In sdhci_sysbus_realize() we override the initialization of
s->iomem that sdhci_common_realize() performs. However we
don't destroy the old memory region before reinitializing
it, which means that the memory allocated for mr->name in
memory_region_do_init() is leaked.
Since sdhci_initfn() already initializes s->io_ops to
&sdhci_mmio_ops, always use that in sdhci_common_realize()
and remove the now-unnecessary reinitialization of the
MMIO region from sdhci_sysbus_realize().
Spotted by clang's leak sanitizer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181204132952.2601-4-peter.maydell@linaro.org
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
Device ssi-sd picks up its block backend in its init() method with
drive_get_next() instead. This mistake is already marked FIXME since
commit af9e40a.
Unset user_creatable to remove the mistake from our external
interface. Since the SSI bus doesn't support hotplug, only -device
can be affected. Only certain ARM machines have ssi-sd and provide an
SSI bus for it; this patch breaks -device ssi-sd for these machines.
No actual use of -device ssi-sd is known.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20181009060835.4608-1-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the ESDHC PRSSTAT_SDSTB bit, using the value of SDHC_CLOCK_INT_STABLE.
Freescale recommends checking this bit when changing clock frequency.
Signed-off-by: Hans-Erik Floryd <hans-erik.floryd@rt-labs.com>
Message-id: 1534507843-4251-1-git-send-email-hans-erik.floryd@rt-labs.com
[PMM: fixed indentation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Writes in PIO mode have two requirements:
- A data interrupt must be generated after a write command has been
issued to indicate that the chip is ready to receive data.
- A block interrupt must be generated after each block to indicate
that the chip is ready to receive the next data block.
Rearrange the code to make this happen. Tested on raspi3 (in PIO mode)
and raspi2 (in DMA mode).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1531779837-20557-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
DeviceClass::reset models a "cold power-on" reset which can
also be used to powercycle a device; but there is no "hot reset"
(a.k.a. soft-reset) method available.
The OMAP MMC Power-Up Control bit is not designed to powercycle
a card, but to disable it without powering it off (pseudo-reset):
Multimedia Card (MMC/SD/SDIO) Interface [SPRU765A]
MMC_CON[11] Power-Up Control (POW)
This bit must be set to 1 before any valid transaction to either
MMC/SD or SPI memory cards.
When 1, the card is considered powered-up and the controller core
is enabled.
When 0, the card is considered powered-down (system dependent),
and the controller core logic is in pseudo-reset state. This is,
the MMC_STAT flags and the FIFO pointers are reset, any access to
MMC_DATA[DATA] has no effect, a write into the MMC.CMD register
is ignored, and a setting of MMC_SPI[STR] to 1 is ignored.
By splitting the 'pseudo-reset' code out of the 'power-on' reset
function, this patch fixes a latent bug in omap_mmc_write(MMC_CON)i
recently exposed by ecd219f7ab.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180706162155.8432-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-37-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The load/store API will ease further code movement.
Per the Physical Layer Simplified Spec. "3.6 Bus Protocol":
"In the CMD line the Most Significant Bit (MSB) is transmitted
first, the Least Significant Bit (LSB) is the last."
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We don't actually implement SD command CRC checking, because
for almost all of our SD controllers the CRC generation is
done in hardware, and so modelling CRC generation and checking
would be a bit pointless. (The exception is that milkymist-memcard
makes the guest software compute the CRC.)
As a result almost all of our SD controller models don't bother
to set the SDRequest crc field, and the SD card model doesn't
check it. So the tracing of it in sdbus_do_command() provokes
Coverity warnings about use of uninitialized data.
Drop the CRC field from the trace; we can always add it back
if and when we do anything useful with the CRC.
Fixes Coverity issues 1386072, 1386074, 1386076, 1390571.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180626180324.5537-1-peter.maydell@linaro.org
Per the Physical Layer Simplified Spec. "5.3 CSD Register":
"The maximum block length might therefore be in the range 512...2048 bytes"
Therefore 3 hexdigits are enough to report the block length.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These commands got introduced by Spec v3
(see 0c3fb03f7e and 4481bbc79d).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180607180641.874-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CMD8 is "Reserved" in Spec v1.10.
