+-------->+11 29| | | | |
UART6 | +----------->+orgate4 +----> output_pin4+----------->+GIC132 |
+-------->+12 30| | | | |
UART7 | 31| |orgate5 +----> output_pin5+----------->+GIC133 |
+-------->+13 | | | | |
UART8 | OR[0:31] | |orgate6 +----> output_pin6+----------->+GIC134 |
---------->14 | | | | |
UART9 | | |orgate7 +----> output_pin7+----------->+GIC135 |
--------->+15 | | | | |
UART10 | | |orgate8 +----> output_pin8+----------->+GIC136 |
--------->+16 | | | +--------------+
UART11 | | +--------------------------+
+-------->+17 |
UART12 | |
+--------->18 |
| |
| |
| |
+-----------+
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
[clg: Fixed class_size in TYPE_ASPEED_INTC definition ]
Peter Maydell