From 03a31776e8fb239fee98625dd83b85f5cbe3ccba Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Mon, 23 Jul 2018 15:21:26 +0100 Subject: [PATCH] hw/sd/bcm2835_sdhost: Fix PIO mode writes Writes in PIO mode have two requirements: - A data interrupt must be generated after a write command has been issued to indicate that the chip is ready to receive data. - A block interrupt must be generated after each block to indicate that the chip is ready to receive the next data block. Rearrange the code to make this happen. Tested on raspi3 (in PIO mode) and raspi2 (in DMA mode). Signed-off-by: Guenter Roeck Message-id: 1531779837-20557-1-git-send-email-linux@roeck-us.net Reviewed-by: Peter Maydell Signed-off-by: Peter Maydell --- hw/sd/bcm2835_sdhost.c | 20 ++++++++++++++++---- 1 file changed, 16 insertions(+), 4 deletions(-) diff --git a/hw/sd/bcm2835_sdhost.c b/hw/sd/bcm2835_sdhost.c index 4df4de7d67..1b760b2a7c 100644 --- a/hw/sd/bcm2835_sdhost.c +++ b/hw/sd/bcm2835_sdhost.c @@ -179,9 +179,11 @@ static void bcm2835_sdhost_fifo_run(BCM2835SDHostState *s) uint32_t value = 0; int n; int is_read; + int is_write; is_read = (s->cmd & SDCMD_READ_CMD) != 0; - if (s->datacnt != 0 && (!is_read || sdbus_data_ready(&s->sdbus))) { + is_write = (s->cmd & SDCMD_WRITE_CMD) != 0; + if (s->datacnt != 0 && (is_write || sdbus_data_ready(&s->sdbus))) { if (is_read) { n = 0; while (s->datacnt && s->fifo_len < BCM2835_SDHOST_FIFO_LEN) { @@ -201,8 +203,11 @@ static void bcm2835_sdhost_fifo_run(BCM2835SDHostState *s) if (n != 0) { bcm2835_sdhost_fifo_push(s, value); s->status |= SDHSTS_DATA_FLAG; + if (s->config & SDHCFG_DATA_IRPT_EN) { + s->status |= SDHSTS_SDIO_IRPT; + } } - } else { /* write */ + } else if (is_write) { /* write */ n = 0; while (s->datacnt > 0 && (s->fifo_len > 0 || n > 0)) { if (n == 0) { @@ -223,11 +228,18 @@ static void bcm2835_sdhost_fifo_run(BCM2835SDHostState *s) s->edm &= ~SDEDM_FSM_MASK; s->edm |= SDEDM_FSM_DATAMODE; trace_bcm2835_sdhost_edm_change("datacnt 0", s->edm); - - if ((s->cmd & SDCMD_WRITE_CMD) && + } + if (is_write) { + /* set block interrupt at end of each block transfer */ + if (s->hbct && s->datacnt % s->hbct == 0 && (s->config & SDHCFG_BLOCK_IRPT_EN)) { s->status |= SDHSTS_BLOCK_IRPT; } + /* set data interrupt after each transfer */ + s->status |= SDHSTS_DATA_FLAG; + if (s->config & SDHCFG_DATA_IRPT_EN) { + s->status |= SDHSTS_SDIO_IRPT; + } } }