Spec v2.00 introduces the SEND_IF_COND command:
6.4.1 Power Up
CMD8 is newly added in the Physical Layer Specification Version
2.00 to support multiple voltage ranges and used to check whether
the card supports supplied voltage. The version 2.00 or later host
shall issue CMD8 and verify voltage before card initialization.
The host that does not support CMD8 shall supply high voltage range.
Message-Id: 201204252110.20873.paul@codesourcery.com
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180607180641.874-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of this commit, the Spec v1 is not working, and all controllers
expect the cards to be conformant to Spec v2.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "Physical Layer Simplified Specification Version 1.10"
Chapter 7.3 "SPI Mode Transaction Packets"
Table 57: "Commands and arguments"
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The initial implementation is based on the Specs v1.10 (see a1bb27b1e9).
However the SCR is anouncing the card being v1.01.
The new chapters added in version 1.10 are:
4.3.10 Switch function command
Switch function command (CMD6) 1 is used to switch or expand
memory card functions. [...]
This is a new feature, introduced in SD physical Layer
Specification Version 1.10. Therefore, cards that are
compatible with earlier versions of the spec do not support
it. The host shall check the "SD_SPEC" field in the SCR
register to recognize what version of the spec the card
complies with before using CMD6. It is mandatory for SD
memory card of Ver1.10 to support CMD6.
4.3.11 High-Speed mode (25MB/sec interface speed)
Though the Rev 1.01 SD memory card supports up to 12.5MB/sec
interface speed, the speed of 25MB/sec is necessary to support
increasing performance needs of the host and because of memory
size which continues to grow.
To achieve 25MB/sec interface speed, clock rate is increased to
50MHz and CLK/CMD/DAT signal timing and circuit conditions are
reconsidered and changed from Physical Layer Specification
Version 1.01.
4.3.12 Command system (This chapter is newly added in version 1.10)
SD commands CMD34-37, CMD50, CMD57 are reserved for SD command
system expansion via the switch command.
[These commands] will be considered as illegal commands (as
defined in revision 1.01 of the SD physical layer specification).
The SWITCH_FUNCTION is implemented since the first commit, a1bb27b1e9.
The 25MB/sec High-Speed mode was already updated in d7ecb86752.
The current implementation does not implements CMD34-37, CMD50 and
CMD57, thus these commands already return ILLEGAL.
With this patch, the SCR register now matches the description of the header:
* SD Memory Card emulation as defined in the "SD Memory Card Physical
* layer specification, Version 1.10."
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180607180641.874-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606152128.449-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
include files shouldn't have the "include/" part, that is implied.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove those unneeded includes to speed up the compilation
process a little bit.
Code change produced with:
$ git grep '#include "sysemu/blockdev.h"' | \
cut -d: -f-1 | \
xargs egrep -L "(BlockInterfaceType|DriveInfo|drive_get|blk_legacy_dinfo|blockdev_mark_auto_del)" | \
xargs sed -i.bak '/#include "sysemu\/blockdev.h"/d'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-15-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per the Physical Layer Simplified Spec. "4.3.10.4 Switch Function Status":
The block length is predefined to 512 bits
and "4.10.2 SD Status":
The SD Status contains status bits that are related to the SD Memory Card
proprietary features and may be used for future application-specific usage.
The size of the SD Status is one data block of 512 bit. The content of this
register is transmitted to the Host over the DAT bus along with a 16-bit CRC.
Thus the 16-bit CRC goes at offset 64.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180509060104.4458-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Linux bcm2835_sdhost driver doesn't work on QEMU, because our
model raises spurious data interrupts. Our function
bcm2835_sdhost_fifo_run() will flag an interrupt any time it is
called with s->datacnt == 0, even if the host hasn't actually issued
a data read or write command yet. This means that the driver gets a
spurious data interrupt as soon as it enables IRQs and then does
something else that causes us to call the fifo_run routine, like
writing to SDHCFG, and before it does the write to SDCMD to issue the
read. The driver's IRQ handler then spins forever complaining that
there's no data and the SD controller isn't in a state where there's
going to be any data:
[ 41.040738] sdhost-bcm2835 3f202000.mmc: fsm 1, hsts 00000000
[ 41.042059] sdhost-bcm2835 3f202000.mmc: fsm 1, hsts 00000000
(continues forever).
Move the interrupt flag setting to more plausible places:
* for BUSY, raise this as soon as a BUSYWAIT command has executed
* for DATA, raise this when the FIFO has any space free (for a write)
or any data in it (for a read)
* for BLOCK, raise this when the data count is 0 and we've
actually done some reading or writing
This is pure guesswork since the documentation for this hardware is
not public, but it is sufficient to get the Linux bcm2835_sdhost
driver to work.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180319161556.16446-3-peter.maydell@linaro.org
Add some tracepoints to the bcm2835_sdhost driver, to assist
debugging.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180319161556.16446-2-peter.maydell@linaro.org
Detected by Coverity (CID 1386072, 1386073, 1386076, 1386077). local_err
was unused, and this made the static analyzer unhappy.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20180320151355.25854-1-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After reviewing a patch from Philippe that removes block-backend.h
from hw/lm32/milkymist.c, I noticed that this header is included
unnecessarily in a lot of other files, too. Remove those unneeded
includes to speed up the compilation process a little bit.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1518684912-31637-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180309153654.13518-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "Physical Layer Simplified Specification Version 3.01":
A known data block ("Tuning block") can be used to tune sampling
point for tuning required hosts. [...]
This procedure gives the system optimal timing for each specific
host and card combination and compensates for static delays in
the timing budget including process, voltage and different PCB
loads and skews. [...]
Data block, carried by DAT[3:0], contains a pattern for tuning
sampling position to receive data on the CMD and DAT[3:0] line.
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
from qemu/xilinx tag xilinx-v2015.2]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180309153654.13518-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180309153654.13518-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDBus will reuse these functions, so we put them in a new source file.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180309153654.13518-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: slight wordsmithing of comments, added note that string
returned does not need to be freed]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180309153654.13518-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-15-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-14-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-13-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
returning sd_illegal, since they are not implemented.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-11-f4bug@amsat.org
[PMM: tweak multiline comment format]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux uses it to poll the bus before polling for a card.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-9-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
use the registerfields API to access the OCR register
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
the code is easier to review/refactor.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This device does not model MMCA Specification previous to v4.2
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To comply with Spec v1.10 (and 2.00, 3.01):
. TRAN_SPEED
for current SD Memory Cards that field must be always 0_0110_010b (032h) which is
equal to 25MHz - the mandatory maximum operating frequency of SD Memory Card.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-4-f4bug@amsat.org
[PMM: fixed comment indent]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't set the high capacity bit by default as it will be set if required
in the sd_set_csd() function.
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
and Peter Ogden <ogden@xilinx.com> from qemu/xilinx tag xilinx-v2015.4]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
code is now easier to read.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-11-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-6-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180215220540.6556-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
place card registers first, this will ease further code movements.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On reset the bus will reset the card,
we can now drop the device_reset() call.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180216022933.10945-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
using the sdbus_*() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michael Walle <michael@walle.cc>
Message-id: 20180216022933.10945-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create the SDCard in the realize() function.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michael Walle <michael@walle.cc>
Message-id: 20180216022933.10945-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michael Walle <michael@walle.cc>
Message-id: 20180216022933.10945-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
from qemu/xilinx tag xilinx-v2015.2]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-23-f4bug@amsat.org>
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
from qemu/xilinx tag xilinx-v2015.2]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-22-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-21-f4bug@amsat.org>
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
from qemu/xilinx tag xilinx-v2015.2]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-20-f4bug@amsat.org>
As per the Spec v3.00
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-19-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-18-f4bug@amsat.org>
Incorrect value will throw an error.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-14-f4bug@amsat.org>
The 64-bit ADMA address is not converted to the cpu endianes correctly.
This patch fixes the issue and uses a valid mask for the attribute data.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
[AF: Re-write commit message]
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-13-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-12-f4bug@amsat.org>
Incorrect value will throw an error.
Note than Spec v2 is supported by default.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-11-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-10-f4bug@amsat.org>
using many #defines is not portable when scaling to different HCI.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-9-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <20180208164818.7961-8-f4bug@amsat.org>
-----BEGIN PGP SIGNATURE-----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=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
IP block found on several generations of i.MX family does not use
vanilla SDHCI implementation and it comes with a number of quirks.
Introduce i.MX SDHCI subtype of SDHCI block to add code necessary to
support unmodified Linux guest driver.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMM: define and use ESDHC_UNDOCUMENTED_REG27]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
[Most of original patch dropped, commit message replaced to match
what's left]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180203084315.20497-11-armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Add a 'dma' property allowing machine creation to provide the address-space
SDHCI DMA operates on.
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
from qemu/xilinx tag xilinx-v2016.1]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180115182436.2066-15-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While SysBus devices can use the get_system_memory() address space,
PCI devices should use the bus master address space for DMA.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180115182436.2066-14-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-11-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
zero-initialize ADMADescr 'dscr' in sdhci_do_adma() to avoid:
hw/sd/sdhci.c: In function ‘sdhci_do_adma’:
hw/sd/sdhci.c:714:29: error: ‘dscr.addr’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
trace_sdhci_adma("link", s->admasysaddr);
^
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now both inherited classes appear as DEVICE_CATEGORY_STORAGE.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add common/sysbus/pci/sdbus comments to have clearer code blocks separation.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180115182436.2066-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180115182436.2066-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since omap_mmc is still using the legacy SD card API, the SD
card created by sd_init() is not plugged into any bus. This
means that the controller has to reset it manually.
Failing to do this mostly didn't affect the guest since the
guest typically does a programmed SD card reset as part of
its SD controller driver initialization, but would mean that
migration fails because it's only in sd_reset() that we
set up the wpgrps_size field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1515506513-31961-5-git-send-email-peter.maydell@linaro.org
Since ssi-sd is still using the legacy SD card API, the SD
card created by sd_init() is not plugged into any bus. This
means that the controller has to reset it manually.
Failing to do this mostly didn't affect the guest since the
guest typically does a programmed SD card reset as part of
its SD controller driver initialization, but meant that
migration failed because it's only in sd_reset() that we
set up the wpgrps_size field.
In the case of sd-ssi, we have to implement an entire
reset function since there wasn't one previously, and
that requires a QOM cast macro that got omitted when this
device was QOMified.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1515506513-31961-4-git-send-email-peter.maydell@linaro.org
Since milkymist-memcard is still using the legacy SD card API,
the SD card created by sd_init() is not plugged into any bus.
This means that the controller has to reset it manually.
Failing to do this mostly didn't affect the guest since the
guest typically does a programmed SD card reset as part of
its SD controller driver initialization, but meant that
migration failed because it's only in sd_reset() that we
set up the wpgrps_size field.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1515506513-31961-3-git-send-email-peter.maydell@linaro.org
Since pl181 is still using the legacy SD card API, the SD
card created by sd_init() is not plugged into any bus. This
means that the controller has to reset it manually.
Failing to do this mostly didn't affect the guest since the
guest typically does a programmed SD card reset as part of
its SD controller driver initialization, but meant that
migration failed because it's only in sd_reset() that we
set up the wpgrps_size field.
Cc: qemu-stable@nongnu.org
Fixes: https://bugs.launchpad.net/qemu/+bug/1739378
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1515506513-31961-2-git-send-email-peter.maydell@linaro.org
Peter Maydell